Mark Rustad [Thu, 5 Nov 2015 19:02:14 +0000 (11:02 -0800)]
ixgbe: Always turn PHY power on when requested
Instead of inhibiting PHY power control when manageability is
present, only inhibit turning PHY power off when manageability
is present. Consequently, PHY power will always be turned on when
requested. Without this patch, some systems with X540 or X550
devices in some conditions will never get link.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Wed, 18 Nov 2015 17:21:28 +0000 (09:21 -0800)]
ixgbe: Handle extended IPv6 headers in Tx path
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for recognizing problems with the first version
of this patch and recognizing how to coalesce error conditions
into a single location.
Reported-by: Tom Herbert <tom@herbertland.com> Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Fri, 30 Oct 2015 22:29:34 +0000 (15:29 -0700)]
ixgbe: Save VF info and take references
Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Tue, 27 Oct 2015 20:23:23 +0000 (13:23 -0700)]
ixgbe: Wait for master disable to be set
According to the datasheets, the driver should wait for the master
disable bit to read as being set before checking the status
register for master disable.
Reported-by: Dan Streetman <dan.streetman@canonical.com> Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Tue, 27 Oct 2015 20:23:14 +0000 (13:23 -0700)]
ixgbe: Correct spec violations by waiting after reset
The ixgbe driver was violating the specification in the datasheet
by not waiting 1ms before checking for the reset bit clearing. This
is called out for devices supported by ixgbe, so implement the
required delay.
Reported-by: Dan Streetman <dan.streetman@canonical.com> Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Tue, 27 Oct 2015 16:58:07 +0000 (09:58 -0700)]
ixgbe: Update PTP to support X550EM_x devices
The X550EM_x devices handle clocking differently, so update the
PTP implementation to accommodate them. This involves significant
changes to ixgbe's PTP code to accommodate the new range of
behaviors including things like non-power-of-2 clock wrapping.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 22 Oct 2015 23:26:42 +0000 (16:26 -0700)]
ixgbe: Allow FDB entries access to more RAR filters
This change makes it so that we allow the PF to make use of all free RAR
entries for FDB use if needed.
Previously the code limited us to 16 unicast entries, however this was
shared between MACVLAN which wasn't limited and the FDB code which was. So
instead of treating the FDB code as a second class citizen I have updated
it so that it has access to just as many entries as the MACVLAN filters.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 22 Oct 2015 23:26:36 +0000 (16:26 -0700)]
ixgbe: Use __dev_uc_sync and __dev_uc_unsync for unicast addresses
This change replaces the ixgbe_write_uc_addr_list call in ixgbe_set_rx_mode
with a call to __dev_uc_sync instead. This works much better with the MAC
addr list code that was already in place and solves an issue in which you
couldn't remove an FDB address without having to reset the port.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 22 Oct 2015 23:26:30 +0000 (16:26 -0700)]
ixgbe: Refactor MAC address configuration code
In the process of tracking down a memory leak when adding/removing FDB
entries I had to go through the MAC address configuration code for ixgbe.
In the process of doing so I found a number of issues that impacted
readability and performance. This change updates the code in general to
clean it up so it becomes clear what each step is doing. From what I can
tell there a couple of bugs cleaned up in this code.
First is the fact that the MAC addresses were being double counted for the
PF. As a result once entries up to 63 had been used you could no longer
add additional filters.
A simple test case for this:
for i in `seq 0 96`
do
ip link add link ens8 name mv$i type macvlan
ip link set dev mv$i up
done
When things are working correctly RAL/H registers 1 - 97 will be consumed.
