Darren Etheridge [Fri, 21 Jun 2013 18:52:27 +0000 (13:52 -0500)]
drm/tilcdc fixing i2c/slave initialization race
In certain senarios drm will initialize before i2c this means that i2c
slave devices like the nxp tda998x will fail to be probed. This patch
detects this condition then defers the probe of the slave device and
the tilcdc main driver.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Darren Etheridge [Fri, 21 Jun 2013 18:52:25 +0000 (13:52 -0500)]
drm/tilcdc: adding more guards to prevent selection of invalid modes
The tilcdc has a number of limitations for the allowed sizes of
the various adjustable timing parameter. Some modes are outside
of these timings. This commit will prune modes that report timings
that will overflow the allowed sizes in the tilcdc.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Darren Etheridge [Fri, 21 Jun 2013 18:52:24 +0000 (13:52 -0500)]
drm/tilcdc: fixing off by one errors found on analyzer
When hooking up to an HDMI analyzer noticed some timings were
off by one. Referring to the hardware technical reference manual
for the lcd controller some of the timing registers use 0 to
represent 1. This patch addresses that issue.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Darren Etheridge [Fri, 21 Jun 2013 18:52:23 +0000 (13:52 -0500)]
drm/tilcdc: adding some more devicetree config
Adding support for max-pixelclock and max-width device tree
entries. As some devices that use the tilcdc hardware module
have restrictions on the allowed/tested values. Also update DT
bindings document to reflect new parameters.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Darren Etheridge [Fri, 21 Jun 2013 18:52:22 +0000 (13:52 -0500)]
drm/tilcdc: support pixel widths greater than 1024
TI LCD controller version 2 has an extended eleventh
bit that enables horizontal resolutions greater than
1024 pixels to be specified (upto 2048). This patch
adds support for setting this bit on LCDC V2.
Signed-off-by: Darren Etheridge <detheridge@ti.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Julia Lemire [Thu, 27 Jun 2013 17:38:59 +0000 (13:38 -0400)]
drm/mgag200: Added resolution and bandwidth limits for various G200e products.
At the larger resolutions, the g200e series sometimes struggles with
maintaining a proper output. Problems like flickering or black bands appearing
on screen can occur. In order to avoid this, limitations regarding resolutions
and bandwidth have been added for the different variations of the g200e series.
This code was ported from the old xorg mga driver.
Signed-off-by: Julia Lemire <jlemire@matrox.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Egbert Eich [Thu, 13 Jun 2013 19:01:19 +0000 (21:01 +0200)]
drm/edid: Don't print messages regarding stereo or csync by default
drm_mode_detailed() is called quite often, therefore when a monitor
that has a detailed timing mode marked DRM_EDID_PT_STEREO or requiring
composite sync, warning messages will clutter up the kernel log.
Like we already do for incorrect hsync/vsync pluse widths, print these
messages only when KMS debugging is enabled.
Signed-off-by: Egbert Eich <eich@suse.com> Reviewed-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
drm: drm_stub: Fixing return value if driver master_set call failed
When dev->driver->master_set() failed ioctl call return 0
but the caller is not the DRM-Master because file_priv->is_master = 0.
Fix that by returning to ioctl caller the driver master_set error code.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 27 Jun 2013 10:42:09 +0000 (20:42 +1000)]
Merge branch 'core/mutexes' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into drm-next
Merge in the tip core/mutexes branch for future GPU driver use.
Ingo will send this branch to Linus prior to drm-next.
* 'core/mutexes' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
locking-selftests: Handle unexpected failures more strictly
mutex: Add more w/w tests to test EDEADLK path handling
mutex: Add more tests to lib/locking-selftest.c
mutex: Add w/w tests to lib/locking-selftest.c
mutex: Add w/w mutex slowpath debugging
mutex: Add support for wound/wait style locks
arch: Make __mutex_fastpath_lock_retval return whether fastpath succeeded or not
powerpc/pci: Fix boot panic on mpc83xx (regression)
s390/ipl: Fix FCP WWPN and LUN format strings for read
fs: fix new splice.c kernel-doc warning
spi/pxa2xx: fix memory corruption due to wrong size used in devm_kzalloc()
s390/mem_detect: fix memory hole handling
s390/dma: support debug_dma_mapping_error
s390/dma: fix mapping_error detection
s390/irq: Only define synchronize_irq() on SMP
Input: xpad - fix for "Mad Catz Street Fighter IV FightPad" controllers
Input: wacom - add a new stylus (0x100802) for Intuos5 and Cintiqs
spi/pxa2xx: use GFP_ATOMIC in sg table allocation
fuse: hold i_mutex in fuse_file_fallocate()
Input: add missing dependencies on CONFIG_HAS_IOMEM
...
Daniel Vetter [Wed, 5 Jun 2013 22:17:25 +0000 (00:17 +0200)]
drm: kms_helper: don't lose hotplug event
There's a race window (small for hpd, 10s large for polled outputs)
where userspace could sneak in with an unrelated connnector probe
ioctl call and eat the hotplug event (since neither the hpd nor the
poll code see a state change).
To avoid this, check whether the connector state changes in all other
->detect calls (in the current helper code that's only probe_single)
and if that's the case, fire off a hotplug event. Note that we can't
directly call the hotplug event handler, since that expects that no
locks are held (due to reentrancy with the fb code to update the kms
console).
Also, this requires that drivers using the probe_single helper
function set up the poll work. All current drivers do that already,
and with the reworked hpd handling there'll be no downside to
unconditionally setting up the poll work any more.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 27 Jun 2013 08:40:23 +0000 (18:40 +1000)]
Merge branch 'drm/shmob' of git://linuxtv.org/pinchartl/fbdev into drm-next
Fixes for shmob + prime support
* 'drm/shmob' of git://linuxtv.org/pinchartl/fbdev:
drm/shmobile: Enable compilation on all ARM platforms
drm/shmobile: Add DRM PRIME support
drm/shmobile: Use devm_* managed functions
drm/shmobile: Minor typo fix in debug message
locking-selftests: Handle unexpected failures more strictly
When CONFIG_PROVE_LOCKING is not enabled, more tests are
expected to pass unexpectedly, but there no tests that should
start to fail that pass with CONFIG_PROVE_LOCKING enabled.
