Matt Redfearn [Thu, 31 Mar 2016 09:05:41 +0000 (10:05 +0100)]
MIPS: Kernel: Implement KASLR using CONFIG_RELOCATABLE
This patch adds KASLR to the MIPS kernel.
Entropy is derived from the banner, which will change every build and
random_get_entropy() which should provide additional runtime entropy.
Additionally the bootloader may pass entropy via the /chosen/kaslr-seed
node in device tree.
The kernel is relocated by up to RANDOMIZE_BASE_MAX_OFFSET bytes from
its link address (PHYSICAL_START). Because relocation happens so early
in the kernel boot, the amount of physical memory has not yet been
determined. This means the only way to limit relocation within the
available memory is via Kconfig.
Matt Redfearn [Thu, 31 Mar 2016 09:05:40 +0000 (10:05 +0100)]
MIPS: Introduce plat_get_fdt a platform API to retrieve the FDT
Early access to the kernel command line requires early access to the FDT
for platforms which pass the command line within the device tree. There
was no common way to retrieve the location of the FDT without incurring
side effects, such as plat_mem_setup which, on Malta at least,
initializes a bunch of other stuff.
This patch adds plat_get_ftd() for IMG platforms.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: kernel-hardening@lists.openwall.com Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12988/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Thu, 31 Mar 2016 09:05:39 +0000 (10:05 +0100)]
MIPS: Add CONFIG_RELOCATABLE Kconfig option
Add option to KConfig to enable the kernel to relocate itself at
runtime.
Relocation is supported R2 and later of the MIPS architecture, 32bit
and 64bit. The platform is also required to provide support through
plat_get_fdt() added in a later patch.
Matt Redfearn [Thu, 31 Mar 2016 09:05:38 +0000 (10:05 +0100)]
MIPS: bootmem: When relocatable, free memory below kernel
The kernel reserves all memory before the _end symbol as bootmem,
however, once the kernel can be relocated elsewhere in memory this may
result in a large amount of wasted memory. The assumption is that the
memory between the link and relocated address of the kernel may be
released back to the available memory pool.
Memory statistics for a Malta with the kernel relocating by
16Mb, without the patch:
Memory: 105952K/131072K available (4604K kernel code, 242K rwdata,
892K rodata, 1280K init, 183K bss, 25120K reserved, 0K cma-reserved)
And with the patch:
Memory: 122336K/131072K available (4604K kernel code, 242K rwdata,
892K rodata, 1280K init, 183K bss, 8736K reserved, 0K cma-reserved)
The 16Mb offset is removed from the reserved region and added back to
the available region.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Aaro Koskinen <aaro.koskinen@nokia.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com> Cc: Jaedon Shin <jaedon.shin@gmail.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: kernel-hardening@lists.openwall.com Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12986/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Thu, 31 Mar 2016 09:05:37 +0000 (10:05 +0100)]
MIPS: Call relocate_kernel if CONFIG_RELOCATABLE=y
If CONFIG_RELOCATABLE is enabled, call relocate_kernel.
This function will return the entry point of the relocated kernel if
copy/relocate is sucessful or the original entry point if not. The stack
pointer must then be pointed into the new image.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: linux-mips@linux-mips.org Cc: kernel-hardening@lists.openwall.com Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12984/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Thu, 31 Mar 2016 09:05:36 +0000 (10:05 +0100)]
MIPS: Kernel: Add relocate.c
arch/mips/kernel/relocate.c contains the functions necessary to relocate
the kernel elsewhere in memory
The kernel makes a copy of itself at the new address. It uses the
relocation table inserted by the relocs tool to fix symbol references
within the new image.
If copy/relocation is sucessful then the entry point of the new kernel
is returned, otherwise fall back to starting the kernel in place.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: kernel-hardening@lists.openwall.com Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12985/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Thu, 31 Mar 2016 09:05:35 +0000 (10:05 +0100)]
MIPS: Generate relocation table when CONFIG_RELOCATABLE
When CONFIG_RELOCATABLE is enabled (added in later patch) add
--emit-relocs to vmlinux LDFLAGS so that fully linked vmlinux contains
relocation information.
Run the previously added relocs tool to fill in the .data.relocs section
of vmlinux with a table of relocations. The relocs tool will also remove
(mark as 0 length) the relocation sections added to vmlinux.
