[media] Add support for 'Digital Dual TV Receiver CTVDIGDUAL v2
Tested on a MIPSel box with 3.3.6 kernel
The kernel output when the device will be detected follows:
usbcore: registered new interface driver dvb_usb_it913x
it913x: Chip Version=01 Chip Type=9135
it913x: Remote propriety (raw) mode
it913x: Dual mode=3 Tuner Type=38
it913x: Chip Version=01 Chip Type=9135
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in cold state
usb 2-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9137-01.fw'
it913x: FRM Starting Firmware Download
it913x: FRM Firmware Download Completed - Resetting Device
it913x: Chip Version=01 Chip Type=9135
it913x: Firmware Version 204147968
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in warm state
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 1 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_1)...
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 2 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_2)...
usb 2-1: dvb_usb_v2: 'Digital Dual TV Receiver CTVDIGDUAL_V2' successfully initialized and connected
RC part not tested
Zoran Turalija [Sun, 2 Jun 2013 17:56:33 +0000 (14:56 -0300)]
[media] stb0899: allow minimum symbol rate of 2000000
Looks like product datasheets for tuners containing STB0899 are
suggesting specification for min. symbol rate of 2MS/s.
Some specs found here, all suggesting 2MS/s for min. symbol rate:
Comtech DVBS2-6899
http://comtech.sg1002.myweb.hinet.net/pdf/dvbs2-6899.pdf
TechniSat SkyStar HD2
http://www.scaistar.com/skystar2/skystarhd2.htm
Azurewave AD-SP400
http://www.pulsat.com/products/AzureWave-AD%252dSP400-High-Definition-PC-Card.html
New patch:
This makes minimum symbol rate driver capabilities on par with some
accessible datasheet specifications*, and allows tuning on linux to
transponders that have symbol rate between 2000000-5000000, too.
Patch was tested successfully on Eutelsat 16A transponders that
became reachable with it (2000000 < symbol rate < 5000000):
* DVB/S 12507050 V 2532000 3/4
* DVB/S2 12574000 V 4355000 3/4 8PSK
* DVB/S 12593000 V 2500000 2/3
* DVB/S 12596940 V 2848000 2/3
* DVB/S 12600750 V 2500000 1/2
* DVB/S 12675590 H 4248000 3/4
(*) Datasheet: http://comtech.sg1002.myweb.hinet.net/pdf/dvbs2-6899.pdf
Maximum Symbol Rate
QPSK/LDPC/PCH: 20-30Mbps
8PSK/LDPC/BCH: 10-30Mbps
DVB: 2-45Mbps
^--------- min. symbol rate
Reinhard Nißl [Sun, 2 Jun 2013 17:52:43 +0000 (14:52 -0300)]
[media] stb0899: fix inversion enum values to match usage with CFR
Throughout the zig-zag-implementations, inversion is taken into
account when reading and writing the CFR register, which contains
the derotator frequency. As swapping IQ signals changes the sign
of that register for example, the idea is to compensate that sign
change by multiplying the register value with the inversion enum
value.
The current enum values 0 and 1 for IQ_SWAP_OFF and IQ_SWAP_ON
don't work in the case IQ_SWAP_OFF, due to the multiplication by
zero (I've only found a single device which actually uses
IQ_SWAP_OFF in it's config).
I've changed the enum values to +1 and -1 to accommodate to the
intended usage.
Reinhard Nißl [Sun, 2 Jun 2013 17:52:02 +0000 (14:52 -0300)]
[media] stb0899: enable auto inversion handling unconditionally
It seems that current inversion handling addresses only the signal
routing on the PCB, i. e. IQ signals are either swapped or not.
But when the device is operated in a Satellite Channel Router (SCR)
environment, an additional inversion is required due to the way how
the SCR works. Therefore it makes sense to me to always enable auto
inversion handling and drop the enum value IQ_SWAP_AUTO.
Zoran Turalija [Sun, 2 Jun 2013 17:40:51 +0000 (14:40 -0300)]
[media] stb0899: allow minimum symbol rate of 1000000
This makes minimum symbol rate driver capabilities on par with
windows driver, and allows tuning on linux to transponders that
have symbol rate below 5000000, too.