None of the ww_mutex codepaths should be taken in the 'normal'
mutex calls. The easiest way to verify this is by using the
normal mutex calls, and making sure o.ctx is unmodified.
Daniel Vetter [Thu, 20 Jun 2013 11:31:17 +0000 (13:31 +0200)]
mutex: Add w/w mutex slowpath debugging
Injects EDEADLK conditions at pseudo-random interval, with
exponential backoff up to UINT_MAX (to ensure that every lock
operation still completes in a reasonable time).
This way we can test the wound slowpath even for ww mutex users
where contention is never expected, and the ww deadlock
avoidance algorithm is only needed for correctness against
malicious userspace. An example would be protecting kernel
modesetting properties, which thanks to single-threaded X isn't
really expected to contend, ever.
I've looked into using the CONFIG_FAULT_INJECTION
infrastructure, but decided against it for two reasons:
- EDEADLK handling is mandatory for ww mutex users and should
never affect the outcome of a syscall. This is in contrast to -ENOMEM
injection. So fine configurability isn't required.
- The fault injection framework only allows to set a simple
probability for failure. Now the probability that a ww mutex acquire
stage with N locks will never complete (due to too many injected
EDEADLK backoffs) is zero. But the expected number of ww_mutex_lock
operations for the completely uncontended case would be O(exp(N)).
The per-acuiqire ctx exponential backoff solution choosen here only
results in O(log N) overhead due to injection and so O(log N * N)
lock operations. This way we can fail with high probability (and so
have good test coverage even for fancy backoff and lock acquisition
paths) without running into patalogical cases.
Note that EDEADLK will only ever be injected when we managed to
acquire the lock. This prevents any behaviour changes for users
which rely on the EALREADY semantics.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: dri-devel@lists.freedesktop.org Cc: linaro-mm-sig@lists.linaro.org Cc: rostedt@goodmis.org Cc: daniel@ffwll.ch Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20130620113117.4001.21681.stgit@patser Signed-off-by: Ingo Molnar <mingo@kernel.org>
Wound/wait mutexes are used when other multiple lock
acquisitions of a similar type can be done in an arbitrary
order. The deadlock handling used here is called wait/wound in
the RDBMS literature: The older tasks waits until it can acquire
the contended lock. The younger tasks needs to back off and drop
all the locks it is currently holding, i.e. the younger task is
wounded.
For full documentation please read Documentation/ww-mutex-design.txt.
References: https://lwn.net/Articles/548909/ Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Rob Clark <robdclark@gmail.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: dri-devel@lists.freedesktop.org Cc: linaro-mm-sig@lists.linaro.org Cc: rostedt@goodmis.org Cc: daniel@ffwll.ch Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/51C8038C.9000106@canonical.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
arch: Make __mutex_fastpath_lock_retval return whether fastpath succeeded or not
This will allow me to call functions that have multiple
arguments if fastpath fails. This is required to support ticket
mutexes, because they need to be able to pass an extra argument
to the fail function.
Originally I duplicated the functions, by adding
__mutex_fastpath_lock_retval_arg. This ended up being just a
duplication of the existing function, so a way to test if
fastpath was called ended up being better.
This also cleaned up the reservation mutex patch some by being
able to call an atomic_set instead of atomic_xchg, and making it
easier to detect if the wrong unlock function was previously
used.
Linus Torvalds [Tue, 25 Jun 2013 19:08:07 +0000 (09:08 -1000)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of last-minute fixes: a build regression for !SMP, a recent
memory detection patch caused kdump to break, a regression in regard
to sscanf vs reboot from FCP, and two fixes in the DMA mapping code
for PCI"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ipl: Fix FCP WWPN and LUN format strings for read
s390/mem_detect: fix memory hole handling
s390/dma: support debug_dma_mapping_error
s390/dma: fix mapping_error detection
s390/irq: Only define synchronize_irq() on SMP
Linus Torvalds [Tue, 25 Jun 2013 19:06:48 +0000 (09:06 -1000)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc bugfix from Ben Herrenschmidt:
"This is a fix for a regression causing a freescale "83xx" based
platforms to crash on boot due to some PCI breakage"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pci: Fix boot panic on mpc83xx (regression)
Linus Torvalds [Tue, 25 Jun 2013 06:17:11 +0000 (20:17 -1000)]
Merge tag 'spi-v3.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A few last minute SPI updates: fix a missized allocation and use
atomic allocations in atomic context in the PXA driver, and fix the
checking of return codes in the S3C64xx driver which caused spurious
errors under heavy load."
* tag 'spi-v3.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi/pxa2xx: fix memory corruption due to wrong size used in devm_kzalloc()
spi/pxa2xx: use GFP_ATOMIC in sg table allocation
spi: s3c64xx: Fix pm_runtime_get_sync() return value check
Daniel Vetter [Fri, 14 Jun 2013 22:13:16 +0000 (00:13 +0200)]
drm: fix fb leak in setcrtc
Drivers are allowed (actually have to) disable unrelated crtcs in
their ->set_config callback (when we steal all the connectors from
that crtc). If they do that they'll clear crtc->fb to NULL.
Which results in a refcount leak, since the drm core is keeping track
of that reference.
To fix this track the old fb of all crtcs and adjust references for
all of them. Of course, since we only hold an additional reference for
the fb for the current crtc we need to increase refcounts before we
drop the old one.
This approach has the benefit that it inches us a bit closer to an
atomic modeset world, where we want to update the config of all crtcs
in one step.
This regression has been introduce in the framebuffer refcount
conversion, specifically in
Reported-by: Russell King <linux@arm.linux.org.uk> Cc: Russell King <linux@arm.linux.org.uk> Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Vetter [Fri, 14 Jun 2013 22:13:15 +0000 (00:13 +0200)]
drm: check that ->set_config properly updates the fb
Historically drm lacked fb refcounting, so the updating of crtc->fb
was done by the lower levels at a point convenient to get their own
refcounting (e.g. refcounts for the underlying gem bo, pinning
refcounts) right. With the introduction of refcounted fbs the drm core
handled the fb refcounts, but still relied on drivers to update the
crtc->fb pointer (this approach required the least invasive changes in
drivers).