In the failing case it will stop at 63 and prevent any further filters from
being added.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Thu, 22 Oct 2015 00:21:20 +0000 (17:21 -0700)]
ixgbevf: Minor cleanups
Make some minor cleanups, such as simplifying return paths, deleting
unneeded initializations, return values more directly and so forth.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Thu, 22 Oct 2015 00:21:15 +0000 (17:21 -0700)]
ixgbevf: Use a private workqueue to avoid certain possible hangs
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Thu, 22 Oct 2015 00:21:10 +0000 (17:21 -0700)]
ixgbe: Use private workqueue to avoid certain possible hangs
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Mon, 19 Oct 2015 16:22:14 +0000 (09:22 -0700)]
ixgbe: Add support for newer thermal alarm
The newer copper PHY implementation used with newer X550EM_x
devices uses a different thermal alarm type than the earlier
one. Make changes to support both types.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Fri, 16 Oct 2015 20:27:49 +0000 (13:27 -0700)]
ixgbe: Prevent KR PHY reset in ixgbe_init_phy_ops_x550em
This patch removes KR PHY reset from ixgbe_init_phy_ops_x550em,
since this function is meant to initialize function pointers for
the detected PHY type. Internal PHY reset was moved to
ixgbe_setup_internal_phy_t_x550em which will now detect which
mode the internal PHY operates in and set it up as required.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Darin Miller <darin.j.miller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jarod Wilson [Mon, 30 Nov 2015 22:12:21 +0000 (17:12 -0500)]
sfc: use ALIGN macro for aligning frame sizes
Don't open-code it.
CC: Solarflare linux maintainers <linux-net-drivers@solarflare.com> CC: Shradha Shah <sshah@solarflare.com> CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Acked-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 30 Nov 2015 16:57:28 +0000 (08:57 -0800)]
tcp: suppress too verbose messages in tcp_send_ack()
If tcp_send_ack() can not allocate skb, we properly handle this
and setup a timer to try later.
Use __GFP_NOWARN to avoid polluting syslog in the case host is
under memory pressure, so that pertinent messages are not lost under
a flood of useless information.
sk_gfp_atomic() can use its gfp_mask argument (all callers currently
were using GFP_ATOMIC before this patch)
We rename sk_gfp_atomic() to sk_gfp_mask() to clearly express this
function now takes into account its second argument (gfp_mask)
Note that when tcp_transmit_skb() is called with clone_it set to false,
we do not attempt memory allocations, so can pass a 0 gfp_mask, which
most compilers can emit faster than a non zero or constant value.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 3 Dec 2015 04:43:48 +0000 (23:43 -0500)]
Merge branch 'hv_netvsc-less-headroom'
Merge branch 'hv_netvsc-less-headroom'
K. Y. Srinivasan says:
====================
hv_netvsc: Eliminate the additional head room
In an attempt to avoid having to allocate memory on the send path, the netvsc
driver was requesting additional head room so that both rndis header and the
netvsc packet (the state that had to persist) could be placed in the skb.
Since the amount of head room requested was exceeding the default head room
as set in LL_MAX_HEADER, we were forcing a reallocation of skb.
With this patch-set, I have reduced the size of the netvsc packet to less
than 20 bytes and with this reduction we don't need to ask for any additional
headroom. We place the rndis header in the skb head room and we place the
netvsc packet in control buffer area in the skb.
V2: - Addressed review comments:
- Eliminated more fields from netvsc packet structure.
V3: - Fixed a typo in patch: hv_netvsc: Don't ask for additional head room in the skb.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:13 +0000 (16:43 -0800)]
hv_netvsc: Eliminate page_buf from struct hv_netvsc_packet
Eliminate page_buf from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Packet scheduler guarantees there won't be multiple senders for the same
queue and as we use q_idx for multi_send_data the spinlock is redundant.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hv_netvsc: move subchannel existence check to netvsc_select_queue()
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:10 +0000 (16:43 -0800)]
hv_netvsc: Don't ask for additional head room in the skb
The rndis header is 116 bytes big and can be placed in the default
head room that will be available in the skb. Since the netvsc packet
is less than 48 bytes, we can use the skb control buffer
for the netvsc packet. With these changes we don't need to
ask for additional head room.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:09 +0000 (16:43 -0800)]
hv_netvsc: Eliminate send_completion_ctx from struct hv_netvsc_packet
Eliminate send_completion_ctx from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:08 +0000 (16:43 -0800)]
hv_netvsc: Eliminate send_completion from struct hv_netvsc_packet
Eliminate send_completion from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:07 +0000 (16:43 -0800)]
hv_netvsc: Eliminatte the data field from struct hv_netvsc_packet
Eliminatte the data field from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:06 +0000 (16:43 -0800)]
hv_netvsc: Eliminate rndis_msg pointer from hv_netvsc_packet structure
Eliminate rndis_msg pointer from hv_netvsc_packet structure.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:05 +0000 (16:43 -0800)]
hv_netvsc: Eliminate the channel field in hv_netvsc_packet structure
Eliminate the channel field in hv_netvsc_packet structure.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:04 +0000 (16:43 -0800)]
hv_netvsc: Rearrange the hv_negtvsc_packet to be space efficient
Rearrange the elements of struct hv_negtvsc_packet for optimal layout -
eliminate unnecessary padding.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Wed, 2 Dec 2015 00:43:03 +0000 (16:43 -0800)]
hv_netvsc: Resize some of the variables in hv_netvsc_packet
As part of reducing the size of the hv_netvsc_packet, resize some of the
variables based on their usage.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 2 Dec 2015 20:32:50 +0000 (15:32 -0500)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-12-01
This series contains updates to i40e and i40evf only.
