Russell King [Wed, 23 Jan 2008 12:34:16 +0000 (12:34 +0000)]
[ARM] pxa: fix PXA27x resume
When PXA27x wakes up, tick_resume_oneshot() tries to set a timer
interrupt to occur immediately. Since PXA27x requires at least
MIN_OSCR_DELTA, this causes us to flag an error.
tick_program_event() then increments the next event time by
min_delta_ns. However, by the time we get back to programming
the next event, the OSCR has incremented such that we fail again.
We repeatedly retry, but the OSCR is too fast for us - we never
catch up, so we never break out of the loop - resulting in us
never apparantly resuming.
Fix this by doubling min_delta_ns.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 7 Jan 2008 22:18:30 +0000 (22:18 +0000)]
[ARM] pxa: Add PXA3 standby code hooked into the IRQ wake scheme
Wakeup sources on PXA3 are enabled at two levels. First, the MFP
configuration has to be set to enable which edges a specific pin
will trigger a wakeup. The pin also has to be routed to a functional
unit. Lastly, the functional unit must be enabled as a wakeup source
in the appropriate AD*ER registers (AD2D0ER for standby resume.)
This doesn't fit well with the IRQ wake scheme - we currently do a
best effort conversion from IRQ numbers to functional unit wake enable
bits. For instance, there's several USB client related enable bits but
there's no corresponding IRQs to determine which you'd want. Conversely,
there's a single enable bit covering several functional units.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 8 Jan 2008 15:12:22 +0000 (15:12 +0000)]
[ARM] pxa: program MFPs for low power mode when suspending
Hook the MFP code into the power management code so that the MFPs can
be reconfigured when suspending and resuming. However, note the FIXME
- low power mode MFP configuration may depend on the system state being
entered.
Also note that we have to clear any detected edge events prior to
entering a low power mode - otherwise we immediately wake up.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
eric miao [Thu, 3 Jan 2008 03:25:56 +0000 (11:25 +0800)]
[ARM] pxa: make MFP configuration processor independent
There are two reasons for making the MFP configuration to be processor
independent, i.e. removing the relationship of configuration bits with
actual MFPR register settings:
1. power management sometimes requires the MFP to be configured
differently when in run mode or in low power mode
2. for future integration of pxa{25x,27x} GPIO configurations
The modifications include:
1. introducing of processor independent MFP configuration bits, as
defined in [include/asm-arm/arch-pxa/mfp.h]:
bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
bit 10..12 - Alternate Function Selection
bit 13..15 - Drive Strength
bit 16..18 - Low Power Mode State
bit 19..20 - Low Power Mode Edge Detection
bit 21..22 - Run Mode Pull State
and so on,
2. moving the processor dependent code from mfp.h into mfp-pxa3xx.h
3. cleaning up of the MFPR bit definitions
4. mapping of processor independent MFP configuration into processor
specific MFPR register settings is now totally encapsulated within
pxa3xx_mfp_config()
5. using of "unsigned long" instead of invented type of "mfp_cfg_t"
according to Documentation/CodingStyle Chapter 5, usage of this
in platform code will be slowly removed in later patches
Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa3xx_mfp_set_xxx() functions are originally provided for overwriting
MFP configurations performed by pxa3xx_mfp_config(), the usage of such
a dirtry trick is not recommended, since there is currently no user of
these functions, they are safely removed
Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 4 Jan 2008 22:41:09 +0000 (22:41 +0000)]
[ARM] pxa: increase size of memory mapping
The mapping for physical address 0x48000000 is not sufficient
to allow access to the dynamic memory controller configuration
registers on PXA3. These registers need to be accessed to
reconfigure the SDRAM when waking from a low power mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Philipp Zabel [Fri, 21 Dec 2007 08:31:25 +0000 (09:31 +0100)]
[ARM] 4718/1: Fix redefinition warnings in PXA uncompressor code
FFUART and friends are already defined as __REG(x) in pxa-regs.h.
Instead of redefining them here, we can just provide the __REG macro.
Including asm/arch/hardware.h is not an option because this physical
addresses are needed here.
