Matt Carlson [Fri, 15 Aug 2008 21:08:22 +0000 (14:08 -0700)]
tg3: Preserve register settings for DASH
Broadcom's DASH (Desktop and mobile Architecture for System Hardware)
implementation requires that the driver preserve particular register
settings. If the driver does not preserve them, communication with
the DASH firmware will be lost.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 15 Aug 2008 21:07:51 +0000 (14:07 -0700)]
tg3: Refine APE status check
Recently, more status bits have been added to the APE status register.
This patch refines the status register check so that the driver can
send more events than it would have otherwise.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 15 Aug 2008 21:07:24 +0000 (14:07 -0700)]
tg3: Add APE register access locking
If the driver resets the chip while the APE is performing a register
access, that register access will never complete and the APE will hang
indefinitely. To prevent this race condition, the driver must acquire
an APE mutex before resetting the chip. The APE will not attempt a
register access until it acquires this lock.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 15 Aug 2008 20:44:31 +0000 (13:44 -0700)]
ipv4: Disable route secret interval on zero interval
Let me first state that disabling the route cache hash rebuild
should not be done without extensive analysis on the risk profile
and careful deliberation.
However, there are times when this can be done safely or for
testing. For example, when you have mechanisms for ensuring
that offending parties do not exist in your network.
This patch lets the user disable the rebuild if the interval is
set to zero. This also incidentally fixes a divide-by-zero error
with name-spaces.
In addition, this patch makes the effect of an interval change
immediate rather than it taking effect at the next rebuild as
is currently the case.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Fri, 15 Aug 2008 00:01:10 +0000 (17:01 -0700)]
pkt_sched: Fix unlocking in tc_ctl_tfilter()
Fix a bug with spin_lock_bh() inserted instead of spin_unlock_bh() by
some recent patch.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Brian Haley [Thu, 14 Aug 2008 22:33:21 +0000 (15:33 -0700)]
netns: Add network namespace argument to rt6_fill_node() and ipv6_dev_get_saddr()
ipv6_dev_get_saddr() blindly de-references dst_dev to get the network
namespace, but some callers might pass NULL. Change callers to pass a
namespace pointer instead.
Signed-off-by: Brian Haley <brian.haley@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 14 Aug 2008 22:30:14 +0000 (15:30 -0700)]
bnx2: Reinsert VLAN tag when necessary.
In certain cases when ASF or other management firmware is running, the
chip may be configured to always strip out the VLAN tag even when
VLAN acceleration is not enabled. This causes some VLAN tagged
packets to be received by the host stack without any knowledge that
the original packet was VLAN tagged.
We fix this by re-inserting the VLAN tag into the packet when necessary.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 14 Aug 2008 22:29:39 +0000 (15:29 -0700)]
bnx2: Use proper CONFIG_VLAN_8021Q to compile the VLAN code.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 14 Aug 2008 22:29:09 +0000 (15:29 -0700)]
bnx2: Fix logic to setup VLAN rx tagging.
We should now be checking BNX2_FLAG_CAN_KEEP_VLAN to determine how
to set the VLAN rx tagging in the RX_MODE register.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Brownell [Fri, 8 Aug 2008 20:53:29 +0000 (13:53 -0700)]
Kconfig: HSO driver bugfixes and updates
Move the Kconfig for the new "Option" driver so it's not in the
middle of the usbnet-based drivers, so the dependency displays
in the Kconfig user interfaces don't get trashed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Arjan van de Ven <arjan@infradead.org> Cc: Andrew Bird <ajb@spheresystems.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Olivier Blin [Fri, 8 Aug 2008 19:01:41 +0000 (12:01 -0700)]
hso: fix refcounting on the ttyHSx devices
The references on ttyHSx devices were not decremented correctly when
the tty was closed. The helper freeing the serial devices was never
called because of that, and the module left some dangling sysfs
devices after being unloaded.
