Patrick McHardy [Fri, 5 Apr 2013 08:13:30 +0000 (08:13 +0000)]
netfilter: nf_ct_sip: don't drop packets with offsets pointing outside the packet
Some Cisco phones create huge messages that are spread over multiple packets.
After calculating the offset of the SIP body, it is validated to be within
the packet and the packet is dropped otherwise. This breaks operation of
these phones. Since connection tracking is supposed to be passive, just let
those packets pass unmodified and untracked.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
1) Fix erroneous sock_orphan() leading to crashes and double
kfree_skb() in NFC protocol. From Thierry Escande and Samuel Ortiz.
2) Fix use after free in remain-on-channel mac80211 code, from Johannes
Berg.
3) nf_reset() needs to reset the NF tracing cookie, otherwise we can
leak it from one namespace into another. Fix from Gao Feng and
Patrick McHardy.
4) Fix overflow in channel scanning array of mwifiex driver, from Stone
Piao.
5) Fix loss of link after suspend/shutdown in r8169, from Hayes Wang.
6) Synchronization of unicast address lists to the undelying device
doesn't work because whether to sync is maintained as a boolean
rather than a true count. Fix from Vlad Yasevich.
7) Fix corruption of TSO packets in atl1e by limiting the segmented
packet length. From Hannes Frederic Sowa.
8) Revert bogus AF_UNIX credential passing change and fix the
coalescing issue properly, from Eric W Biederman.
9) Changes of ipv4 address lifetime settings needs to generate a
notification, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
netfilter: don't reset nf_trace in nf_reset()
net: ipv4: notify when address lifetime changes
ixgbe: fix registration order of driver and DCA nofitication
af_unix: If we don't care about credentials coallesce all messages
Revert "af_unix: dont send SCM_CREDENTIAL when dest socket is NULL"
bonding: remove sysfs before removing devices
atl1e: limit gso segment size to prevent generation of wrong ip length fields
net: count hw_addr syncs so that unsync works properly.
r8169: fix auto speed down issue
netfilter: ip6t_NPT: Fix translation for non-multiple of 32 prefix lengths
mwifiex: limit channel number not to overflow memory
NFC: microread: Fix build failure due to a new MEI bus API
iwlwifi: dvm: fix the passive-no-RX workaround
netfilter: nf_conntrack: fix error return code
NFC: llcp: Keep the connected socket parent pointer alive
mac80211: fix idle handling sequence
netfilter: nfnetlink_acct: return -EINVAL if object name is empty
netfilter: nfnetlink_queue: fix error return code in nfnetlink_queue_init()
netfilter: reset nf_trace in nf_reset
mac80211: fix remain-on-channel cancel crash
...
Patrick McHardy [Fri, 5 Apr 2013 18:42:05 +0000 (20:42 +0200)]
netfilter: don't reset nf_trace in nf_reset()
Commit 130549fe ("netfilter: reset nf_trace in nf_reset") added code
to reset nf_trace in nf_reset(). This is wrong and unnecessary.
nf_reset() is used in the following cases:
- when passing packets up the the socket layer, at which point we want to
release all netfilter references that might keep modules pinned while
the packet is queued. nf_trace doesn't matter anymore at this point.
- when encapsulating or decapsulating IPsec packets. We want to continue
tracing these packets after IPsec processing.
- when passing packets through virtual network devices. Only devices on
that encapsulate in IPv4/v6 matter since otherwise nf_trace is not
used anymore. Its not entirely clear whether those packets should
be traced after that, however we've always done that.
- when passing packets through virtual network devices that make the
packet cross network namespace boundaries. This is the only cases
where we clearly want to reset nf_trace and is also what the
original patch intended to fix.
Add a new function nf_reset_trace() and use it in dev_forward_skb() to
fix this properly.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Fixes for a number of small glitches in various corners of the MIPS
tree. No particular areas is standing out.
With this applied all MIPS defconfigs are building fine. No merge
conflicts are expected."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Delete definition of SA_RESTORER.
MIPS: Fix ISA level which causes secondary cache init bypassing and more
MIPS: Fix build error cavium-octeon without CONFIG_SMP
MIPS: Kconfig: Rename SNIPROM too
MIPS: Alchemy: Fix typo "CONFIG_DEBUG_PCI"
MIPS: Unbreak function tracer for 64-bit kernel.
Pull GFS2 fixes from Steven Whitehouse:
"There are two patches which fix up a couple of minor issues in the DLM
interface code, a missing error path in gfs2_rs_alloc(), one patch
which fixes a problem during "withdraw" and a fix for discards/FITRIM
when using 4k sector sized devices."
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Issue discards in 512b sectors
GFS2: Fix unlock of fcntl locks during withdrawn state
GFS2: return error if malloc failed in gfs2_rs_alloc()
GFS2: use memchr_inv
GFS2: use kmalloc for lvb bitmap
Merge tag 'spi-fix-v3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi fixes from Mark Brown:
"A bunch of small driver fixes plus a fix for error handling in the
core - nothing too exciting overall."
* tag 'spi-fix-v3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi/mpc512x-psc: optionally keep PSC SS asserted across xfer segmensts
spi: Unlock a spinlock before calling into the controller driver.
spi/s3c64xx: modified error interrupt handling and init
spi/bcm63xx: don't disable non enabled clocks in probe error path
spi/bcm63xx: Remove unused variable
spi: slink-tegra20: move runtime pm calls to transfer_one_message
Bob Peterson [Fri, 22 Mar 2013 14:07:24 +0000 (10:07 -0400)]
GFS2: Issue discards in 512b sectors
This patch changes GFS2's discard issuing code so that it calls
function sb_issue_discard rather than blkdev_issue_discard. The
code was calling blkdev_issue_discard and specifying the correct
sector offset and sector size, but blkdev_issue_discard expects
these values to be in terms of 512 byte sectors, even if the native
sector size for the device is different. Calling sb_issue_discard
with the BLOCK size instead ensures the correct block-to-512b-sector
translation. I verified that "minlen" is specified in blocks, so
comparing it to a number of blocks is correct.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch introduced a few races which cannot be easily fixed with a
small follow-up patch. Furthermore, the SoC with the broken hardware
register, which this patch intended to add support for, can only be used
with device trees, which this driver currently does not support.