Patch was tested successfully on Eutelsat 16A transponders that
became reachable with it (1000000 < symbol rate < 5000000):
* DVB/S 12507050 V 2532000 3/4
* DVB/S2 12574000 V 4355000 3/4 8PSK
* DVB/S 12593000 V 2500000 2/3
* DVB/S 12596940 V 2848000 2/3
* DVB/S 12600750 V 2500000 1/2
* DVB/S 12675590 H 4248000 3/4
Reinhard Nißl [Sun, 2 Jun 2013 17:37:06 +0000 (14:37 -0300)]
[media] stb0899: sign extend raw CRL_FREQ value
Contrary to the chip's specs, the register's value is signed, so we
need to sign extend the value before using it in calculations like
when determining the offset frequency.
[media] dib8000: Fix dib8000_set_frontend() never setting ret
drivers/media/dvb-frontends/dib8000.c: In function ‘dib8000_set_frontend’:
drivers/media/dvb-frontends/dib8000.c:3556: warning: ‘ret’ is used uninitialized in this function
Remove the variable and return zero instead.
Maintaining the users count using an atomic variable makes sure that
access to the counter won't be racy, but doesn't serialize access to the
operations protected by the counter. This creates a race condition that
could result in the status URB being submitted multiple times.
Use a mutex to protect the users count and serialize access to the
status start and stop operations.
Joseph Salisbury [Wed, 15 May 2013 20:38:48 +0000 (17:38 -0300)]
[media] uvcvideo: quirk PROBE_DEF for Alienware X51 OmniVision webcam
BugLink: http://bugs.launchpad.net/bugs/1180409
OminiVision webcam 0x05a9:0x2643 needs the same UVC_QUIRK_PROBE_DEF
as other OmniVision models to work properly.
Kamal Mostafa [Mon, 15 Apr 2013 19:01:51 +0000 (16:01 -0300)]
[media] uvcvideo: quirk PROBE_DEF for Dell Studio / OmniVision webcam
BugLink: https://bugs.launchpad.net/bugs/1168430
OminiVision webcam 0x05a9:0x264a (in Dell Studio Hybrid 140g) needs the
same UVC_QUIRK_PROBE_DEF as other OmniVision model to be recognized
consistently.
Philipp Zabel [Thu, 23 May 2013 13:43:01 +0000 (10:43 -0300)]
[media] coda: do not call v4l2_m2m_job_finish from .job_abort
If we just declare the job finished here while the CODA is still
running, the call to v4l2_m2m_ctx_release in coda_release, which
is supposed to wait for a running job to finish, will return
immediately and free memory that the CODA is still using.
Just set the 'aborting' flag and let coda_irq_handler deal with it.
Philipp Zabel [Thu, 23 May 2013 13:43:00 +0000 (10:43 -0300)]
[media] coda: replace completion with mutex
Not only do we need to wait for job completion when we want to
call a command on the CODA in start/stop_streaming, we also need
to make sure that a new job doesn't start before the command
finished.
Use a mutex to lock the coda command handling. On timeout, the
device_run job must be marked as finished and the mutex released,
as otherwise coda_release will block.
Philipp Zabel [Thu, 23 May 2013 13:42:59 +0000 (10:42 -0300)]
[media] coda: add coda_encode_header helper function
In preparation for CODA7541 and CODA960 multi-stream support and for
replacement of the completion with a mutex lock, consolidate the
header encoding in a helper function.
Philipp Zabel [Thu, 23 May 2013 13:42:58 +0000 (10:42 -0300)]
[media] coda: per-product list of codecs instead of list of formats
This patch adds a list of supported codecs per device type which is used to
determine the allowed pixel formats and maximum frame sizes depending on the
possible codecs. It allows frame sizes larger than 720 x 576 on CODA7 and adds
support for the YVU420 (planar YUV 4:2:0 with switched Cb and Cr) format.
Other uncompressed formats that could be added in the future are the chroma
interleaved NV12 and NV21 formats and the multiplanar variants YUV420M,
YVU420M, NV12M, and NV21M.
Further, rawstreamon is renamed to streamon_out and compstreamon is renamed
to streamon_cap in preparation for decoding support. The maximum encoded
frame buffer size is increased to 1 MiB.
Instead of tracking inst_type and codec across S_FMT calls, set the codec
and inst_type in start_streaming.
