The IPoIB UD QP reports send completions to priv->send_cq, which is
usually left unarmed; it only gets armed when the number of
outstanding send requests reaches the size of the TX queue. This
arming is done only in the send path for the UD QP. However, when
sending CM packets, the net queue may be stopped for the same reasons
but no measures are taken to recover the UD path from a lockup.
Consider this scenario: a host sends high rate of both CM and UD
packets, with a TX queue length of N. If at some time the number of
outstanding UD packets is more than N/2 and the overall outstanding
packets is N-1, and CM sends a packet (making the number of
outstanding sends equal N), the TX queue will be stopped. When all
the CM packets complete, the number of outstanding packets will still
be higher than N/2 so the TX queue will not be restarted.
Fix this by calling ib_req_notify_cq() when the queue is stopped in
the CM path.
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While investigating a bug, I came across a possible bug in v9fs. The
problem is similar to the one reported for NFS by ASANO Masahiro in
http://lkml.org/lkml/2005/12/21/334.
v9fs_file_lock() will skip locks on file which has mode set to 02666.
This is a problem in cases where the mode of the file is changed after
a process has obtained a lock on the file. Such a lock will be skipped
during unlock and the machine will end up with a BUG in
locks_remove_flock().
v9fs_file_lock() should skip the check for mandatory locks when
unlocking a file.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In ocfs2_validate_gd_parent, we check bg_chain against the
cl_next_free_rec of the dinode. Actually in resize, we have
the chance of bg_chain == cl_next_free_rec. So add some
additional condition check for it.
I also rename paramter "clean_error" to "resize", since the
old one is not clearly enough to indicate that we should only
meet with this case in resize.
btw, the correpsonding bug is
http://oss.oracle.com/bugzilla/show_bug.cgi?id=1230.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Joel Becker <joel.becker@oracle.com> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ocfs2_set_acl() and ocfs2_init_acl() were setting i_mode on the in-memory
inode, but never setting it on the disk copy. Thus, acls were some times not
getting propagated between nodes. This patch fixes the issue by adding a
helper function ocfs2_acl_set_mode() which does this the right way.
ocfs2_set_acl() and ocfs2_init_acl() are then updated to call
ocfs2_acl_set_mode().
Signed-off-by: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Joel Becker <joel.becker@oracle.com> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dq_flags are modified non-atomically in do_set_dqblk via __set_bit calls and
atomically for example in mark_dquot_dirty or clear_dquot_dirty. Hence a
change done by an atomic operation can be overwritten by a change done by a
non-atomic one. Fix the problem by using atomic bitops even in do_set_dqblk.
Signed-off-by: Andrew Perepechko <andrew.perepechko@sun.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Intel Architecture Optimization Reference Manual states that a short
load that follows a long store to the same object will suffer a store
forwading penalty, particularly if the two accesses use different addresses.
Trivially, a long load that follows a short store will also suffer a penalty.
__downgrade_write() in rwsem incurs both penalties: the increment operation
will not be able to reuse a recently-loaded rwsem value, and its result will
not be reused by any recently-following rwsem operation.
A comment in the code states that this is because 64-bit immediates are
special and expensive; but while they are slightly special (only a single
instruction allows them), they aren't expensive: a test shows that two loops,
one loading a 32-bit immediate and one loading a 64-bit immediate, both take
1.5 cycles per iteration.
Fix this by changing __downgrade_write to use the same add instruction on
i386 and on x86_64, so that it uses the same operand size as all the other
rwsem functions.
Signed-off-by: Avi Kivity <avi@redhat.com>
LKML-Reference: <1266049992-17419-1-git-send-email-avi@redhat.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Sun, 17 Jan 2010, Ingo Molnar wrote:
>
> FYI, -tip testing found that these changes break the UML build:
>
> kernel/built-in.o: In function `__up_read':
> /home/mingo/tip/arch/x86/include/asm/rwsem.h:192: undefined reference to `call_rwsem_wake'
> kernel/built-in.o: In function `__up_write':
> /home/mingo/tip/arch/x86/include/asm/rwsem.h:210: undefined reference to `call_rwsem_wake'
> kernel/built-in.o: In function `__downgrade_write':
> /home/mingo/tip/arch/x86/include/asm/rwsem.h:228: undefined reference to `call_rwsem_downgrade_wake'
> kernel/built-in.o: In function `__down_read':
> /home/mingo/tip/arch/x86/include/asm/rwsem.h:112: undefined reference to `call_rwsem_down_read_failed'
> kernel/built-in.o: In function `__down_write_nested':
> /home/mingo/tip/arch/x86/include/asm/rwsem.h:154: undefined reference to `call_rwsem_down_write_failed'
> collect2: ld returned 1 exit status
Add lib/rwsem_64.o to the UML subarch objects to fix.
