Maya Erez [Tue, 1 Mar 2016 17:18:05 +0000 (19:18 +0200)]
wil6210: AP: prevent connecting to already connected station
wmi_evt_connect doesn't check if the connect event is received for
an already connected station.
This can lead to memory leak as a new vring is allocated without
freeing the previously allocated vring and to unexpected behavior
of nl80211 layer due to unexpected notification of a new station.
Add a check in wmi_evt_connect in AP mode to verify that the requested
CID is not associated to an already connected station.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Maya Erez [Tue, 1 Mar 2016 17:18:04 +0000 (19:18 +0200)]
wil6210: remove BACK RX and TX workers
WMI synchronous handling has changed and WMI calls that provide
a buffer for the reply are completed in the WMI interrupt context.
This allows sending the RX and TX BACK commands from the WMI event
handler without the need for the worker thread.
This is a better approach as it can decrease the handshake time
in the connect flow and prevent race conditions in case of fast
disconnects. An example for such a race is handling of wil_back_rx_handle
during a disconnect event, as wil_back_rx_handle is not protected by
the wil mutex and a disconnect can be handled after sta->status is
verified as connected.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 166de3f1895d ("ath10k: remove supported chain mask") had revealed
an issue on monitor mode. Configuring NSS upon monitor interface
creation is causing target assert in all qca9888x and qca6174 firmware.
Firmware assert issue can be reproduced by below sequence even after
reverting commit 166de3f1895d ("ath10k: remove supported chain mask").
ip link set wlan0 down
iw wlan0 set type monitor
iw phy0 set antenna 7
ip link set wlan0 up
This issue is originally reported on qca9888 with 10.1 firmware.
Fixes: 5572a95b4b ("ath10k: apply chainmask settings to vdev on creation") Cc: stable@vger.kernel.org Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The number of HTT Tx descriptors and qcache peer
limit aren't hw-specific. In fact they are
firmware specific and should not be placed in
hw_params.
The QCA4019 limits were submitted with the peer
flow control firmware only and to my understanding
there's no non-peer-flow-ctrl QCA4019 firmware.
However QCA99X0 is planned to run firmware
supporting the feature as well. Therefore this
patch enables QCA99X0 to use 2500 tx descriptors
whenever possible instead of just 1424.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Tue, 1 Mar 2016 12:16:10 +0000 (13:16 +0100)]
ath10k: fix HTT Tx CE ring size
QCA4019 can queue up to 2500 frames at a time.
This means it requires roughly 5000 entires on the
ring to work properly. Otherwise random tx failure
may occur.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Sun, 6 Mar 2016 14:14:43 +0000 (16:14 +0200)]
ath10k: implement push-pull tx
The current/old tx path design was that host, at
its own leisure, pushed tx frames to the device.
For HTT there was ~1000-1400 msdu queue depth.
After reaching that limit the driver would request
mac80211 to stop queues. There was little control
over what packets got in there as far as
DA/RA was considered so it was rather easy to
starve per-station traffic flows.
With MU-MIMO this became a significant problem
because the queue depth was insufficient to buffer
frames from multiple clients (which could have
different signal quality and capabilities) in an
efficient fashion.
Hence the new tx path in 10.4 was introduced: a
pull-push mode.
Firmware and host can share tx queue state via
DMA. The state is logically a 2 dimensional array
addressed via peer_id+tid pair. Each entry is a
counter (either number of bytes or packets. Host
keeps it updated and firmware uses it for
scheduling Tx pull requests to host.
This allows MU-MIMO to become a lot more effective
with 10+ clients.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Sun, 6 Mar 2016 14:14:36 +0000 (16:14 +0200)]
ath10k: implement updating shared htt txq state
Firmware 10.4.3 onwards can support a pull-push Tx
model where it shares a Tx queue state with the
host.
The host updates the DMA region it pointed to
during HTT setup whenever number of software
queued from (on host) changes. Based on this
information firmware issues fetch requests to the
host telling the host how many frames from a list
of given stations/tids should be submitted to the
firmware.
