Thomas Pedersen [Sun, 27 Jan 2013 00:39:55 +0000 (16:39 -0800)]
mac80211: dynamic short slot time for MBSSs
The standard mandates mesh STAs to set the ERP Short Slot
Time capability info bit in beacons to 0. Even though this
is their way of disallowing short slot time for mesh STAs,
there should be no harm in enabling it if we determine all
STAs in the current MBSS support ERP rates.
Increases throughput about 20% for legacy rates when
enabled.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Sat, 26 Jan 2013 21:16:08 +0000 (22:16 +0100)]
cfg80211: add SME state to warning in __cfg80211_mlme_disassoc
The warning here occasionally triggers but we haven't
found the cause yet. It's a valid warning since if it
triggers the SME state got confused, so add the SME
state to it to help narrow it down in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before "mac80211: clean up mesh sta allocation warning"
was applied, mesh_sta_info_get() was reshuffled to please
sparse. As a result we neglect to initialize newly created
STAs. Fix this.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add API to enable drivers to implement MAC address based
access control in AP/P2P GO mode. Capable drivers advertise
this capability by setting the maximum number of MAC
addresses in such a list in wiphy->max_acl_mac_addrs.
An initial ACL may be given to the NL80211_CMD_START_AP
command and/or changed later with NL80211_CMD_SET_MAC_ACL.
Black- and whitelists are supported, but not simultaneously.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
[rewrite commit log, many cleanups] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arnd Bergmann [Fri, 25 Jan 2013 14:14:33 +0000 (14:14 +0000)]
mac80211: avoid a build warning
gcc cannot prove that the value of sdata->vif.type does not
change between the switch() statement and the second
comparison to NL80211_IFTYPE_AP, causing a harmless
warning.
Slightly reordering the code makes the warning go away
with no functional change.
Without this patch, building ARM at91sam9g45_defconfig with
gcc-4.6 results in:
net/mac80211/tx.c: In function 'ieee80211_subif_start_xmit':
net/mac80211/tx.c:1797:22: warning: 'chanctx_conf' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 18 Jan 2013 20:21:31 +0000 (21:21 +0100)]
mac80211: remove redundant check
There's no need to have two checks for "associated"
in ieee80211_sta_restart(), make the first one locked
to not race (unlikely at this point during resume)
and remove the second check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simon Wunderlich [Wed, 23 Jan 2013 14:15:57 +0000 (15:15 +0100)]
cfg80211: fix channel check in cfg80211_can_use_iftype_chan
In commit "cfg80211: check radar interface combinations" a regression
was introduced which might lead to NULL dereference if the argument
chan = NULL, which might happen in IBSS/wext case (and probably
others).
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Wed, 23 Jan 2013 20:18:12 +0000 (12:18 -0800)]
mac80211: clean up mesh sta allocation warning
This refactoring fixes a "scheduling while atomic" warning
when allocating a mesh station entry while holding the RCU
read lock. Fix this by creating a new function
mesh_sta_info_get(), which correctly handles the locking
and returns under RCU.
Also move some unnecessarily #ifdefed mesh station init
code from sta_info_alloc() to __mesh_sta_info_alloc().
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[change code flow to make sparse happy] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 18 Jan 2013 22:47:05 +0000 (23:47 +0100)]
mac80211: fix aggregation state with current drivers
For drivers that don't actually flush their queues when
aggregation stop with the IEEE80211_AMPDU_TX_STOP_FLUSH
or IEEE80211_AMPDU_TX_STOP_FLUSH_CONT reasons is done,
like iwlwifi or iwlegacy, mac80211 can then transmit on
a TID that the driver still considers busy. This happens
in the following way:
- IEEE80211_AMPDU_TX_STOP_FLUSH requested
- driver marks TID as emptying
- mac80211 removes tid_tx data, this can copy packets
to the TX pending queues and also let new packets
through to the driver
- driver gets unexpected TX as it wasn't completely
converted to the new API
Fortunately, solving this problem is easy as the station
is being destroyed, so such transmit packets can only
happen due to races. Instead of trying to close the race
just let the race not reach the drivers by making two
changes:
1) remove the explicit aggregation session teardown in
the managed mode code, the same thing will be done
when the station is removed, in __sta_info_destroy.
