Nicolas Pitre [Thu, 8 Nov 2012 18:46:07 +0000 (19:46 +0100)]
ARM: 7573/1: idmap: use flush_cache_louis() and flush TLBs only when necessary
Flushing the cache is needed for the hardware to see the idmap table
and therefore can be done at init time. On ARMv7 it is not necessary to
flush L2 so flush_cache_louis() is used here instead.
There is no point flushing the cache in setup_mm_for_reboot() as the
caller should, and already is, taking care of this. If switching the
memory map requires a cache flush, then cpu_switch_mm() already includes
that operation.
What is not done by cpu_switch_mm() on ASID capable CPUs is TLB flushing
as the whole point of the ASID is to tag the TLBs and avoid flushing them
on a context switch. Since we don't have a clean ASID for the identity
mapping, we need to flush the TLB explicitly in that case. Otherwise
this is already performed by cpu_switch_mm().
Signed-off-by: Nicolas Pitre <nico@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Josh Cartwright [Sun, 4 Nov 2012 21:03:02 +0000 (22:03 +0100)]
ARM: 7570/1: quiet down the non make -s output
Commit edc88ceb0c7d285b9f58bc29a638cd8163b59989 silenced the make -s build, but
inadvertently made louder the non-silent build. Fix by prepending '@' to each
of the added $(kecho) statements.
CHK include/generated/compile.h
echo ' Kernel: arch/arm/boot/Image is ready'
Kernel: arch/arm/boot/Image is ready
LD arch/arm/boot/compressed/vmlinux
OBJCOPY arch/arm/boot/zImage
echo ' Kernel: arch/arm/boot/zImage is ready'
Kernel: arch/arm/boot/zImage is ready
Build with this fix:
CHK include/generated/compile.h
Kernel: arch/arm/boot/Image is ready
LD arch/arm/boot/compressed/vmlinux
OBJCOPY arch/arm/boot/zImage
Kernel: arch/arm/boot/zImage is ready
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 8 Nov 2012 10:51:03 +0000 (10:51 +0000)]
WATCHDOG: fix build PM warnings
drivers/watchdog/sp805_wdt.c:288:12: warning: 'sp805_wdt_suspend' defined but not used
drivers/watchdog/sp805_wdt.c:298:12: warning: 'sp805_wdt_resume' defined but not used
This is caused by the wrong config symbol being used for these functions.
Rather than fixing that, mark the functions with __maybe_unused
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Gregory CLEMENT [Tue, 6 Nov 2012 00:58:07 +0000 (01:58 +0100)]
ARM: 7547/4: cache-l2x0: add support for Aurora L2 cache ctrl
Aurora Cache Controller was designed to be compatible with the ARM L2
Cache Controller. It comes with some difference or improvement such
as:
- no cache id part number available through hardware (need to get it
by the DT).
- always write through mode available.
- two flavors of the controller outer cache and system cache (meaning
maintenance operations on L1 are broadcasted to the L2 and L2
performs the same operation).
- in outer cache mode, the cache maintenance operations are improved and
can be done on a range inside a page and are not limited to a cache
line.
Tested-and-Reviewed-by: Lior Amsalem <alior@marvell.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Yehuda Yitschak <yehuday@marvell.com> Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 12:32:08 +0000 (13:32 +0100)]
SERIAL: omap: fix hardware assisted flow control
When the UART device has hardware flow control enabled, it ignores the
MCR RTS bit in the MCR register, and keeps RTS asserted as long as we
continue to read characters from the UART receiver FIFO. This means
that when the TTY buffers become full, the UART doesn't tell the remote
end to stop sending, which causes the TTY layer to start dropping
characters.
A similar problem exists with software flow control. We need the FIFO
register to fill when software flow control is enabled to provoke the
UART to send the XOFF character.
Fix this by implementing the throttle/unthrottle callbacks, and use
these to disable receiver interrupts. This in turn means that the UART
FIFO will fill, which will then cause the UART's hardware to deassert
the RTS signal and/or send the XOFF character, stopping the remote end.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 6 Oct 2012 08:34:36 +0000 (09:34 +0100)]
SERIAL: omap: move xon/xoff setting earlier
Take advantage of the switch to mode B for accessing the TCR register,
and move the xon/xoff configuration there. This allows further
simplication of this sequence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 6 Oct 2012 08:12:44 +0000 (09:12 +0100)]
SERIAL: omap: always set TCR
We always setup the TCR register in the software flow control path,
and when hardware flow control is enabled. Remove this redundant
setup, and place it before we setup any hardware flow control.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 6 Oct 2012 08:08:20 +0000 (09:08 +0100)]
SERIAL: omap: simplify
We have the sequence:
- LCR mode B
- write EFR with ECB clear
- LCR mode normal
- if s/w flow
- LCR mode B
- write EFR with ECB clear
...
