Upon rmmod, the <debugfs>/ieee80211/phyX dir is being removed.
later, we try to remove <debugfs>/ieee80211/phyX/wl12xx, which
might result in NULL dereference.
Remove the excessive debugfs_remove_recursive() call.
(consequently, there is no more need to save wl->rootdir)
Felix Fietkau [Thu, 20 Jan 2011 20:57:30 +0000 (21:57 +0100)]
ath9k: remove a bogus error message
When beacons are being added or removed for an interface, ieee80211_beacon_get
will sometimes not return a beacon. This is normal and should not result in
useless logspam.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 19 Jan 2011 09:21:13 +0000 (18:21 +0900)]
ath5k: Remove redundant sc->curband
Remove sc->curband because the band is already stored in the current channel.
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 19 Jan 2011 09:21:08 +0000 (18:21 +0900)]
ath5k: Remove unused sc->curmode
sc->curmode is set but never used. Remove it and the helper function. Also the
ath5k_rate_update which is refered to in the comment does not exist (any more?)
so we don't need to setup the band in that place.
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 19 Jan 2011 09:21:02 +0000 (18:21 +0900)]
ath5: Remove unused CTL definitions
They are unused in ath5k and a more detailled definition is in
ath/regd_common.h.
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 19 Jan 2011 09:20:57 +0000 (18:20 +0900)]
ath5k: Add 802.11j 4.9GHz channels to allowed channels
Add the 802.11j (20MHz channel width) channels to the allowed channels. This
still does not enable 802.11j in ath5k since these frequencies are out of the
configured range. A later patch will deal with that.
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 19 Jan 2011 09:20:47 +0000 (18:20 +0900)]
ath5k: Rename ath5k_copy_channels
Rename ath5k_copy_channels() to ath5k_setup_channels() - nothing is copied
here.
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Mon, 17 Jan 2011 04:37:28 +0000 (13:37 +0900)]
cfg80211: Extend channel to frequency mapping for 802.11j
Extend channel to frequency mapping for 802.11j Japan 4.9GHz band, according to
IEEE802.11 section 17.3.8.3.2 and Annex J. Because there are now overlapping
channel numbers in the 2GHz and 5GHz band we can't map from channel to
frequency without knowing the band. This is no problem as in most contexts we
know the band. In places where we don't know the band (and WEXT compatibility)
we assume the 2GHz band for channels below 14.
This patch does not implement all channel to frequency mappings defined in
802.11, it's just an extension for 802.11j 20MHz channels. 5MHz and 10MHz
channels as well as 802.11y channels have been omitted.
The following drivers have been updated to reflect the API changes:
iwl-3945, iwl-agn, iwmc3200wifi, libertas, mwl8k, rt2x00, wl1251, wl12xx.
The drivers have been compile-tested only.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: Brian Prodoehl <bprodoehl@gmail.com> Acked-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Mon, 10 Jan 2011 07:11:49 +0000 (23:11 -0800)]
ath9k: Keep track of stations for debugfs.
The stations hold the ath_node, which holds the tid
and other xmit logic structures. In order to debug
stuck xmit logic, we need a way to print out the tid
state for the stations.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Mon, 10 Jan 2011 07:11:47 +0000 (23:11 -0800)]
ath9k: Ensure xmit makes progress.
If the txq->axq_q is empty, the code was breaking out
of the tx_processq logic without checking to see if it should
transmit other queued AMPDU frames (txq->axq_acq).
This patches ensures ath_txq_schedule is called.
This needs review.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 5 Jan 2011 00:22:03 +0000 (16:22 -0800)]
iwlwifi: fix 4965 notification wait setup
The notification wait support code is shared
between 4965 and other AGN devices, so 4965
also has to initialize the data structures
for it, otherwise it crashes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 5 Jan 2011 00:22:02 +0000 (16:22 -0800)]
iwlagn: return error if PAN disable timeout
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 5 Jan 2011 00:22:01 +0000 (16:22 -0800)]
iwlagn: properly wait for PAN disable
Previously I hacked this with an msleep(300)
which was fine since we never had longer PAN
time slots, but now that we will have them I
need to fix that. Use the new notification
wait support to properly wait for the WIPAN
deactivation complete signal from the ucode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 5 Jan 2011 00:22:00 +0000 (16:22 -0800)]
iwlagn: add support for waiting for notifications
In order to implement waiting for notifications,
add a structure that captures the information,
and a list of such structures that will be
traversed when a command is received from the
ucode.