The code won't be called because not all
appropriate HTT events are processed yet.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Sun, 6 Mar 2016 14:14:30 +0000 (16:14 +0200)]
ath10k: add fast peer_map lookup
The pull-push functionality of 10.4 will be based
on peer_id and tid. These will need to be mapped,
eventually, to ieee80211_txq to be used with
ieee80211_tx_dequeue().
Iterating over existing stations every time
peer_id needs to be mapped to a station would be
inefficient wrt CPU time.
The new firmware, which will be the only user of
the code flow-wise, will guarantee to use low
peer_ids first so despite peer_map's apparent huge
size d-cache thrashing should not be a problem.
Older firmware hot paths will effectively not use
peer_map.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Sun, 6 Mar 2016 14:14:27 +0000 (16:14 +0200)]
ath10k: maintain peer_id for each sta and vif
The 10.4.3 firmware with congestion control
guarantees that each peer has only a single
peer_id mapping.
The 1:1 mapping isn't the case for older firmwares
(e.g. 10.4.1, 10.2, 10.1) but it should not
matter. This 1:1 mapping is going to be only used
by future code which inherently (flow-wise) is for
10.4.3.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Sun, 6 Mar 2016 14:14:25 +0000 (16:14 +0200)]
ath10k: refactor tx pending management
Tx pending counter logic assumed that the sk_buff
is already known and hence was performed in HTT
functions themselves.
However, for the sake of future wake_tx_queue()
usage the driver must be able to tell whether it
can submit more frames to firmware before it
dequeues frame from ieee80211_txq (and thus long
before HTT Tx functions are called) because once a
frame is dequeued it cannot be requeud back to
mac80211.
This prepares the driver for future changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Zhang Shengju [Thu, 3 Mar 2016 01:16:57 +0000 (01:16 +0000)]
wireless: use reset to set mac header
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Thu, 3 Mar 2016 01:16:56 +0000 (01:16 +0000)]
mac80211: use reset to set header pointer
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Thu, 3 Mar 2016 01:16:55 +0000 (01:16 +0000)]
mac80211_hwsim: use reset to set mac header
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Thu, 3 Mar 2016 01:16:54 +0000 (01:16 +0000)]
vxlan: use reset to set header pointers
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add operation
in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 4 Mar 2016 22:19:16 +0000 (17:19 -0500)]
Merge tag 'rxrpc-rewrite-20160304' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
RxRPC: Rewrite part 1
Here's the first set of patches from my RxRPC rewrite, aimed at net-next.
These do some clean ups and bug fixes. Most of the changes are small, but
there are a couple of bigger changes:
(*) Convert call flag numbers and event numbers into enums. Then rename
the event numbers to all have _EV_ in their name to stop confusion.
Fix one instance of an event bit being used instead of a flag bit.
(*) A copy of the Rx protocol header is kept in the sk_buff private data.
Keep this in host byte order rather than network byte order as it
makes more sense. A number of other fields then get converted into
host byte order too.
Conversion between host and network byte order is then done at the
packet reception/generation stage.
This is based on net-next/master
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Fri, 4 Mar 2016 10:52:19 +0000 (11:52 +0100)]
ethtool.h: define INT_MAX for userland
INT_MAX needs limits.h in userland.
When ethtool.h is included by a userland app, we got the following error:
.../usr/include/linux/ethtool.h: In function 'ethtool_validate_speed':
.../usr/include/linux/ethtool.h:1471:18: error: 'INT_MAX' undeclared (first use in this function)
return speed <= INT_MAX || speed == SPEED_UNKNOWN
^
Fixes: e02564ee334a ("ethtool: make validate_speed accept all speeds between 0 and INT_MAX") CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Fri, 4 Mar 2016 10:52:17 +0000 (11:52 +0100)]
cxgb4i: don't redefine DIV_ROUND_UP
let's use the common definition to avoid the following warning during the
compilation:
drivers/scsi/cxgbi/cxgb4i/cxgb4i.c:161:0: warning: "DIV_ROUND_UP" redefined
#define DIV_ROUND_UP(n, d) (((n) + (d) - 1) / (d))
^
In file included from include/linux/list.h:8:0,
from include/linux/module.h:9,
from drivers/scsi/cxgbi/cxgb4i/cxgb4i.c:16:
include/linux/kernel.h:67:0: note: this is the location of the previous definition
#define DIV_ROUND_UP __KERNEL_DIV_ROUND_UP
^
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Let's add a common definition in uapi and use it everywhere.