[ Here is the discussion that led to this "revert" patch:
https://lkml.org/lkml/2013/4/3/176 ]
Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'fbdev-fixes-3.9-rc6' of git://gitorious.org/linux-omap-dss2/linux
Pull fbdev fixes from Tomi Valkeinen:
"Fix uvesafb crash bug and typoed flag name in fbmon's new videomode
code"
* tag 'fbdev-fixes-3.9-rc6' of git://gitorious.org/linux-omap-dss2/linux:
video:uvesafb: Fix dereference NULL pointer code path
fbmon: use VESA_DMT_VSYNC_HIGH to fix typo
Merge tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains slightly more volumes than usual at this stage, mostly
because of my vacation in the last week. Nothing to scare, all small
and/or trivial fixes:
- Fix loop path handling in ASoC DAPM
- Some memory handling fixes in ASoC core
- Fix spear_pcm to adapt to the updated API
- HD-audio HDMI ELD handling fixes
- Fix for CM6331 USB-audio SRC change bugs
- Revert power_save_controller option change due to user-space usage
- A few other small ASoC and HD-audio fixes"
* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/generic - fix uninitialized variable
Revert "ALSA: hda - Allow power_save_controller option override DCAPS"
ALSA: hda - fix typo in proc output
ALSA: hda - Enabling Realtek ALC 671 codec
ALSA: usb: Work around CM6631 sample rate change bug
ALSA: hda - bug fix on HDMI ELD debug message
ALSA: hda - bug fix on return value when getting HDMI ELD info
ASoC: dma-sh7760: Fix compile error
ASoC: core: fix invalid free of devm_ allocated data
ASoC: spear_pcm: Update to new pcm_new() API
ASoC:: max98090: Remove executable bit
ASoC: dapm: Fix pointer dereference in is_connected_output_ep()
ASoC: pcm030 audio fabric: remove __init from probe
ASoC: imx-ssi: Fix occasional AC97 reset failure
ASoC: core: fix possible memory leak in snd_soc_bytes_put()
ASoC: wm_adsp: fix possible memory leak in wm_adsp_load_coeff()
ASoC: dapm: Fix handling of loops
ASoC: si476x: Add missing break for SNDRV_PCM_FORMAT_S8 switch case
Ralf Baechle [Mon, 25 Mar 2013 12:43:14 +0000 (13:43 +0100)]
MIPS: Delete definition of SA_RESTORER.
SA_RESTORER used to be defined as 0x04000000 but only the O32 ABI ever
supported its use and no libc was using it, so the entire sa-restorer
functionality was removed with lmo commit 39bffc12c3580ab [Zap sa_restorer.]
for 2.5.48 retaining only the SA_RESTORER definition as a reminder to avoid
accidental reuse of the mask bit.
Upstream cdef9602fbf1871a43f0f1b5cea10dd0f275167d [signal: always clear
sa_restorer on execve] adds code that assumes sa_sigaction has an
sa_restorer field, if SA_RESTORER is defined which would break MIPS.
So remove the SA_RESTORER definition before the v3.8.4 merge.
MIPS: Fix ISA level which causes secondary cache init bypassing and more
The commit a96102be70 introduced set_isa() where compatible ISA info is
also set aside from the one gets passed in. It means, for example, 1004K
will have MIPS_CPU_ISA_M32R2/M32R1/II/I flags. This leads to things like
the following inappropriate:
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Bolle [Thu, 4 Apr 2013 12:47:01 +0000 (12:47 +0000)]
MIPS: Alchemy: Fix typo "CONFIG_DEBUG_PCI"
Commit 7517de348663b08a808aff44b5300e817157a568 ("MIPS: Alchemy: Redo
PCI as platform driver") added a reference to CONFIG_DEBUG_PCI. Change
it to CONFIG_PCI_DEBUG, as that is a valid Kconfig macro.
Also add a newline to a debugging printk that this fix enables.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 2 Apr 2013 22:59:29 +0000 (22:59 +0000)]
MIPS: Unbreak function tracer for 64-bit kernel.
Commit 58b69401c797 [MIPS: Function tracer: Fix broken function tracing]
completely broke the function tracer for 64-bit kernels. The symptom is
a system hang very early in the boot process.
The fix: Remove/fix $sp adjustments for 64-bit case.
Signed-off-by: David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Cc: Al Cooper <alcooperx@gmail.com> Cc: viric@viric.name Cc: stable@vger.kernel.org # 3.8.x Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Jakub Kicinski [Wed, 3 Apr 2013 16:50:54 +0000 (16:50 +0000)]
ixgbe: fix registration order of driver and DCA nofitication
ixgbe_notify_dca cannot be called before driver registration
because it expects driver's klist_devices to be allocated and
initialized. While on it make sure debugfs files are removed
when registration fails.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
af_unix: If we don't care about credentials coallesce all messages
It was reported that the following LSB test case failed
https://lsbbugs.linuxfoundation.org/attachment.cgi?id=2144 because we
were not coallescing unix stream messages when the application was
expecting us to.
The problem was that the first send was before the socket was accepted
and thus sock->sk_socket was NULL in maybe_add_creds, and the second
send after the socket was accepted had a non-NULL value for sk->socket
and thus we could tell the credentials were not needed so we did not
bother.
The unnecessary credentials on the first message cause
unix_stream_recvmsg to start verifying that all messages had the same
credentials before coallescing and then the coallescing failed because
the second message had no credentials.
Ignoring credentials when we don't care in unix_stream_recvmsg fixes a
long standing pessimization which would fail to coallesce messages when
reading from a unix stream socket if the senders were different even if
we did not care about their credentials.
I have tested this and verified that the in the LSB test case mentioned
above that the messages do coallesce now, while the were failing to
coallesce without this change.
Reported-by: Karel Srot <ksrot@redhat.com> Reported-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The problem that the above patch was meant to address is that af_unix
messages are not being coallesced because we are sending unnecesarry
credentials. Not sending credentials in maybe_add_creds totally
breaks unconnected unix domain sockets that wish to send credentails
to other sockets.
In practice this break some versions of udev because they receive a
message and the sending uid is bogus so they drop the message.
Reported-by: Sven Joachim <svenjoac@gmx.de> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We have a race condition if we try to rmmod bonding and simultaneously add
a bond master through sysfs. In bonding_exit() we first remove the devices
(through rtnl_link_unregister() ) and only after that we remove the sysfs.
If we manage to add a device through sysfs after that the devices were
removed - we'll end up with that device/sysfs structure and with the module
unloaded.
Fix this by first removing the sysfs and only after that calling
rtnl_link_unregister().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
atl1e: limit gso segment size to prevent generation of wrong ip length fields
The limit of 0x3c00 is taken from the windows driver.
Suggested-by: Huang, Xiong <xiong@qca.qualcomm.com> Cc: Huang, Xiong <xiong@qca.qualcomm.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: count hw_addr syncs so that unsync works properly.
A few drivers use dev_uc_sync/unsync to synchronize the
address lists from master down to slave/lower devices. In
some cases (bond/team) a single address list is synched down
to multiple devices. At the time of unsync, we have a leak
in these lower devices, because "synced" is treated as a
boolean and the address will not be unsynced for anything after
the first device/call.
Treat "synced" as a count (same as refcount) and allow all
unsync calls to work.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'pm+acpi-3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Revert of a recent cpuidle change that caused Nehalem machines to
hang on boot from Alex Shi.