Use sparse checking to make sure calls to the
prepare/wait/cancel functions are always nested
correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 5 Jan 2011 00:21:59 +0000 (16:21 -0800)]
iwlagn: make iwl_rx_handle static
It's not used or likely to be needed from other
files, so it can be static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 18 Jan 2011 14:48:48 +0000 (15:48 +0100)]
mac80211: drop non-auth 3-addr data frames when running as a 4-addr station
When running as a 4-addr station against an AP that has the 4-addr VLAN
interface and the main 3-addr AP interface bridged together, sometimes
frames originating from the station were looping back from the 3-addr AP
interface, causing the bridge code to emit warnings about receiving frames
with its own source address.
I'm not sure why this is happening yet, but I think it's a good idea to
drop all frames (except 802.1x/EAP frames) that do not match the configured
addressing mode, including 4-address frames sent to a 3-address station.
User test reports indicate that the problem goes away with this patch.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 18 Jan 2011 12:52:23 +0000 (13:52 +0100)]
mac80211: allow advertising correct maximum aggregate size
Currently, mac80211 always advertises that it may send
up to 64 subframes in an aggregate. This is fine, since
it's the max, but might as well be set to zero instead
since it doesn't have any information.
However, drivers might have that information, so allow
them to set a variable giving it, which will then be
used. The default of zero will be fine since to the
peer that means we don't know and it will just use its
own limit for the buffer size.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation code currently doesn't implement the
buffer size negotiation. It will always request a max
buffer size (which is fine, if a little pointless, as
the mac80211 code doesn't know and might just use 0
instead), but if the peer requests a smaller size it
isn't possible to honour this request.
In order to fix this, look at the buffer size in the
addBA response frame, keep track of it and pass it to
the driver in the ampdu_action callback when called
with the IEEE80211_AMPDU_TX_OPERATIONAL action. That
way the driver can limit the number of subframes in
aggregates appropriately.
Note that this doesn't fix any drivers apart from the
addition of the new argument -- they all need to be
updated separately to use this variable!
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 18 Jan 2011 12:45:32 +0000 (13:45 +0100)]
mac80211: don't return beacons when mesh is disabled
When mesh is disabled, mac80211 was returning
beacons with an empty mesh ID. That isn't
desirable, even if drivers shouldn't be trying
to get beacons to start with.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Sat, 15 Jan 2011 19:13:48 +0000 (19:13 +0000)]
ath9k: Fix up hardware mode and beacons with multiple vifs.
When using a mixture of AP and Station interfaces,
the hardware mode was using the type of the
last VIF registered. Instead, we should keep track
of the number of different types of vifs and set the
mode accordingly.
In addtion, use the vif type instead of hardware opmode
when dealing with beacons.
Attempt to move some of the common setup code into smaller
methods so we can re-use it when changing vif mode as
well as adding/deleting vifs.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 15 Jan 2011 13:30:15 +0000 (14:30 +0100)]
ath9k: fix excessive BAR sending when a frame exceeds its retry limit
Because the sendbar variable was not reset to zero, the stack would send
Block ACK requests for all subframes following the one that failed, which
could mess up the receiver side block ack window.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 15 Jan 2011 13:30:14 +0000 (14:30 +0100)]
ath9k: try more than one tid when scheduling a new aggregate
Sometimes the first TID in the first AC's list is not available for forming
a new aggregate (the BAW might not allow it), however other TIDs may have
data available for sending.
Prevent a slowdown of other TIDs by going through multiple entries until
we've either hit the last one or enough AMPDUs are pending in the hardware
queue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_htc: keep calibrated noise floor value for oper channel
The ath9k_hw assumes that caldata is valid only for
oper channel. But with ath9k_htc case, the caldata is
passed for all channels on hw_reset though we are not doing
calibration on that channel. So the oper channel's nf history
got cleared to default due to mismatch in channel flags.
This patch also saves some space.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: preserve caldata history buffer across scanning
caldata's channel info is never filled with operating channel
info which is causing the operating channel's noise floor
history buffer is reset to default nf during channel change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 13 Jan 2011 23:06:27 +0000 (00:06 +0100)]
ath9k_hw: partially revert "fix dma descriptor rx error bit parsing"
The rx error bit parsing was changed to consider PHY errors and various
decryption errors separately. While correct according to the documentation,
this is causing spurious decryption error reports in some situations.
Fix this by restoring the original order of the checks in those places,
where the errors are meant to be mutually exclusive.
