Linus Walleij [Wed, 17 Oct 2012 18:51:54 +0000 (20:51 +0200)]
pinctrl: reserve pins when states are activated
This switches the way that pins are reserved for multiplexing:
We used to do this when the map was parsed, at the creation of
the settings inside the pinctrl handle, in pinmux_map_to_setting().
However this does not work for us, because we want to use the
same set of pins with different devices at different times: the
current code assumes that the pin groups in a pinmux state will
only be used with one single device, albeit different groups can
be active at different times. For example if a single I2C driver
block is used to drive two different busses located on two
pin groups A and B, then the pins for all possible states of a
function are reserved when fetching the pinctrl handle: the
I2C bus can choose either set A or set B by a mux state at
runtime, but all pins in both group A and B (the superset) are
effectively reserved for that I2C function and mapped to the
device. Another device can never get in and use the pins in
group A, even if the device/function is using group B at the
moment.
Instead: let use reserve the pins when the state is activated
and drop them when the state is disabled, i.e. when we move to
another state. This way different devices/functions can use the
same pins at different times.
We know that this is an odd way of doing things, but we really
need to switch e.g. an SD-card slot to become a tracing output
sink at runtime: we plug in a special "tracing card" then mux
the pins that used to be an SD slot around to the tracing
unit and push out tracing data there instead of SD-card
traffic.
As a side effect pinmux_free_setting() is unused but the stubs
are kept for future additions of code.
Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Loic Pallardy <loic.pallardy@st.com> Acked-by: Stephen Warren <swarren@nvidia.com> Tested-by: Jean Nicolas Graux <jean-nicolas.graux@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
ChangeLog v2->v3:
- Keep pinmux_free_setting() stubs
Linus Walleij [Fri, 19 Oct 2012 15:06:54 +0000 (17:06 +0200)]
pinctrl/nomadik: use irq_create_mapping()
Since in the DT case, the linear domain path will not allocate
descriptors for the IRQs, we need to use irq_create_mapping()
for mapping hwirqs to Linux IRQs, so these descriptors get
created on-the-fly in this case.
Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:21 +0000 (10:11 +0200)]
Documentation: Update samsung-pinctrl device tree bindings documentation
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:20 +0000 (10:11 +0200)]
pinctrl: samsung: Add GPIO to IRQ translation
Some drivers require a way to translate GPIO pins to their IRQ numbers.
This patch adds the .to_irq() gpiolib callback to pinctrl-samsung
driver, which creates (if not present yet) and returns an IRQ mapping
for given GPIO pin.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:19 +0000 (10:11 +0200)]
pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
Pins used as wake-up interrupts need to be configured as EINTs. This
patch adds the required configuration code to exynos_wkup_irq_set_type,
to set the pin as EINT when its interrupt trigger type is configured.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:18 +0000 (10:11 +0200)]
pinctrl: samsung: Use per-bank IRQ domain for wake-up interrupts
This patch reworks wake-up interrupt handling in pinctrl-exynos driver,
so each pin bank, which provides wake-up interrupts, has its own IRQ
domain.
Information about whether given pin bank provides wake-up interrupts,
how many and whether they are separate or muxed are parsed from device
tree.
It gives following advantages:
- interrupts can be specified in device tree in a more readable way,
e.g. :
device {
/* ... */
interrupt-parent = <&gpx2>;
interrupts = <4 0>;
/* ... */
};
- the amount and layout of interrupts is not hardcoded in the code
anymore, but defined in SoC-specific structure
- bank and pin of each wake-up interrupt can be easily identified, to
allow operations, such as setting the pin to EINT function, from
irq_set_type() callback
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:17 +0000 (10:11 +0200)]
pinctrl: samsung: Use one GPIO chip per pin bank
This patch modifies the pinctrl-samsung driver to register one GPIO chip
per pin bank, instead of a single chip for all pin banks of the
controller.
It simplifies GPIO accesses a lot (constant time instead of looping
through the list of banks to find the right one) and should have a good
effect on performance of any bit-banging driver.
In addition it allows to reference GPIO pins by a phandle to the bank
node and a local pin offset inside of the bank (similar to previous
gpiolib driver), which is more clear and readable than using indices
relative to the whole pin controller.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:16 +0000 (10:11 +0200)]
pinctrl: exynos: Use one IRQ domain per pin bank
Instead of registering one IRQ domain for all pin banks of a pin
controller, this patch implements registration of per-bank domains.
At a cost of a little memory overhead (~2.5KiB for all GPIO interrupts
of Exynos4x12) it simplifies driver code and device tree sources,
because GPIO interrupts can be now specified per banks.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:15 +0000 (10:11 +0200)]
pinctrl: samsung: Include bank-specific eint offset in bank struct
Some SoCs, like Exynos4x12, have non-sequential layout of EINT control
registers and so current way of calculating register addresses does not
work correctly for them.
