Willem de Bruijn [Wed, 11 Mar 2015 19:43:55 +0000 (15:43 -0400)]
sock: fix possible NULL sk dereference in __skb_tstamp_tx
Test that sk != NULL before reading sk->sk_tsflags.
Fixes: 49ca0d8bfaf3 ("net-timestamp: no-payload option") Reported-by: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 12 Mar 2015 01:42:02 +0000 (18:42 -0700)]
xps: must clear sender_cpu before forwarding
John reported that my previous commit added a regression
on his router.
This is because sender_cpu & napi_id share a common location,
so get_xps_queue() can see garbage and perform an out of bound access.
We need to make sure sender_cpu is cleared before doing the transmit,
otherwise any NIC busy poll enabled (skb_mark_napi_id()) can trigger
this bug.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: John <jw@nuclearfallout.net> Bisected-by: John <jw@nuclearfallout.net> Fixes: 2bd82484bb4c ("xps: fix xps for stacked devices") Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the notify outside of the spin locks means it can be delayed a
long time (if the dealloc thread is descheduled or there is an
interrupt or softirq).
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Zoltan Kiss <zoltan.kiss@linaro.org> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Wed, 11 Mar 2015 11:29:17 +0000 (14:29 +0300)]
net: sysctl_net_core: check SNDBUF and RCVBUF for min length
sysctl has sysctl.net.core.rmem_*/wmem_* parameters which can be
set to incorrect values. Given that 'struct sk_buff' allocates from
rcvbuf, incorrectly set buffer length could result to memory
allocation failures. For example, set them as follows:
Moreover, the possible minimum is 1, so we can get another kernel panic:
...
BUG: unable to handle kernel paging request at ffff88013caee5c0
IP: [<ffffffff815604cf>] __alloc_skb+0x12f/0x1f0
...
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Tue, 10 Mar 2015 21:17:04 +0000 (17:17 -0400)]
tcp: restore 1.5x per RTT limit to CUBIC cwnd growth in congestion avoidance
Commit 814d488c6126 ("tcp: fix the timid additive increase on stretch
ACKs") fixed a bug where tcp_cong_avoid_ai() would either credit a
connection with an increase of snd_cwnd_cnt, or increase snd_cwnd, but
not both, resulting in cwnd increasing by 1 packet on at most every
alternate invocation of tcp_cong_avoid_ai().
Although the commit correctly implemented the CUBIC algorithm, which
can increase cwnd by as much as 1 packet per 1 packet ACKed (2x per
RTT), in practice that could be too aggressive: in tests on network
paths with small buffers, YouTube server retransmission rates nearly
doubled.
This commit restores CUBIC to a maximum cwnd growth rate of 1 packet
per 2 packets ACKed (1.5x per RTT). In YouTube tests this restored
retransmit rates to low levels.
Testing: This patch has been tested in datacenter netperf transfers
and live youtube.com and google.com servers.
Fixes: 9cd981dcf174 ("tcp: fix stretch ACK bugs in CUBIC") Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Tue, 10 Mar 2015 21:17:03 +0000 (17:17 -0400)]
tcp: fix tcp_cong_avoid_ai() credit accumulation bug with decreases in w
The recent change to tcp_cong_avoid_ai() to handle stretch ACKs
introduced a bug where snd_cwnd_cnt could accumulate a very large
value while w was large, and then if w was reduced snd_cwnd could be
incremented by a large delta, leading to a large burst and high packet
loss. This was tickled when CUBIC's bictcp_update() sets "ca->cnt =
100 * cwnd".
This bug crept in while preparing the upstream version of 814d488c6126.
Testing: This patch has been tested in datacenter netperf transfers
and live youtube.com and google.com servers.
Fixes: 814d488c6126 ("tcp: fix the timid additive increase on stretch ACKs") Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 11 Mar 2015 01:58:32 +0000 (21:58 -0400)]
net: Handle unregister properly when netdev namespace change fails.
If rtnl_newlink() fails on it's call to dev_change_net_namespace(), we
have to make use of the ->dellink() method, if present, just like we
do when rtnl_configure_link() fails.
Fixes: 317f4810e45e ("rtnl: allow to create device with IFLA_LINK_NETNSID set") Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Tue, 10 Mar 2015 18:03:46 +0000 (19:03 +0100)]
net: add comment for sock_efree() usage
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 16e47624e76b43db ("cxgb4: Add new scheme to update T4/T5 firmware")
introduced below coccinelle warning.
>> drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:994:2-8: Replace memcpy with
struct assignment
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver support receive VLAN CTAG HW acceleration feature
(NETIF_F_HW_VLAN_CTAG_RX) through software simulation. There calls the
api .skb_copy_to_linear_data_offset() to skip the VLAN tag, but there
have overlap between the two memory data point range. The patch just fix
the issue.
V2:
Michael Grzeschik suggest to use memmove() instead of skb_copy_to_linear_data_offset().
Reported-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Fixes: 1b7bde6d659d ("net: fec: implement rx_copybreak to improve rx performance") Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
So ->ht is supposed to be the last field of this struct, however
this is broken, since an rcu head is appended after it.