LKML-Reference: <alpine.LFD.2.00.1001171023440.13231@localhost.localdomain> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This one is much faster than the spinlock based fallback rwsem code,
with certain artifical benchmarks having shown 300%+ improvement on
threaded page faults etc.
Again, note the 32767-thread limit here. So this really does need that
whole "make rwsem_count_t be 64-bit and fix the BIAS values to match"
extension on top of it, but that is conceptually a totally independent
issue.
NOT TESTED! The original patch that this all was based on were tested by
KAMEZAWA Hiroyuki, but maybe I screwed up something when I created the
cleaned-up series, so caveat emptor..
Also note that it _may_ be a good idea to mark some more registers
clobbered on x86-64 in the inline asms instead of saving/restoring them.
They are inline functions, but they are only used in places where there
are not a lot of live registers _anyway_, so doing for example the
clobbers of %r8-%r11 in the asm wouldn't make the fast-path code any
worse, and would make the slow-path code smaller.
(Not that the slow-path really matters to that degree. Saving a few
unnecessary registers is the _least_ of our problems when we hit the slow
path. The instruction/cycle counting really only matters in the fast
path).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <alpine.LFD.2.00.1001121810410.17145@localhost.localdomain> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For x86-64, 32767 threads really is not enough. Change rwsem_count_t
to a signed long, so that it is 64 bits on x86-64.
This required the following changes to the assembly code:
a) %z0 doesn't work on all versions of gcc! At least gcc 4.4.2 as
shipped with Fedora 12 emits "ll" not "q" for 64 bits, even for
integer operands. Newer gccs apparently do this correctly, but
avoid this problem by using the _ASM_ macros instead of %z.
b) 64 bits immediates are only allowed in "movq $imm,%reg"
constructs... no others. Change some of the constraints to "e",
and fix the one case where we would have had to use an invalid
immediate -- in that case, we only care about the upper half
anyway, so just access the upper half.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <tip-bafaecd11df15ad5b1e598adc7736afcd38ee13d@git.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The fast version of the rwsems (the code that uses xadd) has
traditionally only worked on x86-32, and as a result it mixes different
kinds of types wildly - they just all happen to be 32-bit. We have
"long", we have "__s32", and we have "int".
To make it work on x86-64, the types suddenly matter a lot more. It can
be either a 32-bit or 64-bit signed type, and both work (with the caveat
that a 32-bit counter will only have 15 bits of effective write
counters, so it's limited to 32767 users). But whatever type you
choose, it needs to be used consistently.
This makes a new 'rwsem_counter_t', that is a 32-bit signed type. For a
64-bit type, you'd need to also update the BIAS values.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <alpine.LFD.2.00.1001121755220.17145@localhost.localdomain> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes gcc use the right register names and instruction operand sizes
automatically for the rwsem inline asm statements.
So instead of using "(%%eax)" to specify the memory address that is the
semaphore, we use "(%1)" or similar. And instead of forcing the operation
to always be 32-bit, we use "%z0", taking the size from the actual
semaphore data structure itself.
This doesn't actually matter on x86-32, but if we want to use the same
inline asm for x86-64, we'll need to have the compiler generate the proper
64-bit names for the registers (%rax instead of %eax), and if we want to
use a 64-bit counter too (in order to avoid the 15-bit limit on the
write counter that limits concurrent users to 32767 threads), we'll need
to be able to generate instructions with "q" accesses rather than "l".
Since this header currently isn't enabled on x86-64, none of that matters,
but we do want to use the xadd version of the semaphores rather than have
to take spinlocks to do a rwsem. The mm->mmap_sem can be heavily contended
when you have lots of threads all taking page faults, and the fallback
rwsem code that uses a spinlock performs abysmally badly in that case.
[ hpa: modified the patch to skip size suffixes entirely when they are
redundant due to register operands. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <alpine.LFD.2.00.1001121613560.17145@localhost.localdomain> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Set a new DM_UEVENT_GENERATED_FLAG when returning from ioctls to
indicate that a uevent was actually generated. This tells the userspace
caller that it may need to wait for the event to be processed.