Enforce this contract with a WARN_ON.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Vetter [Fri, 14 Jun 2013 22:13:13 +0000 (00:13 +0200)]
drm/crtc-helper: explicit DPMS on after modeset
Atm the crtc helper implementation of set_config has really
inconsisten semantics: If just an fb update is good enough, dpms state
will be left as-is, but if we do a full modeset we force everything to
dpms on.
This change has already been applied to the i915 modeset code in
drm: Only set DPMS ON when actually configuring a mode
which fixed the bug of trying to dpms on disabled outputs, but
introduced the new discrepancy between an fb update only and full
modesets. The actual introduction of this goes back to
drm: Set connector DPMS status to ON in drm_crtc_helper_set_config
And if you'd dig around in the i915 driver code there's even more fun
around forcing dpms on and losing our heads and temper of the
resulting inconsistencies. Especially the DP re-training code had tons
of funny stuff in it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Vetter [Fri, 14 Jun 2013 22:13:12 +0000 (00:13 +0200)]
drm/crtc-helper: no need to check for fb->depth/bpp
... since we already check for fb->pixel_format, which encodes all
this. The other two fields are only for backwards compat of older
drivers (and we might want to look into eventually just killing them).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Vetter [Fri, 14 Jun 2013 22:13:11 +0000 (00:13 +0200)]
drm/crtc-helpers: Enforce sane set_config api
There's no point in trying to clean up after driver-bugs, so just blow
up. Furthermore it's an interface abuse to set no mode but have an fb
and aslo to try to set an fb without enough connectors. These two
spefici cases of interface abuse have been committed by the fb helper,
but that's been fixed meanwhile in
The i915 driver has been shipping since a while with these BUGs with
no reports, so should be save.
Note that this drops an ugly case where we clear crtc->fb behind the
upper levels back and so cause a refcounting mayhem, which Russell
Kins spotted while trying to hunt down a drm framebuffer leak.
Reported-by: Russell King <linux@arm.linux.org.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
powerpc/fsl-pci Make PCIe hotplug work with Freescale PCIe controllers
Up to now the PCIe link status on Freescale PCIe controllers was only
checked once at boot time. So hotplug did not work. With this patch the
link status is checked on every config read. PCIe devices not present at
boot time are found after doing 'echo 1 >/sys/bus/pci/rescan'.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes the issue by calling setup_indirect_pci for all device types.
fsl_indirect_read_config is now only used for booke/86xx PCIe controllers.
Reported-by: Michael Guntsche <mike@it-loops.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Signed-off-by: Scott Wood <scottwood@freescale.com>
Linus Torvalds [Sat, 22 Jun 2013 19:44:45 +0000 (09:44 -1000)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are two fixes that came in this week, one for a regression we
introduced in 3.10 in the GIC interrupt code, and the other one fixes
a typo in newly introduced code"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
irqchip: gic: call gic_cpu_init() as well in CPU_STARTING_FROZEN case
ARM: dts: Correct the base address of pinctrl_3 on Exynos5250
Linus Torvalds [Sat, 22 Jun 2013 19:02:44 +0000 (09:02 -1000)]
Merge tag 'driver-core-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg Kroah-Hartman:
"Here's a single patch for the firmware core that resolves a reported
oops in the firmware core that people have been hitting."
* tag 'driver-core-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
firmware loader: fix use-after-free by double abort
Linus Torvalds [Sat, 22 Jun 2013 19:01:47 +0000 (09:01 -1000)]
Merge tag 'usb-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are two USB patches for 3.10.
One updates the Kconfig wording for CONFIG_USB_PHY to make it,
hopefully, more obvious what this option is (I know you complained
about this when it hit the tree.) The other is a new device id for a
driver"
* tag 'usb-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: ti_usb_3410_5052: new device id for Abbot strip port cable
usb: phy: Improve Kconfig help for CONFIG_USB_PHY
Linus Torvalds [Sat, 22 Jun 2013 19:00:28 +0000 (09:00 -1000)]
Merge tag 'tty-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pul tty fixes from Greg Kroah-Hartman:
"Here are two tty core fixes that resolve some regressions that have
been reported recently. Both tiny fixes, but needed"
* tag 'tty-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix transient pty write() EIO
tty/vt: Return EBUSY if deallocating VT1 and it is busy
Pull SCSI target fixes from Nicholas Bellinger:
"Included is the recent tcm_qla2xxx residual underrun length fix from
Roland, along with Joern's iscsi-target patch for session_lock
breakage within iscsit_stop_time2retain_timer() code. Both are CC'ed
to stable.
The remaining two are specific to recent iscsi-target + iser
conversion changes. One drops some left-over debug noise, and Andy's
patch fixes configfs attribute handling during an explicit network
portal feature bit disable when iser-target is unsupported."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Remove left over v3.10-rc debug printks
target/iscsi: Fix op=disable + error handling cases in np_store_iser
tcm_qla2xxx: Fix residual for underrun commands that fail
target/iscsi: don't corrupt bh_count in iscsit_stop_time2retain_timer()
Linus Torvalds [Sat, 22 Jun 2013 18:43:17 +0000 (08:43 -1000)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Another set of fixes for Kernel 3.10.
This series contain:
- two Kbuild fixes for randconfig
- a buffer overflow when using rtl28xuu with r820t tuner
- one clk fixup on exynos4-is driver"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] Fix build when drivers are builtin and frontend modules
[media] s5p makefiles: don't override other selections on obj-[ym]
[media] exynos4-is: Fix FIMC-IS clocks initialization
[media] rtl28xxu: fix buffer overflow when probing Rafael Micro r820t tuner
Linus Torvalds [Sat, 22 Jun 2013 18:42:20 +0000 (08:42 -1000)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"Several fixes for bugs caught while looking through f_pos (ab)users"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
aout32 coredump compat fix
splice: don't pass the address of ->f_pos to methods
mconsole: we'd better initialize pos before passing it to vfs_read()...
