IR support on FusionHDTV cards is broken since kernel 2.6.31. One side
effect of the switch to the standard binding model for IR I2C devices
was to let i2c-core do the probing instead of the ir-kbd-i2c driver.
There is a slight difference between the two probe methods: i2c-core
uses 0-byte writes, while the ir-kbd-i2c was using 0-byte reads. As
some IR I2C devices only support reads, the new probe method fails to
detect them.
For now, revert to letting the driver do the probe, using 0-byte
reads. In the future, i2c-core will be extended to let callers of
i2c_new_probed_device() provide a custom probing function.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: "Timothy D. Lenz" <tlenz@vorgon.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix ULE decapsulation bug when less than 4 bytes of ULE SNDU is packed
into the remaining bytes of a MPEG2-TS frame
ULE (Unidirectional Lightweight Encapsulation RFC 4326) decapsulation
code has a bug that incorrectly treats ULE SNDU packed into the
remaining 2 or 3 bytes of a MPEG2-TS frame as having invalid pointer
field on the subsequent MPEG2-TS frame.
Signed-off-by: Ang Way Chuang <wcang@nav6.org> Acked-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a division by zero error in the irq handler.
There is a small window between the hw_params() callback and when
runtime->frame_bits is set by ALSA middle layer. When another substream is
already running, if an interrupt is delivered during that window the irq
handler calls pcm_pointer() which does a division by zero. The patch below
makes the irq handler skip substreams that are initialized but not started
yet. Cc to Clemens Ladisch because he proposed an alternate fix.
For more information, please read the original thread in the linux-kernel
mailing list: http://lkml.org/lkml/2010/2/2/187
395913d0b1db37092ea3d9d69b832183b1dd84c5 ("[CPUFREQ] remove rwsem lock
from CPUFREQ_GOV_STOP call (second call site)") is not needed, because
there is no rwsem lock in cpufreq_ondemand and cpufreq_conservative
anymore. Lock should not be released until the work done.
fix memory leak introduced by the patch 6e03a201bbe:
firmware: speed up request_firmware()
1. vfree won't release pages there were allocated explicitly and mapped
using vmap. The memory has to be vunmap-ed and the pages needs
to be freed explicitly
2. page array is moved into the 'struct
firmware' so that we can free it from release_firmware()
and not only in fw_dev_release()
The fix doesn't break the firmware load speed.
Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Ming Lei <tom.leiming@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Singed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dm9000_set_rx_csum and dm9000_hash_table are called from atomic context (in
dm9000_init_dm9000), and from non-atomic context (via ethtool_ops and
net_device_ops respectively). This causes a spinlock recursion BUG. Fix this by
renaming these functions to *_unlocked for the atomic context, and make the
original functions locking wrappers for use in the non-atomic context.
Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When operating in 1-bit mode, SDAT1 is used as dedicated interrupt line.
However, the 8686 will only drive this line when the ECSI bit is set in
the CCCR_IF register.
Thanks to Alagu Sankar for pointing me in the right direction.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Cc: Alagu Sankar <alagusankar@embwise.com> Cc: Volker Ernst <volker.ernst@txtr.com> Cc: Dan Williams <dcbw@redhat.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: Holger Schurig <hs4233@mail.mn-solutions.de> Cc: Bing Zhao <bzhao@marvell.com> Cc: libertas-dev@lists.infradead.org Cc: linux-wireless@vger.kernel.org Cc: linux-mmc@vger.kernel.org Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ACPI spec tells us that the firmware will reenable SCI_EN on resume.
Reality disagrees in some cases. The ACPI spec tells us that the only way
to set SCI_EN is via an SMM call.
https://bugzilla.kernel.org/show_bug.cgi?id=13745 shows us that doing so
may break machines. Tracing the ACPI calls made by Windows shows that it
unconditionally sets SCI_EN on resume with a direct register write, and
therefore the overwhelming probability is that everything is fine with
this behaviour.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Tested-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Len Brown <len.brown@intel.com> Cc: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that there is a bit in the _CST for Intel FFH C3
that tells the OS if we should be checking BM_STS or not.
Linux has been unconditionally checking BM_STS.
If the chip-set is configured to enable BM_STS,
it can retard or completely prevent entry into
deep C-states -- as illustrated by turbostat:
ref: Intel Processor Vendor-Specific ACPI Interface Specification
table 4 "_CST FFH GAS Field Encoding"
Bit 1: Set to 1 if OSPM should use Bus Master avoidance for this C-state
https://bugzilla.kernel.org/show_bug.cgi?id=15886
Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Save/restore MISC_ENABLE register on suspend/resume.