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
arch/x86/built-in.o: In function `store_cache_disable':
intel_cacheinfo.c:(.text+0xc509): undefined reference to `amd_get_nb_id'
arch/x86/built-in.o: In function `show_cache_disable':
intel_cacheinfo.c:(.text+0xc7d3): undefined reference to `amd_get_nb_id'
when CONFIG_CPU_SUP_AMD is not enabled because the amd_get_nb_id
helper is defined in AMD-specific code but also used in generic code
(intel_cacheinfo.c). Reorganize the L3 cache index disable code under
CONFIG_CPU_SUP_AMD since it is AMD-only anyway.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100218184210.GF20473@aftab> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The show/store_cache_disable routines depend unnecessarily on NUMA's
cpu_to_node and the disabling of cache indices broke when !CONFIG_NUMA.
Remove that dependency by using a helper which is always correct.
While at it, enable L3 Cache Index disable on rev D1 Istanbuls which
sport the feature too.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100218184339.GG20473@aftab> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to know the valid L3 indices interval when disabling them over
/sysfs. Do that when the core is brought online and add boundary checks
to the sysfs .store attribute.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1264172467-25155-6-git-send-email-bp@amd64.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Dave Jones <davej@redhat.com> Cc: David Airlie <airlied@linux.ie> Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1264172467-25155-3-git-send-email-bp@amd64.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Correct the masks used for writing the cache index disable indices.
* Do not turn off L3 scrubber - it is not necessary.
* Make sure wbinvd is executed on the same node where the L3 is.
* Check for out-of-bounds values written to the registers.
* Make show_cache_disable hex values unambiguous
* Check for Erratum #388
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1264172467-25155-4-git-send-email-bp@amd64.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add wbinvd_on_cpu and wbinvd_on_all_cpus stubs for executing wbinvd on a
particular CPU.
[ hpa: renamed lib/smp.c to lib/cache-smp.c ]
[ hpa: wbinvd_on_all_cpus() returns int, but wbinvd() returns
void. Thus, the former cannot be a macro for the latter,
replace with an inline function. ]
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1264172467-25155-2-git-send-email-bp@amd64.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disabling the IOMMU can potetially allow DMA transactions to
complete without being translated. Leave it enabled, and allow
crash kernel to do the IOMMU reinitialization properly.
Cc: Joerg Roedel <joerg.roedel@amd.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Neil Horman <nhorman@tuxdriver.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hit another kdump problem as reported by Neil Horman. When initializaing
the IOMMU, we attach devices to their domains before the IOMMU is
fully (re)initialized. Attaching a device will issue some important
invalidations. In the context of the newly kexec'd kdump kernel, the
IOMMU may have stale cached data from the original kernel. Because we
do the attach too early, the invalidation commands are placed in the new
command buffer before the IOMMU is updated w/ that buffer. This leaves
the stale entries in the kdump context and can renders device unusable.
Simply enable the IOMMU before we do the attach.
Cc: Neil Horman <nhorman@tuxdriver.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the amd_iommu_domain_destroy the protection_domain_free
function is partly reimplemented. The 'partly' is the bug
here because the domain is not deleted from the domain list.
This results in use-after-free errors and data-corruption.
Fix it by just using protection_domain_free instead.
After a guest is shutdown, assigned devices are not properly
returned to the pt domain. This can leave the device using
stale cached IOMMU data, and result in a non-functional
device after it's re-bound to the host driver. For example,
I see this upon rebinding:
Typo in in flush leaded to no flush of the RS600 tlb which
ultimately leaded to massive system ram corruption, with
this patch everythings seems to work properly.
On systems with the tv dac shared between DVI and TV,
we can only use the dac for one of the connectors.
However, when using a digital monitor on the DVI port,
you can use the dac for the TV connector just fine.
Check the use_digital status when resolving the conflict.
Fixes fdo bug 27649, possibly others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When CONFIG_REGULATOR isn't set, regulator_get_voltage() returns 0.
Properly handle this case by not trusting the value.
Reported-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I discovered two issues.
First the previous sht15_calc_temp() loop did not iterate through the
temppoints array since the (data->supply_uV > temppoints[i - 1].vdd)
test is always true in this direction.
Also the two-points linear interpolation function was returning biased
values due to a stray division by 1000 which shouldn't be there.
[JD: Also change the default value for d1 from 0 to something saner.]
