Lots of users are getting confused about the cp2101 driver. It really
does support more than just the cp2101 device, so rename it to cp210x to
try to prevent confusion.
Craig Shelley [Thu, 26 Feb 2009 22:19:22 +0000 (22:19 +0000)]
USB: CP2101 Support AN205 baud rates
This patch adds support for the extended range of baud rates supported
by CP2102 and CP2103 devices described in SiLabs AN205. An additional
function cp2101_quantise_baudrate rounds the baud rate as per AN205
Table 1. A modification to the baud rate calculation removes a rounding
error, allowing the full range of baud rates to be used.
Alan Stern [Thu, 26 Feb 2009 15:21:02 +0000 (10:21 -0500)]
USB: don't send Set-Interface after reset
This patch (as1221) changes the way usbcore reinitializes a device
following a reset or a reset-resume. Currently we call
usb_set_interface() for every interface in the active configuration;
this is to put the interface into the same altsetting as before the
reset and to make sure that the host's endpoint state matches the
device's endpoint state.
However, sending a Set-Interface request is a waste of time if an
interface was already in altsetting 0 before the reset, since it is
certainly in altsetting 0 afterward. In addition, many devices can't
handle Set-Interface requests -- they crash when they receive them.
So instead, the patch adds code to check each interface. If the
interface wasn't in altsetting 0 before the reset, we go head with the
Set-Interface request as before. But if it was then we skip sending
the Set-Interface request, and we clear out the host-side endpoint
state by calling usb_disable_interface() followed by
usb_enable_interface().
The patch also adds a couple of new comments to explain what's going
on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These devices are better controlled with the LGPL userspace library
found at:
http://www.phidgets.com/downloads.php?os_id=3
and full documentation at:
http://www.phidgets.com/documentation/web/cdoc/index.html
Cc: Chester Fitchett <fitchett@phidgets.com> Acked-by: Sean Young <sean@mess.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
actual_length should also be a u32 and not a signed value. This patch
changes this field to be 'u32' to prevent any potential negative
conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
USB: make transfer_buffer_lengths in struct urb field u32
Roel Kluin pointed out that transfer_buffer_lengths in struct urb was
declared as an 'int'. This patch changes this field to be 'u32' to
prevent any potential negative conversion and comparison errors.
This triggered a few compiler warning messages when these fields were
being used with the min macro, so they have also been fixed up in this
patch.
Alan Stern [Thu, 5 Mar 2009 16:01:11 +0000 (11:01 -0500)]
USB: uhci: don't use pseudo negative values
The code in uhci-q.c doesn't have to use pseudo-negative values. I did
it that way because it was easy and because it would give the expected
output during debugging. But it doesn't have to work that way. Here's
another approach.
Jouni Hogander [Fri, 20 Feb 2009 12:02:31 +0000 (14:02 +0200)]
USB: TWL: disable VUSB regulators when cable unplugged
This patch disables USB regulators VUSB1V5, VUSB1V8, and VUSB3V1
when the USB cable is unplugged to reduce power consumption.
Added a depencency from twl4030 usb driver to TWL_REGULATOR.
Pete Zaitcev [Fri, 20 Feb 2009 05:54:45 +0000 (22:54 -0700)]
USB: usbmon: Add binary API v1
This patch adds an extension to the binary API so it reaches parity with
existing text API (so-called "1u"). The extension delivers additional data,
such as ISO descriptors and the interrupt interval.
Signed-Off-By: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ming Lei [Fri, 20 Feb 2009 13:23:09 +0000 (21:23 +0800)]
USB: ch341 serial: fix port number changed after resume
This patch fixes the following bug:
.plug ch341 usb serial port into a hub port;
.ch341 driver bound to the device and /dev/ttyUSB0 comes
.open /dev/ttyUSB0 by minicom and we can use the serial successfully
.suspend the ch341 usb serial device(such as: echo suspend > power/level)
.resume the ch341 usb serial device (such as: echo on > power/level)
.new port /dev/ttyUSB1 comes ,and the original /dev/ttyUSB0 still exists,
but is no longer usable by minicom
The patch adds suspend and resume callback to ch341 usb driver to prevent it
from unbinding during suspend. The /dev/ttyUSB0 is not released until being
closed, so /dev/ttyUSB1 comes after resume, and the original /dev/ttyUSB0 is
no longer usable by minicom. It is really a mess for a minicom user.