This fixes OOPS (invalid opcode) on resume from STR on Asus P4P800-VM,
which wakes up with MWAIT disabled.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Tested-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
futex_find_get_task is currently used (through lookup_pi_state) from two
contexts, futex_requeue and futex_lock_pi_atomic. None of the paths
looks it needs the credentials check, though. Different (e)uids
shouldn't matter at all because the only thing that is important for
shared futex is the accessibility of the shared memory.
The credentail check results in glibc assert failure or process hang (if
glibc is compiled without assert support) for shared robust pthread
mutex with priority inheritance if a process tries to lock already held
lock owned by a process with a different euid:
The problem is that futex_lock_pi_atomic which is called when we try to
lock already held lock checks the current holder (tid is stored in the
futex value) to get the PI state. It uses lookup_pi_state which in turn
gets task struct from futex_find_get_task. ESRCH is returned either
when the task is not found or if credentials check fails.
futex_lock_pi_atomic simply returns if it gets ESRCH. glibc code,
however, doesn't expect that robust lock returns with ESRCH because it
should get either success or owner died.
Signed-off-by: Michal Hocko <mhocko@suse.cz> Acked-by: Darren Hart <dvhltc@us.ibm.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Nick Piggin <npiggin@suse.de> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Marcelo Tosatti [Fri, 28 May 2010 12:44:59 +0000 (09:44 -0300)]
KVM: MMU: invalidate and flush on spte small->large page size change
Always invalidate spte and flush TLBs when changing page size, to make
sure different sized translations for the same address are never cached
in a CPU's TLB.
Currently the only case where this occurs is when a non-leaf spte pointer is
overwritten by a leaf, large spte entry. This can happen after dirty
logging is disabled on a memslot, for example.
Noticed by Andrea.
KVM-Stable-Tag Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
(cherry picked from commit 3be2264be3c00865116f997dc53ebcc90fe7fc4b)
Joerg Roedel [Mon, 17 May 2010 12:43:35 +0000 (14:43 +0200)]
KVM: SVM: Implement workaround for Erratum 383
This patch implements a workaround for AMD erratum 383 into
KVM. Without this erratum fix it is possible for a guest to
kill the host machine. This patch implements the suggested
workaround for hypervisors which will be published by the
next revision guide update.
Joerg Roedel [Mon, 17 May 2010 12:43:34 +0000 (14:43 +0200)]
KVM: SVM: Handle MCEs early in the vmexit process
This patch moves handling of the MC vmexits to an earlier
point in the vmexit. The handle_exit function is too late
because the vcpu might alreadry have changed its physical
cpu.
Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com>
(cherry picked from commit fe5913e4e1700cbfc337f4b1da9ddb26f6a55586)
Avi Kivity [Thu, 27 May 2010 11:35:58 +0000 (14:35 +0300)]
KVM: MMU: Remove user access when allowing kernel access to gpte.w=0 page
If cr0.wp=0, we have to allow the guest kernel access to a page with pte.w=0.
We do that by setting spte.w=1, since the host cr0.wp must remain set so the
host can write protect pages. Once we allow write access, we must remove
user access otherwise we mistakenly allow the user to write the page.
Reviewed-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com> Signed-off-by: Avi Kivity <avi@redhat.com>
(cherry picked from commit 69325a122580d3a7b26589e8efdd6663001c3297)
struct ethtool_rxnfc was originally defined in 2.6.27 for the
ETHTOOL_{G,S}RXFH command with only the cmd, flow_type and data
fields. It was then extended in 2.6.30 to support various additional
commands. These commands should have been defined to use a new
structure, but it is too late to change that now.
Since user-space may still be using the old structure definition
for the ETHTOOL_{G,S}RXFH commands, and since they do not need the
additional fields, only copy the originally defined fields to and
from user-space.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When an attempt is made to read the interface strings of the Artisman
Watchdog USB dongle (idVendor:idProduct 04b4:0526) an error is written
to the dmesg log (uhci_result_common: failed with status 440000) and the
dongle resets itself, resulting in a disconnect/reconnect loop.
Adding the dongle to the list of devices in quirks.c, with the same
quirk Alan Stern's previous patch for the Saitek Cyborg Gold 3D
joystick, stops the device from resetting and allows it to be used with
no problems.
Signed-off-by: Paul Mortier <mortier@btinternet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1403) is a partial reversion of an earlier change
(commit 5f677f1d45b2bf08085bbba7394392dfa586fa8e "USB: fix remote
wakeup settings during system sleep"). After hearing from a user, I
realized that remote wakeup should be enabled during system sleep
whenever userspace allows it, and not only if a driver requests it
too.