Helin adds new fields to i40e_vsi to store user configured RSS config data
and the code to use it. Also renamed RSS items to clarify functionality
and scope to users. Fixed a confusing kernel message of enabling RSS size
by reporting it together with the hardware maximum RSS size.
Anjali fixes the issue of forcing writeback too often causing us to not
benefit from NAPI.
Jesse adds a prefetch for data early in the transmit path to help immensely
for pktgen and forwarding workloads. Fixed the i40e driver that was
possibly sleeping inside critical section of code.
Carolyn fixes an issue where adminq init failures always provided a message
that NVM was newer than expected, when this is not always the case for
init_adminq failures. Fixed by adding a check for that specific error
condition and a different helpful message otherwise.
Mitch fixes error message by telling the user which VF is being naughty,
rather than making them guess. Updated the queue_vector array from a
statically-sized member of the adapter structure, to a dynamically-allocated
and -sized array. This reduces the size of the adapter structure and allows
us to support any number of queue vectors in the future without changing the
code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With the final edition of the patches to remove sleeps from
the driver's entry points, the grab_rtnl argument is no
longer needed, so partially revert the commit that added it.
Change-ID: Ib9778476242586cc9e58b670f5f48d415cb59003 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was being called by VLAN, bonding, teaming operations
that expected to be able to hold locks like rcu_read_lock().
This causes the driver to be held to the requirement to not sleep,
and was found by the kernel debug options for checking sleep
inside critical section, and the locking validator.
Change-ID: Ibc68c835f5ffa8ffe0638ffe910a66fc5649a7f7 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 26 Oct 2015 23:44:40 +0000 (19:44 -0400)]
i40evf: allocate ring structs dynamically
Instead of awkwardly keeping a fixed array of pointers in the adapter
struct and then allocating ring structs individually, just keep a single
pointer and allocate a single blob for the arrays. This simplifies code,
shrinks the adapter structure, and future-proofs the driver by not
limiting the number of rings we can handle.
Change-ID: I31334ff911a6474954232cfe4bc98ccca3c769ff Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 26 Oct 2015 23:44:39 +0000 (19:44 -0400)]
i40evf: allocate queue vectors dynamically
Change the queue_vector array from a statically-sized member of the
adapter structure to a dynamically-allocated and -sized array.
This reduces the size of the adapter structure, and allows us to support
any number of queue vectors in the future without changing the code.
Change-ID: I08dc622cb2f2ad01e832e51c1ad9b86524730693 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 26 Oct 2015 23:44:38 +0000 (19:44 -0400)]
i40evf: quoth the VF driver, Nevermore
If, upon a midnight dreary, the PF returns ERR_PARAM when the VF is
requesting resources, that's fatal. Either the firmware or NVM is badly,
badly misconfigured, or this VF has been disabled due to a previous VF
driver sending a bunch of bogus messages.
Either way, there is no recovery from this. Don't ponder weak and weary,
just quit.
Change-ID: I09d9f16cc4ee7fec3b57646a289d33838c1c5bf5 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 26 Oct 2015 23:44:37 +0000 (19:44 -0400)]
i40e: make error message more useful
If we get an invalid message from a VF, we should tell the user which VF
is being naughty, rather than making them guess.
