We need to program the rfkill switch GPIO pin direction to input at
device initialization time, not only when the interface is brought up.
Doing this only when the interface is brought up could lead to rfkill
detecting the switch is turned on erroneously and inability to create
the interface and bringing it up.
Reported-and-tested-by: Andreas Messer <andi@bastelmap.de> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo Van Doorn <ivdoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo Van Doorn <ivdoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Maximilian Engelhardt <maxi@daemonizer.de> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo Van Doorn <ivdoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid the construction of a malformed DMA request sent to
the DMA controller.
Log message is for debug only because this condition is unlikely to
append and may only trigger at driver development time.
When call_crda() is called we kick off a witch hunt search
for the same regulatory domain on our internal regulatory
database and that work gets kicked off on a workqueue, this
is done while the cfg80211_mutex is held. If that workqueue
kicks off it will first lock reg_regdb_search_mutex and
later cfg80211_mutex but to ensure two CPUs will not contend
against cfg80211_mutex the right thing to do is to have the
reg_regdb_search() wait until the cfg80211_mutex is let go.
The lockdep report is pasted below.
cfg80211: Calling CRDA to update world regulatory domain
======================================================
[ INFO: possible circular locking dependency detected ]
3.3.8 #3 Tainted: G O
-------------------------------------------------------
kworker/0:1/235 is trying to acquire lock:
(cfg80211_mutex){+.+...}, at: [<816468a4>] set_regdom+0x78c/0x808 [cfg80211]
but task is already holding lock:
(reg_regdb_search_mutex){+.+...}, at: [<81646828>] set_regdom+0x710/0x808 [cfg80211]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Reported-by: Felix Fietkau <nbd@openwrt.org> Tested-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Revision 1.0 Janz CMOD-IO Carrier Board does not have support for
the reset registers. To support older hardware, the code is changed to
use the hardware reset register on the Janz VMOD-ICAN3 hardware itself.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an oops which occurs when unloading the driver, while the
network interface is still up. The problem is that first the io mapping is
teared own, then the CAN device is unregistered, resulting in accessing the
hardware's iomem:
Signed-off-by: Søren Holm <sgh@sgh.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a number of problems that occur for the latest version
of the Realtek RTL8188CE device with the in-kernel driver. These
include selection of the wrong firmware, and system lockup. A full
fix is known, but is too invasive for inclusion in stable. This patch
fixes the problem with loading the wrong firmware, and logs a message
that the device may not work for kernels 3.6 and older.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Anisse Astier <anisse@astier.eu> Cc: Li Chaoming <chaoming_li@realsil.com.cn> Tested-by: Anisse Astier <anisse@astier.eu> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current implementation simply ignores attribute flags. Thus, there is
no notification to userland of unsupported features. Check syscall's
attribute flags to let userland know if a feature is supported by the
kernel. This is also needed to distinguish between future kernels what
might support a feature.
Signed-off-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/20120910093018.GO8285@erda.amd.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
See commit b6999b191 which did the same modification for x86's mm/gup,
Quote from commit b6999b191:
"If compound pages are used and the page is a
tail page, gup_huge_pmd() increases _mapcount to record tail page are
mapped while gup_huge_pud does not do that."
[ralf@linux-mips.org: fixed rejects caused by the original patch getting
linewrapped.]
This patch zeroes the SCTLR.TRE bit prior to setting the mapping as
cacheable for ARMv7 cores in the decompressor, ensuring that the
memory region attributes are obtained from the C and B bits, not from
the page tables.
Cc: Nicolas Pitre <nico@fluxnic.net> Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Matthew Leach <matthew.leach@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kdump can be interrupted by watchdog timer when the timer is left
activated on the crash kernel. Changed the hpwdt driver to disable
watchdog timer at boot-time. This assures that watchdog timer is
disabled until /dev/watchdog is opened, and prevents watchdog timer
to be left running on the crash kernel.
Signed-off-by: Toshi Kani <toshi.kani@hp.com> Tested-by: Lisa Mitchell <lisa.mitchell@hp.com> Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1ad75b9e1628 ("c/r: prctl: add minimal address test to
PR_SET_MM") added some address checking to prctl_set_mm() used by
checkpoint-restore. This causes a build error for no-MMU systems:
kernel/sys.c: In function 'prctl_set_mm':
kernel/sys.c:1868:34: error: 'mmap_min_addr' undeclared (first use in this function)
The test for mmap_min_addr doesn't make a lot of sense for no-MMU code
as noted in commit 6e1415467614 ("NOMMU: Optimise away the
{dac_,}mmap_min_addr tests").
This patch defines mmap_min_addr as 0UL in the no-MMU case so that the
compiler will optimize away tests for "addr < mmap_min_addr".
Signed-off-by: Mark Salter <msalter@redhat.com> Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When new BT USB adapter is plugged in it's configured while still being powered
off (HCI_AUTO_OFF flag is set), thus Set LE will only set dev_flags but won't
write changes to controller. As a result it's not possible to start device
discovery session on LE controller as it uses interleaved discovery which
requires LE Supported Host flag in extended features.
