Axel Lin [Mon, 18 Jun 2012 02:11:28 +0000 (10:11 +0800)]
regulator: core: Support table based mapping in regulator_set_voltage_time_sel
For table based mapping, we can calculate voltage difference by below equation:
abs(rdev->desc->volt_table[new_selector] - rdev->desc->volt_table[old_selector])
Thus we can make regulator_set_voltage_time_sel work for table based mapping.
regulator_set_voltage_time_sel() only supports linear or table based mapping.
In case it is misused, also warn if neither linear nor table based mapping
is used with regulator_set_voltage_time_sel().
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator: Add ramp_delay configuration to constraints
For some hardwares ramp_delay for BUCKs is a configurable parameter which can
be configured through DT or board file.This patch adds ramp_delay to regulator
constraints and allow user to configure it for regulators which supports this
feature, through DT or board file. It will provide two ways of setting the
ramp_delay for a regulator:
First, by setting it as constraints in board file(for configurable
regulators) and set_machine_constraints() will take care of setting it on
hardware by calling(the provided) .set_ramp_delay() operation(callback).
Second, by setting it as data in regulator_desc(as fixed/default
ramp_delay rate) for a regulator in driver.
regulator_set_voltage_time_sel() will give preference to
constraints->ramp_delay while reading ramp_delay rate for regulator. Similarly
users should also take care accordingly while refering ramp_delay rate(in case
of implementing their private .set_voltage_time_sel() callbacks for different
regulators).
[Rewrote subject for 80 columns -- broonie]
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Fri, 8 Jun 2012 02:29:21 +0000 (10:29 +0800)]
regulator: ab8500: Remove min_uV and max_uV from struct ab8500_regulator_info
The min_uV and max_uV are not really used in the code and misleading because
the min_uV and max_uV settings does not match the value in the voltage table.
Axel Lin [Fri, 8 Jun 2012 02:27:49 +0000 (10:27 +0800)]
regulator: ab8500: Use regulator_list_voltage_linear for ab8500_regulator_fixed_ops
Also removes set_voltage_time_sel callback from ab8500_regulator_fixed_ops
because the voltage won't change. ( And ab8500_regulator_fixed_ops does not
implement get_voltage_sel so set_voltage_time_sel won't be called )
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 12 Jun 2012 12:08:30 +0000 (20:08 +0800)]
regulator: wm8350: Use wm8350_ldo_list_voltage instead of open code to verify selected voltage
Call wm8350_ldo_list_voltage() instead of open code to verify selected voltage
falls within specified range.
Use wm8350_ldo_list_voltage() here is less error prone.
wm8350_ldo_val_to_mvolts() is only used in wm8350_ldo_list_voltage now, so
remove it and move the implementation to wm8350_ldo_list_voltage().
This patch also include below small changes in wm8350_ldo_map_voltage:
1. wm8350_ldo_map_voltage() returns selector, thus rename variable mV to sel.
2. Use DIV_ROUND_UP macro to calculate selector.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Wed, 13 Jun 2012 03:27:11 +0000 (11:27 +0800)]
regulator: tps65217: Convert to regulator_[is_enabled|get_voltage_sel]_regmap
This patch converts .is_enabled and .get_voltage_sel to
regulator_is_enabled_regmap and regulator_get_voltage_sel_regmap.
For .enable, .disable, and .set_voltage_sel, the write protect level is either
1 or 2. So we cannot use regulator_[enable|disable|set_voltage_sel]_regmap.
Now we store the enable reg/mask and vsel reg/mask in regulator_desc,
so we can remove enable_mask, set_vout_reg, and set_vout_mask from
struct tps_info.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 12 Jun 2012 08:36:20 +0000 (16:36 +0800)]
regulator: wm8400: Adjust the equation for selector >= 15 in wm8400_ldo_list_voltage
Adjust the equation for selector >= 15 for better readability.
The equation "1700000 + ((selector - 15) * 100000)" can be interpreted by:
Starting from selector 15: Steps of 100mV from 1700mV
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 12 Jun 2012 08:34:55 +0000 (16:34 +0800)]
regulator: wm8400: Use wm8400_ldo_list_voltage instead of open code to verify selected voltage
Call wm8400_ldo_list_voltage() instead of open code to verify selected voltage
falls within specified range.
