Paolo Bonzini [Fri, 7 Sep 2012 15:30:35 +0000 (17:30 +0200)]
target: support zero-size allocation lengths in transport_kmap_data_sg
In order to support zero-size allocation lengths, do not assert
that we have a scatterlist until after checking cmd->data_length.
But once we do this, we can have two cases of transport_kmap_data_sg
returning NULL: a zero-size allocation length, or an out-of-memory
condition. Report the latter using sense codes, so that the SCSI
command that triggered it will fail.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Paolo Bonzini [Fri, 7 Sep 2012 15:30:34 +0000 (17:30 +0200)]
target: fail REPORT LUNS with less than 16 bytes of payload
SPC says:
"The ALLOCATION LENGTH field is defined in 4.3.5.6. The allocation length
should be at least 16. Device servers compliant with SPC return CHECK
CONDITION status, with the sense key set to ILLEGAL REQUEST, and the
additional sense code set to INVALID FIELD IN CDB when the allocation
length is less than 16 bytes".
Testcase: sg_raw -r8 /dev/sdb a0 00 00 00 00 00 00 00 00 08 00 00
should fail with ILLEGAL REQUEST / INVALID FIELD IN CDB sense
does not fail without the patch
fails correctly with the patch
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Several places were not checking that the parameter list length
was large enough, and thus accessing invalid memory. Zero-length
parameter lists are just a special case of this.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Paolo Bonzini [Fri, 7 Sep 2012 15:30:32 +0000 (17:30 +0200)]
target: go through normal processing for zero-length PSCSI commands
Right now, commands with a zero-size payload are skipped completely.
This is wrong; such commands should be passed down to the device and
processed normally.
For physical backends, this ignores completely things such as START
STOP UNIT. For virtual backends, we have a hack in place to clear a
unit attention state on a zero-size REQUEST SENSE, but we still do
not report errors properly on zero-length commands---out-of-bounds
0-block reads and writes, too small parameter list lengths, etc.
This patch fixes this for PSCSI. Uses of transport_kmap_data_sg are
guarded with a check for non-zero cmd->data_length; for all other
commands a zero length is handled properly in pscsi_execute_cmd.
The sole exception will be for now REPORT LUNS, which is handled
through the normal SPC emulation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Paolo Bonzini [Wed, 5 Sep 2012 15:09:15 +0000 (17:09 +0200)]
target: fix use-after-free with PSCSI sense data
The pointer to the sense buffer is fetched by transport_get_sense_data,
but this is called by target_complete_ok_work long after pscsi_req_done
has freed the struct that contains it.
Pass instead the fabric's sense buffer to transport_complete,
and copy the data to it directly in transport_complete. Setting
SCF_TRANSPORT_TASK_SENSE also becomes a duty of transport_complete.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Paolo Bonzini [Wed, 5 Sep 2012 15:09:14 +0000 (17:09 +0200)]
target: simplify code around transport_get_sense_data
The error conditions in transport_get_sense_data are superfluous
and complicate the code unnecessarily:
* SCF_TRANSPORT_TASK_SENSE is checked in the caller;
* it's simply part of the invariants of dev->transport->get_sense_buffer
that it must be there if transport_complete ever returns 1, and that
it must not return NULL. Besides, the entire callback will disappear
with the next patch.
* similarly in the caller we can expect that sense data is only sent
for non-zero cmd->scsi_status.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Benjamin Wang [Sun, 26 Aug 2012 10:04:10 +0000 (18:04 +0800)]
target: Check idr_get_new return value in iscsi_login_zero_tsih_s1
This patch updates iscsi_login_zero_tsih_s1() usage for generating
iscsi_session->session_index to properly check the return value from
idr_get_new(), and reject the iSCSI login attempt with exception
status ISCSI_LOGIN_STATUS_NO_RESOURCES in the event of a failure.
Signed-off-by: Benjamin Wang <cpwang2009@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Fix ->data_length re-assignment bug with SCSI overflow
This patch fixes a long-standing bug with SCSI overflow handling
where se_cmd->data_length was incorrectly being re-assigned to
the larger CDB extracted allocation length, resulting in a number
of fabric level errors that would end up causing a session reset
in most cases. So instead now:
- Only re-assign se_cmd->data_length durining UNDERFLOW (to use the
smaller value)
- Use existing se_cmd->data_length for OVERFLOW (to use the smaller
value)
This fix has been tested with the following CDB to generate an
SCSI overflow:
sg_raw -r512 /dev/sdc 28 0 0 0 0 0 0 0 9 0
Tested using iscsi-target, tcm_qla2xxx, loopback and tcm_vhost fabric
ports. Here is a bit more detail on each case:
- iscsi-target: Bug with open-iscsi with overflow, sg_raw returns
-3584 bytes of data.