2) When aggregation stop with AGG_STOP_DESTROY_STA is
requested, leave the tid_tx data around as stopped.
It will be cleared and freed in cleanup_single_sta
later, but until then any racy packets will be put
onto the tid_tx pending queue instead of transmitted
which is fine since the station is being removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since drivers can support several BSS / P2P Client
interfaces, the rssi callback needs to inform the driver
about the interface teh rssi event relates to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sun, 20 Jan 2013 17:51:53 +0000 (18:51 +0100)]
ath9k: clean up processing of pending tx frames on reset
Dropping packets from aggregation sessions is usually not a good idea, as
it might upset the synchronization of the BlockAck receive window of the
remote node. The use of the retry_tx parameter to reset/tx-drain functions
also seemed a bit arbitrary.
This patch removes this parameter altogether and ensures that pending tx
frames are not dropped for no good reason.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 20 Jan 2013 17:51:52 +0000 (18:51 +0100)]
ath9k: stop rx after tx
Completing frame transmission can fail if the rx engine is stopped
prematurely, as the hw might be waiting for an ACK from the other side.
Shutting down tx before rx might make the DMA shutdown more reliable.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlegacy: don't return zero on failure paths in il4965_pci_probe()
If hardware is not ready, il4965_pci_probe() breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -EIO as return value in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: don't return zero on failure paths in mwl8k_probe[_hw]()
If pci_iomap() fails in mwl8k_probe(), it breaks off initialization,
deallocates all resources, but returns zero.
There is a similar issue when priv->rxd_ops is NULL in mwl8k_probe_hw().
The patch adds proper error code return values.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Fri, 18 Jan 2013 01:41:57 +0000 (17:41 -0800)]
mwifiex: correction in status codes used for association failure
When AP responds with appropriate status code, we forward that
code correctly to cfg80211. But sometimes when there is no
response from AP, our firmware uses proprietary status codes.
We will map authentication timeout to WLAN_STATUS_AUTH_TIMEOUT
and other proprietary codes to WLAN_STATUS_UNSPECIFIED_FAILURE.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 17 Jan 2013 16:34:32 +0000 (17:34 +0100)]
rt2x00: Improve TX status handling for BlockAckReq frames
Since rt2800 hardware isn't capable of reporting the TX status of
BlockAckReq frames implement the TX status handling of BARs in
rt2x00lib. We keep track of all BARs that are send out and try to
match incoming BAs to the appropriate BARs. This allows us to report a
more or less accurate TX status for BAR frames which in turn improves
BA session stability.
This is loosley based on Christian Lamparter's patch for carl9170
"carl9170: fix HT peer BA session corruption".
We have to walk the list of pending BARs for every rx'red BA even
though most BAs don't belong to any of these BARs as they are just
acknowledging an AMPDU. To keep that overhead low use RCU which allows
us to walk the list of pending BARs without the need to acquire a lock.
This however requires us to _copy_ relevant information from the BAR
(RA, TA, control field, start sequence number) into our BAR list entry.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Tested-by: Andreas Hartmann <andihartmann@01019freenet.de> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Sun, 20 Jan 2013 16:31:30 +0000 (19:31 +0300)]
b43: N-PHY: fix gain in b43_nphy_get_gain_ctl_workaround_ent()
There were no break statements in this switch statement so everything
used the default settings. Per Walter Harms's suggestion, I've replaced
the switch statement and done a little cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chen Gang [Tue, 8 Jan 2013 05:33:03 +0000 (13:33 +0800)]
drivers/net/wireless: need consider the not '\0' terminated string.
in ray_cs.c:
the a_current_ess_id is "Null terminated unless ESSID_SIZE long"
so we need buffer it with '\0' firstly, before using strlen or %s.