When vmlinux is passed to the boot makefile for conversion into a boot
image the now empty relocation sections will be removed and the
populated relocation table will be included in the binary image.
Matt Redfearn [Thu, 31 Mar 2016 09:05:34 +0000 (10:05 +0100)]
MIPS: Reserve space for relocation table
When CONFIG_RELOCATABLE is enabled, add a new section in the memory map
to be filled with relocation data.
CONFIG_RELOCATION_TABLE_SIZE allows the amount of space reserved to be
adjusted if necessary.
The relocs tool will populate this reserved space with relocation
information. The space is reserved within the elf by filling it with
0's, and an invalid entry is left at the start of the space such that
kernel relocation will be aborted if the table is empty.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Aaro Koskinen <aaro.koskinen@nokia.com> Cc: David Daney <ddaney@caviumnetworks.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: linux-mips@linux-mips.org Cc: kernel-hardening@lists.openwall.com Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12982/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Thu, 31 Mar 2016 09:05:32 +0000 (10:05 +0100)]
MIPS: tools: Add relocs tool
This tool is based on the x86/boot/tools/relocs tool.
It parses the relocations present in the vmlinux elf file, building a
table of relocations that will be necessary to run the kernel from an
address other than its link address. This table is inserted into the
vmlinux elf, in the .data.relocs section. The table is subsequently used
by the code in arch/mips/kernel/relocate.c (added later) to relocate the
kernel.
The tool, by default, also marks all relocation sections as 0 length.
This is due to objcopy currently being unable to handle copying the
relocations between 64 and 32 bit elf files as is done when building a
64 bit kernel.
Matt Redfearn [Tue, 29 Mar 2016 08:35:33 +0000 (09:35 +0100)]
MIPS: seccomp: Support compat with both O32 and N32
Previously the seccomp would only support strict mode on O32 userland
programs when the kernel had support for both O32 and N32 ABIs. Remove
kludge and support both ABIs.
With this patch in place, the seccomp_bpf self test now passes
global.mode_strict_support with N32 userland.
Suggested-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Acked-by: Kees Cook <keescook@chromium.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12917/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Tue, 29 Mar 2016 08:35:31 +0000 (09:35 +0100)]
MIPS: scall: Handle seccomp filters which redirect syscalls
Commit d218af78492a ("MIPS: scall: Always run the seccomp syscall
filters") modified the syscall code to always call the seccomp filters,
but missed the case where a filter may redirect the syscall, as
revealed by the seccomp_bpf self test.
The syscall path now restores the syscall from the stack after the
filter rather than saving it locally. Syscall number checking and
syscall function table lookup is done after the filter may have run such
that redirected syscalls are also checked, and executed.
The regular path of syscall number checking and pointer lookup is also
made more consistent between ABIs with scall64-64.S being the reference.
With this patch in place, the seccomp_bpf self test now passes
TRACE_syscall.syscall_redirected and TRACE_syscall.syscall_dropped on
all MIPS ABIs.
Fixes: d218af78492a ("MIPS: scall: Always run the seccomp syscall filters") Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Acked-by: Kees Cook <keescook@chromium.org> Cc: Eric B Munson <emunson@akamai.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-mips@linux-mips.org Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12916/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Tue, 29 Mar 2016 08:35:30 +0000 (09:35 +0100)]
MIPS: Support sending SIG_SYS to 32bit userspace from 64bit kernel
The seccomp_bpf self test revealed that a 64bit kernel delivered an
invalid SIG_SYS to a 32bit userspace, because it was falling into the
default of the switch statement. Add a case to handle delivering the
signal.
With this patch, the seccomp_bpf self test now passes the TRAP.handler
case with O32 and N32 userlands.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Acked-by: Kees Cook <keescook@chromium.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Amanieu d'Antras <amanieu@gmail.com> Cc: Alex Smith <alex.smith@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-mips@linux-mips.org Cc: IMG-MIPSLinuxKerneldevelopers@imgtec.com Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12915/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Tue, 29 Mar 2016 08:35:29 +0000 (09:35 +0100)]
selftests/seccomp: add MIPS self-test support
This adds self-test support on MIPS, based on RFC patch from Kees Cook.
Modifications from the RFC:
- support the O32 syscall which passes the real syscall number in a0.