Al Viro [Sat, 22 Jun 2013 07:01:38 +0000 (11:01 +0400)]
aout32 coredump compat fix
dump_seek() does SEEK_CUR, not SEEK_SET; native binfmt_aout
handles it correctly (seeks by PAGE_SIZE - sizeof(struct user),
getting the current position to PAGE_SIZE), compat one seeks
by PAGE_SIZE and ends up at PAGE_SIZE + already written...
Linus Torvalds [Fri, 21 Jun 2013 16:33:48 +0000 (06:33 -1000)]
Merge branch 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"This series fixes a couple of build failures, and fixes MTRR cleanup
and memory setup on very specific memory maps.
Finally, it fixes triggering backtraces on all CPUs, which was
inadvertently disabled on x86."
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Fix dummy variable buffer allocation
x86: Fix trigger_all_cpu_backtrace() implementation
x86: Fix section mismatch on load_ucode_ap
x86: fix build error and kconfig for ia32_emulation and binfmt
range: Do not add new blank slot with add_range_with_merge
x86, mtrr: Fix original mtrr range get for mtrr_cleanup
Linus Torvalds [Fri, 21 Jun 2013 16:33:06 +0000 (06:33 -1000)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm radeon fixes from Dave Airlie:
"One core fix, but mostly radeon fixes for s/r and big endian UVD
support, and a fix to stop the GPU being reset for no good reason, and
crashing people's machines."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: update lockup tracking when scheduling in empty ring
drm/prime: Honor requested file flags when exporting a buffer
drm/radeon: fix UVD on big endian
drm/radeon: fix write back suspend regression with uvd v2
drm/radeon: do not try to uselessly update virtual memory pagetable
Linus Torvalds [Fri, 21 Jun 2013 16:31:10 +0000 (06:31 -1000)]
Merge tag 'acpi-3.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
- Fix for a regression causing a failure to turn on some devices on
some systems during initialization introduced by a recent revert of
an ACPI PM change that broke something else. Fortunately, we know
exactly what devices are affected, so we can add a fix just for them
leaving everyone else alone.
- ACPI power resources initialization fix preventing a NULL pointer
from being dereferenced in the acpi_add_power_resource() error code
path.
- ACPI dock station driver fix that adds missing locking to
write_undock().
- ACPI resources allocation fix changing the scope of an old workaround
so that it doesn't affect systems that aren't actually buggy. This
was reported a couple of days ago to fix DMA problems on some new
platforms so we need it in -stable. From Mika Westerberg.
* tag 'acpi-3.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / LPSS: Power up LPSS devices during enumeration
ACPI / PM: Fix error code path for power resources initialization
ACPI / dock: Take ACPI scan lock in write_undock()
ACPI / resources: call acpi_get_override_irq() only for legacy IRQ resources
Linus Torvalds [Fri, 21 Jun 2013 16:29:22 +0000 (06:29 -1000)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Three one-line fixes for my first pull request; one for x86 host, one
for x86 guest, one for PPC"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86: kvmclock: zero initialize pvclock shared memory area
kvm/ppc/booke: Delay kvmppc_lazy_ee_enable
KVM: x86: remove vcpu's CPL check in host-invoked XCR set
Linus Torvalds [Fri, 21 Jun 2013 16:27:40 +0000 (06:27 -1000)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fix from Sage Weil:
"This fixes a problem preventing the kernel and userland librbd
libraries from sharing data with the new format 2 images"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use the correct length for format 2 object names
H. Peter Anvin [Fri, 21 Jun 2013 10:01:21 +0000 (03:01 -0700)]
Merge tag 'efi-urgent' into x86/urgent
* Don't leak random kernel memory to EFI variable NVRAM when attempting
to initiate garbage collection. Also, free the kernel memory when
we're done with it instead of leaking - Ben Hutchings
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Mika Westerberg [Thu, 20 Jun 2013 14:44:22 +0000 (17:44 +0300)]
spi/pxa2xx: fix memory corruption due to wrong size used in devm_kzalloc()
ACPI part of the driver accidentally used sizeof(*ssp) instead of the
correct sizeof(*pdata). This leads to nasty memory corruptions like the one
below:
Andy Grover [Wed, 29 May 2013 19:05:59 +0000 (12:05 -0700)]
target/iscsi: Fix op=disable + error handling cases in np_store_iser
Writing 0 when iser was not previously enabled, so succeed but do
nothing so that user-space code doesn't need a try: catch block
when ib_isert logic is not available.
Also, return actual error from add_network_portal using PTR_ERR
during op=enable failure.
Signed-off-by: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Dave Airlie [Thu, 20 Jun 2013 22:52:19 +0000 (08:52 +1000)]
Merge branch 'drm-fixes-3.10' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
One user visible fix to stop misreport GPU hangs and subsequent resets.
* 'drm-fixes-3.10' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: update lockup tracking when scheduling in empty ring
Jerome Glisse [Wed, 19 Jun 2013 14:02:28 +0000 (10:02 -0400)]
drm/radeon: update lockup tracking when scheduling in empty ring
There might be issue with lockup detection when scheduling on an
empty ring that have been sitting idle for a while. Thus update
the lockup tracking data when scheduling new work in an empty ring.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Tested-by: Andy Lutomirski <luto@amacapital.net> Cc: stable@vger.kernel.org Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Linus Torvalds [Thu, 20 Jun 2013 18:18:35 +0000 (08:18 -1000)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Two smaller fixes - plus a context tracking tracing fix that is a bit
bigger"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tracing/context-tracking: Add preempt_schedule_context() for tracing
sched: Fix clear NOHZ_BALANCE_KICK
sched/x86: Construct all sibling maps if smt
Linus Torvalds [Thu, 20 Jun 2013 18:17:36 +0000 (08:17 -1000)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Four fixes. The mmap ones are unfortunately larger than desired -
fuzzing uncovered bugs that needed perf context life time management
changes to fix properly"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix broken PEBS-LL support on SNB-EP/IVB-EP
perf: Fix mmap() accounting hole
perf: Fix perf mmap bugs
kprobes: Fix to free gone and unused optprobes
Linus Torvalds [Thu, 20 Jun 2013 18:16:07 +0000 (08:16 -1000)]
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull cpu idle fixes from Thomas Gleixner:
- Add a missing irq enable. Fallout of the idle conversion
- Fix stackprotector wreckage caused by the idle conversion
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
idle: Enable interrupts in the weak arch_cpu_idle() implementation
idle: Add the stack canary init to cpu_startup_entry()
Linus Torvalds [Thu, 20 Jun 2013 18:15:13 +0000 (08:15 -1000)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
- Fix inconstinant clock usage in virtual time accounting
- Fix a build error in KVM caused by the NOHZ work
- Remove a pointless timekeeping duty assignment which breaks NOHZ
- Use a proper notifier return value to avoid random behaviour
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Remove useless timekeeping duty attribution to broadcast source
nohz: Fix notifier return val that enforce timekeeping
kvm: Move guest entry/exit APIs to context_tracking
vtime: Use consistent clocks among nohz accounting
Linus Torvalds [Thu, 20 Jun 2013 18:08:46 +0000 (08:08 -1000)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fix fro, Benjamin Herrenschmidt:
"We accidentally broke hugetlbfs on Freescale embedded processors which
use a slightly different page table layout than our server processors"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix bad pmd error with book3E config
Linus Torvalds [Thu, 20 Jun 2013 18:07:42 +0000 (08:07 -1000)]
Merge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull tilepro fix from Chris Metcalf:
"This change allows the older tilepro architecture to be correctly
built by newer gccs, despite a change that caused gcc to start trying
to use an out-of-line implementation for __builtin_ffsll().