This patch ensures HCI Write LE Host Supported is sent when Set Powered is
called to power on controller and clear HCI_AUTO_OFF flag.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Acked-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For example, when a usb reset is received (I could reproduce it
running something very similar to this[1] in a loop) it could be
that the device is unregistered while the power_off delayed work
is still scheduled to run.
When new BT USB adapter is plugged in it's configured while still being powered
off (HCI_AUTO_OFF flag is set), thus Set SSP will only set dev_flags but won't
write changes to controller. As a result remote devices won't use Secure Simple
Pairing with our device due to SSP Host Support flag disabled in extended
features and may also reject SSP attempt from our side (with possible fallback
to legacy pairing).
This patch ensures HCI Write Simple Pairing Mode is sent when Set Powered is
called to power on controller and clear HCI_AUTO_OFF flag.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Acked-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the commands below to write some data to a virtio-scsi LUN of the
QEMU guest(32-bit) with 1G physical memory(qemu -m 1024), the qemu will crash.
# sudo mkfs.ext4 /dev/sdb (/dev/sdb is the virtio-scsi LUN.)
# sudo mount /dev/sdb /mnt
# dd if=/dev/zero of=/mnt/file bs=1M count=1024
In current implementation, sg_set_buf is called to add buffers to sg list which
is put into the virtqueue eventually. But if there are some HighMem pages in
table->sgl you can not get virtual address by sg_virt. So, sg_virt(sg_elem) may
return NULL value. This will cause QEMU exit when virtqueue_map_sg is called
in QEMU because an invalid GPA is passed by virtqueue.
Two solutions are discussed here:
http://lkml.indiana.edu/hypermail/linux/kernel/1207.3/00675.html
Finally, value assignment approach was adopted because:
Value assignment creates a well-formed scatterlist, because the termination
marker in source sg_list has been set in blk_rq_map_sg(). The last entry of the
source sg_list is just copied to the the last entry in destination list. Note
that, for now, virtio_ring does not care about the form of the scatterlist and
simply processes the first out_num + in_num consecutive elements of the sg[]
array.
I have tested the patch on my workstation. QEMU would not crash any more.
Signed-off-by: Wang Sen <senwang@linux.vnet.ibm.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a command status of CMD_PROTOCOL_ERR is received, this
information should be conveyed to the SCSI mid layer, not
dropped on the floor. CMD_PROTOCOL_ERR may be received
from the Smart Array for any commands destined for an external
RAID controller such as a P2000, or commands destined for tape
drives or CD/DVD-ROM drives, if for instance a cable is
disconnected. This mostly affects multipath configurations, as
disconnecting a cable on a non-multipath configuration is not
going to do anything good regardless of whether CMD_PROTOCOL_ERR
is handled correctly or not. Not handling CMD_PROTOCOL_ERR
correctly in a multipath configaration involving external RAID
controllers may cause data corruption, so this is quite a serious
bug. This bug should not normally cause a problem for direct
attached disk storage.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following kernel panic invoked by uninitialized fields
in the chip initialization for the 1G bnx2 iSCSI offload.
One of the bits in the chip initialization is being used by the latest
firmware to control overflow packets. When this control bit gets enabled
erroneously, it would ultimately result in a bad packet placement which would
cause the bnx2 driver to dereference a NULL ptr in the placement handler.
This can happen under certain stress I/O environment under the Linux
iSCSI offload operation.
This patch checks whether HBA is SAS2008 B0 controller.
if it is a SAS2008 B0 controller then it use IO-APIC interrupt instead of MSIX,
as SAS2008 B0 controller doesn't support MSIX interrupts.
Commit d38bd3aef ("Add -Werror compilation flag") is causing build breakage
with random gcc incarnations. These look like gcc problems, but we shouldn't
break the build because of a bad gcc. Fix this by adding a make flag
WARNINGS_BECOME_ERRORS=1
which is the same as aic7xxx uses so ordinarily the build doesn't use -Werror
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Cc: Alex Iannicelli <alex.iannicelli@emulex.com> Cc: James Smart <james.smart@emulex.com> Cc: Jonathan Nieder <jrnieder@gmail.com> Cc: Mike Pagano <mpagano@gentoo.org> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes a bug found by Nish Aravamudan
(https://lkml.org/lkml/2012/5/15/220) where the driver is not following
the spec (it is not aligning the rx buffer on a 16-byte boundary) and the
hypervisor aborts the registration, making the device unusable.
The fix follows BenH's recommendation (https://lkml.org/lkml/2012/7/20/461)
to replace the kmalloc+map for a single call to dma_alloc_coherent()
because that function always aligns to a 16-byte boundary.
The stable trees will run into this bug whenever the rx buffer kmalloc call
returns something not aligned on a 16-byte boundary.
