Eran Harary [Tue, 3 Mar 2015 11:53:28 +0000 (13:53 +0200)]
iwlwifi: trans: Take ownership on secure machine before FW load
When we load the firmware for the 8000 B step device, it'll
verify its signature. In the current version of the
hardware, there can be a race between the WiFi firmware
being loaded and the Bluetooth firmware being loaded.
Check that WiFi is authenticated, if not, take ownership
on the authentication machine to make sure that the WiFi
firmware will be authenticated.
Signed-off-by: Eran Harary <eran.harary@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Arik Nemtsov [Sun, 22 Feb 2015 17:15:04 +0000 (19:15 +0200)]
iwlwifi: mvm: reflect TDLS pm state in mvmvif->pm_enabled
When entering D0i3, the MVM mutex cannot be grabbed. This interferes
with the calculation of the number of connected TDLS stations during
the setup of the power cmd.
The goal is to disable power saving for all vifs while any TDLS station
is connected. For this purpose it is enough to keep the pm_enabled
member of all mvmvifs as false. An update of the power state already
occurs when a TDLS station is added/removed, so the values are correctly
updated.
We don't need to acquire MAC access for each access, it
makes much more sense to keep the MAC access. This speeds
up the Tx DMA stop flow significantly.
Moreover, if one channel can't be stopped, stop the others
but don't poll for them to avoid being stuck there for a
long time.
This solves a situation in which we were stuck in that flow
for way too long with a spinlock held which led to a kernel
panic.
Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eran Harary [Wed, 25 Feb 2015 12:24:51 +0000 (14:24 +0200)]
iwlwifi: mvm: support family 8000 B2/C steps
In-order to recognize newer step of the device, the driver
must read the chip_version_id from the AUX bus MISC address
space. This will determine what firmware file will be
loaded.
Signed-off-by: Eran Harary <eran.harary@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Jonathan Doron [Thu, 27 Nov 2014 14:55:25 +0000 (16:55 +0200)]
iwlwifi: mvm: set LAR MCC on D3/D0 transitions
When moving to the D3 FW give it the valid MCC from the D0 FW. When
returning from D3 to D0, query the D3 FW for the latest MCC, as
it might have changed internally. This MCC will be replayed to the D0 FW
when it boots.
Signed-off-by: Jonathan Doron <jonathanx.doron@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Jonathan Doron [Thu, 27 Nov 2014 14:57:55 +0000 (16:57 +0200)]
iwlwifi: mvm: support LAR updates from BIOS
When booting the card, check for a dedicated regulatory ACPI entry. If
such exists, read it and give the information to FW with the appropriate
source.
Eran Harary [Sun, 8 Feb 2015 09:41:43 +0000 (11:41 +0200)]
iwlwifi: mvm: take the MAC address from HW registers
For some configurations, the driver should get the MAC
address from the hardware registers and not from the
regular locations. Since the parsing of the MAC address
is the same regardless of its source, continue the regular
code path (parsing) after we read the registers.
Signed-off-by: Eran Harary <eran.harary@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Chub (Communication Hub, CommsHUB) is a HW component that connects to the cellular
and connectivity cores that gets updates of mcc changes, and then notifies the FW
directly of any mcc change.
The ucode notifies the driver (via this command) that it should ask for an mcc update,
and the driver sends the ucode the update mcc command to set the updated regulatory info.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Arik Nemtsov [Thu, 30 Oct 2014 13:12:39 +0000 (15:12 +0200)]
iwlwifi: ignore IBSS flag as regulatory NO-IR indication
According to updated regulatory guidelines, the ACTIVE bit in the NVM
also allows ibss activity on the channel. The IBSS NVM bit is not updated
when LAR is active and is deprecated. Using this bit for NO-IR incorrectly
causes all 5Ghz channels to be marked as passive.
Arik Nemtsov [Sun, 23 Mar 2014 14:18:40 +0000 (16:18 +0200)]
iwlwifi: mvm: consider LAR support during NVM parse
Register to cfg80211 with all channels enabled when LAR is supported.
Appropriate channels will later be disabled when a specific regulatory
domain is defined.
