usb: musb: register nop transceiver driver for jz4740
Following the name change of the NOP transceiver driver in commit 4525bee (usb: phy: rename usb_nop_xceiv to usb_phy_generic), the
transceiver driver was no longer operable under its old name.
Register the transceiver driver before calling usb_get_phy() to make
sure we are noticed by an error message if it is not available.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: pxa25x_udc: use correct header for gpio devm_ functions
commit c63d2225e7be ("usb: gadget: pxa25x_udc: use devm_ functions")
introduced the use of devm_gpio_request in this driver, but did not
correctly include the header file declaring this function, which
causes a build failure.
This changes pxa25x_udc to include linux/gpio.h instead of asm/gpio.h
to fix this.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Himangi Saraogi <himangi774@gmail.com> Cc: Julia Lawall <julia.lawall@lip6.fr> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: renesas_usbhs: gadget: fix re-enabling pipe without re-connecting
This patch fixes an issue that the renesas_usbhs driver in gadget mode
cannot work correctly even if I disabled DMAC of the driver when I used
the g_zero driver and the testusb tool.
When a usb cable is re-connected, the renesas_usbhs driver calls the
usbhsp_flags_init() (via usbhs_hotplug() --> usbhs_mod_call(start) -->
usbhsg_try_start() --> usbhs_pipe_init()). However, the driver doesn't
call the usbhsp_flags_init() when usbhsg_ep_disable() is called.
So, if a gadget driver calls usb_ep_enable() and usb_ep_disable() again
and again, the renesas_usbhs driver will output the following log:
Daniel Mack [Thu, 19 Jun 2014 22:20:44 +0000 (00:20 +0200)]
usb: musb: cppi41: fire hrtimer according to programmed channel length
The musb/cppi41 code installs a hrtimer to work around DMA completion
interrupts that have fired too early on AM335x hardware. This timer
is currently programmed to first fire 140 microseconds after the DMA
completion callback. According to the commit which introduced it
(a655f481d83, "usb: musb: musb_cppi41: handle pre-mature TX complete
interrupt"), that value is is considered a 'rule of thumb' that worked
well with the test case described in the commit log.
Test show, however, that for USB audio devices and much smaller packet
sizes, the timer has to fire earlier in order to correctly handle the audio
stream. The original test case had output transfer sizes of 1514 bytes, and
a delay of 140 microseconds. For audio devices with 24 bytes channel size, 3
microseconds seem to work well.
Hence, let's assume that the time it takes to clear the bit correlates with
the number of bytes transferred. The referenced commit log mentions such a
suspicion as well. Let the timer fire in cppi41_channel->total_len/10
microseconds to correctly handle both cases.
Also, shorten the interval in which the timer fires again in case of
a non-empty early_tx list.
With these changes in place, both FS and HS audio devices appear to work
well on AM335x hardware.
Signed-off-by: Daniel Mack <zonque@gmail.com> Reported-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
The commit tried to address cases in which isochronous transfers are 'not
reliable', most probably in the tests conducted, polling for the
MUSB_TXCSR_TXPKTRDY bit in MUSB_TXCSR is done too late.
Hence, it installs a work struct which basically busy-polls for the bit in a
rather agressive way by rescheduling the work if the FIFO is not empty. With
USB audio devices, tests have shown that it takes approximately 100
iterations of the asynchronous worker until the FIFO signals completion,
which leads to 100% CPU loads when streaming audio.
The issue the patch tried to address can be handled differently, which is
what the next patch does.
Signed-off-by: Daniel Mack <zonque@gmail.com> Reported-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Daniel Mack [Mon, 26 May 2014 12:52:39 +0000 (14:52 +0200)]
usb: musb/cppi41: call musb_ep_select() before accessing an endpoint's CSR
Before accessing any of an endpoint's CSR registers, make sure the
correct endpoint is selected. Otherwise, data read from or written to
the registers is likely to affect the wrong endpoint as long as the
connected device has more than one endpoint.
This, of course, leads to all sorts of strange effects such as stream
starvation and driver internal state machine confusion due to spurious
interrupts.
Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Daniel Mack [Mon, 26 May 2014 12:52:38 +0000 (14:52 +0200)]
usb: musb: introduce dma_channel.rx_packet_done
The musb/cppi41 glue layer is capable of handling transactions that span
over more than one USB packet by reloading the DMA descriptors
partially. An urb is considered completed when either its transfer
buffer has been filled entirely (actual_length ==
transfer_buffer_length) or if a packet in the stream has less bytes than
the endpoint's wMaxPacketSize.