Indeed, there could be a device with no driver, that does nothing but
generate a wakeup request when the user presses a button. Such a
device should be allowed to do its job.
The problem fixed by the earlier patch -- device generating a wakeup
request for no reason, causing system suspend to abort -- was also
addressed by a later patch ("USB: don't enable remote wakeup by
default", accepted but not yet merged into mainline). The device
won't be able to generate the bogus wakeup requests because it will be
disabled for remote wakeup by default. Hence this reversion will not
re-introduce any old problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hpet_disable is called unconditionally on machine reboot if hpet support
is compiled in the kernel.
hpet_disable only checks if the machine is hpet capable but doesn't make
sure that hpet has been initialized.
[ tglx: Made it a one liner and removed the redundant hpet_address check ]
Signed-off-by: Bin Yang <bin.yang@marvell.com> Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
RealView boards with certain revisions of the L220 cache controller (ARM11*
processors only) may have issues (hardware deadlock) with the recent changes to
the mb() barrier implementation (DSB followed by an L2 cache sync). The patch
redefines the RealView ARM11MPCore mandatory barriers without the outer_sync()
call.
Tested-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Nokia RX51 board code (arch/arm/mach-omap2/board-rx51-peripherals.c)
defines a key map for the matrix keypad keyboard. The hardware seems to
use all of the 8 rows and 8 columns of the keypad, although not all
possible locations are used.
The TWL4030 supports keypads with at most 8 rows and 8 columns. Most keys
are defined with a row and column number between 0 and 7, except
which represent keycodes that should be emitted when entire row is
connected to the ground. since the driver handles this case as if we
had an extra column in the key matrix. Unfortunately we do not allocate
enough space and end up owerwriting some random memory.
Gigabyte "Spring Peak" notebook indicates wrong chassis-type, tripping up
i8042 and breaking the touchpad. Add this model to i8042_dmi_noloop_table[]
to resolve.
Sumeet Lahorani <sumeet.lahorani@oracle.com> reported that the IPoIB
child entries are world-writable; however we don't want ordinary users
to be able to create and destroy child interfaces, so fix them to be
writable only by root.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Found one x2apic system kexec loop test failed
when CONFIG_NMI_WATCHDOG=y (old) or CONFIG_LOCKUP_DETECTOR=y (current tip)
first kernel can kexec second kernel, but second kernel can not kexec third one.
it can be duplicated on another system with BIOS preenabled x2apic.
First kernel can not kexec second kernel.
It turns out, when kernel boot with pre-enabled x2apic, it will not execute
disable_local_APIC on shutdown path.
when init_apic_mappings() is called in setup_arch, it will skip setting of
apic_phys when x2apic_mode is set. ( x2apic_mode is much early check_x2apic())
Then later, disable_local_APIC() will bail out early because !apic_phys.
So check !x2apic_mode in x2apic_mode in disable_local_APIC with !apic_phys.
another solution could be updating init_apic_mappings() to set apic_phys even
for preenabled x2apic system. Actually even for x2apic system, that lapic
address is mapped already in early stage.
BTW: is there any x2apic preenabled system with apicid of boot cpu > 255?
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C3EB22B.3000701@kernel.org> Acked-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 5753c082f66eca5be81f6bda85c1718c5eea6ada ("powerpc/85xx:
Kconfig cleanup"), there is no MPC85xx Kconfig symbol anymore, so the
driver became non-selectable.
This patch fixes the issue by switching to PPC_85xx symbol.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Cc: Doug Thompson <dougthompson@xmission.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Dave Jiang <djiang@mvista.com> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
System will crash sooner or later once the memory with the code of the
s3c-sdhci.ko module is reused for something else. I really have no idea
how the lack of remove function went unnoticed into the mainline code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Warnings are treated as errors for arch/powerpc code, so build fails
with CONFIG_I2C_SPI_UCODE_PATCH=y:
CC arch/powerpc/sysdev/micropatch.o
cc1: warnings being treated as errors
arch/powerpc/sysdev/micropatch.c: In function 'cpm_load_patch':
arch/powerpc/sysdev/micropatch.c:630: warning: unused variable 'smp'
make[1]: *** [arch/powerpc/sysdev/micropatch.o] Error 1
And with CONFIG_USB_SOF_UCODE_PATCH=y:
CC arch/powerpc/sysdev/micropatch.o
cc1: warnings being treated as errors
arch/powerpc/sysdev/micropatch.c: In function 'cpm_load_patch':
arch/powerpc/sysdev/micropatch.c:629: warning: unused variable 'spp'
arch/powerpc/sysdev/micropatch.c:628: warning: unused variable 'iip'
make[1]: *** [arch/powerpc/sysdev/micropatch.o] Error 1
This patch fixes these issues by introducing proper #ifdefs.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
spi_t was removed in commit 644b2a680ccc51a9ec4d6beb12e9d47d2dee98e2
("powerpc/cpm: Remove SPI defines and spi structs"), the commit assumed
that spi_t isn't used anywhere outside of the spi_mpc8xxx driver. But
it appears that the struct is needed for micropatch code. So, let's
reintroduce the struct.