- tcm_qla2xxx: Working as expected, returnins 512 bytes of data
- loopback: sg_raw returns CHECK_CONDITION, from overflow rejection
in transport_generic_map_mem_to_cmd()
- tcm_vhost: Same as loopback
Reported-by: Roland Dreier <roland@purestorage.com> Cc: Roland Dreier <roland@purestorage.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Boaz Harrosh <bharrosh@panasas.com> Cc: <stable@vger.kernel.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Denis Efremov [Sat, 18 Aug 2012 12:10:31 +0000 (16:10 +0400)]
tcm_fc: rcu_deref outside rcu lock/unlock section
Use rcu_dereference_protected in order to prevent lockdep
complaint. Sequel of the patch 863555be
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com> Acked-by: Mark D. Rustad <mark.d.rustad@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here TRANSPORT_IQN_LEN is 224, which is a multiple of 4.
Since vhost_tpgt is 2 bytes and abi_version is 4, the total size would
be 230. But gcc needs struct size be aligned to first field size, which
is 4 bytes, so it pads the structure by extra 2 bytes to the total of
232.
This padding is very undesirable in an ABI:
- it can not be initialized easily
- it can not be checked easily
- it can leak information between kernel and userspace
Simplest solution is probably just to make the padding
explicit.
(v2: Add check for zero'ed backend->reserved field for VHOST_SCSI_SET_ENDPOINT
and VHOST_SCSI_CLEAR_ENDPOINT ops as requested by MST)
Reported-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Fix regression bug with handling of zero-length data CDBs
This patch fixes a regression bug with the handling of zero-length
data CDBs within transport_generic_new_cmd() code. The bug was introduced
with the following commit as part of the single task conversion work:
where the zero-length check for SCF_SCSI_DATA_SG_IO_CDB was incorrectly
changed to SCF_SCSI_CONTROL_SG_IO_CDB because of the seperate comment
in transport_generic_new_cmd() wrt to control CDBs zero-length handling
introduced in:
target: Add workaround for zero-length control CDB handling
So go ahead and change transport_generic_new_cmd() to handle control+data
zero-length CDBs in the same manner for this special case.
Tested with iscsi-target + loopback fabric port LUNs on 3.6-rc0 code.
This patch will also need to be picked up for 3.5-stable.
(hch: Add proper comment in transport_generic_new_cmd)
Cc: Christoph Hellwig <hch@lst.de> Cc: Roland Dreier <roland@purestorage.com> Cc: Andy Grover <agrover@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target/pscsi: Fix bug with REPORT_LUNs handling for SCSI passthrough
This patch fixes a regression bug in pscsi_transport_complete() callback
code where *pt was being NULL dereferenced during REPORT_LUNS handling,
that was introduced with the spc/sbc refactoring in:
As this is a special case for pscsi_parse_cdb() to call spc_parse_cdb() to
allow TCM to handle REPORT_LUN emulation, pscsi_plugin_task will have not
been allocated..
So now in pscsi_transport_complete() just check for existence of *pt and
return for this special case.
Reported-by: Alex Elsayed <eternaleye+usenet@gmail.com> Cc: Alex Elsayed <eternaleye+usenet@gmail.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
tcm_vhost: Change vhost_scsi_target->vhost_wwpn to char *
This patch changes the vhost_scsi_target->vhost_wwpn[] type used
by VHOST_SCSI_* ioctls to 'char *' as requested by Blue Swirl in
order to match the latest QEMU vhost-scsi RFC-v3 userspace code.
Queuing this up into target-pending/master for a -rc3 PULL.
Reported-by: Blue Swirl <blauwirbel@gmail.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Yi Zou [Tue, 14 Aug 2012 23:06:43 +0000 (16:06 -0700)]
target: fix NULL pointer dereference bug alloc_page() fails to get memory
I am hitting this bug when the target is low in memory that fails the
alloc_page() for the newly submitted command. This is a sort of off-by-one
bug causing NULL pointer dereference in __free_page() since 'i' here is
really the counter of total pages that have been successfully allocated here.
Signed-off-by: Yi Zou <yi.zou@intel.com> Cc: Andy Grover <agrover@redhat.com> Cc: Nicholas Bellinger <nab@linux-iscsi.org> Cc: Open-FCoE.org <devel@open-fcoe.org> Cc: stable@vger.kernel.org Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Mark Rustad [Wed, 1 Aug 2012 21:51:53 +0000 (14:51 -0700)]
tcm_fc: Avoid debug overhead when not debugging
Stop doing a pile of work related to debugging messages when
the ft_debug_logging flag is not set. Use unlikely to add the
check in a way that the check can be inlined without inlining the
whole thing.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
tcm_vhost: Post-merge review changes requested by MST
This patch contains the post RFC-v5 (post-merge) changes, this includes:
- Add locking comment
- Move vhost_scsi_complete_cmd ahead of TFO callbacks in order to
drop forward declarations
- Drop extra '!= NULL' usage in vhost_scsi_complete_cmd_work()
- Change vhost_scsi_*_handle_kick() to use pr_debug
- Fix possible race in vhost_scsi_set_endpoint() for vs->vs_tpg checking
+ assignment.
- Convert tv_tpg->tpg_vhost_count + ->tv_tpg_port_count from atomic_t ->
int, and make sure reference is protected by ->tv_tpg_mutex.