- Use PTRACE_{GET,SET}REGS
- Because SYSCALL_NUM and SYSCALL_RET are the same register, it is not
possible to test modifying the syscall return value when skipping,
since both would need to set the same register. Therefore modify that
test case to just detect the skipped test.
Tested on MIPS32r2 / MIPS64r2 with O32, N32 and N64 userlands.
Daniel Wagner [Thu, 11 Feb 2016 12:36:54 +0000 (13:36 +0100)]
crash_dump: Add vmcore_elf32_check_arch
parse_crash_elf{32|64}_headers will check the headers via the
elf_check_arch respectively vmcore_elf64_check_arch macro.
The MIPS architecture implements those two macros differently.
In order to make the differentiation more explicit, let's introduce
an vmcore_elf32_check_arch to allow the archs to overwrite it.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de> Suggested-by: Maciej W. Rozycki <macro@imgtec.com> Reviewed-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12535/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simon Arlott [Wed, 9 Dec 2015 20:27:09 +0000 (20:27 +0000)]
irqchip: Add brcm, bcm6345-l1-intc device tree binding
Add device tree binding for the BCM6345 interrupt controller.
This controller is similar to the SMP-capable BCM7038 and
the BCM3380 but with packed interrupt registers.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Acked-by: Rob Herring <robh@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org> Cc: devicetree@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11804/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Tue, 1 Mar 2016 02:37:59 +0000 (02:37 +0000)]
MIPS: Sync icache & dcache in set_pte_at
It's possible for pages to become visible prior to update_mmu_cache
running if a thread within the same address space preempts the current
thread or runs simultaneously on another CPU. That is, the following
scenario is possible:
CPU0 CPU1
write to page
flush_dcache_page
flush_icache_page
set_pte_at
map page
update_mmu_cache
If CPU1 maps the page in between CPU0's set_pte_at, which marks it valid
& visible, and update_mmu_cache where the dcache flush occurs then CPU1s
icache will fill from stale data (unless it fills from the dcache, in
which case all is good, but most MIPS CPUs don't have this property).
Commit 4d46a67a3eb8 ("MIPS: Fix race condition in lazy cache flushing.")
attempted to fix that by performing the dcache flush in
flush_icache_page such that it occurs before the set_pte_at call makes
the page visible. However it has the problem that not all code that
writes to pages exposed to userland call flush_icache_page. There are
many callers of set_pte_at under mm/ and only 2 of them do call
flush_icache_page. Thus the race window between a page becoming visible
& being coherent between the icache & dcache remains open in some cases.
To illustrate some of the cases, a WARN was added to __update_cache with
this patch applied that triggered in cases where a page about to be
flushed from the dcache was not the last page provided to
flush_icache_page. That is, backtraces were obtained for cases in which
the race window is left open without this patch. The 2 standout examples
follow.
These code paths write into a page, call flush_dcache_page then call
set_pte_at without flush_icache_page inbetween. The end result is that
the icache can become corrupted & userland processes may execute
unexpected or invalid code, typically resulting in a reserved
instruction exception, a trap or a segfault.
Fix this race condition fully by performing any cache maintenance
required to keep the icache & dcache in sync in set_pte_at, before the
page is made valid. This has the added bonus of ensuring the cache
maintenance always happens in one location, rather than being duplicated
in flush_icache_page & update_mmu_cache. It also matches the way other
architectures solve the same problem (see arm, ia64 & powerpc).
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reported-by: Ionela Voinescu <ionela.voinescu@imgtec.com> Cc: Lars Persson <lars.persson@axis.com> Fixes: 4d46a67a3eb8 ("MIPS: Fix race condition in lazy cache flushing.") Cc: Steven J. Hill <sjhill@realitydiluted.com> Cc: David Daney <david.daney@cavium.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: stable <stable@vger.kernel.org> # v4.1+
Patchwork: https://patchwork.linux-mips.org/patch/12722/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Tue, 1 Mar 2016 02:37:58 +0000 (02:37 +0000)]
MIPS: Handle highmem pages in __update_cache
The following patch will expose __update_cache to highmem pages. Handle
them by mapping them in for the duration of the cache maintenance, just
like in __flush_dcache_page. The code for that isn't shared because we
need the page address in __update_cache so sharing became messy. Given
that the entirity is an extra 5 lines, just duplicate it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Lars Persson <lars.persson@axis.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: stable <stable@vger.kernel.org> # v4.1+
Patchwork: https://patchwork.linux-mips.org/patch/12721/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Tue, 1 Mar 2016 02:37:57 +0000 (02:37 +0000)]
MIPS: Flush highmem pages in __flush_dcache_page
When flush_dcache_page is called on an executable page, that page is
about to be provided to userland & we can presume that the icache
contains no valid entries for its address range. However if the icache
does not fill from the dcache then we cannot presume that the pages
content has been written back as far as the memories that the dcache
will fill from (ie. L2 or further out).