Fixes: ac2c7ad0e5d6 ("net/ethtool: introduce a new ioctl for per queue setting") CC: Kan Liang <kan.liang@intel.com> Suggested-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Fri, 4 Mar 2016 06:58:07 +0000 (15:58 +0900)]
nfp: remove Rolf Neugebauer as co-maintainer
Rolf is no longer in his previous role at Netronome and as far as I know no
longer working on the NFP driver. Thus it does not seem appropriate for him
to be a co-maintainer anymore.
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Fri, 4 Mar 2016 15:58:06 +0000 (15:58 +0000)]
rxrpc: Use ACCESS_ONCE() when accessing circular buffer pointers
Use ACCESS_ONCE() when accessing the other-end pointer into a circular
buffer as it's possible the other-end pointer might change whilst we're
doing this, and if we access it twice, we might get some weird things
happening.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 4 Mar 2016 15:56:06 +0000 (15:56 +0000)]
rxrpc: Be more selective about the types of received packets we accept
Currently, received RxRPC packets outside the range 1-13 are rejected.
There are, however, holes in the range that should also be rejected - plus
at least one type we don't yet support - so reject these also.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 4 Mar 2016 15:55:32 +0000 (15:55 +0000)]
rxrpc: Fix defined range for /proc/sys/net/rxrpc/rx_mtu
The upper bound of the defined range for rx_mtu is being set in the same
member as the lower bound (extra1) rather than the correct place (extra2).
I'm not entirely sure why this compiles.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 4 Mar 2016 15:53:46 +0000 (15:53 +0000)]
rxrpc: Keep the skb private record of the Rx header in host byte order
Currently, a copy of the Rx packet header is copied into the the sk_buff
private data so that we can advance the pointer into the buffer,
potentially discarding the original. At the moment, this copy is held in
network byte order, but this means we're doing a lot of unnecessary
translations.
The reasons it was done this way are that we need the values in network
byte order occasionally and we can use the copy, slightly modified, as part
of an iov array when sending an ack or an abort packet.
However, it seems more reasonable on review that it would be better kept in
host byte order and that we make up a new header when we want to send
another packet.
To this end, rename the original header struct to rxrpc_wire_header (with
BE fields) and institute a variant called rxrpc_host_header that has host
order fields. Change the struct in the sk_buff private data into an
rxrpc_host_header and translate the values when filling it in.
This further allows us to keep values kept in various structures in host
byte order rather than network byte order and allows removal of some fields
that are byteswapped duplicates.
Signed-off-by: David Howells <dhowells@redhat.com>
David Ahern [Wed, 2 Mar 2016 19:30:07 +0000 (11:30 -0800)]
net: ipv6: Fix refcnt on host routes
Andrew and Ying Huang's test robot both reported usage count problems that
trace back to the 'keep address on ifdown' patch.
>From Andrew:
We execute CRIU test on linux-next. On the current linux-next kernel
they hangs on creating a network namespace.
The kernel log contains many massages like this:
[ 1036.122108] unregister_netdevice: waiting for lo to become free.
Usage count = 2
[ 1046.165156] unregister_netdevice: waiting for lo to become free.
Usage count = 2
[ 1056.210287] unregister_netdevice: waiting for lo to become free.
Usage count = 2
I tried to revert this patch and the bug disappeared.