Use wm8400_ldo_list_voltage() here is less error prone.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Fri, 8 Jun 2012 09:21:44 +0000 (17:21 +0800)]
regulator: max77686: Fix the delay time for set_voltage_time_sel
rdev->desc->uV_step * abs(new_selector - old_selector) returns uV.
The unit of ramp_rate is mV/us.
Thus 1000 should be multiplied.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator: core: Add regulator_set_voltage_time_sel to calculate ramp delay.
This patch adds regulator_set_voltage_time_sel(), to move into core, the
commonly used code by drivers to provide the .set_voltage_time_sel callback.
It will also allow us to configure different ramp delay for different
regulators easily.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 5 Jun 2012 14:52:06 +0000 (22:52 +0800)]
regulator: tps6586x: Convert to regulator_list_voltage_table
Also adds tps6586x_ldo0_voltages mapping table for LDO0, so we can remove the
hack in tps6586x_list_voltage() and convert it to regulator_list_voltage_table.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Wed, 6 Jun 2012 12:01:38 +0000 (20:01 +0800)]
regulator: palmas: Slightly code change for better readability
It's a little bit hard to read that the "else" case means id == PALMAS_REG_SMPS10.
if (id != PALMAS_REG_SMPS10){
do something for the cases id != PALMAS_REG_SMPS10;
} else {
do something for the case id == PALMAS_REG_SMPS10;
}
This patch changes above syntax to switch statement.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Graeme Gregory <gg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 7 Jun 2012 09:08:21 +0000 (17:08 +0800)]
regulator: palmas: Clear PALMAS_SMPS12_CTRL_MODE_ACTIVE_MASK bits in palmas_set_mode_smps
Current code actually clears more bits than PALMAS_SMPS12_CTRL_MODE_ACTIVE_MASK bits.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Graeme Gregory <gg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 7 Jun 2012 02:38:30 +0000 (10:38 +0800)]
regulator: da903x: Don't read/write to DA9030_INVAL/DA9034_INVAL address
For fixed voltage, DA9030_LDO13 and DA9034_LDO5, the info->vol_reg is
DA9030_INVAL/DA9034_INVAL.
It does not make sense to read/write to DA9030_INVAL/DA9034_INVAL address.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 5 Jun 2012 00:58:13 +0000 (08:58 +0800)]
regulator: tps6507x: Avoid duplicating the same mapping table for LDO2 and VDCDCx
The voltage mapping table for LDO2 is exactly the same as VDCDCx.
Thus we can use one mapping table for both LDO2 and VDCDCx instead of
duplicating the mapping table.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 5 Jun 2012 00:39:52 +0000 (08:39 +0800)]
regulator: tps6507x: Remove unused min_uV and max_uV from struct tps_info
The min_uV and max_uV are not used in this driver.
For table based voltage mappings, we can get min_uV and max_uV by
info->table[0] and info->table[table_len -1].
Thus remove min_uV and max_uV from struct tps_info.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Mon, 4 Jun 2012 02:19:18 +0000 (10:19 +0800)]
regulator: max77686: Fix checkpatch warnings
Fix below checkpatch warnings:
$ scripts/checkpatch.pl -f drivers/regulator/max77686.c
ERROR: return is not a function, parentheses are not required
+ return (DIV_ROUND_UP(rdev->desc->uV_step
WARNING: line over 80 characters
+ .ops = &max77686_buck_dvs_ops, \
total: 1 errors, 1 warnings, 339 lines checked
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sun, 3 Jun 2012 14:46:14 +0000 (22:46 +0800)]
regulator: max77686: Use regulator_map_voltage_linear for simple linear mappings
Both max77686_ops and max77686_buck_dvs_ops use simple linear voltage maps.
Thus use regulator_map_voltage_linear is more efficient than using the defult
regulator_map_voltage_iterate.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sun, 3 Jun 2012 15:12:16 +0000 (23:12 +0800)]
regulator: wm8350: Use regulator_map_voltage_linear for wm8350_dcdc_ops
wm8350_dcdc_ops uses simple linear voltage maps.
Thus use regulator_map_voltage_linear is more efficient than using the default
regulator_map_voltage_iterate.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Wed, 30 May 2012 04:47:27 +0000 (12:47 +0800)]
regulator: Change db8500-prcmu match names to reflect Device Tree
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the db8500-prcum regulator driver so
this is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Wed, 30 May 2012 04:47:26 +0000 (12:47 +0800)]
regulator: Change ab8500 match names to reflect Device Tree
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the ab8500 regulator driver so this
is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add driver for support max77686 regulator.