Fixes: 1ce87720d456 ("net: sched: make cls_u32 lockless") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 10 Mar 2015 01:59:50 +0000 (18:59 -0700)]
Merge git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm/s390 bugfixes from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: non-LPAR case obsolete during facilities mask init
KVM: s390: include guest facilities in kvm facility test
KVM: s390: fix in memory copy of facility lists
KVM: s390/cpacf: Fix kernel bug under z/VM
KVM: s390/cpacf: Enable key wrapping by default
Linus Torvalds [Tue, 10 Mar 2015 01:55:52 +0000 (18:55 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"One performance optimization for page_clear and a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: fix incorrect ASCE after crst_table_downgrade
s390/ftrace: fix crashes when switching tracers / add notrace to cpu_relax()
s390/pci: unify pci_iomap symbol exports
s390/pci: fix [un]map_resources sequence
s390: let the compiler do page clearing
s390/pci: fix possible information leak in mmio syscall
s390/dcss: array index 'i' is used before limits check.
s390/scm_block: fix off by one during cluster reservation
s390/jump label: improve and fix sanity check
s390/jump label: add missing jump_label_apply_nops() call
Linus Torvalds [Tue, 10 Mar 2015 01:44:06 +0000 (18:44 -0700)]
Merge tag 'trace-fixes-v4.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull seq-buf/ftrace fixes from Steven Rostedt:
"This includes fixes for seq_buf_bprintf() truncation issue. It also
contains fixes to ftrace when /proc/sys/kernel/ftrace_enabled and
function tracing are started. Doing the following causes some issues:
As well as with function tracing too. Pratyush Anand first reported
this issue to me and supplied a patch. When I tested this on my x86
test box, it caused thousands of backtraces and warnings to appear in
dmesg, which also caused a denial of service (a warning for every
function that was listed). I applied Pratyush's patch but it did not
fix the issue for me. I looked into it and found a slight problem
with trampoline accounting. I fixed it and sent Pratyush a patch, but
he said that it did not fix the issue for him.
I later learned tha Pratyush was using an ARM64 server, and when I
tested on my ARM board, I was able to reproduce the same issue as
Pratyush. After applying his patch, it fixed the problem. The above
test uncovered two different bugs, one in x86 and one in ARM and
ARM64. As this looked like it would affect PowerPC, I tested it on my
PPC64 box. It too broke, but neither the patch that fixed ARM or x86
fixed this box (the changes were all in generic code!). The above
test, uncovered two more bugs that affected PowerPC. Again, the
changes were only done to generic code. It's the way the arch code
expected things to be done that was different between the archs. Some
where more sensitive than others.
The rest of this series fixes the PPC bugs as well"
* tag 'trace-fixes-v4.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix ftrace enable ordering of sysctl ftrace_enabled
ftrace: Fix en(dis)able graph caller when en(dis)abling record via sysctl
ftrace: Clear REGS_EN and TRAMP_EN flags on disabling record via sysctl
seq_buf: Fix seq_buf_bprintf() truncation
seq_buf: Fix seq_buf_vprintf() truncation
1) nft_compat accidently truncates ethernet protocol to 8-bits, from
Arturo Borrero.
2) Memory leak in ip_vs_proc_conn(), from Julian Anastasov.
3) Don't allow the space required for nftables rules to exceed the
maximum value representable in the dlen field. From Patrick
McHardy.
4) bcm63xx_enet can accidently leave interrupts permanently disabled
due to errors in the NAPI polling exit logic. Fix from Nicolas
Schichan.
5) Fix OOPSes triggerable by the ping protocol module, due to missing
address family validations etc. From Lorenzo Colitti.
6) Don't use RCU locking in sleepable context in team driver, from Jiri
Pirko.
7) xen-netback miscalculates statistic offset pointers when reporting
the stats to userspace. From David Vrabel.
8) Fix a leak of up to 256 pages per VIF destroy in xen-netaback, also
from David Vrabel.
9) ip_check_defrag() cannot assume that skb_network_offset(),
particularly when it is used by the AF_PACKET fanout defrag code.
From Alexander Drozdov.
10) gianfar driver doesn't query OF node names properly when trying to
determine the number of hw queues available. Fix it to explicitly
check for OF nodes named queue-group. From Tobias Waldekranz.
11) MID field in macb driver should be 12 bits, not 16. From Punnaiah
Choudary Kalluri.
12) Fix unintentional regression in traceroute due to timestamp socket
option changes. Empty ICMP payloads should be allowed in
non-timestamp cases. From Willem de Bruijn.
13) When devices are unregistered, we have to get rid of AF_PACKET
multicast list entries that point to it via ifindex. Fix from
Francesco Ruggeri.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tipc: fix bug in link failover handling
net: delete stale packet_mclist entries
net: macb: constify macb configuration data
MAINTAINERS: add Marc Kleine-Budde as co maintainer for CAN networking layer
MAINTAINERS: linux-can moved to github
can: kvaser_usb: Read all messages in a bulk-in URB buffer
can: kvaser_usb: Avoid double free on URB submission failures
can: peak_usb: fix missing ctrlmode_ init for every dev
can: add missing initialisations in CAN related skbuffs
ip: fix error queue empty skb handling
bgmac: Clean warning messages
tcp: align tcp_xmit_size_goal() on tcp_tso_autosize()
net: fec: fix unbalanced clk disable on driver unbind
net: macb: Correct the MID field length value
net: gianfar: correctly determine the number of queue groups
ipv4: ip_check_defrag should not assume that skb_network_offset is zero
net: bcmgenet: properly disable password matching
net: eth: xgene: fix booting with devicetree
bnx2x: Force fundamental reset for EEH recovery
xen-netback: refactor xenvif_handle_frag_list()
...
Linus Torvalds [Tue, 10 Mar 2015 01:00:25 +0000 (18:00 -0700)]
Merge tag 'regulator-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of driver specific fixes plus a fix for a regression in the
core where the updates to use sysfs group registration were overly
enthusiastic in eliding properties and removed some that had been
previously present"
* tag 'regulator-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix regression due to NULL constraints check
regulator: rk808: Set the enable time for LDOs
regulator: da9210: Mask all interrupt sources to deassert interrupt line
Linus Torvalds [Tue, 10 Mar 2015 00:50:02 +0000 (17:50 -0700)]
Merge tag 'spi-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of driver specific fixes to which the usual comments
about them being important if you see them mostly apply (except for
the comment fix). The pl022 one is particularly nasty for anyone
affected by it"
* tag 'spi-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pl022: Fix race in giveback() leading to driver lock-up
spi: dw-mid: avoid potential NULL dereference
spi: img-spfi: Verify max spfi transfer length
spi: fix a typo in comment.