Here is a set of commands to reproduce this bug:
[root@linux-next-test linux-next]# uname -a
Linux linux-next-test 4.5.0-rc6-next-20160301+ #3 SMP Wed Mar 2
17:32:18 UTC 2016 x86_64 x86_64 x86_64 GNU/Linux
[root@linux-next-test ~]# unshare -n
[root@linux-next-test ~]# ip link set up dev lo
[root@linux-next-test ~]# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
[root@linux-next-test ~]# logout
[root@linux-next-test ~]# unshare -n
-----
The problem is a change made to RTM_DELADDR case in __ipv6_ifa_notify that
was added in an early version of the offending patch and is no longer
needed.
Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional") Cc: Andrey Wagin <avagin@gmail.com> Cc: Ying Huang <ying.huang@linux.intel.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Tested-by: Jeremiah Mahler <jmmahler@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lada Trimasova [Thu, 3 Mar 2016 14:07:46 +0000 (17:07 +0300)]
net: ezchip: adapt driver to little endian architecture
Since ezchip network driver is written with big endian EZChip platform it
is necessary to add support for little endian architecture.
The first issue is that the order of the bits in a bit field is
implementation specific. So all the bit fields are removed.
Named constants are used to access necessary fields.
And the second one is that network byte order is big endian.
For example, data on ethernet is transmitted with most-significant
octet (byte) first. So in case of little endian architecture
it is important to swap data byte order when we read it from
register. In case of unaligned access we can use "get_unaligned_be32"
and in other case we can use function "ioread32_rep" which reads all
data from register and works either with little endian or big endian
architecture.
And then when we are going to write data to register we need to restore
byte order using the function "put_unaligned_be32" in case of
unaligned access and in other case "iowrite32_rep".
The last little fix is a space between type and pointer to observe
coding style.
Signed-off-by: Lada Trimasova <ltrimas@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Noam Camus <noamc@ezchip.com> Cc: Tal Zilcer <talz@ezchip.com> Cc: Arnd Bergmann <arnd@arndb.de> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Wed, 2 Mar 2016 01:28:13 +0000 (10:28 +0900)]
sh_eth, ravb: Use ARCH_RENESAS
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 2 Mar 2016 09:40:54 +0000 (10:40 +0100)]
net: mellanox: add DEVLINK dependencies
The new NET_DEVLINK infrastructure can be a loadable module, but the drivers
using it might be built-in, which causes link errors like:
drivers/net/built-in.o: In function `mlx4_load_one':
:(.text+0x2fbfda): undefined reference to `devlink_port_register'
:(.text+0x2fc084): undefined reference to `devlink_port_unregister'
drivers/net/built-in.o: In function `mlxsw_sx_port_remove':
:(.text+0x33a03a): undefined reference to `devlink_port_type_clear'
:(.text+0x33a04e): undefined reference to `devlink_port_unregister'
There are multiple ways to avoid this:
a) add 'depends on NET_DEVLINK || !NET_DEVLINK' dependencies
for each user
b) use 'select NET_DEVLINK' from each driver that uses it
and hide the symbol in Kconfig.
c) make NET_DEVLINK a 'bool' option so we don't have to
list it as a dependency, and rely on the APIs to be
stubbed out when it is disabled
d) use IS_REACHABLE() rather than IS_ENABLED() to check for
NET_DEVLINK in include/net/devlink.h
This implements a variation of approach a) by adding an
intermediate symbol that drivers can depend on, and changes
the three drivers using it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 09d4d087cd48 ("mlx4: Implement devlink interface") Fixes: c4745500e988 ("mlxsw: Implement devlink interface") Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Here's our main set of Bluetooth & 802.15.4 patches for the 4.6 kernel.
