usb: musb: omap: add usb_phy_init in omap2430_musb_init
Some PHYs load too early (twl4030) making omap glue to miss cable connect events
if the board is booted with cable connected. So adding usb_phy_init in
omap2430_musb_init lets PHYs to report events once glue is ready.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Bhupesh Sharma [Fri, 1 Mar 2013 19:46:31 +0000 (20:46 +0100)]
usb: gadget: uvc: Make video streaming buffer size comply with USB3.0 SS
As per the USB3.0 specs, the bandwidth requirements of a UVC's video
streaming endpoint will change to support super-speed. These changes
will be dependent on whether the UVC video streaming endpoint is Bulk or
Isochronous:
- If video streaming endpoint is Isochronous:
As per Section 4.4.8.2 (Isochronous Transfer Bandwidth Requirements)
of the USB3.0 specs:
A SuperSpeed isochronous endpoint can move up to three burst
transactions of up to 16 maximum sized packets (3 * 16 * 1024 bytes)
per service interval.
- If video streaming endpoint is Bulk:
As per 4.4.6.1 (Bulk Transfer Data Packet Size) of the USB3.0 specs:
An endpoint for bulk transfers shall set the maximum data packet
payload size in its endpoint descriptor to 1024 bytes. It also
specifies the burst size that the endpoint can accept from or
transmit on the SuperSpeed bus. The allowable burst size for a bulk
endpoint shall be in the range of 1 to 16.
So, in the Isochronous case, we can define the USB request's buffer to
be equal to = (Maximum packet size) * (bMaxBurst + 1) * (Mult + 1), so
that the UDC driver can try to send out this buffer in one Isochronous
service interval.
The same computation will hold good for the Bulk case as the Mult
value is 0 here and we can have a USB request buffer of maximum
16 * 1024 bytes size, which can be sent out by the UDC driver as
per the Bulk bandwidth allocation on the USB3 bus.
This patch adds the above-mentioned support and is also USB2.0 backward
compliant.
Bhupesh Sharma [Fri, 1 Mar 2013 19:46:30 +0000 (20:46 +0100)]
usb: gadget: uvc: Delay the status stage when setting alternate setting 1
This patch adds the support in UVC webcam gadget design for providing
USB_GADGET_DELAYED_STATUS in response to a set_interface(alt setting 1)
command issue by the Host.
The current UVC webcam gadget design generates a STREAMON event
corresponding to a set_interface(alt setting 1) command from the Host.
This STREAMON event will eventually be routed to a real V4L2 device.
To start video streaming, it may be required to perform some register
writes to a camera sensor device over slow external busses like I2C or
SPI. So, it makes sense to ensure that we delay the STATUS stage of the
set_interface (alt setting 1) command.
Otherwise, a lot of ISOC IN tokens sent by the Host will be replied to
by zero-length packets by the webcam device. On certain Hosts this may
even lead to ISOC URBs been cancelled from the Host side.
So, as soon as we finish doing all the "streaming" related stuff on the
real V4L2 device, we call a STREAMON ioctl on the UVC side and from here
we call the 'usb_composite_setup_continue' function to complete the
status stage of the set_interface(alt setting 1) command.
Further, we need to ensure that we queue no video buffers on the UVC
webcam gadget, until we de-queue a video buffer from the V4L2 device.
So, the application should call the STREAMON on UVC side only when it
has dequeued sufficient buffers from the V4L2 side and queued them to
the UVC gadget.
Bhupesh Sharma [Fri, 1 Mar 2013 19:46:29 +0000 (20:46 +0100)]
usb: gadget: uvc: Add fix for UVC compliance test suite's assertion 6.1.25 failure
As per the UVC compliance test suite's assertion 6.1.25, the `iFunction`
field of the Interface Association Descriptor (IAD) should the match the
`iInterface` field of the standard Video Control (VC) Interface Descriptor for
this Video Interface Collection (VIC).