This patch adds eint_offset field to samsung_pin_bank struct and
modifies the driver to use it instead of calculating the offsets from
bank index.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:14 +0000 (10:11 +0200)]
pinctrl: samsung: Hold pointer to driver data in bank struct
This patch is a preparation for converting the pinctrl-samsung driver to
one GPIO chip and IRQ domain per bank. It allows one having only
a pointer to particular bank struct to access driver data struct.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:13 +0000 (10:11 +0200)]
pinctrl: samsung: Match pin banks with their device nodes
This patch is a preparation for converting the pinctrl-samsung driver to
one GPIO chip and IRQ domain per bank. It binds banks defined by
internal driver data with bank nodes in device tree.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:12 +0000 (10:11 +0200)]
ARM: dts: exynos4210-pinctrl: Add nodes for pin banks
This patch is a preparation for converting the pinctrl-samsung driver to
one GPIO chip and IRQ domain per bank. It allows particular banks to be
specified using their phandles.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:11 +0000 (10:11 +0200)]
pinctrl: samsung: Distinguish between pin group and bank nodes
This patch modifies the loop iterating over all child nodes and parsing
pin groups to check whether the node is really a pin group node by
checking for existence of samsung,pins property.
This is a prerequisite for further patches adding additional subnodes to
the pinctrl node, required for per bank GPIO and interrupt specifiers.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:10 +0000 (10:11 +0200)]
pinctrl: samsung: Remove static pin enumerations
Since pin numbers are now assigned dynamically, those are not needed
anymore.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:09 +0000 (10:11 +0200)]
pinctrl: samsung: Assing pin numbers dynamically
This patch modifies the pinctrl-samsung driver to assign numbers to pins
dynamically instead of static enumerations.
Thanks to this change the amount of code requried to support a SoC can
be greatly reduced and the code made more readable.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:08 +0000 (10:11 +0200)]
pinctrl: samsung: Do not pass gpio_chip to pin_to_reg_bank
The pointer to gpio_chip passed to pin_to_reg_bank utility function is
used only to retrieve a pointer to samsung_pinctrl_drv_data structure.
This patch modifies the function and its users to pass a pointer to
samsung_pinctrl_drv_data directly.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tomasz Figa [Thu, 11 Oct 2012 08:11:07 +0000 (10:11 +0200)]
pinctrl: samsung: Detect and handle unsupported configuration types
This patch modifies the pinctrl-samsung driver to detect when width of a
bit field is set to zero (which means that such configuraton type is not
supported) and return an error instead of trying to modify an inexistent
register.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Patrice Chotard [Mon, 8 Oct 2012 14:50:24 +0000 (16:50 +0200)]
pinctrl/nomadik: allow to support several ranges per GPIO bank
With DB8500 the number of GPIO chips = number GPIO bank =
number of GPIO ranges.
With DB8540, a new GPIO range configuration is used, some GPIO
banks can have several GPIO ranges.
For example, DB8540 GPIO bank0 (GPIO0 to GPIO32) have 2 GPIO
ranges:
- GPIO0 to GPIO17 : routed
- GPIO18 to GPIO21 : hole
- GPIO22 to GPIO28 : routed
- GPIO29 to GPIO32 : hole
Previously, during nmk_pinctrl_probe(), all GPIO ranges were
parsed, as GPIO ranges are larger than the number of GPIO chips,
a warning occurs. This commit allows each bank to have several
GPIO ranges.
Linus Walleij [Thu, 11 Oct 2012 14:33:44 +0000 (16:33 +0200)]
pinctrl/nomadik: always use the simple irqdomain
Since the simple irqdomain will fall back to a linear domain
if the first_irq provided is <= 0, just use this, just make
sure the first_irq is negative in the device tree case.
Cc: Rob Herring <rob.herring@calxeda.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 11 Oct 2012 12:33:42 +0000 (14:33 +0200)]
pinctrl/nomadik: provide stubs for legacy Nomadik
The compilation of the pinctrl driver failed on the legacy
Nomadik NHK8815 platform because it was not providing the PRCMU
interfaces needed to support the extended alternate functions
used by the ux500 series.
Solve this by providing some stubs for the legacy platform, to
avoid too much #ifdefs in the code per se. Theoretically this
actually allows the Nomadik and Ux500 to have a single kernel
image with support for the PRCM registers on the Ux500 (though
they have incompatible archs, but the spirit is there).
Arnd Bergmann [Tue, 9 Oct 2012 15:35:56 +0000 (15:35 +0000)]
pinctrl: sirf: remove sirfsoc_gpio_set_pull function
The prima2 platform advertises needing no mach/gpio.h header file,
but its pinctrl driver now has a sirfsoc_gpio_set_pull function
that uses constants defined in arch/arm/mach-prima2/include/mach/gpio.h,
which fails to build.