This is a fix for the compiler warnings generated by 4663/1.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Nicolas Pitre <nico@cam.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Bridge Wu [Fri, 14 Dec 2007 09:40:25 +0000 (10:40 +0100)]
[ARM] 4711/1: pxa: mmc: move DMA specific code to platform layer
This patch is to move pxamci DMA specific code to corresponding
platform layer because using DRCMRRXMMC/DRCMRTXMMC in pxamci.c makes
the driver code dedicated to platform which is not extensible.
It is applicable to all pxa platforms.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Bridge Wu [Thu, 13 Dec 2007 06:24:30 +0000 (07:24 +0100)]
[ARM] 4709/1: pxa: mmc: add 26MHz support for pxa3[0|1]0 mmc controller
pxa3[0|1]0 mmc controller can support 26MHz clock mode, they support
SD spec 1.1 and MMC spec 4.0 which specify high speed mode. So host
caps will include MMC_CAP_MMC_HIGHSPEED and MMC_CAP_SD_HIGHSPEED for
pxa3[0|1]0.
This patch is to add 26MHz support for them. pxa host clock will be
set to 26MHz mode when the card supported max clock rate is higher
than or equal to 26MHz.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com> Acked-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Philipp Zabel [Thu, 22 Nov 2007 16:57:30 +0000 (17:57 +0100)]
[ARM] 4663/1: Only putc uncompressor output into FFUART if it was enabled by the bootloader
Also, use existing register and bit definitions instead of numbers.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Nicolas Pitre <nico@cam.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 12 Nov 2007 22:49:58 +0000 (22:49 +0000)]
[ARM] pxa/sa1100: replace wakeup support
Replace wakeup support using the alarm via the SA1100 RTC driver on
SA1100 and PXA platforms. This allows RTC alarm wakeup to be enabled
via sysfs using the conventional attributes.
Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 12 Nov 2007 22:48:12 +0000 (22:48 +0000)]
[ARM] pxa: Don't wind OSCR backwards over suspend/resume
OSCR is supposed to monotonically increment; however restoring it
to a time prior to OSMR0 may result in it being wound backwards.
Instead, if OSMR0 is within the minimum expiry time, wind OSMR0
forwards.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 12 Nov 2007 22:45:16 +0000 (22:45 +0000)]
[ARM] pxa: remove periodic mode emulation support
Apparantly, the generic time subsystem can accurately emulate periodic
mode via the one-shot support code, so we don't need our own periodic
emulation code anymore. Just ensure that we build support for one shot
into the generic time subsystem.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
Linus Torvalds [Sat, 26 Jan 2008 01:08:28 +0000 (17:08 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (67 commits)
fix drivers/ata/sata_fsl.c double-decl
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
pata_legacy: Merge winbond support
ata_generic: Cenatek support
pata_winbond: error return
pata_serverworks: Fix cable types and cosmetics
pata_mpc52xx: remove un-needed assignment
libata: fix off-by-one in error categorization
ahci: factor out AHCI enabling and enable AHCI before reading CAP
ata_piix: implement SIDPR SCR access
ata_piix: convert to prepare - activate initialization
libata: factor out ata_pci_activate_sff_host() from ata_pci_one()
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
pata_legacy: resychronize with upstream changes and resubmit
[libata] pata_legacy: typo fix
[libata] pata_winbond: update for new ->data_xfer hook
pata_pcmcia: convert to new data_xfer prototype
libata annotations and fixes
libata: use dev_driver_string() instead of "libata" in libata-sff.c
ata_piix: kill unused constants and flags
...
Mark Fasheh [Thu, 24 Jan 2008 02:35:31 +0000 (18:35 -0800)]
ocfs2: clean up bh null checks
If we know a buffer_head is non-null, then brelse() is unnecessary and
put_bh() can be used instead. Also, an explicit check for NULL is
unnecessary when using brelse(). This patch only covers buffer_head_io.c and
resize.c, which have recently added code which exhibits this problem.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mark Fasheh [Thu, 24 Jan 2008 00:54:48 +0000 (16:54 -0800)]
ocfs2: document access rules for blocked_lock_list
ocfs2_super->blocked_lock_list and ocfs2_super->blocked_lock_count have some
usage restrictions which aren't immediately obvious to anyone reading the
code. It's a good idea to document this so that we avoid making costly
mistakes in the future.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Joonwoo Park [Wed, 26 Dec 2007 03:09:57 +0000 (12:09 +0900)]
configfs: file.c fix possible recursive locking
configfs_register_subsystem() with default_groups triggers recursive locking.
it seems that mutex_lock_nested is needed.