- USB power management fix addressing a crash in the port device
object's release routine from Rafael J Wysocki.
- Device PM QoS fix for a potential deadlock related to sysfs interface
from Rafael J Wysocki.
- Fix for a cpufreq crash when the /cpus Device Tree node is missing
from Paolo Pisati.
- Fix for a build issue on ia64 related to the Boot Graphics Resource
Table (BGRT) from Tony Luck.
- Two fixes for ACPI handles being set incorrectly for device objects
that don't correspond to any ACPI namespace nodes in the I2C and SPI
subsystems from Rafael J Wysocki.
- Fix for compiler warnings related to CONFIG_PM_DEVFREQ being unset
from Rajagopal Venkat.
- Fix for a symbol definition typo in cpufreq_governor.h from Borislav
Petkov.
* tag 'pm+acpi-3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / BGRT: Don't let users configure BGRT on non X86 systems
cpuidle / ACPI: recover percpu ACPI processor cstate
ACPI / I2C: Use parent's ACPI_HANDLE() in acpi_i2c_register_devices()
cpufreq: Correct header guards typo
ACPI / SPI: Use parent's ACPI_HANDLE() in acpi_register_spi_devices()
cpufreq: check OF node /cpus presence before dereferencing it
PM / devfreq: Fix compiler warnings for CONFIG_PM_DEVFREQ unset
PM / QoS: Avoid possible deadlock related to sysfs access
USB / PM: Don't try to hide PM QoS flags from usb_port_device_release()
hayeswang [Sun, 31 Mar 2013 17:02:04 +0000 (17:02 +0000)]
r8169: fix auto speed down issue
It would cause no link after suspending or shutdowning when the
nic changes the speed to 10M and connects to a link partner which
forces the speed to 100M.
Check the link partner ability to determine which speed to set.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Apr 2013 21:39:06 +0000 (17:39 -0400)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into wireless
John W. Linville says:
====================
Here are some more fixes intended for the 3.9 stream...
Regarding the mac80211 bits, Johannes says:
"I had changed the idle handling to simplify it, but broken the
sequencing of commands, at least for ath9k-htc, one patch restores the
sequence. The other patch fixes a crash Jouni found while stress-testing
the remain-on-channel code, when an item is deleted the work struct can
run twice and crash the second time."
As for the iwlwifi bits, Johannes says:
"The only fix here is to the passive-no-RX firmware regulatory
enforcement driver support code to not drop auth frames in quick
succession, leading to not being able to connect to APs on passive
channels in certain circumstances."
Don't forget the NFC bits, about which Samuel says:
"This time we have:
- A crash fix for when a DGRAM LLCP socket is listening while the NFC adapter
is physically removed.
- A potential double skb free when the LLCP socket receive queue is full.
- A fix for properly handling multiple and consecutive LLCP connections, and
not trash the socket ack log.
- A build failure for the MEI microread physical layer, now that the MEI bus
APIs have been merged into char-misc-next."
On top of that, Stone Piao provides an mwifiex fix to avoid accessing
beyond the end of a buffer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Stancek [Thu, 4 Apr 2013 18:35:10 +0000 (11:35 -0700)]
mm: prevent mmap_cache race in find_vma()
find_vma() can be called by multiple threads with read lock
held on mm->mmap_sem and any of them can update mm->mmap_cache.
Prevent compiler from re-fetching mm->mmap_cache, because other
readers could update it in the meantime:
thread 1 thread 2
|
find_vma() | find_vma()
struct vm_area_struct *vma = NULL; |
vma = mm->mmap_cache; |
if (!(vma && vma->vm_end > addr |
&& vma->vm_start <= addr)) { |
| mm->mmap_cache = vma;
return vma; |
^^ compiler may optimize this |
local variable out and re-read |
mm->mmap_cache |
This issue can be reproduced with gcc-4.8.0-1 on s390x by running
mallocstress testcase from LTP, which triggers:
Merge tag 'upstream-3.9-rc6' of git://git.infradead.org/linux-ubifs
Pull UBIFS fix from Artem Bityutskiy:
"Make the space fixup feature work in the case when the file-system is
first mounted R/O and then remounted R/W."
* tag 'upstream-3.9-rc6' of git://git.infradead.org/linux-ubifs:
UBIFS: make space fixup work in the remount case
* pm-fixes:
cpufreq: Correct header guards typo
cpufreq: check OF node /cpus presence before dereferencing it
PM / devfreq: Fix compiler warnings for CONFIG_PM_DEVFREQ unset
PM / QoS: Avoid possible deadlock related to sysfs access
USB / PM: Don't try to hide PM QoS flags from usb_port_device_release()
* acpi-fixes:
ACPI / BGRT: Don't let users configure BGRT on non X86 systems
cpuidle / ACPI: recover percpu ACPI processor cstate
ACPI / I2C: Use parent's ACPI_HANDLE() in acpi_i2c_register_devices()
ACPI / SPI: Use parent's ACPI_HANDLE() in acpi_register_spi_devices()
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- Workaround for device ID conflict between Masterkit MA901 usb radio
device and Atmel V-USB devices, to avoid regressions from older
kernels, by Alexey Klimov
- fix for possible race during input device registration in magicmouse
driver, by Benjamin Tissoires
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: magicmouse: fix race between input_register() and probe()
media: radio-ma901: return ENODEV in probe if usb_device doesn't match
HID: fix Masterkit MA901 hid quirks
Merge tag 'gpio-fixes-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two GPIO fixes for the v3.9 series:
- Fix erroneous return value in the ICH driver
- Make the STMPE driver proper properly on device tree boots"
* tag 'gpio-fixes-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: stmpe: pass DT node to irqdomain
gpio-ich: Fix value returned by ichx_gpio_request
The commit [6ab317419c: ALSA: hda - Allow power_save_controller option
override DCAPS] changed the behavior of power_save_controller so that
it can override the driver capability. This assumed that this option
is rarely changed dynamically unlike power_save option. Too naive.
It turned out that the user-space power-management tool tries to set
power_save_controller option to 1 together with power_save option
without knowing what's actually doing. This enabled forcibly the
runtime PM of the controller, which is known to be broken om many
chips thus disabled as default.
So, the only sane fix is to revert this commit again. It was intended
to ease debugging/testing for runtime PM enablement, but obviously we
need another way for it.
GFS2: Fix unlock of fcntl locks during withdrawn state
When withdraw occurs, we need to continue to allow unlocks of fcntl
locks to occur, however these will only be local, since the node has
withdrawn from the cluster. This prevents triggering a VFS level
bug trap due to locks remaining when a file is closed.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
HID: magicmouse: fix race between input_register() and probe()
Since kernel 3.7, it appears that the input registration occured before
the end of magicmouse_setup_input(). This is shown by receiving a lot of
"EV_SYN SYN_REPORT 1" instead of normal "EV_SYN SYN_REPORT 0".