- LCR mode B
- write EFR with ECB clear
- LCR mode normal
This can be simplified to:
- if s/w flow
- LCR mode B
- write EFR with ECB clear
...
- LCR mode B
- write EFR with ECB clear
- LCR mode normal
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 6 Oct 2012 08:04:03 +0000 (09:04 +0100)]
SERIAL: omap: don't read back LCR/MCR/EFR
There's really no reason to read back these registers while setting
the termios modes, provided we keep our cached copies up to date.
Remove these readbacks.
This has the benefit that we know that the EFR_ECB and MCR_TCRTLR
bits will always be clear, so we don't need to keep masking these
bits throughout the code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 6 Oct 2012 09:50:58 +0000 (10:50 +0100)]
SERIAL: omap: move driver private definitions and structures to driver
struct uart_omap_port and struct uart_omap_dma, and associated
definitions are private to the driver, so there's no point them sitting
in an include file under arch/arm. Move them into the driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 15 Oct 2012 14:21:46 +0000 (15:21 +0100)]
SERIAL: omap: remove 'irq_pending' bitfield
irq_pending is never used, so let's remove it. It seems to be result
of a bad rebase of d37c6cebcb0c (serial: omap: move uart_omap_port
definition to C file)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 12:54:53 +0000 (13:54 +0100)]
SERIAL: omap: fix MCR TCRTLR bit handling
The MCR TCRTLR bit can only be changed when ECB is set in the EFR.
Unfortunately, several places were trying to alter this bit while ECB
was clear:
- serial_omap_configure_xonxoff() was attempting to clear the bit after
explicitly clearing the ECB bit.
- serial_omap_set_termios() was trying the same trick after setting the
SCR, and when trying to change the TCR register when hardware flow
control was enabled.
Fix this by ensuring that we always have ECB set whenever the TCRTLR bit
is changed.
Moreover, we start out by reading the EFR and MCR registers, which may
have indeterminent bit settings for the ECB and TCRTLR bits. Ensure
that these bits always start off in a known state.
In order to avoid any undesired behaviour appearing through fixing this,
we also ensure that hardware assisted flow control is disabled while new
driver specific parts are not in place.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 11:23:28 +0000 (12:23 +0100)]
SERIAL: omap: fix set_mctrl() breakage
c538d20c7f (and maybe previous commits) broke set_mctrl() by making
it only capable of setting bits in the MCR register. This prevents
software controlled flow control and modem control line manipulation
via TIOCMSET/TIOCMBIC from working correctly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 14:13:56 +0000 (15:13 +0100)]
SERIAL: omap: no need to re-read EFR
There's no need to re-read EFR after we've recently written it; the
register is a configuration register which doesn't change its value
without us writing to it. The last value which was written to this
register was up->efr.
Removing this re-reading avoids the possibility that we end up with
up->efr having unintended bits set, which should only be temporarily
set when accessing the enhanced features.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 23:51:17 +0000 (00:51 +0100)]
SERIAL: omap: remove setting of EFR SCD bit
The SCD (special character detect) bit enables comparisons with XOFF2,
which we do not program. As the XOFF2 character remains unprogrammed,
there's little point enabling this feature along with its associated
interrupt. Remove this, and ensure that the SCD bit is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 23:11:16 +0000 (00:11 +0100)]
SERIAL: omap: allow hardware assisted IXANY mode to be disabled
Nothing was clearing the UART_MCR_XONANY bit, so once the ixany
mode gets set, there's no possibility to disable it. Clear this
bit when IXANY mode is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 22:48:28 +0000 (23:48 +0100)]
SERIAL: omap: allow hardware assisted rts/cts modes to be disabled
There is nothing which clears the auto RTS/CTS bits, so once hardware
flow control gets enabled, there's no possibility to disable it.
So, clear these bits when CRTSCTS is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 17 Apr 2012 16:23:14 +0000 (17:23 +0100)]
SERIAL: core: add throttle/unthrottle callbacks for hardware assisted flow control
Add two callbacks for hardware assisted flow control; we need to know
when the tty layers want us to stop and restart due to their buffer
levels.
Call a driver specific throttle/unthrottle function if and only if the
driver indicates that it is using an enabled hardware assisted flow
control method, otherwise fall back to the non-hardware assisted
methods.
Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 17 Apr 2012 15:41:10 +0000 (16:41 +0100)]
SERIAL: core: add hardware assisted h/w flow control support
Ports which are handling h/w flow control in hardware must not have
their RTS state altered depending on the tty's hardware-stopped state.
Avoid this additional logic when setting the termios state.
Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 17 Apr 2012 15:34:13 +0000 (16:34 +0100)]
SERIAL: core: add hardware assisted s/w flow control support
Ports which are capable of handling s/w flow control in hardware to
know when the s/w flow control termios settings are changed. Add a
flag to allow the low level serial drivers to indicate that they
support this, and these changes should be propagated to them.
Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The variables here are really not used uninitialized.
arch/arm/mm/alignment.c: In function 'do_alignment':
arch/arm/mm/alignment.c:327:15: warning: 'offset.un' may be used uninitialized in this function [-Wmaybe-uninitialized]
arch/arm/mm/alignment.c:748:21: note: 'offset.un' was declared here
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stephen Boyd [Mon, 29 Oct 2012 18:19:34 +0000 (19:19 +0100)]
ARM: 7568/1: Sort exception table at compile time
Add the ARM machine identifier to sortextable and select the
config option so that we can sort the exception table at compile
time. sortextable relies on a section named __ex_table existing
in the vmlinux, but ARM's linker script places the exception
table in the data section. Give the exception table its own
section so that sortextable can find it.
This allows us to skip the sorting step during boot.
Cc: David Daney <david.daney@cavium.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Tested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Tue, 23 Oct 2012 07:29:48 +0000 (08:29 +0100)]
ARM: 7563/1: SMP_TWD: make setup()/stop() reentrant
It has been brought to my knowledge that the .setup()/.stop()
function pair in the SMP TWD is going to be called from atomic
contexts for CPUs coming and going, and then the
clk_prepare()/clk_unprepare() calls cannot be called
on subsequent .setup()/.stop() iterations. This is however
just the tip of an iceberg as the function pair is not
designed to be reentrant at all.
This change makes the SMP_TWD clock .setup()/.stop() pair reentrant
by splitting the .setup() function in three parts:
- One COMMON part that is executed the first time the first CPU
in the TWD cluster is initialized. This will fetch the TWD
clk for the cluster and prepare+enable it. If no clk is
available it will calibrate the rate instead.
- One part that is executed the FIRST TIME a certain CPU is
brought on-line. This initializes and sets up the clock event
for a certain CPU.
- One part that is executed on every subsequent .setup() call.
This will re-initialize the clock event. This is augmented
to call the clk_enable()/clk_disable() pair properly.
Cc: Shawn Guo <shawn.guo@linaro.org> Reported-by: Peter Chen <peter.chen@freescale.com> Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Sat, 3 Nov 2012 22:27:21 +0000 (15:27 -0700)]
Merge tag 'nfs-for-3.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix a bunch of deadlock situations:
* State recovery can deadlock if we fail to release sequence ids
before scheduling the recovery thread.
* Calling deactivate_super() from an RPC workqueue thread can
deadlock because of the call to rpc_shutdown_client.
- Display the device name correctly in /proc/*/mounts
- Fix a number of incorrect error return values:
* When NFSv3 mounts fail due to a timeout.
* On NFSv4.1 backchannel setup failure
* On NFSv4 open access checks
- pnfs_find_alloc_layout() must check the layout pointer for NULL
- Fix a regression in the legacy DNS resolved
* tag 'nfs-for-3.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS4: nfs4_opendata_access should return errno
NFSv4: Initialise the NFSv4.1 slot table highest_used_slotid correctly
SUNRPC: return proper errno from backchannel_rqst
NFS: add nfs_sb_deactive_async to avoid deadlock
nfs: Show original device name verbatim in /proc/*/mount{s,info}
nfsv3: Make v3 mounts fail with ETIMEDOUTs instead EIO on mountd timeouts
nfs: Check whether a layout pointer is NULL before free it
NFS: fix bug in legacy DNS resolver.
NFSv4: nfs4_locku_done must release the sequence id
NFSv4.1: We must release the sequence id when we fail to get a session slot
NFS: Wait for session recovery to finish before returning
Linus Torvalds [Sat, 3 Nov 2012 22:25:14 +0000 (15:25 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management & ACPI update from Zhang Rui,
Ho humm. Normally these things go through Len. But it's just three
small fixes, I guess I can pull directly too.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
exynos4_tmu_driver_ids should be exynos_tmu_driver_ids.