This was being done for lowmem pages, but not for highmem which can lead
to icache corruption. Fix this by mapping highmem pages & flushing their
content from the dcache in __flush_dcache_page before providing the page
to userland, just as is done for lowmem pages.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Lars Persson <lars.persson@axis.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12720/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Tue, 1 Mar 2016 02:37:56 +0000 (02:37 +0000)]
MIPS: Flush dcache for flush_kernel_dcache_page
The flush_kernel_dcache_page function was previously essentially a nop.
This is incorrect for MIPS, where if a page has been modified & either
it aliases or it's executable & the icache doesn't fill from dcache then
the content needs to be written back from dcache to the next level of
the cache hierarchy (which is shared with the icache).
Implement this by simply calling flush_dcache_page, treating this
kmapped cache flush function (flush_kernel_dcache_page) exactly the same
as its non-kmapped counterpart (flush_dcache_page).
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Lars Persson <lars.persson@axis.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12719/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Wed, 13 May 2015 15:17:14 +0000 (16:17 +0100)]
MIPS: cpu: Convert MIPS_CPU_* defs to (1ull << x)
The MIPS_CPU_* definitions have now filled the first 32-bits, and are
getting longer since they're written in hex without zero padding. Adding
my 8 extra MIPS_CPU_* definitions which I haven't upstreamed yet this is
getting increasingly ugly as the comments get shifted progressively to
the right. Its also error prone, and I've seen this cause mistakes on 3
separate occasions now, not helped by it being a conflict hotspot.
Convert all the MIPS_CPU_* definitions to the form (1ull << x). Humans
are better at incrementing than shifting.
Port the stblinux-3.3 code to perform a bunch of CPU-specific initialization,
make it compatible with run-time detection of the CPU, and unroll the
brcmstb-specific macros: BDEV_RB(), BDEV_UNSET.
The "pref 30" disabling is done as a quirk. This is a preliminary change to
allow the use of the "rotr" instruction gated by cpu_has_rixi.
Florian Fainelli [Sun, 31 Jan 2016 20:29:27 +0000 (12:29 -0800)]
BUS: brcmstb_gisb: Hook to MIPS board_be_handler
MIPS kernels allow platforms to invoke a custom Bus Error handler, add the
necessary code to do this for Broadcom SoCs where the GISB bus error handler can be used.
We may get a bus error from an address decoded outside of the GISB bus space,
so we need to check the validity of such a capture before printing anything.
Paul Burton [Thu, 4 Feb 2016 13:05:05 +0000 (13:05 +0000)]
MIPS: Support R_MIPS_PC{16,21,26} rel-style relocs
MIPS32 code uses rel-style relocs, and MIPS32r6 modules may include
R_MIPS_PC16, R_MIPS_PC21 & R_MIPS_PC26 relocations. We thus need to
support these relocations in order to load MIPS32r6 kernel modules. This
patch adds such support, which is similar to the rela-style support in
module-rela.c but making use of the implicit addend from the instruction
encoding.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Steven J. Hill <sjhill@realitydiluted.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12435/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Thu, 4 Feb 2016 13:05:04 +0000 (13:05 +0000)]
MIPS: Support R_MIPS_PC{21,26} rela-style relocs
MIPS64 code uses rela-style relocs, and MIPS64r6 modules may include the
new R_MIPS_PC21 & R_MIPS_PC26 relocations. We thus need to support these
relocations in order to load MIPS64r6 kernel modules. They are similar
to the existing R_MIPS_PC16 relocation but applying to a wider field.
