Laxman Dewangan [Wed, 13 Mar 2013 19:49:51 +0000 (01:19 +0530)]
ARM: tegra: add I2C nodes to Tegra114 DT
NVIDIA's Tegra114 has 5 I2C controllers. These controllers have the
following changes which makes incompatible with previous hardware:
- Single clock source to I2C controller.
- Interrupt support for per packet transfer.
Add DT entry for I2C controllers and make it compatible with
"nvidia,tegra114-i2c".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed location of status property for consistency] Signed-off-by: Stephen Warren <swarren@nvidia.com>
Laxman Dewangan [Wed, 13 Mar 2013 19:49:50 +0000 (01:19 +0530)]
ARM: tegra: add APB DMA nodes to Tegra114 DT
NVIDIA's Tegra114 has 32 channels APB DMA controller. Add DT entry for
APB DMA controllers and make it compatible with "nvidia,tegra114-apbdma".
Tegra114 DMA controller is not compatible with Tegra30/Tegra20 DMA
controller driver as in Tegra114, the global pause also clock gate the
DMA register and hence it iw not possible to write the DMA register
with global pause.
Andrew Chew [Tue, 12 Mar 2013 23:40:51 +0000 (16:40 -0700)]
ARM: tegra: fix the status of PWM DT nodes
We should be defining the PWM nodes with status as "disabled" in the
chip-specific dtsi file, since we don't know whether specific boards
will use the PWM or not. This patch fixes the PWM node status for
Tegra20 and Tegra30.
Also fixed the one user of PWM, which is the Tegra20 medcom-wide board,
so that PWM is set to "okay" in the board-specific dts file.
Signed-off-by: Andrew Chew <achew@nvidia.com>
[swarren: in medcom-wide: fixed node sort order, removed duplicate pwm:
label, fixed syntax error] Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Thu, 4 Apr 2013 23:13:54 +0000 (17:13 -0600)]
clk: tegra: fix enum tegra114_clk to match binding
A gap exists in the binding's clock ID definitions. Fix the clock driver
to be consistent. This allows pclk to be looked up through device tree
and prevents:
ERROR: could not get clock /pmc:pclk(0)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The UART driver enables the console uart clock, so we don't need to do that
anymore in this file.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add references to tegra_car clocks for the basic device nodes. Also remove
the clock-frequency property of the serial node as the UART driver can now
use the clock framework to obtain the frequency.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
clk: tegra: devicetree match for nvidia,tegra114-car
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
The device tree binding models Tegra114 CAR (Clock And Reset) as a single
monolithic clock provider.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Workaround a hardware bug in MSENC during clock enable.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
We will need some tegra peripheral clocks with the CLK_IGNORE_UNUSED flag,
most notably mselect, which is a bridge between AXI and most peripherals.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
clk: tegra: Add new fields and PLL types for Tegra114
Tegra114 introduces new PLL types. This requires new clocktypes as well
as some new fields in the pll structure.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
clk: tegra: move from a lock bit idx to a lock mask
PLLC2 and PLLC3 on Tegra114 have separate phaselock and frequencylock bits.
So switch to a lock mask to be able to test both at the same time.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Some PLLs in Tegra114 don't use a power of 2 mapping for the post divider.
Introduce a table based approach and switch PLLU to it.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra114 PLLC2 and PLLC3 don't have a lock enable bit. The lock bits are
always functional.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Not all PLLs in Tegra114 have a bypass bit. Adapt the common code to only use
this bit when available.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Refactor the PLL programming code to make it useable by the new PLL types
introduced by Tegra114.
The following changes were done:
* Split programming the PLL into updating m,n,p and updating cpcon
* Move locking from _update_pll_cpcon() to clk_pll_set_rate()
* Introduce _get_pll_mnp() helper
* Move check for identical m,n,p values to clk_pll_set_rate()
* struct tegra_clk_pll_freq_table will always contain the values as defined
by the hardware.
* Simplify the arguments to clk_pll_wait_for_lock()
* Split _tegra_clk_register_pll()
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
tegra_boot_secondary() relies on some of the car ops. This means having an
uninitialized tegra_cpu_car_ops will lead to an early boot panic.