ACPI video: Ignore errors after _DOD evaluation.
thermal: solve compilation errors in rcar_thermal
Linus Torvalds [Sat, 3 Nov 2012 22:14:54 +0000 (15:14 -0700)]
Merge branch 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux
Pull i2c embedded fixes from Wolfram Sang:
"Two patches are usual stuff.
The bigger patch is needed to correct a wrong decision made in this
merge window. We hoped to get the PIOQUEUE mode in the mxs driver
working with DMA, but it turned out to be too broken (leading to data
loss), so we now think it is best to remove it entirely and work only
with DMA now. The patch should be in 3.7. IMO, so users never get
the chance to use both modes in parallel."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: tegra: set irq name as device name
i2c-nomadik: Fixup clock handling
i2c: mxs: remove broken PIOQUEUE support
it's slightly bigger than I'd probably like, but nothing looked
dangerous enough to hold off on."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/udl: fix stride issues scanning out stride != width*bpp
drm/radeon: add load detection support for ext DAC on R200 (v2)
DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
DRM/Radeon: Clean up code in TV DAC load detection.
drm/radeon: fix ATPX function documentation
drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
DRM/Radeon: Fix Load Detection on legacy primary DAC.
drm: exynos: removed warning due to missing typecast for mixer driver data
drm/exynos: add support for ARCH_MULTIPLATFORM
MAINTAINERS: Add git repository for Exynos DRM
drm/exynos: fix display on issue
drm/i915: Only kick out vesafb if we takeover the fbcon with KMS
drm/i915: be less verbose about inability to provide vendor backlight
drm/i915: clear the entire sdvo infoframe buffer
drm/i915: VGA needs to be on pipe A on i830M
drm/i915: fix overlay on i830M
Pull networking fixes from David Miller:
"First post-Sandy pull request"
1) Fix antenna gain handling and initialization of chan->max_reg_power
in wireless, from Felix Fietkau.
2) Fix nexthop handling in H.232 conntrack helper, from Julian
Anastasov.
3) Only process 80211 mesh config header in certain kinds of frames,
from Javier Cardona.
4) 80211 management frame header length needs to be validated, from
Johannes Berg.
5) Don't access free'd SKBs in ath9k driver, from Felix Fietkay.
6) Test for permanent state correctly in VXLAN driver, from Stephen
Hemminger.
7) BNX2X bug fixes from Yaniv Rosner and Dmitry Kravkov.
8) Fix off by one errors in bonding, from Nikolay ALeksandrov.
9) Fix divide by zero in TCP-Illinois congestion control. From Jesper
Dangaard Brouer.
10) TCP metrics code says "Yo dawg, I heard you like sizeof, so I did a
sizeof of a sizeof, so you can size your size" Fix from Julian
Anastasov.
11) Several drivers do mdiobus_free without first doing an
mdiobus_unregister leading to stray pointer references. Fix from
Peter Senna Tschudin.
12) Fix OOPS in l2tp_eth_create() error path, it's another danling
pointer kinda situation. Fix from Tom Parkin.
13) Hardware driven by the vmxnet driver can't handle larger than 16K
fragments, so split them up when necessary. From Eric Dumazet.
14) Handle zero length data length in tcp_send_rcvq() properly. Fix
from Pavel Emelyanov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tcp-repair: Handle zero-length data put in rcv queue
vmxnet3: must split too big fragments
l2tp: fix oops in l2tp_eth_create() error path
cxgb4: Fix unable to get UP event from the LLD
drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free
drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free
bnx2x: fix HW initialization using fw 7.8.x
tcp: Fix double sizeof in new tcp_metrics code
net: fix divide by zero in tcp algorithm illinois
net: sctp: Fix typo in net/sctp
bonding: fix second off-by-one error
bonding: fix off-by-one error
bnx2x: Disable FCoE for 57840 since not yet supported by FW
bnx2x: Fix no link on 577xx 10G-baseT
bnx2x: Fix unrecognized SFP+ module after driver is loaded
bnx2x: Fix potential incorrect link speed provision
bnx2x: Restore global registers back to default.
bnx2x: Fix link down in 57712 following LFA
bnx2x: Fix 57810 1G-KR link against certain switches.
ixgbe: PTP get_ts_info missing software support
...
Pavel Emelyanov [Mon, 29 Oct 2012 05:05:33 +0000 (05:05 +0000)]
tcp-repair: Handle zero-length data put in rcv queue
When sending data into a tcp socket in repair state we should check
for the amount of data being 0 explicitly. Otherwise we'll have an skb
with seq == end_seq in rcv queue, but tcp doesn't expect this to happen
(in particular a warn_on in tcp_recvmsg shoots).