Philipp Zabel [Tue, 21 May 2013 13:31:25 +0000 (10:31 -0300)]
[media] coda: fix error return value if v4l2_m2m_ctx_init fails
Use ret from the outer scope, instead of redefining it in the
conditional clause. That way the error value reaches the end of
the function as intended.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lad, Prabhakar [Tue, 14 May 2013 09:45:31 +0000 (06:45 -0300)]
[media] media: i2c: tvp7002: rearrange description of structure members
This patch rearranges the description of field members of
struct tvp7002_config. Also as the all the fields where accepting
a value either 0/1, made the members as bool.
Wei Yongjun [Mon, 13 May 2013 13:00:01 +0000 (10:00 -0300)]
[media] sta2x11_vip: fix error return code in sta2x11_vip_init_one()
The orig code will release all the resources if v4l2_device_register()
failed and return 0. But what we need in this case is to return an
negative error code to let the caller known we are failed.
So the patch save the return value of v4l2_device_register() to 'ret'
and return it when error.
Randy Dunlap [Mon, 20 May 2013 15:32:39 +0000 (12:32 -0300)]
[media] media: fix hdpvr kconfig/build errors
Fix hdpvr build errors when CONFIG_I2C=m and VIDEO_V4L2=m and
VIDEO_HDPVR=y.
drivers/built-in.o: In function `hdpvr_disconnect':
hdpvr-core.c:(.text+0xef542): undefined reference to `v4l2_device_disconnect'
hdpvr-core.c:(.text+0xef57e): undefined reference to `i2c_del_adapter'
hdpvr-core.c:(.text+0xef58a): undefined reference to `video_unregister_device'
drivers/built-in.o: In function `hdpvr_delete':
(.text+0xef5b9): undefined reference to `video_device_release'
drivers/built-in.o: In function `hdpvr_probe':
hdpvr-core.c:(.text+0xef63a): undefined reference to `v4l2_device_register'
hdpvr-core.c:(.text+0xefd97): undefined reference to `i2c_del_adapter'
drivers/built-in.o: In function `hdpvr_s_ctrl':
hdpvr-video.c:(.text+0xf03c0): undefined reference to `v4l2_ctrl_activate'
drivers/built-in.o: In function `hdpvr_device_release':
hdpvr-video.c:(.text+0xf0470): undefined reference to `v4l2_device_unregister'
hdpvr-video.c:(.text+0xf0479): undefined reference to `v4l2_ctrl_handler_free'
hdpvr-video.c:(.text+0xf048f): undefined reference to `i2c_del_adapter'
drivers/built-in.o: In function `hdpvr_open':
hdpvr-video.c:(.text+0xf0570): undefined reference to `video_devdata'
hdpvr-video.c:(.text+0xf057b): undefined reference to `v4l2_fh_init'
hdpvr-video.c:(.text+0xf0583): undefined reference to `v4l2_fh_add'
drivers/built-in.o: In function `video_drvdata':
hdpvr-video.c:(.text+0xf08a0): undefined reference to `video_devdata'
drivers/built-in.o: In function `vidioc_s_dv_timings':
hdpvr-video.c:(.text+0xf0d34): undefined reference to `v4l_match_dv_timings'
drivers/built-in.o: In function `hdpvr_poll':
hdpvr-video.c:(.text+0xf1455): undefined reference to `v4l2_ctrl_poll'
drivers/built-in.o: In function `hdpvr_release':
hdpvr-video.c:(.text+0xf18f6): undefined reference to `v4l2_fh_release'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1be3): undefined reference to `v4l2_ctrl_handler_init_class'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c19): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c42): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c6b): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1cac): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1cd5): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o:(.text+0xf1cfe): more undefined references to `v4l2_ctrl_new_std' follow
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1d75): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1d9e): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1dc3): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1de5): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e18): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e4b): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e90): undefined reference to `v4l2_ctrl_cluster'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e98): undefined reference to `v4l2_ctrl_handler_setup'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1ec1): undefined reference to `video_device_alloc'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1f85): undefined reference to `__video_register_device'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1fac): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `hdpvr_register_ir_tx_i2c':
(.text+0xf238f): undefined reference to `i2c_new_device'
drivers/built-in.o: In function `hdpvr_register_ir_rx_i2c':
(.text+0xf2434): undefined reference to `i2c_new_device'
drivers/built-in.o: In function `hdpvr_register_i2c_adapter':
(.text+0xf2514): undefined reference to `i2c_add_adapter'
drivers/built-in.o:(.rodata+0x1b368): undefined reference to `video_ioctl2'
drivers/built-in.o:(.rodata+0x1b690): undefined reference to `v4l2_ctrl_log_status'
drivers/built-in.o:(.rodata+0x1b6f8): undefined reference to `v4l2_ctrl_subscribe_event'
drivers/built-in.o:(.rodata+0x1b700): undefined reference to `v4l2_event_unsubscribe'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At least on s390, gcc complains about that:
drivers/media/i2c/saa7115.c: In function 'saa711x_detect_chip.constprop.2':
drivers/media/i2c/saa7115.c:1647:1: warning: 'saa711x_detect_chip.constprop.2' uses dynamic stack allocation [enabled by default]
While for me the above report seems utterly bogus, as the
compiler should be optimizing saa711x_detect_chip, merging
it with saa711x_detect_chip and changing:
char chip_ver[size - 1];
to
char chip_ver[16];
because this function is only called on this code snippet:
char name[17];
...