Arik Nemtsov [Wed, 5 Mar 2014 10:19:10 +0000 (12:19 +0200)]
iwlwifi: create regdomain from mcc_update_cmd response
Parse the NVM channel data and create a regulatory domain with a rule
for every 20Mhz channel. Use the AUTO_BW flag so the regulatory core
can unify single-channel rules into ranges.
Arik Nemtsov [Tue, 4 Mar 2014 17:58:46 +0000 (19:58 +0200)]
iwlwifi: mvm: init country code on init/recovery
During init queue a regulatory update to retrieve the default
regulatory settings from FW. If we're during recovery, only replay the
current country code to FW, if it exists.
iwlwifi: fix max_ht_ampdu_exponent for older devices
The commit below didn't update the max_ht_ampdu_exponent
for the devices listed in iwl-[1-6]000.c which, in result,
became 0 instead of 8K. This reduced the size of the Rx
AMPDU from 64K to 8K which had an impact in the Rx
throughput. One user reported that because of this, his
downstream throughput droppped by a half.
iwlwifi: mvm: fix compilation with IWLWIFI_DEBUGFS not set
The commits below broke compilation when
CONFIG_IWLWIFI_DEBUGFS is not set.
FIx that.
Fixes: ddf89ab10a93 ("iwlwifi: mvm: allow to force the Rx chains from debugfs") Fixes: 9d761fd8a583 ("iwlwifi: mvm: add trigger for firmware dump upon missed beacons") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
David Spinadel [Tue, 17 Feb 2015 10:45:21 +0000 (12:45 +0200)]
iwlwifi: mvm: don't override passive dwell in case of fragmented scan
Currently scan params structure has only active or passive dwell time
fields, passive one is used for fragmented scans too. FW needs the
passive dwell time even when performing fragmented scan for calculating
time between channels. Add a separate parameter for fragmented dwell time
and pass both fragmented and passive to FW.
Signed-off-by: David Spinadel <david.spinadel@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi: mvm: add trigger for firmware dump upon statistics
It can be very useful to monitor the statistics and trigger
a firmware dump when a certain value hits a certain offset.
Since the statistics are huge, add a generic trigger. When
the DWORD at offset X reaches value Y.
Since there is another trigger before this one I can't add
right now because of a dependency on mac80211, add a
reserved entry to keep the enum in place.
iwlwifi: mvm: restart firmware recording when no configuration is set
Sometimes the firmware will have a hard coded configuration.
In this case, the driver won't find any configuration
in the firmware file, and it will have to re-start
recording in case it has been stopped. This can't be done
by the configuration host command since there is no such
host command configured. Do that with the registers instead.
iwlwifi: mvm: add trigger for firmware dump upon missed beacons
Missing beacons is a good indication that something is going
wrong in the firmware. Add a trigger to be able to collect
data when we start missing beacons with a configurable
threshold.
iwlwifi: mvm: add the cause of the firmware dump in the dump
Now that the firmware dump can be triggered by events in
the code and not only the user or an firmware ASSERT, we
need a way to know why the firmware dump was triggered.
Add a section in the dump file for that.
iwlwifi: mvm: add framework for triggers for fw dump
Most of the time, the issues we want to debug with the
firmware dump mechanism are transient. It is then very
hard to stop the recording on time and get meaningful
data.
In order to solve this, I add here an infrastucture
of triggers. The user will supply a list of triggers
that will start / stop the recording. We have two types
of triggers: start and stop. Start triggers can start a
specific configuration. The stop triggers will be able to
kick the collection of the data with the currently running
configuration. These triggers are given to the driver by
the .ucode file - just like the configuration.
In the next patches, I'll add triggers in the code.
Luciano Coelho [Fri, 13 Feb 2015 19:37:09 +0000 (21:37 +0200)]
iwlwifi: mvm: don't iterate interfaces to disconnect in net-detect
We shouldn't call iwl_mvm_d3_disconnect_iter() on the running
interfaces when we are woken up due to net-detect, because it doesn't
make sense. Additionally, this seems to set the
IEEE80211_SDATA_DISCONNECT_RESUME flag that will cause a disconnection
on the next resume (if a normal WoWLAN is used).
To solve this, skip the iteration loop when net-detect is set.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Reported-by: Samuel Tan <samueltan@chromium.org> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Wed, 21 Jan 2015 20:41:29 +0000 (21:41 +0100)]
iwlwifi: mvm: support beacon statistics for BSS client
Report the average beacon signal and the number of received beacons as
measured by the firmware.