Signed-off-by: Olivier Blin <blino@mandriva.com> Cc: Jari Tenhunen <jari.tenhunen@iki.fi> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Adrian Bunk [Fri, 8 Aug 2008 18:33:34 +0000 (21:33 +0300)]
[netdrvr] uninline atl1e_setup_mac_ctrl()
There doesn't seem to be a compelling reason why atl1e_setup_mac_ctrl()
is marked as "inline":
It's not used in any place where speed would matter much, and as long as
it has only one caller non-ancient gcc versions anyway inline it
automatically.
This patch fixes the following compile error with gcc 3.4:
<-- snip -->
...
CC drivers/net/atl1e/atl1e_main.o
atl1e_main.c: In function `atl1e_check_link':
atl1e_main.c:50: sorry, unimplemented: inlining failed in call to
atl1e_main.c:196: sorry, unimplemented: called from here
make[4]: *** [drivers/net/atl1e/atl1e_main.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For NX3031 mac addr should be read from firmware. mac addr in flash
is still valid, but can be overridden by firmware if running in
virtualization environment.
For old revisions, mac addr is retrieved directly from flash.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:36:16 +0000 (18:36 -0700)]
e1000e: remove unnecessary snippet missed in prior check_options update
The removal of this bit of code was missed in an earlier patch submittal.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:36:11 +0000 (18:36 -0700)]
e1000e: test for unusable MSI support
Some systems do not like 82571/2 use of 16-bit MSI messages and some
other systems claim to support MSI, but neither really works. Setup a
test MSI handler to detect whether or not MSI is working properly, and
if not, fallback to legacy INTx interrupts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:36:06 +0000 (18:36 -0700)]
e1000e: increase minimum frame size allowed
Setting an MTU value below 68 was disabling the network connection and
would not reconnect until the driver was reloaded. Prevent changing the
MTU to anything below 68.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:36:01 +0000 (18:36 -0700)]
e1000e: Increase Tx timeout factor for 10Mbps
Prevent Tx hangs from happening on 10Mb flood ping by increasing the
timeout factor.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:35:56 +0000 (18:35 -0700)]
e1000e: Use skb_copy_to_linear_data_offset introduced in 2.6.22
The e1000e driver was based on a version of e1000 prior to acme's
introduction of skb_copy_to_linear_data_offset, and was submitted
after acme went through and coverted all the drivers to use it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:35:51 +0000 (18:35 -0700)]
e1000e: Set InterruptThrottleRate to default when invalid value used
During module load, seting the InterruptThrottleRate parameter to an
invalid value would result in the itr/itr_setting pair being set to
unexpected values which would result in poor performance.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Sat, 9 Aug 2008 01:35:44 +0000 (18:35 -0700)]
e1000e: Return 1 instead of a non-zero value for link up indication
A number of users have mentioned they have tools that rely on a link-up
indication having a return value of 1 rather than a non-zero value.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
tlan: Fix two regressions introduced by 64bit conversion.
Two regressions were introduced by the recent tlan: 64bit conversion
commit (93e16847c9db0093065c98063cfc639cdfccf19a). The first in
TLan_GetSKB caused a NULL pointer dereference. With the second causing
the link to fail to come up.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sky2: Fix suspend/hibernation/shutdown regression with WOL enabled (rev. 2)
On my test box with the Asus M3A32-MVP main board there is a
regression from 2.6.26 related to suspend, hibernation and
shutdown. Namely, if Wake-on-LAN is enabled with
'ethtool -s eth0 wol g', the box hangs solid during all of these
operations, while executing either sky2_suspend(), or
sky2_shutdown(). This patch fixes it for me.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The arm ixp4xx_eth driver doesn't compile in 2.6.27-rc1:
CC [M] drivers/net/arm/ixp4xx_eth.o
drivers/net/arm/ixp4xx_eth.c: In function 'eth_poll':
drivers/net/arm/ixp4xx_eth.c:554: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast
drivers/net/arm/ixp4xx_eth.c:554: error: too few arguments to function 'dma_mapping_error'
drivers/net/arm/ixp4xx_eth.c: In function 'eth_xmit':
drivers/net/arm/ixp4xx_eth.c:701: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast
drivers/net/arm/ixp4xx_eth.c:701: error: too few arguments to function 'dma_mapping_error'
drivers/net/arm/ixp4xx_eth.c: In function 'init_queues':
drivers/net/arm/ixp4xx_eth.c:886: warning: passing argument 1 of 'dma_mapping_error' makes pointer from integer without a cast
drivers/net/arm/ixp4xx_eth.c:886: error: too few arguments to function 'dma_mapping_error'
make[3]: *** [drivers/net/arm/ixp4xx_eth.o] Error 1
make[2]: *** [drivers/net/arm] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
dma_mapping_error() changed in 2.6.27-rc1 to also take a device parameter,
but nobody bothered updating ixp4xx_eth.c. Fixed by passing the appropriate
device value in the dma_mapping_error() calls.