- Drop unnecessary vhost_scsi->vhost_ref_cnt
- Add 'err:' label for exception path in vhost_scsi_clear_endpoint()
- Add enum for VQ numbers, add usage in vhost_scsi_open()
- Add vhost_scsi_flush() + vhost_scsi_flush_vq() following
drivers/vhost/net.c
- Add smp_wmb() + vhost_scsi_flush() call during vhost_scsi_set_features()
- Drop unnecessary copy_from_user() usage with GET_ABI_VERSION ioctl
- Add missing vhost_scsi_compat_ioctl() caller for vhost_scsi_fops
- Fix function parameter definition first line to follow existing
vhost code style
- Change 'vHost' usage -> 'vhost' in handful of locations
- Change -EPERM -> -EBUSY usage for two failures in tcm_vhost_drop_nexus()
- Add comment for tcm_vhost_workqueue in tcm_vhost_init()
- Make GET_ABI_VERSION return 'int' + add comment in tcm_vhost.h
Reported-by: Michael S. Tsirkin <mst@redhat.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com> Cc: Anthony Liguori <aliguori@us.ibm.com> Cc: Zhi Yong Wu <wuzhy@cn.ibm.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Ian Kent [Mon, 6 Aug 2012 01:37:47 +0000 (09:37 +0800)]
autofs4 - fix get_next_positive_subdir()
Following a report of a crash during an automount expire I found that
the locking in fs/autofs4/expire.c:get_next_positive_subdir() was wrong.
Not only is the locking wrong but the function is more complex than it
needs to be.
The function is meant to calculate (and dget) the next entry in the list
of directories contained in the root of an autofs mount point (an autofs
indirect mount to be precise). The main problem was that the d_lock of
the owner of the list was not being taken when walking the list, which
lead to list corruption under load. The only other lock that needs to
be taken is against the next dentry candidate so it can be checked for
usability.
Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 16 Aug 2012 18:47:42 +0000 (11:47 -0700)]
Merge tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO fix from Alex Williamson:
"Just a trivial patch to include vfio.h in the installed headers so we
can complete userspace integration into QEMU."
* tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio:
vfio: Include vfio.h in installed headers
Linus Torvalds [Thu, 16 Aug 2012 18:31:59 +0000 (11:31 -0700)]
Merge tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fix from Konrad Rzeszutek Wilk:
"Way back in v3.5 we added a mechanism to populate back pages that were
released (they overlapped with MMIO regions), but neglected to reserve
the proper amount of virtual space for extend_brk to work properly.
Coincidentally some other commit aligned the _brk space to larger area
so I didn't trigger this until it was run on a machine with more than
2GB of MMIO space."
* On machines with large MMIO/PCI E820 spaces we fail to boot b/c
we failed to pre-allocate large enough virtual space for extend_brk.
* tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.
Linus Torvalds [Thu, 16 Aug 2012 18:13:16 +0000 (11:13 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull two slave-dmaengine fixes from Vinod Koul:
"One fixes the correct use of clock API in imx driver and the other
enables clock for tegra driver, which is used for other tegra driver
conversion to dmanegine in -next."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: enable/disable dma clock
dma: imx-dma: Fix kernel crash due to missing clock conversion
Linus Torvalds [Thu, 16 Aug 2012 18:08:32 +0000 (11:08 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull more drm fixes from Dave Airlie:
"Just some intel and nouveau ones this time, intel has more edp panel
fixes for macbooks and nouveau has a suspend/resume regression fix in
there."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
drm/nve0/fifo: add support for the flip completion swmthd
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Be less verbose during vmemmap population.
sparc64: do not clobber personality flags in sys_sparc64_personality()
Dave Airlie [Wed, 15 Aug 2012 10:31:22 +0000 (20:31 +1000)]
Merge branch 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/nve0/fifo: add support for the flip completion swmthd
Dave Airlie [Wed, 15 Aug 2012 10:27:51 +0000 (20:27 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel Vetter writes:
"A few important fixers:
- fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai)
- make the retina mbp work (ignore bogus edp bpc value in vbt)
- fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula)
- fix an edp panel power sequence regression, fixes the new macbook air
- apply the tlb invalidate w/a
Otherwise we still have another gmbus regression (patches are awaiting
tested-bys) and there's something odd going with some rare systems not
entering rc6 often enough (and hence blowing through too much power). It
seems to be a timing-related issue and can be mitigated by frobbing the
magic tuning parameters. We're still working on that one. Also, we still
have some fallout from the hw context support, but you can only hit that
with mesa master."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
David S. Miller [Wed, 15 Aug 2012 07:37:29 +0000 (00:37 -0700)]
sparc64: Be less verbose during vmemmap population.
On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.
This mimicks Yinghai Lu's x86 commit c2b91e2eec9678dbda274e906cc32ea8f711da3b
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.
This decreases the output by an order of 16.
Also demote this to KERN_DEBUG.
Signed-off-by: David S. Miller <davem@davemloft.net>
drm/i915: Only apply the SNB pipe control w/a to gen6
Note: Manually switch the pipe_control cmd to 4 dwords to avoid a
(silent) functional conflict with -next. This way will get a loud (but
conflict with next (since the scratch_addr has been deleted there).
Reported-and-tested-by: yex.tian@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322 Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: added note about merge conflict with -next.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: enable vdd when switching off the eDP panel
But that patch also tried to fix some neat edp sequence issue with the
force_vdd timings. Closer inspection reveals that we've raised
force_vdd only to do the aux channel communication dp_sink_dpms. If we
move the edp_panel_off below that, we don't need any force_vdd for the
disable sequence, which makes the Air happy.