This should be inline again starting with gcc 4.7.4 and 4.8.2 or so,
but meanwhile this change keeps things from breaking, with the only
cost being a few bytes of code in the kernel to provide __ffsdi2 even
for compilers that do inline it"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tilepro: work around module link error with gcc 4.7
[media] Fix build when drivers are builtin and frontend modules
There are a large number of reports that the media build is
not compiling when some drivers are compiled as builtin, while
the needed frontends are compiled as module.
On the last one of such reports:
From: kbuild test robot <fengguang.wu@intel.com>
Subject: saa7134-dvb.c:undefined reference to `zl10039_attach'
The .config file has:
CONFIG_VIDEO_SAA7134=y
CONFIG_VIDEO_SAA7134_DVB=y
# CONFIG_MEDIA_ATTACH is not set
CONFIG_DVB_ZL10039=m
And it produces all those errors:
drivers/built-in.o: In function `set_type':
tuner-core.c:(.text+0x2f263e): undefined reference to `tea5767_attach'
tuner-core.c:(.text+0x2f273e): undefined reference to `tda9887_attach'
drivers/built-in.o: In function `tuner_probe':
tuner-core.c:(.text+0x2f2d20): undefined reference to `tea5767_autodetection'
drivers/built-in.o: In function `av7110_attach':
av7110.c:(.text+0x330bda): undefined reference to `ves1x93_attach'
av7110.c:(.text+0x330bf7): undefined reference to `stv0299_attach'
av7110.c:(.text+0x330c63): undefined reference to `tda8083_attach'
av7110.c:(.text+0x330d09): undefined reference to `ves1x93_attach'
av7110.c:(.text+0x330d33): undefined reference to `tda8083_attach'
av7110.c:(.text+0x330d5d): undefined reference to `stv0297_attach'
av7110.c:(.text+0x330dbe): undefined reference to `stv0299_attach'
drivers/built-in.o: In function `tuner_attach_dtt7520x':
ngene-cards.c:(.text+0x3381cb): undefined reference to `dvb_pll_attach'
drivers/built-in.o: In function `demod_attach_lg330x':
ngene-cards.c:(.text+0x33828a): undefined reference to `lgdt330x_attach'
drivers/built-in.o: In function `demod_attach_stv0900':
ngene-cards.c:(.text+0x3383d5): undefined reference to `stv090x_attach'
drivers/built-in.o: In function `cineS2_probe':
ngene-cards.c:(.text+0x338b7f): undefined reference to `drxk_attach'
drivers/built-in.o: In function `configure_tda827x_fe':
saa7134-dvb.c:(.text+0x346ae7): undefined reference to `tda10046_attach'
drivers/built-in.o: In function `dvb_init':
saa7134-dvb.c:(.text+0x347283): undefined reference to `mt352_attach'
saa7134-dvb.c:(.text+0x3472cd): undefined reference to `mt352_attach'
saa7134-dvb.c:(.text+0x34731c): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x34733c): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x34735c): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x347378): undefined reference to `tda10046_attach'
saa7134-dvb.c:(.text+0x3473db): undefined reference to `tda10046_attach'
drivers/built-in.o:saa7134-dvb.c:(.text+0x347502): more undefined references to `tda10046_attach' follow
drivers/built-in.o: In function `dvb_init':
saa7134-dvb.c:(.text+0x347812): undefined reference to `mt352_attach'
saa7134-dvb.c:(.text+0x347951): undefined reference to `mt312_attach'
saa7134-dvb.c:(.text+0x3479a9): undefined reference to `mt312_attach'
>> saa7134-dvb.c:(.text+0x3479c1): undefined reference to `zl10039_attach'
This is happening because a builtin module can't use directly a symbol
found on a module. By enabling CONFIG_MEDIA_ATTACH, the configuration
becomes valid, as dvb_attach() macro loads the module if needed, making
the symbol available to the builtin module.
While this bug started to appear after the patches that use IS_DEFINED
macro (like changeset 7b34be71db533f3e0cf93d53cf62d036cdb5418a), this
bug is a way ancient than that.
The thing is that, before the IS_DEFINED() patches, the logic used to be:
The above code, with the .config file used, was evoluting to FALSE
(instead of TRUE as it should be, as CONFIG_DVB_ZL10039 is 'm'),
and were adding the static inline code at saa7134-dvb, instead
of the external call. So, while it weren't producing any compilation
error, the code weren't working either.
So, as the overhead for using CONFIG_MEDIA_ATTACH is minimal, just
enable it, if MODULES is defined.