Tested on an ixp425 box.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Acked-by: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Scott Wood [Tue, 12 Aug 2008 20:10:46 +0000 (15:10 -0500)]
gianfar: Call gfar_halt_nodisable() from gfar_halt().
gfar_halt() was factored out into halting and disabling by commit d87eb12785c14de1586e3bad86ca2c0991300339, as the suspend() method
only wants to do the former. However, the call to gfar_halt_nodisable()
from gfar_halt() apparently got lost during the patch respin process.
This adds it back.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Huang Weiyi [Mon, 11 Aug 2008 04:56:44 +0000 (12:56 +0800)]
[netdrvr] remove unnecessary #include
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/acenic.c
drivers/net/bnx2x_link.c
drivers/net/bnx2x_main.c
drivers/net/cpmac.c
drivers/net/gianfar_sysfs.c
drivers/net/ipg.h
drivers/net/ppp_mppe.c
drivers/net/pppol2tp.c
drivers/net/r6040.c
drivers/net/sh_eth.c
drivers/net/sky2.c
drivers/net/tehuti.h
drivers/net/typhoon.c
This patch removes the said #include <linux/version.h>.
Signed-off-by: Huang Weiyi <hwy@cn.fujitsu.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (47 commits)
usb: musb: pass configuration specifics via pdata
usb: musb: fix hanging when rmmod gadget driver
USB: Add MUSB and TUSB support
USB: serial: remove CONFIG_USB_DEBUG from sierra and option drivers
USB: Add vendor/product id of ZTE MF628 to option
USB: quirk PLL power down mode
USB: omap_udc: fix compilation with debug enabled
usb: cdc-acm: drain writes on close
usb: cdc-acm: stop dropping tx buffers
usb: cdc-acm: bugfix release()
usb gadget: issue notifications from ACM function
usb gadget: remove needless struct members
USB: sh: r8a66597-hcd: fix disconnect regression
USB: isp1301: fix compilation
USB: fix compiler warning fix
usb-storage: unusual_devs entry for Nokia 5300
USB: cdc-acm.c: Fix compile warnings
USB: BandRich BandLuxe C150/C250 HSPA Data Card Driver
USB: ftdi_sio: add support for PHI Fisco data cable (FT232BM based, VID/PID 0403:e40b)
usb: isp1760: don't be noisy about short packets.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
netns: Fix crash by making igmp per namespace
bnx2x: Version update
bnx2x: Checkpatch compliance
bnx2x: Spelling mistakes
bnx2x: Minor code improvements
bnx2x: Driver info
bnx2x: 1G LED does not turn off
bnx2x: 8073 PHY changes
bnx2x: Change GPIO for any port
bnx2x: Pause settings
bnx2x: Link order with external PHY
bnx2x: No LRO without Rx checksum
bnx2x: Wrong structure size
bnx2x: WoL capability
bnx2x: Clearing MAC addresses filters
bnx2x: Delay in while loops
bnx2x: PBA Table Page Alignment Workaround
bnx2x: Self-test false positive
bnx2x: Memory allocation
bnx2x: HW attention lock
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Handle stack trace attempts before irqstacks are setup.
sparc64: Implement IRQ stacks.
sparc: remove include of linux/of_device.h from asm/of_device.h
sparc64: Fix recursion in stack overflow detection handling.
sparc/drivers: use linux/of_device.h instead of asm/of_device.h
sparc64: Don't MAGIC_SYSRQ ifdef smp_fetch_global_regs and support code.