Implement support for them by genericising the existing R_MIPS_PC16
implementation such that it can be used for different field widths, and
calling it for all 3 reloc types.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: Kees Cook <keescook@chromium.org> Cc: James Hogan <james.hogan@imgtec.com> Cc: Alex Smith <alex.smith@imgtec.com> Cc: Steven J. Hill <sjhill@realitydiluted.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12434/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Wed, 3 Feb 2016 12:06:35 +0000 (12:06 +0000)]
MIPS: SEAD3 can support MIPS32r6 CPUs
There are CPUs/bitfiles available for use with SEAD3 boards which
implement release 6 of the MIPS architecture. Allow building the kernel
for such a system.
Paul Burton [Wed, 3 Feb 2016 03:15:35 +0000 (03:15 +0000)]
MIPS: smp-cps: Stop printing EJTAG exceptions to UART
When CONFIG_MIPS_CPS_NS16550 is enabled, some register state is dumped
to the UART when an exception is taken via the BEV on secondary cores.
EJTAG exceptions are architecturally expected to be handled by the BEV
even when Status.BEV is 0. This effectively means that if userland
executes an sdbbp instruction on a secondary core then the kernel dumps
register state to the UART even though the exception is perfectly normal
& expected. Prevent this by simply not dumping information to the UART
for EJTAG exceptions.
Fixes: 609cf6f2291a ("MIPS: CPS: Early debug using an ns16550-compatible UART") Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12341/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Wed, 3 Feb 2016 03:15:34 +0000 (03:15 +0000)]
MIPS: smp-cps: Add nothreads kernel parameter
When debugging a new system or core it can be useful to disable the use
of multithreading. Introduce a "nothreads" kernel command line parameter
that can be set in order to do so.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Niklas Cassel <niklas.cassel@axis.com> Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12340/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Wed, 3 Feb 2016 03:15:33 +0000 (03:15 +0000)]
MIPS: smp-cps: Support MIPSr6 Virtual Processors
Introduce support for bringing up Virtual Processors in MIPSr6 systems
as CPUs, much like their VPE parallel from the now-deprecated MT ASE.
The existing mips_cps_boot_vpes function fits the MIPSr6 architecture
pretty well - it can now simply write the mask of running VPs to the
VC_RUN register, rather than looping through each & starting or stopping
as appropriate as is done for VPEs from the MT ASE. Thus the VP support
is in general an extension & simplification of the existing MT ASE VPE
(aka SMVP) support.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: Niklas Cassel <niklas.cassel@axis.com> Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12339/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Wed, 3 Feb 2016 03:15:32 +0000 (03:15 +0000)]
MIPS: smp-cps: Skip core setup if coherent
In preparation for supporting MIPSr6 multithreading (ie. VPs) which will
begin execution from the core reset vector, skip core level setup if the
core is already coherent. This is never the case when a core is first
started, since boot_core explicitly clears the cores GCR_Cx_COH_EN
register, and always the case when secondary VPs start since the first
VP to start will have enabled coherence after initialising the core &
its caches.
One notable side effect of this patch is that eva_init gets called
slightly earlier, prior to mips_cps_core_init rather than after it.
Paul Burton [Wed, 3 Feb 2016 03:15:31 +0000 (03:15 +0000)]
MIPS: smp-cps: Pull boot config retrieval out of mips_cps_boot_vpes
The mips_cps_boot_vpes function previously included code to retrieve
pointers to the core & VPE boot configuration structs. These structures
were used both by mips_cps_boot_vpes and by its mips_cps_core_entry
callsite. In preparation for skipping the call to mips_cps_boot_vpes on
some invocations of mips_cps_core_entry, pull the calculation of those
pointers out into a separate function such that it can continue to be
shared.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Niklas Cassel <niklas.cassel@axis.com> Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12337/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Wed, 3 Feb 2016 03:15:30 +0000 (03:15 +0000)]
MIPS: smp-cps: Pull cache init into a function
In preparation for further modifications to mips_cps_core_entry, pull
the L1 cache initialisation out into a separate function. This both
makes the code in mips_cps_core_entry read more clearly, particularly
when modifying it, and shortens it which will become important as code
is added that needs to continue to fit within the reset vector.