Shawn Guo [Wed, 12 Jun 2013 11:30:27 +0000 (19:30 +0800)]
irqchip: gic: call gic_cpu_init() as well in CPU_STARTING_FROZEN case
Commit c011470 (irqchip: gic: Perform the gic_secondary_init() call via
CPU notifier) moves gic_secondary_init() that used to be called in
.smp_secondary_init hook into a notifier call. But it changes the
system behavior a little bit. Before the commit, gic_cpu_init()
is called not only when kernel brings up the secondary cores but also
when system resuming procedure hot-plugs the cores back to kernel.
While after the commit, the function will not be called in the latter
case, where the 'action' will not be CPU_STARTING but
CPU_STARTING_FROZEN. This behavior difference at least causes the
following suspend/resume regression on imx6q.
$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
mmc1: card e624 removed
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
PM: Entering mem sleep
PM: suspend of devices complete after 5.930 msecs
PM: suspend devices took 0.010 seconds
PM: late suspend of devices complete after 0.343 msecs
PM: noirq suspend of devices complete after 0.828 msecs
Disabling non-boot CPUs ...
CPU1: shutdown
CPU2: shutdown
CPU3: shutdown
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
INFO: rcu_sched detected stalls on CPUs/tasks: { 1 2 3} (detected by 0, t=2102 jiffies, g=4294967169, c=4294967168, q=17)
Task dump for CPU 1:
swapper/1 R running 0 0 1 0x00000000
Backtrace:
[<bf895ff4>] (0xbf895ff4) from [<00000000>] ( (null))
Backtrace aborted due to bad frame pointer <8007ccdc>
Task dump for CPU 2:
swapper/2 R running 0 0 1 0x00000000
Backtrace:
[<8075dbdc>] (0x8075dbdc) from [<00000000>] ( (null))
Backtrace aborted due to bad frame pointer <00000002>
Task dump for CPU 3:
swapper/3 R running 0 0 1 0x00000000
Backtrace:
[<8075dbdc>] (0x8075dbdc) from [<00000000>] ( (null))
Fix the regression by checking 'action' being CPU_STARTING_FROZEN to
have gic_cpu_init() called for secondary cores when system resumes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Tested-by: Joseph Lo <josephl@nvidia.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The following change fixes the x86 implementation of
trigger_all_cpu_backtrace(), which was previously (accidentally,
as far as I can tell) disabled to always return false as on
architectures that do not implement this function.
trigger_all_cpu_backtrace(), as defined in include/linux/nmi.h,
should call arch_trigger_all_cpu_backtrace() if available, or
return false if the underlying arch doesn't implement this
function.
x86 did provide a suitable arch_trigger_all_cpu_backtrace()
implementation, but it wasn't actually being used because it was
declared in asm/nmi.h, which linux/nmi.h doesn't include. Also,
linux/nmi.h couldn't easily be fixed by including asm/nmi.h,
because that file is not available on all architectures.
I am proposing to fix this by moving the x86 definition of
arch_trigger_all_cpu_backtrace() to asm/irq.h.
Tested via: echo l > /proc/sysrq-trigger
Before the change, this uses a fallback implementation which
shows backtraces on active CPUs (using
smp_call_function_interrupt() )
After the change, this shows NMI backtraces on all CPUs
Jed Davis [Thu, 20 Jun 2013 03:07:14 +0000 (04:07 +0100)]
perf: arm64: Record the user-mode PC in the call chain.
With this change, we no longer lose the innermost entry in the user-mode
part of the call chain. See also the x86 port, which includes the ip,
and the corresponding change in arch/arm.
Signed-off-by: Jed Davis <jld@mozilla.com> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: Will Deacon <will.deacon@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[media] s5p makefiles: don't override other selections on obj-[ym]
The $obj-m/$obj-y vars should be adding new modules to build, not
overriding it. So, it should never use
$obj-y := foo.o
instead, it should use:
$obj-y += foo.o
Failing to do that is very bad, as it will suppress needed modules.
Book3E uses the hugepd at PMD level and don't encode pte directly
at the pmd level. So it will find the lower bits of pmd set
and the pmd_bad check throws error. Infact the current code
will never take the free_hugepd_range call at all because it will
clear the pmd if it find a hugepd pointer. Fix this by clearing
bad pmd only if it is not a hugepd pointer.
Benoit Parrot [Tue, 18 Jun 2013 22:18:31 +0000 (17:18 -0500)]
gpu:drm:tilcdc: get preferred_bpp value from DT
The preferred_bpp value in currently hard-coded to 16.
This causes color corruption on the am335x-evm lcd panel which
requires 32 bpp instead. This changes attempts to use the configured
bpp value from the DT or built-in panel-info struct.
Signed-off-by: Benoit Parrot <bparrot@ti.com> Acked-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
ACPI / LPSS: Power up LPSS devices during enumeration
Commit 7cd8407 (ACPI / PM: Do not execute _PS0 for devices without
_PSC during initialization) introduced a regression on some systems
with Intel Lynxpoint Low-Power Subsystem (LPSS) where some devices
need to be powered up during initialization, but their device objects
in the ACPI namespace have _PS0 and _PS3 only (without _PSC or power
resources).
To work around this problem, make the ACPI LPSS driver power up
devices it knows about by using a new helper function
acpi_device_fix_up_power() that does all of the necessary
sanity checks and calls acpi_dev_pm_explicit_set() to put the
device into D0.
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI / PM: Fix error code path for power resources initialization
Commit 781d737 (ACPI: Drop power resources driver) introduced a
bug in the power resources initialization error code path causing
a NULL pointer to be referenced in acpi_release_power_resource()
if there's an error triggering a jump to the 'err' label in
acpi_add_power_resource(). This happens because the list_node
field of struct acpi_power_resource has not been initialized yet
at this point and doing a list_del() on it is a bad idea.