Change-ID: I9252cef7baea3d8584043ed6ff12619a94e2f99c Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Mon, 26 Oct 2015 23:44:35 +0000 (19:44 -0400)]
i40e: Update error messaging
This patch fixes an issue where adminq init failures always provided
a message that NVM was newer than expected. This is not always the
case for init_adminq failures. Without this patch, if adminq init
fails for any reason, newer NVM message would be given. This
problem is fixed by adding a check for that specific error
condition and a different hopefully helpful message otherwise.
Change-ID: Iaeaebee4e398989eae40bb70f943ab66a3a521a5 Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Helin Zhang [Mon, 26 Oct 2015 23:44:33 +0000 (19:44 -0400)]
i40evf: create a generic get RSS function
There are two ways to get RSS, this patch implements two functions
with the same input parameters, and creates a more generic function
for getting RSS configuration.
Change-ID: I12d3b712c21455d47dd0a5aae58fc9b7c680db59 Signed-off-by: Helin Zhang <helin.zhang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Helin Zhang [Tue, 27 Oct 2015 20:15:06 +0000 (16:15 -0400)]
i40evf: create a generic config RSS function
There are two ways to configure RSS, this patch adjusts those two
functions with the same input parameters, and creates a more
generic function for configuring RSS.
Change-ID: Iace73bdeba4831909979bef221011060ab327f71 Signed-off-by: Helin Zhang <helin.zhang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesse Brandeburg [Mon, 26 Oct 2015 23:44:30 +0000 (19:44 -0400)]
i40e/i40evf: prefetch skb data on transmit
Issue a prefetch for data early in the transmit path.
This should not be generally needed for Tx traffic, but
it helps immensely for pktgen workloads and should help
for forwarding workloads as well.
Change-ID: Iefee870c20599e0c4240e1d8637e4f16b625f83a Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e/i40evf: Fix RS bit update in Tx path and disable force WB workaround
This patch fixes the issue of forcing WB too often causing us to not
benefit from NAPI.
Without this patch we were forcing WB/arming interrupt too often taking
away the benefits of NAPI and causing a performance impact.
With this patch we disable force WB in the clean routine for X710
and XL710 adapters. X722 adapters do not enable interrupt to force
a WB and benefit from WB_ON_ITR and hence force WB is left enabled
for those adapters.
For XL710 and X710 adapters if we have less than 4 packets pending
a software Interrupt triggered from service task will force a WB.
This patch also changes the conditions for setting RS bit as described
in code comments. This optimizes when the HW does a tail bump amd when
it does a WB. It also optimizes when we do a wmb.
Change-ID: Id831e1ae7d3e2ec3f52cd0917b41ce1d22d75d9d Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Helin Zhang [Mon, 26 Oct 2015 23:44:28 +0000 (19:44 -0400)]
i40e: rename rss_size to alloc_rss_size in i40e_pf
This patch renames rss_size to alloc_rss_size in i40e_pf, which is
clearer and avoids confusion. It also adds comments to the other
related structure members to help clarify usage.
Change-ID: Ia90090609d006ab589cb639975bb8a0af795d16f Signed-off-by: Helin Zhang <helin.zhang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Arnd Bergmann [Mon, 30 Nov 2015 10:34:09 +0000 (11:34 +0100)]
isdn: remove spellcaster driver
The 'sc' ISDN driver relies on using readl() to access ISA I/O memory.
This has been deprecated and produced warnings since linux-2.3.23,
disabled by default since 2.4.10 and finally removed in 2.6.5.
I found this because the compiling the driver for ARM produces
a warning:
In file included from ../drivers/isdn/sc/includes.h:8:0,
from ../drivers/isdn/sc/init.c:13:
../arch/arm/include/asm/io.h:115:21: note: expected 'const volatile void *' but argument is of type 'long unsigned int'
It is pretty clear that this driver has not been used for a long time
and there is no point fixing it now, so let's remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
For GMAC newer than 3.40a there is a new register (Reg_9) that provides the
status of all modules of the transmit and receive paths and FIFO status.
These can be exposed via ethtool.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 1 Dec 2015 21:02:41 +0000 (16:02 -0500)]
Merge branch 'qed-ethtool-ops'
Yuval Mintz says:
====================
qede/qed: Implement various ethtool operations
This series adds several new ethtool operations to qede:
- {get, set}_channels
- {get, set}_ringparam
- set_phys_id
- nway_reset
- {get, set}_pauseparam
As well as extending the qed APIs to support these commands.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Physical LEDs are being controlled by the management FW.
