The ad7180 has multiple register pages which can be switched between by
writing to a register. Currently the driver manually switches between pages
whenever a register outside of the default register map is accessed and
switches back after it has been accessed. This is a bit tedious and also
potential source for bugs.
This patch adds two helper functions that take care of switching between
pages and reading/writing the register. The register numbers for registers
are updated to encode both the page (in the upper 8-bits) and the register
(in the lower 8-bits) numbers.
Having multiple pages means that a register access is not a single atomic
i2c_smbus_write_byte_data() or i2c_smbus_read_byte_data() call and we need
to make sure that concurrent register access does not race against each
other.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Federico Vaga <federico.vaga@gmail.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Consistently prefix register defines with ADV7180_REG. Also remove the "ADI"
from register names, the ADV7180 prefix should provide enough of a namespace
separation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Federico Vaga <federico.vaga@gmail.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] adv7180: Pass correct flags to request_threaded_irq()
Most IRQ controllers support different types of interrupts. The adv7180
generates falling edge interrupts, so make sure to pass IRQF_TRIGGER_FALLING
to request_threaded_irq() so the IRQ controller is configured for the
correct mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Federico Vaga <federico.vaga@gmail.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] adv7180: Do not request the IRQ again during resume
Currently the IRQ is requested from within the init_device() function. This
function is not only called during device probe, but also during resume
causing the driver to try to request the IRQ again. Move requesting the IRQ
from init_device() to the probe function to make sure that it is only
requested once.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Federico Vaga <federico.vaga@gmail.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Arnd Bergmann [Thu, 29 Jan 2015 16:12:05 +0000 (13:12 -0300)]
[media] davinci: add V4L2 dependencies
The davinci media drivers use videobuf2, which they enable through
a 'select' statement. If one of these drivers is built-in, but
the v4l2 core is a loadable modules, we end up with a link
error:
drivers/built-in.o: In function `vb2_fop_mmap':
:(.text+0x113e84): undefined reference to `video_devdata'
drivers/built-in.o: In function `vb2_ioctl_create_bufs':
:(.text+0x114710): undefined reference to `video_devdata'
drivers/built-in.o: In function `vb2_ioctl_reqbufs':
:(.text+0x114ed8): undefined reference to `video_devdata'
drivers/built-in.o: In function `vb2_ioctl_querybuf':
:(.text+0x115530): undefined reference to `video_devdata'
To solve this, we need to add a dependency on VIDEO_V4L2,
which enforces that the davinci drivers themselves can only
be loadable modules if V4L2 is not built-in, and they do
not cause the videobuf2 code to be built-in.
Arnd Bergmann [Wed, 28 Jan 2015 21:17:44 +0000 (18:17 -0300)]
[media] siano: fix Kconfig dependencies
The USB and MMC front-ends to the siano driver both only make
sense when combined with the SMS_SIANO_MDTV driver. That driver
already requires RC_CORE to not be a module, so we also need
to add that dependency here.
drivers/built-in.o: In function `smssdio_remove':
:(.text+0x155bd8): undefined reference to `smscore_putbuffer'
:(.text+0x155bdc): undefined reference to `smscore_unregister_device'
drivers/built-in.o: In function `smssdio_interrupt':
:(.text+0x155e4c): undefined reference to `smsendian_handle_rx_message'
:(.text+0x155e50): undefined reference to `smscore_onresponse'
:(.text+0x155e54): undefined reference to `smscore_getbuffer'
:(.text+0x155e58): undefined reference to `smscore_putbuffer'
drivers/built-in.o: In function `smssdio_sendrequest':
:(.text+0x155f20): undefined reference to `smsendian_handle_tx_message'
drivers/built-in.o: In function `smssdio_probe':
:(.text+0x15610c): undefined reference to `sms_get_board'
:(.text+0x156114): undefined reference to `smscore_register_device'
:(.text+0x156118): undefined reference to `smscore_set_board_id'
:(.text+0x156128): undefined reference to `smscore_unregister_device'
:(.text+0x156140): undefined reference to `smscore_start_device'
Arnd Bergmann [Wed, 28 Jan 2015 21:17:41 +0000 (18:17 -0300)]
[media] timberdale: do not select TIMB_DMA
The timberdale media driver requires the use of the respective
dma engine driver, but that may not be enabled, causing a
Kconfig warning:
warning: (VIDEO_TIMBERDALE) selects TIMB_DMA which has unmet direct dependencies (DMADEVICES && MFD_TIMBERDALE)
This fixes the dependency by removing the inappropriate 'select'
statement and replacing it with a direct dependency on the
drivers that provide the services this needs.