Fortunately, the sirfsoc_gpio_set_pull is not used anywhere in the
kernel, so we can safely remove it. Any out of tree drivers using
it will have to be converted to use proper pinctrl functions to
do the same.
Without this patch, building prima2_defconfig results in:
drivers/pinctrl/pinctrl-sirf.c: In function 'sirfsoc_gpio_set_pull':
drivers/pinctrl/pinctrl-sirf.c:1331:7: error: 'SIRFSOC_GPIO_PULL_NONE' undeclared (first use in this function)
drivers/pinctrl/pinctrl-sirf.c:1331:7: note: each undeclared identifier is reported only once for each function it appears in
drivers/pinctrl/pinctrl-sirf.c:1334:7: error: 'SIRFSOC_GPIO_PULL_UP' undeclared (first use in this function)
drivers/pinctrl/pinctrl-sirf.c:1338:7: error: 'SIRFSOC_GPIO_PULL_DOWN' undeclared (first use in this function)
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: samsung: use __devinit section for init code
The samsung pinctrl driver has a probe function that is
__devinit and that calls a lot of other functions that are
marked __init, which kbuild complains about.
Marking everything __devinit means that the code does not
discarded when CONFIG_HOTPLUG is set, which is a little
more wasteful, but also more consistent
Without this patch, building exynos_defconfig results in:
WARNING: drivers/pinctrl/built-in.o(.devinit.text+0x124): Section mismatch in reference from the function samsung_pinctrl_probe() to the function .init.text:samsung_gpiolib_register()
The function __devinit samsung_pinctrl_probe() references
a function __init samsung_gpiolib_register().
If samsung_gpiolib_register is only used by samsung_pinctrl_probe then
annotate samsung_gpiolib_register with a matching annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Thomas Abraham <thomas.abraham@linaro.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds [Sun, 14 Oct 2012 21:39:05 +0000 (14:39 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS update from Ralf Baechle:
"Cleanups and fixes for breakage that occured earlier during this merge
phase. Also a few patches that didn't make the first pull request.
Of those is the Alchemy work that merges code for many of the SOCs and
evaluation boards thus among other code shrinkage, reduces the number
of MIPS defconfigs by 5."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits)
MIPS: SNI: Switch RM400 serial to SCCNXP driver
MIPS: Remove unused empty_bad_pmd_table[] declaration.
MIPS: MT: Remove kspd.
MIPS: Malta: Fix section mismatch.
MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets.
MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code.
MIPS: Alchemy: merge PB1550 support into DB1550 code
MIPS: Alchemy: Single kernel for DB1200/1300/1550
MIPS: Optimize TLB refill for RI/XI configurations.
MIPS: proc: Cleanup printing of ASEs.
MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.
MIPS: Add detection of DSP ASE Revision 2.
MIPS: Optimize pgd_init and pmd_init
MIPS: perf: Add perf functionality for BMIPS5000
MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
MIPS: perf: Remove unnecessary #ifdef
MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
vmlinux.lds.h: Allow architectures to add sections to the front of .bss
...
Linus Torvalds [Sun, 14 Oct 2012 20:39:34 +0000 (13:39 -0700)]
Merge branch 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
Matt Fleming [Fri, 12 Oct 2012 10:19:59 +0000 (11:19 +0100)]
x86, boot: Explicitly include autoconf.h for hostprogs
The hostprogs need access to the CONFIG_* symbols found in
include/generated/autoconf.h. But commit abbf1590de22 ("UAPI: Partition
the header include path sets and add uapi/ header directories") replaced
$(LINUXINCLUDE) with $(USERINCLUDE) which doesn't contain the necessary
include paths.
This has the undesirable effect of breaking the EFI boot stub because
the #ifdef CONFIG_EFI_STUB code in arch/x86/boot/tools/build.c is
never compiled.
It should also be noted that because $(USERINCLUDE) isn't exported by
the top-level Makefile it's actually empty in arch/x86/boot/Makefile.
Cc: H. Peter Anvin <hpa@zytor.com> Cc: Ingo Molnar <mingo@kernel.org> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 14 Oct 2012 00:18:53 +0000 (17:18 -0700)]
Merge branch 'late-for-linus' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM update from Russell King:
"This is the final round of stuff for ARM, left until the end of the
merge window to reduce the number of conflicts. This set contains the
ARM part of David Howells UAPI changes, and a fix to the ordering of
'select' statements in ARM Kconfig files (see the appropriate commit
for why this happened - thanks to Andrew Morton for pointing out the
problem.)
I've left this as long as I dare for this window to avoid conflicts,
and I regenerated the config patch yesterday, posting it to our
mailing list for review and testing. I have several acks which
include successful test reports for it.
However, today I notice we've got new conflicts with previously unseen
code... though that conflict should be trivial (it's my changes vs a
one liner.)"