MAX77686 provides LDOs[1~26] and BUCKs[1~9]. It support to set or get the
volatege of regulator on max77686 chip with using regmap.
Signed-off-by: Chiwoong Byun <woong.byun@samsung.com> Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com> Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 31 May 2012 09:40:22 +0000 (17:40 +0800)]
regulator: wm8400: Use regulator_map_voltage_linear for wm8400_dcdc_ops
wm8400_dcdc_ops uses simple linear voltage maps.
Thus use regulator_map_voltage_linear is more efficient than using the default
regulator_map_voltage_iterate.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 31 May 2012 09:39:00 +0000 (17:39 +0800)]
regulator: wm831x-ldo: Use regulator_map_voltage_linear for wm831x_alive_ldo_ops
wm831x_alive_ldo_ops uses simple linear voltage maps.
Thus use regulator_map_voltage_linear is more efficient than using the default
regulator_map_voltage_iterate.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 22 May 2012 04:26:42 +0000 (12:26 +0800)]
regulator: palmas: Use regulator_[list|map]_voltage_linear() for palmas_ops_smps10
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Graeme Gregory <gg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 9 May 2012 21:22:30 +0000 (22:22 +0100)]
regulator: wm8350: Convert DCDCs to set_voltage_sel() and linear voltages
The WM8350 DCDCs have a simple linear mapping from selectors to voltages
so can be converted very simply to use the new infrastructure for a nice
reduction in code size.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Mon, 21 May 2012 01:39:08 +0000 (09:39 +0800)]
regulator: ab8500: Let regulator core handle the case no delay for setting new voltage if regulator is off
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sun, 20 May 2012 02:37:33 +0000 (10:37 +0800)]
regulator: tps6105x: Use regulator_list_voltage_table()
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sun, 20 May 2012 02:33:35 +0000 (10:33 +0800)]
regulator: ab8500: Use regulator_list_voltage_table()
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sun, 20 May 2012 02:31:58 +0000 (10:31 +0800)]
regulator: ab3100: Use regulator_list_voltage_table()
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 8 May 2012 17:10:45 +0000 (18:10 +0100)]
regulator: core: Use dev_get_regmap() to find the regmap
If no regmap is explicitly specified then use dev_get_regmap() to obtain
one. The driver must explicitly enable any actual usage of the regmap
so there's no concern with unwanted usage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
Axel Lin [Mon, 21 May 2012 01:37:52 +0000 (09:37 +0800)]
regulator: core: Call set_voltage_time_sel() only when the regulator is on
If the regulator is not on, it won't take time setting new voltage.
So only call set_voltage_time_sel() to get the necessary delay when
the regulator is on.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sun, 20 May 2012 02:30:21 +0000 (10:30 +0800)]
regulator: core: Allow drivers to set voltage mapping table in regulator_desc
Some regulator hardware use table based mapping can set volt_table in
regulator_desc and use regulator_list_voltage_table() for their list_voltage
callback.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linus Torvalds [Sun, 3 Jun 2012 00:39:40 +0000 (17:39 -0700)]
Merge tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper updates from Alasdair G Kergon:
"Improve multipath's retrying mechanism in some defined circumstances
and provide a simple reserve/release mechanism for userspace tools to
access thin provisioning metadata while the pool is in use."
* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm thin: provide userspace access to pool metadata
dm thin: use slab mempools
dm mpath: allow ioctls to trigger pg init
dm mpath: delay retry of bypassed pg
dm mpath: reduce size of struct multipath
Joe Thornber [Sat, 2 Jun 2012 23:30:01 +0000 (00:30 +0100)]
dm thin: provide userspace access to pool metadata
This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_. This,
read-only snapshot can be accessed by userland, concurrently with the
live target.
Only one metadata snapshot can be held at a time. The pool's status
line will give the block location for the current msnap.
Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:
thin_dump -m <msnap root> <metadata dev>
Available here: https://github.com/jthornber/thin-provisioning-tools
Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:
i) Incremental backups.
By using metadata snapshots we can work out what blocks have
changed over time. Combined with data snapshots we can ensure
the data doesn't change while we back it up.