This value means that the output buffer is full, and the user space
is loosing events.
Using .input_configured guarantees that the race is not occuring, and that
the call of "input_set_events_per_packet(input, 60)" is taken into account
by input_register().
* Added the device ID to the modalias list and assinged ALC662 patches
for it
* Added 4 port support for the device ID 0671 in alc662_parse_auto_config
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"Another round of ARM fixes, which include:
- Fixing a problem with LPAE mapping sections
- Reporting of some hwcaps on Krait CPUs
- Avoiding repetitive warnings in the breakpoint code
- Fixing a build error noticed on Dove platforms with PJ4 CPUs
- Fix masking of level 2 cache revision.
- Fixing timer-based udelay()
- A larger fix for an erratum causing people major grief with Cortex
A15 CPUs"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7690/1: mm: fix CONFIG_LPAE typos
ARM: 7689/1: add unwind annotations to ftrace asm
ARM: 7685/1: delay: use private ticks_per_jiffy field for timer-based delay ops
ARM: 7684/1: errata: Workaround for Cortex-A15 erratum 798181 (TLBI/DSB operations)
ARM: 7682/1: cache-l2x0: fix masking of RTL revision numbering and set_debug init
ARM: iWMMXt: always enable iWMMXt support with PJ4 CPUs
ARM: 7681/1: hw_breakpoint: use warn_once to avoid spam from reset_ctrl_regs()
ARM: 7678/1: Work around faulty ISAR0 register in some Krait CPUs
ARM: 7680/1: Detect support for SDIV/UDIV from ISAR0 register
ARM: 7679/1: Clear IDIVT hwcap if CONFIG_ARM_THUMB=n
ARM: 7677/1: LPAE: Fix mapping in alloc_init_section for unaligned addresses
ARM: KVM: vgic: take distributor lock on sync_hwstate path
ARM: KVM: vgic: force EOIed LRs to the empty state
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Unfortunately, we introduced some big-endian bugs during the last
merge window. Fortunately, Cai and Christian noticed before 3.9
shipped."
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix big-endian bugs which could cause fs corruptions
Zheng Liu [Wed, 3 Apr 2013 16:27:18 +0000 (12:27 -0400)]
ext4: fix big-endian bugs which could cause fs corruptions
When an extent was zeroed out, we forgot to do convert from cpu to le16.
It could make us hit a BUG_ON when we try to write dirty pages out. So
fix it.
[ Also fix a bug found by Dmitry Monakhov where we were missing
le32_to_cpu() calls in the new indirect punch hole code.
There are a number of other big endian warnings found by static code
analyzers, but we'll wait for the next merge window to fix them all
up. These fixes are designed to be Obviously Correct by code
inspection, and easy to demonstrate that it won't make any
difference (and hence, won't introduce any bugs) on little endian
architectures such as x86. --tytso ]
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Reported-by: CAI Qian <caiqian@redhat.com> Reported-by: Christian Kujau <lists@nerdbynature.de> Cc: Dmitry Monakhov <dmonakhov@openvz.org>
Paul Bolle [Wed, 3 Apr 2013 11:24:45 +0000 (12:24 +0100)]
ARM: 7690/1: mm: fix CONFIG_LPAE typos
CONFIG_LPAE doesn't exist: the correct option is CONFIG_ARM_LPAE, so fix
up the two typos under arch/arm/.
The fix to head.S is slightly scary, but this is just for setting up
an early io-mapping for the serial port when running on a big-endian,
LPAE system. Since these systems don't exist in the wild (at least, I
have no access to one outside of kvmtool, which doesn't provide a serial
port suitable for earlyprintk), then we can revisit the code later if it
causes any problems.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rabin Vincent [Tue, 2 Apr 2013 21:11:46 +0000 (22:11 +0100)]
ARM: 7689/1: add unwind annotations to ftrace asm
Add unwind annotations to the ftrace assembly code so that the function
tracer's stacktracing options (func_stack_trace, etc.) work when
CONFIG_ARM_UNWIND is enabled.
Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Thu, 28 Mar 2013 10:17:55 +0000 (11:17 +0100)]
ARM: 7685/1: delay: use private ticks_per_jiffy field for timer-based delay ops
Commit 70264367a243 ("ARM: 7653/2: do not scale loops_per_jiffy when
using a constant delay clock") fixed a problem with our timer-based
delay loop, where loops_per_jiffy is scaled by cpufreq yet used directly
by the timer delay ops.
This patch fixes the problem in a more elegant way by keeping a private
ticks_per_jiffy field in the delay ops, independent of loops_per_jiffy
and therefore not subject to scaling. The loop-based delay continues to
use loops_per_jiffy directly, as it should.
Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Catalin Marinas [Tue, 26 Mar 2013 22:35:04 +0000 (23:35 +0100)]
ARM: 7684/1: errata: Workaround for Cortex-A15 erratum 798181 (TLBI/DSB operations)
On Cortex-A15 (r0p0..r3p2) the TLBI/DSB are not adequately shooting down
all use of the old entries. This patch implements the erratum workaround
which consists of:
1. Dummy TLBIMVAIS and DSB on the CPU doing the TLBI operation.
2. Send IPI to the CPUs that are running the same mm (and ASID) as the
one being invalidated (or all the online CPUs for global pages).
3. CPU receiving the IPI executes a DMB and CLREX (part of the exception
return code already).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rob Herring [Mon, 25 Mar 2013 16:02:48 +0000 (17:02 +0100)]
ARM: 7682/1: cache-l2x0: fix masking of RTL revision numbering and set_debug init
Commit b8db6b8 (ARM: 7547/4: cache-l2x0: add support for Aurora L2 cache
ctrl) moved the masking of the part ID which caused the RTL version to be
lost. Commit 6248d06 (ARM: 7545/1: cache-l2x0: make outer_cache_fns a
field of l2x0_of_data) changed how .set_debug is initialized. Both commits
break commit 74ddcdb (ARM: 7608/1: l2x0: Only set .set_debug
on PL310 r3p0 and earlier) which uses the RTL version to conditionally set
.set_debug function pointer. Commit b8db6b8 also caused the printed cache
ID to be missing the version information.
Fix this by reverting how the part number is masked so the RTL version
info is maintained. The cache-id-part DT property does not set the RTL
bits so masking them should have no effect. Also, re-arrange the order
of the function pointer init so the .set_debug function can be overridden.