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb-midi causes sometimes Oops at snd_usbmidi_output_drain() after
disconnection. This is due to the access to the endpoints which have
been already released at disconnection while the files are still alive.
This patch fixes the problem by checking disconnection state at
snd_usbmidi_output_drain() and by releasing urbs but keeping the
endpoint instances until really all freed.
When Wacom devices wake up from a sleep, the switch mode command
(wacom_query_tablet_data) is needed before wacom_open is called.
wacom_query_tablet_data should not be executed inside wacom_open
since wacom_open is called more than once during probe.
wacom_retrieve_hid_descriptor is removed from wacom_resume due
to the fact that the required descriptors are stored properly
upon system resume.
Arnaud Giersch reports that NFSv4 locking is broken when we hold a
delegation since commit 8e469ebd6dc32cbaf620e134d79f740bf0ebab79 (NFSv4:
Don't allow posix locking against servers that don't support it).
According to Arnaud, the lock succeeds the first time he opens the file
(since we cannot do a delegated open) but then fails after we start using
delegated opens.
The following patch fixes it by ensuring that locking behaviour is
governed by a per-filesystem capability flag that is initially set, but
gets cleared if the server ever returns an OPEN without the
NFS4_OPEN_RESULT_LOCKTYPE_POSIX flag being set.
Jan Grossmann reported kernel boot panic while booting SMP
kernel on his system with a single core cpu. SMP kernels call
enable_IR_x2apic() from native_smp_prepare_cpus() and on
platforms where the kernel doesn't find SMP configuration we
ended up again calling enable_IR_x2apic() from the
APIC_init_uniprocessor() call in the smp_sanity_check(). Thus
leading to kernel panic.
Don't call enable_IR_x2apic() and default_setup_apic_routing()
from APIC_init_uniprocessor() in CONFIG_SMP case.
NOTE: this kind of non-idempotent and assymetric initialization
sequence is rather fragile and unclean, we'll clean that up
in v2.6.35. This is the minimal fix for v2.6.34.
On Wed, Feb 24, 2010 at 03:37:04PM -0800, Justin Piszcz wrote:
> Hello,
>
> Again, on the Intel DP55KG board:
>
> # uname -a
> Linux host 2.6.33 #1 SMP Wed Feb 24 18:31:00 EST 2010 x86_64 GNU/Linux
>
> [ 1.237600] ------------[ cut here ]------------
> [ 1.237890] WARNING: at arch/x86/kernel/hpet.c:404 hpet_next_event+0x70/0x80()
> [ 1.238221] Hardware name:
> [ 1.238504] hpet: compare register read back failed.
> [ 1.238793] Modules linked in:
> [ 1.239315] Pid: 0, comm: swapper Not tainted 2.6.33 #1
> [ 1.239605] Call Trace:
> [ 1.239886] <IRQ> [<ffffffff81056c13>] ? warn_slowpath_common+0x73/0xb0
> [ 1.240409] [<ffffffff81079608>] ? tick_dev_program_event+0x38/0xc0
> [ 1.240699] [<ffffffff81056cb0>] ? warn_slowpath_fmt+0x40/0x50
> [ 1.240992] [<ffffffff81079608>] ? tick_dev_program_event+0x38/0xc0
> [ 1.241281] [<ffffffff81041ad0>] ? hpet_next_event+0x70/0x80
> [ 1.241573] [<ffffffff81079608>] ? tick_dev_program_event+0x38/0xc0
> [ 1.241859] [<ffffffff81078e32>] ? tick_handle_oneshot_broadcast+0xe2/0x100
> [ 1.246533] [<ffffffff8102a67a>] ? timer_interrupt+0x1a/0x30
> [ 1.246826] [<ffffffff81085499>] ? handle_IRQ_event+0x39/0xd0
> [ 1.247118] [<ffffffff81087368>] ? handle_edge_irq+0xb8/0x160
> [ 1.247407] [<ffffffff81029f55>] ? handle_irq+0x15/0x20
> [ 1.247689] [<ffffffff810294a2>] ? do_IRQ+0x62/0xe0
> [ 1.247976] [<ffffffff8146be53>] ? ret_from_intr+0x0/0xa
> [ 1.248262] <EOI> [<ffffffff8102f277>] ? mwait_idle+0x57/0x80
> [ 1.248796] [<ffffffff8102645c>] ? cpu_idle+0x5c/0xb0
> [ 1.249080] ---[ end trace db7f668fb6fef4e1 ]---
>
> Is this something Intel has to fix or is it a bug in the kernel?