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Reported-by: Giorgos Mavrikas <gmavrikas@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Parkin [Mon, 29 Oct 2012 23:41:48 +0000 (23:41 +0000)]
l2tp: fix oops in l2tp_eth_create() error path
When creating an L2TPv3 Ethernet session, if register_netdev() should fail for
any reason (for example, automatic naming for "l2tpeth%d" interfaces hits the
32k-interface limit), the netdev is freed in the error path. However, the
l2tp_eth_sess structure's dev pointer is left uncleared, and this results in
l2tp_eth_delete() then attempting to unregister the same netdev later in the
session teardown. This results in an oops.
To avoid this, clear the session dev pointer in the error path.
Signed-off-by: Tom Parkin <tparkin@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Murzov [Sat, 13 Oct 2012 00:41:25 +0000 (04:41 +0400)]
ACPI video: Ignore errors after _DOD evaluation.
There are systems where video module known to work fine regardless
of broken _DOD and ignoring returned value here doesn't cause
any issues later. This should fix brightness controls on some laptops.
Devendra Naga [Wed, 31 Oct 2012 08:46:10 +0000 (17:46 +0900)]
thermal: solve compilation errors in rcar_thermal
following were the errors reported
drivers/thermal/rcar_thermal.c: In function ‘rcar_thermal_probe’:
drivers/thermal/rcar_thermal.c:214:10: warning: passing argument 3 of ‘thermal_zone_device_register’ makes integer from pointer without a cast [enabled by default]
include/linux/thermal.h:166:29: note: expected ‘int’ but argument is of type ‘struct rcar_thermal_priv *’
drivers/thermal/rcar_thermal.c:214:10: error: too few arguments to function ‘thermal_zone_device_register’
include/linux/thermal.h:166:29: note: declared here
make[1]: *** [drivers/thermal/rcar_thermal.o] Error 1
make: *** [drivers/thermal/rcar_thermal.o] Error 2
with gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5)
Vipul Pandya [Mon, 29 Oct 2012 02:02:36 +0000 (02:02 +0000)]
cxgb4: Fix unable to get UP event from the LLD
If T4 configuration file gets loaded from the /lib/firmware/cxgb4/ directory
then offload capabilities of the cards were getting disabled during
initialization. Hence ULDs do not get an UP event from the LLD.
Signed-off-by: Jay Hernandez <jay@chelsio.com> Signed-off-by: Vipul Pandya <vipul@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Tested-by: Roland Stigge <stigge@antcom.de> Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 28 Oct 2012 21:59:04 +0000 (21:59 +0000)]
bnx2x: fix HW initialization using fw 7.8.x
Since commit 96bed4b9 (use FW 7.8.2) BRB HW block needs to be
initialized using fw values for all devices.
Otherwise ETS on 57712/578xx will not work.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more scsi target fixes from Nicholas Bellinger:
"This series is a second round of target fixes for v3.7-rc4 that have
come into target-devel over the last days, and are important enough to
be applied ASAP.
All are being CC'ed to stable. The most important two are:
- target: Re-add explict zeroing of INQUIRY bounce buffer memory to
fix a regression for handling zero-length payloads, a bug that went
during v3.7-rc1, and hit >= v3.6.3 stable. (nab + paolo)
- iscsi-target: Fix a long-standing missed R2T wakeup race in TX
thread processing when using a single queue slot. (Roland)
Thanks to Roland & PureStorage team for helping to track down this
long standing race with iscsi-target single queue slot operation.
Also, the tcm_fc(FCoE) regression bug that was observed recently with
-rc2 code has also been resolved with the cancel_delayed_work() return
bugfix (commit c0158ca64da5: "workqueue: cancel_delayed_work() should
return %false if work item is idle") now in -rc3. Thanks again to Yi
Zou, MDR, Robert Love @ Intel for helping to track this down."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix incorrect usage of nested IRQ spinlocks in ABORT_TASK path
iscsi-target: Fix missed wakeup race in TX thread
target: Avoid integer overflow in se_dev_align_max_sectors()
target: Don't return success from module_init() if setup fails
target: Re-add explict zeroing of INQUIRY bounce buffer memory
Linus Torvalds [Fri, 2 Nov 2012 20:27:52 +0000 (13:27 -0700)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"An e-mail address update, and fix a compile error on SPARC"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Only include of_match_table with CONFIG_OF_GPIO
hwmon, fam15h_power: Change email address, MAINTAINERS entry
Linus Torvalds [Fri, 2 Nov 2012 20:27:01 +0000 (13:27 -0700)]
Merge tag 'frv-fixes-20121102' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-frv
Pull FRV fixes from David Howells:
"A collection of small fixes for the FRV architecture."