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspending an open usbnet device results in constant
rescheduling of usbnet_bh.
commit 65841fd5 "usbnet: handle remote wakeup asap"
refactored the usbnet_bh code to allow sharing the
urb allocate and submit code with usbnet_resume. In
this process, a test for, and immediate return on,
ENOLINK from rx_submit was unintentionally dropped.
The rx queue will not grow if rx_submit fails,
making usbnet_bh reschedule itself. This results
in a softirq storm if the error is persistent.
rx_submit translates the usb_submit_urb error
EHOSTUNREACH into ENOLINK, so this is an expected
and persistent error for a suspended device. The
old code tested for this condition and avoided
rescheduling. Putting this test back.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: Ming Lei <ming.lei@canonical.com> Cc: Oliver Neukum <oneukum@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function returns the wrong value, which causes the callers to get
the length of the resulting pathname wrong when it contains non-ASCII
characters.
This seems to fix https://bugzilla.samba.org/show_bug.cgi?id=6767
Reported-by: Baldvin Kovacs <baldvin.kovacs@gmail.com> Reported-and-Tested-by: Nicolas Lefebvre <nico.lefebvre@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue introduced after commit 4ea5454203d991ec
("HID: Fix race condition between driver core and ll-driver").
After that commit, hid-core discards any incoming packet that arrives while
hid driver's probe function is being executed.
This broke the enumeration process of hid-logitech-dj, that must receive
control packets in-band with the mouse and keyboard packets. Discarding mouse
or keyboard data at the very begining is usually fine, but it is not the case
for control packets.
This patch forces a re-enumeration of the paired devices when a packet arrives
that comes from an unknown device.
Based on a patch originally written by Benjamin Tissoires.
The 'name' sysfs attribute is mandatory for hwmon devices, but was missing
in this driver.
Cc: Paul Thomas <pthomas8589@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Jean Delvare <khali@linux-fr.org> Acked-by: Paul Thomas <pthomas8589@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quirk introduced with commit 00250ec90963b7ef6678438888f3244985ecde14 (hwmon: fam15h_power: fix
bogus values with current BIOSes) is not only required during driver
load but also when system resumes from suspend. The BIOS might set the
previously recommended (but unsuitable) initilization value for the
running average range register during resume.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Tested-by: Andreas Hartmann <andihartmann@01019freenet.de> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hypervisor is in charge of allocating the proper "NUMA" memory
and dealing with the CPU scheduler to keep them bound to the proper
NUMA node. The PV guests (and PVHVM) have no inkling of where they
run and do not need to know that right now. In the future we will
need to inject NUMA configuration data (if a guest spans two or more
NUMA nodes) so that the kernel can make the right choices. But those
patches are not yet present.
In the meantime, disable the NUMA capability in the PV guest, which
also fixes a bootup issue. Andre says:
"we see Dom0 crashes due to the kernel detecting the NUMA topology not
by ACPI, but directly from the northbridge (CONFIG_AMD_NUMA).
This will detect the actual NUMA config of the physical machine, but
will crash about the mismatch with Dom0's virtual memory. Variation of
the theme: Dom0 sees what it's not supposed to see.
This happens with the said config option enabled and on a machine where
this scanning is still enabled (K8 and Fam10h, not Bulldozer class)
As the initial domain we are able to search/map certain regions
of memory to harvest configuration data. For all low-level we
use ACPI tables - for interrupts we use exclusively ACPI _PRT
(so DSDT) and MADT for INT_SRC_OVR.
The SMP MP table is not used at all. As a matter of fact we do
not even support machines that only have SMP MP but no ACPI tables.
Lets follow how Moorestown does it and just disable searching
for BIOS SMP tables.
This also fixes an issue on HP Proliant BL680c G5 and DL380 G6:
9f->100 for 1:1 PTE
Freeing 9f-100 pfn range: 97 pages freed
1-1 mapping on 9f->100
.. snip..
e820: BIOS-provided physical RAM map:
Xen: [mem 0x0000000000000000-0x000000000009efff] usable
Xen: [mem 0x000000000009f400-0x00000000000fffff] reserved
Xen: [mem 0x0000000000100000-0x00000000cfd1dfff] usable
.. snip..
Scan for SMP in [mem 0x00000000-0x000003ff]
Scan for SMP in [mem 0x0009fc00-0x0009ffff]
Scan for SMP in [mem 0x000f0000-0x000fffff]
found SMP MP-table at [mem 0x000f4fa0-0x000f4faf] mapped at [ffff8800000f4fa0]
(XEN) mm.c:908:d0 Error getting mfn 100 (pfn 5555555555555555) from L1 entry 0000000000100461 for l1e_owner=0, pg_owner=0
(XEN) mm.c:4995:d0 ptwr_emulate: could not get_page_from_l1e()
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81ac07e2>] xen_set_pte_init+0x66/0x71
. snip..
Pid: 0, comm: swapper Not tainted 3.6.0-rc6upstream-00188-gb6fb969-dirty #2 HP ProLiant BL680c G5
.. snip..