If a CRC error is reported, then MIC failure and decryption errors
are irrelevant, and a PHY error is unlikely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Wed, 12 Jan 2011 13:26:30 +0000 (15:26 +0200)]
mac80211: add hw configuration for max ampdu buffer size
Some devices don't support the maximum AMDPU buffer size of 64, so we
need to add an option to configure this in the hardware configuration.
This value will be used in the ADDBA response instead of the value
suggested in the request, if the latter is greater than the max
supported.
Signed-off-by: Luciano Coelho <coelho@ti.com> Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 11 Jan 2011 00:05:50 +0000 (17:05 -0700)]
ath9k: reduce the likelihood of baseband hang check false positives
Since baseband hangs are rare, but the hang check function has a high
false positive rate in some situations, we need to add more reliable
indicators.
In AP mode we can use blocked beacon transmissions as an indicator,
they should be rare enough.
In station mode, we can skip the hang check entirely, since a true
hang will trigger beacon loss detection, and mac80211 will rescan,
which leads to a hw reset that will bring the hardware back to life.
To make this more reliable, we need to skip fast channel changes
if the hardware appears to be stuck.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 11 Jan 2011 00:05:48 +0000 (17:05 -0700)]
ath9k: fix initial sequence number after starting an ampdu session
txtid->seq_start may not always be up to date, when there is HT non-AMPDU
traffic just before starting an AMPDU session. Relying on txtid->seq_next
is better, since it is also used to generate the sequence numbers for
all QoS data frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 11 Jan 2011 00:05:47 +0000 (17:05 -0700)]
ath9k: fix bogus sequence number increases on aggregation tid flush
When a tid pointer is passed to ath_tx_send_normal(), it increases the
starting sequence number for the next AMPDU action frame, which should
only be done if the sequence number assignment is fresh. In this case
it is clearly not.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
RA-Jay Hung [Mon, 10 Jan 2011 10:28:10 +0000 (11:28 +0100)]
rt2x00: Fix and fine-tune rf registers for RT3070/RT3071/RT3090
Basically fix and fine-tune RT3070/RT3071/RT3090 chip RF initial value
when call rt2800_init_rfcsr
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
RA-Jay Hung [Mon, 10 Jan 2011 10:27:43 +0000 (11:27 +0100)]
rt2x00: Fix radio off hang issue for PCIE interface
PCI/PCIE radio off behavior is different from SOC/USB.
They mainly use MCU command to disable DMA, TX/RX and enter power saving mode.
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joel A Fernandes [Mon, 10 Jan 2011 06:44:23 +0000 (00:44 -0600)]
mac80211: Rewrote code for checking if destinations are proxied.
Rewrote code for checking if the destination is proxied by a mesh portal, to facilitate better
understanding of the functionality.
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Acked-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
For USB devices, reading the EEPROM data can be offloaded
to the target. Use multiple register reads to take advantage
of this feature to reduce initialization time.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
set_key callback is defined for mac80211 to install keys for HW crypto in AP
mode. Driver currently falls back to SW crypto in STA mode. Add support to
configure the keys appropriately in the hardware after the set_key routine is
called.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com> Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: Set mac80211 rx status flags appropriately when hw crypto is enabled
When hw crypto is enabled, set rx status flags appropriately depending on
whether hw crypto is enabled for a particular bss.
Also report MIC errors to mac80211, so that counter measures can be
initiated
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: yogesh powar <yogeshp@marvell.com> Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: Modify add_dma_header to include pad parameters
Add capability to add_dma_header to support padding at tail of the data
packet to be transmitted when crypto is enabled. Padding is required for
adding crypto information in data packets for supporting 802.11 security
modes.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com> Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds [Tue, 18 Jan 2011 22:29:37 +0000 (14:29 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Validate cpu early in perf_event_alloc()
perf: Find_get_context: fix the per-cpu-counter check
perf: Fix contexted inheritance
Linus Torvalds [Tue, 18 Jan 2011 22:29:21 +0000 (14:29 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Clear irqstack thread_info
x86: Make relocatable kernel work with new binutils
Linus Torvalds [Tue, 18 Jan 2011 22:28:48 +0000 (14:28 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Malta: enable Cirrus FB console
MIPS: add CONFIG_VIRTUALIZATION for virtio support
MIPS: Implement __read_mostly
MIPS: ath79: add common WMAC device for AR913X based boards
MIPS: ath79: Add initial support for the Atheros AP81 reference board
MIPS: ath79: add common SPI controller device
SPI: Add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs
MIPS: ath79: add common GPIO buttons device
MIPS: ath79: add common watchdog device
MIPS: ath79: add common GPIO LEDs device
MIPS: ath79: add initial support for the Atheros PB44 reference board
MIPS: ath79: utilize the MIPS multi-machine support
MIPS: ath79: add GPIOLIB support
MIPS: Add initial support for the Atheros AR71XX/AR724X/AR931X SoCs
MIPS: jump label: Add MIPS support.
