ARM: keystone: Move CPU bringup code to dedicated asm file
Because of inline asm usage in platsmp.c, smc instruction
creates build failure for ARM V6+V7 build where as using instruction
encoding for smc breaks the thumb2 build.
So move the code snippet to separate asm file and mark
it with 'armv7-a$(plus_sec)' to avoid any build issues.
Arnd Bergmann [Mon, 3 Jun 2013 13:38:58 +0000 (15:38 +0200)]
ARM: multiplatform: always pick one CPU type
With the new default platform code, we can always boot using DT
without requiring a board file, but we cannot build a kernel
unless we select at least one CPU core, which breaks some
"randconfig" builds.
This adapts the ARCH_MULTI_V4T and ARCH_MULTI_V5 options so we
always default to a common CPU core if no platform was enabled
that picks something else. The default we pick for ARMv4T is
ARM920T, while for ARMv5 we pick ARM926T.
Mohammed, Afzal [Mon, 24 Jun 2013 08:13:45 +0000 (08:13 +0000)]
ARM: OMAP2+: AM43x: resolve SMP related build error
If AM43x and SMP is selected, OMAP4 & OMAP5 deselected, build error as
follows,
arch/arm/mach-omap2/built-in.o: In function `scu_gp_set':
arch/arm/mach-omap2/sleep44xx.S:131: undefined reference to `omap4_get_scu_base'
arch/arm/mach-omap2/sleep44xx.S:132: undefined reference to `scu_power_mode'
arch/arm/mach-omap2/built-in.o: In function `scu_gp_clear':
arch/arm/mach-omap2/sleep44xx.S:227: undefined reference to `omap4_get_scu_base'
arch/arm/mach-omap2/sleep44xx.S:229: undefined reference to `scu_power_mode'
Resolve it by building sleep44xx.S only for OMAP4 & OMAP5.
Signed-off-by: Afzal Mohammed <afzal@ti.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 21 Jun 2013 12:57:38 +0000 (14:57 +0200)]
Merge tag 'renesas-cleanup-boot-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Renesas ARM based SoC boot cleanup for v3.11
Work by Magnus Damm and others to clean up the boot of and move
things closer to supporting multi-arch.
As a side effect of this work it was decided to remove support for
two boards, Bonito and AP4EVB. Those patches are included in this
series as they depend on earlier patches in the series.
* tag 'renesas-cleanup-boot-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove Bonito board support
ARM: shmobile: Remove AP4EVB board support
ARM: shmobile: Remove mach/memory.h
ARM: shmobile: Remove MEMORY_START/SIZE
ARM: shmobile: Enable ARM_PATCH_PHYS_VIRT
ARM: shmobile: Remove old SCU boot code
ARM: shmobile: EMEV2 SMP with SCU boot fn and args
ARM: shmobile: sh73a0 SMP with SCU boot fn and args
ARM: shmobile: r8a7779 SMP with SCU boot fn and args
ARM: shmobile: Add SCU boot function using argument
ARM: shmobile: Add SMP boot function and argument
ARM: shmobile: Rework sh7372 sleep code to use virt_to_phys()
ARM: shmobile: Remove romImage CONFIG_MEMORY_START
ARM: shmobile: Let romImage rely on default ATAGS
ARM: shmobile: uImage load address rework
Arnd Bergmann [Fri, 21 Jun 2013 09:46:56 +0000 (11:46 +0200)]
Merge tag 'v3.11-rockchip-basics' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/soc
From Heiko Stuebner:
Adds basic support for Rockchip Cortex-A9 SoCs.
* tag 'v3.11-rockchip-basics' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
clocksource: dw_apb_timer_of: use clocksource_of_init
clocksource: dw_apb_timer_of: select DW_APB_TIMER
clocksource: dw_apb_timer_of: add clock-handling
clocksource: dw_apb_timer_of: enable the use the clocksource as sched clock
Heiko Stuebner [Sun, 2 Jun 2013 21:09:41 +0000 (23:09 +0200)]
arm: add basic support for Rockchip RK3066a boards
This adds a generic devicetree board file and a dtsi for boards
based on the RK3066a SoCs from Rockchip.
Apart from the generic parts (gic, clocks, pinctrl) the only components
currently supported are the timers, uarts and mmc ports (all DesignWare-
based).