Call Trace:
[<ffffffff81ad31c6>] __early_ioremap+0x18a/0x248
[<ffffffff81624731>] ? printk+0x48/0x4a
[<ffffffff81ad32ac>] early_ioremap+0x13/0x15
[<ffffffff81acc140>] get_mpc_size+0x2f/0x67
[<ffffffff81acc284>] smp_scan_config+0x10c/0x136
[<ffffffff81acc2e4>] default_find_smp_config+0x36/0x5a
[<ffffffff81ac3085>] setup_arch+0x5b3/0xb5b
[<ffffffff81624731>] ? printk+0x48/0x4a
[<ffffffff81abca7f>] start_kernel+0x90/0x390
[<ffffffff81abc356>] x86_64_start_reservations+0x131/0x136
[<ffffffff81abfa83>] xen_start_kernel+0x65f/0x661
(XEN) Domain 0 crashed: 'noreboot' set - not rebooting.
which is that ioremap would end up mapping 0xff using _PAGE_IOMAP
(which is what early_ioremap sticks as a flag) - which meant
we would get MFN 0xFF (pte ff461, which is OK), and then it would
also map 0x100 (b/c ioremap tries to get page aligned request, and
it was trying to map 0xf4fa0 + PAGE_SIZE - so it mapped the next page)
as _PAGE_IOMAP. Since 0x100 is actually a RAM page, and the _PAGE_IOMAP
bypasses the P2M lookup we would happily set the PTE to 1000461.
Xen would deny the request since we do not have access to the
Machine Frame Number (MFN) of 0x100. The P2M[0x100] is for example
0x80140.
Fixes-Oracle-Bugzilla: https://bugzilla.oracle.com/bugzilla/show_bug.cgi?id=13665 Acked-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the caller passes a valid kmap_op to m2p_add_override, we use
kmap_op->dev_bus_addr to store the original mfn, but dev_bus_addr is
part of the interface with Xen and if we are batching the hypercalls it
might not have been written by the hypervisor yet. That means that later
on Xen will write to it and we'll think that the original mfn is
actually what Xen has written to it.
Rather than "stealing" struct members from kmap_op, keep using
page->index to store the original mfn and add another parameter to
m2p_remove_override to get the corresponding kmap_op instead.
It is now responsibility of the caller to keep track of which kmap_op
corresponds to a particular page in the m2p_override (gntdev, the only
user of this interface that passes a valid kmap_op, is already doing that).
There may be a bug when registering section info. For example, on my
Itanium platform, the pfn range of node0 includes the other nodes, so
other nodes' section info will be double registered, and memmap's page
count will equal to 3.
Because MIN_MEMORY_BLOCK_SIZE is int type and length of 32bits,
so MIN_MEMORY_BLOCK_SIZE(1 << 32) will will equal to 0.
Actually when SECTION_SIZE_BITS >= 31, MIN_MEMORY_BLOCK_SIZE will be wrong.
This will cause wrong system memory infomation in sysfs.
I think it should be:
And "echo offline > memory0/state" will cause following call trace:
kernel BUG at mm/memory_hotplug.c:885!
sh[6455]: bugcheck! 0 [1]
Pid: 6455, CPU 0, comm: sh
psr : 0000101008526030 ifs : 8000000000000fa4 ip : [<a0000001008c40f0>] Not tainted (3.6.0-rc1)
ip is at offline_pages+0x210/0xee0
Call Trace:
show_stack+0x80/0xa0
show_regs+0x640/0x920
die+0x190/0x2c0
die_if_kernel+0x50/0x80
ia64_bad_break+0x3d0/0x6e0
ia64_native_leave_kernel+0x0/0x270
offline_pages+0x210/0xee0
alloc_pages_current+0x180/0x2a0
Signed-off-by: Jianguo Wu <wujianguo@huawei.com> Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Cc: "Luck, Tony" <tony.luck@intel.com> Reviewed-by: Michal Hocko <mhocko@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MCP2515 has a silicon bug causing repeated frame transmission, see section
5 of MCP2515 Rev. B Silicon Errata Revision G (March 2007).
Basically, setting TXBnCTRL.TXREQ in either SPI mode (00 or 11) will eventually
cause the bug. The workaround proposed by Microchip is to use mode 00 and send
a RTS command on the SPI bus to initiate the transmission.
It is a bad idea to hold a spinlock and call flush_work_sync.
Move the workqueue cleanup outside the spinlock and use cancel_work_sync,
on closing the channel this seems to be the more correct function.
Remove the never used and constant return value of mISDN_freebchannel.
Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses be16_to_cpu and cpu_to_be16 to convert data in SMBus word
operations from chip to host byte order. However, the data passed from and to
the SMBus word API functions is in host byte order, not in chip byte order.
Conversion should therefore use swab16 instead of be16 to change the byte order.
Replace driver internal word conversion functions with SMBus API functions to
solve the problem.