Since the firmware just counts, and doesn't reset the counter at all,
clear it in the firmware whenever we associate. However, accumulate it
over firmware restart.
Since clearing the statistics in the firmware will also clear the ones
for the radio statistics, add those to the accumulator when cleared.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eran Harary [Tue, 10 Feb 2015 07:25:50 +0000 (09:25 +0200)]
iwlwifi: mvm: don't write to DBGC_OUT_CTRL when stopping the recording
Due to HW bug in the DBGC when driver want to stop the dbg recording it
should wait 100us before collecting the data instead of write 0 to
DBGC_OUT_CTRL.
Signed-off-by: Eran Harary <eran.harary@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Luciano Coelho [Tue, 10 Feb 2015 11:03:38 +0000 (13:03 +0200)]
iwlwifi: mvm: remove deprecated scan API code
The legacy scan API is deprecated and not used anymore with 10 and
higher firmware versions. Since we deprecated firmware version 9, we
can remove a whole lot of unused code.
Johannes Berg [Wed, 14 Jan 2015 17:12:41 +0000 (18:12 +0100)]
iwlwifi: mvm: support radio statistics as global survey
Export the radio statistics from the statistics v10 API (if the
firmware also has the capability to fill these statistics) using
the global survey data facility.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Wed, 14 Jan 2015 16:58:57 +0000 (17:58 +0100)]
iwlwifi: mvm: add statistics API version 10
New firmware versions will report statistics using a new version 10
of the API, instead of the current version 8. Add support for this.
This enables getting beacon and radio statistics.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The shared antenna should be forbidden to use only if there's
high BT activity. Comparing to BT_OFF was effectively causing
us to always forbid using the shared antenna for SISO. This
leads to degraded performance in scenarios where the shared
antenna would have better performance.
Eyal Shapira [Mon, 2 Feb 2015 10:14:54 +0000 (12:14 +0200)]
iwlwifi: mvm: rs: avoid ss_force from being reset after tx idle
ss_force is a debugging option to force a certain single stream
tx mode. It's not useful if it gets reset after tx idle. Fix that.
While at it also make sure any code touching ss_force will only
get compiled if debugfs support is configured.
Eyal Shapira [Thu, 29 Jan 2015 23:38:29 +0000 (01:38 +0200)]
iwlwifi: mvm: rs: adapt rate matching to new STBC/BFER
Once the FW supports autonomous decision between STBC/BFER/SISO
we no longer set the STBC bit and ANT_AB in the rate table.
However the FW rate in the tx response will have the STBC
or BFER bit set and the antennas set to ANT_AB in case these
were chosen by it. This will cause us to discard any such
response as unmatching the current LQ table and thus break
the rs search cycle completely.
Fix this by relaxing the rate matching in case we're working
with the new API and STBC/BFER are used.
Eyal Shapira [Mon, 2 Feb 2015 13:21:27 +0000 (15:21 +0200)]
iwlwifi: mvm: rs: fix BT Coex check to look at the correct ant
The check to avoid the shared antenna was passed the wrong
antenna parameter. It should have checked whether the antenna of
the next column we're considering is allowed and instead it was
passed the current antenna.
This could lead to a wrong choice of the next column in the rs
algorithm and non optimal performance.
Fixes: commit 219fb66b49fac64bb ("iwlwifi: mvm: rs - don't use the shared antenna when BT load is high") Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eyal Shapira [Fri, 30 Jan 2015 11:40:02 +0000 (13:40 +0200)]
iwlwifi: mvm: rs: better match tx response rate to the LQ table
Currently rs uses the info in mac80211 tx status which is
a translation of the actual rate coming up from the FW in
the tx response. This is matched up against the LQ table first
rate to make sure this tx frame used the current LQ table.
Instead of using the translated mac80211 info it's easier and
cleaner to just pass the actual tx response rate in the driver
private data and use that for matching.
This becomes even more important once the FW begins to
decide on its own whether to use STBC/BFER/SISO.
1) Missing netlink attribute validation in nft_lookup, from Patrick
McHardy.
2) Restrict ipv6 partial checksum handling to UDP, since that's the
only case it works for. From Vlad Yasevich.