* 'late-for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: config: make sure that platforms are ordered by option string
ARM: config: sort select statements alphanumerically
UAPI: (Scripted) Disintegrate arch/arm/include/asm
Fix up fairly conflict in arch/arm/Kconfig (the select re-organization
vs recent addition of GENERIC_KERNEL_EXECVE)
Linus Torvalds [Sat, 13 Oct 2012 20:28:32 +0000 (13:28 -0700)]
Merge tag 'disintegrate-main-20121013' of git://git.infradead.org/users/dhowells/linux-headers
Pull UAPI disintegration for include/linux/{,byteorder/}*.h from David Howells:
"The patches contained herein do the following:
(1) Remove kernel-only stuff in linux/ppp-comp.h from the UAPI. I checked
this with Paul Mackerras before I created the patch and he suggested some
extra bits to unexport.
(2) Remove linux/blk_types.h entirely from the UAPI as none of it is userspace
applicable, and remove from the UAPI that part of linux/fs.h that was the
reason for linux/blk_types.h being exported in the first place. I
discussed this with Jens Axboe before creating the patch.
(3) The big patch of the series to disintegrate include/linux/*.h as a unit.
This could be split up, though there would be collisions in moving stuff
between the two Kbuild files when the parts are merged as that file is
sorted alphabetically rather than being grouped by subsystem.
Of this set of headers, 17 files have changed in the UAPI exported region
since the 4th and only 8 since the 9th so there isn't much change in this
area - as one might expect.
It should be pretty obvious and straightforward if it does come to fixing
up: stuff in __KERNEL__ guards stays where it is and stuff outside moves
to the same file in the include/uapi/linux/ directory.
If a new file appears then things get a bit more complicated as the
"headers +=" line has to move to include/uapi/linux/Kbuild. Only one new
file has appeared since the 9th and I judge this type of event relatively
unlikely.
(4) A patch to disintegrate include/linux/byteorder/*.h as a unit.
Signed-off-by: David Howells <dhowells@redhat.com>"
* tag 'disintegrate-main-20121013' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/linux/byteorder
UAPI: (Scripted) Disintegrate include/linux
UAPI: Unexport linux/blk_types.h
UAPI: Unexport part of linux/ppp-comp.h
Linus Torvalds [Sat, 13 Oct 2012 20:26:39 +0000 (13:26 -0700)]
Merge tag 'disintegrate-spi-20121009' of git://git.infradead.org/users/dhowells/linux-headers
Pull spi UAPI disintegration from David Howells:
"This is to complete part of the Userspace API (UAPI) disintegration
for which the preparatory patches were pulled recently. After these
patches, userspace headers will be segregated into:
include/uapi/linux/.../foo.h
for the userspace interface stuff, and:
include/linux/.../foo.h
for the strictly kernel internal stuff.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Grant Likely <grant.likely@secretlab.ca>"
* tag 'disintegrate-spi-20121009' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/linux/spi
Linus Torvalds [Sat, 13 Oct 2012 20:23:39 +0000 (13:23 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull user namespace compile fixes from Eric W Biederman:
"This tree contains three trivial fixes. One compiler warning, one
thinko fix, and one build fix"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
btrfs: Fix compilation with user namespace support enabled
userns: Fix posix_acl_file_xattr_userns gid conversion
userns: Properly print bluetooth socket uids
Linus Torvalds [Sat, 13 Oct 2012 20:22:01 +0000 (13:22 -0700)]
Merge tag 'md-3.7' of git://neil.brown.name/md
Pull md updates from NeilBrown:
- "discard" support, some dm-raid improvements and other assorted bits
and pieces.
* tag 'md-3.7' of git://neil.brown.name/md: (29 commits)
md: refine reporting of resync/reshape delays.
md/raid5: be careful not to resize_stripes too big.
md: make sure manual changes to recovery checkpoint are saved.
md/raid10: use correct limit variable
md: writing to sync_action should clear the read-auto state.
Subject: [PATCH] md:change resync_mismatches to atomic64_t to avoid races
md/raid5: make sure to_read and to_write never go negative.
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
md/raid5: protect debug message against NULL derefernce.
md/raid5: add some missing locking in handle_failed_stripe.
MD: raid5 avoid unnecessary zero page for trim
MD: raid5 trim support
md/bitmap:Don't use IS_ERR to judge alloc_page().
md/raid1: Don't release reference to device while handling read error.
raid: replace list_for_each_continue_rcu with new interface
add further __init annotations to crypto/xor.c
DM RAID: Fix for "sync" directive ineffectiveness
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
DM RAID: Add rebuild capability for RAID10
DM RAID: Move 'rebuild' checking code to its own function
...