Once one of the above conditions is met, musb_dma_completion() is called
from cppi41_trans_done(). However, the final decision whether or not to
return the urb to its owner is made by the core and its determination of
the variable 'done' in musb_host_rx(). This code has currently no way of
knowing what the size of the last packet was, and whether or not to
give back the urb due to a short read.
Fix this by introducing a new boolean flag in 'struct dma_channel', and
set it from musb_cppi41.c. If set, it will make the core do what the
DMA layer decided and complete the urb.
Signed-off-by: Daniel Mack <zonque@gmail.com> Acked-by: George Cherian <george.cherian@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Daniel Mack [Mon, 26 May 2014 12:52:36 +0000 (14:52 +0200)]
usb: musb: use is_host_active() to distinguish between host and gadget mode
On AM33xx platforms, unplugging a device in the middle of an active
transfer leads to a drop of MUSB_DEVCTL_HM in MUSB_DEVCTL before the
system is informed about a disconnect. This consequently makes the musb
core call the gadget code to handle the interrupt request, which then
crashes the kernel because the relevant pointers haven't been set up
for gadget mode.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
in musb_interrupt() and musb_dma_completion() to detect whether the
controller is in host or peripheral mode. This information is provided
by the driver logic and does not rely on register contents.
Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: FunctionFS: Return -ENOENT instead of -ENODEV when device not found.
Syscall mount returns -ENODEV error if requested FS type
has not been found. Returning the same error from FFS mount
callback makes value returned to userspace misleading.
Other file systems returns -ENOENT if requested device
has not been found. Adjust FFS to this convention to make
error codes meaningfull.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Robert Baldyga [Wed, 25 Jun 2014 06:26:49 +0000 (08:26 +0200)]
tools: ffs-aio-example: add license information
Add missing information about license. Some people will probably want to
reuse this code in their projects released under variety of licenses. For this
reason this example is under Public Domain license to avoid GPL limitations.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Robert Baldyga [Wed, 25 Jun 2014 06:26:48 +0000 (08:26 +0200)]
tools: ffs-aio-example: convert to new descriptor format
Since commit [ac8dde11: “Add flags to descriptors block”] functionfs
supports a new descriptor format, so we update example application
to make it using recomended version of descriptors.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for the PLX USB3380 and USB3382.
This driver is based on the driver from the manufacturer.
Since USB338X is register compatible with NET2280, I thought that it
would be better to include this hardware into net2280 driver.
Manufacturer's driver only supported the USB33X, did not follow the
Kernel Style and contain some trivial errors. This patch has tried to
address this issues.
This patch has only been tested on USB338x hardware, but the merge has
been done trying to not affect the behaviour of NET2280.
Tested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Paul Zimmerman [Fri, 23 May 2014 18:39:24 +0000 (11:39 -0700)]
usb: dwc3: add support for USB 2.0-only core configuration
Newer DWC3 controllers can be built for USB 2.0-only mode, where
most of the USB 3.0 circuitry is left out. To support this mode,
the driver must limit the speed programmed into the DCFG register
to Hi-Speed or lower.
Reads and writes to the PIPECTL register are left as-is, since
they should be no-ops in USB 2.0-only mode. Calls to phy_init()
etc. for the USB3 phy are also left as-is, since the no-op USB3
phy should be used for USB 2.0-only mode controllers.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Himangi Saraogi [Sun, 1 Jun 2014 20:43:21 +0000 (02:13 +0530)]
usb: musb: backfin: Introduce the use of the managed version of kzalloc
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, a label is done away with and err2 and err3 renamed.
The following Coccinelle semantic patch was used for making the change:
Himangi Saraogi [Mon, 2 Jun 2014 15:45:05 +0000 (21:15 +0530)]
usb: musb: tusb6010: Introduce the use of the managed version of kzalloc
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, the unnecesary labels are removed and linux/device.h is
added to make sure the devm_*() routine declarations are unambiguously
available.
The following Coccinelle semantic patch was used for making the change:
Himangi Saraogi [Mon, 2 Jun 2014 16:26:01 +0000 (21:56 +0530)]
usb: musb: davinci: use devm_ functions.