spi: atmel: Fix interrupt setup for PDC transfers
spi: dw: revisit FIFO size detection again
spi: dw-pci: correct number of chip selects
drivers: spi: ti-qspi: wait for busy bit clear before data write/read
Linus Torvalds [Tue, 10 Mar 2015 00:45:34 +0000 (17:45 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull tpm fixes from James Morris:
"fixes for the TPM driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: fix call order in tpm-chip.c
tpm/ibmvtpm: Additional LE support for tpm_ibmvtpm_send
Linus Torvalds [Tue, 10 Mar 2015 00:35:29 +0000 (17:35 -0700)]
Merge tag 'fbdev-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- Fix regression in with omapdss when using i2c displays
- Fix possible null deref in fbmon
- Check kalloc return value in AMBA CLCD
* tag 'fbdev-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
OMAPDSS: fix regression with display sysfs files
video: fbdev: fix possible null dereference
video: ARM CLCD: Add missing error check for devm_kzalloc
Linus Torvalds [Tue, 10 Mar 2015 00:30:09 +0000 (17:30 -0700)]
Merge branch 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"The cgroup iteration update two years ago and the recent cpuset
restructuring introduced regressions in subset of cpuset
configurations. Three patches to fix them.
All are marked for -stable"
* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: Fix cpuset sched_relax_domain_level
cpuset: fix a warning when clearing configured masks in old hierarchy
cpuset: initialize effective masks when clone_children is enabled
Linus Torvalds [Tue, 10 Mar 2015 00:00:54 +0000 (17:00 -0700)]
Merge branch 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
"One fix patch for a subtle livelock condition which can happen on
PREEMPT_NONE kernels involving two racing cancel_work calls. Whoever
comes in the second has to wait for the previous one to finish. This
was implemented by making the later one block for the same condition
that the former would be (work item completion) and then loop and
retest; unfortunately, depending on the wake up order, the later one
could lock out the former one to finish by busy looping on the cpu.
This is fixed by implementing explicit wait mechanism. Work item
might not belong anywhere at this point and there's remote possibility
of thundering herd problem. I originally tried to use bit_waitqueue
but it didn't work for static work items on modules. It's currently
using single wait queue with filtering wake up function and exclusive
wakeup. If this ever becomes a problem, which is not very likely, we
can try to figure out a way to piggy back on bit_waitqueue"
* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix hang involving racing cancel[_delayed]_work_sync()'s for PREEMPT_NONE
Jon Paul Maloy [Mon, 9 Mar 2015 20:16:22 +0000 (16:16 -0400)]
tipc: fix bug in link failover handling
In commit c637c1035534867b85b78b453c38c495b58e2c5a
("tipc: resolve race problem at unicast message reception") we
introduced a new mechanism for delivering buffers upwards from link
to socket layer.
That code contains a bug in how we handle the new link input queue
during failover. When a link is reset, some of its users may be blocked
because of congestion, and in order to resolve this, we add any pending
wakeup pseudo messages to the link's input queue, and deliver them to
the socket. This misses the case where the other, remaining link also
may have congested users. Currently, the owner node's reference to the
remaining link's input queue is unconditionally overwritten by the
reset link's input queue. This has the effect that wakeup events from
the remaining link may be unduely delayed (but not lost) for a
potentially long period.
We fix this by adding the pending events from the reset link to the
input queue that is currently referenced by the node, whichever one
it is.
This commit should be applied to both net and net-next.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is deleted from a net namespace the ifindex in the
corresponding entries in PF_PACKET sockets' mclists becomes stale.
This can create inconsistencies if later an interface with the same ifindex
is moved from a different namespace (not that unlikely since ifindexes are
per-namespace).
In particular we saw problems with dev->promiscuity, resulting
in "promiscuity touches roof, set promiscuity failed. promiscuity
feature of device might be broken" warnings and EOVERFLOW failures of
setsockopt(PACKET_ADD_MEMBERSHIP).
This patch deletes the mclist entries for interfaces that are deleted.
Since this now causes setsockopt(PACKET_DROP_MEMBERSHIP) to fail with
EADDRNOTAVAIL if called after the interface is deleted, also make
packet_mc_drop not fail.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Mar 2015 19:41:00 +0000 (15:41 -0400)]
Merge tag 'linux-can-fixes-for-4.0-20150309' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-03-09
this is a pull request for net/master for the 4.0 release cycle, it consists of
6 patches:
A patch by Oliver Hartkopp fixes a long outstanding bug in the infrastructure,
which leads to skb_under_panics when CAN interfaces are used by AF_PACKET
sockets e.g. by dhclient. Stephane Grosjean contributes a patch for the
peak_usb driver which adds a missing initialization. Two patches by Ahmed S.
Darwish fix problems in the kvaser_usb driver. Followed by two patches by
myself, updating the MAINTAINERS file
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ftrace: Fix ftrace enable ordering of sysctl ftrace_enabled
Some archs (specifically PowerPC), are sensitive with the ordering of
the enabling of the calls to function tracing and setting of the
function to use to be traced.
That is, update_ftrace_function() sets what function the ftrace_caller
trampoline should call. Some archs require this to be set before
calling ftrace_run_update_code().
Another bug was discovered, that ftrace_startup_sysctl() called
ftrace_run_update_code() directly. If the function the ftrace_caller
trampoline changes, then it will not be updated. Instead a call
to ftrace_startup_enable() should be called because it tests to see
if the callback changed since the code was disabled, and will
tell the arch to update appropriately. Most archs do not need this
notification, but PowerPC does.
The problem could be seen by the following commands:
Pratyush Anand [Fri, 6 Mar 2015 18:28:06 +0000 (23:58 +0530)]
ftrace: Fix en(dis)able graph caller when en(dis)abling record via sysctl
When ftrace is enabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_START_FUNC_RET command to ftrace_run_update_code(). Similarly, when
ftrace is disabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_STOP_FUNC_RET command to ftrace_run_update_code().