Reported-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Yehuda Yitschak <yehuday@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 3 Apr 2013 15:33:26 +0000 (16:33 +0100)]
ARM: iWMMXt: always enable iWMMXt support with PJ4 CPUs
Jason Cooper reports these build errors:
arch/arm/kernel/built-in.o: In function `iwmmxt_do':
/.../arch/arm/kernel/pj4-cp0.c:36: undefined reference to `iwmmxt_task_release'
/.../arch/arm/kernel/pj4-cp0.c:40: undefined reference to `iwmmxt_task_switch'
make: *** [vmlinux] Error 1
This is caused because the PJ4 code explicitly references the iWMMXt
code, but doesn't require it to be built. Fix this by ensuring that
iWMMXt is always enabled with PJ4.
Reported-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Torstein Hegge [Tue, 26 Mar 2013 21:10:05 +0000 (22:10 +0100)]
ALSA: usb: Work around CM6631 sample rate change bug
The C-Media CM6631 USB receiver doesn't respond to changes in sample rate
while the interface is active. The same behavior is observed in other UAC2
hardware like the VIA VT1731.
Reset the interface after setting the sampling frequency on sample rate
changes, to ensure that the sample rate set by snd_usb_init_sample_rate() is
used. Otherwise, the device will try to use the sample rate of the previous
stream, causing distorted sound on sample rate changes.
The reset is performed for all UAC2 devices, as it should not affect a
standards compliant device, but it is only necessary for C-Media CM6631,
VIA VT1731 and possibly others.
Failure to read sample rate from the device is not handled as an error in
set_sample_rate_v2(), as (permanent or intermittent) failure to read sample
rate isn't essential for a successful sample rate set.
Tony Luck [Wed, 3 Apr 2013 11:17:20 +0000 (13:17 +0200)]
ACPI / BGRT: Don't let users configure BGRT on non X86 systems
Fengguang Wu's 0-Day kernel build testing backend found the
following build error for an allmodconfig build on ia64:
drivers/built-in.o: In function `show_yoffset':
>> bgrt.c:(.text+0xe5a71): undefined reference to `bgrt_tab'
>> bgrt.c:(.text+0xe5a91): undefined reference to `bgrt_tab'
drivers/built-in.o: In function `show_xoffset':
>> bgrt.c:(.text+0xe5b51): undefined reference to `bgrt_tab'
>> bgrt.c:(.text+0xe5b71): undefined reference to `bgrt_tab'
drivers/built-in.o: In function `show_type':
>> bgrt.c:(.text+0xe5c31): undefined reference to `bgrt_tab'
drivers/built-in.o:bgrt.c:(.text+0xe5c51): more undefined references to `bgrt_tab' follow
drivers/built-in.o: In function `bgrt_init':
bgrt.c:(.init.text+0x8931): undefined reference to `bgrt_image'
bgrt.c:(.init.text+0x8932): undefined reference to `bgrt_image_size'
bgrt.c:(.init.text+0x8950): undefined reference to `bgrt_image'
bgrt.c:(.init.text+0x8960): undefined reference to `bgrt_image_size'
The problem is that all these undefined names are provided by
arch/x86/platform/efi/efi-bgrt.c - which is obviously not available
to the ia64 build.
It doesn't seem useful to provide the BGRT support for Itanium
(many systems are headless and have no graphics at all). So
just don't let users configure this driver on non-X86 machines.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
netfilter: ip6t_NPT: Fix translation for non-multiple of 32 prefix lengths
The bitmask used for the prefix mangling was being calculated
incorrectly, leading to the wrong part of the address being replaced
when the prefix length wasn't a multiple of 32.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
1) Fix VSOCK layer handling of context ID changes, from Reilly Grant.
2) Now that we have a synchronize_net() in netdev_rx_handler_unregister(),
we can't let any call sites hold locks. Unfortunately bonding does,
so we have to drop the rwlock there a little bit earlier, fix from
Veaceslav Falico.
3) MAC address setting loop exits one iteration too early in mlx4
driver, from Yan Burman.
4) Restore ipv6 routes properly upon ifdown/ifup of loopback, from
Balakumaran Kannan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
VSOCK: Handle changes to the VMCI context ID.
net IPv6 : Fix broken IPv6 routing table after loopback down-up
cbq: incorrect processing of high limits
net/mlx4_en: Fix setting initial MAC address
bonding: get netdev_rx_handler_unregister out of locks
Merge tag 'regmap-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A small collection of fixes. The most important ones are those from
Stephen and Lars-Peter both of which fix cache issues that have been
lurking for a while but not manifesting noticably enough for anyone to
report them."
* tag 'regmap-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: async: Add missing return
regmap: don't corrupt work buffer in _regmap_raw_write()
regmap: cache Fix regcache-rbtree sync
regmap: Initialize `map->debugfs' before regcache
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull DRM fixes from Dave Airlie:
"Two core fixes, both regressions, along with some intel and some
nouveau fixes for regressions and oopses"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: correctly restore mappings if drm_open fails
drm/nouveau: fix NULL ptr dereference from nv50_disp_intr()
drm/nouveau: fix handling empty channel list in ioctl's
drm: don't unlock in the addfb error paths
drm/i915: Fix build failure
drm/i915: Be sure to turn hsync/vsync back on at crt enable (v2)
drm/i915: duct-tape locking when eDP init fails
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A collection of fixes pretty much across the MIPS code. Even the
change to include/linux/signal.h by David Howells' 2a1486981c13 ("Fix
breakage in MIPS siginfo handling") should be considered MIPS-specific
as it touches an ifdefed segment that is only relevant to MIPS and
which unfortunately can't be made to go away entirely."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
Fix breakage in MIPS siginfo handling
Revert "MIPS: BCM63XX: Call board_register_device from device_initcall()"
MIPS: BCM63XX: Make nvram checksum failure non fatal
MIPS: Fix code generation for non-DSP capable CPUs
MIPS: Fix inconsistent formatting inside /proc/cpuinfo
MIPS: SEAD3: Enable LL/SC.
MIPS: Get rid of CONFIG_CPU_HAS_LLSC again
MIPS: Add dependencies for HAVE_ARCH_TRANSPARENT_HUGEPAGE
MIPS: VR4133: Fix probe for LL/SC.
MIPS: Fix logic errors in bitops.c
MIPS: Use CONFIG_CPU_MIPSR2 in csum_partial.S
MIPS: compat: Return same error ENOSYS as native for invalid operation.
If first drm_open fails, the error-handling path will
incorrectly restore inode's mapping to NULL. This can
cause the crash later on. Fix by separately storing
away mapping pointers that drm_open can touch and
restore each from its own respective variable if the
call fails.
Fixes: https://bugzilla.novell.com/show_bug.cgi?id=807850
(thanks to Michal Hocko for investigating investigating and
finding the root cause of the bug)
Dave Airlie [Tue, 2 Apr 2013 20:41:15 +0000 (06:41 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-next
One locking regression fix, and a couple of other i915 ones.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm: don't unlock in the addfb error paths
drm/i915: Fix build failure
drm/i915: Be sure to turn hsync/vsync back on at crt enable (v2)
drm/i915: duct-tape locking when eDP init fails
Reilly Grant [Mon, 1 Apr 2013 18:41:52 +0000 (11:41 -0700)]
VSOCK: Handle changes to the VMCI context ID.