=============================================
[ INFO: possible recursive locking detected ]
2.6.24-rc6 #145
---------------------------------------------
swapper/1 is trying to acquire lock:
(&sb->s_type->i_mutex_key#3){--..}, at: [<c40c9a9e>] configfs_add_file+0x2e/0x70
but task is already holding lock:
(&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca985>] configfs_register_subsystem+0x55/0x130
other info that might help us debug this:
1 lock held by swapper/1:
#0: (&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca985>] configfs_register_subsystem+0x55/0x130
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com> Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Joonwoo Park [Wed, 26 Dec 2007 03:09:57 +0000 (12:09 +0900)]
configfs: dir.c fix possible recursive locking
configfs_register_subsystem() with default_groups triggers recursive locking.
it seems that mutex_lock_nested is needed.
=============================================
[ INFO: possible recursive locking detected ]
2.6.24-rc6 #141
---------------------------------------------
swapper/1 is trying to acquire lock:
(&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca76f>] configfs_attach_group+0x4f/0x190
but task is already holding lock:
(&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca9d5>] configfs_register_subsystem+0x55/0x130
other info that might help us debug this:
1 lock held by swapper/1:
#0: (&sb->s_type->i_mutex_key#3){--..}, at: [<c40ca9d5>] configfs_register_subsystem+0x55/0x130
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com> Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Tao Ma [Thu, 10 Jan 2008 07:20:55 +0000 (15:20 +0800)]
ocfs2/dlm: Clear joining_node on hearbeat node down
Currently the process of dlm join contains 2 steps: query join and assert join.
After query join, the joined node will set its joining_node. So if the joining
node happens to panic before the 2nd step, the joined node will fail to clear
its joining_node flag because that node isn't in the domain map. It at least
cause 2 problems.
1. All the new join request will fail. So no new node can mount the volume.
2. The joined node can't umount the volume since during the umount process it
has to wait for the joining_node to be unknown. So the umount will be hanged.
The solution is to clear the joining_node before we check the domain map.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Sunil Mushran [Wed, 7 Nov 2007 00:10:23 +0000 (16:10 -0800)]
ocfs2: Update default cluster timeouts
Lots of people are having trouble with the default timeouts, which are too
low. These new values are derived from an informal survey taken on
ocfs2-users, as well as data from bug reports. This should reduce the amount
of cluster disconnects and subsequent fencing seen during normal workloads.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Jan Kara [Wed, 19 Dec 2007 14:24:09 +0000 (15:24 +0100)]
ocfs2: Safer read_inline_data()
In ocfs2_read_inline_data() we should store file size in loff_t. Although
the file size should fit in 32 bits we cannot be sure in case filesystem is
corrupted.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Jan Kara [Thu, 10 Jan 2008 23:11:45 +0000 (00:11 +0100)]
ocfs2: Silence false lockdep warnings
Create separate lockdep lock classes for system file's i_mutexes. They are
used to guard allocations and similar things and thus rank differently
than i_mutex of a regular file or directory.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mark Fasheh [Fri, 21 Dec 2007 00:49:04 +0000 (16:49 -0800)]
[PATCH 2/2] ocfs2: cluster aware flock()
Hook up ocfs2_flock(), using the new flock lock type in dlmglue.c. A new
mount option, "localflocks" is added so that users can revert to old
functionality as need be.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mark Fasheh [Fri, 21 Dec 2007 00:43:10 +0000 (16:43 -0800)]
[PATCH 1/2] ocfs2: add flock lock type
This adds a new dlmglue lock type which is intended to back flock()
requests.
Since these locks are driven from userspace, usage rules are much more
liberal than the typical Ocfs2 internal cluster lock. As a result, we can't
make use of most dlmglue features - lock caching and lock level
optimizations in particular. Additionally, userspace is free to deadlock
itself, so we have to deal with that in the same way as the rest of the
kernel - by allowing a signal to abort a lock request.