To prevent this problem from occuring, initialize the list_node
field of struct acpi_power_resource upfront.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: 3.9+ <stable@vger.kernel.org> Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
ACPI / dock: Take ACPI scan lock in write_undock()
Since commit 3757b94 (ACPI / hotplug: Fix concurrency issues and
memory leaks) acpi_bus_scan() and acpi_bus_trim() must always be
called under acpi_scan_lock, but currently the following scenario
violating that requirement is possible:
Fix that by making write_undock() acquire acpi_scan_lock before
calling handle_eject_request() as appropriate (begin_undock() is
under the lock too in analogy with acpi_dock_deferred_cb()).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: 3.9+ <stable@vger.kernel.org> Acked-by: Toshi Kani <toshi.kani@hp.com>
Mika Westerberg [Mon, 20 May 2013 15:41:45 +0000 (15:41 +0000)]
ACPI / resources: call acpi_get_override_irq() only for legacy IRQ resources
acpi_get_override_irq() was added because there was a problem with
buggy BIOSes passing wrong IRQ() resource for the RTC IRQ. The
commit that added the workaround was 61fd47e0c8476 (ACPI: fix two
IRQ8 issues in IOAPIC mode).
With ACPI 5 enumerated devices there are typically one or more
extended IRQ resources per device (and these IRQs can be shared).
However, the acpi_get_override_irq() workaround forces all IRQs in
range 0 - 15 (the legacy ISA IRQs) to be edge triggered, active high
as can be seen from the dmesg below:
ACPI: IRQ 6 override to edge, high
ACPI: IRQ 7 override to edge, high
ACPI: IRQ 7 override to edge, high
ACPI: IRQ 13 override to edge, high
Also /proc/interrupts for the I2C controllers (INT33C2 and INT33C3) shows
the same thing:
7: 4 0 0 0 IO-APIC-edge INT33C2:00, INT33C3:00
The _CSR method for INT33C2 (and INT33C3) device returns following
resource:
which states that this is supposed to be level triggered, active low,
shared IRQ instead.
Fix this by making sure that acpi_get_override_irq() gets only called
when we are dealing with legacy IRQ() or IRQNoFlags() descriptors.
While we are there, correct pr_warning() to print the right triggering
value.
This change turns out to be necessary to make DMA work correctly on
systems based on the Intel Lynxpoint PCH (Platform Controller Hub).
[rjw: Changelog] Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: 3.9+ <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Paul Gortmaker [Wed, 19 Jun 2013 15:15:26 +0000 (11:15 -0400)]
x86: Fix section mismatch on load_ucode_ap
We are in the process of removing all the __cpuinit annotations.
While working on making that change, an existing problem was
made evident:
WARNING: arch/x86/kernel/built-in.o(.text+0x198f2): Section mismatch
in reference from the function cpu_init() to the function
.init.text:load_ucode_ap() The function cpu_init() references
the function __init load_ucode_ap(). This is often because cpu_init
lacks a __init annotation or the annotation of load_ucode_ap is wrong.
This now appears because in my working tree, cpu_init() is no longer
tagged as __cpuinit, and so the audit picks up the mismatch. The 2nd
hypothesis from the audit is the correct one, as there was an incorrect
__init tag on the prototype in the header (but __cpuinit was used on
the function itself.)
The audit is telling us that the prototype's __init annotation took
effect and the function did land in the .init.text section. Checking
with objdump on a mainline tree that still has __cpuinit shows that
the __cpuinit on the function takes precedence over the __init on the
prototype, but that won't be true once we make __cpuinit a no-op.
Even though we are removing __cpuinit, we temporarily align both
the function and the prototype on __cpuinit so that the changeset
can be applied to stable trees if desired.
[ hpa: build fix only, no object code change ]
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: stable <stable@vger.kernel.org> # 3.9+ Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Link: http://lkml.kernel.org/r/1371654926-11729-1-git-send-email-paul.gortmaker@windriver.com Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
David Daney [Mon, 17 Jun 2013 15:46:07 +0000 (08:46 -0700)]
mn10300: Fix include dependency in irqflags.h et al.
We need to pick up the definition of raw_smp_processor_id() from
asm/smp.h. For the !SMP case, we need to supply a definition of
raw_smp_processor_id().
Because of the include dependencies we cannot use smp_call_func_t in
asm/smp.h, but we do need linux/thread_info.h
Signed-off-by: David Daney <david.daney@cavium.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull sparc fixes from David Miller:
"Various sparc bug fixes, in particular:
1) TSB hashes have to be flushed before TLB on sparc64, from Dave
Kleikamp.
2) LEON timer interrupts can get stuck, from Andreas Larsson.
3) Sparc64 needs to handle lack of address-congruence devicetree
property, from Bob Picco"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: tsb must be flushed before tlb
sparc,leon: Convert to use devm_ioremap_resource
sparc64 address-congruence property
sparc32, leon: Enable interrupts before going idle to avoid getting stuck
sparc32, leon: Remove separate "ticker" timer for SMP
sparc: kernel: using strlcpy() instead of strcpy()
arch: sparc: prom: looping issue, need additional length check in the outside looping
sparc: remove inline marking of EXPORT_SYMBOL functions
sparc: Switch to asm-generic/linkage.h
Linus Torvalds [Wed, 19 Jun 2013 16:23:56 +0000 (06:23 -1000)]
Merge branch 'parisc-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"This contains a kernel segfault fix when reading /proc/kpageflags or
/proc/kpagecount, two fixes for the serial port and PCI graphic card
support on C8000 workstations and a fix to use unshadowed registers
for flushing D- and I-caches."
* 'parisc-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Use unshadowed index register for flush instructions in flush_dcache_page_asm and flush_icache_page_asm
parisc: provide pci_mmap_page_range() for parisc
parisc: fix serial ports on C8000 workstation
parisc: fix kernel BUG at arch/parisc/include/asm/mmzone.h:50 (part 2)
James Hogan [Fri, 14 Jun 2013 09:31:01 +0000 (10:31 +0100)]
metag: fix mm/hugetlb.c build breakage
Commit 106c992a5ebe ("mm/hugetlb: add more arch-defined huge_pte
functions") added an include of <asm-generic/hugetlb.h> to each
architecture's <asm/hugetlb.h> (except s390). Unfortunately metag was
missed which resulted in build errors when hugetlbfs is enabled (see
below).
Add the include for metag too to fix the build errors:
mm/hugetlb.c In function 'make_huge_pte':
mm/hugetlb.c +2250 : error: implicit declaration of function 'huge_pte_mkwrite'
mm/hugetlb.c +2250 : error: implicit declaration of function 'huge_pte_mkdirty'
...