Fixes: 7155043c2d027 ("[media] enable COMPILE_TEST for media drivers") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prabhakar Lad [Mon, 26 Jan 2015 14:50:15 +0000 (11:50 -0300)]
[media] media: am437x: fix sparse warnings
This patch fixes following spare warnings:
drivers/media/platform/am437x/am437x-vpfe.c:66:28: warning: symbol 'vpfe_standards' was not declared. Should it be static?
drivers/media/platform/am437x/am437x-vpfe.c:2202:57: warning: incorrect type in argument 2 (different address spaces)
drivers/media/platform/am437x/am437x-vpfe.c:2202:57: expected void [noderef] <asn:1>*params
drivers/media/platform/am437x/am437x-vpfe.c:2202:57: got void *param
include/linux/spinlock.h:364:9: warning: context imbalance in 'vpfe_start_streaming' - unexpected unlock
[media] pvrusb2: use msecs_to_jiffies for conversion
This is only an API consolidation and should make things more readable
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] cx231xx: fix usbdev leak on failure paths in cx231xx_usb_probe()
Commit b7085c086475 ("cx231xx: convert from pr_foo to dev_foo")
moves usb_get_dev(interface_to_usbdev(interface)) to the beginning
of cx231xx_usb_probe() to use udev->dev in dev_err(),
but it does not make sure usbdev is put on all failure paths.
Later dev_err(udev->dev) was replaced by dev_err(d).
So the patch moves usb_get_dev() below (before the first use)
and fixes another failure path.
Found by Linux Driver Verification project (linuxtesting.org).
William Towle [Mon, 26 Jan 2015 17:08:40 +0000 (14:08 -0300)]
[media] rcar_vin: move buffer management to .stop_streaming handler
This commit moves the "buffer in use" logic from the .buf_cleanup
handler into .stop_streaming, based on advice that this is its
proper logical home.
By ensuring the list of pointers in priv->queue_buf[] is managed
as soon as possible, we avoid warnings concerning buffers in ACTIVE
state when the system cleans up after streaming stops. This fixes a
problem with modification of buffers after their content has been
cleared for passing to userspace.
After the refactoring, the buf_init and buf_cleanup functions were
found to contain only initialisation/release steps as are carried out
elsewhere if omitted; these functions and references were removed.
Ian Molton [Mon, 26 Jan 2015 17:08:39 +0000 (14:08 -0300)]
[media] rcar_vin: helper function for streaming stop
The code that tests that capture from a stream has stopped is
presently insufficient and the potential for a race condition
exists where frame capture may generate an interrupt between
requesting the capture process halt and freeing buffers.
This patch refactors code out of rcar_vin_videobuf_release() and
into rcar_vin_wait_stop_streaming(), and ensures there are calls
in places where we need to know that capturing has finished.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk> Signed-off-by: William Towle <william.towle@codethink.co.uk> Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Lad, Prabhakar [Wed, 26 Nov 2014 22:42:27 +0000 (19:42 -0300)]
[media] soc_camera: use vb2_ops_wait_prepare/finish helper
This patch drops driver specific wait_prepare() and
wait_finish() callbacks from vb2_ops and instead uses
the the helpers vb2_ops_wait_prepare/finish() provided
by the vb2 core, the lock member of the queue needs
to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Philipp Zabel [Fri, 23 Jan 2015 16:51:34 +0000 (13:51 -0300)]
[media] coda: allocate bitstream ringbuffer only for BIT decoder
The BIT encoder does not use a per-context bitstream ringbuffer as it encodes
directly into the videobuf2 capture queue's buffers. Avoid allocation of the
bitstream ringbuffer for encoder contexts.
Philipp Zabel [Fri, 23 Jan 2015 16:51:30 +0000 (13:51 -0300)]
[media] coda: switch BIT decoder source queue to vmalloc
Since we have to copy from input buffers into the bitstream ringbuffer
with the CPU, there is no need for contiguous DMA buffers on the decoder
input side.
Philipp Zabel [Fri, 23 Jan 2015 16:51:28 +0000 (13:51 -0300)]
[media] coda: don't ever use subsampling ping-pong buffers as reconstructed reference buffers
On i.MX6, two subsampling ping-pong buffers are used for motion estimation and
deblocking They should not be counted as framebuffers, or they will be also used
to store reconstructed frames, causing visible artifacts in P-frames.
Philipp Zabel [Fri, 23 Jan 2015 16:51:27 +0000 (13:51 -0300)]
[media] coda: issue seq_end_work during stop_streaming
This patch queues seq_end_work and flushes the queue during stop_streaming
and clears the ctx->initialized flag. This allows to start streaming again
after stopping streaming without releasing the context.