* tag 'frv-fixes-20121102' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-frv:
frv: fix the broken preempt
frv: switch to saner kernel_execve() semantics
FRV: Fix the new-style kernel_thread() stuff
FRV: Fix the preemption handling
FRV: gcc-4.1.2 also inlines weak functions
FRV: Don't objcopy the GNU build_id note
FRV: Add missing linux/export.h #inclusions
Linus Torvalds [Fri, 2 Nov 2012 20:26:11 +0000 (13:26 -0700)]
Merge tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Use appropriate macros instead of hand-rolling our own (ARM).
- Fixes if FB/KBD closed unexpectedly.
- Fix memory leak in /dev/gntdev ioctl calls.
- Fix overflow check in xenbus_file_write.
- Document cleanup.
- Performance optimization when migrating guests.
* tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/mmu: Use Xen specific TLB flush instead of the generic one.
xen/arm: use the __HVC macro
xen/xenbus: fix overflow check in xenbus_file_write()
xen-kbdfront: handle backend CLOSED without CLOSING
xen-fbfront: handle backend CLOSED without CLOSING
xen/gntdev: don't leak memory from IOCTL_GNTDEV_MAP_GRANT_REF
x86: remove obsolete comment from asm/xen/hypervisor.h
Sasha Levin [Tue, 30 Oct 2012 18:45:57 +0000 (14:45 -0400)]
hashtable: introduce a small and naive hashtable
This hashtable implementation is using hlist buckets to provide a simple
hashtable to prevent it from getting reimplemented all over the kernel.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
[ Merging this now, so that subsystems can start applying Sasha's
patches that use this - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Fri, 2 Nov 2012 16:05:44 +0000 (12:05 -0400)]
frv: fix the broken preempt
Just get %icc2 into the state we would have after local_irq_disable()
and physical IRQ having happened since then. Then we can simply
use preempt_schedule_irq() and be done with the whole mess.
Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David Howells [Fri, 2 Nov 2012 13:20:43 +0000 (13:20 +0000)]
FRV: Fix the new-style kernel_thread() stuff
The kernel_thread() changes for FRV don't work, and FRV fails to boot,
starting with:
commit 02ce496f152df87be081a64796498942c433a2fd
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Tue Sep 18 22:18:51 2012 -0400
Subject: frv: split ret_from_fork, simplify kernel_thread() a lot
The problem is that the userspace registers are completely cleared when a
kernel thread is created and all subsequent user threads are then copied from
that. Unfortunately, however, the TBR and PSR registers are restored from the
pt_regs and the values they should be set to are clobbered by the memset.
Instead, copy across the old user registers as normal, and then merely alter
GR8 and GR9 in it if we're going to execute a kernel thread.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 2 Nov 2012 13:20:42 +0000 (13:20 +0000)]
FRV: Fix the preemption handling
Fix the preemption handling in FRV code where the PREEMPT_ACTIVE value is
incorrectly loaded into the threadinfo flags rather than the threadinfo
preemption count.
Unfortunately, the code cannot be simply converted to use
preempt_schedule_irq() as is because FRV uses virtual interrupt disablement to
cut down on the cost of actually disabling interrupts and thus
local_irq_enable() doesn't actually enable interrupts.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Al Viro <viro@ZenIV.linux.org.uk>
Wolfram Sang [Fri, 12 Oct 2012 10:55:16 +0000 (11:55 +0100)]
i2c: mxs: remove broken PIOQUEUE support
This I2C master can do DMA and PIOQUEUE (PIO with FIFO). Originally,
only PIOQUEUE was supported and it had issues, then DMA support was added
this cycle. The original intention was to keep PIOQUEUE since it has
less overhead what is nice for small transfers. However, runtime
switching between PIOQEUE and DMA depending on the transfer size never
worked despite a lot of trying. Since PIOQUEUE mode itself was flaky
(polling at places where interrupts failed to work) and the
implementation also imposed a size limit for transfers, it is best to
remove the support, so users don't fall over its limitations. It also
makes the driver a lot cleaner and more robust. If somebody really wants
less overhead, plain PIO mode could still be implemented with the
addidtional advantage that this mode is also available on MX23, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de>
Linus Torvalds [Fri, 2 Nov 2012 00:48:19 +0000 (17:48 -0700)]
Merge tag 'xtensa-next-20121101' of git://github.com/czankel/xtensa-linux
Pull Xtensa fixes from Chris Zankel:
"Some important bug fixes.