- New Bluetooth HCI driver for Intel/AG6xx controllers
- New Broadcom ACPI IDs
- LED trigger support for indicating Bluetooth powered state
- Various fixes in mac802154, 6lowpan and related drivers
- New USB IDs for AR3012 Bluetooth controllers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Mon, 29 Feb 2016 19:26:13 +0000 (11:26 -0800)]
net: relax setup_tc ndo op handle restriction
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
Miaoqing Pan [Thu, 18 Feb 2016 09:20:02 +0000 (17:20 +0800)]
ath9k: clear bb filter calibration power threshold
JP WiFi certification for bandwidth of channel 14 failed, the OBW
is lower than the requirement. Clear the bb filter calibration power
threshold to increase OBW(+2). The fix only for qca9531 chip now.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Arnd Bergmann [Fri, 12 Feb 2016 11:55:21 +0000 (12:55 +0100)]
ath9k: reduce stack usage in ar9003_aic_cal_post_process
In some configurations, this function uses more than the warning limit
of 1024 bytes:
drivers/net/wireless/ath/ath9k/ar9003_aic.c: In function 'ar9003_aic_cal_post_process':
drivers/net/wireless/ath/ath9k/ar9003_aic.c:434:1: error: the frame size of 1040 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
It turns out that there are two large arrays on the stack here, but
almost all the data in them is never used outside of the loop in
which it gets written, so we can replace the array with a single
instance.
The .valid flag is used later, so I'm replacing the array of structures
with an array of bools. An obvious follow-up optimization would be
to replace it with a bitmask and set_bit()/find_first_bit()/
find_last_bit()/... operations. However, I have not tested this patch,
so I sticked to the simpler transformation that does the job of
reducing the stack usage to a harmless level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Miaoqing Pan [Fri, 5 Feb 2016 01:45:50 +0000 (09:45 +0800)]
ath9k: make NF load complete quickly and reliably
Make NF load complete quickly and reliably. NF load execution
is delayed by HW to end of frame if frame Rx or Tx is ongoing.
Increasing timeout to max frame duration. If NF cal is ongoing
before NF load, stop it before load, and restart it afterwards.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: fix sanity check on enabling btcoex via debugfs
First check for the device state before enabling / disabling
btcoex, also return a proper error value. Enabling / disabling
btcoex ideally does a f/w + ath10k_core_restart so the checks
that are applicable for 'simulate_fw_crash' shall be applicable
for this as well
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Anilkumar Kolli [Tue, 23 Feb 2016 06:49:57 +0000 (12:19 +0530)]
ath10k: reduce number of peers to support peer stats feature
To enable per peer stats feature we are reducing the number of peers.
Firmware has introduced tx stats feature. We have memory limitation in
firmware to add these additional bytes.
These are the new variables introduced in the firmware.
======== =======================
Variable Bytes required/per rate
======== =======================
TX success packets 1
TX failed packets 1
Retry packets 1
Success bytes 2
TX failed bytes 2
Retry bytes 2
Tx duration 4
Rate 1
Bw and AMPDU flags 1
Total 16 (because of allocation in word pattern)
Firmware sends these tx_stats in pktlog.
If we consider 4 feedbacks at a time, Frimware need about ~1K memory for coding
and 8192 bytes required / per rate [ 4*16*128(peers)].
To accommodate this firmware needs to reduce 10 peers.
This fixes a firmware crash with firmware-5.bin_10.2.4.70.22-2.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On multicore systems, it is possible that txrx tasket can run
in parallel with pci tasklet (i.e smp affinity of ath10k irq is
assigned to multiple CPUs). Feeding and consuming from the same
rx completion list leads to txrx tasklet runs for longer period.
Prevent this by processing a snapshot of rx queue by moving list
into temporary list. Consecutive received frames will be processed
in next batch.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: reduce rx_lock contention for htt rx indication
Received frame indications are queued into a skb list and latest
processed by txrx tasklet. This skb queue is protected by htt rx lock.
Since the entire rx processing till delivering frame to mac80211 and
replenish tasks are processed under rx_lock protection, there might be
some delay in queuing newly received rx frame into that list on
multicore systems. Optimize this by using skb list lock while accessing
rx completion queue instead of htt rx lock.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: add hw_rev to trace events to support pktlog
pktlog data is different between firmware variants (eg. 10.2 vs 10.4). To
have a unified user space script to decode pktlog trace events generated,
it is desirable to know which firmware variant has provided the events and
thereby decode the pktlogs appropriately. Hardware revision (hw_rev) helps
to determine the firmware variant sending these trace events. So add hw_rev
to trace events.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently, we are providing wrong payload data of pktlog to trace points.