additional information:
in drivers/net/wireless/rayctl.h:
"NULL terminated unless 32 long" is a comment at line 616, 664
ESSID_SIZE is 32, at line 190
in include/uapi/linux/wireless.h:
IW_ESSID_MAX_SIZE is also 32
in drivers/net/wireless/ray_cs.c:
use strncpy for it, without '\0' terminated, at line 639
use memcpy for it, assume not '\0' terminated in line 1092..1097
buffer it with '\0' firstly, before using %s, in line 2576, 2598..2600
Signed-off-by: Chen Gang <gang.chen@asianux.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 13 Jan 2013 18:54:58 +0000 (19:54 +0100)]
ath9k_hw: fix RF bank initialization
ar900*_init_mode_regs needs to be called before RF banks are allocated,
otherwise the storage size of RF banks isn't known. This patch fixes
a memory overrun that can show up as a crash on unloading the module.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sat, 19 Jan 2013 18:36:49 +0000 (12:36 -0600)]
rtlwifi: Fix build warning introduced by commit a290593
The kbuild test robot reports the following warning with x86_64-randconfig-x955:
warning: (RTL8192CE && RTL8192SE && RTL8192DE && RTL8723AE && RTL8192CU) selects
RTLWIFI which has unmet direct dependencies (NETDEVICES && WLAN &&
(RTL8192CE || RTL8192CU || RTL8192SE || RTL8192DE))
This warning was introduced in commit a290593, "rtlwifi: Modify files for addition
of rtl8723ae", and is d ue to a missing dependence of RTLWIFI on RTL8723AE.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: kbuild test robot <fengguang.wu@intel.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Jaroslav Skarvada <jskarvad@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 14 Jan 2013 14:14:34 +0000 (15:14 +0100)]
mac80211: allow drivers to access IPv6 information
To be able to implement NS response offloading (in
regular operation or while in WoWLAN) drivers need
to know the IPv6 addresses assigned to interfaces.
Implement an IPv6 notifier in mac80211 to call the
driver when addresses change.
Unlike for IPv4, implement it as a callback rather
than as a list in the BSS configuration, that is
more flexible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 16 Jan 2013 09:39:44 +0000 (10:39 +0100)]
mac80211: improve aggregation debug messages
A lot of the aggregation messages don't indicate the
station so they're hard to understand if there are
multiple sessions in progress. Make that easier by
adding the MAC address to most messages. Also add
the TID if it wasn't already there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 14 Jan 2013 15:39:07 +0000 (16:39 +0100)]
mac80211: remove ARP filter enable/disable logic
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Yoni Divinsky [Wed, 30 May 2012 08:36:39 +0000 (11:36 +0300)]
mac80211: add op to configure default key id
There are hardwares which support offload of data packets
for example when auto ARP is enabled the hw will send
the ARP response. In such cases if WEP encryption is
configured the hw must know the default WEP key in order
to encrypt the packets correctly.
When hw_accel is enabled and encryption type is set to WEP,
the driver should get the default key index from mac80211.
To ease further DFS development regarding interface combinations, use
the interface combinations structure to test for radar capabilities.
Drivers can specify which channel widths they support, and in which
modes. Right now only a single AP interface is allowed, but as the
DFS code evolves other combinations can be enabled.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni Malinen [Tue, 15 Jan 2013 15:15:57 +0000 (17:15 +0200)]
cfg80211: Allow use_mfp to be specified with the connect command
The NL80211_ATTR_USE_MFP attribute was originally added for
NL80211_CMD_ASSOCIATE, but it is actually as useful (if not even more
useful) with NL80211_CMD_CONNECT, so process that attribute with the
connect command, too.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bob Copeland [Wed, 9 Jan 2013 17:34:56 +0000 (12:34 -0500)]
mac80211: add encrypt headroom to PERR frames
Mesh PERR action frames are robust and thus may be encrypted, so add
proper head/tailroom to allow this. Fixes this warning when operating
a Mesh STA on ath5k:
Bob Copeland [Wed, 9 Jan 2013 17:34:55 +0000 (12:34 -0500)]
mac80211: set NEED_TXPROCESSING for PERR frames
A user reported warnings in ath5k due to transmitting frames with no
rates set up. The frames were Mesh PERR frames, and some debugging
showed an empty control block with just the vif pointer:
nl80211: allow user-space to set address for P2P_DEVICE
As per email discussion Jouni Malinen pointed out that:
"P2P message exchanges can be executed on the current operating channel
of any operation (both P2P and non-P2P station). These can be on 5 GHz
and even on 60 GHz (so yes, you _can_ do GO Negotiation on 60 GHz).
As an example, it would be possible to receive a GO Negotiation Request
frame on a 5 GHz only radio and then to complete GO Negotiation on that
band. This can happen both when connected to a P2P group (through client
discoverability mechanism) and when connected to a legacy AP (assuming
the station receive Probe Request frame from full scan in the beginning
of P2P device discovery)."