3) Clear out silly device table sentinal macros used by SSB and BCMA
drivers. From Joe Perches.
4) Make sure the remote checksum code never creates a situation where
the remote checksum is applied yet the tunneling metadata describing
the remote checksum transformation is still present. Otherwise an
external entity might see this and apply the checksum again. From
Tom Herbert.
5) Use msecs_to_jiffies() where applicable, from Nicholas Mc Guire.
6) Don't explicitly initialize timer struct fields, use setup_timer()
and mod_timer() instead. From Vaishali Thakkar.
7) Don't invoke tg3_halt() without the tp->lock held, from Jun'ichi
Nomura.
8) Missing __percpu annotation in ipvlan driver, from Eric Dumazet.
9) Don't potentially perform skb_get() on shared skbs, also from Eric
Dumazet.
10) Fix COW'ing of metrics for non-DST_HOST routes in ipv6, from Martin
KaFai Lau.
11) Fix merge resolution error between the iov_iter changes in vhost and
some bug fixes that occurred at the same time. From Jason Wang.
12) If rtnl_configure_link() fails we have to perform a call to
->dellink() before unregistering the device. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
net: dsa: Set valid phy interface type
rtnetlink: call ->dellink on failure when ->newlink exists
com20020-pci: add support for eae single card
vhost_net: fix wrong iter offset when setting number of buffers
net: spelling fixes
net/core: Fix warning while make xmldocs caused by dev.c
net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081
ipv6: fix ipv6_cow_metrics for non DST_HOST case
openvswitch: Fix key serialization.
r8152: restore hw settings
hso: fix rx parsing logic when skb allocation fails
tcp: make sure skb is not shared before using skb_get()
bridge: netfilter: Move sysctl-specific error code inside #ifdef
ipv6: fix possible deadlock in ip6_fl_purge / ip6_fl_gc
ipvlan: add a missing __percpu pcpu_stats
tg3: Hold tp->lock before calling tg3_halt() from tg3_init_one()
bgmac: fix device initialization on Northstar SoCs (condition typo)
qlcnic: Delete existing multicast MAC list before adding new
net/mlx5_core: Fix configuration of log_uar_page_sz
sunvnet: don't change gso data on clones
...
Linus Torvalds [Wed, 18 Feb 2015 01:34:21 +0000 (17:34 -0800)]
Merge tag 'md/3.20-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"Three bug md fixes for 3.20
yet-another-livelock in raid5, and a problem with write errors to
4K-block devices"
* tag 'md/3.20-fixes' of git://neil.brown.name/md:
md/raid5: Fix livelock when array is both resyncing and degraded.
md/raid10: round up to bdev_logical_block_size in narrow_write_error.
md/raid1: round up to bdev_logical_block_size in narrow_write_error
Linus Torvalds [Wed, 18 Feb 2015 01:03:07 +0000 (17:03 -0800)]
Merge tag 'please-pull-fixmcelog' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull mcelog regression fix from Tony Luck:
"Fix regression - functions on the mce notifier chain should not be
able to decide that an event should not be logged"
* tag 'please-pull-fixmcelog' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
x86/mce: Fix regression. All error records should report via /dev/mcelog
Causes an RCW cycle to be forced even when the array is degraded.
A degraded array cannot support RCW as that requires reading all data
blocks, and one may be missing.
Forcing an RCW when it is not possible causes a live-lock and the code
spins, repeatedly deciding to do something that cannot succeed.
So change the condition to only force RCW on non-degraded arrays.
Linus Torvalds [Wed, 18 Feb 2015 00:12:34 +0000 (16:12 -0800)]
Merge branch 'lazytime' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull lazytime mount option support from Al Viro:
"Lazytime stuff from tytso"
* 'lazytime' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ext4: add optimization for the lazytime mount option
vfs: add find_inode_nowait() function
vfs: add support for a lazytime mount option
Linus Torvalds [Tue, 17 Feb 2015 23:48:33 +0000 (15:48 -0800)]
Merge branch 'iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull iov_iter updates from Al Viro:
"More iov_iter work - missing counterpart of iov_iter_init() for
bvec-backed ones and vfs_read_iter()/vfs_write_iter() - wrappers for
sync calls of ->read_iter()/->write_iter()"
* 'iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: add vfs_iter_{read,write} helpers
new helper: iov_iter_bvec()
Linus Torvalds [Tue, 17 Feb 2015 23:27:47 +0000 (15:27 -0800)]
Merge branch 'getname2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull getname/putname updates from Al Viro:
"Rework of getname/getname_kernel/etc., mostly from Paul Moore. Gets
rid of quite a pile of kludges between namei and audit..."