On some platforms, bootloaders are known to do some interesting RTC
programming. Without going into the obscurities as to why this may be
the case, suffice it to say the the driver should not make any
assumptions about the state of the RTC when the driver loads. In
particular, the driver probe should be sure that all interrupts are
disabled until otherwise programmed.
This was discovered when finding bursty I2C traffic every second on
Overo platforms. This I2C overhead was keeping the SoC from hitting
deep power states. The cause was found to be the RTC firing every
second on the I2C-connected TWL PMIC.
Special thanks to Felipe Balbi for suggesting to look for a rogue driver
as the source of the I2C traffic rather than the I2C driver itself.
Special thanks to Steve Sakoman for helping track down the source of the
continuous RTC interrups on the Overo boards.
Signed-off-by: Kevin Hilman <khilman@ti.com> Cc: Felipe Balbi <balbi@ti.com> Tested-by: Steve Sakoman <steve@sakoman.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Tested-by: Shubhrajyoti Datta <omaplinuxkernel@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The heuristic method for buddy has been introduced since commit 43506fad21ca ("mm/page_alloc.c: simplify calculation of combined index
of adjacent buddy lists"). But the page address of higher page's buddy
was wrongly calculated, which will lead page_is_buddy to fail for ever.
IOW, the heuristic method would be disabled with the wrong page address
of higher page's buddy.
Calculating the page address of higher page's buddy should be based
higher_page with the offset between index of higher page and index of
higher page's buddy.
Signed-off-by: Haifeng Li <omycle@gmail.com> Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Reviewed-by: Michal Hocko <mhocko@suse.cz> Cc: KyongHo Cho <pullip.cho@samsung.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Minchan Kim <minchan.kim@gmail.com> Cc: Johannes Weiner <jweiner@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pause and resume operations indicate that the stream can be
un-paused/resumed from the exact location they were paused/suspended.
This is not true for this driver, the pause and suspend triggers share
the same code path with stop, they flush all pending DMA transfers.
This drops all pending samples. The pause_release/resume triggers are
the same as start, except that prepare won't be called beforehand,
nothing will be enqueued to the DMA engine and nothing will happen (no
audio). Removing the pause flag will let apps know that it isn't
supported. Removing the resume flag will cause user space to call
prepare and start instead of resume, so audio will continue playing when
the system wakes up.
Before removing the pause and resume flags, I tested this on an exynos
5250, using 'aplay -i'. Pause/un-pause leads to silence followed by a
write error. Suspend/resume testing led to the same result. Removing
the two flags fixes suspend/resume (since snd_pcm_prepare is called
again). And leads to a proper reporting of pause not supported.
Signed-off-by: Dylan Reid <dgreid@chromium.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a serious but uncommon bug in nbd which occurs when there is heavy
I/O going to the nbd device while, at the same time, a failure (server,
network) or manual disconnect of the nbd connection occurs.
There is a small window between the time that the nbd_thread is stopped
and the socket is shutdown where requests can continue to be queued to
nbd's internal waiting_queue. When this happens, those requests are
never completed or freed.
The fix is to clear the waiting_queue on shutdown of the nbd device, in
the same way that the nbd request queue (queue_head) is already being
cleared.
Signed-off-by: Paul Clements <paul.clements@steeleye.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a replacement device becomes active, we mark the device that it
replaces as 'faulty' so that it can subsequently get removed.
However 'calc_degraded' only pays attention to the primary device, not
the replacement, so the array appears to become degraded, which is
wrong.
So teach 'calc_degraded' to consider any replacement if a primary
device is faulty.
This is suitable for -stable as an incorrect 'degraded' value can
confuse md and could lead to data corruption.
This is only relevant for 3.3 and later.
Reported-by: Robin Hill <robin@robinhill.me.uk> Reported-by: John Drescher <drescherjm@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It isn't always necessary to update the metadata when spares are
removed as the presence-or-not of a spare isn't really important to
the integrity of an array.
Also activating a spare doesn't always require updating the metadata
as the update on 'recovery-completed' is usually sufficient.
However the introduction of 'replacement' devices have made these
transitions sometimes more important. For example the 'Replacement'
flag isn't cleared until the original device is removed, so we need
to ensure a metadata update after that 'spare' is removed.
So set MD_CHANGE_DEVS whenever a spare is activated or removed, to
complement the current situation where it is set when a spare is added
or a device is failed (or a number of other less common situations).
This is suitable for -stable as out-of-data metadata could lead
to data corruption.
This is only relevant for 3.3 and later 9when 'replacement' as
introduced.
A 'struct r10bio' has an array of per-copy information at the end.
This array is declared with size [0] and r10bio_pool_alloc allocates
enough extra space to store the per-copy information depending on the
number of copies needed.
So declaring a 'struct r10bio on the stack isn't going to work. It
won't allocate enough space, and memory corruption will ensue.
So in the two places where this is done, declare a sufficiently large
structure and use that instead.
The two call-sites of this bug were introduced in 3.4 and 3.5
so this is suitable for both those kernels. The patch will have to
be modified for 3.4 as it only has one bug.