Providing a dummy struct avoids this and makes adding Tegra114 clock support
in a bisectable way a lot easier.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Mon, 25 Mar 2013 19:22:24 +0000 (13:22 -0600)]
clk: tegra: defer application of init table
The Tegra clock driver is initialized during the ARM machine descriptor's
.init_irq() hook. It can't be initialized earlier, since dynamic memory
usage is required. It can't be initialized later, since the .init_timer()
hook needs the clocks initialized. However, at this time, udelay()
doesn't work.
The Tegra clock initialization table may enable some PLLs. Enabling a PLL
may require usage of udelay(). Hence, this can't happen right when the
clock driver is initialized.
To solve this, separate the clock driver initialization from the clock
table processing, so they can execute at separate times.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Correct IDs for cdev1 and cdev2 are 94 and 93 respectively.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: split into separate driver and device-tree patches] Signed-off-by: Stephen Warren <swarren@nvidia.com>
clk: tegra: Make gr2d and gr3d clocks children of pll_c
By default these clocks are children of pll_m, but in downstream kernels
they are reparented to pll_c. While at it, decrease their frequencies to
300 MHz because the defaults aren't in the specified range.
gr2d can reportedly run at much higher frequencies, but 300 MHz works
and is a more conservative default.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Mike Turquette <mturquette@linaro.org> Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Thierry Reding [Thu, 28 Mar 2013 20:31:27 +0000 (21:31 +0100)]
clk: tegra: Export peripheral reset functions
The tegra_periph_reset_assert() and tegra_periph_reset_deassert()
functions can be used by drivers to reset peripherals. In order to allow
such drivers to be built as modules, export the functions.
Note that this restores the status quo as the functions were exported
before the move to the drivers/clk tree.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Yen Lin [Wed, 6 Mar 2013 11:47:24 +0000 (11:47 +0000)]
clk: tegra: Fix periph_clk_to_bit macro
The parameter name should be "gate", not "periph". This worked, however,
because it happens that everywhere periph_clk_to_bit is called, "gate" was
in the local scope.
Signed-off-by: Yen Lin <yelin@nvidia.com> Signed-off-by: Andrew Chew <achew@nvidia.com> Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de> Reviewed-by: Prashant Gaikwad <pgaikwad@nvidia.com> Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com> Acked-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Joseph Lo [Wed, 3 Apr 2013 11:31:46 +0000 (19:31 +0800)]
ARM: dt: tegra: add bindings of power management configurations for PMC
The PMC mostly controls the entry and exit of the system from different
sleep modes. Different platform or system may have different configurations.
The power management configurations of PMC is represented as some properties.
The system needs to define the properties when the system supports deep sleep
mode (i.e. suspend).
Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Rob Herring <rob.herring@calxeda.com> Cc: devicetree-discuss@lists.ozlabs.org Signed-off-by: Joseph Lo <josephl@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Joseph Lo [Wed, 3 Apr 2013 11:31:44 +0000 (19:31 +0800)]
gpio: tegra: add gpio wakeup source handling
This patch add the gpio wakeup source handling for the Tegra platform. It
was be done by enabling the irq for the gpio in the gpio controller and
enabling the bank irq of the gpio in the Tegra legacy irq controller when
the system going to suspend.
Based on the work by:
Varun Wadekar <vwadekar@nvidia.com>
Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Joseph Lo <josephl@nvidia.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Mike Turquette [Thu, 28 Mar 2013 20:59:02 +0000 (13:59 -0700)]
clk: allow reentrant calls into the clk framework
Reentrancy into the clock framework is necessary for clock operations
that result in nested calls to the clk api. A common example is a clock
that is prepared via an i2c transaction, such as a clock inside of a
discrete audio chip or a power management IC. The i2c subsystem itself
will use the clk api resulting in a deadlock:
The ability to reenter the clock framework prevents this deadlock.
Other use cases exist such as allowing .set_rate callbacks to call
clk_set_parent to achieve the best rate, or to save power in certain
configurations. Yet another example is performing pinctrl operations
from a clk_ops callback. Calls into the pinctrl subsystem may call
clk_{un}prepare on an unrelated clock. Allowing for nested calls to
reenter the clock framework enables both of these use cases.