This means that P2P messages can be sent over different radio devices.
However, these should use the same P2P device address so it should be
able to provision this from user-space. This patch adds a parameter for
this to struct vif_params which should only be used during creation of
the P2P device interface.
Marco Porsch [Mon, 7 Jan 2013 15:04:52 +0000 (16:04 +0100)]
{cfg,nl}80211: mesh power mode primitives and userspace access
Add the nl80211_mesh_power_mode enumeration which holds possible
values for the mesh power mode. These modes are unknown, active,
light sleep and deep sleep.
Add power_mode entry to the mesh config structure to hold the
user-configured default mesh power mode. This value will be used
for new peer links.
Add the dot11MeshAwakeWindowDuration value to the mesh config.
The awake window is a duration in TU describing how long the STA
will stay awake after transmitting its beacon in PS mode.
Add access routines to:
- get/set local link-specific power mode (STA)
- get remote STA's link-specific power mode (STA)
- get remote STA's non-peer power mode (STA)
- get/set default mesh power mode (mesh config)
- get/set mesh awake window duration (mesh config)
All config changes may be done at mesh runtime and take effect
immediately.
Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com> Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
[fix commit message line length, error handling in set station] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Marco Porsch [Mon, 7 Jan 2013 15:04:51 +0000 (16:04 +0100)]
{cfg,nl,mac}80211: set beacon interval and DTIM period on mesh join
Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.
Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.
Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Marco Porsch [Mon, 7 Jan 2013 15:04:49 +0000 (16:04 +0100)]
mac80211: update mesh peer link counter during userspace peering
The established peer link count is indicated in mesh beacons and
used for other internal tasks. Previously it was not updated when
authenticated peering is performed in userspace.
Signed-off-by: Marco Porsch <marco@cozybit.com> Acked-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Chun-Yeow Yeoh [Thu, 10 Jan 2013 15:31:54 +0000 (23:31 +0800)]
mac80211: allow disable power save in mesh
Allow mesh interface to disable the power save which is by default
turn on in certain chipset. Testing with 2 units of ZCN-1523H-5-16
featuring AR9280 chipset which have power save enabled by default.
Constant reset if the average signal of the peer mesh STA is below
-80 dBm and power save is enabled.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 10 Jan 2013 23:28:01 +0000 (00:28 +0100)]
mac80211: call restart complete at wowlan resume time
When the driver's resume function can't completely
restore the configuration in the device, it returns
1 from the callback which will be treated like a HW
restart request, but done directly.
In this case, also call the driver's restart_complete()
function so it can finish the reconfiguration there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 10 Jan 2013 22:55:33 +0000 (23:55 +0100)]
mac80211: fix resume from WoWLAN
My commit 529ba6e9313dbe60dab7e72c6fdf647a012e9f5b
("mac80211: clean up association better in suspend")
introduced a bug when resuming from WoWLAN when a
device reset is desired. This case must not use the
suspend_bss_conf as it hasn't been stored.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: Optimize scans on current operating channel.
we do not disable PS while going back to operational channel (on
ieee80211_scan_state_suspend) and deffer that until scan finish.
But since we are allowed to send frames, we can send a frame to AP
without PM bit set, so disable PS on AP side. Then when we switch
to off-channel (in ieee80211_scan_state_resume) we do not enable PS.
Hence we are off-channel with PS disabled, frames are not buffered
by AP.
To fix remove offchannel_ps_disable argument and always enable PS when
going off-channel and disable it when going on-channel, like it was
before.
Johannes Berg [Fri, 11 Jan 2013 13:34:25 +0000 (14:34 +0100)]
mac80211: fix FT roaming
During FT roaming, wpa_supplicant attempts to set the
key before association. This used to be rejected, but
as a side effect of my commit 66e67e418908442389d3a9e
("mac80211: redesign auth/assoc") the key was accepted
causing hardware crypto to not be used for it as the
station isn't added to the driver yet.
It would be possible to accept the key and then add it
to the driver when the station has been added. However,
this may run into issues with drivers using the state-
based station adding if they accept the key only after
association like it used to be.
For now, revert to the behaviour from before the auth
and assoc change.