Paul Burton [Wed, 3 Feb 2016 03:15:29 +0000 (03:15 +0000)]
MIPS: smp-cps: Ensure our VP ident calculation is correct
When bringing up a CPU, ensure that its local ID as provided by the GIC
matches up with our calculation of it. This is vital, since if the
condition doesn't hold then we won't have configured interrupts
correctly for the VP.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Niklas Cassel <niklas.cassel@axis.com> Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12335/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Wed, 3 Feb 2016 03:15:28 +0000 (03:15 +0000)]
irqchip: mips-gic: Provide VP ID accessor
Provide a gic_read_local_vp_id() function to read the VCNUM field of the
GICs local VP_IDENT register. This will be used by a further patch to
check that the value reported by the GIC matches up with the kernels
calculation.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: James Hogan <james.hogan@imgtec.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12334/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Wed, 3 Feb 2016 03:15:27 +0000 (03:15 +0000)]
irqchip: mips-gic: Use HW IDs for VPE_OTHER_ADDR
The Linux CPU number doesn't necessarily match up with the ID used for a
VP by hardware. Convert the CPU number to the HW ID using mips_cm_vp_id
when writing to the VP(E)_OTHER_ADDR register in order to ensure that we
correctly access registers for the VPs of secondary cores. This most
notably affects systems using CM3, such as those based around I6400.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12333/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Wed, 3 Feb 2016 03:15:26 +0000 (03:15 +0000)]
MIPS: CM: Fix mips_cm_max_vp_width for UP kernels
Fix mips_cm_max_vp_width for UP kernels where it previously referenced
smp_num_siblings, which is not declared for UP kernels. This led to
build errors such as the following:
drivers/built-in.o: In function `$L446':
irq-mips-gic.c:(.text+0x1994): undefined reference to `smp_num_siblings'
drivers/built-in.o:irq-mips-gic.c:(.text+0x199c): more undefined references to `smp_num_siblings' follow
On UP kernels simply return 1, leaving the reference to smp_num_siblings
in place only for SMP kernels.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12332/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Wed, 3 Feb 2016 03:15:23 +0000 (03:15 +0000)]
MIPS: pm-cps: Avoid offset overflow on MIPSr6
This is similar to commit 934c79231c1b ("MIPS: asm: r4kcache: Add MIPS
R6 cache unroll functions"). The CACHE instruction has been redefined
for MIPSr6 and it reduced its offset field to 8 bits. This leads to
micro-assembler field overflow warnings when booting SMP MIPSr6 cores
like the following one:
Markos Chandras [Wed, 3 Feb 2016 03:15:22 +0000 (03:15 +0000)]
MIPS: traps: Make sure secondary cores have a sane ebase register
We shouldn't trust that the secondary cores will have a sane ebase register
(either from the bootloader or during the hardware design phase) so use the
ebase address as calculated by the boot CPU.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: James Hogan <james.hogan@imgtec.com> Cc: Petri Gynther <pgynther@google.com> Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12328/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Wed, 3 Feb 2016 03:15:21 +0000 (03:15 +0000)]
MIPS: Detect MIPSr6 Virtual Processor support
MIPSr6 introduces support for "Virtual Processors", which are
conceptually similar to VPEs from the now-deprecated MT ASE. Detect
whether the system supports VPs using the VP bit in Config5, adding
cpu_has_vp for use by later patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: Joshua Kinard <kumba@gentoo.org> Cc: Steven J. Hill <sjhill@realitydiluted.com> Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12327/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Antony Pavlov [Thu, 17 Mar 2016 03:34:17 +0000 (06:34 +0300)]
MIPS: dts: qca: introduce AR9331 devicetree
This patch introduces devicetree for Atheros AR9331 SoC (AKA Hornet).
The AR9331 chip is a Wi-Fi System-On-Chip (WiSOC),
typically used in very cheap Access Points and Routers.
Antony Pavlov [Thu, 17 Mar 2016 03:34:15 +0000 (06:34 +0300)]
MIPS: ath79: update devicetree clock support for AR9132
Current ath79 clock.c code does not read reference clock and
pll setup from devicetree. E.g. you can set any clock rate value
in board DTS but it will have no effect on the real clk calculation.
This patch fixes some AR9132 devicetree clock support defects:
* clk initialization function ath79_clocks_init_dt_ng()
is introduced; it actually gets pll block base register
address and reference clock from devicetree;
* pll register parsing code is moved to the separate
ar724x_clk_init() function; this function
can be called from platform code or from devicetree code.
Also mips_hpt_frequency value is set from dt, so the appropriate
clock parameter is added to the cpu@0 devicetree node.