Reentrancy is implemented by two global pointers that track the owner
currently holding a global lock. One pointer tracks the owner during
sleepable, mutex-protected operations and the other one tracks the owner
during non-interruptible, spinlock-protected operations.
When the clk framework is entered we try to hold the global lock. If it
is held we compare the current task against the current owner; a match
implies a nested call and we reenter. If the values do not match then
we block on the lock until it is released.
Signed-off-by: Mike Turquette <mturquette@linaro.org> Cc: Rajagopal Venkat <rajagopal.venkat@linaro.org> Cc: David Brown <davidb@codeaurora.org> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Mike Turquette [Thu, 28 Mar 2013 20:59:01 +0000 (13:59 -0700)]
clk: abstract locking out into helper functions
Create locking helpers for the global mutex and global spinlock. The
definitions of these helpers will be expanded upon in the next patch
which introduces reentrancy into the locking scheme.
Signed-off-by: Mike Turquette <mturquette@linaro.org> Cc: Rajagopal Venkat <rajagopal.venkat@linaro.org> Cc: David Brown <davidb@codeaurora.org> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Emilio López [Wed, 27 Mar 2013 02:39:17 +0000 (23:39 -0300)]
clk: sunxi: rename compatible strings
During the introduction of the Allwinner SoC platforms, sunxi was
initially meant as a generic name for all the variants of the Allwinner
SoC.
It was ok at the time of the support of only the A10 and A13 that
look pretty much the same; but it's beginning to be troublesome with
the future addition of the Allwinner A31 (sun6i) that is quite
different, and would introduce some weird logic, where sunxi would
actually mean in some case sun4i and sun5i but without sun6i...
Moreover, it makes the compatible strings naming scheme not consistent
with other architectures, where usually for this kind of compability, we
just use the oldest SoC name that has this IP, so let's do just this.
Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: Mike Turquette <mturquette@linaro.org>
Emilio López [Mon, 25 Feb 2013 14:44:26 +0000 (11:44 -0300)]
clk: arm: sunxi: Add a new clock driver for sunxi SOCs
This commit implements the base CPU clocks for sunxi devices. It has
been tested using a slightly modified cpufreq driver from the
linux-sunxi 3.0 tree.
Additionally, document the new bindings introduced by this patch.
Prashant Gaikwad [Wed, 20 Mar 2013 12:00:34 +0000 (17:30 +0530)]
clk: Add composite clock type
Not all clocks are required to be decomposed into basic clock
types but at the same time want to use the functionality
provided by these basic clock types instead of duplicating.
For example, Tegra SoC has ~100 clocks which can be decomposed
into Mux -> Div -> Gate clock types making the clock count to
~300. Also, parent change operation can not be performed on gate
clock which forces to use mux clock in driver if want to change
the parent.
Instead aggregate the basic clock types functionality into one
clock and just use this clock for all operations. This clock
type re-uses the functionality of basic clock types and not
limited to basic clock types but any hardware-specific
implementation.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes this time around. The iscsi-target CHAP
big-endian bugfix and bump FD_MAX_SECTORS=2048 default patch to allow
1MB sized I/Os for FILEIO backends on >= v3.5 code are both CC'ed to
stable.
Also, there is a persistent reservations regression that has recently
been reported for >= v3.8.x code, that is currently being tracked down
for v3.9."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/pscsi: Reject cross page boundary case in pscsi_map_sg
target/file: Bump FD_MAX_SECTORS to 2048 to handle 1M sized I/Os
tcm_vhost: Flush vhost_work in vhost_scsi_flush()
tcm_vhost: Add missed lock in vhost_scsi_clear_endpoint()
target: fix possible memory leak in core_tpg_register()
target/iscsi: Fix mutual CHAP auth on big-endian arches
target_core_sbc: use noop for SYNCHRONIZE_CACHE
Linus Torvalds [Sat, 23 Mar 2013 22:49:49 +0000 (15:49 -0700)]
Merge tag 'md-3.9-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"A few bugfixes for md
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable"
* tag 'md-3.9-fixes' of git://neil.brown.name/md:
md: remove CONFIG_MULTICORE_RAID456 entirely
md/raid5: ensure sync and DISCARD don't happen at the same time.