This mandatory case is captured in section 3.11 of the
USB Video Class Compliance specification revision 1.1
This patch fixes this test assertion's failure and has been tested on
Linux FC16, WinXP, WIN7 and WIN8 High speed and Super Speed hosts
for successful enumeration.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
[Merged the association and control string descriptors] Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Bhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Bhupesh Sharma [Fri, 1 Mar 2013 19:46:28 +0000 (20:46 +0100)]
usb: gadget: uvc: Add fix for UVC compliance test suite assertion 6.3.90 failure
As per UVC compliance test specification's assertion number 6.3.90
related to 'Standard VS Isochronous Video Data Endpoint Descriptor Assertions',
the bits D3..2 of 'bmAttributes' field of Standard VS Isochronous Video Data
Endpoint Descriptor should be 01 (binary) to indicate that the
synchronization type is ASYNCHRONOUS.
This mandatory requirement has been captured in section 3.10.1.1 of the UVC
Video Class Specification version 1.1
Vivek Gautam [Thu, 14 Mar 2013 10:29:10 +0000 (15:59 +0530)]
usb: phy: samsung: Common out the generic stuff
Moving register and structure definitions to header file,
and keeping the generic functions to be used across
multiple PHYs in common phy helper driver under SAMSUNG_USBPHY,
and moving USB 2.0 PHY driver under SAMSUNG_USB2PHY.
Also allowing samsung PHY drivers be built as modules.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
*dma_mask* is not set for devices created from dt data. So filled dma_mask
for dwc3_omap device here. And dwc3 core will copy the dma_mask from its
parent.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Chen Gang [Mon, 11 Mar 2013 10:28:02 +0000 (18:28 +0800)]
usb: gadget: s3c-hsudc: delete outdated comment
since commit d93e260 (usb: gadget: s3c-hsudc: use udc_start and udc_stop
functions) the 'driver' parameter has been deleted from
s3c_hsudc_stop_activity() but its documentation was left outdated. This
patch deletes the comment since it makes no sense anymore.
Signed-off-by: Chen Gang <gang.chen@asianux.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Felipe Balbi [Fri, 8 Mar 2013 11:22:58 +0000 (13:22 +0200)]
usb: phy: introduce ->set_vbus() method
this method will be used to enable or disable
the charge pump.
Whenever we have DRD devices, we need to be
able to turn VBUS on or off whenever we want.
Note that in the ideal case, this would be
controlled by the ID-pin Interrupt, but not
all devices have ID-pin properly routed since
manufacturers can choose to save that trace
if they're building a host-only product out
of a DRD IP.
This is also useful during debugging where
we might not have the proper cable hanging
around.
Felipe Balbi [Thu, 7 Mar 2013 08:45:56 +0000 (10:45 +0200)]
usb: otg: move usb_otg_state_string to usb-common.c
otg.c only had a single function definition
which might make more sense to be placed in
usb-common.c. While doing that, we also delete
otg.c since it's now empty.
Fabio Baltieri [Wed, 20 Feb 2013 08:53:39 +0000 (09:53 +0100)]
usb: musb: drop dangling CONFIG_USB_MUSB_DEBUG
CONFIG_USB_MUSB_DEBUG option was removed in
5c8a86e usb: musb: drop unneeded musb_debug trickery
to cleanup the code from driver specific debug facilities. This patch
drops the last references to the musb debug config option,
unconditionally enabling all debug code paths, thus letting that code
being dropped at compile time if not needed.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
Vivek Gautam [Sat, 2 Mar 2013 13:25:24 +0000 (18:55 +0530)]
usb: dwc3: set 'mode' based on selected Kconfig choices
Now that machines may select dwc3's working mode (HOST only,
GADGET only or DUAL_ROLE) via Kconfig, let's set dwc3's mode
based on that, rather than fixing it to whatever hardware
says.
This way we can skip initializing Gadget/Host in case
we are using Host-only/Gadget-only mode respectively.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: phy: mxs: use readl(), writel() instead of the _relaxed() versions
This patch converts the mxs-phy driver from readl_relaxed(), writel_relaxed()
to the plain readl(), writel() functions, which are available on all platforms.
This is done to enable compile time testing on non ARM platforms.
Reported-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
In DWC3 versions < 2.50a configured without
Hibernation mode enabled, there will be an
extra link status change interrupt if device
detects host-initiated U3 exit.
In that case, core will generate an unnecessary
U3 -> RESUME transition which should be ignored
by the driver.
not all UDC drivers need a proper release function,
for those which don't need it, we udc-core will provide
a no-op release method so we can remove "redefinition"
of such methods in almost every UDC driver.
projects / linux-beck.git / log