Philipp Zabel [Fri, 23 Jan 2015 16:51:26 +0000 (13:51 -0300)]
[media] coda: remove unused isequence, reset qsequence in stop_streaming
The isequence counter is never used, qsequence counts the buffers queued into
the bit decoder bitstream ringbuffer. It needs to be reset in stop_streaming.
Philipp Zabel [Fri, 23 Jan 2015 16:51:20 +0000 (13:51 -0300)]
[media] coda: fix job_ready debug reporting for bitstream decoding
Clarify whether job_ready returns false because the context is on hold, waiting
for new input buffers, whether there are not enough input buffers to fill two
into the bitstream, or whether there is not enough data in the bitstream buffer
for the bitstream reader hardware to read a whole frame.
Lucas Stach [Fri, 23 Jan 2015 16:51:19 +0000 (13:51 -0300)]
[media] coda: adjust sequence offset after unexpected decoded frame
If userspace doesn't properly separate the bitstream input into
individual frames (which may happen for example on slightly
corrupted streams) the CODA hardware may decode more frames
than we expect. We already log an error in this case, but it's
also necessary to adjust the sequence offset. Otherwise we
spam the log with a sequence number mismatch on every frame
frame after the unexpected one.
Philipp Zabel [Fri, 23 Jan 2015 16:51:18 +0000 (13:51 -0300)]
[media] coda: move meta out of padding
Handle an empty buffer metadata list without crashing. This can happen
if the decoder is fed a broken stream, or multiple compressed frames in
a single queued buffer.
Nicolas Dufresne [Mon, 15 Dec 2014 21:10:59 +0000 (18:10 -0300)]
[media] media-doc: Fix MFC display delay control doc
The V4L2_CID_MPEG_MFC51_VIDEO_DECODER_H264_DISPLAY_DELAY_ENABLE control
is a boolean but was documented as a integer. The documentation was
also slightly miss-leading.
Nicolas Dufresne [Mon, 15 Dec 2014 21:10:57 +0000 (18:10 -0300)]
[media] s5p-mfc-v6+: Use display_delay_enable CID
The MFC driver has two controls, DISPLAY_DELAY and DISPLAY_DELAY_ENABLE
that allow forcing the decoder to return a decoded frame sooner
regardless of the order. The added support for firmware version 6 and
higher was not taking into account the DISPLAY_DELAY_ENABLE boolean.
Instead it had a comment stating that DISPLAY_DELAY should be set to a
negative value to disable it. This is not possible since the control
range is from 0 to 65535. This feature was also supposed to be disabled
by default in order to produce frames in display order.
These drivers haven't been tested in a long, long time. The hardware is
ancient and hopelessly obsolete. These drivers also need to be converted
to newer media frameworks but due to the lack of hardware that's going
to be impossible. In addition, cheaper and vastly better hardware is
available today.
These drivers are already deprecated, so now remove them altogether.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Tue, 23 Dec 2014 12:14:37 +0000 (09:14 -0300)]
[media] vino/saa7191: remove deprecated drivers
These drivers haven't been tested in a long, long time. The hardware is
ancient and hopelessly obsolete. These drivers also need to be converted
to newer media frameworks but due to the lack of hardware that's going
to be impossible.
So these drivers are a prime candidate for removal. If someone is
interested in working on these drivers to prevent their removal, then
please contact the linux-media mailinglist.
These drivers are already deprecated, so now remove them altogether.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Tue, 23 Dec 2014 12:11:48 +0000 (09:11 -0300)]
[media] tlg2300: remove deprecated staging driver
This driver hasn't been tested in a long, long time. The company that made
this chip has gone bust many years ago and hardware using this chip is next
to impossible to find.
This driver needs to be converted to newer media frameworks but due to the
lack of hardware that's going to be impossible. Since cheap alternatives are
easily available, there is little point in keeping this driver alive.
This driver is already deprecated, so now remove it altogether.
Rename firmare download error path goto label. Remove firmware NULL
set as NULL value is not needed anymore, due to recent change which
started using goto labels for firmware error handling.
Cc: Olli Salonen <olli.salonen@iki.fi> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Antti Palosaari [Sat, 6 Dec 2014 17:40:06 +0000 (14:40 -0300)]
[media] si2157: carry pointer to client instead of state in tuner_priv
Carry struct i2c_client pointer in tuner_priv. This driver is I2C driver,
which is represented as a struct i2c_client, so better to carry this top
level structure for each routine in order to unify things.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Antti Palosaari [Sat, 6 Dec 2014 20:43:27 +0000 (17:43 -0300)]
[media] si2168: print chip version
Print chip version once using log level into when init() is called.