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Olof Johansson <olof@lixom.net>
Heiko Stuebner [Thu, 13 Jun 2013 14:18:11 +0000 (16:18 +0200)]
arm: Add basic clocks for Rockchip rk3066a SoCs
This adds a basic clock setup for rk3066a SoCs. Only the gates are
set up currently, as the mux and dividers should use the upcoming
generic devicetree bindings.
Clocks whose rates need to be known are supplied by fixed-rate
"dummy"-clocks that provide the correct rate. This is uncritical insofar
that the only bootloader currently in existence for Rockchip devices
is the propietary Rockchip one that always setups the clocks in the
necessary way.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Mike Turquette <mturquette@linaro.org>
Arnd Bergmann [Thu, 20 Jun 2013 20:49:00 +0000 (22:49 +0200)]
Merge tag 'samsung-defconfig-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
From Kukjin Kim:
update exynos_defconfig
- enable GPIO buttons and RTC drivers
* tag 'samsung-defconfig-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: exynos_defconfig: Enable GPIO buttons and RTC drivers
Arnd Bergmann [Thu, 20 Jun 2013 20:36:11 +0000 (22:36 +0200)]
Merge tag 'remove-nondt-exynos-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
From Kukjin Kim:
cleanup and removing dead code for only support DT for exynos
- remove board file for exynos
- remove legacy files which are not used anymore
- decouple ARCH_EXYNOS from PLAT_S5P
* tag 'remove-nondt-exynos-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (35 commits)
ARM: EXYNOS: Remove remaining dead code after non-DT support removal
ARM: EXYNOS: Remove legacy L2X0 initialization
ARM: EXYNOS: Use exynos_init_io() as map_io callback
ARM: EXYNOS: Remove custom init_irq callbacks
ARM: EXYNOS: Remove mach/regs-usb-phy.h header
thermal: exynos: Support both EXYNOS4X12 SoCs
ARM: EXYNOS: Remove unused base addresses from mach/map.h header
ARM: EXYNOS: Remove mach/irqs.h header
ARM: EXYNOS: Select SPARSE_IRQ for Exynos
ARM: SAMSUNG: Make legacy MFC support code depend on SAMSUNG_ATAGS
ARM: EXYNOS: Remove mach/regs-gpio.h header
ARM: EXYNOS: Remove mach/gpio.h
ARM: EXYNOS: Remove setup-i2c0.c
ARM: EXYNOS: Do not select legacy Kconfig symbols any more
ARM: SAMSUNG: Include most of mach/ headers conditionally
ARM: EXYNOS: Decouple ARCH_EXYNOS from PLAT_S5P
USB: Check for ARCH_EXYNOS separately
platform: Check for ARCH_EXYNOS separately
ARM: SAMSUNG: Compile legacy IRQ and GPIO PM code only with ATAGS support
ARM: EXYNOS: Provide compatibility stubs for PM code in pm-core.h header
...
Arnd Bergmann [Thu, 20 Jun 2013 19:50:51 +0000 (21:50 +0200)]
Merge tag 'exynos-arch-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
From Kukjin Kim:
arch/arm/mach-exynos update
- enable XHCI on exynos5
- enable Pinctrl on exynos4 and exynos5
- calling scu_enable() is only available on Cortex-A9
* tag 'exynos-arch-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: call scu_enable() only in case of cortex-A9 processor
ARM: EXYNOS: Select PINCTRL_EXYNOS for exynos4/5 at chip level
ARM: EXYNOS: Enable XHCI support on exynos5
Arnd Bergmann [Thu, 20 Jun 2013 14:38:12 +0000 (16:38 +0200)]
Merge tag 'omap-for-v3.11/soc-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Fix am43x minimal booting as I accidentally left out one
patch from the already merged omap-for-v3.11/soc-signed branch.
Also fixes for ti81x booting and revision check updates.
These are based on omap-for-v3.11/soc-signed because of the
am43x dependency to earlier patches.