Unfortunately the reporter of the original bug that the above commit
fixed is travelling, so we can't test whether this regresses things.
But my theory is that since we don't check for any power-off ->
force_vdd-on delays in edp_panel_vdd_on, this was the actual
root-cause of this failure. With that force_vdd dance completely
eliminated, I'm hopeful the original bug stays fixed, too.
For reference the old bug, which hopefully doesn't get broken by this:
https://bugzilla.kernel.org/show_bug.cgi?id=43163
In any case, regression fixers win over plain bugfixes, so this needs
to go in asap.
v2: The crucial pieces seems to be to clear the force_vdd flag
uncoditionally, too, in edp_panel_off. Looks like this is left behind
by the firmware somehow.
v3: The Apple firmware seems to switch off the panel on it's own, hence
we still need to keep force_vdd on, but properly clear it when switching
the panel off.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671 Tested-by: Roberto Romer <sildurin@gmail.com> Tested-by: Daniel Wagner <wagi@monom.org> Tested-by: Keith Packard <keithp@keithp.com> Cc: stable@vger.kernel.org Cc: Keith Packard <keithp@keithp.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Linus Torvalds [Tue, 14 Aug 2012 04:58:59 +0000 (07:58 +0300)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"Included are bug fixes and a patch to enable system call filtering
with BPF."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/compat: fix mmap compat system calls
s390/compat: fix compat wrappers for process_vm system calls
s390: do not clobber personality flags in sys_32_personality()
s390/seccomp: add support for system call filtering using BPF
s390/sclp_sdias: Add missing break and "fall through"
s390/mm: remove MAX_PHYSADDR_BITS define
Linus Torvalds [Tue, 14 Aug 2012 04:52:41 +0000 (07:52 +0300)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon and intel fixes mostly, one fix to the mgag200 driver to not
hang on certain server variants."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (32 commits)
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
drm/mgag200: fix G200ER pll picking algorithm
drm/edid: Fix potential memory leak in edid_load()
drm/udl: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
drm/radeon/kms: allow "invalid" DB formats as a means to disable DB
...
Arnd Bergmann [Mon, 13 Aug 2012 14:36:10 +0000 (14:36 +0000)]
GPIO: gpio-pxa: fix building without CONFIG_OF
Commit 7212157267 ("GPIO: gpio-pxa: fix devicetree functions") added an
"xlate" function pointer to the irq_domain_ops, but this function is nor
declared or defined anywhere when CONFIG_OF is disabled, causing the
build error:
drivers/gpio/gpio-pxa.c:532:11: error: 'irq_domain_xlate_twocell' undeclared here (not in a function)
Extending the DT-only code section to cover the irq_domain_ops and the
pxa_gpio_dt_ids solves this problem and makes it clearer which code is
actually used without DT.
Ben Skeggs [Fri, 27 Jul 2012 04:18:03 +0000 (14:18 +1000)]
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
At least partially fixes DP output detection on W530. Not sure if more
issues remain, or if my adaptor is just behaving weirdly (it does that
sometimes).
Dave Airlie [Mon, 13 Aug 2012 23:25:01 +0000 (09:25 +1000)]
Merge branch 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex Deucher writes:
This is the current set of radeon fixes for 3.6. Nothing too major.
Highlights:
- various display fixes
- some SI fixes
- new SI pci ids
- major VM fix
- CS checker support for MSAA
I've tested on a number of cards across generations and noticed no problems.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
Jani Nikula [Mon, 13 Aug 2012 14:33:02 +0000 (17:33 +0300)]
drm/i915: ensure i2c adapter is all set before adding it
i2c_add_adapter() may do i2c transfers on the bus to detect supported
devices. Therefore the adapter needs to be all set before adding it. This
was not the case for the bit-banging fallback, resulting in an oops if the
device detection GMBUS transfers timed out. Fix the issue by calling
i2c_add_adapter() only after intel_gpio_setup().
LKML-Reference: <5021F00B.7000503@ionic.de> Tested-by: Mihai Moldovan <ionic@ionic.de> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jerome Glisse [Mon, 6 Aug 2012 16:32:21 +0000 (12:32 -0400)]
drm/radeon: fence virtual address and free it once idle v4
Virtual address need to be fenced to know when we can safely remove it.
This patch also properly clear the pagetable. Previously it was
serouisly broken.
Kernel 3.5/3.4 need a similar patch but adapted for difference in mutex locking.
v2: For to update pagetable when unbinding bo (don't bailout if
bo_va->valid is true).
v3: Add kernel 3.5/3.4 comment.
v4: Fix compilation warnings.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
drm/radeon: do not reenable crtc after moving vram start address
It seems we can not update the crtc scanout address. After disabling
crtc, update to base address do not take effect after crtc being
reenable leading to at least frame being scanout from the old crtc
base address. Disabling crtc display request lead to same behavior.
So after changing the vram address if we don't keep crtc disabled
we will have the GPU trying to read some random system memory address
with some iommu this will broke the crtc engine and will lead to
broken display and iommu error message.