Remove cold/warm state printing as those are not very useful.
old printing:
si2168 6-0064: found a 'Silicon Labs Si2168' in cold state
si2168 6-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 6-0064: firmware version: 4.0.11
si2168 6-0064: found a 'Silicon Labs Si2168' in warm state
new printing:
si2168 6-0064: found a 'Silicon Labs Si2168-B40'
si2168 6-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 6-0064: firmware version: 4.0.11
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Antti Palosaari [Fri, 5 Dec 2014 20:08:22 +0000 (17:08 -0300)]
[media] si2168: enhance firmware download routine
All known old firmware firmware formats are downloaded using 8 byte
chunks. Reject firmware if it could not be divided to 8 byte chunks
and because of that we could simplify some calculations. Now both
supported firmware download routines are rather similar.
Cc: Olli Salonen <olli.salonen@iki.fi> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Antti Palosaari [Fri, 5 Dec 2014 19:02:42 +0000 (16:02 -0300)]
[media] si2168: add own goto label for kzalloc failure
Use own label for kzalloc failure in which does not call kfree().
kfree() could be called with NULL, but it is still better to have
own label which skips unnecessary kfree().
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Antti Palosaari [Fri, 5 Dec 2014 18:04:12 +0000 (15:04 -0300)]
[media] si2168: change firmware version print from debug to info
Even firmware version is not needed to know, it is still interesting
and useful to know some cases. Due to that increase its printing to
info log level.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Antti Palosaari [Tue, 25 Nov 2014 20:31:43 +0000 (17:31 -0300)]
[media] si2168: carry pointer to client instead of state
Carry struct i2c_client pointer inside struct dvb_frontend private
pointer. This driver is I2C driver, which is represented as a
struct i2c_client, so better to carry this top level structure for
each routine in order to unify things. This allows further
simplification.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[media] lgdt3305: add support for fixed tp clock mode
Add support for controlling TP clock mode for VSB and QAM annex-B/C mode.
Gated clock mode is the default value, and does not support QAM annex-C.
The patch enables setting this control to fixed clock mode.
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Luca Bonissi [Mon, 26 Jan 2015 10:38:17 +0000 (07:38 -0300)]
[media] gspca_vc032x: Fix wrong bytesperline
I found a problem on vc032x gspca usb webcam subdriver: "bytesperline"
property is wrong for YUYV and YVYU formats.
With recent v4l-utils library (>=0.9.1), that uses "bytesperline" for
pixel format conversion, the result is a wrong jerky image.
Patch tested on my laptop (USB webcam Logitech Orbicam 046d:0892).
Hans de Goede [Thu, 15 Jan 2015 10:42:36 +0000 (07:42 -0300)]
[media] gspca: Fix underflow in vidioc_s_parm()
"n" is a user controlled integer. The code here doesn't handle the case
where "n" is negative and this causes a static checker warning.
drivers/media/usb/gspca/gspca.c:1571 vidioc_s_parm()
warn: no lower bound on 'n'
parm.capture.readbuffers is unsigned, so make n unsigned too, fixing this.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Joe Howse [Mon, 29 Dec 2014 15:00:03 +0000 (12:00 -0300)]
[media] gspca: Add high-speed modes for PS3 Eye camera
Add support in the PS3 Eye driver for QVGA capture at higher
frame rates: 187, 150, and 137 FPS. This functionality is valuable
because the PS3 Eye is popular for computer vision projects and no
other camera in its price range supports such high frame rates.
Correct a QVGA mode that was listed as 40 FPS. It is really 37 FPS
(half of 75 FPS).
Tests confirm that the nominal frame rates are achieved.
Signed-off-by: Joe Howse <josephhowse@nummist.com> Tested-by: Antonio Ospite <ao2@ao2.it> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Antonio Ospite [Fri, 11 Jul 2014 12:56:57 +0000 (09:56 -0300)]
[media] gspca_stv06xx: enable button found on some Quickcam Express variant
Signed-off-by: Antonio Ospite <ao2@ao2.it> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Mon, 4 Aug 2014 10:29:59 +0000 (07:29 -0300)]
[media] pwc: fix WARN_ON
If start_streaming fails, then the buffers must be given back to vb2 with state
QUEUED, not ERROR. Otherwise a WARN_ON will be generated.