* tag 'omap-for-v3.11/soc-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3+: am33xx id: Add new am33xx specific function to check dev_feature
ARM: OMAP: TI816X: add powerdomains for TI816x
ARM: OMAP2: TI81XX: id: Add cpu id for TI816x ES2.0 and ES2.1
ARM: OMAP2+: AM43x: basic dt support
Arnd Bergmann [Thu, 20 Jun 2013 13:06:57 +0000 (15:06 +0200)]
Merge tag 'davinci-for-v3.11/soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
From Sekhar Nori:
DaVinci SoC changes for v3.11
This pull request moves DaVinci EDMA library to
arch/arm/common so it can be used by OMAP based AM335x.
This is a temporary step until all drivers are converted
to use the dmaengine driver in drivers/dma/edma.c.
Several drivers like SPI, MMC/SD have already been converted.
Some like audio are pending.
The other two patches in the pull request are cleanup in nature.
* tag 'davinci-for-v3.11/soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: edma: remove unused transfer controller handlers
ARM: davinci: move private EDMA API to arm/common
ARM: davinci: remove __init atrribute from function declaration
Thomas Petazzoni [Thu, 20 Jun 2013 07:45:26 +0000 (09:45 +0200)]
arm: mvebu: fix coherency_late_init() for multiplatform
As noticed by Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>, commit 865e0527d2d7 ('arm: mvebu: avoid hardcoded virtual address in
coherency code') added a postcore_initcall() to register the bus
notifier that the mvebu code needs to apply correct DMA operations on
its platform devices breaks the multiplatform boot on other platforms,
because the bus notifier registration is unconditional.
This commit fixes that by registering the bus notifier only if we have
the mvebu coherency unit described in the Device Tree. The conditional
used is exactly the same in which the bus_register_notifier() call was
originally enclosed before 865e0527d2d7 ('arm: mvebu: avoid hardcoded
virtual address in coherency code').
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Arnd Bergmann [Thu, 20 Jun 2013 00:14:59 +0000 (02:14 +0200)]
Merge tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
imx soc changes for 3.11:
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
* tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (29 commits)
ARM: imx_v6_v7_defconfig: Enable Vybrid VF610
ARM: imx_v6_v7_defconfig: Enable imx-wm8962 by default
ARM: clk-imx6qdl: Add clko1 configuration for imx6qdl-sabresd
ARM: imx_v6_v7_defconfig: Enable PWM and backlight options
ARM: imx: Remove mxc specific ulpi access ops
ARM: imx: add initial support for VF610
ARM: imx: add VF610 clock support
ARM: imx_v6_v7_defconfig: enable parallel display
ARM: imx: clk: No need to initialize phandle struct
ARM: imx: irq-common: Include header to avoid sparse warning
ARM: imx: Enable mx6 solo-lite support
ARM: imx6: use common of_clk_init() call to initialize clocks
ARM: imx6q: call of_clk_init() to register fixed rate clocks
ARM: imx: imx_v6_v7_defconfig: Select CONFIG_DRM_IMX_TVE
ARM: i.MX6: clk: add different DualLite MLB clock config
ARM i.MX5: Add S/PDIF clocks
ARM i.MX53: Add SATA clock
ARM: imx6q: clk: add the eim_slow clock
ARM: imx: remove MLB PLL from pllv3
ARM: imx: disable pll8_mlb in mx6q_clks
...
Arnd Bergmann [Wed, 19 Jun 2013 23:51:18 +0000 (01:51 +0200)]
Merge tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/soc
From Linus Walleij:
Device Tree and Multiplatform support for U300:
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
* tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (40 commits)
ARM: u300: switch to using syscon regmap for board
ARM: u300: Update MMC configs for u300 defconfig
spi: pl022: use DMA by default when probing from DT
pinctrl: get rid of all platform data for coh901
ARM: u300: convert MMC/SD clock to device tree
ARM: u300: move the gated system controller clocks to DT
i2c: stu300: do not request a specific clock name
clk: move the U300 fixed and fixed-factor to DT
ARM: u300: remove register definition file
ARM: u300: add syscon node
ARM: u300 use module_spi_driver to register driver
ARM: u300: delete remnant machine headers
ARM: u300: convert to multiplatform
ARM: u300: localize <mach/u300-regs.h>
ARM: u300: delete <mach/irqs.h>
ARM: u300: delete <mach/hardware.h>
ARM: u300: push down syscon registers
ARM: u300: remove deps from debug macro
ARM: u300: move debugmacro to debug includes
ARM: u300: delete all static board data
...