MD: Prevent sysfs operations on uninitialized kobjects
MD RAID5: Avoid accessing gendisk or queue structs when not available
md/raid5: schedule_construction should abort if nothing to do.
Linus Torvalds [Sat, 23 Mar 2013 19:33:36 +0000 (12:33 -0700)]
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata updates from Jeff Garzik:
"Simple stuff. See one-line summaries."
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_samsung_cf: use module_platform_driver_probe()
[libata] Avoid specialized TLA's in ZPODD's Kconfig
libata-acpi.c: fix copy and paste mistake in ata_acpi_register_power_resource
sata_fsl: Remove redundant NULL check before kfree
ahci: Add Device IDs for Intel Wellsburg PCH
ata_piix: Add MODULE_PARM_DESC to prefer_ms_hyperv
Linus Torvalds [Sat, 23 Mar 2013 19:32:14 +0000 (12:32 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"One bugfix for the tegra driver. Two updates regarding email
addresses and MAINTAINERS which I like to have up-to-date so people
can be reached immediately. While we are here, there is on PCI_ID
addition."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer entry for atmel i2c driver
i2c: Fix my e-mail address in drivers and documentation
i2c: iSMT: add Intel Avoton DeviceIDs
i2c: tegra: check the clk_prepare_enable() return value
Linus Torvalds [Sat, 23 Mar 2013 19:30:39 +0000 (12:30 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
"Fix a boot issues and correct the AcpiMmioSel bitmask in the
sp5100_tco watchdog device driver"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2
watchdog: sp5100_tco: Remove code that may cause a boot failure
Torsten Duwe [Sat, 23 Mar 2013 14:39:34 +0000 (15:39 +0100)]
KMS: fix EDID detailed timing frame rate
When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed. Consecutive (debug-) output of that mode thus yields 0 for
vsync. This simple fix also speeds up future invocations of
drm_mode_vrefresh().
While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.
Torsten Duwe [Sat, 23 Mar 2013 14:38:22 +0000 (15:38 +0100)]
KMS: fix EDID detailed timing vsync parsing
EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these. The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.
See
http://en.wikipedia.org/wiki/EDID
and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.
Pull NVMe driver update from Matthew Wilcox:
"These patches have mostly been baking for a few months; sorry I didn't
get them in during the merge window. They're all bug fixes, except
for the addition of the SMART log and the addition to MAINTAINERS."
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Add namespaces with no LBA range feature
MAINTAINERS: Add entry for the NVMe driver
NVMe: Initialize iod nents to 0
NVMe: Define SMART log
NVMe: Add result to nvme_get_features
NVMe: Set result from user admin command
NVMe: End queued bio requests when freeing queue
NVMe: Free cmdid on nvme_submit_bio error
Linus Torvalds [Fri, 22 Mar 2013 23:41:44 +0000 (16:41 -0700)]
Merge branch 'akpm' (fixes from Andrew)
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mqueue: sys_mq_open: do not call mnt_drop_write() if read-only
mm/hotplug: only free wait_table if it's allocated by vmalloc
dma-debug: update DMA debug API to better handle multiple mappings of a buffer
dma-debug: fix locking bug in check_unmap()
drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
drivers/rtc/rtc-da9052.c: fix for rtc device registration
mm: zone_end_pfn is too small
poweroff: change orderly_poweroff() to use schedule_work()
mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
printk: Provide a wake_up_klogd() off-case
irq_work.h: fix warning when CONFIG_IRQ_WORK=n
Vladimir Davydov [Fri, 22 Mar 2013 22:04:51 +0000 (15:04 -0700)]
mqueue: sys_mq_open: do not call mnt_drop_write() if read-only
mnt_drop_write() must be called only if mnt_want_write() succeeded,
otherwise the mnt_writers counter will diverge.
mnt_writers counters are used to check if remounting FS as read-only is
OK, so after an extra mnt_drop_write() call, it would be impossible to
remount mqueue FS as read-only. Besides, on umount a warning would be
printed like this one:
=====================================
[ BUG: bad unlock balance detected! ]
3.9.0-rc3 #5 Not tainted
-------------------------------------
a.out/12486 is trying to release lock (sb_writers) at:
mnt_drop_write+0x1f/0x30
but there are no more locks to release!