This adds the qed functionality required to request management FW to
change the LED configuration, as well as the necessary APIs for this
functionality to later be used by the protocol drivers.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 1 Dec 2015 20:46:40 +0000 (15:46 -0500)]
Merge branch 'sfc-8000'
Bert Kenward says:
====================
Basic support for Solarflare 8000 series NICs
The upcoming Solarflare 8000 series 10G/40G network card supports a
similar interface to the current 7000 series cards. This patch series
provides basic support for these cards, making no use of any new
functionality.
v2: fix indenting in ef10.c in patch 1/2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Mon, 30 Nov 2015 09:05:35 +0000 (09:05 +0000)]
sfc: make TSO version a per-queue parameter
The Solarflare 8000 series NIC will use a new TSO scheme. The current
driver refuses to load if the current TSO scheme is not found. Remove
that check and instead make the TSO version a per-queue parameter.
Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: add support for netdev notifier error injection
This module allows to insert errors in some of netdevice's notifier
events. All network drivers use these notifiers to signal various events
and to check if they are allowed, e.g. PRECHANGEMTU and CHANGEMTU
afterwards. Until recently I had to run failure tests by injecting
a custom module, but now this infrastructure makes it trivial to test
these failure paths. Some of the recent bugs I fixed were found using
this module.
Here's an example:
$ cd /sys/kernel/debug/notifier-error-inject/netdev
$ echo -22 > actions/NETDEV_CHANGEMTU/error
$ ip link set eth0 mtu 1024
RTNETLINK answers: Invalid argument
CC: Akinobu Mita <akinobu.mita@gmail.com> CC: "David S. Miller" <davem@davemloft.net> CC: netdev <netdev@vger.kernel.org> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Fri, 27 Nov 2015 10:39:55 +0000 (11:39 +0100)]
hv_netvsc: rework link status change handling
There are several issues in hv_netvsc driver with regards to link status
change handling:
- RNDIS_STATUS_NETWORK_CHANGE results in calling userspace helper doing
'/etc/init.d/network restart' and this is inappropriate and broken for
many reasons.
- link_watch infrastructure only sends one notification per second and
in case of e.g. paired disconnect/connect events we get only one
notification with last status. This makes it impossible to handle such
situations in userspace.
Redo link status changes handling in the following way:
- Create a list of reconfig events in network device context.
- On a reconfig event add it to the list of events and schedule
netvsc_link_change().
- In netvsc_link_change() ensure 2-second delay between link status
changes.
- Handle RNDIS_STATUS_NETWORK_CHANGE as a paired disconnect/connect event.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rainer Weikusat [Thu, 26 Nov 2015 19:23:15 +0000 (19:23 +0000)]
unix: use wq_has_sleeper in unix_dgram_recvmsg
The current unix_dgram_recvmsg does a wake up for every received
datagram. This seems wasteful as only SOCK_DGRAM client sockets in an
n:1 association with a server socket will ever wait because of the
associated condition. The patch below changes the function such that the
wake up only happens if wq_has_sleeper indicates that someone actually
wants to be notified. Testing with SOCK_SEQPACKET and SOCK_DGRAM socket
seems to confirm that this is an improvment.
Signed-Off-By: Rainer Weikusat <rweikusat@mobileactivedefense.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Nov 2015 20:26:23 +0000 (15:26 -0500)]
Merge branch 'ipmr-nl'
Nikolay Aleksandrov says:
====================
net: ipmr: more cleanups and mfc netlink support
This set continues with the minor cleanups in the first 6 patches and
patch 7 adds the first new feature - MFC manipulation via netlink. It
registers NEWROUTE/DELROUTE for that purpose and uses the same semantics
as the already present netlink dump. The only new attribute that is used
is RTA_PREFSRC to denote an MFC_PROXY entry. Currently the table must
exist before adding an entry, and new tables can be created only via
setsockopt, but that will be changed in the future.