The VMCI context ID of a virtual machine may change at any time. There
is a VMCI event which signals this but datagrams may be processed before
this is handled. It is therefore necessary to be flexible about the
destination context ID of any datagrams received. (It can be assumed to
be correct because it is provided by the hypervisor.) The context ID on
existing sockets should be updated to reflect how the hypervisor is
currently referring to the system.
Signed-off-by: Reilly Grant <grantr@vmware.com> Acked-by: Andy King <acking@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net IPv6 : Fix broken IPv6 routing table after loopback down-up
IPv6 Routing table becomes broken once we do ifdown, ifup of the loopback(lo)
interface. After down-up, routes of other interface's IPv6 addresses through
'lo' are lost.
IPv6 addresses assigned to all interfaces are routed through 'lo' for internal
communication. Once 'lo' is down, those routing entries are removed from routing
table. But those removed entries are not being re-created properly when 'lo' is
brought up. So IPv6 addresses of other interfaces becomes unreachable from the
same machine. Also this breaks communication with other machines because of
NDISC packet processing failure.
This patch fixes this issue by reading all interface's IPv6 addresses and adding
them to IPv6 routing table while bringing up 'lo'.
==Testing==
Before applying the patch:
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$ sudo ifdown lo
$ sudo ifup lo
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$
After applying the patch:
$ route -A inet6
Kernel IPv6 routing
table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$ sudo ifdown lo
$ sudo ifup lo
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$
Signed-off-by: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com> Signed-off-by: Maruthi Thotad <Maruthi.Thotad@ap.sony.com> Signed-off-by: David S. Miller <davem@davemloft.net>
currently cbq works incorrectly for limits > 10% real link bandwidth,
and practically does not work for limits > 50% real link bandwidth.
Below are results of experiments taken on 1 Gbit link
In shaper | Actual Result
-----------+---------------
100M | 108 Mbps
200M | 244 Mbps
300M | 412 Mbps
500M | 893 Mbps
This happen because of q->now changes incorrectly in cbq_dequeue():
when it is called before real end of packet transmitting,
L2T is greater than real time delay, q_now gets an extra boost
but never compensate it.
To fix this problem we prevent change of q->now until its synchronization
with real time.
Signed-off-by: Vasily Averin <vvs@openvz.org> Reviewed-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipc: set msg back to -EAGAIN if copy wasn't performed
Make sure that msg pointer is set back to error value in case of
MSG_COPY flag is set and desired message to copy wasn't found. This
garantees that msg is either a error pointer or a copy address.
Otherwise the last message in queue will be freed without unlinking from
the queue (which leads to memory corruption) and the dummy allocated
copy won't be released.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yan Burman [Tue, 2 Apr 2013 13:49:45 +0000 (16:49 +0300)]
net/mlx4_en: Fix setting initial MAC address
Commit 6bbb6d9 "net/mlx4_en: Optimize Rx fast path filter checks" introduced a regression
under which the MAC address read from the card was not converted correctly
(the most significant byte was not handled), fix that.
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Yan Burman <yanb@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bonding: get netdev_rx_handler_unregister out of locks
Now that netdev_rx_handler_unregister contains synchronize_net(), we need
to call it outside of bond->lock, cause it might sleep. Also, remove the
already unneded synchronize_net().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"After a quiet set of fixes for 3.9-rc4, a lot of people woke up and
sent urgent fixes for 3.9. I pushed back on a number of them that got
deferred to 3.10, but these are the ones that seemed important.
Regression in 3.9:
- Multiple regressions in OMAP2+ clock cleanup
- SH-Mobile frame buffer bug fix that merged here because of
maintainer MIA
- ux500 prcmu changes broke DT booting
- MMCI duplicated regulator setup on ux500
- New ux500 clock driver broke ethernet on snowball
- Local interrupt driver for mvebu broke ethernet
- MVEBU GPIO driver did not get set up right on Orion DT
- incorrect interrupt number on Orion crypto for DT
Long-standing bugs, including candidates for stable:
- Kirkwood MMC needs to disable invalid card detect pins
- MV SDIO pinmux was wrong on Mirabox
- GoFlex Net board file needs to set NAND chip delay
- MSM timer restart race
- ep93xx early debug code broke in 3.7
- i.MX CPU hotplug race
- Incorrect clock setup for OMAP1 USB
- Workaround for bad clock setup by some old OMAP4 boot loaders
- Static I/O mappings on cns3xxx since 3.2"
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: cns3xxx: fix mapping of private memory region
arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
arm: orion5x: correct IRQ used in dtsi for mv_cesa
arm: orion5x: fix orion5x.dtsi gpio parameters
ARM: Kirkwood: fix unused mvsdio gpio pins
arm: mvebu: Use local interrupt only for the timer 0
ARM: kirkwood: Fix chip-delay for GoFlex Net
ARM: ux500: Enable the clock controlling Ethernet on Snowball
ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
fbdev: sh_mobile_lcdc: fixup B side hsync adjust settings
ARM: OMAP: clocks: Delay clk inits atleast until slab is initialized
ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill
ARM: msm: Stop counting before reprogramming clockevent
ARM: ep93xx: Fix wait for UART FIFO to be empty
ARM: OMAP4: PM: fix PM regression introduced by recent clock cleanup
ARM: OMAP3: hwmod data: keep MIDLEMODE in force-standby for musb
ARM: OMAP4: clock data: lock USB DPLL on boot
ARM: OMAP1: fix USB host on 1710
Merge tag 'v3.9-rc1_cns3xxx_fixes' of git://git.infradead.org/users/cbou/linux-cns3xxx into fixes
From Anton Vorontsov <anton@enomsg.org>:
This tag includes Mac Lin's work to revive CNS3xxx booting:
"Since commit 0536bdf33faf (ARM: move iotable mappings within the vmalloc
region), [...] the pre-defined iotable mappings is not in the vmalloc
region. [...] move the iotable mappings into the vmalloc region, and
merge the MPCore private memory region (containing the SCU, the GIC and
the TWD) as a single region."
Plus there is a small cosmetic fix, also from Mac Lin.
* tag 'v3.9-rc1_cns3xxx_fixes' of git://git.infradead.org/users/cbou/linux-cns3xxx:
ARM: cns3xxx: fix mapping of private memory region
[arnd: dropped the cosmetic fix from the merge as it is not needed for 3.9]
Commit ac3ebafa81af76d6 "ACPI / idle: remove usage of the statedata"
changed the percpu processor cstate to a unified cstate in ACPI idle.
That caused all our NHM boxes to boot hang or panic.