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, a label is done away with and clk_get is replaced by it
corresponding devm version and the clk_puts are done away with. The
labels are renamed to make them ordered.
The following Coccinelle semantic patch was used for making the change:
Himangi Saraogi [Tue, 3 Jun 2014 21:19:53 +0000 (02:49 +0530)]
usb: phy: phy-gpio-vbus-usb: use devm_ functions
The various devm_ functions allocate memory that is released when a
driver detaches. This patch uses devm_kzalloc, devm_request_irq,
devm_gpio_request, devm_regulator_get etc. for data that is
allocated in the probe function of a platform device and is only
freed in the remove function. The corresponding free functions are
removed and the labels are done away with.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Felipe Balbi <balbi@ti.com>
Himangi Saraogi [Sat, 14 Jun 2014 15:18:27 +0000 (20:48 +0530)]
usb: gadget: fsl_qe_udc: Introduce use of managed version of kzalloc
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, the unnecesary labels are removed and some labels are
renamed to preserve ordering.
The following Coccinelle semantic patch was used for making the change:
Ben Dooks [Tue, 17 Jun 2014 15:15:01 +0000 (16:15 +0100)]
usb: gadget: r8a66597-udc: remove now unused clean_up and clean_up3 label.
With the devm additions, the clean_up and clean_up3 are now
not needed or used. Change clean_up3 and make everything use
clean_up2 and just remove clean_up.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Felipe Balbi <balbi@ti.com>
Ben Dooks [Tue, 17 Jun 2014 15:14:58 +0000 (16:14 +0100)]
usb: gadget: r8a66597-udc: cleanup error path
With the updates for devm, the cleanup path no longer needs to
check for NULL device state, so remove it and return directly
if the irq resource missing
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Felipe Balbi <balbi@ti.com>
Ben Dooks [Tue, 17 Jun 2014 15:14:56 +0000 (16:14 +0100)]
usb: gadget: r8a66597-udc: use devm_kzalloc() to allocate driver state
Update driver to use devm_kzalloc() to make tracking of resources
easier. Also remove the exit point via cleanup as there's no
cleanup necessary from this point now.
As a note, also removes the error print as the allocation calls
produce errors if they do not return memory.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Felipe Balbi <balbi@ti.com>
Ben Dooks [Tue, 17 Jun 2014 15:14:55 +0000 (16:14 +0100)]
usb: gadget: r8a66597-udc: keep dev as reference to &pdev->dev
Remove usages of &pdev->dev in the driver probe function
with just dev to make the references to it easier to
write. Convert all the current users of it to use it.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Felipe Balbi <balbi@ti.com>
Himangi Saraogi [Fri, 20 Jun 2014 20:40:25 +0000 (02:10 +0530)]
usb: musb: ux500: use devm_ functions
This patch introduces the use of managed interfaces for clk_get and
kzalloc and removes the corresponding free function calls in the probe
and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Felipe Balbi <balbi@ti.com>
Himangi Saraogi [Sun, 22 Jun 2014 07:17:51 +0000 (12:47 +0530)]
usb: gadget: pxa25x_udc: use devm_ functions
This patch introduces the use of devm_request_irq, devm_gpio_request,
devm_clk_get etc. instead of the corresponding unmanaged interfaces. The
calls to the functions like free_irq to free the allocated resources are
removed as they are no longer required. Some labels in the probe function
are also done away with and the name of the label err_gpio_pullup is
changed to make it less specific to the context.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Felipe Balbi <balbi@ti.com>
Linus Torvalds [Sun, 29 Jun 2014 20:40:08 +0000 (13:40 -0700)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Another round of ARM fixes. The largest change here is the L2 changes
to work around problems for the Armada 37x/380 devices, where most of
the size comes down to comments rather than code.
The other significant fix here is for the ptrace code, to ensure that
rewritten syscalls work as intended. This was pointed out by Kees
Cook, but Will Deacon reworked the patch to be more elegant.