In the disconnect it is pointless to call pwc_cleanup_queued_bufs() as stop_streaming()
will be called anyway.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans de Goede [Thu, 20 Nov 2014 15:10:47 +0000 (12:10 -0300)]
[media] rc: sunxi-cir: Add support for the larger fifo found on sun5i and sun6i
Add support for the larger fifo found on sun5i and sun6i, having a separate
compatible for the ir found on sun5i & sun6i also is useful if we ever want
to add ir transmit support, because the sun5i & sun6i version do not have
transmit support.
Note this commits also adds checking for the end-of-packet interrupt flag
(which was already enabled), as the fifo-data-available interrupt flag only
gets set when the trigger-level is exceeded. So far we've been getting away
with not doing this because of the low trigger-level, but this is something
which we should have done since day one.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
John McMaster [Mon, 1 Dec 2014 02:27:53 +0000 (23:27 -0300)]
[media] gspca_touptek: Add support for ToupTek UCMOS series USB cameras
Adds support for AmScope MU800 / ToupTek UCMOS08000KPB USB microscope camera.
Signed-off-by: John McMaster <johndmcmaster@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil [Tue, 27 Jan 2015 16:46:17 +0000 (13:46 -0300)]
[media] vivid: Y offset should depend on quant. range
When converting to or from Y'CbCr and R'G'B' the Y offset depends
on the quantization range: it's 0 for full and 16 for limited range.
But in the code it was hardcoded to 16. This messed up the brightness
of the generated pattern.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Antti Palosaari [Tue, 2 Dec 2014 14:23:49 +0000 (11:23 -0300)]
[media] rtl28xxu: change module unregister order
We must unregister frontend first and after that driver itself. That
order went wrong after demod drivers were switched to kernel I2C
drivers, causing crashes.
Tested-by: Benjamin Larsson <benjamin@southpole.se> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video_device debug field has been renamed to dev_debug, resulting in
a compilation failure. As v4l2 debugging is supposed to be controlled
through a sysfs attribute created by the v4l2 core, there's no need to
duplicate debug control through a module parameter. Remove it.
The UVC spec is a bit vague wrt devices using bulk endpoints,
specifically, how to signal to a device to start streaming.
For devices using isoc endpoints, the sequence for start streaming is:
1) The host sends PROBE_CONTROL(SET_CUR) PROBE_CONTROL(GET_CUR)
2) Host selects desired config and calls COMMIT_CONTROL(SET_CUR)
3) Host selects an alt interface other then zero - e.g SELECT_ALTERNATE_INTERFACE(1)
4) The device starts streaming
However for devices using bulk endpoints, there must be *no* alt interface
other than setting zero. From the UVC spec:
"A VideoStreaming interface containing a bulk endpoint for streaming shall
support only alternate setting zero. Additional alternate settings containing
bulk endpoints are not permitted in a device that is compliant with the Video
Class specification."
So for devices using bulk endpoints, step #3 above is irrelevant, and thus
cannot be used as an indication for the device to start streaming.
So in practice, such devices start streaming immediately after a
COMMIT_CONTROL(SET_CUR).
In the uvc resume() handler, an unsolicited commit is sent, which causes
devices using bulk endpoints to start streaming unintentionally.
This patch modifies resume() handler to send a commit only if streaming
needs to be reestablished, i.e if the device was actually streaming before is
was suspended.
Hans Verkuil [Fri, 19 Dec 2014 12:14:22 +0000 (09:14 -0300)]
[media] hdmi: rename HDMI_AUDIO_CODING_TYPE_EXT_STREAM to _EXT_CT
As per the suggestion of Thierry Reding rename
HDMI_AUDIO_CODING_TYPE_EXT_STREAM to HDMI_AUDIO_CODING_TYPE_EXT_CT to
be consistent with the CEA-861 spec.
Martin Bugge [Fri, 19 Dec 2014 12:14:21 +0000 (09:14 -0300)]
[media] hdmi: added unpack and logging functions for InfoFrames
When receiving video it is very useful to be able to unpack the InfoFrames.
Logging is useful as well, both for transmitters and receivers.
Especially when implementing the VIDIOC_LOG_STATUS ioctl (supported by many
V4L2 drivers) for a receiver it is important to be able to easily log what
the InfoFrame contains. This greatly simplifies debugging.
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Dan Carpenter [Thu, 8 Jan 2015 10:07:08 +0000 (07:07 -0300)]
[media] coda: improve safety in coda_register_device()
The "i" variable is used as an offset into both the dev->vfd[] and the
dev->devtype->vdevs[] arrays. The second array is smaller so we should
use that as a limit instead of ARRAY_SIZE(dev->vfd). Also the original
check was off by one.
We should use a format string as well in case the ->name has any funny
characters and also to stop static checkers from complaining.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
projects / karo-tx-linux.git / log