This set was tested with modified iproute2 which supports NEWROUTE/DELROUTE
for RTNL_FAMILY_IPMR.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipmr: add mfc newroute/delroute netlink support
This patch adds support to add and remove MFC entries. It uses the
same attributes like the already present dump support in order to be
consistent. There's one new entry - RTA_PREFSRC, it's used to denote an
MFC_PROXY entry (see MRT_ADD_MFC vs MRT_ADD_MFC_PROXY).
The already existing infrastructure is used to create and delete the
entries, the netlink message gets converted internally to a struct mfcctl
which is used with ipmr_mfc_add/delete.
The other used attributes are:
RTA_IIF - used for mfcc_parent (when adding it's required to be valid)
RTA_SRC - used for mfcc_origin
RTA_DST - used for mfcc_mcastgrp
RTA_TABLE - the MRT table id
RTA_MULTIPATH - the "oifs" ttl array
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Remove extra spaces and tabs, adjust function definitions, remove an
unnecessary ifdef (already used below, just move code) and drop extern
from the functions.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipmr: remove unused MFC_NOTIFY flag and make the flags enum
MFC_NOTIFY was introduced in kernel 2.1.68 but afaik it hasn't been used
and I couldn't find any users currently so just remove it. Only
MFC_STATIC is left, so move it into an enum, add a description and use
BIT().
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like many files are including mroute.h unnecessarily, so remove
the include. Most importantly remove it from ipv6.
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> CC: Steffen Klassert <steffen.klassert@secunet.com> CC: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Thu, 26 Nov 2015 05:55:39 +0000 (13:55 +0800)]
net: Generalise wq_has_sleeper helper
The memory barrier in the helper wq_has_sleeper is needed by just
about every user of waitqueue_active. This patch generalises it
by making it take a wait_queue_head_t directly. The existing
helper is renamed to skwq_has_sleeper.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Nov 2015 03:32:32 +0000 (22:32 -0500)]
Merge tag 'wireless-drivers-next-for-davem-2015-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Add vendor directories (for example intel, marvell and so on) to
drivers/net/wireless and change the menuconfig to follow the same
categorisation. This unifies the directory layout as we already had few drivers
already using vendor directories (especially ath and ti).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 25 Nov 2015 18:58:06 +0000 (13:58 -0500)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-11-25
This series contains updates to fm10k, i40e and i40evf.
Alex Duyck fixes up fm10k to use napi_schedule_irqoff() instead of
napi_schedule() since the function it is called from runs from hard interrupt
context or with interrupts already disabled in netpoll.
Shannon cleans up i40e and i40evf unused cd_tunneling parameter and any code
comments that refer to it. Then clean up a few instances of BUG_ON, based
on a Linux diatribe, especially when WARN_ON can be used.
Helin fixed a issue where using ethtool RXNFC command could let receive
flow hash could be set on disabled queues, so resolve by returning the
number of enabled queues before setting RXNFC.
Anjali fixes a MSS issue where the hardware/NVM sets a limit of no less than
256 bytes for MSS, yet the stack can send as low as 76 byte MSS. Fixed the
issue by lowering the hardware limit to 64 bytes to avoid MDDs from firing
and causing a reset when the MSS is lower than 256. Added a statistic to
track how many times we forced to do a write back on transmit if the
number of descriptors pending are less than a cache line.
Catherine fixes link status changes, where polling would only change link
status changes in one direction depending on what the last old data saved
off was. This was due to the watchdog only calling link_event and not
handle_link_event.
Mitch cleans up and enhances error messages related to VF MAC/VLAN filters.
v2: Dropped patch "i40e: Properly cast type for arithmetic" patch
based on feedback from the community
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Helin Zhang [Wed, 21 Oct 2015 23:56:23 +0000 (19:56 -0400)]
i40e: create a generic configure rss function
This patch renames the old pf-specific function in order to clarify
its scope. This patch also creates a more generic configure RSS
function with the old name.
This patch also creates a new more generic function to get RSS
configuration, using the appropriate method.
Change-ID: Ieddca2707b708ef19f1ebccdfd03a0a0cd63d3af Signed-off-by: Helin Zhang <helin.zhang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Helin Zhang [Wed, 21 Oct 2015 23:47:13 +0000 (19:47 -0400)]
i40e: return the number of enabled queues for ETHTOOL_GRXRINGS
This patch fixes a problem where using ethtool rxnfc command could
let RX flow hash be set on disabled queues. This patch fixes the
problem by returning the number of enabled queues before setting
rxnfc.