* 'getname2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
audit: replace getname()/putname() hacks with reference counters
audit: fix filename matching in __audit_inode() and __audit_inode_child()
audit: enable filename recording via getname_kernel()
simpler calling conventions for filename_mountpoint()
fs: create proper filename objects using getname_kernel()
fs: rework getname_kernel to handle up to PATH_MAX sized filenames
cut down the number of do_path_lookup() callers
Linus Torvalds [Tue, 17 Feb 2015 23:18:19 +0000 (15:18 -0800)]
Merge branch 'debugfs_automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull debugfs patches from Al Viro:
"debugfs patches, mostly to make it possible for something like tracefs
to be transparently automounted on given directory in debugfs.
New primitive in there is debugfs_create_automount(name, parent, func,
arg), which creates a directory and makes its ->d_automount() return
func(arg). Another missing primitive was debugfs_create_file_size() -
open-coded in quite a few places. Dave's patch adds it and converts
the open-code instances to calling it"
* 'debugfs_automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
debugfs: Provide a file creation function that also takes an initial size
new primitive: debugfs_create_automount()
debugfs: split end_creating() into success and failure cases
debugfs: take mode-dependent parts of debugfs_get_inode() into callers
fold debugfs_mknod() into callers
fold debugfs_create() into caller
fold debugfs_mkdir() into caller
debugfs_mknod(): get rid useless arguments
fold debugfs_link() into caller
debugfs: kill __create_file()
debugfs: split the beginning and the end of __create_file() off
debugfs_{mkdir,create,link}(): get rid of redundant argument
Linus Torvalds [Tue, 17 Feb 2015 22:56:45 +0000 (14:56 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc VFS updates from Al Viro:
"This cycle a lot of stuff sits on topical branches, so I'll be sending
more or less one pull request per branch.
This is the first pile; more to follow in a few. In this one are
several misc commits from early in the cycle (before I went for
separate branches), plus the rework of mntput/dput ordering on umount,
switching to use of fs_pin instead of convoluted games in
namespace_unlock()"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
switch the IO-triggering parts of umount to fs_pin
new fs_pin killing logics
allow attaching fs_pin to a group not associated with some superblock
get rid of the second argument of acct_kill()
take count and rcu_head out of fs_pin
dcache: let the dentry count go down to zero without taking d_lock
pull bumping refcount into ->kill()
kill pin_put()
mode_t whack-a-mole: chelsio
file->f_path.dentry is pinned down for as long as the file is open...
get rid of lustre_dump_dentry()
gut proc_register() a bit
kill d_validate()
ncpfs: get rid of d_validate() nonsense
selinuxfs: don't open-code d_genocide()
Linus Torvalds [Tue, 17 Feb 2015 22:35:02 +0000 (14:35 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge yet more updates from Andrew Morton:
- a pile of minor fs fixes and cleanups
- kexec updates
- random misc fixes in various places: vmcore, rbtree, eventfd, ipc, seccomp.
- a series of python-based kgdb helper scripts
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (58 commits)
seccomp: cap SECCOMP_RET_ERRNO data to MAX_ERRNO
samples/seccomp: improve label helper
ipc,sem: use current->state helpers
scripts/gdb: disable pagination while printing from breakpoint handler
scripts/gdb: define maintainer
scripts/gdb: convert CpuList to generator function
scripts/gdb: convert ModuleList to generator function
scripts/gdb: use a generator instead of iterator for task list
scripts/gdb: ignore byte-compiled python files
scripts/gdb: port to python3 / gdb7.7
scripts/gdb: add basic documentation
scripts/gdb: add lx-lsmod command
scripts/gdb: add class to iterate over CPU masks
scripts/gdb: add lx_current convenience function
scripts/gdb: add internal helper and convenience function for per-cpu lookup
scripts/gdb: add get_gdbserver_type helper
scripts/gdb: add internal helper and convenience function to retrieve thread_info
scripts/gdb: add is_target_arch helper
scripts/gdb: add helper and convenience function to look up tasks
scripts/gdb: add task iteration class
...