So to avoid this, disable crtc. For flicker less boot we will need
to avoid moving the vram start address.
Alex Deucher [Thu, 26 Jul 2012 17:38:52 +0000 (13:38 -0400)]
drm/radeon: properly handle crtc powergating
Need to make sure the crtc is gated on before modesetting.
Explicitly gate the crtc on in prepare() and set a flag
so that the dpms functions don't gate it off during
mode set.
Noticed by sylware on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Arnd Bergmann [Wed, 8 Aug 2012 21:27:58 +0000 (05:27 +0800)]
leds: renesas: fix error handling
bfe4c041 "leds: convert Renesas TPU LED driver to devm_kzalloc() and
cleanup error exit path" introduced a possible case in which r_tpu_probe
calls iounmap on a wild pointer. This changes the one case that was
missed in the same way as the other error paths.
Without this patch, building kota2_defconfig results in:
drivers/leds/leds-renesas-tpu.c: In function 'r_tpu_probe':
drivers/leds/leds-renesas-tpu.c:246:6: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-renesas-tpu.c:308:17: warning: 'p' may be used uninitialized in this function [-Wuninitialized]
Pull networking changes from David Miller:
"Most importantly this should cure the ipv4-mapped ipv6 socket TCP
crashes some people were seeing, otherwise:
1) Fix e1000e autonegotiation handling regression, from Tushar Dave.
2) Fix TX data corruption race on e1000e down, also from Tushar Dave.
3) Fix bfin_sir IRDA driver build, from Sonic Zhang.
4) AF_PACKET mmap() tests a flag in the TX ring shared between
userspace and the kernel for an internal consistency check. It
really shouldn't do this to validate the kernel's own behavior
because the user can corrupt it to be any value at all. From
Daniel Borkmann.
5) Fix TCP metrics leak on netns dismantle, from Eric Dumazet.
6) Orphan the anonymous TCP socket from the SKB in
ip_send_unicast_reply() so that the rest of the stack needn't see
it. Otherwise we get selinux problems of all sorts, from Eric
Dumazet.
This is the best way to fix this since the socket is just a place
holder for sending packets in a context where we have no real
socket at all.
7) Fix TUN detach crashes, from Stanislav Kinsbursky.
8) dev_set_alias() leaks memory on krealloc() failure, from Alexey
Khoroshilov.
9) FIB trie must use call_rcu() not call_rcu_bh(), because this code
is not universally invoked from software interrupts. From Eric
Dumazet.
10) PPTP looks up ipv4 routes with the wrong network namespace, fix
from Gao Feng."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
bnx2x: Fix compiler warnings
af_packet: remove BUG statement in tpacket_destruct_skb
macvtap: rcu_dereference outside read-lock section
codel: refine one condition to avoid a nul rec_inv_sqrt
ixgbe: add missing braces
ipv4: fix ip_send_skb()
net: tcp: ipv6_mapped needs sk_rx_dst_set method
ipv4: tcp: unicast_sock should not land outside of TCP stack
bnx2x: Fix recovery flow cleanup during probe
bnx2x: fix unload previous driver flow when flr-capable
tun: don't zeroize sock->file on detach
igb: Fix register defines for all non-82575 hardware
e1000e: fix panic while dumping packets on Tx hang with IOMMU
igb: fix panic while dumping packets on Tx hang with IOMMU
tcp: must free metrics at net dismantle
net/stmmac: mark probe function as __devinit
lpc_eth: remove obsolete ifdefs
net/core: Fix potential memory leak in dev_set_alias()
cdc-phonet: Don't leak in usbpn_open
batman-adv: Fix mem leak in the batadv_tt_local_event() function
...
Linus Torvalds [Mon, 13 Aug 2012 05:40:51 +0000 (08:40 +0300)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull tcm_vhost level target fabric driver from Nicholas Bellinger:
"Here is the PULL request for the initial merge of tcm_vhost based on
RFC-v5 code with MST's ACK appended to the initial merge commit."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcm_vhost: Initial merge for vhost level target fabric driver
Joren Van Onder [Sat, 11 Aug 2012 17:10:35 +0000 (17:10 +0000)]
bnx2x: Fix compiler warnings
Fix the following compiler warnings:
- drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:2908:3: warning: comparison
of distinct pointer types lacks a cast [enabled by default]
- drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c:1709:7: warning: comparison
of distinct pointer types lacks a cast [enabled by default]
Signed-off-by: Joren Van Onder <joren.vanonder@gmail.com> Acked-By: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
af_packet: remove BUG statement in tpacket_destruct_skb
Here's a quote of the comment about the BUG macro from asm-generic/bug.h:
Don't use BUG() or BUG_ON() unless there's really no way out; one
example might be detecting data structure corruption in the middle
of an operation that can't be backed out of. If the (sub)system
can somehow continue operating, perhaps with reduced functionality,
it's probably not BUG-worthy.
If you're tempted to BUG(), think again: is completely giving up
really the *only* solution? There are usually better options, where
users don't need to reboot ASAP and can mostly shut down cleanly.