Data we receive from FW through copy engine 8 contains pktlog data alone.
We don't need to parse anything in driver before handing it to trace
points.
Fixes: afb0bf7f530b ("ath10k: add support for pktlog in QCA99X0") Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We periodically receive f/w stats event for updating
the rx duration and there is no reason to keep on appending
the f/w stats peer list, as this gets completely cleaned up when
the user polls for f/w stats {pdev, vdev, peer stats}. Only don't
print the warning message in the case PEER_STATS service is enabled
Fixes: 856e7c3 ("ath10k: add debugfs support for Per STA total rx duration") Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Eric Engestrom [Mon, 29 Feb 2016 16:38:06 +0000 (16:38 +0000)]
net/ipv4: remove left over dead code
8cc785f6f429c2a3fb81745dc142cbd72a462c4a ("net: ipv4: make the ping
/proc code AF-independent") removed the code using it, but renamed this
variable instead of removing it.
Signed-off-by: Eric Engestrom <eric.engestrom@imgtec.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 2 Mar 2016 19:46:30 +0000 (14:46 -0500)]
Merge branch 'cxgb4-next'
Hariprasad Shenai says:
====================
cxgb4/cxgb4vf: Cleanup and minor fixes
This series sets FBMIN to 64 bytes for Chelsio's T6 series of adapters,
check to replenish fl is revised, some code cleanup in cxgb4vf sge
initialization code and removes dead code.
This patch series has been created against net-next tree and includes
patches on cxgb4 and cxgb4vf driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
cxgb4/cxgb4vf: For T6 adapter, set FBMIN to 64 bytes
T4 and T5 hardware will not coalesce Free List PCI-E Fetch Requests if
the Host Driver provides more Free List Pointers than the Fetch Burst
Minimum value. So if we set FBMIN to 64 bytes and the Host Driver
supplies 128 bytes of Free List Pointer data, the hardware will issue two
64-byte PCI-E Fetch Requests rather than a single coallesced 128-byte
Fetch Request. T6 fixes this. So, for T4/T5 we set the FBMIN value to 128
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 2 Mar 2016 19:21:34 +0000 (14:21 -0500)]
Merge branch 'stmmac-optimizations'
Alexandre TORGUE says:
====================
stmmac: enhance driver performances and update the version
According to Giuseppe, I send the v3 series.
This is a subset of patches to rework the driver in order to improve its
performances and make it more robust under stress conditions.
All patches have been ported on STi mainstream kernel branch and
tested on ARM STiH4xx platforms and newer ones.
This series also updates the driver version and prepares it
to include further development to support new chips.
In detail, these patches are:
o to rework and improve the internal DMA bus settings
Fine tuning is mandatory on some platforms for both
performance and stability issues.
o to rework and optimize the descriptor management.
This will help a lot on performance side and preparing
the inclusion on the GMAC4.x.
o to add a set of optimizations for both xmit and rx functions.
These will help a lot on performance side and making the driver
more robust in case of low memory conditions and under some
stress test, performed for example on IP-STB.
Below some throughput figures obtained on some boxes before and after
the patches.
V2: - rx_copybreak is now managed by using ethtool.
V3: - improve comments on PCIe detailing that there are no regressions
- rework some APIs to properly define some params as bool as expected
- rework the formula to get the element inside the ring. Comparing V2,
patches 4 and 13 have been merged because the same formula have been
used. After this rework, no evident benefit has been noticed in terms
of performances so the table above is still valid. Disassembling the
code for SH4 and ARM, with the new formula just an instr is saved
(depending on compiler flags) and this gives us not so relevanti gain,
for example, on SH4 where some instr are executed in the same pipeline
stage.
Ring sizes are now fixed and maybe they can be reworked to be tuned
w/o using stmmaceth= cmdline option. Indeed, nobody change these sizes
and indeed the numbers selected by default respect the budget and
avoid to pass invalid setup. These are the best driver default sizes
for ring and chain.