Russell King [Fri, 12 Oct 2012 13:20:52 +0000 (14:20 +0100)]
ARM: config: make sure that platforms are ordered by option string
The large platform selection choice should be sorted by option string
so it's easy to find the platform you're looking for. Fix the few
options which are out of this order.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Stephen Warren <swarren@nvidia.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michael Kerrisk <mtk.manpages@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Dave Jones <davej@redhat.com>
David Howells [Sat, 13 Oct 2012 09:46:48 +0000 (10:46 +0100)]
UAPI: (Scripted) Disintegrate include/linux
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michael Kerrisk <mtk.manpages@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Dave Jones <davej@redhat.com>
David Howells [Sat, 13 Oct 2012 09:45:06 +0000 (10:45 +0100)]
UAPI: Unexport linux/blk_types.h
It seems that was linux/blk_types.h incorrectly exported to fix up some missing
bits required by the exported parts of linux/fs.h (READ, WRITE, READA, etc.).
So unexport linux/blk_types.h and unexport the relevant bits of linux/fs.h.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jens Axboe <jaxboe@fusionio.com>
cc: Tejun Heo <tj@kernel.org>
cc: Al Viro <viro@ZenIV.linux.org.uk>
Jonas Bonn [Sat, 13 Oct 2012 05:38:37 +0000 (07:38 +0200)]
Merge tag 'disintegrate-openrisc-20121009' of git://git.infradead.org/users/dhowells/linux-headers
UAPI Disintegration 2012-10-09
* tag 'disintegrate-openrisc-20121009' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate arch/openrisc/include/asm
Linus Torvalds [Sat, 13 Oct 2012 02:29:00 +0000 (11:29 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull TPM bugfixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: Propagate error from tpm_transmit to fix a timeout hang
driver/char/tpm: fix regression causesd by ppi
Linus Torvalds [Sat, 13 Oct 2012 02:27:59 +0000 (11:27 +0900)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull ACPI & Thermal updates from Len Brown:
"The generic Linux thermal layer is gaining some new capabilities
(generic cooling via cpufreq) and some new customers (ARM).
Also, an ACPI EC bug fix plus a regression fix."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (30 commits)
tools/power/acpi/acpidump: remove duplicated include from acpidump.c
ACPI idle, CPU hotplug: Fix NULL pointer dereference during hotplug
cpuidle / ACPI: fix potential NULL pointer dereference
ACPI: EC: Add a quirk for CLEVO M720T/M730T laptop
ACPI: EC: Make the GPE storm threshold a module parameter
thermal: Exynos: Fix NULL pointer dereference in exynos_unregister_thermal()
Thermal: Fix bug on cpu_cooling, cooling device's id conflict problem.
thermal: exynos: Use devm_* functions
ARM: exynos: add thermal sensor driver platform data support
thermal: exynos: register the tmu sensor with the kernel thermal layer
thermal: exynos5: add exynos5250 thermal sensor driver support
hwmon: exynos4: move thermal sensor driver to driver/thermal directory
thermal: add generic cpufreq cooling implementation
Fix a build error.
thermal: Fix potential NULL pointer accesses
thermal: add Renesas R-Car thermal sensor support
thermal: fix potential out-of-bounds memory access
Thermal: Introduce locking for cdev.thermal_instances list.
Thermal: Unify the code for both active and passive cooling
Thermal: Introduce simple arbitrator for setting device cooling state
...
Linus Torvalds [Sat, 13 Oct 2012 02:25:41 +0000 (11:25 +0900)]
Merge tag 'for-3.7' of git://openrisc.net/jonas/linux
Pull OpenRISC updates from Jonas Bonn:
"Fixups for some corner cases, build issues, and some obvious bugs in
IRQ handling. No major changes."
* tag 'for-3.7' of git://openrisc.net/jonas/linux:
openrisc: mask interrupts in irq_mask_ack function
openrisc: fix typos in comments and warnings
openrisc: PIC should act on domain-local irqs
openrisc: Make cpu_relax() invoke barrier()
audit: define AUDIT_ARCH_OPENRISC
openrisc: delay: fix handling of counter overflow
openrisc: delay: fix loops calculation for __const_udelay
Linus Torvalds [Sat, 13 Oct 2012 02:20:04 +0000 (11:20 +0900)]
Merge tag 'arm64-uapi' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 uapi disintegration from Catalin Marinas:
"UAPI headers for arm64 together with some clean-up to make it
possible:
- Do not export the COMPAT_* definitions to user
- Simplify the compat unistd32.h definitions and remove the
__SYSCALL_COMPAT guard
- Disintegrate the arch/arm64/include/asm/* headers"
* tag 'arm64-uapi' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
UAPI: (Scripted) Disintegrate arch/arm64/include/asm
arm64: Do not export the compat-specific definitions to the user
arm64: Do not include asm/unistd32.h in asm/unistd.h
arm64: Remove unused definitions from asm/unistd32.h
Linus Torvalds [Sat, 13 Oct 2012 02:16:58 +0000 (11:16 +0900)]
Merge tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB fixes and cleanups from Jason Wessel:
"Cleanups
- Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
- Add module event hooks for simplified debugging with gdb
Fixes
- Fix kdb to stop paging with 'q' on bta and dmesg
- Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
- The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
- Allow kgdboc=kdb to setup kdb on the vga console"
* tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
tty/console: fix warnings in drivers/tty/serial/kgdboc.c
kdb,vt_console: Fix missed data due to pager overruns
kdb: Fix dmesg/bta scroll to quit with 'q'
kgdboc: Accept either kbd or kdb to activate the vga + keyboard kdb shell
kgdb,x86: fix warning about unused variable
mips,kgdb: fix recursive page fault with CONFIG_KPROBES
kgdb: Add module event hooks
Linus Torvalds [Sat, 13 Oct 2012 01:57:57 +0000 (10:57 +0900)]
Merge tag 'dm-3.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper changes from Alasdair G Kergon:
"Remove the power-of-2 block size constraint on discards in dm thin
provisioning and factor the bio_prison code out into a separate module
(for sharing with the forthcoming cache target).