The remainder are fairly trivial changes"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
ARM: 8086/1: Set memblock limit for nommu
ARM: 8085/1: sa1100: collie: add top boot mtd partition
ARM: 8084/1: sa1100: collie: revert back to cfi_probe
ARM: 8080/1: mcpm.h: remove unused variable declaration
ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache
Will Deacon [Fri, 27 Jun 2014 16:01:47 +0000 (17:01 +0100)]
ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
On the syscall tracing path, we call out to secure_computing() to allow
seccomp to check the syscall number being attempted. As part of this, a
SIGTRAP may be sent to the tracer and the syscall could be re-written by
a subsequent SET_SYSCALL ptrace request. Unfortunately, this new syscall
is ignored by the current code unless TIF_SYSCALL_TRACE is also set on
the current thread.
This patch slightly reworks the enter path of the syscall tracing code
so that we always reload the syscall number from
current_thread_info()->syscall after the potential ptrace traps.
Acked-by: Kees Cook <keescook@chromium.org> Tested-by: Kees Cook <keescook@chromium.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Laura Abbott [Fri, 27 Jun 2014 09:17:27 +0000 (10:17 +0100)]
ARM: 8086/1: Set memblock limit for nommu
Commit 1c2f87c (ARM: 8025/1: Get rid of meminfo) changed find_limits
to use memblock_get_current_limit for calculating the max_low pfn.
nommu targets never actually set a limit on memblock though which
means memblock_get_current_limit will just return the default
value. Set the memblock_limit to be the end of DDR to make sure
bounds are calculated correctly.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately the detection was challenged on the defective unit used for tests:
one of the NOR chips did not respond to the CFI query.
Moreover that bad device needed extra delays on erase-suspend/resume cycles.
Tested personally on 3 different units and with feedback of two other users.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Thomas Petazzoni [Fri, 13 Jun 2014 09:58:38 +0000 (10:58 +0100)]
ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache
When a PL310 cache is used on a system that provides hardware
coherency, the outer cache sync operation is useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
To avoid this, this commit introduces a new Device Tree property
'arm,io-coherent' for the L2 cache controller node, valid only for the
PL310 cache. It identifies the usage of the PL310 cache in an I/O
coherent configuration. Internally, it makes the driver disable the
outer cache sync operation.
Note that technically speaking, a fully coherent system wouldn't
require any of the other .outer_cache operations. However, in
practice, when booting secondary CPUs, these are not yet coherent, and
therefore a set of cache maintenance operations are necessary at this
point. This explains why we keep the other .outer_cache operations and
only ->sync is disabled.
While in theory any write to a PL310 register could cause the
deadlock, in practice, disabling ->sync is sufficient to workaround
the deadlock, since the other cache maintenance operations are only
used in very specific situations.
Contrary to previous versions of this patch, this new version does not
simply NULL-ify the ->sync member, because the l2c_init_data
structures are now 'const' and therefore cannot be modified, which is
a good thing. Therefore, this patch introduces a separate
l2c_init_data instance, called of_l2c310_coherent_data.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Sat, 28 Jun 2014 18:32:32 +0000 (11:32 -0700)]
Merge tag 'spi-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes, the biggest one being a fix for the newly
added Qualcomm SPI controller driver to make it not use its internal
chip select due to hardware bugs, replacing it with GPIOs"
* tag 'spi-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: qup: Remove chip select function
spi: qup: Fix order of spi_register_master
spi: sh-sci: fix use-after-free in sh_sci_spi_remove()
spi/pxa2xx: fix incorrect SW mode chipselect setting for BayTrail LPSS SPI
Linus Torvalds [Sat, 28 Jun 2014 18:31:58 +0000 (11:31 -0700)]
Merge tag 'regulator-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Several driver specific fixes here, the palmas fixes being especially
important for a range of boards - the recent updates to support new
devices have introduced several regressions"
* tag 'regulator-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps65218: Correct the the config register for LDO1
regulator: tps65218: Add the missing of_node assignment in probe
regulator: palmas: fix typo in enable_reg calculation
regulator: bcm590xx: fix vbus name
regulator: palmas: Fix SMPS enable/disable/is_enabled
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time around. The highlights include:
- iscsi-target CHAP authentication fixes to enforce explicit key
values (Tejas Vaykole + rahul.rane)
- fix a long-standing OOPs in target-core when a alua configfs
attribute is accessed after port symlink has been removed.