This patch just updates the driver to the version fully
tested on STi platforms. This version is Oct_2015.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There is a threshold now used to also limit the skb allocation
when use zero-copy. This is to avoid that there are incoherence
in the ring due to a failure on skb allocation under very
aggressive testing and under low memory conditions.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allow this driver to copy tiny frames during the reception
process. This is giving more stability while stressing the driver on STi
embedded systems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fabrice Gasnier [Mon, 29 Feb 2016 13:27:40 +0000 (14:27 +0100)]
stmmac: fix phy init when attached to a phy
phy_bus_name can be NULL when "fixed-link" property isn't used.
Then, since "stmmac: do not poll phy handler when attach a switch",
phy_bus_name ptr needs to be checked before strcmp is called.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: do not poll phy handler when attach a switch
This patch avoids to call the stmmac_adjust_link when
the driver is connected to a switch by using the FIXED_PHY
support. Prior this patch the phydev->irq was set as PHY_POLL
so periodically the phy handler was invoked spending useless
time because the link cannot actually change.
Note that the stmmac_adjust_link will be called just one
time and this guarantees that the ST glue logic will be
setup according to the mode and speed fixed.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: first frame prep at the end of xmit routine
This patch is to fill the first descriptor just before granting
the DMA engine so at the end of the xmit.
The patch takes care about the algorithm adopted to mitigate the
interrupts, then it fixes the last segment in case of no fragments.
Moreover, this new implementation does not pass any "ter" field when
prepare the descriptors because this is not necessary.
The patch also details the memory barrier in the xmit.
As final results, this patch guarantees the same performances
but fixing a case if small datagram are sent. In fact, this
kind of test is impacted if no coalesce is done.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The dirty index can be updated out of the loop where all the
tx resources are claimed. This will help on performances too.
Also a useless debug printk has been removed from the main loop.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fabrice Gasnier [Mon, 29 Feb 2016 13:27:36 +0000 (14:27 +0100)]
stmmac: optimize tx clean function
This patch "inline" get_tx_owner and get_ls routines. It Results in a
unique read to tdes0, instead of three, to check TX_OWN and LS bits,
and other status bits.
It helps improve driver TX path by removing two uncached read/writes
inside TX clean loop for enhanced descriptors but not for normal ones
because the des1 must be read in any case.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to optimize the way to manage the TDES inside the
xmit function. When prepare the frame, some settings (e.g. OWN
bit) can be merged. This has been reworked to improve the tx
performances.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fabrice Gasnier [Mon, 29 Feb 2016 13:27:34 +0000 (14:27 +0100)]
stmmac: merge get_rx_owner into rx_status routine.
The RDES0 register can be read several times while doing RX of a
packet.
This patch slightly improves RX path performance by reading rdes0
once for two operation: check rx owner, get rx status bits.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize tx_clean by avoiding a des3 read in stmmac_clean_desc3().
In ring mode, TX, des3 seems only used when xmit a jumbo frame.
In case of normal descriptors, it may also be used for time
stamping.
Clean it in the above two case, without reading it.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
last_segment field is read twice from dma descriptors in stmmac_clean().
Add last_segment to dma data so that this flag is from priv
structure in cache instead of memory.
It avoids reading twice from memory for each loop in stmmac_clean().
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the code pulls out the length field when
unmapping a buffer directly from the descriptor. This will result
in an uncached read to a dma_alloc_coherent() region. There is no
need to do this, so this patch simply puts the value directly into
a data structure which will hit the cache.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to rework the ring management now optimized.
The indexes into the ring buffer are always incremented, and
the entry is accessed via doing a modulo to find the "real"
position in the ring.
It is inefficient, modulo is an expensive operation.
The formula [(entry + 1) & (size - 1)] is now adopted on
a ring that is power-of-2 in size.
Then, the number of elements cannot be set by command line but
it is fixed.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch completely changes the descriptor layout to improve
the whole performances due to the single read usage of the
descriptors in critical paths.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: rework DMA bus setting and introduce new platform AXI structure
This patch restructures the DMA bus settings and this is done
by introducing a new platform structure used for programming
the AXI Bus Mode Register inside the DMA module.