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Michal Hocko <mhocko@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 19 Jun 2013 16:19:46 +0000 (06:19 -1000)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"The larger changes this time are
- "ARM: 7755/1: handle user space mapped pages in flush_kernel_dcache_page"
which fixes more data corruption problems with O_DIRECT
- "ARM: 7759/1: decouple CPU offlining from reboot/shutdown" which
gets us back to working shutdown/reboot on SMP platforms
- "ARM: 7752/1: errata: LoUIS bit field in CLIDR register is incorrect"
which fixes a shutdown regression found in v3.10 on Versatile
Express platforms.
The remainder are the quite small, maybe one or two line changes"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7759/1: decouple CPU offlining from reboot/shutdown
ARM: 7756/1: zImage/virt: remove hyp-stub.S during distclean
ARM: 7755/1: handle user space mapped pages in flush_kernel_dcache_page
ARM: 7754/1: Fix the CPU ID and the mask associated to the PJ4B
ARM: 7753/1: map_init_section flushes incorrect pmd
ARM: 7752/1: errata: LoUIS bit field in CLIDR register is incorrect
Heiko Carstens [Wed, 19 Jun 2013 07:16:54 +0000 (09:16 +0200)]
s390/mem_detect: fix memory hole handling
With git commit 996b4a7d "s390/mem_detect: remove artificial kdump
memory types" the memory detection code got simplified.
As a side effect the array that describes memory chunks may now
contain empty (zeroed) entries.
All call sites can handle this except for
drivers/s390/char/zcore.c::zcore_memmap_open
which has a really odd user space interface. The easiest fix is to
change the memory hole handling code, so that no empty entries exist
before the last valid entry is reached.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ISP clock register content is not preserved over the ISP power domain
off/on cycle. Instead of setting the clock frequencies once at probe time
the clock rates set up is moved to the runtime_resume handler, which is
invoked after the related power domain is already enabled, ensuring the
clocks are properly configured when the device is actively used.
This fixes the FIMC-IS malfunctions and STREAM ON timeout errors accuring
on some boards:
[ 59.860000] fimc_is_general_irq_handler:583 ISR_NDONE: 5: 0x800003e8, IS_ERROR_UNKNOWN
[ 59.860000] fimc_is_general_irq_handler:586 IS_ERROR_TIME_OUT
Steven Rostedt [Fri, 24 May 2013 19:23:40 +0000 (15:23 -0400)]
tracing/context-tracking: Add preempt_schedule_context() for tracing
Dave Jones hit the following bug report:
===============================
[ INFO: suspicious RCU usage. ]
3.10.0-rc2+ #1 Not tainted
-------------------------------
include/linux/rcupdate.h:771 rcu_read_lock() used illegally while idle!
other info that might help us debug this:
RCU used illegally from idle CPU! rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
2 locks held by cc1/63645:
#0: (&rq->lock){-.-.-.}, at: [<ffffffff816b39fd>] __schedule+0xed/0x9b0
#1: (rcu_read_lock){.+.+..}, at: [<ffffffff8109d645>] cpuacct_charge+0x5/0x1f0
What happened was that the function tracer traced the schedule_user() code
that tells RCU that the system is coming back from userspace, and to
add the CPU back to the RCU monitoring.
Because the function tracer does a preempt_disable/enable_notrace() calls
the preempt_enable_notrace() checks the NEED_RESCHED flag. If it is set,
then preempt_schedule() is called. But this is called before the user_exit()
function can inform the kernel that the CPU is no longer in user mode and
needs to be accounted for by RCU.
The fix is to create a new preempt_schedule_context() that checks if
the kernel is still in user mode and if so to switch it to kernel mode
before calling schedule. It also switches back to user mode coming back
from schedule in need be.
The only user of this currently is the preempt_enable_notrace(), which is
only used by the tracing subsystem.
Vincent Guittot [Wed, 5 Jun 2013 08:13:11 +0000 (10:13 +0200)]
sched: Fix clear NOHZ_BALANCE_KICK
I have faced a sequence where the Idle Load Balance was sometime not
triggered for a while on my platform, in the following scenario:
CPU 0 and CPU 1 are running tasks and CPU 2 is idle
CPU 1 kicks the Idle Load Balance
CPU 1 selects CPU 2 as the new Idle Load Balancer
CPU 2 sets NOHZ_BALANCE_KICK for CPU 2
CPU 2 sends a reschedule IPI to CPU 2
While CPU 3 wakes up, CPU 0 or CPU 1 migrates a waking up task A on CPU 2
CPU 2 finally wakes up, runs task A and discards the Idle Load Balance
task A quickly goes back to sleep (before a tick occurs on CPU 2)
CPU 2 goes back to idle with NOHZ_BALANCE_KICK set
Whenever CPU 2 will be selected as the ILB, no reschedule IPI will be sent
because NOHZ_BALANCE_KICK is already set and no Idle Load Balance will be
performed.
We must wait for the sched softirq to be raised on CPU 2 thanks to another
part the kernel to come back to clear NOHZ_BALANCE_KICK.
The proposed solution clears NOHZ_BALANCE_KICK in schedule_ipi if
we can't raise the sched_softirq for the Idle Load Balance.
Change since V1:
- move the clear of NOHZ_BALANCE_KICK in got_nohz_idle_kick if the ILB
can't run on this CPU (as suggested by Peter)
perf/x86: Fix broken PEBS-LL support on SNB-EP/IVB-EP
This patch fixes broken support of PEBS-LL on SNB-EP/IVB-EP.
For some reason, the LDLAT extra reg definition for snb_ep
showed up as duplicate in the snb table.
This patch moves the definition of LDLAT back into the
snb_ep table.
Peter Zijlstra [Tue, 4 Jun 2013 08:44:21 +0000 (10:44 +0200)]
perf: Fix mmap() accounting hole
Vince's fuzzer once again found holes. This time it spotted a leak in
the locked page accounting.
When an event had redirected output and its close() was the last
reference to the buffer we didn't have a vm context to undo accounting.
Change the code to destroy the buffer on the last munmap() and detach
all redirected events at that time. This provides us the right context
to undo the vm accounting.
projects / linux-beck.git / log