Fixes the following build issue:
CC arch/powerpc/sysdev/micropatch.o
micropatch.c: In function 'cpm_load_patch':
micropatch.c:629: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token
micropatch.c:629: error: 'spp' undeclared (first use in this function)
micropatch.c:629: error: (Each undeclared identifier is reported only once
micropatch.c:629: error: for each function it appears in.)
Reported-by: LEROY Christophe <christophe.leroy@c-s.fr> Reported-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When SPARSE_IRQ is set, irq_to_desc() can
return NULL. While the code here has a
check for NULL, it's not really correct.
Fix it by separating the check for it.
This fixes CPU hot unplug for me.
Reported-by: Alastair Bridgewater <alastair.bridgewater@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On a 32-bit machine, info.rule_cnt >= 0x40000000 leads to integer
overflow and the buffer may be smaller than needed. Since
ETHTOOL_GRXCLSRLALL is unprivileged, this can presumably be used for at
least denial of service.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For yet unknown reason, MCP89 on MBP 7,1 doesn't work w/ ahci under
linux but the controller doesn't require explicit mode setting and
works fine with ata_generic. Make ahci ignore the controller on MBP
7,1 and let ata_generic take it for now.
Reported in bko#15923.
https://bugzilla.kernel.org/show_bug.cgi?id=15923
NVIDIA is investigating why ahci mode doesn't work.
The ds1307 driver misreads the ds1388 registers when checking for 12 or 24
hour mode. Instead of checking the hour register it reads the minute
register. Therefore the driver thinks minutes >= 40 has the 12HR bit set
and resets the minute register by zeroing the high bits. This results in
minutes are reset to 0-9, jumping back in time 40 or 50 minutes. The time
jump is also written back to the RTC.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Cc: Wan ZongShun <mcuos.com@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Paul Gortmaker <p_gortmaker@yahoo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A user reported a kernel bug when running a particular program that did
the following:
created 32 threads
- each thread took a mutex, grabbed a global offset, added a buffer size
to that offset, released the lock
- read from the given offset in the file
- created a new thread to do the same
- exited
The result is that cfq's close cooperator logic would trigger, as the
threads were issuing I/O within the mean seek distance of one another.
This workload managed to routinely trigger a use after free bug when
walking the list of merge candidates for a particular cfqq
(cfqq->new_cfqq). The logic used for merging queues looks like this:
/* Avoid a circular list and skip interim queue merges */
while ((__cfqq = new_cfqq->new_cfqq)) {
if (__cfqq == cfqq)
return;
new_cfqq = __cfqq;
}
process_refs = cfqq_process_refs(cfqq);
/*
* If the process for the cfqq has gone away, there is no
* sense in merging the queues.
*/
if (process_refs == 0)
return;
/*
* Merge in the direction of the lesser amount of work.
*/
new_process_refs = cfqq_process_refs(new_cfqq);
if (new_process_refs >= process_refs) {
cfqq->new_cfqq = new_cfqq;
atomic_add(process_refs, &new_cfqq->ref);
} else {
new_cfqq->new_cfqq = cfqq;
atomic_add(new_process_refs, &cfqq->ref);
}
}
When a merge candidate is found, we add the process references for the
queue with less references to the queue with more. The actual merging
of queues happens when a new request is issued for a given cfqq. In the
case of the test program, it only does a single pread call to read in
1MB, so the actual merge never happens.
Normally, this is fine, as when the queue exits, we simply drop the
references we took on the other cfqqs in the merge chain:
/*
* If this queue was scheduled to merge with another queue, be
* sure to drop the reference taken on that queue (and others in
* the merge chain). See cfq_setup_merge and cfq_merge_cfqqs.