This patch also adds the reset_resume callback to make it usable after resuming
from STR or hibernation, for generally STR or hibernation will make the vbus
of root-hub lost.
Finally enable the driver's supports_autosuspend, for the device is in working
order with it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Except on DaVinci, VBUS is now switched off as part of idling the
USB link (after a_wait_bcon) whenever a device is disconnected
from host. This is correct for OTG hosts, where either SRP or
an ID interrupt could turn VBUS on again.
However, for non-OTG hosts there's no way to turn VBUS on again,
so the host becomes unusable. And the procfs entry which once
allowed a manual workaround for this is now gone.
This patch adds an is_otg_enabled() check before scheduling the
switch-off timer in disconnect path, supporting a "classic host"
mode where SRP is unavailable.
USB: musb: fix init oops crash with static FIFO config
Correct musb_read_fifosize() and musb_configure_ep0() functions
for the #ifndef BLACKFIN branch when the silicon uses static FIFO
configuration. (Most current silicon configures this controller
to use dynamic FIFO configuration; some parts from ST don't, like
the STM STA2062.)
Signed-off-by: Giuseppe GORGOGLIONE <giuseppe.gorgoglione@st.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes endpoint starvation issue when more than one bulk QH is
multiplexed on the reserved bulk RX endpoint, which is normal
for cases like serial and ethernet adapters.
This patch sets the NAK timeout interval for such QHs, and when
a timeout triggers the next QH will be scheduled. (This resembles
the bulk scheduling done in hardware by EHCI, OHCI, and UHCI.)
This scheme doesn't work for devices which are connected to a
high to full speed tree (transaction translator) as there is
no NAK timeout interrupt from the musb controller from such
devices.
Tested with PIO, Inventra DMA, CPPI DMA.
[ dbrownell@users.sourceforge.net: fold in start_urb() update;
clarify only for bulk RX; don't accidentally clear WZC bits ]
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current MUSB host code doesn't make use of all the available
FIFOs in for periodic transfers since it wrongly assumes the RX
and TX sides of any given hw_ep always share one FIFO.
Change: use 'in_qh' and 'out_qh' fields of the 'struct musb_hw_ep'
to check the endpoint's business; get rid of the now-unused 'periodic'
array in the 'struct musb'. Also optimize a loop induction variable
in the endpoint lookup code.
(Based on a previous patch from Ajay Kumar Gupta <ajay.gupta@ti.com>)
[ dbrownell@users.sourceforge.net: clarify description and origin
of this fix; whitespace ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Vrabel [Wed, 18 Feb 2009 14:43:47 +0000 (14:43 +0000)]
USB: allow libusb to talk to unauthenticated WUSB devices
To permit a userspace application to associate with WUSB devices
using numeric association, control transfers to unauthenticated WUSB
devices must be allowed.
This requires that wusbcore correctly sets the device state to
UNAUTHENTICATED, DEFAULT and ADDRESS and that control transfers can be
performed to UNAUTHENTICATED devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Maciej Grela [Sat, 28 Feb 2009 20:39:20 +0000 (12:39 -0800)]
USB: usb-storage: added missing MODULE_LICENSE("GPL") for usb-storage ums-* modules
The lack of a MODULE_LICENSE macro in ums-* subdrivers prevented them
from loading. Needs to be applied after Alan Stern's usb-storage
subdriver separation patchset. Also added missing MODULE_DESCRIPTION and
MODULE_AUTHOR entries.
Signed-off-by: Maciej Grela <maciej.grela@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 12 Feb 2009 19:47:49 +0000 (14:47 -0500)]
usb-storage: make sddr09 a separate module
This patch (as1207) converts usb-storage's sddr09 subdriver into a
separate module.
An unexpected complication arises because of DPCM devices, in which
one LUN uses the sddr09 transport and one uses the standard CB
transport. Since these devices can be used even when
USB_STORAGE_SDDR09 isn't configured, their entries in unusual_devs.h
require special treatment. If SDDR09 isn't configured then the
entries remain in unusual_devs.h; if it is then the entries are
present in unusual_sddr09.h instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 12 Feb 2009 19:47:44 +0000 (14:47 -0500)]
usb-storage: prepare for subdriver separation
This patch (as1206) is the first step in converting usb-storage's
subdrivers into separate modules. It makes the following large-scale
changes:
Remove a bunch of unnecessary #ifdef's from usb_usual.h.