Felipe Balbi [Mon, 4 Aug 2008 10:53:52 +0000 (13:53 +0300)]
usb: musb: fix hanging when rmmod gadget driver
If we try to modprobe a second gadget driver before
rmmoding the first one, the reference for the first
gadget driver would get NULLed avoiding usb to change
gadget drivers later.
Cc: David Brownell <david-b@pacbell.net> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: serial: remove CONFIG_USB_DEBUG from sierra and option drivers
These drivers should not be relying on CONFIG_USB_DEBUG. By doing this,
it prevents users of kernels that do not enable this option from
enabling debugging in these drivers, unlike all other usb-serial
drivers.
Oliver Martin [Sat, 9 Aug 2008 02:49:26 +0000 (04:49 +0200)]
USB: Add vendor/product id of ZTE MF628 to option
This adds the vendor and product id (19d2:0015) of the ZTE MF628 HSDPA
modem to the option driver. It still needs a mode switch command issued
beforehand, this is currently handled by a userspace tool.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Libin Yang [Fri, 8 Aug 2008 07:03:31 +0000 (15:03 +0800)]
USB: quirk PLL power down mode
On some AMD 700 series southbridges, ISO OUT transfers (such as audio
playback through speakers) on the USB OHCI controller may be corrupted
when an A-Link express power saving feature is active.
PLL power down mode in conjunction with link power management feature
L1 being enabled is the bad combination ... this patch prevents them
from being enabled when ISO transfers are pending.
Signed-off-by: Crane Cai <crane.cai@amd.com> Signed-off-by: Libin Yang <libin.yang@amd.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 7 Aug 2008 01:46:10 +0000 (18:46 -0700)]
usb: cdc-acm: drain writes on close
Add a mechanism to let the write queue drain naturally before
closing the TTY, rather than always losing that data. There
is a timeout, so it can't wait too long.
Provide missing locking inside acm_wb_is_avail(); it matters
more now. Note, this presumes an earlier patch was applied,
removing a call to this routine where the lock was held.
Slightly improved diagnostics on write URB completion, so we
can tell when a write URB gets killed and, if so, how much
data it wrote first ... and so that I/O path is normally
silent (and can't much change timings).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 7 Aug 2008 01:44:12 +0000 (18:44 -0700)]
usb: cdc-acm: stop dropping tx buffers
The "increase cdc-acm write throughput" patch left in place two
now-obsolete mechanisms, either of which can make the cdc-acm
driver drop TX data (nasty!). This patch removes them:
- The write_ready flag ... if an URB and buffer were found,
they can (and should!) always be used.
- TX path acm_wb_is_used() ... used when the buffer was just
allocated, so that check is pointless.
Also fix a won't-yet-matter leak of a write buffer on a disconnect path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Engraf <david.engraf@netcom.eu> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 7 Aug 2008 01:49:57 +0000 (18:49 -0700)]
usb gadget: issue notifications from ACM function
Update the CDC-ACM gadget code to support the peripheral-to-host
notifications when the tty is opened or closed, or issues a BREAK.
The serial framework code calls new generic hooks; right now only
CDC-ACM uses those hooks. This resolves several REVISIT comments
in the code. (Based on a patch from Felipe Balbi.)
Note that this doesn't expose USB_CDC_CAP_BRK to the host, since
this code still rejects USB_CDC_REQ_SEND_BREAK control requests
for host-to-peripheral BREAK signaling (received via /dev/ttyGS*).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 7 Aug 2008 17:02:40 +0000 (13:02 -0400)]
usb-storage: unusual_devs entry for Nokia 5300
This patch (as1120) adds an unusual_devs entry for the Nokia 5300.
Maybe once Nokia releases the Symbian code we'll be able to fix all
the problems it has with the USB mass-storage protocol.