*/
__cfqq = cfqq->new_cfqq;
while (__cfqq) {
if (__cfqq == cfqq) {
WARN(1, "cfqq->new_cfqq loop detected\n");
break;
}
next = __cfqq->new_cfqq;
cfq_put_queue(__cfqq);
__cfqq = next;
}
However, there is a hole in this logic. Consider the following (and
keep in mind that each I/O keeps a reference to the cfqq):
q1->new_cfqq = q2 // q2 now has 2 process references
q3->new_cfqq = q2 // q2 now has 3 process references
// the process associated with q2 exits
// q2 now has 2 process references
// queue 1 exits, drops its reference on q2
// q2 now has 1 process reference
// q3 exits, so has 0 process references, and hence drops its references
// to q2, which leaves q2 also with 0 process references
q4 comes along and wants to merge with q3
q3->new_cfqq still points at q2! We follow that link and end up at an
already freed cfqq.
So, the fix is to not follow a merge chain if the top-most queue does
not have a process reference, otherwise any queue in the chain could be
already freed. I also changed the logic to disallow merging with a
queue that does not have any process references. Previously, we did
this check for one of the merge candidates, but not the other. That
doesn't really make sense.
Without the attached patch, my system would BUG within a couple of
seconds of running the reproducer program. With the patch applied, my
system ran the program for over an hour without issues.
This addresses the following bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=16217
Thanks a ton to Phil Carns for providing the bug report and an excellent
reproducer.
[ Note for stable: this applies to 2.6.32/33/34 ].
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Reported-by: Phil Carns <carns@mcs.anl.gov> Signed-off-by: Jens Axboe <jaxboe@fusionio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The set_type() function can change the chip implementation when the
trigger mode changes. That might result in using an non-initialized
irq chip when called from __setup_irq() or when called via
set_irq_type() on an already enabled irq.
The set_irq_type() function should not be called on an enabled irq,
but because we forgot to put a check into it, we have a bunch of users
which grew the habit of doing that and it never blew up as the
function is serialized via desc->lock against all users of desc->chip
and they never hit the non-initialized irq chip issue.
The easy fix for the __setup_irq() issue would be to move the
irq_chip_set_defaults(desc->chip) call after the trigger setting to
make sure that a chip change is covered.
But as we have already users, which do the type setting after
request_irq(), the safe fix for now is to call irq_chip_set_defaults()
from __irq_set_trigger() when desc->set_type() changed the irq chip.
It needs a deeper analysis whether we should refuse to change the chip
on an already enabled irq, but that'd be a large scale change to fix
all the existing users. So that's neither stable nor 2.6.35 material.
Reported-by: Esben Haabendal <eha@doredevelopment.dk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: linuxppc-dev <linuxppc-dev@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we do not use CGROUP, function update_h_load won't update h_load. When the
system has a large number of tasks far more than logical CPU number, the
incorrect cfs_rq[cpu]->h_load value will cause load_balance() to pull too
many tasks to the local CPU from the busiest CPU. So the busiest CPU keeps
going in a round robin. That will hurt performance.
The issue was found originally by a scientific calculation workload that
developed by Yanmin. With that commit, the workload performance drops
about 40%.
GCC 4.4.1 on ARM has been observed to replace the while loop in
sched_avg_update with a call to uldivmod, resulting in the
following build failure at link-time:
kernel/built-in.o: In function `sched_avg_update':
kernel/sched.c:1261: undefined reference to `__aeabi_uldivmod'
kernel/sched.c:1261: undefined reference to `__aeabi_uldivmod'
make: *** [.tmp_vmlinux1] Error 1
This patch introduces a fake data hazard to the loop body to
prevent the compiler optimising the loop away.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The x3950 family can have as many as 256 PCI buses in a single system, so
change the limits to the maximum. Since there can only be 256 PCI buses in one
domain, we no longer need the BUG_ON check.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
LKML-Reference: <20100701004519.GQ15515@tux1.beaverton.ibm.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Newer systems (x3950M2) can have 48 PHBs per chassis and 8
chassis, so bump the limits up and provide an explanation
of the requirements for each class.
Before we had a generic breakpoint layer, x86 used to send a
sigtrap for any debug event that happened in userspace,
except if it was caused by lazy dr7 switches.
Currently we only send such signal for single step or breakpoint
events.
However, there are three other kind of debug exceptions:
- debug register access detected: trigger an exception if the
next instruction touches the debug registers. We don't use
it.
- task switch, but we don't use tss.
- icebp/int01 trap. This instruction (0xf1) is undocumented and
generates an int 1 exception. Unlike single step through TF
flag, it doesn't set the single step origin of the exception
in dr6.
icebp then used to be reported in userspace using trap signals
but this have been incidentally broken with the new breakpoint
code. Reenable this. Since this is the only debug event that
doesn't set anything in dr6, this is all we have to check.