Not truly necessary, but it does clean things up.
Move the USB device-ID table (which is duplicated between
libusual and usb-storage) into its own source file,
usual-tables.c, and arrange for this to be linked with
either libusual or usb-storage according to whether
USB_LIBUSUAL is configured.
Add to usual-tables.c a new usb_usual_ignore_device()
function to detect whether a particular device needs to be
managed by a subdriver and not by the standard handlers
in usb-storage.
Export a whole bunch of functions in usb-storage, renaming
some of them because their names don't already begin with
"usb_stor_". These functions will be needed by the new
subdriver modules.
Split usb-storage's probe routine into two functions.
The subdrivers will call the probe1 routine, then fill in
their transport and protocol settings, and then call the
probe2 routine.
Take the default cases and error checking out of
get_transport() and get_protocol(), which run during
probe1, and instead put a check for invalid transport
or protocol values into the probe2 function.
Add a new probe routine to be used for standard devices,
i.e., those that don't need a subdriver. This new routine
checks whether the device should be ignored (because it
should be handled by ub or by a subdriver), and if not,
calls the probe1 and probe2 functions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dave Young [Sat, 14 Feb 2009 13:21:13 +0000 (21:21 +0800)]
usb-serial: fix usb_serial_register bug when boot with nousb param
With "nousb" cmdline booting, built-in serial drivers (ie. airecable)
will trigger kernel oops.
Indeed, if nousb, usb_serial_init will failed, and the usb serial bus type
will not be registerd, then usb_serial_register call driver_register
which try to register the driver to a not registered bus.
Here add usb_disabled() check in usb_serial_register to fix it.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap [Fri, 13 Feb 2009 19:22:06 +0000 (11:22 -0800)]
USB: fix ehci printk formats
Fix ehci printk formats:
drivers/usb/host/ehci-q.c:351: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
drivers/usb/host/ehci-q.c:351: warning: format '%d' expects type 'int', but argument 5 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver originally written by Qualcomm, but rewritten by me due to the
totally different coding style. Cleaned up the probe logic to make a
bit more sense, this is one wierd device. They could have prevented all
of this by just writing sane firmware for the modem.
Cc: Tamm Liu <tamml@qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Catalin Marinas [Tue, 10 Feb 2009 16:55:51 +0000 (16:55 +0000)]
USB: Add platform device support for the ISP1760 USB chip
Currently, the driver only supports PCI and PPC_OF but there are
boards like ARM RealView where this is a platform device. The patch adds
the necessary functions and registration to the isp1760-if.c file and
modifies the corresponding Makefile and Kconfig to be able to use this
driver even if PCI and PPC_OF are not enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 10 Feb 2009 15:16:58 +0000 (10:16 -0500)]
USB: EHCI: add software retry for transaction errors
This patch (as1204) adds a software retry mechanism to ehci-hcd. It
gets invoked when the driver encounters transaction errors on an
asynchronous endpoint. On many systems, hardware deficiencies cause
such errors to occur if one device is unplugged while the host is
communicating with another device. With the patch, the failed
transactions are retried and generally succeed the second or third
time through.
This is based on code originally written by Koichiro Saito.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested by: Koichiro Saito <Saito.Koichiro@adniss.jp> CC: David Brownell <david-b@pacbell.net> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Boaz Harrosh [Wed, 11 Feb 2009 07:54:31 +0000 (09:54 +0200)]
USB: fix USB_STORAGE_CYPRESS_ATACB
commit 64a87b24: [SCSI] Let scsi_cmnd->cmnd use request->cmd buffer
changed the scsi_eh_prep_cmnd logic by making it clear
the ->cmnd buffer. But the sat to cypress atacb translation supposed
the ->cmnd buffer wasn't modified.
This patch makes it set the ->cmnd buffer after scsi_eh_prep_cmnd call.
The problem and a fix was reported by Matthieu CASTET <castet.matthieu@free.fr>
It also removes all the hackery fiddling of scsi_cmnd and scsi_eh_save by
requesting from scsi_eh_prep_cmnd to prepare a read into ->sense_buffer,
which is much more suitable a buffer for HW transfers, then after the command
execution the regs read is copied into regs buffer before actual preparation
of sense_buffer.
Also fix an alien comment character to my utf-8 editor.