CC [M] drivers/usb/class/cdc-acm.o
drivers/usb/class/cdc-acm.c: In function 'acm_waker':
drivers/usb/class/cdc-acm.c:527: warning: comparison of distinct pointer types lacks a cast
drivers/usb/class/cdc-acm.c:529: warning: comparison of distinct pointer types lacks a cast
Lex Ross [Wed, 6 Aug 2008 12:25:08 +0000 (16:25 +0400)]
USB: ftdi_sio: add support for PHI Fisco data cable (FT232BM based, VID/PID 0403:e40b)
Support for PHI Fisco USB to Serial data cable (FTDI FT232BM based).
PHI Fisco cable is supplied for connecting Philips Xenium 9@9++ mobile phones.
PIDs were missing.
Tested successfully with PHI Fisco Data Cable (VID/PID 0403:e40b)
Signed-off-by: Lex V. Ross <lross@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to Alan Stern, short packets are quite normal under
certain circumstances. This printk was triggered by usb to
serial converters on every packet and some usb sticks triggered
a few of those while plugging the stick.
This printks are now hidden unless USB debug mode is activated.
Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ISP1760 requires a delay of 90ns between programming the address and
reading the data. Current driver solves this by a mdelay(1) which is
very heavy weighted and slow. This patch applies the workaround from
the ISP1760 FAQ by using two different banks for PTD and payload data
and using a common wait for them. This wait is done by an additional
ISP1760 access (whose timing constraints guarantee the 90ns delay).
This improves speed when reading from an USB stick from:
$ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
real 1m 15.43s
user 0m 0.44s
sys 0m 39.46s
to
$ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
real 0m 18.53s
user 0m 0.16s
sys 0m 12.97s
[bigeasy@linutronix.de: fixed comment formating, moved define into
header file, obey 80 char rule]
usb: return error code instead of 0 in the enqueue function.
if the enqueue function returns -ESHUTDOWN or -ENOMEM then
we return 0 instead of an error. This leads to a timeout and
then to a dequeue request of an not enqueued urb.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 7 Jul 2008 19:16:08 +0000 (12:16 -0700)]
USB: serial gadget: rx path data loss fixes
Update RX path handling in new serial gadget code to cope better with
RX blockage: queue every RX packet until its contents can safely be
passed up to the ldisc. Most of the RX path work is now done in the
RX tasklet, instead of just the final "push to ldisc" step. This
addresses some cases of data loss:
- A longstanding serial gadget bug: when tty_insert_flip_string()
didn't copy the entire buffer, the rest of the characters were
dropped! Now that packet stays queued until the rest of its data
is pushed to the ldisc.
- Another longstanding issue: in the unlikely case that an RX
transfer returns data and also reports a fault, that data is
no longer discarded.
- In the recently added RX throttling logic: it needs to stop
pushing data into the TTY layer, instead of just not submitting
new USB read requests. When the TTY is throttled long enough,
backpressure will eventually make the OUT endpoint NAK.
Also: an #ifdef is removed (no longer necessary); and start switching
to a better convention for debug messages (prefix them with tty name).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kevin Lloyd [Thu, 10 Jul 2008 21:14:57 +0000 (14:14 -0700)]
USB Storage Sierra: TRU-Install feature update
This patch upgrades the support for the Sierra Wireless TRU-Install
feature (i.e. zeroCD) to allow for future support of Linux enabled
TRU-Install devices.
By default all devices that do not have a Linux enabled TRU-Install
device (i.e. the device does not have a Linux package on the virtual CD
partition) will be switched into "modem mode." Devices that do contain a
Linux package in the TRU-Install virtual CD will be allowed to enumerate
as a CD-Rom so that either (a) a user can install the packaged software
or (b) a user-space application (e.g. udev) can switch it to modem mode.
