ALSA: hda - Resurrect input-source mixer of ALC268 model=acer
In the commit fdbc66266c21976027938642f60e0f047149a61a, I mistakenly
replaced the capture mixer array for ALC268_ACER to nosrc version
although this should be kept to alt_mixer. Now fixed back.
ALSA: hda - CD-audio sound for hda-intel conexant benq laptop
After puting a cd-audio inside my laptop there was no sound out here,
so I decided to install alsa-driver with debug level and setup a
model=test, it didn't help, but then I look at source code and added
this few lines, now cd-audio is working both when playback/recording.
[Additional minor fixes of mixer element/item names by tiwai]
The headphone and speaker mixer elements aren't properly set for
MSI GX620 with targa-8ch-dig quirk.
Also fixed the speaker volume control for other ALC883-targa quirks,
too.
Remove unnecessary (and buggy) init sequences left for IDT92HD83*
codecs in the previous fixes. The DACs are now dynamically connected,
thus shouldn't be set statically in init verbs. Also, the mono_nid
is detected dynamically, thus shouldn't be set staticaly, too.
Add the quirk entry for HP dv6. Also add a workaround for the headphone
detection by setting hp_detect=1 beforehand. Without this, the driver
won't do auto-muting because BIOS doesn't give any HP pin but only a
line-out pin.
ALSA: hda - Fix HP/line-out initialization with IDT/STAC codecs
It's possible that hp_detect is set even though no headphone pin is
detected. The driver issues, however, an unsol event only to hp_pins[0],
which can be invalid.
This patch adds the check of the valid pin to send an unsol event
at initialization and resume callbacks.
IDT92HD73xx and STAC927x codecs use GPIO0 bit as EAPD on many machines.
However, currently we don't set it unless the model is specified just
for safety reason. But, most machines do need this bit, so this safety
handling is rather annoying.
This patch enables GPIO0 setup as default for them. Many HP / Dell
laptops should work even without model override with this change.
ALSA: hda - Use auto model for HP laptops with ALC268 codec
The HP laptops with ALC268 codec seem working better with model=auto
than model=toshiba; e.g. the auto model fixes missing digital outputs.
Let's fix quirk entry to choose auto model explicitly.
Added the quirk for Alienware M17x with IDT 92HD73* codec chip.
It has two HP and one line-out jack, one mic jack, a built-in
speaker and a built-in mic.
Fix the headphone pin routing of ALC268/ALC269 codecs. Using alc882
routine doesn't work because alc268/alc269 parser assumes the
independent DACs for both HP and speaker outputs. Need to assign the
DAC depending on the pin.
Takashi Iwai [Mon, 31 Aug 2009 06:15:26 +0000 (08:15 +0200)]
ALSA: hda - Fix MacBookPro 3,1/4,1 quirk with ALC889A
This patch fixes the wrong headphone output routing for MacBookPro 3,1/4,1
quirk with ALC889A codec, which caused the silent headphone output.
Also, this gives the individual Headphone and Speaker volume controls.
Takashi Iwai [Mon, 31 Aug 2009 06:12:29 +0000 (08:12 +0200)]
ALSA: hda - Add missing mux check for VT1708
In patch_vt1708(), the check of MUX nids is missing and this results in
the -EINVAL error in accessing Input Source mixer element. Simpliy
adding the call of get_mux_nids() fixes the problem.
Takashi Iwai [Fri, 28 Aug 2009 22:49:36 +0000 (00:49 +0200)]
ALSA: hda - Create "Digital Mic Capture Volume" correctly for IDT codecs
So far, the digital mic capture volume wasn't created. This is because
IDT codecs have output amps for digital mics, not input amps, while
input amps should be used for other analog pins. Thus the automatic
capture volume creation should check both directions for digital mics.
Denis Kuplyakov [Tue, 25 Aug 2009 16:15:59 +0000 (18:15 +0200)]
ALSA: hda - Add full audio support on Acer Aspire 7730G notebook
1) Added support of internal subwoofer (it sounds!!!)
2) Auto muting front speakers and internal subwoofer on headphones plug.
3) Internal mic works.
4) 3 channel mods (jack maps):
black pink blue
2ch: front ext mic line in
4ch: front ext mic surround
6ch: front CLFE surround
Can be changed in mixer.
5) Sound can be recorded from:
Internal mic
Ext mic
Cd
Line in
6) 2 separate capture channels.