Since ftrace_enabled = 0, ftrace_enable_ftrace_graph_caller() is never
called.
# echo 1 > /proc/sys/kernel/ftrace_enabled
Now ftrace_enabled will be set to true, but still
ftrace_enable_ftrace_graph_caller() will not be called, which is not
desired.
Further if we execute the following after this:
# echo nop > /sys/kernel/debug/tracing/current_tracer
Now since ftrace_enabled is set it will call
ftrace_disable_ftrace_graph_caller(), which causes a kernel warning on
the ARM platform.
On the ARM platform, when ftrace_enable_ftrace_graph_caller() is called,
it checks whether the old instruction is a nop or not. If it's not a nop,
then it returns an error. If it is a nop then it replaces instruction at
that address with a branch to ftrace_graph_caller.
ftrace_disable_ftrace_graph_caller() behaves just the opposite. Therefore,
if generic ftrace code ever calls either ftrace_enable_ftrace_graph_caller()
or ftrace_disable_ftrace_graph_caller() consecutively two times in a row,
then it will return an error, which will cause the generic ftrace code to
raise a warning.
Note, x86 does not have an issue with this because the architecture
specific code for ftrace_enable_ftrace_graph_caller() and
ftrace_disable_ftrace_graph_caller() does not check the previous state,
and calling either of these functions twice in a row has no ill effect.
ftrace: Clear REGS_EN and TRAMP_EN flags on disabling record via sysctl
When /proc/sys/kernel/ftrace_enabled is set to zero, all function
tracing is disabled. But the records that represent the functions
still hold information about the ftrace_ops that are hooked to them.
ftrace_ops may request "REGS" (have a full set of pt_regs passed to
the callback), or "TRAMP" (the ops has its own trampoline to use).
When the record is updated to represent the state of the ops hooked
to it, it sets "REGS_EN" and/or "TRAMP_EN" to state that the callback
points to the correct trampoline (REGS has its own trampoline).
When ftrace_enabled is set to zero, all ftrace locations are a nop,
so they do not point to any trampoline. But the _EN flags are still
set. This can cause the accounting to go wrong when ftrace_enabled
is cleared and an ops that has a trampoline is registered or unregistered.
For example, the following will cause ftrace to crash:
As function_graph uses a trampoline, when ftrace_enabled is set to zero
the updates to the record are not done. When enabling function_graph
again, the record will still have the TRAMP_EN flag set, and it will
look for an op that has a trampoline other than the function_graph
ops, and fail to find one.
Ahmed S. Darwish [Thu, 26 Feb 2015 15:22:02 +0000 (10:22 -0500)]
can: kvaser_usb: Read all messages in a bulk-in URB buffer
The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.
The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.
Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ahmed S. Darwish [Thu, 26 Feb 2015 15:20:11 +0000 (10:20 -0500)]
can: kvaser_usb: Avoid double free on URB submission failures
Upon a URB submission failure, the driver calls usb_free_urb()
but then manually frees the URB buffer by itself. Meanwhile
usb_free_urb() has alredy freed out that transfer buffer since
we're the only code path holding a reference to this URB.
Remove two of such invalid manual free().
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can: peak_usb: fix missing ctrlmode_ init for every dev
Fixes a missing initialization of ctrlmode and ctrlmode_supported fields,
for all other CAN devices than the first one. This fix only concerns
the PCAN-USB Pro FD dual-channels CAN-FD device made by PEAK-System.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When reading from the error queue, msg_name and msg_control are only
populated for some errors. A new exception for empty timestamp skbs
added a false positive on icmp errors without payload.
`traceroute -M udpconn` only displayed gateways that return payload
with the icmp error: the embedded network headers are pulled before
sock_queue_err_skb, leaving an skb with skb->len == 0 otherwise.
Fix this regression by refining when msg_name and msg_control
branches are taken. The solutions for the two fields are independent.
msg_name only makes sense for errors that configure serr->port and
serr->addr_offset. Test the first instead of skb->len. This also fixes
another issue. saddr could hold the wrong data, as serr->addr_offset
is not initialized in some code paths, pointing to the start of the
network header. It is only valid when serr->port is set (non-zero).
msg_control support differs between IPv4 and IPv6. IPv4 only honors
requests for ICMP and timestamps with SOF_TIMESTAMPING_OPT_CMSG. The
skb->len test can simply be removed, because skb->dev is also tested
and never true for empty skbs. IPv6 honors requests for all errors
aside from local errors and timestamps on empty skbs.
In both cases, make the policy more explicit by moving this logic to
a new function that decides whether to process msg_control and that
optionally prepares the necessary fields in skb->cb[]. After this
change, the IPv4 and IPv6 paths are more similar.
The last case is rxrpc. Here, simply refine to only match timestamps.
Fixes: 49ca0d8bfaf3 ("net-timestamp: no-payload option") Reported-by: Jan Niehusmann <jan@gondor.com> Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes
v1->v2
- fix local origin test inversion in ip6_datagram_support_cmsg
- make v4 and v6 code paths more similar by introducing analogous
ipv4_datagram_support_cmsg
- fix compile bug in rxrpc Signed-off-by: David S. Miller <davem@davemloft.net>
On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Acked-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 8 Mar 2015 19:47:18 +0000 (12:47 -0700)]
Merge tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here's a round of USB fixes for 4.0-rc3.
Nothing major, the usual gadget, xhci and usb-serial fixes and a few
new device ids as well.
All have been in linux-next successfully"
* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
xhci: Workaround for PME stuck issues in Intel xhci
xhci: fix reporting of 0-sized URBs in control endpoint
usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
USB: ch341: set tty baud speed according to tty struct
USB: serial: cp210x: Adding Seletek device id's
USB: pl2303: disable break on shutdown
USB: mxuport: fix null deref when used as a console
USB: serial: clean up bus probe error handling
USB: serial: fix port attribute-creation race
USB: serial: fix tty-device error handling at probe
USB: serial: fix potential use-after-free after failed probe
USB: console: add dummy __module_get
USB: ftdi_sio: add PIDs for Actisense USB devices
Revert "USB: serial: make bulk_out_size a lower limit"
cdc-acm: Add support for Denso cradle CU-321
usb-storage: support for more than 8 LUNs
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
USB: usbfs: don't leak kernel data in siginfo
xhci: Clear the host side toggle manually when endpoint is 'soft reset'
xhci: Allocate correct amount of scratchpad buffers
...