Change-ID: Idbac86b0b47ddacc8deee7cd257e41de01cbe5c0 Signed-off-by: Helin Zhang <helin.zhang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Wed, 21 Oct 2015 23:47:12 +0000 (19:47 -0400)]
i40evf: handle many MAC filters correctly
When a lot (many hundreds) of MAC or VLAN filters are added at one time,
we can overflow the Admin Queue buffer size with all the requests.
Unfortunately, the driver would then calculate the message size
incorrectly, causing it to be rejected by the PF. Furthermore, there was
no mechanism to trigger another request to allow for configuring the
rest of the filters that didn't fit into the first request.
To fix this, recalculate the correct buffer size when we detect the
overflow condition instead of just assuming the max buffer size. Also,
don't clear the request bit in adapter->aq_required when we have an
overflow, so that the rest of the filters can be processed later.
Change-ID: Idd7cbbc5af31315e0dcb1b10e6a02ad9817ce65c Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Wed, 21 Oct 2015 23:47:11 +0000 (19:47 -0400)]
i40e/i40evf: clean up error messages
Clean up and enhance error messages related to VF MAC/VLAN filters.
Indicate which VF is having issues, and if possible indicate the MAC
address or VLAN involved.
Also, when an error is returned from the PF driver, print useful
information about what went wrong, for the most likely cases.
Change-ID: Ib3d15eef9e3369a78fd142948671e5fa26d921b8 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e: Move the saving of old link info from handle_link_event to link_event
The watchdog only calls link_event not handle_link_event which means
that we need to save the old information in link_event.
Previously when polling we were comparing current data to the old data
saved the last time we actually received a link event. This means that
the polling would only fix link status changes in one direction
depending on what the last old data saved off was.
Change-ID: Ie590f30fdbcb133d0ddad4e07e3eb1aad58255b3 Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e/i40evf: Add a stat to track how many times we have to do a force WB
When in NAPI with interrupts disabled, the HW needs to be forced to do a
write back on TX if the number of descriptors pending are less than a
cache line.
This stat helps keep track of how many times we get into this situation.
Change-ID: I76c1bcc7ebccd6bffcc5aa33bfe05f2fa1c9a984 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
HW/NVM sets a limit of no less than 256 bytes for MSS. Stack can send as
low as 76 bytes MSS. This patch lowers the HW limit to 64 bytes to avoid
MDDs from firing and causing a reset when the MSS is lower than 256.
Change-ID: I36b500a6bb227d283c3e321a7718e0672b11fab0 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 21 Oct 2015 23:47:05 +0000 (19:47 -0400)]
i40e: remove BUG_ON from FCoE setup
There's no need to kill the kernel thread here. If this condition was
true, the probe() would have died long before we got here. In any case,
we'll get the same result when this code tries to use the VSI pointer
being checked.
Prompted by a recent Linus diatribe.
Change-ID: I62f531cac34d4fc28ff9657d5b2d9523ae5e33a4 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 21 Oct 2015 23:47:04 +0000 (19:47 -0400)]
i40e: remove BUG_ON from feature string building
There's really no reason to kill the kernel thread just because of a
little info string. This reworks the code to use snprintf's limiting to
assure that the string is never too long, and WARN_ON to still put out
a warning that we might want to look at the feature list length.
Prompted by a recent Linus diatribe.
Change-ID: If52ba5ca1c2344d8bf454a31bbb805eb5d2c5802 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 21 Oct 2015 23:47:03 +0000 (19:47 -0400)]
i40e: Change BUG_ON to WARN_ON in service event complete
There's no need to kill the thread and eventually the kernel in this
case. In fact, the remainder of the code won't hurt anything anyway,
so just complain that we're here and move along.
Prompted by a recent Linus diatribe.
Change-ID: Iec020d8bcfedffc1cd2553cc6905fd915bb3e670 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 21 Oct 2015 23:47:02 +0000 (19:47 -0400)]
i40e/i40evf: remove unused tunnel parameter
Code was moved into a separate function some time ago.
Change-ID: Icabbe71ce05cf5d716d3e1152cdd9cd41d11bcb5 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
projects / linux-beck.git / log