Reported-by: Ivan Vasilyev <ivan.vasilyev@gmail.com> Tested-by: Ivan Vasilyev <ivan.vasilyev@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
changed 0.90 metadata handling to truncated size to 4TB as that is
all that 0.90 can record.
However for RAID0 and Linear, 0.90 doesn't need to record the size, so
this truncation is not needed and causes working arrays to become too small.
So avoid the truncation for RAID0 and Linear
This bug was introduced in 3.1 and is suitable for any stable kernels
from then onwards.
As the offending commit was tagged for 'stable', any stable kernel
that it was applied to should also get this patch. That includes
at least 2.6.32, 2.6.33 and 3.0. (Thanks to Ben Hutchings for
providing that list).
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When pkcs_1_v1_5_decode_emsa() returns without error and hash sizes do
not match, hash comparision is not done and digsig_verify_rsa() returns
no error. This is a bug and this patch fixes it.
The bug was introduced in v3.3 by commit b35e286a640f ("lib/digsig:
pkcs_1_v1_5_decode_emsa cleanup").
The following build error occurred during an alpha build:
net/core/sock.c:274:36: error: initializer element is not constant
Dave Anglin says:
> Here is the line in sock.i:
>
> struct static_key memalloc_socks = ((struct static_key) { .enabled =
> ((atomic_t) { (0) }) });
The above line contains two compound literals. It also uses a designated
initializer to initialize the field enabled. A compound literal is not a
constant expression.
The location of the above statement isn't fully clear, but if a compound
literal occurs outside the body of a function, the initializer list must
consist of constant expressions.
> After the __devinit* removal series, I can still get kernel panic in
> show_uevent(). So there are more sources of bug..
>
> Debug patch:
>
> @@ -343,8 +343,11 @@ static ssize_t show_uevent(struct device
> goto out;
>
> /* copy keys to file */
> - for (i = 0; i < env->envp_idx; i++)
> + dev_err(dev, "uevent %d env[%d]: %s/.../%s\n", env->buflen, env->envp_idx, top_kobj->name, dev->kobj.name);
> + for (i = 0; i < env->envp_idx; i++) {
> + printk(KERN_ERR "uevent %d env[%d]: %s\n", (int)count, i, env->envp[i]);
> count += sprintf(&buf[count], "%s\n", env->envp[i]);
> + }
>
> Oops message, the env[] is again not properly initilized:
>
> [ 44.068623] input input0: uevent 61 env[805306368]: input0/.../input0
> [ 44.069552] uevent 0 env[0]: (null)
This is a completely different CONFIG_HOTPLUG problem, only
demonstrating another reason why CONFIG_HOTPLUG should go away. I had a
hard time trying to disable it anyway ;-)
The problem this time is lots of code assuming that a call to
add_uevent_var() will guarantee that env->buflen > 0. This is not true
if CONFIG_HOTPLUG is unset. So things like this end up overwriting
env->envp_idx because the array index is -1:
if (add_uevent_var(env, "MODALIAS="))
return -ENOMEM;
len = input_print_modalias(&env->buf[env->buflen - 1],
sizeof(env->buf) - env->buflen,
dev, 0);
Don't know what the best action is, given that there seem to be a *lot*
of this around the kernel. This patch "fixes" the problem for me, but I
don't know if it can be considered an appropriate fix.
[ It is the correct fix for now, for 3.7 forcing CONFIG_HOTPLUG to
always be on is the longterm fix, but it's too late for 3.6 and older
kernels to resolve this that way - gregkh ]
Earlier we used to check for ep->ep.desc to figure out if this ep has
already been enabled and if so, abort.
Ido Shayevitz removed the usb_endpoint_descriptor from private udc
structure 5a6506f00 ("usb: gadget: Update at91_udc to use
usb_endpoint_descriptor inside the struct usb_ep") but did not fix up
the ep_enable condition because _now_ the member is always true and we
can't check if this ep is enabled twice.
Cc: Ido Shayevitz <idos@codeaurora.org> Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com> Tested-by: Mario Isidoro <Mario.Isidoro@tecmic.pt> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was converted to the new start/stop interface in f3d8bf34c2
("usb: gadget: at91_udc: convert to new style start/stop interface").
I overlooked that the driver is overwritting the private data which is
used by the composite framework. The udc driver doesn't read it, it is
only written here.
Tested-by: Fabio Porcedda <fabio.porcedda@gmail.com> Tested-by: Mario Isidoro <Mario.Isidoro@tecmic.pt> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without a reply for USB_DT_BOS the USB3 mode does not work since 448b6eb1 ("USB: Make sure to fetch the BOS desc for roothubs.).
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If USB2 host controller probes fine but USB3 does not then we don't
remove the USB controller properly and lock up the system while the HUB
code will try to enumerate the USB2 controller and access memory which
is no longer available in case the dummy_hcd was compiled as a module.