Linus Torvalds [Sun, 8 Mar 2015 19:25:40 +0000 (12:25 -0700)]
Merge tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other
serial driver bugfixes as well. Most notable is a wait_until_sent
bugfix that was traced back to being around since before 2.6.12 that
Johan has fixed up.
All have been in linux-next successfully"
* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: fix tty_wait_until_sent maximum timeout
TTY: fix tty_wait_until_sent on 64-bit machines
USB: serial: fix infinite wait_until_sent timeout
TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
net: irda: fix wait_until_sent poll timeout
serial: uapi: Declare all userspace-visible io types
serial: core: Fix iotype userspace breakage
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
console: Fix console name size mismatch
tty: fix up atime/mtime mess, take four
serial: 8250_dw: Fix get_mctrl behaviour
serial:8250:8250_pci: delete unneeded quirk entries
serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
Change email address for 8250_pci
serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
Revert "tty/serial: of_serial: add DT alias ID handling"
Linus Torvalds [Sun, 8 Mar 2015 19:15:47 +0000 (12:15 -0700)]
Merge tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two char/misc fixes for 4.0-rc3.
One is a reported binder driver fix needed due to a change in the mm
core that happened in 4.0-rc1. Another is a mei driver fix that
resolves a reported issue in that driver.
Both have been in linux-next for a while"
* tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: make device disabled on stop unconditionally
android: binder: fix binder mmap failures
Linus Torvalds [Sun, 8 Mar 2015 18:51:04 +0000 (11:51 -0700)]
Merge tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull "code of conflict" from Greg KH:
"This file tries to set the rational basis for our code reviews, gives
some advice on how to conduct them, and provides an excalation channel
for any kernel developers if they so desire it"
[ Let's see how this works ]
* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Code of Conflict
Input: psmouse - disable "palm detection" in the focaltech driver
Apparently, the threshold for large contact area seems to be rather low on
some devices, causing the touchpad to frequently freeze during normal
usage. Because we do now know how we are supposed to use the value in
question, this commit just drops the related code completely.
Input: psmouse - disable changing resolution/rate/scale for FocalTech
These PS/2 commands make some touchpads stop responding, so this commit
adds some dummy functions to replace the generic implementation. Because
scale changes were not encapsulated in a method of struct psmouse yet, this
commit adds a method set_scale to psmouse.
Input: psmouse - ensure that focaltech reports consistent coordinates
We don't know whether x_max or y_max really hold the maximum possible
coordinates, and we don't know for sure whether we correctly interpret the
coordinates sent by the touchpad, so we clamp the reported values to
prevent confusion in userspace code.
Linus Torvalds [Sat, 7 Mar 2015 19:31:17 +0000 (11:31 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"arm64 and generic kernel/module.c (acked by Rusty) fixes for
CONFIG_DEBUG_SET_MODULE_RONX"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
kernel/module.c: Update debug alignment after symtable generation
arm64: Don't use is_module_addr in setting page attributes
Johan Hovold [Wed, 4 Mar 2015 09:39:07 +0000 (10:39 +0100)]
TTY: fix tty_wait_until_sent maximum timeout
Currently tty_wait_until_sent may take up to twice as long as the
requested timeout while waiting for driver and hardware buffers to
drain.
Fix this by taking the remaining number of jiffies after waiting for
driver buffers to drain into account so that the timeout actually
becomes a maximum timeout as it is documented to be.
Note that this specifically implies tighter timings when closing a port
as a consequence of actually honouring the port closing-wait setting
for drivers relying on tty_wait_until_sent_from_close (e.g. via
tty_port_close_start).
Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 4 Mar 2015 09:39:06 +0000 (10:39 +0100)]
TTY: fix tty_wait_until_sent on 64-bit machines
Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an
infinite timeout (0) would be passed to the underlying tty-driver's
wait_until_sent-operation as a negative timeout (-1), causing it to
return immediately.
This manifests itself for example as tcdrain() returning immediately,
drivers not honouring the drain flags when setting terminal attributes,
or even dropped data on close as a requested infinite closing-wait
timeout would be ignored.
The first symptom was reported by Asier LLANO who noted that tcdrain()
returned prematurely when using the ftdi_sio usb-serial driver.
Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the
underlying tty driver.
Note that the serial-core wait_until_sent-implementation is not affected
by this bug due to a lucky chance (comparison to an unsigned maximum
timeout), and neither is the cyclades one that had an explicit check for
negative timeouts, but all other tty drivers appear to be affected.
Remove incorrect and redundant wait_until_sent operation, which waits
for the driver buffer rather than any hardware buffers to drain,
something which is already taken care of by the tty layer (and
chars_in_buffer).
Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 1 Mar 2015 15:24:28 +0000 (10:24 -0500)]
serial: uapi: Declare all userspace-visible io types
ioctl(TIOCGSERIAL|TIOCSSERIAL) report and can change the port->iotype.
UART drivers use the UPIO_* definitions, but the uapi header defines
parallel values and userspace uses these parallel values for ioctls;
thus the userspace values are definitive.
Define UPIO_* iotypes in terms of the uapi defines, SERIAL_IO_*;
extend the uapi defines to include all values in use by the serial
core.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 1 Mar 2015 15:18:16 +0000 (10:18 -0500)]
serial: core: Fix iotype userspace breakage
commit 3ffb1a8193bea ("serial: core: Add big-endian iotype")
re-numbered userspace-dependent values; ioctl(TIOCSSERIAL) can
assign the port iotype (which is expected to match the selected
i/o accessors), so iotype values must not be changed.