This is a chipset erratum.
Thomas: You mentioned we can retain this check only for known-buggy and
hpet debug kind of options. But here is the simple workaround patch for
this particular erratum.
Some chipsets have a erratum due to which read immediately following a
write of HPET comparator returns old comparator value instead of most
recently written value.
Erratum 15 in
"Intel I/O Controller Hub 9 (ICH9) Family Specification Update"
(http://www.intel.com/assets/pdf/specupdate/316973.pdf)
Workaround for the errata is to read the comparator twice if the first
one fails.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <20100225185348.GA9674@linux-os.sc.intel.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We found a system where the MP table MPC and MPF structures overlap.
That doesn't really matter because the mptable is not used anyways with ACPI,
but it leads to a panic in the early allocator due to the overlapping
reservations in 2.6.33.
Earlier kernels handled this without problems.
Simply change these reservations to reserve_early_overlap_ok to avoid
the panic.
Reported-by: Thomas Renninger <trenn@suse.de> Tested-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <20100329074111.GA22821@basil.fritz.box> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Colin King reported a strange oops in S4 resume code path (see below). The test
system has i5/i7 CPU. The kernel doesn't open PAE, so 4M page table is used.
The oops always happen a virtual address 0xc03ff000, which is mapped to the
last 4k of first 4M memory. Doing a global tlb flush fixes the issue.
Tested-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Shaohua Li <shaohua.li@intel.com>
LKML-Reference: <20100305005932.GA22675@sli10-desk.sh.intel.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
98e12b5a6e05413 ("ARM: Fix decompressor's kernel size estimation for
ROM=y") broke the Thumb-2 decompressor because it added an entry in the
LC0 table but didn't adjust the offset the Thumb-2 code uses to load the
SP from that table. Fix it.
Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
changes:
v2 Added missing break (Johannes)
v3 Broke original patch into two (Johannes)
Signed-off-by: Javier Cardona <javier@cozybit.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With the enable_radio being uninitialized, ath_radio_enable() might be
called twice, which can leave some hardware in an undefined state.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
By doing this we always overwrite nbytes value that is being passed on to
CIFSSMBWrite() and need not rely on the callers to initialize. CIFSSMBWrite2 is
doing this already.
Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Reviewed-by: Jeff Layton <jlayton@samba.org> Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While chasing a bug report involving a OS/2 server, I noticed the server sets
pSMBr->CountHigh to a incorrect value even in case of normal writes. This
results in 'nbytes' being computed wrongly and triggers a kernel BUG at
mm/filemap.c.
Why the server is setting 'CountHigh' is not clear but only does so after
writing 64k bytes. Though this looks like the server bug, the client side
crash may not be acceptable.
The workaround is to mask off high 16 bits if the number of bytes written as
returned by the server is greater than the bytes requested by the client as
suggested by Jeff Layton.
Reviewed-by: Jeff Layton <jlayton@samba.org> Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 6a985c6194017de2c062916ad1cd00dee0302c40
([S390] s390: use change recording override for kernel mapping)
deactivated the change bit recording for the kernel mapping to
improve the performance. This works most of the time, but there
are cases (e.g. kernel runs in home space, futex atomic compare xcmg)
where we modify user memory with the kernel mapping instead of the
user mapping.
Instead of fixing these cases, this patch just deactivates change bit
override to avoid future problems with other kernel code that might
use the kernel mapping for user memory.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thank you for contacting us. We know that with our M225 line of SSDs
you sometimes need to disable NCQ (native command queuing) to avoid
just the type of errors you're seeing. Our recommendation for the
M225 is to add libata.force=noncq to your Linux kernel boot options,
under the kernel ATA library option.
I have sent your feedback to the engineers working on the C300, and
asked them to please pass it on to the firmware team. I have been
notified that they are in the process of testing and finalizing a
new firmware version, that you can expect to see released around the
end of April. We’ll keep you posted as to when it will be available
for download.
So, turn off NCQ on the drive w/ the current firmware revision.
Reported in the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=15573
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: lethalwp@scarlet.be Reported-by: Luke Macken <lmacken@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/551606
The OR's hardware distorts at PCM 100% because it does not correspond to
0 dB. Fix this in patch_ad1981() for all models using the Thinkpad
quirk.