(Sebastian Herbszt)
- fix a v3.10.y iscsi-target regression causing the login reject
status class/detail to be ignored (Christoph Vu-Brugier)
- fix a v3.10.y iscsi-target regression to avoid rejecting an
existing ITT during Data-Out when data-direction is wrong (Santosh
Kulkarni + Arshad Hussain)
- fix a iscsi-target related shutdown deadlock on UP kernels (Mikulas
Patocka)
- fix a v3.16-rc1 build issue with vhost-scsi + !CONFIG_NET (MST)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: fix iscsit_del_np deadlock on unload
iovec: move memcpy_from/toiovecend to lib/iovec.c
iscsi-target: Avoid rejecting incorrect ITT for Data-Out
tcm_loop: Fix memory leak in tcm_loop_submission_work error path
iscsi-target: Explicily clear login response PDU in exception path
target: Fix left-over se_lun->lun_sep pointer OOPs
iscsi-target; Enforce 1024 byte maximum for CHAP_C key value
iscsi-target: Convert chap_server_compute_md5 to use kstrtoul
Mikulas Patocka [Mon, 23 Jun 2014 17:42:37 +0000 (13:42 -0400)]
iscsi-target: fix iscsit_del_np deadlock on unload
On uniprocessor preemptible kernel, target core deadlocks on unload. The
following events happen:
* iscsit_del_np is called
* it calls send_sig(SIGINT, np->np_thread, 1);
* the scheduler switches to the np_thread
* the np_thread is woken up, it sees that kthread_should_stop() returns
false, so it doesn't terminate
* the np_thread clears signals with flush_signals(current); and goes back
to sleep in iscsit_accept_np
* the scheduler switches back to iscsit_del_np
* iscsit_del_np calls kthread_stop(np->np_thread);
* the np_thread is waiting in iscsit_accept_np and it doesn't respond to
kthread_stop
The deadlock could be resolved if the administrator sends SIGINT signal to
the np_thread with killall -INT iscsi_np
This patch fixes the problem. Using kthread_should_stop to stop the
np_thread is unreliable, so we test np_thread_state instead. If
np_thread_state equals ISCSI_NP_THREAD_SHUTDOWN, the thread exits.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Linus Torvalds [Sat, 28 Jun 2014 02:00:45 +0000 (19:00 -0700)]
Merge tag 'iommu-fixes-v3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- fix VT-d regression with handling multiple RMRR entries per device
- fix a small race that was left in the mmu_notifier handling in the
AMD IOMMUv2 driver
* tag 'iommu-fixes-v3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix small race between invalidate_range_end/start
iommu/vt-d: fix bug in handling multiple RMRRs for the same PCI device
Linus Torvalds [Sat, 28 Jun 2014 01:43:03 +0000 (18:43 -0700)]
Merge branch 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"A pile of fixes related to the VDSO, EFI and 32-bit badsys handling.
It turns out that removing the section headers from the VDSO breaks
gdb, so this puts back most of them. A very simple typo broke
rt_sigreturn on some versions of glibc, with obviously disastrous
results. The rest is pretty much fixes for the corresponding fallout.
The EFI fixes fixes an arithmetic overflow on 32-bit systems and
quiets some build warnings.
Finally, when invoking an invalid system call number on x86-32, we
bypass a bunch of handling, which can make the audit code oops"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi-pstore: Fix an overflow on 32-bit builds
x86/vdso: Error out in vdso2c if DT_RELA is present
x86/vdso: Move DISABLE_BRANCH_PROFILING into the vdso makefile
x86_32, signal: Fix vdso rt_sigreturn
x86_32, entry: Do syscall exit work on badsys (CVE-2014-4508)
x86/vdso: Create .build-id links for unstripped vdso files
x86/vdso: Remove some redundant in-memory section headers
x86/vdso: Improve the fake section headers
x86/vdso2c: Use better macros for ELF bitness
x86/vdso: Discard the __bug_table section
efi: Fix compiler warnings (unused, const, type)
Linus Torvalds [Sat, 28 Jun 2014 01:37:56 +0000 (18:37 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"This is dominated by a large number of changes necessary for the MIPS
BPF code. code. Aside of that there are
- a fix for the MSC system controller support code.
- a Turbochannel fix.
- a recordmcount fix that's MIPS-specific.
- barrier fixes to smp-cps / pm-cps after unrelated changes elsewhere
in the kernel.
- revert support for MSA registers in the signal frames. The
reverted patch did modify the signal stack frame which of course is
inacceptable.
- fix math-emu build breakage with older compilers.
- some related cleanup.