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com> Cc: Doug Ledford <dledford@redhat.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexander Duyck [Fri, 22 Mar 2013 22:04:49 +0000 (15:04 -0700)]
dma-debug: update DMA debug API to better handle multiple mappings of a buffer
There were reports of the igb driver unmapping buffers without calling
dma_mapping_error. On closer inspection issues were found in the DMA
debug API and how it handled multiple mappings of the same buffer.
The issue I found is the fact that the debug_dma_mapping_error would
only set the map_err_type to MAP_ERR_CHECKED in the case that the was
only one match for device and device address. However in the case of
non-IOMMU, multiple addresses existed and as a result it was not setting
this field once a second mapping was instantiated. I have resolved this
by changing the search so that it instead will now set MAP_ERR_CHECKED
on the first buffer that matches the device and DMA address that is
currently in the state MAP_ERR_NOT_CHECKED.
A secondary side effect of this patch is that in the case of multiple
buffers using the same address only the last mapping will have a valid
map_err_type. The previous mappings will all end up with map_err_type
set to MAP_ERR_CHECKED because of the dma_mapping_error call in
debug_dma_map_page. However this behavior may be preferable as it means
you will likely only see one real error per multi-mapped buffer, versus
the current behavior of multiple false errors mer multi-mapped buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Cc: Joerg Roedel <joro@8bytes.org> Reviewed-by: Shuah Khan <shuah.khan@hp.com> Tested-by: Shuah Khan <shuah.khan@hp.com> Cc: Jakub Kicinski <kubakici@wp.pl> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexander Duyck [Fri, 22 Mar 2013 22:04:48 +0000 (15:04 -0700)]
dma-debug: fix locking bug in check_unmap()
In check_unmap() it is possible to get into a dead-locked state if
dma_mapping_error is called. The problem is that the bucket is locked in
check_unmap, and locked again by debug_dma_mapping_error which is called
by dma_mapping_error. To resolve that we must release the lock on the
bucket before making the call to dma_mapping_error.
[akpm@linux-foundation.org: restore 80-col trickery to be consistent with the rest of the file] Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Cc: Joerg Roedel <joro@8bytes.org> Reviewed-by: Shuah Khan <shuah.khan@hp.com> Tested-by: Shuah Khan <shuah.khan@hp.com> Cc: Jakub Kicinski <kubakici@wp.pl> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicolas Ferre [Fri, 22 Mar 2013 22:04:47 +0000 (15:04 -0700)]
drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
On some revisions of AT91 SoCs, the RTC IMR register is not working.
Instead of elaborating a workaround for that specific SoC or IP version,
we simply use a software variable to store the Interrupt Mask Register
and modify it for each enabling/disabling of an interrupt. The overhead
of this is negligible anyway.
The interrupt mask register (IMR) for the RTC is broken on the AT91SAM9x5
sub-family of SoCs (good overview of the members here:
http://www.eewiki.net/display/linuxonarm/AT91SAM9x5 ). The "user visible
effect" is the RTC doesn't work.
That sub-family is less than two years old and only has devicetree (DT)
support and came online circa lk 3.7 . The dust is yet to settle on the
DT stuff at least for AT91 SoCs (translation: lots of stuff is still
broken, so much that it is hard to know where to start).