Reported-by: Jane Silber Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original code doesn't take into consideration that the value of
MIXART_BA0_SIZE - pos can be less than zero which would lead to a large
unsigned value for "count".
Also I moved the check that read size is a multiple of 4 bytes below
the code that adjusts "count".
DECLARE_KFIFO creates a union with a struct kfifo and a buffer array with
size [size + sizeof(struct kfifo)].
INIT_KFIFO then sets the buffer pointer in struct kfifo to point to the
beginning of the buffer array which means that the first call to kfifo_in
will overwrite members of the struct kfifo.
Signed-off-by: David Härdeman <david@hardeman.nu> Acked-by: Stefani Seibold <stefani@seibold.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We now call through generic_file_aio_write -> generic_write_sync ->
vfs_fsync_range. vfs_fsync_range has:
if (!fop || !fop->fsync) {
ret = -EINVAL;
goto out;
}
But drivers/char/raw.c doesn't set an fsync method.
We have two options: fix it or remove the raw driver completely. I'm
happy to do either, the fact this has been broken for so long suggests it
is rarely used.
The patch below adds an fsync method to the raw driver. My knowledge of
the block layer is pretty sketchy so this could do with a once over.
If we instead decide to remove the raw driver, this patch might still be
useful as a backport to 2.6.33 and 2.6.32.
Signed-off-by: Anton Blanchard <anton@samba.org> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Christoph Hellwig <hch@lst.de> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jens Axboe <jens.axboe@oracle.com> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Tested-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Network folks reported that directing all MSI-X vectors of their multi
queue NICs to a single core can cause interrupt stack overflows when
enough interrupts fire at the same time.
This is caused by the fact that we run interrupt handlers by default
with interrupts enabled unless the driver reuqests the interrupt with
the IRQF_DISABLED set. The NIC handlers do not set this flag, so
simultaneous interrupts can nest unlimited and cause the stack
overflow.
The only safe counter measure is to run the interrupt handlers with
interrupts disabled. We can't switch to this mode in general right
now, but it is safe to do so for MSI interrupts.
Force IRQF_DISABLED for MSI interrupt handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andi Kleen <andi@firstfloor.org> Cc: Linus Torvalds <torvalds@osdl.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: David Miller <davem@davemloft.net> Cc: Greg Kroah-Hartman <gregkh@suse.de> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These just represent the secondary and further heads attached to the
card, and they have different sets of PCI bar registers to map.
So don't try to drive them in the main driver.
Reported-by: Frans van Berckel <fberckel@xs4all.nl> Tested-by: Frans van Berckel <fberckel@xs4all.nl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When there is a need to restart/reconfig hw, tear down all the
aggregation queues and let the mac80211 and driver get in-sync to have
the opportunity to re-establish the aggregation queues again.
Need to wait until driver re-establish all the station information before tear
down the aggregation queues, driver(at least iwlwifi driver) will reject the
stop aggregation queue request if station is not ready. But also need to make
sure the aggregation queues are tear down before waking up the queues, so
mac80211 will not sending frames with aggregation bit set.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"mac80211: fix skb buffering issue" still left a race
between enabling the hardware queues and the virtual
interface queues. In hindsight it's totally obvious
that enabling the netdev queues for a hardware queue
when the hardware queue is enabled is wrong, because
it could well possible that we can fill the hw queue
with packets we already have pending. Thus, we must
only enable the netdev queues once all the pending
packets have been processed and sent off to the device.
In testing, I haven't been able to trigger this race
condition, but it's clearly there, possibly only when
aggregation is being enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1st) a PREQ should only be processed, if it has the same SN and better
metric (instead of better or equal).
2nd) next_hop[ETH_ALEN] now actually used to buffer
mpath->next_hop->sta.addr for use out of lock.
Signed-off-by: Marco Porsch <marco.porsch@siemens.com> Acked-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An int urb is constructed but we fill it in with a bulk pipe type.
Commit f661c6f8c67bd55e93348f160d590ff9edf08904 implemented a pipe type
check when CONFIG_USB_DEBUG is enabled. The check failed for all the ar9170
usb transfers and the driver could not configure the wifi dongle.
This went unnoticed until now because most people don't have
CONFIG_USB_DEBUG enabled.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IWL_RATE_COUNT is 13 and IWL_RATE_COUNT_LEGACY is 12.
IWL_RATE_COUNT_LEGACY is the right one here because iwl3945_rates
doesn't support 60M and also that's how "rates" is defined in
iwlcore_init_geos() from drivers/net/wireless/iwlwifi/iwl-core.c.
Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the cgroup freezer is used to freeze tasks we do not want to thaw
those tasks during resume. Currently we test the cgroup freezer
state of the resuming tasks to see if the cgroup is FROZEN. If so
then we don't thaw the task. However, the FREEZING state also indicates
that the task should remain frozen.
This also avoids a problem pointed out by Oren Ladaan: the freezer state
transition from FREEZING to FROZEN is updated lazily when userspace reads
or writes the freezer.state file in the cgroup filesystem. This means that
resume will thaw tasks in cgroups which should be in the FROZEN state if
there is no read/write of the freezer.state file to trigger this
transition before suspend.
NOTE: Another "simple" solution would be to always update the cgroup
freezer state during resume. However it's a bad choice for several reasons:
Updating the cgroup freezer state is somewhat expensive because it requires
walking all the tasks in the cgroup and checking if they are each frozen.
Worse, this could easily make resume run in N^2 time where N is the number
of tasks in the cgroup. Finally, updating the freezer state from this code
path requires trickier locking because of the way locks must be ordered.
Instead of updating the freezer state we rely on the fact that lazy
updates only manage the transition from FREEZING to FROZEN. We know that
a cgroup with the FREEZING state may actually be FROZEN so test for that
state too. This makes sense in the resume path even for partially-frozen
cgroups -- those that really are FREEZING but not FROZEN.
Reported-by: Oren Ladaan <orenl@cs.columbia.edu> Signed-off-by: Matt Helsley <matthltc@us.ibm.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is required to call hw_breakpoint_init() on an attr before using it
in any other calls. This fixes the problem where kgdb will sometimes
fail to initialize on x86_64.
We could be failing/stopping a connection due to libiscsi starting
recovery/cleanup, but the xmit path or scsi eh thread path
could be dropping the connection at the same time.
As a result the session->state gets set to failed instead of in
recovery. We end up not blocking the session
and so the replacement timeout never gets started and we only end up
failing the IO when scsi_softirq_done sees that the
cmd has been running for (cmd->allowed + 1) * rq->timeout secs.
We used to fail the IO right away so users are seeing a long
delay when using dm-multipath. This problem was added in
2.6.28.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The error label releases the lock before calling journal_release_error,
but it requires that the lock be held. do_journal_release unlocks and
retakes it. When it releases it without it held, we trigger a BUG().
The error_alloc label skips the unlock since the lock isn't held yet
but none of the other conditions that are clean up exist yet either.
This patch returns immediately after the kzalloc failure and moves
the reiserfs_write_unlock after the journal_release_error call.
This was reported in https://bugzilla.novell.com/show_bug.cgi?id=591807
Reported-by: Thomas Siedentopf <thomas.siedentopf@novell.com> Signed-off-by: Jeff Mahoney <jeffm@suse.com> Cc: Thomas Siedentopf <thomas.siedentopf@novell.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For the boot, enable_mmu() is called from setup_arch() but we don't call
setup_arch() for any of the other cpus. So turn on the non-boot cpu's
mmu inside of start_secondary().
I noticed this bug on an SMP board when trying to map I/O memory
(smsc911x registers) into the kernel address space. Since the Address
Translation bit in MMUCR wasn't set, accessing the virtual address where
the smsc911x registers were supposedly mapped actually performed a
physical address access.
Signed-off-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace a BUG_ON with an error code in the event that the inode mapping
changes between calls to drm_open. This may happen for instance if udev
is loaded subsequent to the original opening of the device:
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drm/radeon/kms: Fix NULL pointer dereference if memory allocation failed in a simple way
> From: Pauli Nieminen <suokkos@gmail.com>
> Date: Fri, 19 Mar 2010 07:44:33 +0000
> Subject: drm/radeon/kms: Fix NULL pointer dereference if memory allocation failed.
>
> From: Pauli Nieminen <suokkos@gmail.com>
>
> commit fcbc451ba1948fba967198bd150ecbd10bbb7075 upstream.
>
> When there is allocation failure in radeon_cs_parser_relocs parser->nrelocs
> is not cleaned. This causes NULL pointer defeference in radeon_cs_parser_fini
> when clean up code is trying to loop over the relocation array and free the
> objects.
>
> Fix adds a check for a possible NULL pointer in clean up code.
[...]