A short proof of concept script can be found here:
Mike Snitzer [Sat, 2 Jun 2012 23:30:00 +0000 (00:30 +0100)]
dm thin: use slab mempools
Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mikulas Patocka [Sat, 2 Jun 2012 23:29:58 +0000 (00:29 +0100)]
dm mpath: allow ioctls to trigger pg init
After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device. Until this has happened, ioctls return -EAGAIN.
With this patch, new paths are made available in response to an ioctl
too. The processing of the ioctl gets delayed until this has happened.
Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.
Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure. Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands). For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too. It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mike Christie [Sat, 2 Jun 2012 23:29:45 +0000 (00:29 +0100)]
dm mpath: delay retry of bypassed pg
If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.
If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Acked-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mike Snitzer [Sat, 2 Jun 2012 23:29:43 +0000 (00:29 +0100)]
dm mpath: reduce size of struct multipath
Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes. Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes). This allows future flags to be added
without each consuming an unsigned int.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
1) Make syn floods consume significantly less resources by
a) Not pre-COW'ing routing metrics for SYN/ACKs
b) Mirroring the device queue mapping of the SYN for the SYN/ACK
reply.
Both from Eric Dumazet.
2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA.
3) Validate the length requested when building a paged SKB for a
socket, so we don't overrun the page vector accidently. From Jason
Wang.
4) When netlabel is disabled, we abort all IP option processing when we
see a CIPSO option. This isn't the right thing to do, we should
simply skip over it and continue processing the remaining options
(if any). Fix from Paul Moore.
5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel
Apfelbaum.
6) 8139cp enables the receiver before the ring address is properly
programmed, which potentially lets the device crap over random
memory. Fix from Jason Wang.
7) e1000/e1000e fixes for i217 RST handling, and an improper buffer
address reference in jumbo RX frame processing from Bruce Allan and
Sebastian Andrzej Siewior, respectively.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
fec_mpc52xx: fix timestamp filtering
mcs7830: Implement link state detection
e1000e: fix Rapid Start Technology support for i217
e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
r8169: call netif_napi_del at errpaths and at driver unload
tcp: reflect SYN queue_mapping into SYNACK packets
tcp: do not create inetpeer on SYNACK message
8139cp/8139too: terminate the eeprom access with the right opmode
8139cp: set ring address before enabling receiver
cipso: handle CIPSO options correctly when NetLabel is disabled
net: sock: validate data_len before allocating skb in sock_alloc_send_pskb()
bql: Avoid possible inconsistent calculation.
bql: Avoid unneeded limit decrement.
bql: Fix POSDIFF() to integer overflow aware.
net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP
net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap
net/mlx4_core: Fixes for VF / Guest startup flow
net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event
net/mlx4_core: Fix number of EQs used in ICM initialisation
net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int
Linus Torvalds [Sat, 2 Jun 2012 23:17:03 +0000 (16:17 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull straggler x86 fixes from Peter Anvin:
"Three groups of patches:
- EFI boot stub documentation and the ability to print error messages;
- Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which
should never have been ported, and the port is broken and
potentially dangerous.)
- ftrace stack corruption fixes. I'm not super-happy about the
technical implementation, but it is probably the least invasive in
the short term. In the future I would like a single method for
nesting the debug stack, however."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32
x86, efi: Add EFI boot stub documentation
x86, efi; Add EFI boot stub console support
x86, efi: Only close open files in error path
ftrace/x86: Do not change stacks in DEBUG when calling lockdep
x86: Allow nesting of the debug stack IDT setting
x86: Reset the debug_stack update counter
ftrace: Use breakpoint method to update ftrace caller
ftrace: Synchronize variable setting with breakpoints
Linus Torvalds [Sat, 2 Jun 2012 22:21:43 +0000 (15:21 -0700)]
tty: Revert the tty locking series, it needs more work
This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.
The main revert is d29f3ef39be4 ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:
fde86d310886 - tty: add lockdep annotations 8f6576ad476b - tty: fix ldisc lock inversion trace d3ca8b64b97e - pty: Fix lock inversion b1d679afd766 - tty: drop the pty lock during hangup abcefe5fc357 - tty/amiserial: Add missing argument for tty_unlock() fd11b42e3598 - cris: fix missing tty arg in wait_event_interruptible_tty call d29f3ef39be4 - tty_lock: Localise the lock
The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.
Stephan Gatzka [Sat, 2 Jun 2012 03:04:06 +0000 (03:04 +0000)]
fec_mpc52xx: fix timestamp filtering
skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org> Cc: stable <stable@vger.kernel.org> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary [Fri, 1 Jun 2012 10:29:08 +0000 (10:29 +0000)]
mcs7830: Implement link state detection
Add .status callback that detects link state changes.
Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver).
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 2 Jun 2012 16:03:54 +0000 (09:03 -0700)]
Merge 'for-linus' branches from git://git.kernel.org/pub/scm/linux/kernel/git/viro/{vfs,signal}
Pull vfs fix and a fix from the signal changes for frv from Al Viro.
The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc
actually depended on the default "unsigned long", while 32-bit powerpc
had an explicit override to "unsigned short". Al didn't notice, and
made both of them be the unsigned short.
The frv signal fix is fallout from simplifying the do_notify_resume()
code, and leaving an extra parenthesis.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
powerpc: Fix size of st_nlink on 64bit
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
frv: Remove bogus closing parenthesis
Anton Blanchard [Sat, 2 Jun 2012 11:34:52 +0000 (21:34 +1000)]
powerpc: Fix size of st_nlink on 64bit
commit e57f93cc53b7 (powerpc: get rid of nlink_t uses, switch to
explicitly-sized type) changed the size of st_nlink on ppc64 from
a long to a short, resulting in boot failures.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Bruce Allan [Thu, 10 May 2012 02:51:17 +0000 (02:51 +0000)]
e1000e: fix Rapid Start Technology support for i217
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead
of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY
register greater than the maximum allowed by the latter macro, and fix a
typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan.
Also for clarity, rename a few defines as bit definitions instead of masks.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
This is another fixup where the data is not transfered into buffer
addressed by skb->data but into a page.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linus Torvalds [Sat, 2 Jun 2012 02:56:23 +0000 (19:56 -0700)]
Merge branch 'akpm' (Fixups for Andrew's patchbomb)
Merge fixups for the mac NLS tables from Andrew.
* emailed from Andrew Morton, and one cleanup by me:
nls: fix (and rename) mac NLS table files and config options
fs/nls/Makefile: remove bogus CONFIG_ assignments
Linus Torvalds [Sat, 2 Jun 2012 02:51:22 +0000 (19:51 -0700)]
nls: fix (and rename) mac NLS table files and config options
The config options in the Kconfig file (with _CODEPAGE_ in the name)
didn't match the config option name in the Makefile (no _CODEPAGE_).
And both of them were of the hard-to-read MACXYZZY variety, which made
them hard to parse for normal humans: MACROMAN easily reads as "macro
man", not as "Mac Roman".
So rename the options to be consistent, and be NLS_MAC_xyzzy. Rename
the files to be mac-xyzzy.c too, and drop the "nls" part entirely (it's
already in the directory name).
Linus Torvalds [Fri, 1 Jun 2012 23:57:51 +0000 (16:57 -0700)]
Merge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
Linus Torvalds [Fri, 1 Jun 2012 23:55:42 +0000 (16:55 -0700)]
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
Linus Torvalds [Fri, 1 Jun 2012 23:51:37 +0000 (16:51 -0700)]
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform driver updates from Matthew Garrett:
"Some significant improvements for the Sony driver on newer machines,
but other than that mostly just minor fixes and a patch to remove the
broken rfkill code from the Dell driver."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (35 commits)
apple-gmux: Fix up the suspend/resume patch
dell-laptop: Remove rfkill code
toshiba_acpi: Fix mis-merge
dell-laptop: Add touchpad led support for Dell V3450
acer-wmi: add 3 laptops to video backlight vendor mode quirk table
sony-laptop: add touchpad enable/disable function
sony-laptop: add missing Fn key combos for 0x100 handlers
sony-laptop: add support for more WWAN modems
sony-laptop: new keyboard backlight handle
sony-laptop: add high speed battery charging function
sony-laptop: support automatic resume on lid open
sony-laptop: adjust error handling in finding SNC handles
sony-laptop: add thermal profiles support
sony-laptop: support battery care functions
sony-laptop: additional debug statements
sony-laptop: improve SNC initialization and acpi notify callback code
sony-laptop: use kstrtoul to parse sysfs values
sony-laptop: generalise ACPI calls into SNC functions
sony-laptop: fix return path when no ACPI buffer is allocated
sony-laptop: use soft rfkill status stored in hw
...