MIPS: Use WARN() in uasm for better diagnostics.
MIPS: Optimize TLB handlers for Octeon CPUs
MIPS: Add LDX and LWX instructions to uasm.
MIPS: Use BBIT instructions in TLB handlers
MIPS: Declare uasm bbit0 and bbit1 functions.
...
Oleg Nesterov [Tue, 18 Jan 2011 16:10:08 +0000 (17:10 +0100)]
perf: Find_get_context: fix the per-cpu-counter check
If task == NULL, find_get_context() should always check that cpu
is correct.
Afaics, the bug was introduced by 38a81da2 "perf events: Clean
up pid passing", but even before that commit "&& cpu != -1" was
not exactly right, -ESRCH from find_task_by_vpid() is not
accurate.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Prasad <prasad@linux.vnet.ibm.com> Cc: Roland McGrath <roland@redhat.com> Cc: gregkh@suse.de Cc: stable@kernel.org
LKML-Reference: <20110118161008.GB693@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Aurelien Jarno [Tue, 18 Jan 2011 11:20:45 +0000 (12:20 +0100)]
MIPS: Malta: enable Cirrus FB console
While most users of a physical Malta board are using the serial port
as the console, a lot of QEMU users would prefer to interact with a
graphical console. Enable the Cirrus FB support in the Malta default
configuration to make that possible. Note that the default console will
still be the serial port, users have to pass "console=tty0" to the
kernel to use the Cirrus FB.
David Daney [Thu, 14 Oct 2010 19:36:49 +0000 (12:36 -0700)]
MIPS: Implement __read_mostly
Just do what everyone else is doing by placing __read_mostly things in
the .data.read_mostly section.
mips_io_port_base can not be read-only (const) and writable
(__read_mostly) at the same time. One of them has to go, so I chose
to eliminate the __read_mostly. It will still get stuck in a portion
of memory that is not adjacent to things that are written, and thus
not be on a dirty cache line, for whatever that is worth.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1702/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Gabor Juhos [Tue, 4 Jan 2011 20:28:29 +0000 (21:28 +0100)]
MIPS: ath79: add common WMAC device for AR913X based boards
Add common platform_device and helper code to make the registration
of the built-in wireless MAC easier on the Atheros AR9130/AR9132
based boards. Also register the WMAC device on the AR81 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: linux-mips@linux-mips.org Cc: Imre Kaloz <kaloz@openwrt.org>, Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Cc: Cliff Holden <Cliff.Holden@Atheros.com> Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1962/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Gabor Juhos [Tue, 4 Jan 2011 20:28:23 +0000 (21:28 +0100)]
MIPS: ath79: add common SPI controller device
Several boards are using the built-in SPI controller of the
AR71XX/AR724X/AR913X SoCs. This patch adds common platform_device
and helper code to register it. Additionally, the patch registers
the SPI bus on the PB44 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: linux-mips@linux-mips.org Cc: Imre Kaloz <kaloz@openwrt.org> Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Cc: Cliff Holden <Cliff.Holden@Atheros.com> Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1956/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current patch contains minimal support only, but the resulting
kernel can boot into user-space with using of an initramfs image on
various boards which are using these SoCs. Support for more built-in
devices and individual boards will be implemented in further patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Cc: linux-mips@linux-mips.org Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Cc: Cliff Holden <Cliff.Holden@Atheros.com> Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1947/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 28 Dec 2010 21:26:23 +0000 (13:26 -0800)]
MIPS: jump label: Add MIPS support.
In order not to be left behind, we add jump label support for MIPS.
Tested on 64-bit big endian (Octeon), and 32-bit little endian
(malta/qemu).
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Jason Baron <jbaron@redhat.com>
Patchwork: https://patchwork.linux-mips.org/patch/1923/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 28 Dec 2010 02:18:29 +0000 (18:18 -0800)]
MIPS: Use WARN() in uasm for better diagnostics.
On the off chance that uasm ever warns about overflow, there is no way
to know what the offending instruction is.