Arnd Bergmann [Wed, 19 Jun 2013 23:00:15 +0000 (01:00 +0200)]
Merge tag 'integrator-pci-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/soc
From Linus Walleij:
This is a patch series that:
- Pulls the Integrator/AP PCI bridge driver into one file
- Adds full device tree support for it
- Keeps ATAG support around for the time being
* tag 'integrator-pci-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: basic PCIv3 device tree support
ARM: integrator: move static ioremapping into PCIv3 driver
ARM: integrator: move VGA base assignment
ARM: integrator: remap PCIv3 base dynamically
ARM: integrator: move V3 register definitions into driver
ARM: integrator: move PCI base address grab to probe
ARM: integrator: grab PCI error IRQ in probe()
ARM: integrator: convert PCIv3 bridge to platform device
ARM: integrator: merge PCIv3 driver into one file
ARM: pci: create pci_common_init_dev()
Documentation/devicetree: add a small note on PCI
Doug Anderson [Mon, 10 Jun 2013 09:26:53 +0000 (18:26 +0900)]
ARM: EXYNOS: Select PINCTRL_EXYNOS for exynos4/5 at chip level
Previously if you had MACH_EXYNOS5_DT but not MACH_EXYNOS4_DT you'd be
missing the pincontrol definitions. Move PINCTRL selects to the arch
level since we should be enabling the code for all exynos variants.
Update the PINCTRL descriptions to indicate that PINCTRL_EXYNOS is not
for exynos5440. Also add basic dependencies for the PINCTRL_EXYNOS
kernel config.
Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Arnd Bergmann [Tue, 18 Jun 2013 16:36:52 +0000 (01:36 +0900)]
ARM: EXYNOS: Remove legacy L2X0 initialization
Since Exynos is now supporting only DT-based boot, the old L2X0
initialization code is not needed anymore, so exynos4_l2x0_cache_init()
can be greatly simplified.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Arnd Bergmann [Tue, 18 Jun 2013 16:36:47 +0000 (01:36 +0900)]
ARM: EXYNOS: Use exynos_init_io() as map_io callback
Since there is no board specific mapping needed on Exynos,
exynos_init_io() can be simplified and used as map_io callback for both
Exynos4 and Exynos5.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Arnd Bergmann [Tue, 18 Jun 2013 16:35:22 +0000 (01:35 +0900)]
ARM: EXYNOS: Remove custom init_irq callbacks
Since both exynos4_init_irq() and exynos5_init_irq() are just calling
irqchip_init(), there is no need for them to exist any more, since this
is the default that is called when init_irq callback is not specified.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tomasz Figa [Sat, 15 Jun 2013 00:29:25 +0000 (09:29 +0900)]
ARM: EXYNOS: Remove unused base addresses from mach/map.h header
This patch removes all the unused base addresses from mach/map.h header,
leaving only addresses of IPs that currently use static IO mapping or
need the address hardcoded, like low level debug UART.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tomasz Figa [Sat, 15 Jun 2013 00:28:55 +0000 (09:28 +0900)]
ARM: EXYNOS: Select SPARSE_IRQ for Exynos
This patch adds selection of CONFIG_SPARSE_IRQ for ARCH_EXYNOS, since it
is required by multiplatform and allows to remove the legacy mach/irqs.h
header.
To make this possible, a dummy IRQ_EINT_BIT macro is added to pm-core.h
header to allow plat-samsung/pm.c compile. This macro is irrelevant for
Exynos and will be removed after reworking Samsung pm code for
multiplatform compatibility.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tomasz Figa [Tue, 18 Jun 2013 16:28:56 +0000 (01:28 +0900)]
ARM: SAMSUNG: Make legacy MFC support code depend on SAMSUNG_ATAGS
This allows to bypass compilation of static platform device and resource
definitions that require interrupts and base addresses to be defined
statically.
