Matthew Vick [Fri, 16 Mar 2012 09:03:01 +0000 (09:03 +0000)]
e1000e: Minor comment clean-up.
Move the first phrase of a multi-line comment to the second line.
Signed-off-by: Matthew Vick <matthew.vick@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ben Greear [Wed, 4 Apr 2012 06:01:29 +0000 (06:01 +0000)]
e1000: Support RX-ALL flag.
This allows the NIC to receive errored frames (bad FCS, etc)
and pass them up the stack. This can be useful when using
sniffers.
Signed-off-by: Ben Greear <greearb@candelatech.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The congestion management code has migrated into a common location,
allowing all fw writes controlling mf congestion to be made in a
single function in the code. This is a semantic change.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Restore remote-faule detection, which periodically checks for
remote-fault on the MAC layer. In case physical link appear to be
up but fault is set, it will provide a link down indication, and
when the fault is cleared, it will indicate link up again.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: added support for working with one msix irq.
Until now, the bnx2x driver needed at least 2 available msix interrupt
vectors in order to use msix. This patch add the possibility of configuring
msix when only one interrupt vector is available.
Notice this patch contains lines with over 80 characters, as it keeps print
strings in a single line.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
During boot-from-SAN, if msix interrupts are unavailable and inta
is requested, it is possible that inta would be disabled in the
pci bus. This patch enables inta when requested.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Removed uninformative debug prints, as well as two functions
which were hardly used in the code.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Mon, 2 Apr 2012 22:47:16 +0000 (22:47 +0000)]
ppp: use for_each_set_bit_from
Use for_each_set_bit_from to iterate over all the set bit in a memory
region.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Dmitry Kozlov <xeb@mail.ru> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 27 Mar 2012 13:20:45 +0000 (13:20 +0000)]
net/hyperv: Add flow control based on hi/low watermark
In the existing code, we only stop queue when the ringbuffer is full,
so the current packet has to be dropped or retried from upper layer.
This patch stops the tx queue when available ringbuffer is below
the low watermark. So the ringbuffer still has small amount of space
available for the current packet. This will reduce the overhead of
retries on sending.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lino Sanfilippo [Fri, 30 Mar 2012 07:36:16 +0000 (07:36 +0000)]
sky2: fix missing register reset on error path in sky2_test_msi()
In sky2_test_msi() the temporarily set SW IRQ in B0 register is not reset in case
that request_irq() fails.
With this patch we only set the interrupt mask if request_irq() was successful.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 3 Apr 2012 05:28:28 +0000 (05:28 +0000)]
af_unix: reduce high order page allocations
unix_dgram_sendmsg() currently builds linear skbs, and this can stress
page allocator with high order page allocations. When memory gets
fragmented, this can eventually fail.
We can try to use order-2 allocations for skb head (SKB_MAX_ALLOC) plus
up to 16 page fragments to lower pressure on buddy allocator.
This patch has no effect on messages of less than 16064 bytes.
(on 64bit arches with PAGE_SIZE=4096)
For bigger messages (from 16065 to 81600 bytes), this patch brings
reliability at the expense of performance penalty because of extra pages
allocations.
Ben Greear [Thu, 29 Mar 2012 12:51:30 +0000 (12:51 +0000)]
net: Report dev->promiscuity in netlink reports.