This patch breaks compiling kernel 2.6.33 + the current stable queue:
CC [M] drivers/gpu/drm/radeon/radeon_cs.o
/tmp/buildd/linux-sidux-2.6-2.6.33/debian/build/source_amd64_none/drivers/gpu/drm/radeon/radeon_cs.c: In function 'radeon_cs_parser_fini':
/tmp/buildd/linux-sidux-2.6-2.6.33/debian/build/source_amd64_none/drivers/gpu/drm/radeon/radeon_cs.c:200: error: implicit declaration of function 'drm_gem_object_unreference_unlocked'
make[6]: *** [drivers/gpu/drm/radeon/radeon_cs.o] Error 1
as it depends on the introduction of drm_gem_object_unreference_unlocked()
in:
This patch introduces the drm_gem_object_unreference_unlocked
and drm_gem_object_handle_unreference_unlocked functions that
do not require holding struct_mutex.
drm_gem_object_unreference_unlocked calls the new
->gem_free_object_unlocked entry point if available, and
otherwise just takes struct_mutex and just calls ->gem_free_object
Use drm_gem_object_[handle_]unreference_unlocked where possible
Mostly obvious simplifications.
The i915 pread/pwrite ioctls, intel_overlay_put_image and
nouveau_gem_new were incorrectly using the locked versions
without locking: this is also fixed in this patch.
which don't really look like candidates for 2.6.33-stable.
> --- a/drivers/gpu/drm/radeon/radeon_cs.c
> +++ b/drivers/gpu/drm/radeon/radeon_cs.c
> @@ -193,11 +193,13 @@ static void radeon_cs_parser_fini(struct
> radeon_bo_list_fence(&parser->validated, parser->ib->fence);
> }
> radeon_bo_list_unreserve(&parser->validated);
> - for (i = 0; i < parser->nrelocs; i++) {
> - if (parser->relocs[i].gobj) {
> - mutex_lock(&parser->rdev->ddev->struct_mutex);
> - drm_gem_object_unreference(parser->relocs[i].gobj);
> - mutex_unlock(&parser->rdev->ddev->struct_mutex);
> + if (parser->relocs != NULL) {
^ the only important part, the rest merely covers the new indentation
level
> + for (i = 0; i < parser->nrelocs; i++) {
> + if (parser->relocs[i].gobj) {
> + mutex_lock(&parser->rdev->ddev->struct_mutex);
> + drm_gem_object_unreference_unlocked(parser->relocs[i].gobj);
^ drm_gem_object_unreference_unlocked() doesn't exist in 2.6.33, yet
we can use drm_gem_object_unreference() instead.
As a consequence, I'd suggest to merely backport the NULL pointer check,
while ignoring the simplification of using the newly introduced
drm_gem_object_unreference_unlocked() from 2.6.34:
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Cc: Pauli Nieminen <suokkos@gmail.com> Cc: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
RS4xx+ IGP chips use an internal gart, however,
some of them have the agp cap bits set in their pci
configs. Make sure to clear the AGP flag as AGP will
not work with them.
Should fix fdo bug 27225
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
proc_oom_score(task) has a reference to task_struct, but that is all.
If this task was already released before we take tasklist_lock
- we can't use task->group_leader, it points to nowhere
- it is not safe to call badness() even if this task is
->group_leader, has_intersects_mems_allowed() assumes
it is safe to iterate over ->thread_group list.
- even worse, badness() can hit ->signal == NULL
Add the pid_alive() check to ensure __unhash_process() was not called.
Also, use "task" instead of task->group_leader. badness() should return
the same result for any sub-thread. Currently this is not true, but
this should be changed anyway.
When using the string representation of a random counter as part of the base
name, ensure that it is no longer than 4 bytes.
Since we are repeatedly decrementing the counter in a loop until we have found a
unique base name, the counter may wrap around zero; therefore, it is not enough
to mask its higher bits before entering the loop, this must be done inside the
loop.
Now the EDID property will be updated when the corresponding EDID can be
obtained from the external display device. But after the external device
is plugged-out, the EDID property is not updated. In such case we still
get the corresponding EDID property although it is already detected as
disconnected.
gfs2_lock() will skip locks on file which have mode set to 02666. This is a problem in cases where the mode of the file is changed after a process has obtained a lock on the file. Such a lock will be skipped and will result in a BUG in locks_remove_flock().
gfs2_lock() should skip the check for mandatory locks when unlocking a file.
projects / karo-tx-linux.git / log