In our case, the status flag of a ring buffer slot is managed from both sides,
the kernel space and the user space. This means that even though the kernel
side might work as expected, the user space screws up and changes this flag
right between the send(2) is triggered when the flag is changed to
TP_STATUS_SENDING and a given skb is destructed after some time. Then, this
will hit the BUG macro. As David suggested, the best solution is to simply
remove this statement since it cannot be used for kernel side internal
consistency checks. I've tested it and the system still behaves /stable/ in
this case, so in accordance with the above comment, we should rather remove it.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
rcu_dereference occurs in update section. Replacement by
rcu_dereference_protected in order to prevent lockdep
complaint.
Found by Linux Driver Verification project (linuxtesting.org)
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 12 Aug 2012 18:45:33 +0000 (21:45 +0300)]
Merge tag 'gpio-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
- Fix a resource leak in the SCH driver
- Fix the register address calculation in the MSIC driver
- Fix the PXA driver's devicetree functions
- Delete redundant shadow variable leftovers in the MXC driver
- Specify the GPIO base for the device tree probe in the MXC driver
- Add a modalias for the i.MX driver
- Fix off-by-one bug in the Samsung driver
- Fix erroneous errorpath in the Langwell driver
* tag 'gpio-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
drivers/gpio/gpio-langwell.c: fix error return code
gpio: samsung: Fix off-by-one bug in gpio addresses
ARM: dts: imx: add alias for gpio
gpio/mxc: specify gpio base for device tree probe
gpio/mxc: remove redundant shadow variables initialization
GPIO: gpio-pxa: fix devicetree functions
gpio: msic: Fix calculating register address in msic_gpio_to_oreg()
gpio-sch: Fix leak of resource
Linus Torvalds [Sun, 12 Aug 2012 18:34:09 +0000 (21:34 +0300)]
Merge tag 'pm-for-3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
- Fix for two recent regressions in the generic PM domains framework.
- Revert of a commit that introduced a resume regression and is
conceptually incorrect in my opinion.
- Fix for a return value in pcc-cpufreq.c from Julia Lawall.
- RTC wakeup signaling fix from Neil Brown.
- Suppression of compiler warnings for CONFIG_PM_SLEEP unset in ACPI,
platform/x86 and TPM drivers.
* tag 'pm-for-3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tpm_tis / PM: Fix unused function warning for CONFIG_PM_SLEEP
platform / x86 / PM: Fix unused function warnings for CONFIG_PM_SLEEP
ACPI / PM: Fix unused function warnings for CONFIG_PM_SLEEP
Revert "NMI watchdog: fix for lockup detector breakage on resume"
PM: Make dev_pm_get_subsys_data() always return 0 on success
drivers/cpufreq/pcc-cpufreq.c: fix error return code
RTC: Avoid races between RTC alarm wakeup and suspend.
Linus Torvalds [Sun, 12 Aug 2012 18:31:44 +0000 (21:31 +0300)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Arnd Bergmann:
"These are a bunch of bug fixes that came in after the merge window and
one update for the MAINTAINERS file.
The largest part of the fixes are patches that address bugs found by
building all the ARM defconfig files. There are a lot more warnings
that we have patches for, but the others are either still under
discussion or are harmless and do not cause actual problems besides
making the build slightly noisy."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: davinci: remove broken ntosd2_init_i2c
ARM: s3c24xx: enable CONFIG_BUG for tct_hammer
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
ARM: imx: gpmi-nand depends on mxs-dma
ARM: integrator: include <linux/export.h>
ARM: s3c24xx: use new PWM driver
ARM: sa1100: include linux/io.h in hackkit leds code
Input: eeti_ts: pass gpio value instead of IRQ
ARM: pxa: remove irq_to_gpio from ezx-pcap driver
ARM: tegra: more regulator fixes for Harmony
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
ARM: kirkwood: fix typo in Makefile.boot
i.MX27: Fix emma-prp and csi clocks.
ARM: integrator: use clk_prepare_enable() for timer
MAINTAINERS: update entry for Linus Walleij
...
Jeff Mahoney [Fri, 10 Aug 2012 19:07:09 +0000 (15:07 -0400)]
printk: Fix calculation of length used to discard records
While tracking down a weird buffer overflow issue in a program that
looked to be sane, I started double checking the length returned by
syslog(SYSLOG_ACTION_READ_ALL, ...) to make sure it wasn't overflowing
the buffer.
It turns out that the loops that calculate how much space the entries
will take when they're copied don't include the newlines and prefixes
that will be included in the final output since prev flags is passed as
zero.
This patch properly accounts for it and fixes the overflow.
CC: stable@kernel.org Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Sat, 11 Aug 2012 06:56:42 +0000 (08:56 +0200)]
drm/i915: Fix blank panel at reopening lid
When you reopen the lid on a laptop with PCH, the panel suddenly goes
blank sometimes. It seems because BLC_PWM_CPU_CTL register is cleared
to zero when BLC_PWM_CPU_CTL2 and BLC_PWM_PCH_CTL1 registers are
enabled.
This patch fixes the problem by moving the call of the function setting
BLC_PWM_CPU_CTL after enabling other two registers.