Linus Torvalds [Fri, 1 Jun 2012 23:50:23 +0000 (16:50 -0700)]
Merge branch 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
Pull slab updates from Pekka Enberg:
"Mainly a bunch of SLUB fixes from Joonsoo Kim"
* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
slub: use __SetPageSlab function to set PG_slab flag
slub: fix a memory leak in get_partial_node()
slub: remove unused argument of init_kmem_cache_node()
slub: fix a possible memory leak
Documentations: Fix slabinfo.c directory in vm/slub.txt
slub: fix incorrect return type of get_any_partial()
Linus Torvalds [Fri, 1 Jun 2012 22:46:46 +0000 (15:46 -0700)]
Merge branch 'ux500/hickup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm fixes for ux500 mismerge mishap from Arnd Bergmann:
"The device tree conversion for arm/ux500 in 3.5 turns out to be
incomplete because of a mismerge done by Linus Walleij that I failed
to notice early enough and that Lee Jones as the original author of
those patches did not manage to fix during the -next cycle. While we
originally to get a much larger set of ux500 device tree enablement
patches merged, this did not happen in time.
After some discussion at Linaro Connect conference this week, Lee has
been able to do damage control and provide a series to put the broken
platform back into usable shape for both DT and non-DT based booting.
This series has not been part of linux-next and is based on top of the
current state of the upstream kernel rather than an -rc, but this is
the best we could manage given the earlier breakage."
* 'ux500/hickup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: Enable probing of pinctrl through Device Tree
ARM: ux500: Add support for ab8500 regulators into the Device Tree
ARM: ux500: Provide regulator support for SMSC911x via Device Tree
ARM: ux500: Allow PRCMU regulator to be probed during a DT enabled boot
ARM: ux500: Apply db8500-prcmu regulator information to db8500 Device Tree
ARM: ux500: Only initialise STE's UIBs on boards which support them
ARM: ux500: Disable platform setup of the ab8500 when DT is enabled
ARM: ux500: Use correct format for dynamic IRQ assignment
ARM: ux500: Re-enable SMSC911x platform code registration during non-DT boots
ARM: ux500: PRCMU related configuration and layout corrections for Device Tree
ARM: ux500: Remove DB8500 PRCMU platform registration when DT is enabled
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: New DT:ed u8500_init_devices for one-by-one device enablement
ARM: ux500: New DT:ed snowball_platform_devs for one-by-one device enablement
pinctrl-nomadik: Allow Device Tree driver probing
Devendra Naga [Thu, 31 May 2012 01:51:20 +0000 (01:51 +0000)]
r8169: call netif_napi_del at errpaths and at driver unload
when register_netdev fails, the init'ed NAPIs by netif_napi_add must be
deleted with netif_napi_del, and also when driver unloads, it should
delete the NAPI before unregistering netdevice using unregister_netdev.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 1 Jun 2012 22:40:29 +0000 (15:40 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of fixes:
- vmware memory corruption
- ttm spinlock balance
- cirrus/mgag200 work in the presence of efifb
and finally Alex and Jerome managed to track down a magic set of bits
that on certain rv740 and evergreen cards allow the correct use of the
complete set of render backends, this makes the cards operate
correctly in a number of scenarios we had issues in before, it also
manages to boost speed on benchmarks my large amounts on these
specific gpus."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/edid: Make the header fixup threshold tunable
drm/radeon: fix regression in UMS CS ioctl
drm/vmwgfx: Fix nasty write past alloced memory area
drm/ttm: Fix spinlock imbalance
drm/radeon: fixup tiling group size and backendmap on r6xx-r9xx (v4)
drm/radeon: fix HD6790, HD6570 backend programming
drm/radeon: properly program gart on rv740, juniper, cypress, barts, hemlock
drm/radeon: fix bank information in tiling config
drm/mgag200: kick off conflicting framebuffers earlier.
drm/cirrus: kick out conflicting framebuffers earlier
cirrus: avoid crash if driver fails to load
Linus Torvalds [Fri, 1 Jun 2012 22:39:26 +0000 (15:39 -0700)]
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few trivial driver-specific fixes."
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hdspm - Work around broken DDS value on PCI RME MADI
ALSA: usb-audio: fix rate_list memory leak
ASoC: fsi: bugfix: ensure dma is terminated
ASoC: fsi: bugfix: correct dma area
ASoC: fsi: bugfix: enable master clock control on DMA stream
ASoC: imx-ssi: Use clk_prepare_enable/clk_disable_unprepare
projects / linux-beck.git / log