Cc: Kevin Cernekee <cernekee@gmail.com> Cc: <stable@vger.kernel.org> # 3.19+ Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Reviewed-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Axel Lin [Mon, 16 Feb 2015 14:39:04 +0000 (22:39 +0800)]
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
Fix return from sprd_handle_irq() with spin_lock held.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 1 Mar 2015 15:11:05 +0000 (10:11 -0500)]
console: Fix console name size mismatch
commit 6ae9200f2cab7 ("enlarge console.name") increased the storage
for the console name to 16 bytes, but not the corresponding
struct console_cmdline::name storage. Console names longer than
8 bytes cause read beyond end-of-string and failure to match
console; I'm not sure if there are other unexpected consequences.
But it still misses one point. As John Paul correctly points out, we
do not care about setting date. If somebody ever changes wall
time backwards (by mistake for example), tty timestamps are never
updated until the original wall time passes.
So check the absolute difference of times and if it large than "8
seconds or so", always update the time. That means we will update
immediatelly when changing time. Ergo, CAP_SYS_TIME can foul the
check, but it was always that way.
Thanks John for serving me this so nicely debugged.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: John Paul Perry <john_paul.perry@alcatel-lucent.com> Cc: <stable@vger.kernel.org> # all, as b0b885657 was backported Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Desmond Liu [Fri, 27 Feb 2015 00:35:57 +0000 (16:35 -0800)]
serial: 8250_dw: Fix get_mctrl behaviour
Fixed behaviour of get_mctrl() serial driver function as documented in:
https://www.kernel.org/doc/Documentation/serial/driver
Added device-tree properties 'dcd-override', 'dsr-override',
'cts-override', and 'ri-override' specific to the Synopsis 8250
DesignWare UART driver. Allows one to force Data Carrier Detect,
Clear To Send, and Data Set Ready signals to permanently be reported as
active. The Ring indicator can be forced to be reported as inactive.
It is possible that if modem control signalling is enabled on a port
that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the
driver can hang indefinitely waiting for the state to change. The new
DT properties allow the driver to ignore the state of these pins on
serial ports that don't support them, as recommended in the kernel
documentation.
Reported-by: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conditional RX-FIFO read seems to cause spurious interrupts and we
see just:
|serial8250: too much work for irq29
The previous behaviour was "default" for decades and Marvell's 88f6282 SoC
might not be the only that relies on it. Therefore the Omap fix is
reverted for now.
Fixes: 0aa525d11859 ("tty: serial: 8250_core: read only RX if there is
something in the FIFO") Reported-By: Nicolas Schichan <nschichan@freebox.fr> Debuged-By: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 7 Mar 2015 00:54:22 +0000 (16:54 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon, imx, msm, and i915 fixes.
The msm, imx and i915 ones are fairly run of the mill.
Radeon had some DP audio and posting reads for irq fixes, along with a
fix for 32-bit kernels with new cards, we were using unsigned long to
represent GPU side memory space, but since that changed size on 32 vs
64 cards with lots of VRAM failed, so the change has no effect on
x86-64, just moves to using uint64_t instead"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (35 commits)
drm/msm: kexec fixes
drm/msm/mdp5: fix cursor blending
drm/msm/mdp5: fix cursor ROI
drm/msm/atomic: Don't leak atomic commit object when commit fails
drm/msm/mdp5: Avoid flushing registers when CRTC is disabled
drm/msm: update generated headers (add 6th lm.base entry)
drm/msm/mdp5: fixup "drm/msm: fix fallout of atomic dpms changes"
drm/ttm: device address space != CPU address space
drm/mm: Support 4 GiB and larger ranges
drm/i915: gen4: work around hang during hibernation
drm/i915: Check for driver readyness before handling an underrun interrupt
drm/radeon: fix interlaced modes on DCE8
drm/radeon: fix DRM_IOCTL_RADEON_CS oops
drm/radeon: do a posting read in cik_set_irq
drm/radeon: do a posting read in si_set_irq
drm/radeon: do a posting read in evergreen_set_irq
drm/radeon: do a posting read in r600_set_irq
drm/radeon: do a posting read in rs600_set_irq
drm/radeon: do a posting read in r100_set_irq
radeon/audio: fix DP audio on DCE6
...
This patch marks baytrail_i2c_acquire() that it might sleep. Also it chages
while-loop to do-while and, though it is matter of taste, gives a chance to
check one more time before report a timeout.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It seems the idea behind the cross-check is to prevent acquire semaphore when
there is no release callback and vice versa. Thus, patch fixes a typo.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Andy Shevchenko [Tue, 10 Feb 2015 17:06:08 +0000 (19:06 +0200)]
i2c: designware-baytrail: fix sparse warnings
There is no need to export functions that are used as the callbacks in the
struct dw_i2c_dev. Otherwise we get the following warnings:
drivers/i2c/busses/i2c-designware-baytrail.c:63:5: warning: symbol 'baytrail_i2c_acquire' was not declared. Should it be static?
drivers/i2c/busses/i2c-designware-baytrail.c:114:6: warning: symbol 'baytrail_i2c_release' was not declared. Should it be static?
While here, do few indentation fixes, remove i2c_dw_eval_lock_support() from
functions exported to the modules and redundant assignment of local sem
variable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Andy Shevchenko [Tue, 10 Feb 2015 17:06:07 +0000 (19:06 +0200)]
i2c: designware-baytrail: fix typo in error path
It seems we have same message for different return values in get_sem() and
baytrail_i2c_acquire(). I suspect this is just a typo, so this patch fixes it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Andy Shevchenko [Tue, 10 Feb 2015 17:06:06 +0000 (19:06 +0200)]
i2c: designware-baytrail: describe magic numbers
The patch converts hardcoded numerical constants to a named ones.