With the change to uapi, there was a bug introduced that results in an
empty syscall table (mult-inclusion bug). Switching to the generic
thread/execve allowed us to fix a bug we had in vfork()."
* tag 'xtensa-next-20121101' of git://github.com/czankel/xtensa-linux:
xtensa: switch to generic sys_execve()
xtensa: switch to generic kernel_execve()
xtensa: switch to generic kernel_thread()
xtensa: reset windowbase/windowstart when cloning the VM
xtensa: use physical addresses for bus addresses
xtensa: allow multi-inclusion for uapi/unistd.h
Dave Airlie [Thu, 1 Nov 2012 03:47:09 +0000 (13:47 +1000)]
drm/udl: fix stride issues scanning out stride != width*bpp
When buffer sharing with the i915 and using a 1680x1050 monitor,
the i915 gives is a 6912 buffer for the 6720 width, the code doesn't
render this properly as it uses one value to set the base address for
reading from the vmap and for where to start on the device.
This fixes it by calculating the values correctly for the device and
for the pixmap. No idea how I haven't seen this before now.
Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Jamie Lentin [Thu, 1 Nov 2012 23:55:43 +0000 (23:55 +0000)]
hwmon: Only include of_match_table with CONFIG_OF_GPIO
The following fixes build errors on sparc. Without any DT support,
of_match_ptr is NULL and the below is a no-op. However, if just
CONFIG_OF is defined then so is of_match_ptr.
All useful parts of the gpio-fan DT support rely on CONFIG_OF_GPIO
anyway, so of_match_table should too.
Dave Airlie [Fri, 2 Nov 2012 00:30:37 +0000 (10:30 +1000)]
Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Inki writes:
"As I posted before, we have added a new git repository for Exynos drm
to MAINTAINERS file so change it to new one like below,
from git://git.infradead.org/users/kmpark/linux-samsung
to git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos
And this pull request includes the following:
- fix display on issue when user requested dpms mode changing.
- add git repository for Exynos drm to MAINTAINERS file.
- add support for ARCH_MULTIPLATFORM.
- and code clean."
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm: exynos: removed warning due to missing typecast for mixer driver data
drm/exynos: add support for ARCH_MULTIPLATFORM
MAINTAINERS: Add git repository for Exynos DRM
drm/exynos: fix display on issue
Dave Airlie [Fri, 2 Nov 2012 00:29:22 +0000 (10:29 +1000)]
Merge branch 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex writes:
"This request is mostly load detection fixes from Egbert and me."
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add load detection support for ext DAC on R200 (v2)
DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
DRM/Radeon: Clean up code in TV DAC load detection.
drm/radeon: fix ATPX function documentation
drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
DRM/Radeon: Fix Load Detection on legacy primary DAC.
Dave Airlie [Fri, 2 Nov 2012 00:26:03 +0000 (10:26 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel Vetter writes"
Nothing big at all for -fixes, just small stuff:
- Two patches to fix bugs on i830M
- ums regression fixer due to kicking firmeware fbs (Chris)
- tune down a too loud warning (Jani)
- be more careful with sdvo infoframes, which fixes a long-standing
sdvo-hdmi regression"
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Only kick out vesafb if we takeover the fbcon with KMS
drm/i915: be less verbose about inability to provide vendor backlight
drm/i915: clear the entire sdvo infoframe buffer
drm/i915: VGA needs to be on pipe A on i830M
drm/i915: fix overlay on i830M
Reading TCP stats when using TCP Illinois congestion control algorithm
can cause a divide by zero kernel oops.
The division by zero occur in tcp_illinois_info() at:
do_div(t, ca->cnt_rtt);
where ca->cnt_rtt can become zero (when rtt_reset is called)
Steps to Reproduce:
1. Register tcp_illinois:
# sysctl -w net.ipv4.tcp_congestion_control=illinois
2. Monitor internal TCP information via command "ss -i"
# watch -d ss -i
3. Establish new TCP conn to machine
Either it fails at the initial conn, or else it needs to wait
for a loss or a reset.
This is only related to reading stats. The function avg_delay() also
performs the same divide, but is guarded with a (ca->cnt_rtt > 0) at its
calling point in update_params(). Thus, simply fix tcp_illinois_info().