- fix Lasat build error if CONFIG_CRC32 isn't set to y by the user"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (27 commits)
MIPS: Lasat: Fix build error if CRC32 is not enabled.
TC: Handle device_register() errors.
MIPS: MSC: Prevent out-of-bounds writes to MIPS SC ioremap'd region
MIPS: bpf: Fix stack space allocation for BPF memwords on MIPS64
MIPS: BPF: Use 32 or 64-bit load instruction to load an address to register
MIPS: bpf: Fix PKT_TYPE case for big-endian cores
MIPS: BPF: Prevent kernel fall over for >=32bit shifts
MIPS: bpf: Drop update_on_xread and always initialize the X register
MIPS: bpf: Fix is_range() semantics
MIPS: bpf: Use pr_debug instead of pr_warn for unhandled opcodes
MIPS: bpf: Fix return values for VLAN_TAG_PRESENT case
MIPS: bpf: Use correct mask for VLAN_TAG case
MIPS: bpf: Fix branch conditional for BPF_J{GT/GE} cases
MIPS: bpf: Add SEEN_SKB to flags when looking for the PKT_TYPE
MIPS: bpf: Use 'andi' instead of 'and' for the VLAN cases
MIPS: bpf: Return error code if the offset is a negative number
MIPS: bpf: Use the LO register to get division's quotient
MIPS: mm: uasm: Fix lh micro-assembler instruction
MIPS: uasm: Add SLT uasm instruction
MIPS: uasm: Add s3s1s2 instruction builder
...
Linus Torvalds [Sat, 28 Jun 2014 01:04:22 +0000 (18:04 -0700)]
Merge tag 'stable/for-linus-3.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb
Pull swiotlb bugfix from Konrad Rzeszutek Wilk:
"One bug-fix that had been in tree for quite some time. We had assumed
that the physical address zero was invalid and would fail it. But
that is not true and on some architectures it is not reserved and
valid. This fixes it"
* tag 'stable/for-linus-3.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: don't assume PA 0 is invalid
Linus Torvalds [Sat, 28 Jun 2014 00:21:36 +0000 (17:21 -0700)]
Merge tag 'sound-3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here includes a few patchset for fixing mostly HD-audio issues in
addition to a patch assuring the compress API bytes alignment and a
fix for the die-hard existing race condition at USB-audio
disconnection. The volume looks big in Realtek HD-audio code, but
it's just a translation of the fixup tables, and the actual changes
are rather trivial"
* tag 'sound-3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - restore BCLK M/N values when resuming HSW/BDW display controller
ALSA: usb-audio: Fix races at disconnection and PCM closing
ALSA: hda - Adjust speaker HPF and add LED support for HP Spectre 13
ALSA: hda - Make the pin quirk tables use the SND_HDA_PIN_QUIRK macro
ALSA: hda - Make a SND_HDA_PIN_QUIRK macro
ALSA: hda - Add pin quirk for Dell XPS 15
ALSA: hda - hdmi: call overridden init on resume
ALSA: hda - Fix usage of "model" module parameter
ALSA: compress: fix the struct alignment to 4 bytes
Linus Torvalds [Sat, 28 Jun 2014 00:05:39 +0000 (17:05 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Exynos, i915 and msm fixes and one core fix.
exynos:
hdmi power off and mixer issues
msm:
iommu, build fixes,
i915:
regression races and warning fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
drm/i915: vlv_prepare_pll is only needed in case of non DSI interfaces
drm: fix NULL pointer access by wrong ioctl
drm/exynos: enable vsync interrupt while waiting for vblank
drm/exynos: soft reset mixer before reconfigure after power-on
drm/exynos: allow multiple layer updates per vsync for mixer
drm/i915: Hold the table lock whilst walking the file's idr and counting the objects in debugfs
drm/i915: BDW: Adding Reserved PCI IDs.
drm/i915: Only mark the ctx as initialised after a SET_CONTEXT operation
drm/exynos: stop mixer before gating clocks during poweroff
drm/exynos: set power state variable after enabling clocks and power
drm/exynos: disable unused windows on apply
drm/exynos: Fix de-registration ordering
drm/exynos: change zero to NULL for sparse
drm/exynos: dpi: Fix NULL pointer dereference with legacy bindings
drm/exynos: hdmi: fix power order issue
drm/i915: default to having backlight if VBT not available
drm/i915: cache hw power well enabled state
drm/msm: fix IOMMU cleanup for -EPROBE_DEFER
drm/msm: use PAGE_ALIGNED instead of IS_ALIGNED(PAGE_SIZE)
drm/msm/hdmi: set hdp clock rate before prepare_enable
...
commit 9f977ef7b671f6169eca78bf40f230fe84b7c7e5
vhost-scsi: Include prot_bytes into expected data transfer length
in target-pending makes drivers/vhost/scsi.c call memcpy_fromiovecend().