Use struct bio's front_pad to eliminate the use of one separate
mempool by bio-based devices.
A few other tiny clean-ups."
* tag 'dm-3.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm: store dm_target_io in bio front_pad
dm thin: move bio_prison code to separate module
dm thin: prepare to separate bio_prison code
dm thin: support discard with non power of two block size
dm persistent data: convert to use le32_add_cpu
dm: use ACCESS_ONCE for sysfs values
dm bufio: use list_move
dm mpath: fix check for null mpio in end_io fn
Linus Torvalds [Sat, 13 Oct 2012 01:57:01 +0000 (10:57 +0900)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull misc SCSI updates from James Bottomley:
"This is an assorted set of stragglers into the merge window with
driver updates for megaraid_sas, lpfc, bfi and mvumi. It also
includes some fairly major fixes for virtio-scsi (scatterlist init),
scsi_debug (off by one error), storvsc (use after free) and qla2xxx
(potential deadlock).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (49 commits)
[SCSI] storvsc: Account for in-transit packets in the RESET path
[SCSI] qla2xxx: fix potential deadlock on ha->hardware_lock
[SCSI] scsi_debug: Fix off-by-one bug when unmapping region
[SCSI] Shorten the path length of scsi_cmd_to_driver()
[SCSI] virtio-scsi: support online resizing of disks
[SCSI] virtio-scsi: fix LUNs greater than 255
[SCSI] virtio-scsi: initialize scatterlist structure
[SCSI] megaraid_sas: Version, Changelog, Copyright update
[SCSI] megaraid_sas: Remove duplicate code
[SCSI] megaraid_sas: Add SystemPD FastPath support
[SCSI] megaraid_sas: Add array boundary check for SystemPD
[SCSI] megaraid_sas: Load io_request DataLength in bytes
[SCSI] megaraid_sas: Add module param for configurable MSI-X vector count
[SCSI] megaraid_sas: Remove un-needed completion_lock spinlock calls
[SCSI] lpfc 8.3.35: Update lpfc version for 8.3.35 driver release
[SCSI] lpfc 8.3.35: Fixed not reporting logical link speed to SCSI midlayer when QoS not on
[SCSI] lpfc 8.3.35: Fix error with fabric service parameters causing performance issues
[SCSI] lpfc 8.3.35: Fixed SCSI host create showing wrong link speed on SLI3 HBA ports
[SCSI] lpfc 8.3.35: Fixed not checking solicition in progress bit when verifying FCF record for use
[SCSI] lpfc 8.3.35: Fixed messages for misconfigured port errors
...
Linus Torvalds [Sat, 13 Oct 2012 01:56:03 +0000 (10:56 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input layer updates from Dmitry Torokhov:
"2nd round of updates for the input subsystem. With it input core no
longer limits number of character devices per event handler (such as
evdev) to 32, but switches to dynamic minors once legacy range is
exhausted. This should get multi-seat installations that currently
run our of event devices very quickly.
You will also get an update for Wacom driver and a couple of driver
fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: extend the number of event (and other) devices
Input: mousedev - mark mousedev interfaces as non-seekable
Input: mousedev - rename mixdev_open to opened_by_mixdev
Input: mousedev - reformat structure initializers
Input: mousedev - factor out psaux code to reduce #ifdefery
Input: samsung-keypad - add clk_prepare and clk_unprepare
Input: atmel_mxt_ts - simplify mxt_dump_message
Input: wacom - clean up wacom_query_tablet_data
Input: wacom - introduce wacom_fix_phy_from_hid
Input: wacom - allow any multi-input Intuos device to set prox
Input: wacom - report correct touch contact size for I5/Bamboo
Linus Torvalds [Sat, 13 Oct 2012 01:53:54 +0000 (10:53 +0900)]
Merge branch 'for-3.7' of git://linux-nfs.org/~bfields/linux
Pull nfsd update from J Bruce Fields:
"Another relatively quiet cycle. There was some progress on my
remaining 4.1 todo's, but a couple of them were just of the form
"check that we do X correctly", so didn't have much affect on the
code.
