Bart Van Assche [Wed, 12 Jun 2013 13:24:25 +0000 (15:24 +0200)]
IB/srp: Skip host settle delay
The SRP initiator implements host reset by reconnecting to the SRP
target. That means that communication with the target is possible as
soon as host reset finished. Hence skip the host settle delay.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Sebastian Riemer <sebastian.riemer@profitbricks.com> Reviewed-by: Christoph Hellwig <hch@infradead.org> Acked-by: David Dillow <dillowda@ornl.gov> Signed-off-by: Roland Dreier <roland@purestorage.com>
Bart Van Assche [Wed, 12 Jun 2013 13:23:04 +0000 (15:23 +0200)]
IB/srp: Avoid skipping srp_reset_host() after a transport error
The SCSI error handler assumes that the transport layer is operational
if an eh_abort_handler() returns SUCCESS. Hence srp_abort() only
should return SUCCESS if sending the ABORT TASK task management
function succeeded. This patch avoids the SCSI error handler skipping
the srp_reset_host() call after a transport layer error.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Acked-by: David Dillow <dillowda@ornl.gov> Signed-off-by: Roland Dreier <roland@purestorage.com>
Dotan Barak [Wed, 12 Jun 2013 13:20:36 +0000 (15:20 +0200)]
IB/srp: Fix remove_one crash due to resource exhaustion
If the add_one callback fails during driver load no resources are
allocated so there isn't a need to release any resources. Trying
to clean the resource may lead to the following kernel panic:
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il> Reviewed-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Acked-by: Sebastian Riemer <sebastian.riemer@profitbricks.com> Acked-by: David Dillow <dillowda@ornl.gov> Signed-off-by: Roland Dreier <roland@purestorage.com>
Dave Airlie [Thu, 20 Jun 2013 01:48:52 +0000 (11:48 +1000)]
drm: add hotspot support for cursors.
So it looks like for virtual hw cursors on QXL we need to inform
the "hw" device what the cursor hotspot parameters are. This
makes sense if you think the host has to draw the cursor and interpret
clicks from it. However the current modesetting interface doesn't support
passing the hotspot information from userspace.
This implements a new cursor ioctl, that takes the hotspot info as well,
userspace can try calling the new interface and if it gets -ENOSYS it means
its on an older kernel and can just fallback.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/tilcdc: Clear bits of register we're going to set.
Bits weren't cleared so resolution changes didn't work.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Darren Etheridge <detheridge@ti.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Darren Etheridge [Fri, 21 Jun 2013 18:52:27 +0000 (13:52 -0500)]
drm/tilcdc fixing i2c/slave initialization race
In certain senarios drm will initialize before i2c this means that i2c
slave devices like the nxp tda998x will fail to be probed. This patch
detects this condition then defers the probe of the slave device and
the tilcdc main driver.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Darren Etheridge [Fri, 21 Jun 2013 18:52:25 +0000 (13:52 -0500)]
drm/tilcdc: adding more guards to prevent selection of invalid modes
The tilcdc has a number of limitations for the allowed sizes of
the various adjustable timing parameter. Some modes are outside
of these timings. This commit will prune modes that report timings
that will overflow the allowed sizes in the tilcdc.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Darren Etheridge [Fri, 21 Jun 2013 18:52:24 +0000 (13:52 -0500)]
drm/tilcdc: fixing off by one errors found on analyzer
When hooking up to an HDMI analyzer noticed some timings were
off by one. Referring to the hardware technical reference manual
for the lcd controller some of the timing registers use 0 to
represent 1. This patch addresses that issue.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Darren Etheridge [Fri, 21 Jun 2013 18:52:23 +0000 (13:52 -0500)]
drm/tilcdc: adding some more devicetree config
Adding support for max-pixelclock and max-width device tree
entries. As some devices that use the tilcdc hardware module
have restrictions on the allowed/tested values. Also update DT
bindings document to reflect new parameters.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Darren Etheridge [Fri, 21 Jun 2013 18:52:22 +0000 (13:52 -0500)]
drm/tilcdc: support pixel widths greater than 1024
TI LCD controller version 2 has an extended eleventh
bit that enables horizontal resolutions greater than
1024 pixels to be specified (upto 2048). This patch
adds support for setting this bit on LCDC V2.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Julia Lemire [Thu, 27 Jun 2013 17:38:59 +0000 (13:38 -0400)]
drm/mgag200: Added resolution and bandwidth limits for various G200e products.
At the larger resolutions, the g200e series sometimes struggles with
maintaining a proper output. Problems like flickering or black bands appearing
on screen can occur. In order to avoid this, limitations regarding resolutions
and bandwidth have been added for the different variations of the g200e series.
This code was ported from the old xorg mga driver.
Signed-off-by: Julia Lemire <jlemire@matrox.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
* freezer:
af_unix: use freezable blocking calls in read
sigtimedwait: use freezable blocking call
nanosleep: use freezable blocking call
futex: use freezable blocking call
select: use freezable blocking call
epoll: use freezable blocking call
binder: use freezable blocking calls
freezer: add new freezable helpers using freezer_do_not_count()
freezer: convert freezable helpers to static inline where possible
freezer: convert freezable helpers to freezer_do_not_count()
freezer: skip waking up tasks with PF_FREEZER_SKIP set
freezer: shorten freezer sleep time using exponential backoff
lockdep: check that no locks held at freeze time
lockdep: remove task argument from debug_check_no_locks_held
freezer: add unsafe versions of freezable helpers for CIFS
freezer: add unsafe versions of freezable helpers for NFS
projects / karo-tx-linux.git / log