This fixes a regression in Wine where World Of Warcraft got broken
as it uses this for software protection checks purposes. And
probably other apps do.
Reported-and-tested-by: Alexandre Julliard <julliard@winehq.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Prasad <prasad@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When calculating the DCT channel from the syndrome we need to know the
syndrome type (x4 vs x8). On F10h, this is read out from extended PCI
cfg space register F3x180 while on K8 we only support x4 syndromes and
don't have extended PCI config space anyway.
Make the code accessing F3x180 F10h only and fall back to x4 syndromes
on everything else.
The current initialisation code probes 'unsupported' AGP devices
simply by calling its own probe function. It does not lock these
devices or even check whether another driver is already bound to
them.
We must use the device core to manage this. So if the specific
device id table didn't match anything and agp_try_unsupported=1,
switch the device id table and call driver_attach() again.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Such NULL pointer dereference can occur when the driver was fixing the
read errors/bad blocks and the disk was physically removed
causing a system crash. This patch check if the
rcu_dereference() returns valid rdev before accessing it in fix_read_error().
Signed-off-by: Prasanna S. Panchamukhi <prasanna.panchamukhi@riverbed.com> Signed-off-by: Rob Becker <rbecker@riverbed.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The addition of TLLAO option created a kernel OOPS regression
for the case where neighbor advertisement is being sent via
proxy path. When using proxy, ipv6_get_ifaddr() returns NULL
causing the NULL dereference.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code that hashes and unhashes connections from the connection table
is missing locking of the connection being modified, which opens up a
race condition and results in memory corruption when this race condition
is hit.
Here is what happens in pretty verbose form:
CPU 0 CPU 1
------------ ------------
An active connection is terminated and
we schedule ip_vs_conn_expire() on this
CPU to expire this connection.
IRQ assignment is changed to this CPU,
but the expire timer stays scheduled on
the other CPU.
New connection from same ip:port comes
in right before the timer expires, we
find the inactive connection in our
connection table and get a reference to
it. We proper lock the connection in
tcp_state_transition() and read the
connection flags in set_tcp_state().
ip_vs_conn_expire() gets called, we
unhash the connection from our
connection table and remove the hashed
flag in ip_vs_conn_unhash(), without
proper locking!
While still holding proper locks we
write the connection flags in
set_tcp_state() and this sets the hashed
flag again.
ip_vs_conn_expire() fails to expire the
connection, because the other CPU has
incremented the reference count. We try
to re-insert the connection into our
connection table, but this fails in
ip_vs_conn_hash(), because the hashed
flag has been set by the other CPU. We
re-schedule execution of
ip_vs_conn_expire(). Now this connection
has the hashed flag set, but isn't
actually hashed in our connection table
and has a dangling list_head.
We drop the reference we held on the
connection and schedule the expire timer
for timeouting the connection on this
CPU. Further packets won't be able to
find this connection in our connection
table.
ip_vs_conn_expire() gets called again,
we think it's already hashed, but the
list_head is dangling and while removing
the connection from our connection table
we write to the memory location where
this list_head points to.
The result will probably be a kernel oops at some other point in time.
This race condition is pretty subtle, but it can be triggered remotely.
It needs the IRQ assignment change or another circumstance where packets
coming from the same ip:port for the same service are being processed on
different CPUs. And it involves hitting the exact time at which
ip_vs_conn_expire() gets called. It can be avoided by making sure that
all packets from one connection are always processed on the same CPU and
can be made harder to exploit by changing the connection timeouts to
some custom values.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix subsequent suspends by issuing tpm_continue_selftest during resume.
Otherwise, the tpm chip seems to be not fully initialized and will reject
the save state command during suspend, thus preventing the whole system
to suspend.
You generally have two cases where DDC lines are shared:
- HDMI + VGA
- HDMI + DVI-D
HDMI + VGA is easy to deal with because you can check the EDID for the
to see if the attached monitor is digital. A shared DDC line with two
digital connectors is more complex. You can't use the hdmi bits in the
EDID since they may not be there with DVI<->HDMI adapters. In this case
all we can do is check the HPD pins to see which is connected as we have
no way of knowing using the EDID.
Reported-by: trapdoor6@gmail.com Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Code did not handle projected 2d and depth coordinates, meaning potentially
set 3d or cube special handling might stick.
(Not sure what depth coord actually does, but I guess handling it
like a normal coordinate is the right thing to do.)
Might be related to https://bugs.freedesktop.org/show_bug.cgi?id=26428
Signed-off-by: sroland@vmware.com Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes an Ironlake laptop with a 68.940MHz 1280x800 panel and 120MHz SSC
reference clock.