This patch does allow for manual override by adding a usb-storage module
parameter 'swi_tru_install' which can force the modem into either mode
regardless of what packages it contains.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kevin Lloyd [Thu, 10 Jul 2008 21:14:51 +0000 (14:14 -0700)]
USB Serial Sierra: Dynamic interface detection
This patch changes the method by which the number of ports per interface is
assigned so that it is more dynamic and calculated on the fly (as opposed to
hard coding it). This will allow for faster and easier addition of products.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 21 Jul 2008 14:08:28 +0000 (10:08 -0400)]
usb-storage: unusual_devs entries for iRiver T10 and Datafab CF+SM reader
This patch (as1115) adds unusual_devs entries with the IGNORE_RESIDE
flag for the iRiver T10 and the Simple Tech/Datafab CF+SM card
reader. Apparently these devices provide reasonable residue values
for READ and WRITE operations, but not for others like INQUIRY or READ
CAPACITY.
This fixes the iRiver T10 problem reported in Bugzilla #11125.
Simon Arlott [Mon, 21 Jul 2008 19:44:50 +0000 (20:44 +0100)]
USB: Move usb/mon/ up to misc options in Kconfig
This makes "USB Monitor" appear under "Miscellaneous USB options"
section instead of in the middle of device specific drivers in the
"USB Imaging devices" section.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 29 Jul 2008 15:58:06 +0000 (11:58 -0400)]
usb-storage: automatically recognize bad residues
This patch (as1119) will help to reduce the clutter of usb-storage's
unusual_devs file by automatically detecting some devices that need
the IGNORE_RESIDUE flag. The idea is that devices should never return
a non-zero residue for an INQUIRY or a READ CAPACITY command unless
they failed to transfer all the requested data. So if one of these
commands transfers a standard amount of data but there is a positive
residue, we know that the residue is bogus and we can set the flag.
This fixes the problems reported in Bugzilla #11125.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 Jul 2008 15:31:50 +0000 (11:31 -0400)]
USB: fix interface unregistration logic
This patch (as1122) fixes a bug: When an interface is unregistered,
its children (sysfs files and endpoint devices) are unregistered after
it instead of before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Kay Sievers <kay.sievers@vrfy.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 29 Jul 2008 16:01:04 +0000 (12:01 -0400)]
usb-serial: don't release unregistered minors
This patch (as1121) fixes a bug in the USB serial core. When a device
is unregistered, the core will give back its minors -- even if the
device hasn't been assigned any!
The patch reserves the highest minor value (255) to mean that no minor
was assigned. It also removes some dead code and does a small style
fixup.
Dave Jones [Mon, 14 Jul 2008 17:28:34 +0000 (13:28 -0400)]
USB: usb-storage: quirk around v1.11 firmware on Nikon D4
usb-storage: quirk around v1.11 firmware on Nikon D40
https://bugzilla.redhat.com/show_bug.cgi?id=454028
Just as in earlier firmware versions, we need to perform this
quirk for the latest version too.
Speculatively do the entry for the D80 too, as they seem to
have the same firmware problems historically.
Signed-off-by: Dave Jones <davej@redhat.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 21 Jul 2008 13:56:26 +0000 (09:56 -0400)]
USB: OHCI: fix system hang caused by earlier patch
This patch (as1114) fixes a problem that was revealed by an earlier
patch (as1069b). Some broken controllers seem never to turn off their
RHCS interrupt status bit, even when told to do so. As a result they
generate an interrupt storm and hang the system.
The patch avoids enabling RHSC interrupt requests when the RHCS status
bit is already set. This should have no adverse affects on normal
controllers, since they won't set the status bit until a root-hub
status change actually occurs, in which case we wouldn't enable RHSC
interrupt requests anyway -- we would wait until the status change had
been processed and cleared.
David Brownell [Sat, 26 Jul 2008 15:06:24 +0000 (08:06 -0700)]
USB: fix USB boot crash, ecm_do_notify(), list_add corruption. prev->next should be next (ffff88003b8f82f8)
This fixes a BUG() turned up by Ingo via randconfig testing, where
CONFIG_LIST_DEBUG turned up list corruption. The corruption was
caused by the dummy_hcd (single-machine test harness for gadget and
HCD code) trashing the request queue when driven by the new CDC
composite gadget an I/O pattern that was previously uncommon.