Cc: Jeongtae Park <jtp.park@samsung.com> Cc: Kamil Debski <k.debski@samsung.com> Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tomasz Figa [Tue, 18 Jun 2013 16:27:37 +0000 (01:27 +0900)]
ARM: EXYNOS: Do not select legacy Kconfig symbols any more
This patch removes selection of several legacy Kconfig symbols from
ARCH_EXYNOS to bypass compilation of code used only for ATAGS based
boot.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tomasz Figa [Sat, 15 Jun 2013 00:17:33 +0000 (09:17 +0900)]
ARM: SAMSUNG: Include most of mach/ headers conditionally
Since it is illegal to include mach/ headers from source files outside
of respective mach-* directory and DT-only Samsung platforms might not
have all of them anyway, this patches makes inclusion of them
conditional, based on CONFIG_SAMSUNG_ATAGS.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tomasz Figa [Tue, 18 Jun 2013 16:26:42 +0000 (01:26 +0900)]
ARM: EXYNOS: Decouple ARCH_EXYNOS from PLAT_S5P
After removing support for ATAGS based boot on Exynos, there is not much
that can be shared between Exynos and other S5P platforms. This patch
makes Exynos a standalone Samsung platform, not using PLAT_S5P.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tomasz Figa [Tue, 18 Jun 2013 16:25:48 +0000 (01:25 +0900)]
USB: Check for ARCH_EXYNOS separately
ARCH_EXYNOS is going to be excluded from PLAT_S5P, so it must be checked
separately in Exynos-related Kconfig entries.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tomasz Figa [Tue, 18 Jun 2013 16:24:12 +0000 (01:24 +0900)]
ARM: SAMSUNG: Compile legacy IRQ and GPIO PM code only with ATAGS support
This patch adds new Kconfig symbols, SAMSUNG_PM_GPIO and S5P_IRQ_PM that
get enabled when GPIO_SAMSUNG, PM and S5P_PM are enabled, but only if
SAMSUNG_ATAGS is selected.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Kconfig entry that selects whether legacy Samsung GPIO
driver should be built or not. For platforms that support only DT based
boot, the new pinctrl driver is used and so the old one is not needed.
Cc: Grant Likely <grant.likely@linaro.org> Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tushar Behera [Tue, 18 Jun 2013 15:35:01 +0000 (00:35 +0900)]
ARM: exynos_defconfig: Enable GPIO buttons and RTC drivers
Many of the boards use GPIO-mapped buttons for generic input.
For Arndale board, these buttons also serve as wakeup source.
And the issues reported in commit 522ccdb6fd0e ("ARM: dts:
Disable the RTC by default on exynos5") are no longer reproduced
on EXYNOS5250 based systems. Hence it would be better to re-enable
RTC support for EXYNOS5250.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
[mturquette@linaro.org: ack on RTC enabling] Acked-by: Mike Turquette <mturquette@linaro.org> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Vaibhav Hiremath [Fri, 17 May 2013 10:13:41 +0000 (15:43 +0530)]
ARM: OMAP3+: am33xx id: Add new am33xx specific function to check dev_feature
Layout of DEV_FEATURE register (offset = 0x604) is different
between TI81xx and AM33xx device, so create separate function
which will check for features available on specific AM33xx SoC
and set the flags accordingly.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Reviewed-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Aida Mynzhasova [Thu, 30 May 2013 15:04:50 +0000 (19:04 +0400)]
ARM: OMAP: TI816X: add powerdomains for TI816x
This patch adds required structures for powerdomain initialization on
the ti816x. It is impossible to use omap3430 structures in order to
initialize powerdomains on ti816x, because there are big differences
between PRCM module base address offsets on these CPUs.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru> Signed-off-by: Tony Lindgren <tony@atomide.com>
Olof Johansson [Tue, 18 Jun 2013 07:23:04 +0000 (00:23 -0700)]
Merge tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/soc
From Santosh Shilimkar:
SOC support for Keystone II devices:
- Minimal machine and device-tree support with arch_timers and console UART
- Reboot hook using PLL reset
- Low level debug support using UART
- SMP boot support
* tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: keystone: Enable SMP support on Keystone machines
ARM: keystone: Add minimal TI Keystone platform support
ARM: dts: keystone: Add minimal Keystone SOC device tree data
Matt Porter [Wed, 6 Mar 2013 16:15:32 +0000 (11:15 -0500)]
ARM: edma: remove unused transfer controller handlers
Fix build on OMAP, the irqs are undefined on AM33xx.
These error interrupt handlers were hardcoded as disabled
so since they are unused code, simply remove them.