The rate scaling won't treat the information in a frame
with IEEE80211_TX_CTL_AMPDU set if IEEE80211_TX_STAT_AMPDU
is cleared. But all the frames coming from an AGG tx queue
have IEEE80211_TX_CTL_AMPDU set, and IEEE80211_TX_STAT_AMPDU
is set only if the frame was sent in an AMPDU.
This means that all the data in frames in AGG tx queues that
aren't sent as an AMPDU is thrown away.
This is even more harmful when in bad link conditions, the
frames are sent in an AMPDU and then finally sent as single
frame. So a lot of failures weren't reported and the rate
scaling got stuck in high rates leading to very poor
connectivity.
Fix that by clearing IEEE80211_TX_CTL_AMPDU when the frame
isn't part of an AMPDU.
Johannes Berg [Tue, 8 Jan 2013 10:25:44 +0000 (11:25 +0100)]
iwlwifi: enable communication with WoWLAN firmware
On resuming, the opmode may have to be able to talk
to the WoWLAN/D3 firmware in order to query it about
its status and wakeup reasons. To do that, the opmode
has to call the new d3_resume() transport API which
will set up the device for command communcation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 8 Jan 2013 23:47:07 +0000 (00:47 +0100)]
iwlwifi: simplify scheduler memory clearing
Writing 130 dwords into the device one by one is
rather inefficient, every one needs to lock, grab
NIC access (a few register reads/writes) and then
write the address and data registers.
Use the new memory clearing function to make this
easier and faster.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 8 Jan 2013 09:26:17 +0000 (10:26 +0100)]
iwlwifi: don't enable all interrupts on resuming
Enabling the RF-kill interrupt is sufficient for getting
RF-kill notifications, and no other interrupt is needed
as the device isn't functional when suspended and will be
restarted/reconfigured when mac80211 resumes it later.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Nathan Hintz [Sat, 12 Jan 2013 10:46:16 +0000 (02:46 -0800)]
bcma: add support for 1 and 2 byte extended config space access
The sanity checks allow 1 and 2 byte reads/writes of the extended
PCI config space to proceed; however, the code only supports 4
byte reads/writes. This patch adds support for 1 and 2 byte
reads/writes of the extended PCI config space.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nathan Hintz [Sat, 12 Jan 2013 10:46:15 +0000 (02:46 -0800)]
bcma: don't map/unmap a subset of the PCI config space
For PCI config space access offsets < 256 for device '0',
bcma_extpci_write_config performs an 'ioremap_nocache' on a 4 byte
section of the PCI config space (an area that has already
previously been mapped), and then subsequently unmaps that 4 byte
section. This can't be a good thing for future read access from
that now unmapped location. Modify the config space writes to use
the existing access functions (similar to how it is done for the reads).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 14 Jan 2013 20:08:52 +0000 (15:08 -0500)]
Merge tag 'nfc-next-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"This is the first NFC patchset targeted at the 3.9 merge window.
It brings the following goodies:
- LLCP socket timestamping (To be used e.g with the recently released nfctool
application for a more efficient skb timestamping when sniffing).
- A pretty big pn533 rework from Waldemar, preparing the driver to support
more flavours of pn533 based devices.
- HCI changes from Eric in preparation for the microread driver support.
- Some LLCP memory leak fixes, cleanups and slight improvements.
- pn544 and nfcwilink move to the devm_kzalloc API.
- An initial Secure Element (SE) API.
- An nfc.h license change from the original author, allowing non GPL
application code to safely include it."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 14 Jan 2013 15:56:46 +0000 (16:56 +0100)]
ath9k: disable the tasklet before taking the PCU lock
Fixes a reported CPU soft lockup where the tasklet tries to acquire the
lock and blocks while ath_prepare_reset (holding the lock) waits for it
to complete.
Cc: stable@vger.kernel.org Reported-by: Robert Shade <robert.shade@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 14 Jan 2013 09:50:15 +0000 (10:50 +0100)]
ath9k: remove sc->rx.rxbuflock to fix a deadlock
The commit "ath9k: fix rx flush handling" added a deadlock that happens
because ath_rx_tasklet is called in a section that has already taken the
rx buffer lock.
It seems that the only purpose of the rxbuflock was a band-aid fix to the
reset vs rx tasklet race, which has been properly fixed in the commit
"ath9k: add a better fix for the rx tasklet vs rx flush race".