In order to keep ocfs2_cluster_lock() complexity down, ocfs2_file_lock()
does it's own dlm coordination. We still use the same helper functions
though, so duplicated code is kept to a minimum.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Sunil Mushran [Thu, 20 Dec 2007 22:58:11 +0000 (14:58 -0800)]
ocfs2: Local alloc window size changeable via mount option
Local alloc is a performance optimization in ocfs2 in which a node
takes a window of bits from the global bitmap and then uses that for
all small local allocations. This window size is fixed to 8MB currently.
This patch allows users to specify the window size in MB including
disabling it by passing in 0. If the number specified is too large,
the fs will use the default value of 8MB.
mount -o localalloc=X /dev/sdX /mntpoint
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mark Fasheh [Wed, 7 Nov 2007 22:40:36 +0000 (14:40 -0800)]
ocfs2: Support commit= mount option
Mostly taken from ext3. This allows the user to set the jbd commit interval,
in seconds. The default of 5 seconds stays the same, but now users can
easily increase the commit interval. Typically, this would be increased in
order to benefit performance at the expense of data-safety.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Tao Ma [Tue, 18 Dec 2007 07:47:25 +0000 (15:47 +0800)]
[PATCH 2/2] ocfs2: Implement group add for online resize
This patch adds the ability for a userspace program to request that a
properly formatted cluster group be added to the main allocation bitmap for
an Ocfs2 file system. The request is made via an ioctl, OCFS2_IOC_GROUP_ADD.
On a high level, this is similar to ext3, but we use a different ioctl as
the structure which has to be passed through is different.
During an online resize, tunefs.ocfs2 will format any new cluster groups
which must be added to complete the resize, and call OCFS2_IOC_GROUP_ADD on
each one. Kernel verifies that the core cluster group information is valid
and then does the work of linking it into the global allocation bitmap.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Tao Ma [Tue, 18 Dec 2007 07:47:03 +0000 (15:47 +0800)]
[PATCH 1/2] ocfs2: Add group extend for online resize
This patch adds the ability for a userspace program to request an extend of
last cluster group on an Ocfs2 file system. The request is made via ioctl,
OCFS2_IOC_GROUP_EXTEND. This is derived from EXT3_IOC_GROUP_EXTEND, but is
obviously Ocfs2 specific.
tunefs.ocfs2 would call this for an online-resize operation if the last
cluster group isn't full.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Hans de Goede [Sun, 20 Jan 2008 10:27:29 +0000 (11:27 +0100)]
[SCSI] usbstorage: use last_sector_bug flag universally
This patch sets the last_sector_bug flag to 1 for all USB disks. This is
needed to makes the cardreader on various HP multifunction printers work.
Since the performance impact is negible we set this flag for all USB disks to
avoid an unusual_devs.h nightmare.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tao Ma [Tue, 18 Dec 2007 07:46:37 +0000 (15:46 +0800)]
ocfs2: Reserve ioctl range
We need to reserve at least two ioctls for online-resize. Reserve a small
range of ioctls for Ocfs2 use in Documentation/ioctl-number.txt. This should
give us enough room for future growth.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Tao Ma [Tue, 18 Dec 2007 07:46:10 +0000 (15:46 +0800)]
ocfs2: Initalize bitmap_cpg of ocfs2_super to be the maximum.
This value is initialized from global_bitmap->id2.i_chain.cl_cpg. If there
is only 1 group, it will be equal to the total clusters in the volume. So
as for online resize, it should change for all the nodes in the cluster.
It isn't easy and there is no corresponding lock for it.
bitmap_cpg is only used in 2 areas:
1. Check whether the suballoc is too large for us to allocate from the global
bitmap, so it is little used. And now the suballoc size is 2048, it rarely
meet this situation and the check is almost useless.
2. Calculate which group a cluster belongs to. We use it during truncate to
figure out which cluster group an extent belongs too. But we should be OK
if we increase it though as the cluster group calculated shouldn't change
and we only ever have a small bitmap_cpg on file systems with a single
cluster group.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Herbert Xu [Fri, 25 Jan 2008 22:48:44 +0000 (09:48 +1100)]
[CRYPTO] hifn795x: Disallow built-in hifn795x when HW_RANDOM is m
Currently it is possible to select HW_RANDOM as a module and have
hifn795x built-in. This causes a build problem because hifn795x
will then call hwrng_register which isn't built-in.