The fix in the patch is pretty simple: just shadow the silicon IMR
register with a variable in the driver. Some older SoCs (pre-DT) use the
the rtc-at91rm9200 driver (e.g. obviously the AT91RM9200) and they should
not be impacted by the change. There shouldn't be a large volume of
interrupts associated with a RTC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Reported-by: Douglas Gilbert <dgilbert@interlog.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
Commit be8678149701 ("drivers/video/ep93xx-fb.c: use devm_ functions")
introduced a build error:
drivers/video/ep93xx-fb.c: In function 'ep93xxfb_probe':
drivers/video/ep93xx-fb.c:532: error: implicit declaration of function 'devm_ioremap'
drivers/video/ep93xx-fb.c:533: warning: assignment makes pointer from integer without a cast
Include <linux/io.h> to pickup the declaration of 'devm_ioremap'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Acked-by: Ryan Mallon <rmallon@gmail.com> Cc: Damien Cassou <damien.cassou@lifl.fr> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Fri, 22 Mar 2013 22:04:41 +0000 (15:04 -0700)]
poweroff: change orderly_poweroff() to use schedule_work()
David said:
Commit 6c0c0d4d1080 ("poweroff: fix bug in orderly_poweroff()")
apparently fixes one bug in orderly_poweroff(), but introduces
another. The comments on orderly_poweroff() claim it can be called
from any context - and indeed we call it from interrupt context in
arch/powerpc/platforms/pseries/ras.c for example. But since that
commit this is no longer safe, since call_usermodehelper_fns() is not
safe in interrupt context without the UMH_NO_WAIT option.
orderly_poweroff() can be used from any context but UMH_WAIT_EXEC is
sleepable. Move the "force" logic into __orderly_poweroff() and change
orderly_poweroff() to use the global poweroff_work which simply calls
__orderly_poweroff().
While at it, remove the unneeded "int argc" and change argv_split() to
use GFP_KERNEL.
We use the global "bool poweroff_force" to pass the argument, this can
obviously affect the previous request if it is pending/running. So we
only allow the "false => true" transition assuming that the pending
"true" should succeed anyway. If schedule_work() fails after that we
know that work->func() was not called yet, it must see the new value.
This means that orderly_poweroff() becomes async even if we do not run
the command and always succeeds, schedule_work() can only fail if the
work is already pending. We can export __orderly_poweroff() and change
the non-atomic callers which want the old semantics.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reported-by: David Gibson <david@gibson.dropbear.id.au> Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi> Cc: Feng Hong <hongfeng@marvell.com> Cc: Kees Cook <keescook@chromium.org> Cc: Serge Hallyn <serge.hallyn@canonical.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wanpeng Li [Fri, 22 Mar 2013 22:04:40 +0000 (15:04 -0700)]
mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
hugetlb_total_pages is used for overcommit calculations but the current
implementation considers only the default hugetlb page size (which is
either the first defined hugepage size or the one specified by
default_hugepagesz kernel boot parameter).
If the system is configured for more than one hugepage size, which is
possible since commit a137e1cc6d6e ("hugetlbfs: per mount huge page
sizes") then the overcommit estimation done by __vm_enough_memory()
(resp. shown by meminfo_proc_show) is not precise - there is an
impression of more available/allowed memory. This can lead to an
unexpected ENOMEM/EFAULT resp. SIGSEGV when memory is accounted.
Testcase:
boot: hugepagesz=1G hugepages=1
the default overcommit ratio is 50
before patch:
wake_up_klogd() is useless when CONFIG_PRINTK=n because neither printk()
nor printk_sched() are in use and there are actually no waiter on
log_wait waitqueue. It should be a stub in this case for users like
bust_spinlocks().
Otherwise this results in this warning when CONFIG_PRINTK=n and
CONFIG_IRQ_WORK=n:
kernel/built-in.o In function `wake_up_klogd':
(.text.wake_up_klogd+0xb4): undefined reference to `irq_work_queue'
To fix this, provide an off-case for wake_up_klogd() when
CONFIG_PRINTK=n.
There is much more from console_unlock() and other console related code
in printk.c that should be moved under CONFIG_PRINTK. But for now,
focus on a minimal fix as we passed the merged window already.
[akpm@linux-foundation.org: include printk.h in bust_spinlocks.c] Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Reported-by: James Hogan <james.hogan@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takahisa Tanaka [Sun, 3 Mar 2013 05:48:00 +0000 (14:48 +0900)]
watchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2
The AcpiMmioSel bit is bit 1 in the AcpiMmioEn register, but the current
sp5100_tco driver is using bit 2.
See 2.3.3 Power Management (PM) Registers page 150 of the
AMD SB800-Series Southbridges Register Reference Guide [1].
AcpiMmioEn - RW – 8/16/32 bits - [PM_Reg: 24h]
Field Name Bits Default Description
AcpiMMioDecodeEn 0 0b Set to 1 to enable AcpiMMio space.