Other than that, a bunch of cleanup and some bugfixes (including an
annoying NFSv4.0 state leak and a busy-loop in the server that could
cause it to peg the CPU without making progress)."
* 'for-3.7' of git://linux-nfs.org/~bfields/linux: (46 commits)
UAPI: (Scripted) Disintegrate include/linux/sunrpc
UAPI: (Scripted) Disintegrate include/linux/nfsd
nfsd4: don't allow reclaims of expired clients
nfsd4: remove redundant callback probe
nfsd4: expire old client earlier
nfsd4: separate session allocation and initialization
nfsd4: clean up session allocation
nfsd4: minor free_session cleanup
nfsd4: new_conn_from_crses should only allocate
nfsd4: separate connection allocation and initialization
nfsd4: reject bad forechannel attrs earlier
nfsd4: enforce per-client sessions/no-sessions distinction
nfsd4: set cl_minorversion at create time
nfsd4: don't pin clientids to pseudoflavors
nfsd4: fix bind_conn_to_session xdr comment
nfsd4: cast readlink() bug argument
NFSD: pass null terminated buf to kstrtouint()
nfsd: remove duplicate init in nfsd4_cb_recall
nfsd4: eliminate redundant nfs4_free_stateid
fs/nfsd/nfs4idmap.c: adjust inconsistent IS_ERR and PTR_ERR
...
1) Alexey Kuznetsov noticed we routed TCP resets improperly in the
assymetric routing case, fix this by reverting a change that made us
use the incoming interface in the outgoing route key when we didn't
have a socket context to work with.
2) TCP sysctl kernel memory leakage to userspace fix from Alan Cox.
3) Move UAPI bits from David Howells, WIMAX and CAN this time.
4) Fix TX stalls in e1000e wrt. Byte Queue Limits, from Hiroaki
SHIMODA, Denys Fedoryshchenko, and Jesse Brandeburg.
5) Fix IPV6 crashes in packet generator module, from Amerigo Wang.
6) Tidies and fixes in the new VXLAN driver from Stephen Hemminger.
7) Bridge IP options parse doesn't check first if SKB header has at
least an IP header's worth of content present. Fix from Sarveshwar
Bandi.
8) The kernel now generates compound pages on transmit and the Xen
netback drivers needs some adjustments in order to handle this. Fix
from Ian Campbell.
9) Turn off ASPM in JME driver, from Kevin Bardon and Matthew Garrett.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
mcs7830: Fix link state detection
net: add doc for in4_pton()
net: add doc for in6_pton()
vti: fix sparse bit endian warnings
tcp: resets are misrouted
usbnet: Support devices reporting idleness
Add CDC-ACM support for the CX93010-2x UCMxx USB Modem
net/ethernet/jme: disable ASPM
tcp: sysctl interface leaks 16 bytes of kernel memory
kaweth: print correct debug ptr
e1000e: Change wthresh to 1 to avoid possible Tx stalls
ipv4: fix route mark sparse warning
xen: netback: handle compound page fragments on transmit.
bridge: Pull ip header into skb->data before looking into ip header.
isdn: fix a wrapping bug in isdn_ppp_ioctl()
vxlan: fix oops when give unknown ifindex
vxlan: fix receive checksum handling
vxlan: add additional headroom
vxlan: allow configuring port range
vxlan: associate with tunnel socket on transmit
...
Pull tile arch update from Chris Metcalf:
"The bulk of this change is the tile uapi disintegration. There is
also a one-line change in here to enable interrupts in
do_work_pending() to avoid a WARN_ON in _local_bh_enable_ip()."
Linus Torvalds [Sat, 13 Oct 2012 01:20:11 +0000 (10:20 +0900)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"This tree includes some late late perf items that missed the first
round:
tools:
- Bash auto completion improvements, now we can auto complete the
tools long options, tracepoint event names, etc, from Namhyung Kim.
- Look up thread using tid instead of pid in 'perf sched'.
- Move global variables into a perf_kvm struct, from David Ahern.
- Hists refactorings, preparatory for improved 'diff' command, from
Jiri Olsa.
- Hists refactorings, preparatory for event group viewieng work, from
Namhyung Kim.
- Remove double negation on optional feature macro definitions, from
Namhyung Kim.
- Remove several cases of needless global variables, on most
builtins.
- misc fixes
kernel:
- sysfs support for IBS on AMD CPUs, from Robert Richter.
- Support for an upcoming Intel CPU, the Xeon-Phi / Knights Corner
HPC blade PMU, from Vince Weaver.