This function is not available when CONFIG_NET is not enabled.
socket.h already includes uio.h, so no callers need updating.
Reported-by: Randy Dunlap <rdunlap@infradead.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iscsi-target: Avoid rejecting incorrect ITT for Data-Out
This patch changes iscsit_check_dataout_hdr() to dump the incoming
Data-Out payload when the received ITT is not associated with a
WRITE, instead of calling iscsit_reject_cmd() for the non WRITE
ITT descriptor.
This addresses a bug where an initiator sending an Data-Out for
an ITT associated with a READ would end up generating a reject
for the READ, eventually resulting in list corruption.
There is one other possible overrun in the lz4 code as implemented by
Linux at this point in time (which differs from the upstream lz4
codebase, but will get synced at in a future kernel release.) As
pointed out by Don, we also need to check the overflow in the data
itself.
While we are at it, replace the odd error return value with just a
"simple" -1 value as the return value is never used for anything other
than a basic "did this work or not" check.
In generic_id the long int timestamp is multiplied by 100000 and needs
an explicit cast to u64.
Without that the id in the resulting pstore filename is wrong and
userspace may have problems parsing it, but more importantly files in
pstore can never be deleted and may fill the EFI flash (brick device?).
This happens because when generic pstore code wants to delete a file,
it passes the id to the EFI backend which reinterpretes it and a wrong
variable name is attempted to be deleted. There's no error message but
after remounting pstore, deleted files would reappear.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com> Acked-by: David Rientjes <rientjes@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Dave Airlie [Fri, 27 Jun 2014 05:04:06 +0000 (15:04 +1000)]
Merge tag 'drm-intel-fixes-2014-06-26' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Fixes for 3.16-rc2; regressions, races, and warns; Broadwell PCI IDs.
* tag 'drm-intel-fixes-2014-06-26' of git://anongit.freedesktop.org/drm-intel:
drm/i915: vlv_prepare_pll is only needed in case of non DSI interfaces
drm/i915: Hold the table lock whilst walking the file's idr and counting the objects in debugfs
drm/i915: BDW: Adding Reserved PCI IDs.
drm/i915: Only mark the ctx as initialised after a SET_CONTEXT operation
drm/i915: default to having backlight if VBT not available
drm/i915: cache hw power well enabled state
tcm_loop: Fix memory leak in tcm_loop_submission_work error path
This patch fixes a tcm_loop_cmd descriptor memory leak in the
tcm_loop_submission_work() error path, and would result in
warnings about leaked tcm_loop_cmd_cache objects at module
unload time.
Go ahead and invoke kmem_cache_free() to release tl_cmd back to
tcm_loop_cmd_cache before calling sc->scsi_done().
Reported-by: Sebastian Herbszt <herbszt@gmx.de> Tested-by: Sebastian Herbszt <herbszt@gmx.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iscsi-target: Explicily clear login response PDU in exception path
This patch adds a explicit memset to the login response PDU
exception path in iscsit_tx_login_rsp().
This addresses a regression bug introduced in commit baa4d64b
where the initiator would end up not receiving the login
response and associated status class + detail, before closing
the login connection.
This patch fixes a left-over se_lun->lun_sep pointer OOPs when one
of the /sys/kernel/config/target/$FABRIC/$WWPN/$TPGT/lun/$LUN/alua*
attributes is accessed after the $DEVICE symlink has been removed.
To address this bug, go ahead and clear se_lun->lun_sep memory in
core_dev_unexport(), so that the existing checks for show/store
ALUA attributes in target_core_fabric_configfs.c work as expected.
Reported-by: Sebastian Herbszt <herbszt@gmx.de> Tested-by: Sebastian Herbszt <herbszt@gmx.de> Cc: stable@vger.kernel.org Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
projects / karo-tx-linux.git / log