Function tcp_illinois_info() / get_info() is called without
socket lock. Thus, eliminate any race condition on ca->cnt_rtt
by using a local stack variable. Simply reuse info.tcpv_rttcnt,
as its already set to ca->cnt_rtt.
Function avg_delay() is not affected by this race condition, as
its called with the socket lock.
Cc: Petr Matousek <pmatouse@redhat.com> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Masanari Iida [Wed, 31 Oct 2012 05:48:19 +0000 (05:48 +0000)]
net: sctp: Fix typo in net/sctp
Correct spelling typo in net/sctp/socket.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.
How to reproduce:
with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/active_slave;
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Note: Sorry for the second patch but I missed this one while checking
the file. You can squash them into one patch. Signed-off-by: David S. Miller <davem@davemloft.net>
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.
How to reproduce:
with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/primary;
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 31 Oct 2012 05:46:57 +0000 (05:46 +0000)]
bnx2x: Fix no link on 577xx 10G-baseT
Since the Warpcore supports various link types, need to set only the correct
supported modes for XFI which is the serdes interface for the 10G-baseT PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 31 Oct 2012 05:46:56 +0000 (05:46 +0000)]
bnx2x: Fix unrecognized SFP+ module after driver is loaded
When SFP+ module is plugged in after driver is already loaded, it may not be
recognized, so set SFP module recognition time up to 300ms, without resetting
the module power in the middle.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 31 Oct 2012 05:46:55 +0000 (05:46 +0000)]
bnx2x: Fix potential incorrect link speed provision
Fix possible incorrect link speed provision following rapid link speed change.
Clear link speed mask after each link change, and not only after link down.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 31 Oct 2012 05:46:54 +0000 (05:46 +0000)]
bnx2x: Restore global registers back to default.
Several KR registers were not set correctly back to default after
loopback test, so set those global registers over the global WC lane (zero)
rather than the current lane.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Wed, 31 Oct 2012 22:30:54 +0000 (22:30 +0000)]
ixgbe: PTP get_ts_info missing software support
This patch corrects the ethtool get_ts_info functon which did not state that
software timestamping was supported, even though it is.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> CC: Stable <stable@vger.kernel.org> [3.5] Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Deucher [Wed, 31 Oct 2012 15:51:03 +0000 (11:51 -0400)]
drm/radeon: add load detection support for ext DAC on R200 (v2)
The R200 asics use an external DAC for the secondary DAC.
The current KMS code tries to use code for the integrated
TV DAC for R200 which leads to unpredictable results since
R200 does not have an integrated TV DAC. This patch ports
the external DAC load detection support from the UMS
driver to KMS.
v2: fix typo in loop break logic
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Egbert Eich <eich@suse.de>
Egbert Eich [Mon, 29 Oct 2012 12:46:48 +0000 (13:46 +0100)]
DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
On all dual CRTC GPUs the CRTC_CRT_ON in the RADEON_CRTC_EXT_CNTL register
controls the CRTC of the primary DAC. Therefore it is set in the DAC DMPS
function.
This is different for GPU's with a single CRTC but a primary and a
TV DAC: here it controls the single CRTC no matter where it is routed.
Therefore we set it here. This avoids an elaborate on/off state tracking
since both primary_dac_dpms() and tv_dac_dpms() functions would have
to touch this bit.
On single CRTC GPUs with just one DAC it's irrelevant where this bit
is handled.
agd5f: fix warning
Signed-off-by: Egbert Eich <eich@suse.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Egbert Eich [Wed, 24 Oct 2012 16:32:52 +0000 (18:32 +0200)]
DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
The Radeon driver uses the analog/digital flag to determine if the
DAC or the TMDS encoder should be enabled on a DVI-I connector.
If the EDID is bogus this flag is no longer reliable. This fix
adds a fallback to DAC load detection to determine if anything
is connected to the DAC. If not and a (bogus) EDID is found it
assumes a digital display is connected.
This works around problems with some crappy IPMI devices using
Radeon ES1000.
Signed-off-by: Egbert Eich <eich@suse.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Egbert Eich [Wed, 24 Oct 2012 16:31:19 +0000 (18:31 +0200)]
DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
For Radeon 7500 ATI recommends a DAC_FORCE value of 0x1ac. This value
works better on ES1000 (RV100) chips, too, as it doesn't produce any false
positives on any cards I have tested. Therefore let's assume that this
value is good for all RV100 and RV200 chipset generations.
Signed-off-by: Egbert Eich <eich@suse.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / karo-tx-linux.git / log