- misc fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
perf: Fix perf_cgroup_switch for sw-events
perf: Clarify perf_cpu_context::active_pmu usage by renaming it to ::unique_pmu
perf/AMD/IBS: Add sysfs support
perf hists: Add more helpers for hist entry stat
perf hists: Move he->stat.nr_events initialization to a template
perf hists: Introduce struct he_stat
perf diff: Removing the total_period argument from output code
perf tool: Add hpp interface to enable/disable hpp column
perf tools: Removing hists pair argument from output path
perf hists: Separate overhead and baseline columns
perf diff: Refactor diff displacement possition info
perf hists: Add struct hists pointer to struct hist_entry
perf tools: Complete tracepoint event names
perf/x86: Add support for Intel Xeon-Phi Knights Corner PMU
perf evlist: Remove some unused methods
perf evlist: Introduce add_newtp method
perf kvm: Move global variables into a perf_kvm struct
perf tools: Convert to BACKTRACE_SUPPORT
perf tools: Long option completion support for each subcommands
perf tools: Complete long option names of perf command
...
It is needed to configure the pin as PIO at "request time" when we are
using DT. Indeed, the muxing via old AT91 API is not allowed anymore if
we are using the plain gpiolib.
Linus Torvalds [Sat, 13 Oct 2012 01:05:52 +0000 (10:05 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Pull third pile of kernel_execve() patches from Al Viro:
"The last bits of infrastructure for kernel_thread() et.al., with
alpha/arm/x86 use of those. Plus sanitizing the asm glue and
do_notify_resume() on alpha, fixing the "disabled irq while running
task_work stuff" breakage there.
At that point the rest of kernel_thread/kernel_execve/sys_execve work
can be done independently for different architectures. The only
pending bits that do depend on having all architectures converted are
restrictred to fs/* and kernel/* - that'll obviously have to wait for
the next cycle.
I thought we'd have to wait for all of them done before we start
eliminating the longjump-style insanity in kernel_execve(), but it
turned out there's a very simple way to do that without flagday-style
changes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
alpha: switch to saner kernel_execve() semantics
arm: switch to saner kernel_execve() semantics
x86, um: convert to saner kernel_execve() semantics
infrastructure for saner ret_from_kernel_thread semantics
make sure that kernel_thread() callbacks call do_exit() themselves
make sure that we always have a return path from kernel_execve()
ppc: eeh_event should just use kthread_run()
don't bother with kernel_thread/kernel_execve for launching linuxrc
alpha: get rid of switch_stack argument of do_work_pending()
alpha: don't bother passing switch_stack separately from regs
alpha: take SIGPENDING/NOTIFY_RESUME loop into signal.c
alpha: simplify TIF_NEED_RESCHED handling
Linus Torvalds [Sat, 13 Oct 2012 01:04:42 +0000 (10:04 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull third pile of VFS updates from Al Viro:
"Stuff from Jeff Layton, mostly. Sanitizing interplay between audit
and namei, removing a lot of insanity from audit_inode() mess and
getting things ready for his ESTALE patchset."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
procfs: don't need a PATH_MAX allocation to hold a string representation of an int
vfs: embed struct filename inside of names_cache allocation if possible
audit: make audit_inode take struct filename
vfs: make path_openat take a struct filename pointer
vfs: turn do_path_lookup into wrapper around struct filename variant
audit: allow audit code to satisfy getname requests from its names_list
vfs: define struct filename and have getname() return it
vfs: unexport getname and putname symbols
acct: constify the name arg to acct_on
vfs: allocate page instead of names_cache buffer in mount_block_root
audit: overhaul __audit_inode_child to accomodate retrying
audit: optimize audit_compare_dname_path
audit: make audit_compare_dname_path use parent_len helper
audit: remove dirlen argument to audit_compare_dname_path
audit: set the name_len in audit_inode for parent lookups
audit: add a new "type" field to audit_names struct
audit: reverse arguments to audit_inode_child
audit: no need to walk list in audit_inode if name is NULL
audit: pass in dentry to audit_copy_inode wherever possible
audit: remove unnecessary NULL ptr checks from do_path_lookup
Jeff Layton [Wed, 10 Oct 2012 20:43:13 +0000 (16:43 -0400)]
vfs: embed struct filename inside of names_cache allocation if possible
In the common case where a name is much smaller than PATH_MAX, an extra
allocation for struct filename is unnecessary. Before allocating a
separate one, try to embed the struct filename inside the buffer first. If
it turns out that that's not long enough, then fall back to allocating a
separate struct filename and redoing the copy.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Jeff Layton [Wed, 10 Oct 2012 20:43:13 +0000 (16:43 -0400)]
audit: make audit_inode take struct filename
Keep a pointer to the audit_names "slot" in struct filename.
Have all of the audit_inode callers pass a struct filename ponter to
audit_inode instead of a string pointer. If the aname field is already
populated, then we can skip walking the list altogether and just use it
directly.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
projects / karo-tx-linux.git / log