This structure can be populated from device-tree as documented in the
binding txt file.
After initializing the DMA, the AXI register can be optionally tuned
for platform drivers based.
This patch also reworks some parameters to make coherent the DMA
configuration now that AXI register is introduced.
For example, the burst_len is managed by using the mentioned axi
support above; so the snps,burst-len parameter has been removed.
It makes sense to provide the AAL parameter from DT to Address-Aligned
Beats inside the Register0 and review the PBL settings when initialize
the engine.
For PCI glue, rebuilding the story of this setting, it
was added to align a configuration so not for fixing some
known problem. No issue raised after this patch.
It is safe to use the default burst length instead of
tuning it to the maximum value
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: share reset function between dwmac100 and dwmac1000
This patch is to share the same reset procedure between dwmac100 and
dwmac1000 chips.
This will also help on enhancing the driver and support new chips.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 2 Mar 2016 19:13:20 +0000 (14:13 -0500)]
Merge branch 'rds-support-FRMR-and-cleanups'
Santosh Shilimkar says:
====================
RDS: Major clean-up with couple of new features for 4.6
v3:
Re-generated the same series by omitting "-D" option from git format-patch
command. Since first patch has file removals, git apply/am can't deal
with it when formated with '-D' option.
v2:
Dropped module parameter from [PATCH 11/13] as suggested by David Miller
Series is generated against net-next but also applies against Linus's tip
cleanly. Entire patchset is available at below git tree:
The diff-stat looks bit scary since almost ~4K lines of code is
getting removed. Brief summary of the series:
- Drop the stale iWARP support:
RDS iWarp support code has become stale and non testable for
sometime. As discussed and agreed earlier on list, am dropping
its support for good. If new iWarp user(s) shows up in future,
the plan is to adapt existing IB RDMA with special sink case.
- RDS gets SO_TIMESTAMP support
- Long due RDS maintainer entry gets updated
- Some RDS IB code refactoring towards new FastReg Memory registration (FRMR)
- Lastly the initial support for FRMR
RDS IB RDMA performance with FRMR is not yet as good as FMR and I do have
some patches in progress to address that. But they are not ready for 4.6
so I left them out of this series.
Also am keeping eye on new CQ API adaptations like other ULPs doing and
will try to adapt RDS for the same most likely in 4.7+ timeframe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Avinash Repaka [Tue, 1 Mar 2016 23:20:54 +0000 (15:20 -0800)]
RDS: IB: Support Fastreg MR (FRMR) memory registration mode
Fastreg MR(FRMR) is another method with which one can
register memory to HCA. Some of the newer HCAs supports only fastreg
mr mode, so we need to add support for it to have RDS functional
on them.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Avinash Repaka <avinash.repaka@oracle.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
RDS: IB: allocate extra space on queues for FRMR support
Fastreg MR(FRMR) memory registration and invalidation makes use
of work request and completion queues for its operation. Patch
allocates extra queue space towards these operation(s).
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Discovere Fast Memmory Registration support using IB device
IB_DEVICE_MEM_MGT_EXTENSIONS. Certain HCA might support just FRMR
or FMR or both FMR and FRWR. In case both mr type are supported,
default FMR is used.
Default MR is still kept as FMR against what everyone else
is following. Default will be changed to FRMR once the
RDS performance with FRMR is comparable with FMR. The
work is in progress for the same.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the RDS connection on RDMA_CM_EVENT_TIMEWAIT_EXIT so that
it can reconnect and resume.
While testing fastreg, this error happened in couple of tests but
was getting un-noticed.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Preperatory patch for FRMR support. From connection info,
we can retrieve cm_id which contains qp handled needed for
work request posting.
We also need to drop the RDS connection on QP error states
where connection handle becomes useful.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Keep fmr related filed in its own struct. Fastreg MR structure
will be added to the union.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
No functional changes. This is in preperation towards adding
fastreg memory resgitration support.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This helps to combine asynchronous fastreg MR completion handler
with send completion handler.
No functional change.
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Chien Yen <chien.yen@oracle.com> Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log