This patch introduces a new config option to control the hifn795x
RNG which lets us avoid this problem.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Mark Fasheh [Tue, 30 Oct 2007 19:09:03 +0000 (12:09 -0700)]
ocfs2: Documentation update
Remove 'readpages' from the list in ocfs2.txt. Instead of having two
identical lists, I just removed the list in the OCFS2 section of fs/Kconfig
and added a pointer to Documentation/filesystems/ocfs2.txt.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mark Fasheh [Tue, 30 Oct 2007 19:08:32 +0000 (12:08 -0700)]
ocfs2: Readpages support
Add ->readpages support to Ocfs2. This is rather trivial - all it required
is a small update to ocfs2_get_block (for mapping full extents via b_size)
and an ocfs2_readpages() function which partially mirrors ocfs2_readpage().
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Joel Becker [Fri, 5 Oct 2007 21:31:44 +0000 (14:31 -0700)]
dlm: Split lock mode and flag constants into a sharable header.
This allows others to use the DLM constants without being tied to the
function API of fs/dlm.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mark Fasheh [Thu, 18 Oct 2007 22:23:46 +0000 (15:23 -0700)]
ocfs2: Remove data locks
The meta lock now covers both meta data and data, so this just removes the
now-redundant data lock.
Combining locks saves us a round of lock mastery per inode and one less lock
to ping between nodes during read/write.
We don't lose much - since meta locks were always held before a data lock
(and at the same level) ordered writeout mode (the default) ensured that
flushing for the meta data lock also pushed out data anyways.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mark Fasheh [Thu, 18 Oct 2007 22:13:59 +0000 (15:13 -0700)]
ocfs2: Add data downconvert worker to inode lock
In order to extend inode lock coverage to inode data, we use the same data
downconvert worker with only a small modification to only do work for
regular files.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mark Fasheh [Mon, 24 Sep 2007 22:56:19 +0000 (15:56 -0700)]
ocfs2: Remove mount/unmount votes
The node maps that are set/unset by these votes are no longer relevant, thus
we can remove the mount and umount votes. Since those are the last two
remaining votes, we can also remove the entire vote infrastructure.
The vote thread has been renamed to the downconvert thread, and the small
amount of functionality related to managing it has been moved into
fs/ocfs2/dlmglue.c. All references to votes have been removed or updated.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Linus Torvalds [Fri, 25 Jan 2008 22:41:24 +0000 (14:41 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (81 commits)
RDMA/cxgb3: Fix the T3A workaround checks
IB/ipath: Remove unnecessary cast
IPoIB: Constify seq_operations function pointer tables
RDMA/cxgb3: Mark QP as privileged based on user capabilities
RDMA/cxgb3: Fix page shift calculation in build_phys_page_list()
RDMA/cxgb3: Flush the receive queue when closing
IB/ipath: Trivial simplification of ipath_make_ud_req()
IB/mthca: Update latest "native Arbel" firmware revision
IPoIB: Remove redundant check of netif_queue_stopped() in xmit handler
IB/ipath: Add mappings from HW register to PortInfo port physical state
IB/ipath: Changes to support PIO bandwidth check on IBA7220
IB/ipath: Minor cleanup of unused fields and chip-specific errors
IB/ipath: New sysfs entries to control 7220 features
IB/ipath: Add new chip-specific functions to older chips, consistent init
IB/ipath: Remove unused MDIO interface code
IB/ehca: Prevent RDMA-related connection failures on some eHCA2 hardware
IB/ehca: Add "port connection autodetect mode"
IB/ehca: Define array to store SMI/GSI QPs
IB/ehca: Remove CQ-QP-link before destroying QP in error path of create_qp()
IB/iser: Add change_queue_depth method
...