Signed-off-by: Matt Porter <mporter@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Matt Porter [Wed, 6 Mar 2013 16:15:31 +0000 (11:15 -0500)]
ARM: davinci: move private EDMA API to arm/common
Move mach-davinci/dma.c to common/edma.c so it can be used
by OMAP (specifically AM33xx) as well.
Signed-off-by: Matt Porter <mporter@ti.com> Acked-by: Chris Ball <cjb@laptop.org> # davinci_mmc.c Acked-by: Mark Brown <broonie@linaro.org> Acked-by: Olof Johansson <olof@lixom.net>
[nsekhar@ti.com: dropped davinci sffsdr changes] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
ARM: keystone: Add minimal TI Keystone platform support
Texas Instruments Keystone family of multi-core devices are
based on ARM Cortex A15. Patch adds basic definitions for a
new Keystone sub-architecture in ARM.
The TCI66xxK2H Communications Infrastructure Keystone SoCs
are member of the C66x family based on TI's new KeyStone 2
multi-core SoC Architecture designed specifically for high
performance wireless and networking infrastructure applications.
The SOCs contains many subsystems like Cortex A15 ARM CorePacs,
C66XX DSP CorePacs, MSMC memory controller, Tera Net bus,
IP Network, Navigator, Hyperlink, 1G/10G Ethernet, Radio layers
and queue based communication systems.
Rajendra Nayak [Mon, 17 Jun 2013 13:16:23 +0000 (18:46 +0530)]
ARM: AM33xx: Remove the unused voltagedomain data
Now that there is a way to tell the powerdomain core about
missing voltage domain auto-scaling control in SoCs', get rid of the dummy
voltage domain data populated for AM33xx devices.
Rajendra Nayak [Mon, 17 Jun 2013 13:16:22 +0000 (18:46 +0530)]
ARM: OMAP2+: Powerdomain: Remove the need to always have a voltdm associated to a pwrdm
The powerdomain framework currently expects all powerdomains to be associated with
a corresponding voltagedomain. For some SoCs' (like the already existing AM33xx
family, or for the upcoming AM437x and DRA7 SoCs') which
do not have a Voltage controller/Voltage Processor (neither the SR I2C
bus to communicate with the PMIC) there is no need for a Powerdomain to have
a voltage domain association since there is no auto-scaling of voltages possible
using the voltage FSM.
Extend the arch operations to add an api which the powerdomain core can
then use to identify if a voltdm lookup and association for a powerdomain
is really needed.
Linus Walleij [Thu, 13 Jun 2013 19:21:31 +0000 (21:21 +0200)]
ARM: u300: switch to using syscon regmap for board
This switches the code using a local remapping of the
system controller to enable the U300 board to be
self-powered over to making the U300-specific syscon
compatible with the MFD generic syscon driver, selecting
the generic syscon driver, and augmenting the board
power code to pick the regmap and manipulate the syscon
from the regmap side of things.
Ulf Hansson [Mon, 27 May 2013 12:41:55 +0000 (14:41 +0200)]
ARM: u300: Update MMC configs for u300 defconfig
Enable MMC_UNSAFE_RESUME to be accomplish a proper suspend/resume cycle
for SD/SDIO/(e)MMC.
ARMMMCI host driver supports clock gating through runtime PM, thus
MMC_CLKGATE is not needed. Moreover ARMMMCI can do scatter-gather which
means we can explicity disable MMC_BLOCK_BOUNCE, since it's default
enabled, to skip unnecessary bounce buffer copying.
Linus Walleij [Thu, 23 May 2013 17:46:40 +0000 (19:46 +0200)]
spi: pl022: use DMA by default when probing from DT
In the past we controlled the selection of DMA for a certain
host by a boolean switch in the platform data. Currently
there is no way to enable DMA on a PL022 probed from the
device tree. Let's default to trying to obtain DMA channels
in the DT case, and then we can always fail (and thus fall
back to PIO mode).
Linus Walleij [Thu, 23 May 2013 18:09:43 +0000 (20:09 +0200)]
pinctrl: get rid of all platform data for coh901
This deletes the dependency on any platform data for
the COH901 pin controller. There is only one user in the
kernel, and if we at some point want to support more
variants, they shall provide their variant info through
the device tree.