Change the printks to WARNs, so we can get a nice stack trace. It has
the added benefit of being much more noticeable than the short single
line warning message, so is less likely to be ignored.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1905/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Mon, 20 Dec 2010 23:54:50 +0000 (15:54 -0800)]
MIPS: Use BBIT instructions in TLB handlers
If the CPU supports BBIT0 and BBIT1, use them in TLB handlers as they
are more efficient than an AND followed by an branch and then
restoring the clobbered register.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1873/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Gabor Juhos [Tue, 23 Nov 2010 15:06:25 +0000 (16:06 +0100)]
MIPS: Add generic support for multiple machines within a single kernel
This patch adds a generic solution to support multiple machines based on
a given SoC within a single kernel image. It is implemented already for
several other architectures but MIPS has no generic support for that yet.
[Ralf: This competes with DT but DT is a much more complex solution and this
code has been used by OpenWRT for a long time so for now DT is a bad reason
to stop the merge but longer term this should be migrated to DT.]
Linus Torvalds [Tue, 18 Jan 2011 16:05:50 +0000 (08:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix initialization for HP 2011 notebooks
ALSA: hda - Add support for VMware controller
ALSA: hda - consitify string arrays
ALSA: hda - Add add multi-streaming playback for AD1988
ASoC: EP93xx: fixed LRCLK rate and DMA oper. in I2S code
ASoC: WM8990: msleep() takes milliseconds not jiffies
ALSA : au88x0 - Limit number of channels to fix Oops via OSS emu
ALSA: constify functions in ac97
ASoC: WL1273 FM radio: Fix breakage with MFD API changes
ALSA: hda - More coverage for odd-number channels elimination for HDMI
ALSA: hda - Store PCM parameters properly in HDMI open callback
ALSA: hda - Rearrange fixup struct in patch_realtek.c
ALSA: oxygen: Xonar DG: fix CS4245 register writes
ALSA: hda - Suppress the odd number of channels for HDMI
ALSA: hda - Add fixup-call in init callback
ALSA: hda - Reorganize fixup structure for Realtek
ALSA: hda - Apply Sony VAIO hweq fixup only once
ALSA: hda - Apply mario fixup only once
ALSA: hda - Remove unused fixup entry for ALC262
Linus Torvalds [Tue, 18 Jan 2011 16:05:20 +0000 (08:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (25 commits)
m68knommu: fix broken setting of irq_chip and handler
m68knommu: switch to using -mcpu= flags for ColdFire targets
m68knommu: arch/m68knommu/Kconfig whitespace cleanup
m68knommu: create optimal separate instruction and data cache for ColdFire
m68knommu: support ColdFire caches that do copyback and write-through
m68knommu: support version 2 ColdFire split cache
m68knommu: make cache push code ColdFire generic
m68knommu: clean up ColdFire cache control code
m68knommu: move inclusion of ColdFire v4 cache registers
m68knommu: merge bit definitions for version 3 ColdFire cache controller
m68knommu: create bit definitions for the version 2 ColdFire cache controller
m68knommu: remove empty __iounmap() it is no used
m68knommu: remove kernel_map() code, it is not used
m68knommu: remove do_page_fault(), it is not used
m68knommu: use user stack pointer hardware on some ColdFire cores
m68knommu: remove command line printing DEBUG
m68knommu: remove fasthandler interrupt code
m68knommu: move UART addressing to part specific includes
m68knommu: fix clock rate value reported for ColdFire 54xx parts
m68knommu: move ColdFire CPU names into their headers
...
Linus Torvalds [Tue, 18 Jan 2011 16:04:30 +0000 (08:04 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix tracepoint id to string perf.data header table
perf tools: Fix handling of wildcards in tracepoint event selectors
powerpc: perf: Fix frequency calculation for overflowing counters
Linus Torvalds [Tue, 18 Jan 2011 15:58:36 +0000 (07:58 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
autofs4: clean ->d_release() and autofs4_free_ino() up
autofs4: split autofs4_init_ino()
autofs4: mkdir and symlink always get a dentry that had passed lookup
autofs4: autofs4_get_inode() doesn't need autofs_info * argument anymore
autofs4: kill ->size in autofs_info
autofs4: pass mode to autofs4_get_inode() explicitly
autofs4: autofs4_mkroot() is not different from autofs4_init_ino()
autofs4: keep symlink body in inode->i_private
autofs4 - fix debug print in autofs4_lookup()
vfs - fix dentry ref count in do_lookup()
autofs4 - fix get_next_positive_dentry()
projects / karo-tx-linux.git / log