Kees Cook [Tue, 17 Feb 2015 21:48:00 +0000 (13:48 -0800)]
seccomp: cap SECCOMP_RET_ERRNO data to MAX_ERRNO
The value resulting from the SECCOMP_RET_DATA mask could exceed MAX_ERRNO
when setting errno during a SECCOMP_RET_ERRNO filter action. This makes
sure we have a reliable value being set, so that an invalid errno will not
be ignored by userspace.
Signed-off-by: Kees Cook <keescook@chromium.org> Reported-by: Dmitry V. Levin <ldv@altlinux.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Will Drewry <wad@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Davidlohr Bueso [Tue, 17 Feb 2015 21:47:55 +0000 (13:47 -0800)]
ipc,sem: use current->state helpers
Call __set_current_state() instead of assigning the new state directly.
These interfaces also aid CONFIG_DEBUG_ATOMIC_SLEEP environments, keeping
track of who changed the state.
Jan Kiszka [Tue, 17 Feb 2015 21:47:52 +0000 (13:47 -0800)]
scripts/gdb: disable pagination while printing from breakpoint handler
While reporting the (refreshed) list of modules on automatic updates we
may hit the page boundary of the output console and cause a stop if
pagination is enabled. However, gdb does not accept user input while
running over the breakpoint handler. So we get stuck, and the user is
forced to interrupt gdb.
Resolve this by disabling pagination during automatic symbol updates. We
restore the user's configuration once done.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Borislav Petkov <bp@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Wagner [Tue, 17 Feb 2015 21:47:41 +0000 (13:47 -0800)]
scripts/gdb: use a generator instead of iterator for task list
The iterator does not return any task_struct from the thread_group list
because the first condition in the 'if not t or ...' will only be the
first time None.
Instead of keeping track of the state ourself in the next() function, we
fall back using Python's generator.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Borislav Petkov <bp@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Thompson [Tue, 17 Feb 2015 21:47:38 +0000 (13:47 -0800)]
scripts/gdb: ignore byte-compiled python files
Using the gdb scripts leaves byte-compiled python files in the scripts/
directory. These should be ignored by git.
[jan.kiszka@siemens.com: drop redundant mrproper rule as suggested by Michal] Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Cc: Michal Marek <mmarek@suse.cz> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Borislav Petkov <bp@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I tried to use these scripts in an ubuntu 14.04 host (gdb 7.7 compiled
against python 3.3) but there were several errors.
I believe this patch fixes these issues so that the commands now work (I
tested lx-symbols, lx-dmesg, lx-lsmod).
Main issues that needed to be resolved:
* In python 2 iterators have a "next()" method. In python 3 it is
__next__() instead (so let's just add both).
* In older python versions there was an implicit conversion
in object.__format__() (used when an object is in string.format())
where it was converting the object to str first and then
calling str's __format__(). This has now been removed so
we must explicitly convert to str the objects for which
we need to keep this behavior.
* In dmesg.py: in python 3 log_buf is now a "memoryview" object
which needs to be converted to a string in order to use string
methods like "splitlines()". Luckily memoryview exists in
python 2.7.6 as well, so we can convert log_buf to memoryview
and use the same code in both python 2 and python 3.
This version of the patch has now been tested with gdb 7.7 and both python
3.4 and python 2.7.6 (I think asking for at least python 2.7.6 is a
reasonable requirement instead of complicating the code with version
checks etc).
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Borislav Petkov <bp@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kiszka [Tue, 17 Feb 2015 21:47:18 +0000 (13:47 -0800)]
scripts/gdb: add get_gdbserver_type helper
This helper probes the type of the gdb server. Supported are QEMU and
KGDB so far. Knowledge about the gdb server is required e.g. to
retrieve the current CPU or current task.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Borislav Petkov <bp@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kiszka [Tue, 17 Feb 2015 21:47:15 +0000 (13:47 -0800)]
scripts/gdb: add internal helper and convenience function to retrieve thread_info
Add the internal helper get_thread_info that calculates the thread_info
from a given task variable. Also export this service as a convenience
function.
Note: ia64 version is untested.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Borislav Petkov <bp@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / karo-tx-linux.git / log