Takashi Iwai [Tue, 25 Aug 2009 14:12:15 +0000 (16:12 +0200)]
ALSA: hda - Improve auto-cfg mixer name for ALC861-VD
One more patch to give a better name for the primary output controls,
this time for ALC861-VD codec. The change is simple, just checking the
pin connection whether it's a speaker-out. When both speaker and HP
are assigned, we name the volume as "PCM" as this influences on both
outputs.
Takashi Iwai [Tue, 25 Aug 2009 14:08:47 +0000 (16:08 +0200)]
ALSA: hda - Improve auto-cfg mixer name for ALC262
Similar improvements for ALC262 codec like previous two commits:
assign a better name, either Master or Speaker, for the primary output
controls.
However, in the case of ALC262 codec, the necessary changes are larger
than others because we need to check the possibility of different mixer
amps depending on the pins. The pin 0x16 is mono, and bound with the
dedicated mixer 0x0e while other pins are bound with 0x0c. Thus, there
are two possible volumes.
When only one of them is used, we can name it as "Master". OTOH, when
both are used at the same time, they have to be named uniquely.
Takashi Iwai [Tue, 25 Aug 2009 11:10:18 +0000 (13:10 +0200)]
ALSA: hda - Generalize input pin parsing in patch_realtek.c
Provide a standard parser for input pins to create the input mixer
and input source controls instead of having a difference one for each
Realtek codec. The new helper parses the codec connections dynamically
isntead of fixed indicies.
Takashi Iwai [Mon, 24 Aug 2009 12:10:30 +0000 (14:10 +0200)]
ALSA: hda - Reuse ALC268 parser for ALC269
Reuse a part of the code of ALC268 parser for ALC269.
This will change the default output volume either to Front or Speaker
depending on the pin configuration.
Takashi Iwai [Wed, 19 Aug 2009 18:05:02 +0000 (20:05 +0200)]
ALSA: hda - Fix probe of Toshiba laptops with ALC268 codec
There are many variants of Toshiba laptops with ALC268 codec, and
it seems that a few of them don't work with model=toshiba preset
since they have the secondary ALC268 codec just for HDMI output.
This is a regression due to the previous clean-up work to merge all
Toshiba quirk entries into a single check.
This patch adds the identification of such laptops to apply the
standard BIOS-probing method. Unfortunately, Toshiba laptops have
all the same PCI SSID, so we need to check the codec SSID to identify
each device.
Wu Fengguang [Wed, 19 Aug 2009 08:58:59 +0000 (16:58 +0800)]
ALSA: hda: enable speaker output for Compaq 6530s/6531s
HP Compaq 6530s and 6531s internal speaker is silence or becomes silence
within 1 minute after fresh boot. It is found that pin 0x1c must be set to
PIN_OUT mode to make the speaker work. This is weird - line-in pin 0x1c and
speaker pin 0x16 seem to be unrelated.
The codec differences before/after patch are:
@@ Node 0x17 [Pin Complex] wcaps 0x40020b:
Pin Default 0x41a6e130: [N/A] Mic at Ext Rear
Conn = Digital, Color = White
DefAssociation = 0x3, Sequence = 0x0
Misc = NO_PRESENCE
- Pin-ctls: 0x24: IN
+ Pin-ctls: 0x40: OUT
@@ Node 0x1c [Pin Complex] wcaps 0x40018d:
Pin Default 0x41813021: [N/A] Line In at Ext Rear
Conn = 1/8, Color = Blue
DefAssociation = 0x2, Sequence = 0x1
- Pin-ctls: 0x24: IN VREF_80
+ Pin-ctls: 0x40: OUT VREF_HIZ
Unsolicited: tag=00, enabled=0
Connection: 1
0x24
Tests show that it won't impact (external) Mic recording.
Takashi Iwai [Tue, 18 Aug 2009 22:18:10 +0000 (00:18 +0200)]
ALSA: hda - Fix invalid capture mixers with some ALC268 models
The auto-mic clean-up patches caused regressions on some ALC268 models
that have no proper input_mux but with "Input Source" mixer elements.
Such a combination results in Oops when accessed.
[A reason why set_capture_mixer() isn't used in patch_alc268() is that
ALC268 codec have HDA_OUTPUT direction for capture volumes unlike other
codecs. Thus it needs own definitions of capture elements.]