ident = saa711x_detect_chip(client, id, name, sizeof(name));
It seems that gcc is not optimizing it, at least on s390.
As getting rid of it is easy, let's do it.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Al Viro [Thu, 9 May 2013 18:03:33 +0000 (15:03 -0300)]
[media] videobuf_vm_{open,close} race fixes
just use videobuf_queue_lock(map->q) to protect map->count; vm_area_operations
->open() and ->close() are called just under vma->vm_mm->mmap_sem, which
doesn't help the drivers at all, since clonal VMAs are normally in different
address spaces...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Randy Dunlap [Wed, 8 May 2013 20:28:13 +0000 (17:28 -0300)]
[media] media/usb: fix kconfig dependencies
(a.k.a. Kconfig bool depending on a tristate considered harmful)
Fix various build errors when CONFIG_USB=m and media USB drivers
are builtin. In this case, CONFIG_USB_ZR364XX=y,
CONFIG_VIDEO_PVRUSB2=y, and CONFIG_VIDEO_STK1160=y.
This is caused by (from drivers/media/usb/Kconfig):
menuconfig MEDIA_USB_SUPPORT
bool "Media USB Adapters"
depends on USB && MEDIA_SUPPORT
=m =y
so MEDIA_USB_SUPPORT=y and all following Kconfig 'source' lines
are included. By adding an "if USB" guard around most of this file,
the needed dependencies are enforced.
drivers/built-in.o: In function `zr364xx_start_readpipe':
zr364xx.c:(.text+0xc726a): undefined reference to `usb_alloc_urb'
zr364xx.c:(.text+0xc72bb): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `zr364xx_stop_readpipe':
zr364xx.c:(.text+0xc72fd): undefined reference to `usb_kill_urb'
zr364xx.c:(.text+0xc7309): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `read_pipe_completion':
zr364xx.c:(.text+0xc7acc): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `send_control_msg.constprop.12':
zr364xx.c:(.text+0xc7d2f): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_ctl_timeout':
pvrusb2-hdw.c:(.text+0xcadb6): undefined reference to `usb_unlink_urb'
pvrusb2-hdw.c:(.text+0xcadcb): undefined reference to `usb_unlink_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc42c): undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc448): undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc5f9): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc65a): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc666): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_send_request_ex.part.22':
pvrusb2-hdw.c:(.text+0xccbe3): undefined reference to `usb_submit_urb'
pvrusb2-hdw.c:(.text+0xccc83): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `pvr2_hdw_remove_usb_stuff.part.25':
pvrusb2-hdw.c:(.text+0xcd3f9): undefined reference to `usb_kill_urb'
pvrusb2-hdw.c:(.text+0xcd405): undefined reference to `usb_free_urb'
pvrusb2-hdw.c:(.text+0xcd421): undefined reference to `usb_kill_urb'
pvrusb2-hdw.c:(.text+0xcd42d): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_hdw_device_reset':
(.text+0xcd658): undefined reference to `usb_lock_device_for_reset'
drivers/built-in.o: In function `pvr2_hdw_device_reset':
(.text+0xcd664): undefined reference to `usb_reset_device'
drivers/built-in.o: In function `pvr2_hdw_cpureset_assert':
(.text+0xcd6f9): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_hdw_cpufw_set_enabled':
(.text+0xcd84e): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_upload_firmware1':
pvrusb2-hdw.c:(.text+0xcda47): undefined reference to `usb_clear_halt'
pvrusb2-hdw.c:(.text+0xcdb04): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_upload_firmware2':
(.text+0xce7dc): undefined reference to `usb_bulk_msg'
drivers/built-in.o: In function `pvr2_stream_buffer_count':
pvrusb2-io.c:(.text+0xd2e05): undefined reference to `usb_alloc_urb'
pvrusb2-io.c:(.text+0xd2e5b): undefined reference to `usb_kill_urb'
pvrusb2-io.c:(.text+0xd2e9f): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_stream_internal_flush':
pvrusb2-io.c:(.text+0xd2f9b): undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `pvr2_buffer_queue':
(.text+0xd3328): undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `pvr2_buffer_queue':
(.text+0xd33ea): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `stk1160_read_reg':