The same approach can be used for adding AR9331 devicetree support.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Alban Bedel <albeu@free.fr> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-clk@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12876/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Antony Pavlov [Thu, 17 Mar 2016 03:34:12 +0000 (06:34 +0300)]
MIPS: dts: qca: ar9132: use short references for dt nodes
Here are some Sascha Hauer's arguments for using aliases in the dts
files:
- using aliases reduces the number of indentations in dts files;
- dts files become independent of the layout of the dtsi files
(it becomes possible to introduce another bus {} hierarchy between
a toplevel bus and the devices when you have to);
- less chances for typos. if &i2c2 does not exist you get an error.
If instead you duplicate the whole path in the dts file a typo
in the path will just create another node.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Cc: Alban Bedel <albeu@free.fr> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: Frank Rowand <frowand.list@gmail.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: linux-mips@linux-mips.org Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12873/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hauke Mehrtens [Sat, 19 Mar 2016 17:28:52 +0000 (18:28 +0100)]
MIPS: Lantiq: Make it possible to build in no device tree
Now it is possible to build in no device tree at all and depend on the
boot loader providing one or someone concatenating a device tree to the
end of the image.
Hauke Mehrtens [Sat, 19 Mar 2016 17:28:51 +0000 (18:28 +0100)]
MIPS: Lantiq: Add support for device tree file from boot loader
This fetches the device tree file like it is specified in the MIPS UHI
interface if one was found. This is also used when the device tree file
was appended to the kernel image with cat.
This code is copied from arch/mips/bmips/setup.c.
Aaro Koskinen [Tue, 8 Mar 2016 21:32:26 +0000 (23:32 +0200)]
MIPS: Octeon: Add DTS for D-Link DSR-1000N
Add DTS for D-Link DSR-1000N that is usable as is without any "pruning"
with APPENDED_DTB. Split out the common parts from octeon_3xxx.dts
into octeon_3xxx.dtsi.
Compared to builtin generic DTB, we can specificy fixed links properly
and avoid probing non-existent I2C devices.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: David Daney <ddaney.cavm@gmail.com> Cc: linux-mips@linux-mips.org Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12840/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Aaro Koskinen [Wed, 9 Mar 2016 20:08:42 +0000 (22:08 +0200)]
MIPS: panic immediately when panic_on_oops
MIPS wants to sleep 5 seconds before panicking when panic_on_oops is set,
with no apparent reason. Remove this feature, since some users may want
their systems to fail as quickly as possible.
Users who want to delay reboot after panic can use PANIC_TIMEOUT.
Rafał Miłecki [Mon, 25 Jan 2016 08:50:29 +0000 (09:50 +0100)]
MIPS: BCM47xx: Move SPROM driver to drivers/firmware/
Broadcom ARM home routers store SPROM content in NVRAM just like MIPS
ones. To share SPROM code we need to move it out of arch/mips/ to some
common place. We already have bcm47xx_nvram in firmware path and SPROM
should fit there as well.
This driver is responsible for parsing SoC configuration data into a
struct shared between ssb and bcma buses.
This was tested with BCM4706 & BCM5357C0 (BCM47XX) and BCM4708A0
(ARCH_BCM_5301X).
Aaro Koskinen [Mon, 22 Feb 2016 22:22:57 +0000 (00:22 +0200)]
MIPS: Octeon: Use model string from DTB for unknown board type
Use model string from DTB for board type if the board is unknown.
This is more informative, e.g. with EdgeRouter Pro the /proc/cpuinfo
will display "ubnt,e200 (CN6120p1.1-1000-NSP)" instead of misleading
"Unsupported Board".
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: David Daney <ddaney.cavm@gmail.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12582/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 9 Feb 2016 19:00:06 +0000 (11:00 -0800)]
MIPS: OCTEON: Remove some code limiting NR_IRQS to 255
Follow-on patches for OCTEON III will increase the number of irqs to
potentially more than 256.
Increase the width of the octeon_irq_ciu_to_irq to int to be able to
handle this case. Remove the hacky code that verified that u8 would
not be overflowed.
David Daney [Tue, 2 Feb 2016 01:46:54 +0000 (17:46 -0800)]
MIPS: OCTEON: Extend number of supported CPUs past 32
To support more than 48 CPUs, the bootinfo structure grows a new
coremask structure. Add the definition of the structure and add it to
struct cvmx_bootinfo. In prom_init(), copy the new coremask data into
the sysinfo structure, and use it in smp_setup().
projects / linux-beck.git / log