More generally, the 0.488% tolerance used before is just too tight to
reliably find a PLL setting. I extracted the search algorithm and
modified it to find the dot clocks with maximum error over the valid
range for the given output type:
A lot of 945GMs have had stability issues for a long time, this manifested as X hangs, blitter engine hangs, and lots of crashes.
one such report is at:
https://bugs.freedesktop.org/show_bug.cgi?id=20560
along with numerous distro bugzillas.
This only took a week of digging and hair ripping to figure out.
Tracked down and tested on a 945GM Lenovo T60,
previously running
x11perf -copypixwin500
or
x11perf -copywinpix500
repeatedly would cause the GPU to wedge within 4 or 5 tries, with random busy bits set.
After this patch no hangs were observed.
Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hibernate issues that got fixed in commit 985b823b9192 ("drm/i915:
fix hibernation since i915 self-reclaim fixes") turn out to have been
incomplete. Vefa Bicakci tested lots of hibernate cycles, and without
the __GFP_RECLAIMABLE flag the system eventually fails to resume.
With the flag added, Vefa can apparently hibernate forever (or until he
gets bored running his automated scripts, whichever comes first).
The reclaimable flag was there originally, and was one of the flags that
were dropped (unintentionally) by commit 4bdadb978569 ("drm/i915:
Selectively enable self-reclaim") that introduced all these problems,
but I didn't want to just blindly add back all the flags in commit 985b823b9192, and it looked like __GFP_RECLAIM wasn't necessary. It
clearly was.
I still suspect that there is some subtle reason we're missing that
causes the problems, but __GFP_RECLAIMABLE is certainly not wrong to use
in this context, and is what the code historically used. And we have no
idea what the causes the corruption without it.
Reported-and-tested-by: M. Vefa Bicakci <bicave@superonline.com> Cc: Dave Airlie <airlied@gmail.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 4bdadb9785696439c6e2b3efe34aa76df1149c83 ("drm/i915:
Selectively enable self-reclaim"), we've been passing GFP_MOVABLE to the
i915 page allocator where we weren't before due to some over-eager
removal of the page mapping gfp_flags games the code used to play.
This caused hibernate on Intel hardware to result in a lot of memory
corruptions on resume. See for example
http://bugzilla.kernel.org/show_bug.cgi?id=13811
Reported-by: Evengi Golov (in bugzilla) Signed-off-by: Dave Airlie <airlied@redhat.com> Tested-by: M. Vefa Bicakci <bicave@superonline.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the call to ddebug_remove_module() down into free_module(). In this
way it should be called from all error paths. Currently, we are missing
the remove if the module init routine fails.
Signed-off-by: Jason Baron <jbaron@redhat.com> Reported-by: Thomas Renninger <trenn@suse.de> Tested-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1. The BTRFS_IOC_CLONE and BTRFS_IOC_CLONE_RANGE ioctls should check
whether the donor file is append-only before writing to it.
2. The BTRFS_IOC_CLONE_RANGE ioctl appears to have an integer
overflow that allows a user to specify an out-of-bounds range to copy
from the source file (if off + len wraps around). I haven't been able
to successfully exploit this, but I'd imagine that a clever attacker
could use this to read things he shouldn't. Even if it's not
exploitable, it couldn't hurt to be safe.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com> Signed-off-by: Chris Mason <chris.mason@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
changes:
v2 Added missing break (Johannes)
v3 Broke original patch into two (Johannes)
Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a missing element of the ReadPubEK command output,
that prevents future overflow of this buffer when copying the
TPM output result into it.
Prevents a kernel panic in case the user tries to read the
pubek from sysfs.
Use an irq spinlock to hold off the IRQ handler until
enough early card init is complete such that the handler
can run without faulting.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If bit 29 is set, MAC H/W can attempt to decrypt the received aggregate
with WEP or TKIP, eventhough the received frame may be a CRC failed
corrupted frame. If this bit is set, H/W obeys key type in keycache.
If it is not set and if the key type in keycache is neither open nor
AES, H/W forces key type to be open. But bit 29 should be set to 1
for AsyncFIFO feature to encrypt/decrypt the aggregate with WEP or TKIP.
Reported-by: Johan Hovold <johan.hovold@lundinova.se> Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: Ranga Rao Ravuri <ranga.ravuri@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jumbo frames are not supported, and if they are seen it is likely
a bogus frame so just silently discard them instead of warning on
them all time. Also, instead of dropping them immediately though
move the check *after* we check for all sort of frame errors. This
should enable us to discard these frames if the hardware picks
other bogus items first. Lets see if we still get those jumbo
counters increasing still with this.