While here, align the variable name in get_sem() and reset_semaphore().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Fri, 6 Mar 2015 21:52:54 +0000 (13:52 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Outside of misc fixes, Filipe has a few fsync corners and we're
pulling in one more of Josef's fixes from production use here"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs:__add_inode_ref: out of bounds memory read when looking for extended ref.
Btrfs: fix data loss in the fast fsync path
Btrfs: remove extra run_delayed_refs in update_cowonly_root
Btrfs: incremental send, don't rename a directory too soon
btrfs: fix lost return value due to variable shadowing
Btrfs: do not ignore errors from btrfs_lookup_xattr in do_setxattr
Btrfs: fix off-by-one logic error in btrfs_realloc_node
Btrfs: add missing inode update when punching hole
Btrfs: abort the transaction if we fail to update the free space cache inode
Btrfs: fix fsync race leading to ordered extent memory leaks
Linus Torvalds [Fri, 6 Mar 2015 21:43:33 +0000 (13:43 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal management fixes from Eduardo Valentin:
"Specifics:
- adding Lukasz as maintainer of samsung thermal driver.
- driver fixes: exynos and int430x.
- one fix in the exynos cpufreq driver related to cpu cooling (acked
by cpufreq maintainer).
- fix default sysfs attributes of cooling devices
Note: I am sending this pull on Rui's behalf while he fixes issues in his Linux box"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: Make sysfs attributes of cooling devices default attributes
Thermal/int340x: Fix memleak for aux trip
MAINTAINERS: Add entry for SAMSUNG THERMAL DRIVER
cpufreq: exynos: Use simple approach to asses if cpu cooling can be used
thermal: exynos: Fix wrong control of power down detection mode for Exynos7
Dave Airlie [Fri, 6 Mar 2015 21:40:17 +0000 (07:40 +1000)]
Merge tag 'drm-intel-fixes-2015-03-05' of git://anongit.freedesktop.org/drm-intel into drm-fixes
two fixes, both cc'd stable.
* tag 'drm-intel-fixes-2015-03-05' of git://anongit.freedesktop.org/drm-intel:
drm/i915: gen4: work around hang during hibernation
drm/i915: Check for driver readyness before handling an underrun interrupt
Jarkko Sakkinen [Sun, 1 Mar 2015 21:55:47 +0000 (23:55 +0200)]
tpm: fix call order in tpm-chip.c
- tpm_dev_add_device(): cdev_add() must be done before uevent is
propagated in order to avoid races.
- tpm_chip_register(): tpm_dev_add_device() must be done as the
last step before exposing device to the user space in order to
avoid races.
In addition clarified description in tpm_chip_register().
Fixes: 313d21eeab92 ("tpm: device class for tpm") Fixes: afb5abc262e9 ("tpm: two-phase chip management functions") Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
tpm/ibmvtpm: Additional LE support for tpm_ibmvtpm_send
Problem: When IMA and VTPM are both enabled in kernel config,
kernel hangs during bootup on LE OS.
Why?: IMA calls tpm_pcr_read() which results in tpm_ibmvtpm_send
and tpm_ibmtpm_recv getting called. A trace showed that
tpm_ibmtpm_recv was hanging.
Resolution: tpm_ibmtpm_recv was hanging because tpm_ibmvtpm_send
was sending CRQ message that probably did not make much sense
to phype because of Endianness. The fix below sends correctly
converted CRQ for LE. This was not caught before because it
seems IMA is not enabled by default in kernel config and
IMA exercises this particular code path in vtpm.
Tested with IMA and VTPM enabled in kernel config and VTPM
enabled on both a BE OS and a LE OS ppc64 lpar. This exercised
CRQ and TPM command code paths in vtpm.
Patch is against Peter's tpmdd tree on github which included
Vicky's previous vtpm le patches.
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> # eb71f8a5e33f: "Added Little Endian support to vtpm module" Cc: <stable@vger.kernel.org> Reviewed-by: Ashley Lai <ashley@ahsleylai.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
spi: pl022: Fix race in giveback() leading to driver lock-up
Commit fd316941c ("spi/pl022: disable port when unused") introduced a race,
which leads to possible driver lock up (easily reproducible on SMP).
The problem happens in giveback() function where the completion of the transfer
is signalled to SPI subsystem and then the HW SPI controller is disabled. Another
transfer might be setup in between, which brings driver in locked-up state.
Lockup! SPI controller is disabled and the data will never be received. Whole
SPI subsystem is waiting for transfer ACK and blocked.
So, only signal transfer completion after disabling the controller.
Fixes: fd316941c (spi/pl022: disable port when unused) Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
Linus Torvalds [Fri, 6 Mar 2015 18:55:41 +0000 (10:55 -0800)]
Merge tag 'sound-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few more ASoC changes that have been gathered since rc1,
but it's still fairly calm over all. The only largish LOC is found in
atmel driver, and it's just a removal of broken non-DT stuff. The
rest are all small driver-specific fixes, nothing to worry much"
* tag 'sound-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (26 commits)
ALSA: hda - One more Dell macine needs DELL1_MIC_NO_PRESENCE quirk
ALSA: opl3: small array underflow
ALSA: line6: Clamp values correctly
ALSA: msnd: add some missing curly braces
ASoC: omap-pcm: Correct dma mask
ASoC: simple-card: Add a NULL pointer check in asoc_simple_card_dai_link_of
ASoC: sam9g20_wm8731: drop machine_is_xxx
ALSA: dice: fix wrong offsets for Dice interface
ALSA: oxfw: fix a condition and return code in start_stream()
ASoC: OMAP: mcbsp: Fix CLKX and CLKR pinmux when used as inputs
ASoC: rt5677: Correct the routing paths of that after IF1/2 DACx Mux
ASoC: sta32x: fix register range in regmap.
ASoC: rt5670: Set RT5670_IRQ_CTRL1 non volatile
ASoC: Intel: reset the DSP while suspending
ASoC: Intel: save and restore the CSR register
ASoC: Intel: update MMX ID to 3
ASoC: max98357a: Add missing header files
ASoC: cirrus: tlv320aic23 needs I2C
ASoC: Samsung: add missing I2C/SPI dependencies
ASoC: rt5670: Fix the speaker mono output issue
...