(.text+0xd3efa): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `stk1160_write_reg':
(.text+0xd3f4f): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `stop_streaming':
stk1160-v4l.c:(.text+0xd4997): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `start_streaming':
stk1160-v4l.c:(.text+0xd4a9f): undefined reference to `usb_set_interface'
stk1160-v4l.c:(.text+0xd4afa): undefined reference to `usb_submit_urb'
stk1160-v4l.c:(.text+0xd4ba3): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `stk1160_isoc_irq':
stk1160-video.c:(.text+0xd509b): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `stk1160_cancel_isoc':
(.text+0xd50ef): undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `stk1160_free_isoc':
(.text+0xd5155): undefined reference to `usb_free_coherent'
drivers/built-in.o: In function `stk1160_free_isoc':
(.text+0xd515d): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `stk1160_alloc_isoc':
(.text+0xd5278): undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `stk1160_alloc_isoc':
(.text+0xd52c2): undefined reference to `usb_alloc_coherent'
drivers/built-in.o: In function `stk1160_alloc_isoc':
(.text+0xd53c4): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `zr364xx_driver_init':
zr364xx.c:(.init.text+0x463e): undefined reference to `usb_register_driver'
drivers/built-in.o: In function `pvr_init':
pvrusb2-main.c:(.init.text+0x4662): undefined reference to `usb_register_driver'
drivers/built-in.o: In function `stk1160_usb_driver_init':
stk1160-core.c:(.init.text+0x467d): undefined reference to `usb_register_driver'
drivers/built-in.o: In function `zr364xx_driver_exit':
zr364xx.c:(.exit.text+0x1377): undefined reference to `usb_deregister'
drivers/built-in.o: In function `pvr_exit':
pvrusb2-main.c:(.exit.text+0x1389): undefined reference to `usb_deregister'
drivers/built-in.o: In function `stk1160_usb_driver_exit':
stk1160-core.c:(.exit.text+0x13a0): undefined reference to `usb_deregister'
Suggested-by: "Yann E. MORIN" <yann.morin.1998@free.fr> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] saa7115: Add register setup and config for gm7113c
The gm7113c chip is similar to the original saa7113 chip, so I try to
re-use most of the saa7113 specific setup-/configuration registers.
According to the datasheet, the gm7113c chip has not implemented
any register-addresses after 0x1f, so I add a new entry to for the chip
to the saa711x_has_reg function.
The devices I've seen using this chip will fail to get stable video-sync
if these registers are not zeroed:
R_14_ANAL_ADC_COMPAT_CNTL
R_15_VGATE_START_FID_CHG
R_16_VGATE_STOP
R_17_MISC_VGATE_CONF_AND_MSB
The saa711x_set_v4lstd is updated to send a simpler configuration-table
to avoid setting these registers.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a code that (auto)detects gm7113c clones. The auto-detection
here is not perfect, as, on contrary to what it would be expected
by looking into its datasheets some devices would return, instead:
saa7115 0-0025: chip 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 @ 0x4a is unknown
(found on a device labeled as GM7113C 1145 by Ezequiel Garcia)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Tested-by: Jon Arne Jørgensen <jonarne@jonarne.no> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] saa7115: move the autodetection code out of the probe function
As we're now seeing other variants from chinese clones, like
gm1113c, we'll need to add more bits at the detection code.
So, move it into a separate function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Tested-by: Jon Arne Jørgensen <jonarne@jonarne.no> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] wl128x: do not call copy_to_user() while holding spinlocks
copy_to_user() must not be called with spinlocks held, but it is in
fmc_transfer_rds_from_internal_buff().
The patch copies data to tmpbuf, releases spinlock and then passes it to userspace.
By the way there is a small unification: replace a couple of hardcoded constants by a macro.
Found by Linux Driver Verification project (linuxtesting.org).