Mark Fasheh [Mon, 24 Sep 2007 22:09:41 +0000 (15:09 -0700)]
ocfs2: Remove fs dependency on ocfs2_heartbeat module
Now that the dlm exposes domain information to us, we don't need generic
node up / node down callbacks. And since the DLM is only telling us when a
node goes down unexpectedly, we no longer need to optimize away node down
callbacks via the umount map.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mark Fasheh [Fri, 7 Sep 2007 18:11:10 +0000 (11:11 -0700)]
ocfs2_dlm: Call node eviction callbacks from heartbeat handler
With this, a dlm client can take advantage of the group protocol in the dlm
to get full notification whenever a node within the dlm domain leaves
unexpectedly.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The shift calculation must also take into account the address of the
first entry masked by the page_mask as well as the last address+size
rounded up to the next page size.
Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Steve Wise [Mon, 21 Jan 2008 20:42:09 +0000 (14:42 -0600)]
RDMA/cxgb3: Flush the receive queue when closing
- for kernel mode cqs, call event notification handler when flushing.
- flush QP when moving from RTS -> CLOSING.
- fix logic to identify a kernel mode qp.
Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Krishna Kumar [Thu, 15 Nov 2007 05:05:37 +0000 (10:35 +0530)]
IPoIB: Remove redundant check of netif_queue_stopped() in xmit handler
qdisc_run() now tests for queue_stopped() before calling
__qdisc_run(), and the same check is done in every iteration of
__qdisc_run(), so another check is not required in the driver xmit.
This means that ipoib_start_xmit() no longer needs to test
netif_queue_stopped(); the test was added to fix earlier kernels,
where the networking stack did not guarantee that the xmit method of
an LLTX driver would not be called after the queue was stopped, but
current kernels do provide this guarantee.
To validate, I put a debug in the TX_BUSY path which never hit with 64
threads running overnight exercising this code a few 100 million
times.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Michael Albaugh [Tue, 8 Jan 2008 08:37:34 +0000 (00:37 -0800)]
IB/ipath: New sysfs entries to control 7220 features
IBA7220 includes many more configurable IB settings. Getting/setting
these is now grouped into a pair of chip specific functions accessed via
function pointers. Provide sysfs access to these settings.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Dave Olson [Tue, 8 Jan 2008 10:36:46 +0000 (02:36 -0800)]
IB/ipath: Add new chip-specific functions to older chips, consistent init
This adds the new (sometimes empty) chip-specific functions to the older
chips, and makes the initialization and related functions consistent across
all 3 chips.
Signed-off-by: Dave Olson <dave.olson@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Joachim Fenkes [Thu, 17 Jan 2008 14:07:24 +0000 (15:07 +0100)]
IB/ehca: Prevent RDMA-related connection failures on some eHCA2 hardware
Some HW revisions of eHCA2 may cause an RC connection to break if they
received RDMA Reads over that connection before. This can be
prevented by assuring that, after the first RDMA Read, the QP receives
a new RDMA Read every few million link packets.
Include code into the driver that inserts an empty (size 0) RDMA Read
into the message stream every now and then if the consumer doesn't
post them frequently enough.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Hoang-Nam Nguyen [Thu, 17 Jan 2008 14:05:45 +0000 (15:05 +0100)]
IB/ehca: Add "port connection autodetect mode"
This patch enhances ehca with a capability to "autodetect" the ports
being connected physically. In order to utilize that function the
module option nr_ports must be set to -1 (default is 2 - two
ports). This feature is experimental and will made the default later.
More detail:
If the user connects only one port to the switch, current code requires
1) port one to be connected and
2) module option nr_ports=1 to be given.
If autodetect is enabled, ehca will not wait at creation of the GSI QP
for the respective port to become active. Since firmware does not
accept modify_qp() while the port is down at initialization, we need
to cache all calls to modify_qp() for the SMI/GSI QP and just return a
good return code.
When a port is activated and we get a PORT_ACTIVE event, we replay the
cached modify-qp() parms and re-trigger any posted recv WRs. Only then
do we forward the PORT_ACTIVE event to registered clients.
The result of this autodetect patch is that all ports will be
accessible by the users. Depending on their respective cabling only
those ports that are connected properly will become operable. If a
user tries to modify a regular QP of a non-connected port, modify_qp()
will fail. Furthermore, ibv_devinfo should show the port state
accordingly.
Note that this patch primarily improves the loading behaviour of
ehca. If the cable is removed while the driver is operating and
plugged in again, firmware will handle that properly by sending an
appropriate async event.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>