Alan Stern [Wed, 11 Feb 2009 19:26:38 +0000 (14:26 -0500)]
USB: EHCI: Make timer_action out-of-line
This patch (as1205) moves timer_action() from ehci.h to ehci-hcd.c and
makes it out-of-line. Over the years it has grown too big to be inline
any more.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
James Woodcock [Wed, 11 Feb 2009 15:06:53 +0000 (15:06 +0000)]
USB: serial: refuse to open recently removed USB Serial devices
A USB-serial converter device is plugged into a system, and a process
opens it's device node. If the device is physically removed whilst the
process still has its device node open, then other processes can
sucessfully open the now non-existent device's node. I would expect
that open() on a device that has been physically removed should return
ENODEV.
This is manifesting itself with getty on my system. I do the following:
1. set up inittab to spawn getty on ttyUSB0, eg:
T1:23:respawn:/sbin/getty -L ttyUSB0 115200 vt100
2. Plug in USB-serial converter cable
3. Wait for a login prompt on a terminal program attached to the serial
cable
4. Login
5. Pull the USB-serial converter cable from the box
6. getty doesn't realise that ttyUSB0 no longer exists as /dev/ttyUSB0
can still be opened.
7. Re-insert the USB-serial converter cable
8. You should no longer get a login prompt over the serial cable, as
the the USB-serial cable now shows up as /dev/ttyUSB1, and getty is
trying to talk to /dev/ttyUSB0.
The attached patch will cause open("/dev/ttyUSB0", O_RDONLY) to return
ENODEV after the USB-serial converter has been pulled. The patch was
created against 2.6.28.1. I can supply it against something else if
needs be. It is fairly simple, so should be OK.
I am using a pl2303 device, although I don't think that makes any
difference.
From: James Woodcock <James.Woodcock@ACULAB.COM> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Mon, 9 Feb 2009 09:03:49 +0000 (10:03 +0100)]
USB: serial: remove recourse to generic method
This removes the fallback to the generic method. It is cleaner to
explicitely request it. Introducing this was my mistake. This will
be solved by an explicit test and the driver being allowed to request
what it needs to be done upon resumption.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This lets userspace determine what the state of the RTS line is, which
is what is needed to properly handle data flow for this device (it
raises RTS when there is data to be sent from it.)
NOP transceiver is used by all the usb transceiver which are mostly
autonomous and doesn't require any programming or which are built
into the usb ip itself.NOP transceiver only allocates the memory
for struct xceiv and calls otg_set_transceiver() so function call
to otg_get_transceiver() will return a valid transceiver.
NOP transceiver device should be registered by calling
usb_nop_xceiv_register() from platform files.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Fri, 6 Feb 2009 10:39:11 +0000 (02:39 -0800)]
USB: ftdi_sio: remove pointless syslog spew
Remove some pointless messages from the FTDI serial driver;
I found these filling up syslog on one system. Also remove
a pointless "break" after a "return" in the same area.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Frank Seidel [Thu, 5 Feb 2009 15:16:24 +0000 (16:16 +0100)]
USB: add missing KERN_* constants to printks
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing peaces here for the usb subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Fri, 6 Feb 2009 17:06:43 +0000 (18:06 +0100)]
USB: serial: use generic method if no alternative is provided in usb serial layer
This patch makes use of the generic method if a serial driver provides
no implementation. This simplifies implementing suspend/resume support
in serial drivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Fri, 6 Feb 2009 14:01:54 +0000 (15:01 +0100)]
USB: serial generic resume function fix
This removes an unnecessary check for autoresume from the generic
resume method. The check has been obsoleted by the now delayed
increase of the usage counter which makes the error this check prevented
impossible. This change allows drivers which only use the bulk read URB
the use of the generic method even if they support autosuspend.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Thu, 5 Feb 2009 15:54:25 +0000 (16:54 +0100)]
USB: serial: introduce a flag into the usb serial layer to tell drivers that their URBs are killed due to suspension
This patch introduces a flag into the usb serial layer to tell drivers
that their URBs are killed due to suspension. That is necessary to let
drivers know whether they should report an error back.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Hi Greg,
this is for 2.6.30. Patches to use this in drivers are under development.
Oliver Neukum [Tue, 27 Jan 2009 16:21:40 +0000 (17:21 +0100)]
USB: suspend/resume support for option driver
This patch implements suspend and resume methods for the
option driver. With my hardware I can even suspend the system
and keep up a connection for a short time.