Now that the fix is in, we can safely remove the lock to avoid such issues.
Cc: stable@vger.kernel.org Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
nfc.h being GPL makes it quite controversial for non GPL applications to
include it.
Moreover, nfc.h only includes structures and API definitions that are hardly
copyrightable.
Signed-off-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The reg_notifier()'s return value need not be checked
as it is only supposed to do post regulatory work and
that should never fail. Any behaviour to regulatory
that needs to be considered before cfg80211 does work
to a driver should be specified by using the already
existing flags, the reg_notifier() just does post
processing should it find it needs to.
Also make lbs_reg_notifier static.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[move lbs_reg_notifier to not break compile] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Nathan Hintz [Thu, 10 Jan 2013 16:54:09 +0000 (17:54 +0100)]
bcma: return the mips irq number in bcma_core_irq
The irq signal numbers that are send by the cpu are increased by 2 from
the number programmed into the mips core by bcma.
Return the irq number on which the irqs are send in bcma_core_irq() now.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC drivers/bcma/driver_mips.o
drivers/bcma/driver_mips.c: In function 'bcma_core_mips_init':
drivers/bcma/driver_mips.c:302:4: error: implicit declaration of
function 'bcma_core_irq' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[6]: *** [drivers/bcma/driver_mips.o] Error 1
Reported-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Thu, 10 Jan 2013 10:45:14 +0000 (11:45 +0100)]
ath9k: fix spectral scan endless mode on AR9002
There was a copy+paste error in ar9002 for the endless spectral mode,
fix that.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Thu, 6 Dec 2012 22:10:40 +0000 (23:10 +0100)]
drivers/nfc/nfcwilink.c: use devm_kzalloc
devm_kzalloc allocates memory that is released when a driver detaches.
This patch uses devm_kzalloc for data that is allocated in the probe
function of a platform device and is only freed in the remove function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Piotr Haber [Thu, 10 Jan 2013 10:20:48 +0000 (11:20 +0100)]
brcmsmac: increase timer reference count for new timers only
On hardware reintialization reference count of
already existing timers would be increased again.
This leads to problems on module unloading.
Cc: stable@vger.kernel.org Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 9 Jan 2013 15:16:56 +0000 (16:16 +0100)]
ath9k: fix rx flush handling
Right now the rx flush is not doing anything useful on AR9003+, as it only
works if the buffers in the rx FIFO have not been purged yet, as is done
by ath_stoprecv.
To fix this, always call ath_flushrecv from within ath_stoprecv before
the FIFO is emptied, but still after the hw receive path has been stopped.
This ensures that frames received (and ACKed by the hardware) shortly before
a reset will be seen by the software, which should improve A-MPDU session
stability.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 9 Jan 2013 15:16:55 +0000 (16:16 +0100)]
ath9k: add a better fix for the rx tasklet vs rx flush race
Ensure that the rx tasklet is no longer running when entering the reset path.
Also remove the distinction between flush and no-flush frame processing.
If a frame has been received and ACKed by the hardware, the stack needs to see
it, so that the BA receive window does not go out of sync.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 9 Jan 2013 15:16:54 +0000 (16:16 +0100)]
ath9k: remove the WARN_ON that triggers if generating a beacon fails
During teardown, mac80211 will not return a new beacon. This is normal and
handled properly in the driver, so there's no need to spam the user with a kernel
warning here.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 9 Jan 2013 15:16:53 +0000 (16:16 +0100)]
ath9k: fix double-free bug on beacon generate failure
When the next beacon is sent, the ath_buf from the previous run is reused.
If getting a new beacon from mac80211 fails, bf->bf_mpdu is not reset, yet
the skb is freed, leading to a double-free on the next beacon tx attempt,
resulting in a system crash.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 9 Jan 2013 15:16:52 +0000 (16:16 +0100)]
ath9k: do not link receive buffers during flush
On AR9300 the rx FIFO needs to be empty during reset to ensure that no
further DMA activity is generated, otherwise it might lead to memory
corruption issues.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
SKBs that are allocated in the HTC layer do not have callbacks
registered and hence ended up not being freed, Fix this by freeing
them properly in the TX completion routine.
Cc: <stable@vger.kernel.org> Reported-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log