Fix suggested by Alan Stern.
Wolfgang Mües [Tue, 29 Jul 2008 09:54:43 +0000 (11:54 +0200)]
usb: auerswald: remove driver (obsolete)
This patch removes the auerswald USB driver from the linux kernel
2.6.26.
This driver was included into the kernel mainly to connect to the ISDN
framework. This was done in linux 2.4.x. For 2.6.x, due to the fragile
and moving ISDN support, this connection was never realized, and the
only use of this driver was for device configuration. In the age of DSL,
the demand of ISDN support is getting very low.
Meanwhile, with the advent of libusb, an userspace driver was done for
the device configuration which works fine for linux and mac. (Thanks to
the libusb developers!). The userspace driver is downloadable from the
auerswald web site.
So this driver is obsolete now and has to be removed. Many thanks to all
developers which helped me to bring this driver up and working.
Signed-off-by: Wolfgang Muees <wolfgang@iksw-muees.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Howells [Wed, 13 Aug 2008 15:20:04 +0000 (16:20 +0100)]
CRED: Introduce credential access wrappers
The patches that are intended to introduce copy-on-write credentials for 2.6.28
require abstraction of access to some fields of the task structure,
particularly for the case of one task accessing another's credentials where RCU
will have to be observed.
Introduced here are trivial no-op versions of the desired accessors for current
and other tasks so that other subsystems can start to be converted over more
easily.
Wrappers are introduced into a new header (linux/cred.h) for UID/GID,
EUID/EGID, SUID/SGID, FSUID/FSGID, cap_effective and current's subscribed
user_struct. These wrappers are macros because the ordering between header
files mitigates against making them inline functions.
linux/cred.h is #included from linux/sched.h.
Further, XFS is modified such that it no longer defines and uses parameterised
versions of current_fs[ug]id(), thus getting rid of the namespace collision
otherwise incurred.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: James Morris <jmorris@namei.org>
Daniel Lezcano [Wed, 13 Aug 2008 23:15:57 +0000 (16:15 -0700)]
netns: Fix crash by making igmp per namespace
This patch makes the multicast socket to be per namespace.
When a network namespace is created, other than the init_net and a
multicast packet is received, the kernel goes to a hang or a kernel panic.
How to reproduce ?
* create a child network namespace
* create a pair virtual device veth
* ip link add type veth
* move one side to the pair network device to the child namespace
* ip link set netns <childpid> dev veth1
* ping -I veth0 224.0.0.1
The bug appears because the function ip_mc_init_dev does not initialize
the different multicast fields as it exits because it is not the init_net.
BUG: soft lockup - CPU#0 stuck for 61s! [avahi-daemon:2695]
Modules linked in:
irq event stamp: 50350
hardirqs last enabled at (50349): [<c03ee949>] _spin_unlock_irqrestore+0x34/0x39
hardirqs last disabled at (50350): [<c03ec639>] schedule+0x9f/0x5ff
softirqs last enabled at (45712): [<c0374d4b>] ip_setsockopt+0x8e7/0x909
softirqs last disabled at (45710): [<c03ee682>] _spin_lock_bh+0x8/0x27
Eilon Greenstein [Wed, 13 Aug 2008 22:58:49 +0000 (15:58 -0700)]
bnx2x: Minor code improvements
Minor code improvements
Small changes to make the code a little bit more efficient and mostly
more readable:
- Using unified macros for EMAC_RD/WR which looks like normal REG_RD/WR
- Removing the NIG_WR since it did nothing and was only confusing
- On bnx2x_panic_dump, print only the used parts of the rings
- define parameters only on the branch they are needed and not at the
beginning of the function
- using NETIF_MSG_INTR and not private BNX2X_MSG_SP for debug prints
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Wed, 13 Aug 2008 22:58:30 +0000 (15:58 -0700)]
bnx2x: Driver info
Driver info
The internal FW which is downloaded by the driver should not be
displayed - it is only causing confusion and it is redundant since it
can be concluded from the driver version. Display only FW which is
burned on the board nvram
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log