AcpiMMIoSel 1 0b Set AcpiMMio registers to be memory-mapped or IO-mapped space.
0: Memory-mapped space
1: I/O-mapped space
The sp5100_tco driver expects zero as a value of AcpiMmioSel (bit 1).
Fortunately, no problems were caused by this typo, because the default
value of the undocumented misused bit 2 seems to be zero.
However, the sp5100_tco driver should use the correct bitmask value.
Takahisa Tanaka [Sun, 3 Mar 2013 05:52:07 +0000 (14:52 +0900)]
watchdog: sp5100_tco: Remove code that may cause a boot failure
A problem was found on PC's with the SB700 chipset: The PC fails to
load BIOS after running the 3.8.x kernel until the power is completely
cut off. It occurs in all 3.8.x versions and the mainline version as of
2/4. The issue does not occur with the 3.7.x builds.
There are two methods for accessing the watchdog registers.
1. Re-programming a resource address obtained by allocate_resource()
to chipset.
2. Use the direct memory-mapped IO access.
The method 1 can be used by all the chipsets (SP5100, SB7x0, SB8x0 or
later). However, experience shows that only PC with the SB8x0 (or
later) chipsets can use the method 2.
This patch removes the method 1, because the critical problem was found.
That's why the watchdog timer was able to be used on SP5100 and SB7x0
chipsets until now.
Add a table lookup feature to the mux clock. Also allow arbitrary masks
instead of the width. This will be used by some clocks on Tegra114. Also
adapt the tegra periph clk because it uses struct clk_mux directly.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
Sachin Kamat [Wed, 13 Mar 2013 09:47:49 +0000 (15:17 +0530)]
clk: Fix incorrect return type in clk.c
Return type of function clk_propagate_rate_change is a pointer.
But 0 was being returned. Change it to NULL.
Silences the following warning:
drivers/clk/clk.c:977:24: warning: Using plain integer as NULL pointer
Wei Yongjun [Mon, 11 Mar 2013 15:55:18 +0000 (23:55 +0800)]
clk: prima2: fix return value check in sirfsoc_of_clk_init()
In case of error, the function clk_get() returns ERR_PTR()
not NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: Barry Song <21cnbao@gmail.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: added missing parenthesis to fix compile break]
Linus Torvalds [Fri, 22 Mar 2013 19:45:08 +0000 (12:45 -0700)]
Merge tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Mostly HD-audio and USB-audio regression fixes:
- Oops fix at unloading of snd-hda-codec-conexant module
- A few trivial regression fixes for Cirrus and Conexant HD-audio
codecs
- Relax the USB-audio descriptor parse errors as non-fatal
- Fix locking of HD-audio CA0132 DSP loader
- Fix the generic HD-audio parser for VIA codecs"
* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix DAC assignment for independent HP
ALSA: hda - Fix abuse of snd_hda_lock_devices() for DSP loader
ALSA: hda - Fix typo in checking IEC958 emphasis bit
ALSA: snd-usb: mixer: ignore -EINVAL in snd_usb_mixer_controls()
ALSA: snd-usb: mixer: propagate errors up the call chain
ALSA: usb: Parse UAC2 extension unit like for UAC1
ALSA: hda - Fix yet missing GPIO/EAPD setup in cirrus driver
ALSA: hda/cirrus - Fix the digital beep registration
ALSA: hda - Fix missing beep detach in patch_conexant.c
ALSA: documentation: Fix typo in Documentation/sound
Linus Torvalds [Fri, 22 Mar 2013 19:44:22 +0000 (12:44 -0700)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fixes from Borislav Petkov:
"A fix from Mauro to correct csrow size accounting in sysfs and a
sparse fix from Stephen Hemminger."
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Merge mci.mem_is_per_rank with mci.csbased
amd64_edac: Correct DIMM sizes
EDAC: Make sysfs functions static
Keith Busch [Thu, 31 Jan 2013 21:40:38 +0000 (14:40 -0700)]
NVMe: Add namespaces with no LBA range feature
The LBA Range Type feature is optional in the NVMe specification,
so we should continue with adding namespaces for controllers that do
not implement this feature.
Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Linus Torvalds [Fri, 22 Mar 2013 18:44:04 +0000 (11:44 -0700)]
vfs,proc: guarantee unique inodes in /proc
Dave Jones found another /proc issue with his Trinity tool: thanks to
the namespace model, we can have multiple /proc dentries that point to
the same inode, aliasing directories in /proc/<pid>/net/ for example.
This ends up being a total disaster, because it acts like hardlinked
directories, and causes locking problems. We rely on the topological
sort of the inodes pointed to by dentries, and if we have aliased
directories, that odering becomes unreliable.
In short: don't do this. Multiple dentries with the same (directory)
inode is just a bad idea, and the namespace code should never have
exposed things this way. But we're kind of stuck with it.
This solves things by just always allocating a new inode during /proc
dentry lookup, instead of using "iget_locked()" to look up existing
inodes by superblock and number. That actually simplies the code a bit,
at the cost of potentially doing more inode [de]allocations.
That said, the inode lookup wasn't free either (and did a lot of locking
of inodes), so it is probably not that noticeable. We could easily keep
the old lookup model for non-directory entries, but rather than try to
be excessively clever this just implements the minimal and simplest
workaround for the problem.
Reported-and-tested-by: Dave Jones <davej@redhat.com> Analyzed-by: Al Viro <viro@zeniv.linux.org.uk> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Laxman Dewangan [Fri, 15 Mar 2013 05:34:08 +0000 (05:34 +0000)]
i2c: tegra: check the clk_prepare_enable() return value
NVIDIA's Tegra SoC allows read/write of controller register only
if controller clock is enabled. System hangs if read/write happens
to registers without enabling clock.
clk_prepare_enable() can be fail due to unknown reason and hence
adding check for return value of this function. If this function
success then only access register otherwise return to caller with
error.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Linus Torvalds [Fri, 22 Mar 2013 00:59:22 +0000 (17:59 -0700)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French:
"Three small CIFS Fixes (the most important of the three fixes a recent
problem authenticating to Windows 8 using cifs rather than SMB2)"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs: ignore everything in SPNEGO blob after mechTypes
cifs: delay super block destruction until all cifsFileInfo objects are gone
cifs: map NT_STATUS_SHARING_VIOLATION to EBUSY instead of ETXTBSY
Linus Torvalds [Fri, 22 Mar 2013 00:56:10 +0000 (17:56 -0700)]
Merge tag 'ext4_for_linue' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix a number of regression and other bugs in ext4, most of which were
relatively obscure cornercases or races that were found using
regression tests."
* tag 'ext4_for_linue' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (21 commits)
ext4: fix data=journal fast mount/umount hang
ext4: fix ext4_evict_inode() racing against workqueue processing code
ext4: fix memory leakage in mext_check_coverage
ext4: use s_extent_max_zeroout_kb value as number of kb
ext4: use atomic64_t for the per-flexbg free_clusters count
jbd2: fix use after free in jbd2_journal_dirty_metadata()
ext4: reserve metadata block for every delayed write
ext4: update reserved space after the 'correction'
ext4: do not use yield()
ext4: remove unused variable in ext4_free_blocks()
ext4: fix WARN_ON from ext4_releasepage()
ext4: fix the wrong number of the allocated blocks in ext4_split_extent()
ext4: update extent status tree after an extent is zeroed out
ext4: fix wrong m_len value after unwritten extent conversion
ext4: add self-testing infrastructure to do a sanity check
ext4: avoid a potential overflow in ext4_es_can_be_merged()
ext4: invalidate extent status tree during extent migration
ext4: remove unnecessary wait for extent conversion in ext4_fallocate()
ext4: add warning to ext4_convert_unwritten_extents_endio
ext4: disable merging of uninitialized extents
...
Johan Hovold [Tue, 19 Mar 2013 08:21:15 +0000 (09:21 +0100)]
USB: ftdi_sio: fix use-after-free in TIOCMIWAIT
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
When switching to tty ports, some lifetime assumptions were changed.
Specifically, close can now be called before the final tty reference is
dropped as part of hangup at device disconnect. Even with the ftdi
private-data refcounting this means that the port private data can be
freed while a process is sleeping on modem-status changes and thus
cannot be relied on to detect disconnects when woken up.