This patch fixes the issues:
- Add a capture mixer definition without input-source
- Use the new capture mixer appropriately
Takashi Iwai [Thu, 13 Aug 2009 16:14:42 +0000 (18:14 +0200)]
ALSA: hda - Fix / clean up IDT92HD83xxx codec parser
A few improvements for IDT 92HD83xxx codec pareser:
- Remove unused / deprecated mixer-amp controls
- Handle d-mics as normal inputs since this codec has no separate
MUXes for analog and digital
- Don't create duplicated controls for capture volumes with Mux
capture volumes
Takashi Iwai [Thu, 13 Aug 2009 06:23:24 +0000 (08:23 +0200)]
ALSA: hda - Enable line-out detection only with speakers
Enable line-out detection for IDT/STAC codecs only when speaker pins
exist. In some cases, the speaker itself is identified as line-out,
and this confuses the situation. Only the extra line-outs should do
auto-muting.
ALSA: hda - fix noise issue when recording from digital mic with alc268
With auto config model of alc268 realtek codec, it allows to select any
of possible available digital microphone inputs when only one is
available. For example, when only digital mic in nid 0x12 is available,
on second input source it will allow you to select unavailable digital
mic in nid 0x13. The problem is that selecting unavailable digital mic
creates a source of noise when recording (I'm not sure if this happens
on all machines with alc268 and only one digital mic input, but testing
on a quanta uw1 netbook a lot of noise is introduced in recording from
digital mic 0x12/first input source, when you select the unavailable
digital mic 0x13 for capture source 0x24 in the second input source in
mixer).
Then to avoid noise when recording from digital mic with auto model in
this case, prevent a digital mic input source to be selected if
microphone is not available.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Tue, 11 Aug 2009 16:17:46 +0000 (18:17 +0200)]
ALSA: hda - Clean up init and setup hooks for Realtek codecs
Move static codes to setup from init_hook for each model.
Also, use the common auto-mic selection helper for devices that support
auto-mic selection. They just need to set up ext_mic, int_mic and
auto_mic flag in the setup section.
Takashi Iwai [Tue, 11 Aug 2009 15:16:13 +0000 (17:16 +0200)]
ALSA: hda - Add setup hook to ALC preset struct
Added setup hook to ALC preset struct to be called at in the parser
but not at each init callback.
This can be used for setting up the static pins, etc, while the
init hook should be used for updating the status again.
Takashi Iwai [Tue, 11 Aug 2009 12:21:26 +0000 (14:21 +0200)]
ALSA: hda - Add a white-list for MSI option
Created a white-list to enable MSI since some devices require MSI
explicitly due to BIOS/ACPI problems. Simply using a quirk list.
As the first case, take HP Compaq CQ40.
Takashi Iwai [Tue, 11 Aug 2009 07:47:30 +0000 (09:47 +0200)]
ALSA: hda - Check connectivity for auto-mic of Realtek codecs
Some Realtek codecs don't provide the full connections for certain pins
from each ADC; e.g. ACL662/ALC272 gives only one of two digital-mic pins
for each ADC. Thus, depending on the digital mic pin, the ADC/MUX to be
used has to be chosen properly.
This patch adds the check of the connectivity of pins at auto-mic mode.
If no proper connectivity is found, auto_mic flag is turned off to be
sure.
Also the mux_idx is determined during this check so it won't be checked
in the unsol event any more.
Takashi Iwai [Tue, 11 Aug 2009 06:45:11 +0000 (08:45 +0200)]
ALSA: hda - Don't override ADC definitions for ALC codecs
ALC269 and ALC861-VD parsers override the ADC definitions
unconditionally without checking the spec definition. This causes
the problem when any inconsistent ADC is set up in the device quirk
(like ALC272 with digital-mic).
This patch avoids the overriding by adding the proper checks.
Takashi Iwai [Mon, 10 Aug 2009 16:47:44 +0000 (18:47 +0200)]
ALSA: hda - Add auto-mic support for Realtek codecs
Added the support for automatic mic selection via plugging for
Realtek codecs (in auto-probing mode). The auto-mic mode is enabled
only when one internal mic and one external mic are present.
Takashi Iwai [Tue, 4 Aug 2009 11:40:54 +0000 (13:40 +0200)]
ALSA: hda - Fix line-out jack handling with STAC/IDT codec
When the line-out jack is plugged/unplugged, the driver needs to check
the headphone plug, not only the line-out jack itself. Otherwise the
headphone or the speaker may be wrongly muted/unmuted.
As a result, both STAC_HP_EVENT and STAC_LO_EVENT need to call the
same function, stac92xx_hp_detect().