Werner Cornelius [Fri, 16 Jan 2009 20:02:41 +0000 (21:02 +0100)]
USB: usb-serial ch341: support for DTR/RTS/CTS
Fixup of Werner Cornelius patch to the ch341 USB-serial driver, which adds:
- support all baudrates, not just a hard-coded set
- support for controlling DTR, RTS and CTS
Features still missing:
- character length other than 8 bits
- parity settings
- break control
I adapted his patch for the new usb_serial API introduced in 2.6.25-git8 by
Alan Cox on 22 July 2008. Non-compliance to the new API was a reason for
refusing a similar patch from Tollef Fog Heen.
Usage example by Tollef Fog Heen :
TEMPer USB thermometer <http://err.no/src/TEMPer.c>
Signed-off-by: Werner Cornelius <Werner.Cornelius@cornelius-consult.de> Signed-off-by: Boris Hajduk <boris@hajduk.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
are moved from include/linux/usb.h to include/linux/usb/ch9.h.
include/linux/usb/ch9.h makes more sense for these functions because they
only depend on constants that are defined in this file.
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Robert Jarzmik [Sun, 25 Jan 2009 07:59:38 +0000 (23:59 -0800)]
USB: pxa27x_udc: add vbus_draw callback
Add the vbus_draw() callback to inform the transceiver, if
it exists, how much current may be drawn. The decision is
taken on gadget driver side using the configuration chosen
by the host and its bMaxPower field. Some systems can use
the host's VBUS supply to augment or recharge a battery.
(There's also a default of 100 mA for unconfigured devices,
or 8 mA if they're OTG devices.)
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Robert Jarzmik [Sun, 25 Jan 2009 07:57:30 +0000 (23:57 -0800)]
USB: pxa27x_udc: add otg transceiver support
When a transceiver driver is used, no automatic udc enable
is done. The transceiver (OTG or not) should :
- take care of VBus sensing
- call usb_gadget_vbus_connect()
- call usb_gadget_vbus_disconnect()
The pullup should remain within this driver's management,
either by gpio_pullup of udc_command() fields.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Robert Jarzmik [Sun, 25 Jan 2009 07:56:42 +0000 (23:56 -0800)]
USB: pxa27x_udc: add vbus session handling
On vbus_session() call, optionally activate D+ pullup
resistor and enable the udc, or deactivate D+ pullup
resistor and disable the udc.
It is intentional to not handle any VBus sense related irq.
An external transceiver driver (like gpio_vbus) should
catch VBus sense signal, and call usb_gadget_vbus_connect()
or usb_gadget_vbus_disconnect().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Robert Jarzmik [Sun, 25 Jan 2009 07:55:34 +0000 (23:55 -0800)]
USB: pxa27x_udc: factor pullup code to prepare otg transceiver
Prepare pxa27x_udc to handle usb D+ pullup properly : it
should connect the pullup resistor and disconnect it only
if no external transceiver is handling it.
[ dbrownell@users.sourceforge.net: kerneldoc and gpio fixes ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Robert Jarzmik [Sun, 25 Jan 2009 07:54:31 +0000 (23:54 -0800)]
USB: gpio_vbus: add delayed vbus_session calls
Call usb_gadget_vbus_connect() and ...disconnect() from a
workqueue rather than from an irq handler, allowing msleep()
calls in vbus_session. Update kerneldoc to match.
[ dbrownell@users.sourceforge.net: more kerneldoc updates ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Wed, 7 Jan 2009 00:20:42 +0000 (17:20 -0700)]
usblp: continuously poll for status
The usblp in 2.6.18 polled for status regardless if we actually needed it.
At some point I dropped it, to save the batteries if nothing else.
As it turned out, printers exist (e.g. Canon BJC-3000) that need prodding
this way or else they stop. This patch restores the old behaviour.
If you want to save battery, don't leave jobs in the print queue.
I tested this on my printers by printing and examining usbmon traces
to make sure status is being requested and printers continue to print.
Tuomas Jäntti verified the fix on BJC-3000.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 23 Mar 2009 13:51:02 +0000 (09:51 -0400)]
USB: usb-storage: increase max_sectors for tape drives
This patch (as1203) increases the max_sector limit for USB tape
drives. By default usb-storage sets max_sectors to 240 (i.e., 120 KB)
for all devices. But tape drives need a higher limit, since tapes can
and do have very large block sizes. Without the ability to transfer
an entire large block in a single command, such tapes can't be used.