Eric Dumazet [Sun, 29 Jul 2012 20:52:21 +0000 (20:52 +0000)]
codel: refine one condition to avoid a nul rec_inv_sqrt
One condition before codel_Newton_step() was not good if
we never left the dropping state for a flow. As a result
rec_inv_sqrt was 0, instead of the ~0 initial value.
codel control law was then set to a very aggressive mode, dropping
many packets before reaching 'target' and recovering from this problem.
To keep codel_vars_init() as efficient as possible, refine
the condition to make sure rec_inv_sqrt initial value is correct
Many thanks to Anton Mich for discovering the issue and suggesting
a fix.
Reported-by: Anton Mich <lp2s1h@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Emil Tantilov [Fri, 10 Aug 2012 07:35:14 +0000 (07:35 +0000)]
ixgbe: add missing braces
This patch adds missing braces around the 10gig link check to include the check for KR support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Reported-by: Sascha Wildner <saw@online.de> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 Aug 2012 23:26:41 +0000 (16:26 -0700)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Here is a handful of fixes intended for 3.6.
Daniel Drake offers a cfg80211 fix to consume pending events before
taking a wireless device down. This prevents a resource leak.
Stanislaw Gruszka gives us a fix for a NULL pointer dereference in
rt61pci.
Johannes Berg provides an iwlwifi patch to disable "greenfield" mode.
Use of that mode was causing a rate scaling problem in for iwlwifi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tpm_tis / PM: Fix unused function warning for CONFIG_PM_SLEEP
According to a compiler warning, the tpm_tis_resume() function is not
used for CONFIG_PM_SLEEP unset, so add a #ifdef to prevent it from
being built in that case.
platform / x86 / PM: Fix unused function warnings for CONFIG_PM_SLEEP
According to compiler warnings, quite some suspend/resume functions
in platform x86 drivers are not used for CONFIG_PM_SLEEP unset, so
add #ifdefs to prevent them from being built in that case.
ACPI / PM: Fix unused function warnings for CONFIG_PM_SLEEP
According to compiler warnings, several suspend/resume functions
in ACPI drivers are not used for CONFIG_PM_SLEEP unset, so add
#ifdefs to prevent them from being built in that case.
ntosd2_init_i2c walks the ntosd2_i2c_info array, which it expects to
be populated with at least one member. gcc correctly warns about
the out-of-bounds access here.
Since this can not possibly work, it's better to disable i2c
support entirely on this board.
Without this patch, building davinci_all_defconfig results in:
arch/arm/mach-davinci/board-neuros-osd2.c: In function 'davinci_ntosd2_init':
arch/arm/mach-davinci/board-neuros-osd2.c:187:20: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Sekhar Nori <nsekhar@ti.com> Cc: Kevin Hilman <khilman@ti.com> Cc: Andrey Porodko <panda@chelcom.ru>
Arnd Bergmann [Thu, 3 May 2012 12:47:54 +0000 (12:47 +0000)]
ARM: s3c24xx: enable CONFIG_BUG for tct_hammer
Disabling CONFIG_BUG creates an insane amount of build warnings, which
makes it useless to check for building defconfigs to see if new
warnings show up.
Without this patch, building tct_hammer_defconfig results in:
net/packet/af_packet.c: In function 'tpacket_rcv':
net/packet/af_packet.c:1889:30: warning: 'hdrlen' may be used uninitialized in this function [-Wuninitialized]
net/core/ethtool.c: In function 'ethtool_get_feature_mask':
net/core/ethtool.c:213:1: warning: control reaches end of non-void function [-Wreturn-type]
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:2914:1: warning: control reaches end of non-void function [-Wreturn-type]
mm/bootmem.c: In function 'mark_bootmem':
mm/bootmem.c:352:1: warning: control reaches end of non-void function [-Wreturn-type]
net/core/dev.c: In function 'skb_warn_bad_offload':
net/core/dev.c:1904:33: warning: unused variable 'null_features' [-Wunused-variable]
drivers/mtd/chips/cfi_probe.c: In function 'cfi_chip_setup':
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
include/linux/mtd/map.h:394:11: note: 'r.x[0]' was declared here
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
(and many more)
The size of vmlinux increases by 1.78% because of this:
size obj-arm/vmlinux.nobug
text data bss dec hex filename 2108474 116916 55352 2280742 22cd26 obj-arm/vmlinux
size obj-arm/vmlinux.bug
text data bss dec hex filename 2150804 116916 53696 2321416 236c08 obj-arm/vmlinux
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Cc: Ben Dooks <ben-linux@fluff.org>
Arnd Bergmann [Fri, 10 Aug 2012 10:28:57 +0000 (12:28 +0200)]
Merge branch 'testing/new-warnings' into fixes
These patches all fix bugs that were newly introduced in v3.6-rc1
and found because they cause a gcc warning with one of the ARM
defconfigs. Most of them are harmless, but since we're trying
to get rid of all warnings eventually, we can start with the ones
that were not there before.
* testing/new-warnings:
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
Arnd Bergmann [Sat, 4 Aug 2012 07:11:34 +0000 (07:11 +0000)]
omap-rng: fix use of SIMPLE_DEV_PM_OPS
omap_rng_suspend and omap_rng_resume are unused if CONFIG_PM is enabled
but CONFIG_PM_SLEEP is disabled. I found this while building all defconfig
files on ARM. It's not clear to me if this is the right solution, but
at least it makes the code consistent again.