Lad, Prabhakar [Fri, 3 May 2013 07:17:19 +0000 (04:17 -0300)]
[media] media: i2c: tvp7002: enable TVP7002 decoder for media controller based usage
This patch enables tvp7002 decoder driver for media controller
based usage by adding v4l2_subdev_pad_ops operations support
for enum_mbus_code, set_pad_format, get_pad_format and media_entity_init()
on probe and media_entity_cleanup() on remove.
Ondrej Zary [Sun, 14 Apr 2013 20:26:21 +0000 (17:26 -0300)]
[media] bttv: Add CyberVision CV06
Add CyberVision CV06 4-camera card (from CyberVision SV card kit):
http://www.cybervision.com.tw/products-swcard_kits-sv.html
There are some interesting things on the card but they're not supported:
4 LEDs, a connector with 4 IN and 4 OUT pins, RESET IN and RESET OUT
connectors, a relay and CyberVision CV8088-SV16 chip
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ondrej Zary [Sun, 14 Apr 2013 15:39:09 +0000 (12:39 -0300)]
[media] bttv: Add noname Bt848 capture card with 14MHz xtal
Add support for noname Bt848 capture-only card (3x composite, 1x S-VHS)
with 14MHz crystal:
http://www.rainbow-software.org/images/hardware/bt848_.jpg
14MHz PLL was not supported by bttv driver until now.
[mchehab@redhat.com: CodingStyle fixes] Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] mt9p031: Power down the sensor if no supported device has been detected
The mt9p031 driver first accesses the I2C device in its .registered()
method. While doing that it first powers the device up, but if probing
fails, it doesn't power the chip back down. This patch fixes that bug.
* tag 'v3.10-rc1': (11697 commits)
Linux 3.10-rc1
[SCSI] qla2xxx: Update firmware link in Kconfig file.
[SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
[SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
[SCSI] pm80xx: thermal, sas controller config and error handling update
[SCSI] pm80xx: NCQ error handling changes
[SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
[SCSI] pm80xx: Changed module name and debug messages update
[SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
[SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
[SCSI] pm80xx: MSI-X implementation for using 64 interrupts
[SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
[SCSI] pm80xx: Multiple inbound/outbound queue configuration
[SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
[SCSI] lpfc: fix up Kconfig dependencies
[SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
dm cache: set config value
dm cache: move config fns
dm thin: generate event when metadata threshold passed
...
Linus Torvalds [Sun, 12 May 2013 00:04:59 +0000 (17:04 -0700)]
Merge tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing/kprobes update from Steven Rostedt:
"The majority of these changes are from Masami Hiramatsu bringing
kprobes up to par with the latest changes to ftrace (multi buffering
and the new function probes).
He also discovered and fixed some bugs in doing so. When pulling in
his patches, I also found a few minor bugs as well and fixed them.
This also includes a compile fix for some archs that select the ring
buffer but not tracing.
I based this off of the last patch you took from me that fixed the
merge conflict error, as that was the commit that had all the changes
I needed for this set of changes."
* tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/kprobes: Support soft-mode disabling
tracing/kprobes: Support ftrace_event_file base multibuffer
tracing/kprobes: Pass trace_probe directly from dispatcher
tracing/kprobes: Increment probe hit-count even if it is used by perf
tracing/kprobes: Use bool for retprobe checker
ftrace: Fix function probe when more than one probe is added
ftrace: Fix the output of enabled_functions debug file
ftrace: Fix locking in register_ftrace_function_probe()
tracing: Add helper function trace_create_new_event() to remove duplicate code
tracing: Modify soft-mode only if there's no other referrer
tracing: Indicate enabled soft-mode in enable file
tracing/kprobes: Fix to increment return event probe hit-count
ftrace: Cleanup regex_lock and ftrace_lock around hash updating
ftrace, kprobes: Fix a deadlock on ftrace_regex_lock
ftrace: Have ftrace_regex_write() return either read or error
tracing: Return error if register_ftrace_function_probe() fails for event_enable_func()
tracing: Don't succeed if event_enable_func did not register anything
ring-buffer: Select IRQ_WORK
Linus Torvalds [Sat, 11 May 2013 23:19:30 +0000 (16:19 -0700)]
Merge tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- More fixes in the vCPU PVHVM hotplug path.
- Add more documentation.
- Fix various ARM related issues in the Xen generic drivers.
- Updates in the xen-pciback driver per Bjorn's updates.
- Mask the x2APIC feature for PV guests.
* tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Used cached MSI-X capability offset
xen/pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
xen: clear IRQ_NOAUTOEN and IRQ_NOREQUEST
xen: mask x2APIC feature in PV
xen: SWIOTLB is only used on x86
xen/spinlock: Fix check from greater than to be also be greater or equal to.
xen/smp/pvhvm: Don't point per_cpu(xen_vpcu, 33 and larger) to shared_info
xen/vcpu: Document the xen_vcpu_info and xen_vcpu
xen/vcpu/pvhvm: Fix vcpu hotplugging hanging.
Linus Torvalds [Sat, 11 May 2013 22:24:22 +0000 (15:24 -0700)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull second SCSI update from James "Jaj B" Bottomley:
"This is the final round of SCSI patches for the merge window. It
consists mostly of driver updates (bnx2fc, ibmfc, fnic, lpfc,
be2iscsi, pm80xx, qla4x and ipr).
There's also the power management updates that complete the patches in
Jens' tree, an iscsi refcounting problem fix from the last pull, some
dif handling in scsi_debug fixes, a few nice code cleanups and an
error handling busy bug fix."
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (92 commits)
[SCSI] qla2xxx: Update firmware link in Kconfig file.
[SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
[SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
[SCSI] pm80xx: thermal, sas controller config and error handling update
[SCSI] pm80xx: NCQ error handling changes
[SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
[SCSI] pm80xx: Changed module name and debug messages update
[SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
[SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
[SCSI] pm80xx: MSI-X implementation for using 64 interrupts
[SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
[SCSI] pm80xx: Multiple inbound/outbound queue configuration
[SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
[SCSI] lpfc: fix up Kconfig dependencies
[SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
[SCSI] sd: change to auto suspend mode
[SCSI] sd: use REQ_PM in sd's runtime suspend operation
[SCSI] qla4xxx: Fix iocb_cnt calculation in qla4xxx_send_mbox_iocb()
[SCSI] ufs: Correct the expected data transfersize
...
Linus Torvalds [Sat, 11 May 2013 21:29:11 +0000 (14:29 -0700)]
Merge git://git.infradead.org/users/eparis/audit
Pull audit changes from Eric Paris:
"Al used to send pull requests every couple of years but he told me to
just start pushing them to you directly.
Our touching outside of core audit code is pretty straight forward. A
couple of interface changes which hit net/. A simple argument bug
calling audit functions in namei.c and the removal of some assembly
branch prediction code on ppc"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: fix message spacing printing auid
Revert "audit: move kaudit thread start from auditd registration to kaudit init"
audit: vfs: fix audit_inode call in O_CREAT case of do_last
audit: Make testing for a valid loginuid explicit.
audit: fix event coverage of AUDIT_ANOM_LINK
audit: use spin_lock in audit_receive_msg to process tty logging
audit: do not needlessly take a lock in tty_audit_exit
audit: do not needlessly take a spinlock in copy_signal
audit: add an option to control logging of passwords with pam_tty_audit
audit: use spin_lock_irqsave/restore in audit tty code
helper for some session id stuff
audit: use a consistent audit helper to log lsm information
audit: push loginuid and sessionid processing down
audit: stop pushing loginid, uid, sessionid as arguments
audit: remove the old depricated kernel interface
audit: make validity checking generic
audit: allow checking the type of audit message in the user filter
audit: fix build break when AUDIT_DEBUG == 2
audit: remove duplicate export of audit_enabled
Audit: do not print error when LSMs disabled
...
Linus Torvalds [Fri, 10 May 2013 16:27:40 +0000 (09:27 -0700)]
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform drivers from Matthew Garrett:
"Small set of updates, mainly trivial bugfixes and some small updates
to deal with newer hardware.
There's also a new driver that allows qemu guests to notify the
hypervisor that they've just paniced, which seems useful."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
Add support for fan button on Ideapad Z580
pvpanic: pvpanic device driver
asus-nb-wmi: set wapf=4 for ASUSTeK COMPUTER INC. X75A
drivers: platform: x86: Use PTR_RET function
sony-laptop: SVS151290S kbd backlight and gfx switch support
hp-wmi: add more definitions for new event_id's
dell-laptop: Fix krealloc() misuse in parse_da_table()
hp_accel: Ignore the error from lis3lv02d_poweron() at resume
dell: add new dell WMI format for the AIO machines
projects / linux-beck.git / log