This fixes Bugzilla #12207.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Phil Mitchell <philipm@sybase.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Fri, 20 Mar 2009 08:08:20 +0000 (01:08 -0700)]
USB: gadget: fix rndis regression
Restore some code that was wrongly dropped from the RNDIS
driver, and caused interop problems observed with OpenMoko.
The issue is with hardware which needs help conforming to part
of the USB 2.0 spec (section 8.5.3.2); some can automagically
send a ZLP in response to an unexpected IN, but not all chips
will do that. We don't need to check the packet length ourselves
the way earlier code did, since the UDC must already check it.
But we do need to tell the UDC when it must force a short packet
termination of the data stage.
(Based on a patch from Aric D. Blumer <aric at sdgsystems.com>)
Alan Stern [Wed, 18 Mar 2009 18:28:53 +0000 (14:28 -0400)]
USB: add quirk to avoid config and interface strings
Apparently the Configuration and Interface strings aren't used as
often as the Vendor, Product, and Serial strings. In at least one
device (a Saitek Cyborg Gold 3D joystick), attempts to read the
Configuration string cause the device to stop responding to Control
requests.
This patch (as1226) adds a quirks flag, telling the kernel not to
read a device's Configuration or Interface strings, together with a
new quirk for the offending joystick.
Reported-by: Melchior FRANZ <melchior.franz@gmail.com> Tested-by: Melchior FRANZ <melchior.franz@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> [2.6.28 and 2.6.29, nothing earlier] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kyle McMartin [Mon, 23 Mar 2009 19:25:49 +0000 (15:25 -0400)]
Build with -fno-dwarf2-cfi-asm
With a sufficiently new compiler and binutils, code which wasn't
previously generating .eh_frame sections has begun to. Certain
architectures (powerpc, in this case) may generate unexpected relocation
formats in response to this, preventing modules from loading.
While the new relocation types should probably be handled, revert to the
previous behaviour with regards to generation of .eh_frame sections.
(This was reported against Fedora, which appears to be the only distro
doing any building against gcc-4.4 at present: RH bz#486545.)
Signed-off-by: Kyle McMartin <kyle@redhat.com> Acked-by: Roland McGrath <roland@redhat.com> Cc: Alexandre Oliva <aoliva@redhat.com> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
ucc_geth: Fix oops when using fixed-link support
dm9000: locking bugfix
net: update dnet.c for bus_id removal
dnet: DNET should depend on HAS_IOMEM
dca: add missing copyright/license headers
nl80211: Check that function pointer != NULL before using it
sungem: missing net_device_ops
be2net: fix to restore vlan ids into BE2 during a IF DOWN->UP cycle
be2net: replenish when posting to rx-queue is starved in out of mem conditions
bas_gigaset: correctly allocate USB interrupt transfer buffer
smsc911x: reset last known duplex and carrier on open
sh_eth: Fix mistake of the address of SH7763
sh_eth: Change handling of IRQ
netns: oops in ip[6]_frag_reasm incrementing stats
net: kfree(napi->skb) => kfree_skb
net: fix sctp breakage
ipv6: fix display of local and remote sit endpoints
net: Document /proc/sys/net/core/netdev_budget
tulip: fix crash on iface up with shirq debug
virtio_net: Make virtio_net support carrier detection
...
Miklos Szeredi [Mon, 23 Mar 2009 15:07:24 +0000 (16:07 +0100)]
fix ptrace slowness
This patch fixes bug #12208:
Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=12208
Subject : uml is very slow on 2.6.28 host
This turned out to be not a scheduler regression, but an already
existing problem in ptrace being triggered by subtle scheduler
changes.
The problem is this:
- task A is ptracing task B
- task B stops on a trace event
- task A is woken up and preempts task B
- task A calls ptrace on task B, which does ptrace_check_attach()
- this calls wait_task_inactive(), which sees that task B is still on the runq
- task A goes to sleep for a jiffy
- ...
Since UML does lots of the above sequences, those jiffies quickly add
up to make it slow as hell.
This patch solves this by not rescheduling in read_unlock() after
ptrace_stop() has woken up the tracer.
Thanks to Oleg Nesterov and Ingo Molnar for the feedback.