Without this patch, building omap1_defconfig results in:
drivers/char/hw_random/omap-rng.c:165:12: warning: 'omap_rng_suspend' defined but not used [-Wunused-function]
drivers/char/hw_random/omap-rng.c:171:12: warning: 'omap_rng_resume' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Kevin Hilman <khilman@ti.com> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Herbert Xu <herbert@gondor.apana.org.au>
Arnd Bergmann [Sat, 4 Aug 2012 11:18:20 +0000 (11:18 +0000)]
spi/s3c64xx: improve error handling
When a device tree definition os an s3c64xx SPI master is missing
a "controller-data" subnode, the newly added s3c64xx_get_slave_ctrldata
function might use uninitialized memory in place of that node,
which was correctly reported by gcc.
Without this patch, building s3c6400_defconfig results in:
drivers/spi/spi-s3c64xx.c: In function 's3c64xx_get_slave_ctrldata.isra.25':
drivers/spi/spi-s3c64xx.c:841:5: warning: 'data_np' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Cc: Jaswinder Singh <jaswinder.singh@linaro.org> Cc: Grant Likely <grant.likely@secretlab.ca>
The newly added dmaengine support in the omap2 nand driver
potentially causes an undefined return value from the
omap_nand_probe function when dmaengine_slave_config
reports an error. Let's handle this by returning the
same error back to the caller.
Without this patch, building omap2plus_defconfig results in:
drivers/mtd/nand/omap2.c: In function 'omap_nand_probe':
drivers/mtd/nand/omap2.c:1154:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Grazvydas Ignotas <notasas@gmail.com>
Arnd Bergmann [Sat, 4 Aug 2012 10:33:24 +0000 (10:33 +0000)]
gpio: em: do not discard em_gio_irq_domain_cleanup
The newly added gpio-em driver marks its em_gio_irq_domain_cleanup
function as __devexit, which would lead to that function being
discarded in case CONFIG_HOTPLUG is disabled. However, the function
is also called by the error handling logic em_gio_probe, which
would cause a jump into a NULL pointer if it was removed from the
kernel or module.
Without this patch, building kzm9d_defconfig results in:
WARNING: drivers/gpio/built-in.o(.devinit.text+0x330): Section mismatch in reference from the function em_gio_probe() to the function .devexit.text:em_gio_irq_domain_cleanup()
The function __devinit em_gio_probe() references
a function __devexit em_gio_irq_domain_cleanup().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
em_gio_irq_domain_cleanup() so it may be used outside an exit section.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Magnus Damm <damm@opensource.se> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Rafael J. Wysocki <rjw@sisk.pl>
Arnd Bergmann [Sat, 4 Aug 2012 10:28:33 +0000 (10:28 +0000)]
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
exynos_pm_add_dev_to_genpd is used if one or more out of a large
number of Kconfig symbols are enabled. However the new
exynos_defconfig selects none of those, so the function becomes
unused. Marking it so lets the compiler automatically discard
it.
Without this patch, building exynos_defconfig results in:
arch/arm/mach-exynos/pm_domains.c:118:123: warning: 'exynos_pm_add_dev_to_genpd' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Cc: Rafael J. Wysocki <rjw@sisk.pl>
Kees Cook [Fri, 10 Aug 2012 02:01:26 +0000 (19:01 -0700)]
Yama: higher restrictions should block PTRACE_TRACEME
The higher ptrace restriction levels should be blocking even
PTRACE_TRACEME requests. The comments in the LSM documentation are
misleading about when the checks happen (the parent does not go through
security_ptrace_access_check() on a PTRACE_TRACEME call).
Signed-off-by: Kees Cook <keescook@chromium.org> Cc: stable@vger.kernel.org # 3.5.x and later Signed-off-by: James Morris <james.l.morris@oracle.com>
Fix this using inet_sk_rx_dst_set(), and export this function in case
IPv6 is modular.
Reported-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 9 Aug 2012 13:56:06 +0000 (13:56 +0000)]
ipv4: tcp: unicast_sock should not land outside of TCP stack
commit be9f4a44e7d41cee (ipv4: tcp: remove per net tcp_sock) added a
selinux regression, reported and bisected by John Stultz
selinux_ip_postroute_compat() expect to find a valid sk->sk_security
pointer, but this field is NULL for unicast_sock
It turns out that unicast_sock are really temporary stuff to be able
to reuse part of IP stack (ip_append_data()/ip_push_pending_frames())
Fact is that frames sent by ip_send_unicast_reply() should be orphaned
to not fool LSM.
Note IPv6 never had this problem, as tcp_v6_send_response() doesnt use a
fake socket at all. I'll probably implement tcp_v4_send_response() to
remove these unicast_sock in linux-3.7
Reported-by: John Stultz <johnstul@us.ibm.com> Bisected-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Paul Moore <paul@paul-moore.com> Cc: Eric Paris <eparis@parisplace.org> Cc: "Serge E. Hallyn" <serge@hallyn.com> Signed-off-by: David S. Miller <davem@davemloft.net>