The standard ways of probing a device's promiscuity
(ifi_flags, for instance) does not report the actual
state of the device. This patch adds dev->promiscuity
to the netlink netdevice report so that users can know
for certain if the device is acting PROMISC or not.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/addrconf.c:340: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
net/ipv6/addrconf.c:342: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:444: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:1337: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
net/ipv6/addrconf.c:1526: ERROR: "(foo*)" should be "(foo *)"
net/ipv6/addrconf.c:1671: ERROR: open brace '{' following function declarations go on the next line
net/ipv6/addrconf.c:1914: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2368: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2370: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2416: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2437: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2573: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:3797: ERROR: "foo* bar" should be "foo *bar"
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Signed-off-by: David S. Miller <davem@davemloft.net>
icmp.c:501: ERROR: "(foo*)" should be "(foo *)"
icmp.c:582: ERROR: "(foo*)" should be "(foo *)"
icmp.c:954: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Signed-off-by: David S. Miller <davem@davemloft.net>
exthdrs_core.c:113: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
exthdrs_core.c:114: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Signed-off-by: David S. Miller <davem@davemloft.net>
exthdrs.c:726: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
exthdrs.c:741: ERROR: "(foo*)" should be "(foo *)"
exthdrs.c:741: ERROR: "(foo*)" should be "(foo *)"
exthdrs.c:744: ERROR: "(foo**)" should be "(foo **)"
exthdrs.c:746: ERROR: "(foo**)" should be "(foo **)"
exthdrs.c:748: ERROR: "(foo**)" should be "(foo **)"
exthdrs.c:750: ERROR: "(foo**)" should be "(foo **)"
exthdrs.c:755: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
exthdrs.c:896: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Signed-off-by: David S. Miller <davem@davemloft.net>
datagram.c:101: ERROR: "(foo*)" should be "(foo *)"
datagram.c:521: ERROR: space required before the open parenthesis '('
datagram.c:830: WARNING: braces {} are not necessary for single statement blocks
datagram.c:849: WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Eldad Zack <eldad@fogrefinery.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
In IPv4, if an RTA_IIF attribute is specified within an RTM_GETROUTE
message, then a route is searched as if a packet was received on the
specified 'iif' interface.
However in IPv6, RTA_IIF is not interpreted in the same way:
'inet6_rtm_getroute()' always calls 'ip6_route_output()', regardless the
RTA_IIF attribute.
As a result, in IPv6 there's no way to use RTM_GETROUTE in order to look
for a route as if a packet was received on a specific interface.
Fix 'inet6_rtm_getroute()' so that RTA_IIF is interpreted as "lookup a
route as if a packet was received on the specified interface", similar
to IPv4's 'inet_rtm_getroute()' interpretation.
Reported-by: Ami Koren <amikoren@yahoo.com> Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stigge@antcom.de [Wed, 28 Mar 2012 12:36:26 +0000 (12:36 +0000)]
net: lpc_eth: Fix rename of dev_hw_addr_random
In parallel to the integration of lpc_eth.c, dev_hw_addr_random() has been
renamed to eth_hw_addr_random(). This patch fixes it also in the new driver
lpc_eth.c.
Signed-off-by: Roland Stigge <stigge@antcom.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton [Wed, 28 Mar 2012 12:10:57 +0000 (12:10 +0000)]
net/netfilter/nfnetlink_acct.c: use linux/atomic.h
There's no known problem here, but this is one of only two non-arch files
in the kernel which use asm/atomic.h instead of linux/atomic.h.
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Cc: Patrick McHardy <kaber@trash.net> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
If both addresses equal, nothing needs to be done. If the device is down,
then we simply copy the new address to dev->dev_addr. If the device is up,
then we add another loopback device with the new address, and if that does
not fail, we remove the loopback device with the old address. And only
then, we update the dev->dev_addr.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Kenth Eriksson [Tue, 27 Mar 2012 22:05:54 +0000 (22:05 +0000)]
Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
The merge done in commit b26e478f undid bug fix in commit c3e072f8
("net: fsl_pq_mdio: fix non tbi phy access"), with the result that non
TBI (e.g. MDIO) PHYs cannot be accessed.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ward [Tue, 27 Mar 2012 09:01:52 +0000 (09:01 +0000)]
net/garp: avoid infinite loop if attribute already exists
An infinite loop occurred if garp_attr_create was called with the values
of an existing attribute. This might happen if a previous leave request
for the attribute has not yet been followed by a PDU transmission (or,
if the application previously issued a join request for the attribute
and is now issuing another one, without having issued a leave request).
If garp_attr_create finds an existing attribute having the same values,
return the address to it. Its state will then get updated (i.e., if it
was in a leaving state, it will move into a non-leaving state and not
get deleted during the next PDU transmission).