Linus Torvalds [Fri, 6 Mar 2015 18:36:09 +0000 (10:36 -0800)]
Merge tag 'pm+acpi-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes for recent regressions (ACPI resources management,
suspend-to-idle), stable-candidate fixes (ACPI backlight), fixes
related to the wakeup IRQ management changes made in v3.18, other
fixes (suspend-to-idle, cpufreq ppc driver) and a couple of cleanups
(suspend-to-idle, generic power domains, ACPI backlight).
Specifics:
- Fix ACPI resources management problems introduced by the recent
rework of the code in question (Jiang Liu) and a build issue
introduced by those changes (Joachim Nilsson).
- Fix a recent suspend-to-idle regression on systems where entering
idle states causes local timers to stop, prevent suspend-to-idle
from crashing in restricted configurations (no cpuidle driver,
cpuidle disabled etc.) and clean up the idle loop somewhat while at
it (Rafael J Wysocki).
- Fix build problem in the cpufreq ppc driver (Geert Uytterhoeven).
- Allow the ACPI backlight driver module to be loaded if ACPI is
disabled which helps the i915 driver in those configurations
(stable-candidate) and change the code to help debug unusual use
cases (Chris Wilson).
- Wakeup IRQ management changes in v3.18 caused some drivers on the
at91 platform to trigger a warning from the IRQ core related to an
unexpected combination of interrupt action handler flags. However,
on at91 a timer IRQ is shared with some other devices (including
system wakeup ones) and that leads to the unusual combination of
flags in question.
To make it possible to avoid the warning introduce a new interrupt
action handler flag (which can be used by drivers to indicate the
special case to the core) and rework the problematic at91 drivers
to use it and work as expected during system suspend/resume. From
Boris Brezillon, Rafael J Wysocki and Mark Rutland.
- Clean up the generic power domains subsystem's debugfs interface
(Kevin Hilman)"
* tag 'pm+acpi-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
genirq / PM: describe IRQF_COND_SUSPEND
tty: serial: atmel: rework interrupt and wakeup handling
watchdog: at91sam9: request the irq with IRQF_NO_SUSPEND
cpuidle / sleep: Use broadcast timer for states that stop local timer
clk: at91: implement suspend/resume for the PMC irqchip
rtc: at91rm9200: rework wakeup and interrupt handling
rtc: at91sam9: rework wakeup and interrupt handling
PM / wakeup: export pm_system_wakeup symbol
genirq / PM: Add flag for shared NO_SUSPEND interrupt lines
ACPI / video: Propagate the error code for acpi_video_register
ACPI / video: Load the module even if ACPI is disabled
PM / Domains: cleanup: rename gpd -> genpd in debugfs interface
cpufreq: ppc: Add missing #include <asm/smp.h>
x86/PCI/ACPI: Relax ACPI resource descriptor checks to work around BIOS bugs
x86/PCI/ACPI: Ignore resources consumed by host bridge itself
cpuidle: Clean up fallback handling in cpuidle_idle_call()
cpuidle / sleep: Do sanity checks in cpuidle_enter_freeze() too
idle / sleep: Avoid excessive disabling and enabling interrupts
PCI: versatile: Update for list_for_each_entry() API change
genirq / PM: better describe IRQF_NO_SUSPEND semantics
Linus Torvalds [Fri, 6 Mar 2015 18:09:57 +0000 (10:09 -0800)]
Merge tag 'nfs-for-4.0-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- Fix a regression in the NFSv4 open state recovery code
- Fix a regression in the NFSv4 close code
- Fix regressions and side-effects of the loop-back mounted NFS fixes
in 3.18, that cause the NFS read() syscall to return EBUSY.
- Fix regressions around the readdirplus code and how it interacts
with the VFS lazy unmount changes that went into v3.18.
- Fix issues with out-of-order RPC call replies replacing updated
attributes with stale ones (particularly after a truncate()).
- Fix an underflow checking issue with RPC/RDMA credits
- Fix a number of issues with the NFSv4 delegation return/free code.
- Fix issues around stale NFSv4.1 leases when doing a mount"
* tag 'nfs-for-4.0-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (24 commits)
NFSv4.1: Clear the old state by our client id before establishing a new lease
NFSv4: Fix a race in NFSv4.1 server trunking discovery
NFS: Don't write enable new pages while an invalidation is proceeding
NFS: Fix a regression in the read() syscall
NFSv4: Ensure we skip delegations that are already being returned
NFSv4: Pin the superblock while we're returning the delegation
NFSv4: Ensure we honour NFS_DELEGATION_RETURNING in nfs_inode_set_delegation()
NFSv4: Ensure that we don't reap a delegation that is being returned
NFS: Fix stateid used for NFS v4 closes
NFSv4: Don't call put_rpccred() under the rcu_read_lock()
NFS: Don't require a filehandle to refresh the inode in nfs_prime_dcache()
NFSv3: Use the readdir fileid as the mounted-on-fileid
NFS: Don't invalidate a submounted dentry in nfs_prime_dcache()
NFSv4: Set a barrier in the update_changeattr() helper
NFS: Fix nfs_post_op_update_inode() to set an attribute barrier
NFS: Remove size hack in nfs_inode_attrs_need_update()
NFSv4: Add attribute update barriers to delegreturn and pNFS layoutcommit
NFS: Add attribute update barriers to NFS writebacks
NFS: Set an attribute barrier on all updates
NFS: Add attribute update barriers to nfs_setattr_update_inode()
...
Mathias Nyman [Fri, 6 Mar 2015 15:23:19 +0000 (17:23 +0200)]
xhci: Workaround for PME stuck issues in Intel xhci
The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.
Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks
Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)
xhci: fix reporting of 0-sized URBs in control endpoint
When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.
The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.
This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.
This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.
projects / linux-beck.git / log