Jumbo frames would happen if we tell hardware we can support
a small 802.11 chunks of DMA'd frame, hardware would split RX'd
frames into parts and we'd have to reconstruct them in software.
This is done with USB due to the bulk size but with ath5k we
already provide a good limit to hardware and this should not be
happening.
This is reported quite often and if it fills the logs then this
needs to be addressed and to avoid spurious reports.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the attempt to read the calldir fails, then instead of storing the read
bytes, we currently discard them. This leads to a garbage final result when
upon re-entry to the same routine, we read the remaining bytes.
Fixes the regression in bugzilla number 16213. Please see
https://bugzilla.kernel.org/show_bug.cgi?id=16213
When ide taskfile access is being used (for example with hdparm --security
commands) and cfq scheduler is selected, the scheduler crashes on BUG in
cfq_put_request.
The reason is that the cfq scheduler is tracking counts of read and write
requests separately; the ide-taskfile subsystem allocates a read request and
then flips the flag to make it a write request. The counters in cfq will
mismatch.
This patch changes ide-taskfile to allocate the READ or WRITE request as
required and don't change the flag later.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When implementing the test_iqr() method, I forgot that this driver is not an
ordinary PCI driver and also needs to support VLB variant of the chip. Moreover,
'hwif->dev' should be NULL, potentially causing oops in pci_read_config_byte().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The kernel's math-emu code contains a macro _FP_FROM_INT() which is
used to convert an integer to a raw normalized floating-point value.
It does this basically in three steps:
1. Compute the exponent from the number of leading zero bits.
2. Downshift large fractions to put the MSB in the right position
for normalized fractions.
3. Upshift small fractions to put the MSB in the right position.
There is an boundary error in step 2, causing a fraction with its
MSB exactly one bit above the normalized MSB position to not be
downshifted. This results in a non-normalized raw float, which when
packed becomes a massively inaccurate representation for that input.
The impact of this depends on a number of arch-specific factors,
but it is known to have broken emulation of FXTOD instructions
on UltraSPARC III, which was originally reported as GCC bug 44631
<http://gcc.gnu.org/bugzilla/show_bug.cgi?id=44631>.
Any arch which uses math-emu to emulate conversions from integers to
same-size floats may be affected.
The fix is simple: the exponent comparison used to determine if the
fraction should be downshifted must be "<=" not "<".
I'm sending a kernel module to test this as a reply to this message.
There are also SPARC user-space test cases in the GCC bug entry.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When configuring DMVPN (GRE + openNHRP) and a GRE remote
address is configured a kernel Oops is observed. The
obserseved Oops is caused by a NULL header_ops pointer
(neigh->dev->header_ops) in neigh_update_hhs() when
is executed. The dev associated with the NULL header_ops is
the GRE interface. This patch guards against the
possibility that header_ops is NULL.
This Oops was first observed in kernel version 2.6.26.8.
Signed-off-by: Doug Kehn <rdkehn@yahoo.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It can happen that there are no packets in queue while calling
tcp_xmit_retransmit_queue(). tcp_write_queue_head() then returns
NULL and that gets deref'ed to get sacked into a local var.
There is no work to do if no packets are outstanding so we just
exit early.
This oops was introduced by 08ebd1721ab8fd (tcp: remove tp->lost_out
guard to make joining diff nicer).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Reported-by: Lennart Schulte <lennart.schulte@nets.rwth-aachen.de> Tested-by: Lennart Schulte <lennart.schulte@nets.rwth-aachen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix problem in reading the tx_queue recorded in a socket. In
dev_pick_tx, the TX queue is read by doing a check with
sk_tx_queue_recorded on the socket, followed by a sk_tx_queue_get.
The problem is that there is not mutual exclusion across these
calls in the socket so it it is possible that the queue in the
sock can be invalidated after sk_tx_queue_recorded is called so
that sk_tx_queue get returns -1, which sets 65535 in queue_index
and thus dev_pick_tx returns 65536 which is a bogus queue and
can cause crash in dev_queue_xmit.
We fix this by only calling sk_tx_queue_get which does the proper
checks. The interface is that sk_tx_queue_get returns the TX queue
if the sock argument is non-NULL and TX queue is recorded, else it
returns -1. sk_tx_queue_recorded is no longer used so it can be
completely removed.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.
However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:
$ ethtool -r eth0
$ ethtool -A eth0 autoneg off
Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: Brandon Philips <bphilips@suse.de> Tested-by: Brandon Philips <bphilips@suse.de> Cc: stable@kernel.org Tested-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log