In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the m68k's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: m68k <linux-m68k@lists.linux-m68k.org> Cc: 3.2.x.. <stable@vger.kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
powerpc/mpc85xx: Add new ext fields to Integrated FLash Controller
Freescale's Integrated Flash controller(IFC) v1.1.0 supports 40 bit
address bus width.
In case more than 32 bit address is used, the EXT registers should be set.
Add support of ext registers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Olivia Yin [Thu, 9 Aug 2012 07:42:36 +0000 (15:42 +0800)]
powerpc/e5500: Add Power ISA properties to comply with ePAPR 1.1
power-isa-version and power-isa-* are cpu node general properties defined
in ePAPR.
If the power-isa-version property exists, then for each category from the
Categories section of Book I of the Power ISA version indicated, the
existence of a property named power-isa-[CAT], where [CAT] is the
abbreviated category name with all uppercase letters converted to
lowercase, indicates that the category is supported by the implementation.
This patch update all the e5500 platforms.
Signed-off-by: Liu Yu <yu.liu@freescale.com> Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Olivia Yin [Thu, 9 Aug 2012 07:42:35 +0000 (15:42 +0800)]
powerpc/e500mc: Add Power ISA properties to comply with ePAPR 1.1
power-isa-version and power-isa-* are cpu node general properties defined
in ePAPR.
If the power-isa-version property exists, then for each category from the
Categories section of Book I of the Power ISA version indicated, the
existence of a property named power-isa-[CAT], where [CAT] is the
abbreviated category name with all uppercase letters converted to
lowercase, indicates that the category is supported by the implementation.
The patch update all the e500mc platforms.
Signed-off-by: Liu Yu <yu.liu@freescale.com> Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Olivia Yin [Thu, 9 Aug 2012 07:42:34 +0000 (15:42 +0800)]
powerpc/e500v2: Add Power ISA properties to comply with ePAPR 1.1
power-isa-version and power-isa-* are cpu node general properties defined
in ePAPR.
If the power-isa-version property exists, then for each category from the
Categories section of Book I of the Power ISA version indicated, the
existence of a property named power-isa-[CAT], where [CAT] is the
abbreviated category name with all uppercase letters converted to
lowercase, indicates that the category is supported by the implementation.
The patch update all e500v2 platforms.
Signed-off-by: Liu Yu <yu.liu@freescale.com> Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Varun Sethi [Wed, 8 Aug 2012 04:06:09 +0000 (09:36 +0530)]
powerpc/mpic: FSL MPIC error interrupt support.
All SOC device error interrupts are muxed and delivered to the core
as a single MPIC error interrupt. Currently all the device drivers
requiring access to device errors have to register for the MPIC error
interrupt as a shared interrupt.
With this patch we add interrupt demuxing capability in the mpic driver,
allowing device drivers to register for their individual error interrupts.
This is achieved by handling error interrupts in a cascaded fashion.
MPIC error interrupt is handled by the "error_int_handler", which
subsequently demuxes it using the EISR and delivers it to the respective
drivers.
The error interrupt capability is dependent on the MPIC EIMR register,
which was introduced in FSL MPIC version 4.1 (P4080 rev2). So, error
interrupt demuxing capability is dependent on the MPIC version and can
be used for versions >= 4.1.
projects / karo-tx-linux.git / log