Anton Vorontsov [Mon, 23 Mar 2009 04:30:52 +0000 (21:30 -0700)]
ucc_geth: Fix oops when using fixed-link support
commit b1c4a9dddf09fe99b8f88252718ac5b357363dc4 ("ucc_geth: Change
uec phy id to the same format as gianfar's") introduced a regression
in the ucc_geth driver that causes this oops when fixed-link is used:
This patch fixes the issue by removing offending (and somewhat
duplicate) code from init_phy() routine, and changes _probe()
function to use uec_mdio_bus_name().
Also, since we fully construct phy_bus_id in the _probe() routine,
we no longer need ->phy_address and ->mdio_bus fields in
ucc_geth_info structure.
I wish the patch would be a bit shorter, but it seems like the only
way to fix the issue in a sane way. Luckily, the patch has been
tested with real PHYs and fixed-link, so no further regressions
expected.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Tested-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: David S. Miller <davem@davemloft.net>
David Brownell [Mon, 23 Mar 2009 04:28:39 +0000 (21:28 -0700)]
dm9000: locking bugfix
This fixes a locking bug in the dm9000 driver. It calls
request_irq() without setting IRQF_DISABLED ... which is
correct for handlers that support IRQ sharing, since that
behavior is not guaranteed for shared IRQs. However, its
IRQ handler then wrongly assumes that IRQs are blocked.
So the fix just uses the right spinlock primitives in the
IRQ handler.
NOTE: this is a classic example of the type of bug which
lockdep currently masks by forcibly setting IRQF_DISABLED
on IRQ handlers that did not request that flag.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 22 Mar 2009 18:38:57 +0000 (11:38 -0700)]
Merge branch 'fix-includes' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'fix-includes' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: merge the non-MMU and MMU versions of siginfo.h
m68k: use the MMU version of unistd.h for all m68k platforms
m68k: merge the non-MMU and MMU versions of signal.h
m68k: merge the non-MMU and MMU versions of ptrace.h
m68k: use MMU version of setup.h for both MMU and non-MMU
m68k: merge the non-MMU and MMU versions of sigcontext.h
m68k: merge the non-MMU and MMU versions of swab.h
m68k: merge the non-MMU and MMU versions of param.h
Tyler Hicks [Fri, 20 Mar 2009 07:23:57 +0000 (02:23 -0500)]
eCryptfs: NULL crypt_stat dereference during lookup
If ecryptfs_encrypted_view or ecryptfs_xattr_metadata were being
specified as mount options, a NULL pointer dereference of crypt_stat
was possible during lookup.
This patch moves the crypt_stat assignment into
ecryptfs_lookup_and_interpose_lower(), ensuring that crypt_stat
will not be NULL before we attempt to dereference it.
Thanks to Dan Carpenter and his static analysis tool, smatch, for
finding this bug.
Tyler Hicks [Fri, 20 Mar 2009 06:25:09 +0000 (01:25 -0500)]
eCryptfs: Allocate a variable number of pages for file headers
When allocating the memory used to store the eCryptfs header contents, a
single, zeroed page was being allocated with get_zeroed_page().
However, the size of an eCryptfs header is either PAGE_CACHE_SIZE or
ECRYPTFS_MINIMUM_HEADER_EXTENT_SIZE (8192), whichever is larger, and is
stored in the file's private_data->crypt_stat->num_header_bytes_at_front
field.
ecryptfs_write_metadata_to_contents() was using
num_header_bytes_at_front to decide how many bytes should be written to
the lower filesystem for the file header. Unfortunately, at least 8K
was being written from the page, despite the chance of the single,
zeroed page being smaller than 8K. This resulted in random areas of
kernel memory being written between the 0x1000 and 0x1FFF bytes offsets
in the eCryptfs file headers if PAGE_SIZE was 4K.
This patch allocates a variable number of pages, calculated with
num_header_bytes_at_front, and passes the number of allocated pages
along to ecryptfs_write_metadata_to_contents().
Thanks to Florian Streibelt for reporting the data leak and working with
me to find the problem. 2.6.28 is the only kernel release with this
vulnerability. Corresponds to CVE-2009-0787
radeonfb: Whack the PCI PM register until it sticks
This fixes a regression introduced when we switched to using the core
pci_set_power_state(). The chip seems to need the state to be written
over and over again until it sticks, so we do that.
Note that the code is a bit blunt, without timeout, etc... but that's
pretty much because I put back in there the code exactly as it used to
be before the regression. I still add a call to pci_set_power_state()
at the end so that ACPI gets called appropriately on x86.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Raymond Wooninck <tittiatcoke@gmail.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-beck.git / log