This is a problem since 448b6eb1 ("USB: Make sure to fetch the BOS desc
for roothubs.) if used in USB3 mode because dummy does not provide this
descriptor and explodes later.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add function to physicaly enable or disable of pullup connection on the USB-D+
line. The uvc gaget will fail, if this function is not implemented.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If oprofilefs_ulong_from_user() is called with count equals zero, *val
remains unchanged. Depending on the implementation it might be
uninitialized. Fixing users of oprofilefs_ulong_ from_user().
We missed these s390 changes with:
913050b oprofile: Fix uninitialized memory access when writing to writing to oprofilefs
Signed-off-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For several MoviNAND eMMC parts, there are known issues with secure
erase and secure trim. For these specific MoviNAND devices, we skip
these operations.
Specifically, there is a bug in the eMMC firmware that causes
unrecoverable corruption when the MMC is erased with MMC_CAP_ERASE
enabled.
Even if the datasheet says that the not busy flag has to be used only
for write operations, it's false except for version lesser than v2xx.
Not waiting on the not busy flag for read operations can cause the
controller to hang-up during the initialization of some SD cards
with DMA after the first CMD6 -- the next command is sent too early.
Since commit 30832ab56 ("mmc: sdhci: Always pass clock request value
zero to set_clock host op") was merged, esdhc_set_clock starts hitting
"if (clock == 0)" where ESDHC_SYSTEM_CONTROL has been operated. This
causes SDHCI card-detection function being broken. Fix the regression
by moving "if (clock == 0)" above ESDHC_SYSTEM_CONTROL operation.
commit a606dac368eed5696fb38e16b1394f1d049c09e9 adds support to link
devices which have _PRx, if a device does not have _PRx, a warning
message will be printed.
This commit is for ZPODD on Intel ZPODD capable platforms, on other
platforms, it has no problem if there is no power resource for this
device, so a warning here is not appropriate, change it to debug.
Reported-by: Borislav Petkov <bp@amd64.org> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0090def("ACPI: Add interface to register/unregister device
to/from power resources") used resource_lock to protect the devices list
that relies on power resource. It caused a mutex dead lock, as below
This patch adds a new mutex "devices_lock" to protect the devices list
and calls acpi_power_on_device in acpi_power_on, instead of
__acpi_power_on, after the resource_lock is released.
[rjw: Changed data type of a boolean variable to bool.]
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that there are ACPI BIOSes defining device objects with
_PSx and without either _PSC or _PRx. For devices corresponding to
those ACPI objetcs __acpi_bus_get_power() returns ACPI_STATE_UNKNOWN
and their initial power states are regarded as unknown as a result.
If such a device is a parent of another power-manageable device, the
child cannot be put into a low-power state through ACPI, because
__acpi_bus_set_power() refuses to change power states of devices
whose parents' power states are unknown.
To work around this problem, observe that the ACPI power state of
a device cannot be higher-power (lower-number) than the power state
of its parent. Thus, if the device's _PSC method or the
configuration of its power resources indicates that the device is
in D0, the device's parent has to be in D0 as well. Consequently,
if the parent's power state is unknown when we've just learned that
its child's power state is D0, we can safely set the parent's
power.state field to ACPI_STATE_D0.
Tested-by: Aaron Lu <aaron.lu@intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't mess with file refcounts (or keep a reference to file, for
that matter) in perf_event. Use explicit refcount of its own
instead. Deal with the race between the final reference to event
going away and new children getting created for it by use of
atomic_long_inc_not_zero() in inherit_event(); just have the
latter free what it had allocated and return NULL, that works
out just fine (children of siblings of something doomed are
created as singletons, same as if the child of leader had been
created and immediately killed).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/20120820135925.GG23464@ZenIV.linux.org.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both the schematics and practical testing show that the HP detect GPIO
is high when the headphones are plugged in. Hence, the snd_soc_jack_gpio
should not specify to invert the signal.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Andrey Danin <danindrey@mail.ru> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The unregister_sysctl_table() function hangs if all references to its
ctl_table_header structure are not dropped.
This can happen sometimes because of a leak in proc_sys_lookup():
proc_sys_lookup() gets a reference to the table via lookup_entry(), but
it does not release it when a subsequent call to sysctl_follow_link()
fails.
This patch fixes this leak by making sure the reference is always
dropped on return.
See also commit 076c3eed2c31 ("sysctl: Rewrite proc_sys_lookup
introducing find_entry and lookup_entry") which reorganized this code in
3.4.
added a device specific entry assuming that the device would use
class/subclass/proto == ff/ff/ff like other ZTE devices. It
turns out that ZTE has started using vendor specific subclass
and protocol codes:
We do not have any information on how ZTE intend to use these
codes, but let us assume for now that the 3 sets matching
serial functions in the K5006-Z always will identify a serial
function in a ZTE device.
The element of `das08_boards[]` for the 'das08jr-16-ao' board has the
`ai_encoding` member set to `das08_encode12`. It should be set to
`das08_encode16` same as the 'das08jr/16' board. After all, this board
has 16-bit AI resolution.