Takashi Iwai [Mon, 3 Aug 2009 12:23:33 +0000 (14:23 +0200)]
ALSA: hda - Fix line-out jack detection
The commit fefd67f31ee7f5259344e36a237d59b47e8715cf
ALSA: hda - Add line-out jack detection on IDT/STAC codecs
enabled wrong pins for jack detections. Fixed to the correct ones.
Chengu Wang [Thu, 30 Jul 2009 11:43:55 +0000 (19:43 +0800)]
ALSA: hda: Correct EAPD for Dell Inspiron 1525
The commit 24918b61b55c21e09a3e07cd82e1b3a8154782dc statically changes
the model from dell-bios to dell-3stack to solve the sound decreasing
regression (http://lkml.org/lkml/2008/9/12/203), however it leads to another
problem that the 2nd headphone jack doesn't work
(https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3987). So I think
the commit 249**2dc is just a workaround. I would like to give a true solution
here.
The datasheet for STAC9228 says, GPIO2 is the same pin as VOL DOWN, and
the EAPD pin is GPIO0. This is why the sound decreases if we set EAPD as
GPIO2. This patch changes EAPD to GPIO0 to solve the problem.
Signed-off-by: Chengu Wang <wangchengu@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Wu Fengguang [Sat, 1 Aug 2009 10:45:16 +0000 (18:45 +0800)]
ALSA: hda: track CIRB/CORB command/response states for each codec
Recently we hit a bug in our dev board, whose HDMI codec#3 may emit
redundant/spurious responses, which were then taken as responses to
command for another onboard Realtek codec#2, and mess up both codecs.
Extend the azx_rb.cmds and azx_rb.res to array and track each codec's
commands/responses separately. This helps keep good codec safe from
broken ones.
Stelian Pop [Thu, 30 Jul 2009 12:44:27 +0000 (14:44 +0200)]
ALSA: hda - Enable HP output with Macbook Pro 5, 5
The patch below, to be applied on the latest sound-unstable-2.6.git,
enables headphones output on my MacBookPro 5,5, together with the
automuting feature.
Here is the exact soundcard id:
Vendor Id: 0x10134206
Subsystem Id: 0x106b4d00
Revision Id: 0x100301
ALSA: hda - Integrate Digital Input Source to Input Source
STAC/IDT codecs provide both "Input Source" and "Digital Input Source"
controls to choose the analog input source and the digital input source.
But this is far user-unfriendly.
This patch merges the input source selections into one "Input Source"
control. To have separate digital and analog input source controls,
you can pass "separate_dmux = 1 " hint string.
At the same time, this patch gets rid of analog mixer stuff that was
already disabled in previous patches.
ALSA: hda - Remove static connection in IDT 92HD71bxx
We don't need any more static connection to the port F (which is often
used for docking stations) since its connection is done dynamically via
DAC assignment now.
ALSA: hda - Support auto-mic switching with IDT/STAC codec
Support the automatic mic-switching with some devices with IDT/STAC
codecs. The condition is that the device has only two inputs, one
for an external mic and one for an internal mic.
ALSA: hda - Avoid overwrite of jack events with STAC/IDT
Since only one event can be associated to a (pin) widget, it's safer
to avoid the multiple mapping. This patch fixes the behavior of the
STAC/IDT codec driver.
Now stac_get_event() doesn't take the type argument but simply returns
the first hit element. Then enable_pin_detect() checks the validity
of the type, and returns non-zero only if a valid entry. The caller
can call stac_issue_unsol_event() after checking the return value.
Instead of static snd_kcontrol_new arrays, create "Capture Volume"
and "Capture Switch" controls dynamically based on the mixer attr
values (made via HDA_COMPOSE_AMP_VAL()).
This reduces the code size and gives more flexibility to change
the number of controls later.
ALSA: hda - Don't create unneeded digital input source for IDT 92HD71x
The current driver creates always the digital input source mixer
elements for IDT 92HD71x codecs no matter whether digital mics are
present. This patch adds the proper check to avoid the creation of
these controls if unnecessary.
ALSA: hda - Reword information messages for BIOS auto-probing mode
The sentense "Unknown model for xxx, ..." makes people too nervous
and drives them to a direction to a wrong "fix" by giving any
mismatching model option.
Let's rephrase the messages to be more nice and easy (at least that
won't make people suspect conspiracies).
projects / karo-tx-linux.git / log