In fact, the ACPI idle is based on the assumption of difference percpu
cstate structures that are necessary for the implementation to work
cprrectly. A unique acpi_processor_cx is not sifficient by far.
This patch is just a quick fix re-introducing the percpu cstates.
If someone really wants to unify the ACPI cstates, please make sure
that the whole software infrastructure is changed and take hardware
as well as many different kinds of BIOS settings into account.
[rjw: Changelog] Reported-by: LKP project <lkp@linux.intel.com> Reported-by: Xie ChanglongX <changlongx.xie@intel.com> Tested-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Alex Shi <alex.shi@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI / I2C: Use parent's ACPI_HANDLE() in acpi_i2c_register_devices()
The ACPI handle of struct i2c_adapter's dev member should not be
set, because this causes that struct i2c_adapter to be associated
with the ACPI device node corresponding to its parent as the
second "physical_device", which is incorrect (this happens during
the registration of struct i2c_adapter). Consequently,
acpi_i2c_register_devices() should use the ACPI handle of the
parent of the struct i2c_adapter it is called for rather than the
struct i2c_adapter's ACPI handle (which should be NULL).
Make that happen and modify the i2c-designware-platdrv driver,
which currently is the only driver for ACPI-enumerated I2C
controller chips, not to set the ACPI handle for the
struct i2c_adapter it creates.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Aaron Lu <aaron.lu@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Wolfram Sang <wsa@the-dreams.de>
Mengdong Lin [Thu, 28 Mar 2013 09:20:22 +0000 (05:20 -0400)]
ALSA: hda - bug fix on return value when getting HDMI ELD info
In function snd_hdmi_get_eld(), the variable 'ret' should be initialized to 0.
Otherwise it will be returned uninitialized as non-zero after ELD info is got
successfully. Thus hdmi_present_sense() will always assume ELD info is invalid
by mistake, and /proc file system cannot show the proper ELD info.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Cc: stable@vger.kernel.org Acked-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Heiko Carstens [Sat, 23 Mar 2013 09:29:01 +0000 (10:29 +0100)]
s390/mm: provide emtpy check_pgt_cache() function
All architectures need to provide a check_pgt_cache() function. The s390 one
got lost somewhere.
So reintroduce it to prevent future compile errors e.g. if Thomas Gleixner's
idle loop rework patches get merged.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Thu, 21 Mar 2013 11:50:39 +0000 (12:50 +0100)]
s390/uaccess: fix page table walk
When translating user space addresses to kernel addresses the follow_table()
function had two bugs:
- PROT_NONE mappings could be read accessed via the kernel mapping. That is
e.g. putting a filename into a user page, then protecting the page with
PROT_NONE and afterwards issuing the "open" syscall with a pointer to
the filename would incorrectly succeed.
- when walking the page tables it used the pgd/pud/pmd/pte primitives which
with dynamic page tables give no indication which real level of page tables
is being walked (region2, region3, segment or page table). So in case of an
exception the translation exception code passed to __handle_fault() is not
necessarily correct.
This is not really an issue since __handle_fault() doesn't evaluate the code.
Only in case of e.g. a SIGBUS this code gets passed to user space. If user
space can do something sane with the value is a different question though.
To fix these issues don't use any Linux primitives. Only walk the page tables
like the hardware would do it, however we leave quite some checks away since
we know that we only have full size page tables and each index is within bounds.
ACPI / SPI: Use parent's ACPI_HANDLE() in acpi_register_spi_devices()
The ACPI handle of struct spi_master's dev member should not be
set, because this causes that struct spi_master to be associated
with the ACPI device node corresponding to its parent as the
second "physical_device", which is incorrect (this happens during
the registration of struct spi_master). Consequently,
acpi_register_spi_devices() should use the ACPI handle of the
parent of the struct spi_master it is called for rather than that
struct spi_master's ACPI handle (which should be NULL).
Make that happen and modify the spi-pxa2xx driver, which currently is
the only driver for ACPI-enumerated SPI controller chips, not to set
the ACPI handle for the struct spi_master it creates.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[rjw: Changelog] Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rajagopal Venkat [Thu, 21 Mar 2013 13:28:25 +0000 (13:28 +0000)]
PM / devfreq: Fix compiler warnings for CONFIG_PM_DEVFREQ unset
Fix compiler warnings generated when devfreq is not enabled
(CONFIG_PM_DEVFREQ is not set).
Signed-off-by: Rajagopal Venkat <rajagopal.venkat@linaro.org> Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM / QoS: Avoid possible deadlock related to sysfs access
Commit b81ea1b (PM / QoS: Fix concurrency issues and memory leaks in
device PM QoS) put calls to pm_qos_sysfs_add_latency(),
pm_qos_sysfs_add_flags(), pm_qos_sysfs_remove_latency(), and
pm_qos_sysfs_remove_flags() under dev_pm_qos_mtx, which was a
mistake, because it may lead to deadlocks in some situations.
For example, if pm_qos_remote_wakeup_store() is run in parallel
with dev_pm_qos_constraints_destroy(), they may deadlock in the
following way:
======================================================
[ INFO: possible circular locking dependency detected ] 3.9.0-rc4-next-20130328-sasha-00014-g91a3267 #319 Tainted: G W
-------------------------------------------------------
trinity-child6/12371 is trying to acquire lock:
(s_active#54){++++.+}, at: [<ffffffff81301631>] sysfs_addrm_finish+0x31/0x60
but task is already holding lock:
(dev_pm_qos_mtx){+.+.+.}, at: [<ffffffff81f07cc3>] dev_pm_qos_constraints_destroy+0x23/0x250
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
To avoid that, remove the calls to functions mentioned above from
under dev_pm_qos_mtx and introduce a separate lock to prevent races
between functions that add or remove device PM QoS sysfs attributes
from happening.
Reported-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
USB / PM: Don't try to hide PM QoS flags from usb_port_device_release()
Remove the call to dev_pm_qos_hide_flags(), added by commit 6e30d7cb
"usb: Add driver/usb/core/(port.c,hub.h) files", from
usb_port_device_release(), because (1) it is completely unnecessary
(the flags have been removed already by the PM core during the
unregistration of the device object) and (2) it triggers a NULL
pointer dereference in sysfs_find_dirent() (dev->kobj.sd is NULL at
this point).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"One reversion, a tiny leak fix, and a cc:stable locking fix, in two
parts"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio: console: add locking around c_ovq operations
virtio: console: rename cvq_lock to c_ivq_lock
hw_random: free rng_buffer at module exit
Revert "virtio_console: Initialize guest_connected=true for rproc_serial"
struct block_device lifecycle is defined by its inode (see fs/block_dev.c) -
block_device allocated first time we access /dev/loopXX and deallocated on
bdev_destroy_inode. When we create the device "losetup /dev/loopXX afile"
we want that block_device stay alive until we destroy the loop device
with "losetup -d".