The description of the A/D LSB register at offset 0 seems incorrect in
the user manual "cio-das08jr-16-ao.pdf" as it implies that the AI
resolution is only 12 bits. The diagrams of the A/D LSB and MSB
registers show 15 data bits and a sign bit, which matches what the
software expects for the `das08_encode16` AI encoding method.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't zero out bits 15..12 of the data value in `das08jr_ao_winsn()` as
that knobbles the upper three-quarters of the output range for the
'das08jr-16-ao' board.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When attaching a PCI device manually via the comedi driver `attach` hook
(`pci224_attach()`) (called by the comedi core for the
`COMEDI_DEVCONFIG` ioctl), its reference count is incremented in the
`for_each_pci_dev` loop (in `pci224_find_pci_dev()`). It is decremented
when the `detach` hook (`pci224_detach()`) is called to detach the
device. However, when the PCI device is attached automatically via the
`attach_pci` hook (`pci224_attach_pci()`, called at probe time via
`comedi_pci_auto_config()`) it's reference count is not incremented so
there will be an unmatched decrement when detaching the device.
Increment the PCI device reference count in `pci224_attach_pci()` to
correct the mismatch.
Once support for manual configuration has been removed from this driver,
the calls to `pci_dev_get()` and `pci_dev_put()` can be removed.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Dave Jones <davej@redhat.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a race condition that results in memory
corruption when using cleancache.
The race exists between the zcache shrinker handler,
shrink_zcache_memory() and cleancache_get_page().
In most cases, the shrinker will both evict a zbpg
from its buddy list and flush it from tmem before a
cleancache_get_page() occurs on that page. A subsequent
cleancache_get_page() will fail in the tmem layer.
In the rare case that two occur together and the
cleancache_get_page() path gets through the tmem
layer before the shrinker path can flush tmem,
zbud_decompress() does a check to see if the zbpg is a
"zombie", i.e. not on a buddy list, which means the shrinker
is in the process of reclaiming it. If the zbpg is a zombie,
zbud_decompress() returns -EINVAL.
However, this return code is being ignored by the caller,
zcache_pampd_get_data_and_free(), which results in the
caller of cleancache_get_page() thinking that the page has
been properly retrieved when it has not.
This patch modifies zcache_pampd_get_data_and_free() to
convey the failure up the stack so that the caller of
cleancache_get_page() knows the page retrieval failed.
This needs to be applied to stable trees as well.
zcache-main.c was named zcache.c before v3.1, so
I'm not sure how you want to handle trees earlier
than that.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On recent kernels, Realtek codec parser tries to optimize the routing
aggressively and take the headphone output as primary at first. This
caused a regression on VAIO Z with ALC889, the silent output from the
speaker.
The problem seems that the speaker pin must be connected to the first
DAC (0x02) on this machine by some reason although the codec itself
advertises the flexible routing with any DACs.
This patch adds a fix-up for choosing the speaker pin as the primary
so that the right DAC is assigned on this device.
The AK4396 DAC has a linear-scale attentuator, but
sound/pci/ice1712/prodigy_hifi.c used a log scale instead, which is
not quite right. This patch restores the correct scale, borrowing
from the ak4396 code in sound/pci/oxygen/oxygen.c.
snd_hda_codec_reset() calls restore_pincfgs() where the codec is
powered up again, which eventually tries to resume and initialize via
the callbacks of the codec. However, it's the place just after codec
free callback, thus no codec callbacks should be called after that.
On a codec like CS4206, it results in Oops due to the access in init
callback.
This patch fixes the issue by clearing the codec callbacks properly
after freeing codec.
The recent fix for the missing fine delayed time adjustment gives
strange error messages at each start of the playback stream, such as
delay: estimated 0, actual 352
delay: estimated 353, actual 705
These come from the sanity check in retire_playback_urb(). Before the
stream is activated via start_endpoints(), a few silent packets have
been already sent. And at this point the delay account is still in
the state as if the new packets are just queued, so the driver gets
confused and spews the bogus error messages.
For fixing the issue, we just need to check whether the received
packet is valid, whether it's zero sized or not.
With the commit [2faa3bf: ALSA: hda - Rewrite the mute-LED hook with
vmaster hook in patch_sigmatel.c], the former Master volume control
was converted to PCM. This was supposed to be covered by the vmaster
control. But due to the lack of "PCM" slave definition, this didn't
happen properly. The patch fixes the missing entry.
This is caused by the 'reserved' entries which we insert (see 19b52abe3c5d7 - ARM: 7438/1: fill possible PMD empty section gaps)
which get matched for physical address zero.
Resolve this by marking these reserved entries with a different flag.
Tested-by: Murali Nalajala <mnalajal@codeaurora.org> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, omap2_sync32k_clocksource_init() function initializes the 32K
timer as the system clock source regardless of the CONFIG_OMAP_32K_TIMER
setting.
Fix this by providing a default implementation for
!CONFIG_OMAP_32K_TIMER case.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Paul Walmsley <paul@pwsan.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log