To accomplish this fix, collapse garp_attr_insert into garp_attr_create
(which is its only caller).
Thanks to Jorge Boncompte [DTI2] <jorge@dti2.net> for contributing to
this fix.
Signed-off-by: David Ward <david.ward@ll.mit.edu> Acked-by: Jorge Boncompte [DTI2] <jorge@dti2.net> Signed-off-by: David S. Miller <davem@davemloft.net>
x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
When K >= 0xFFFF0000, AND needs the two least significant bytes of K as
its operand, but EMIT2() gives it the least significant byte of K and
0x2. EMIT() should be used here to replace EMIT2().
Signed-off-by: Feiran Zhuang <zhuangfeiran@ict.ac.cn> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Weiping Pan [Tue, 27 Mar 2012 19:18:24 +0000 (19:18 +0000)]
bonding: emit event when bonding changes MAC
When a bonding device is configured with fail_over_mac=active,
we expect to see the MAC address of the new active slave as the source MAC
address after failover. But we see that the source MAC address is the MAC
address of previous active slave.
Emit NETDEV_CHANGEADDR event when bonding changes its MAC address, in order
to let arp_netdev_event flush neighbour cache and route cache.
1 on hostB,
modprobe bonding mode=1 miimon=500 fail_over_mac=active downdelay=1000
num_grat_arp=1
ifconfig bond0 192.168.100.2/24 up
ifenslave bond0 eth0
ifenslave bond0 eth1
then eth0 is the active slave, and MAC of bond0 is MAC of eth0.
2 on hostA, ping 192.168.100.2
3 on hostB,
tcpdump -i bond0 -p icmp -XXX
you will see bond0 uses MAC of eth0 as source MAC in icmp reply.
4 on hostB,
ifconfig eth0 down
tcpdump -i bond0 -p icmp -XXX (just keep it running in step 3)
you will see first bond0 uses MAC of eth1 as source MAC in icmp
reply, then it will use MAC of eth0 as source MAC.
Signed-off-by: Weiping Pan <wpan@redhat.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever the station informs the AP that it is about to leave the
operating channel, the timestamp should be recorded. It is handled
in scan resume but not in scan start. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 27 Mar 2012 04:38:55 +0000 (10:08 +0530)]
ath9k: Use HW HT capabilites properly
The commit "ath9k: Remove aggregation flags" changed how
nodes were being initialized. Use the HW HT cap bits
to initialize/de-initialize nodes, else we would be
accessing an uninitialized entry during a suspend/resume cycle,
resulting in a panic.
Reported-by: Justin P. Mattock <justinmattock@gmail.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Benjamin LaHaise [Tue, 27 Mar 2012 15:55:44 +0000 (15:55 +0000)]
net/core: dev_forward_skb() should clear skb_iif
While investigating another bug, I found that the code on the incoming path
in __netif_receive_skb will only set skb->skb_iif if it is already 0. When
dev_forward_skb() is used in the case of interfaces like veth, skb_iif may
already have been set. Making dev_forward_skb() cause the packet to look
like a newly received packet would seem to the the correct behaviour here,
as otherwise the wrong incoming interface can be reported for such a packet.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin LaHaise [Tue, 27 Mar 2012 15:55:32 +0000 (15:55 +0000)]
net/ipv4: fix IPv4 multicast over network namespaces
When using multicast over a local bridge feeding a number of LXC guests
using veth, the LXC guests are unable to get a response from other guests
when pinging 224.0.0.1. Multicast packets did not appear to be getting
delivered to the network namespaces of the guest hosts, and further
inspection showed that the incoming route was pointing to the loopback
device of the host, not the guest. This lead to the wrong network namespace
being picked up by sockets (like ICMP). Fix this by using the correct
network namespace when creating the inbound route entry.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Jones [Tue, 27 Mar 2012 07:28:09 +0000 (07:28 +0000)]
virtio_net: do not rate limit counter increments
While it is desirable to rate limit certain messages, it is not
desirable to rate limit the incrementing of counters associated
with those messages.
Signed-off-by: Rick Jones <rick.jones2@hp.com> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log