But because we do not hold /dev/loopXX inode its counter goes 0, and
inode/bdev can be destroyed at any moment. Usually it happens at memory
pressure or when user drops inode cache (like in the test below). When later in
loop_clr_fd() we want to use bdev we have use-after-free error with following
stack:
[ Doing bdgrab/bput in loop_set_fd/loop_clr_fd is safe, because every
time we call loop_set_fd() we check that loop_device->lo_state is
Lo_unbound and set it to Lo_bound If somebody will try to set_fd again
it will get EBUSY. And if we try to loop_clr_fd() on unbound loop
device we'll get ENXIO.
loop_set_fd/loop_clr_fd (and any other loop ioctl) is called under
loop_device->lo_ctl_mutex. ]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull tegra clock driver fix from Mike Turquette:
"Missing base address in Tegra clock driver results in non-operational
PCIe. On some devices this means that Ethernet will go uninitialized
and other devices will fail. This pull request fixes it with a single
patch to pass the proper base address in the Tegra clock driver."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: tegra: Allow PLLE training to succeed
Merge tag 'for-3.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rwlove/fcoe
Pull FCoE fixes from Robert Love:
"Critical patches to fix FCoE VN2VN mode with new interfaces targeting
3.9-rc"
* tag 'for-3.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rwlove/fcoe:
libfcoe: Fix fcoe_sysfs VN2VN mode
libfc, fcoe, bnx2fc: Split fc_disc_init into fc_disc_{init, config}
libfc, fcoe, bnx2fc: Always use fcoe_disc_init for discovery layer initialization
fcoe: Fix deadlock between create and destroy paths
bnx2fc: Make the fcoe_cltr the SCSI host parent
Merge tag 'nfc-fixes-3.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-fixes
Samuel Ortiz <sameo@linux.intel.com> says:
"This is the 2nd batch of NFC fixes for 3.9. This time we have:
- A crash fix for when a DGRAM LLCP socket is listening while the NFC adapter
is physically removed.
- A potential double skb free when the LLCP socket receive queue is full.
- A fix for properly handling multiple and consecutive LLCP connections, and
not trash the socket ack log.
- A build failure for the MEI microread physical layer, now that the MEI bus
APIs have been merged into char-misc-next."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thierry Reding [Thu, 14 Mar 2013 15:27:05 +0000 (16:27 +0100)]
clk: tegra: Allow PLLE training to succeed
Under some circumstances the PLLE needs to be retrained, in which case
access to the PMC registers is required. Fix this by passing a pointer
to the PMC registers instead of NULL when registering the PLLE clock.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
Merge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile fix from Chris Metcalf:
"This change allows newer Tilera boot tools to work correctly with
current (and stable) kernels by using the right filename to get the
initramfs from the Tilera hypervisor filesystem."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: expect new initramfs name from hypervisor file system
1) sadb_msg prepared for IPSEC userspace forgets to initialize the
satype field, fix from Nicolas Dichtel.
2) Fix mac80211 synchronization during station removal, from Johannes
Berg.
3) Fix IPSEC sequence number notifications when they wrap, from Steffen
Klassert.
4) Fix cfg80211 wdev tracing crashes when add_virtual_intf() returns an
error pointer, from Johannes Berg.
5) In mac80211, don't call into the channel context code with the
interface list mutex held. From Johannes Berg.
6) In mac80211, if we don't actually associate, do not restart the STA
timer, otherwise we can crash. From Ben Greear.
7) Missing dma_mapping_error() check in e1000, ixgb, and e1000e. From
Christoph Paasch.
8) Fix sja1000 driver defines to not conflict with SH port, from Marc
Kleine-Budde.
9) Don't call il4965_rs_use_green with a NULL station, from Colin Ian
King.
10) Suspend/Resume in the FEC driver fail because the buffer descriptors
are not initialized at all the moments in which they should. Fix
from Frank Li.
11) cpsw and davinci_emac drivers both use the wrong interface to
restart a stopped TX queue. Use netif_wake_queue not
netif_start_queue, the latter is for initialization/bringup not
active management of the queue. From Mugunthan V N.
12) Fix regression in rate calculations done by
psched_ratecfg_precompute(), missing u64 type promotion. From
Sergey Popovich.
13) Fix length overflow in tg3 VPD parsing, from Kees Cook.
14) AOE driver fails to allocate enough headroom, resulting in crashes.
Fix from Eric Dumazet.
15) RX overflow happens too quickly in sky2 driver because pause packet
thresholds are not programmed correctly. From Mirko Lindner.
16) Bonding driver manages arp_interval and miimon settings incorrectly,
disabling one unintentionally disables both. Fix from Nikolay
Aleksandrov.
17) smsc75xx drivers don't program the RX mac properly for jumbo frames.
Fix from Steve Glendinning.
18) Fix off-by-one in Codel packet scheduler. From Vijay Subramanian.
19) Fix packet corruption in atl1c by disabling MSI support, from Hannes
Frederic Sowa.
20) netdev_rx_handler_unregister() needs a synchronize_net() to fix
crashes in bonding driver unload stress tests. From Eric Dumazet.
21) rxlen field of ks8851 RX packet descriptors not interpreted
correctly (it is 12 bits not 16 bits, so needs to be masked after
shifting the 32-bit value down 16 bits). Fix from Max Nekludov.
22) Fix missed RX/TX enable in sh_eth driver due to mishandling of link
change indications. From Sergei Shtylyov.
23) Fix crashes during spurious ECI interrupts in sh_eth driver, also
from Sergei Shtylyov.
24) dm9000 driver initialization is done wrong for revision B devices
with DSP PHY, from Joseph CHANG.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
DM9000B: driver initialization upgrade
sh_eth: make 'link' field of 'struct sh_eth_private' *int*
sh_eth: workaround for spurious ECI interrupt
sh_eth: fix handling of no LINK signal
ks8851: Fix interpretation of rxlen field.
net: add a synchronize_net() in netdev_rx_handler_unregister()
MAINTAINERS: Update netxen_nic maintainers list
atl1e: drop pci-msi support because of packet corruption
net: fq_codel: Fix off-by-one error
net: calxedaxgmac: Wake-on-LAN fixes
net: calxedaxgmac: fix rx ring handling when OOM
net: core: Remove redundant call to 'nf_reset' in 'dev_forward_skb'
smsc75xx: fix jumbo frame support
net: fix the use of this_cpu_ptr
bonding: fix disabling of arp_interval and miimon
ipv6: don't accept node local multicast traffic from the wire
sky2: Threshold for Pause Packet is set wrong
sky2: Receive Overflows not counted
aoe: reserve enough headroom on skbs
line up comment for ndo_bridge_getlink
...
projects / karo-tx-linux.git / log