Linus Walleij [Thu, 23 May 2013 13:26:29 +0000 (15:26 +0200)]
i2c: stu300: do not request a specific clock name
We have used the default clock associated with the block
for a long time, only heuristics in the clock system has
made this work anyway. This needs to be done away with as
we start probing this driver and its clocks exclusively
from the device tree.
Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 22 May 2013 14:20:27 +0000 (16:20 +0200)]
ARM: u300: remove register definition file
Now that the core file is the only one actually using any
of the base addresses, we can delete that header and move
the base address definitions into the one and only core
file.
Linus Walleij [Wed, 22 May 2013 14:15:13 +0000 (16:15 +0200)]
ARM: u300: add syscon node
This adds a device tree node for the U300 system controller
and remaps this dynamically instead of using hard-coded
virtual addresses. The board power set-up code is altered
to fetch a reference to the syscon using ampersand <&syscon>
notation. This way of passing a pointer to the syscon will
also be used by the clocks.
Linus Walleij [Thu, 2 May 2013 16:07:11 +0000 (18:07 +0200)]
ARM: u300: delete remnant machine headers
Two files remain in <mach/*> for U300: timex.h and
uncompress.h. The former is done away with by using
defaults, the latter is unused in multiplatform.
Linus Walleij [Thu, 2 May 2013 16:01:46 +0000 (18:01 +0200)]
ARM: u300: convert to multiplatform
Now that we removed our dependency on <mach/*> the U300
can be converted to mutliplatform. Remove the invalid restriction
that U300 would not support AUTO_ZRELADDR (it does) and update
the defconfig in the process.
Linus Walleij [Thu, 2 May 2013 14:56:15 +0000 (16:56 +0200)]
ARM: u300: push down syscon registers
Get rid of the <mach/syscon.h> header as a prerequisite for
multiplatform support. Do this by pushing the registers down
to their respective drivers and deleting the unused remainder.
Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 2 May 2013 15:00:29 +0000 (17:00 +0200)]
ARM: u300: remove deps from debug macro
This rids the dependency to <mach/hardware.h> (which is an
implicit dependency to <mach/u300-regs.h>) from the U300
debug macro. Take this opportunity to update the file
header.
We have now transferred all the U300 peripherals to the device
tree, so we just select USE_OF, and delete all static board data,
then require that this platform shall be booted using the device
tree and nothing else.
This gets rid of the MMCI (PL180), PL022, and serial PL011
platform data entries and more.
This registers the U300 FSMC flash controller from the
device tree, and defines the three partitions. Skip the
BBT scan as in the current platform data.
This registers the PL022 PrimeCell from the U300 device
tree. We make a new copy of the platform data for the
device tree boot path, as the old platform data is in an
older file which will be going away.
ARM: u300: add the COH 901 318 DMAC to device tree
This adds the COH 901 318 DMA controller to the U300
device tree. All devices now converted to device tree
so far will start to find their DMA channels.
Note that the U300 is not yet using the device tree
to obtain DMA channels, but this is a first step.
Linus Walleij [Thu, 2 May 2013 08:38:52 +0000 (10:38 +0200)]
ARM: u300: augment device tree with DMA channels
This adds DMA channel assignments to the MMC/SD-controller
and the two UARTs already in the U300 device tree, as we
have now defined a way to obtain DMA channels from the
device tree.
Now that we have enabled board power and the AB3100 regulators,
put the regulator data into the device tree and enable it so
we can start to tie regulators to devices. To begin with we're
only supplying the power to the board itself.
Cc: Mark Brown <broonie@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for setting up the board power from the
device tree on the U300. We use a board-specific node in the
device tree for the S365 board and bind a regulator for the
board power to this node.
Cc: Mark Brown <broonie@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Markus Pargmann [Thu, 6 Jun 2013 12:41:57 +0000 (14:41 +0200)]
ARM: imx: Remove mxc specific ulpi access ops
There are ulpi access ops implemented in drivers/usb/phy/phy-ulpi.c.
mxc access ops implement the same access operations within mach-imx. This
patch removes the mxc ulpi file and uses phy-ulpi instead for
imx_otg_ulpi_create.
phy-ulpi successfully tested with i.MX27 Phytec phyCARD-S (pca100).
projects / linux-beck.git / log