Do the magnitude/phase coeff correction only if the outlier
is detected. Updating wrong magnitude/phase coeff factor
impacts not only tx gain setting but also leads to poor
performance in congested networks. In the clear environment
the impact is very minimal because the outlier happens
very rarely according to the past experiment. It occured
less than once every 1000 calibrations.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Qualcomm ate up Atheros, all of the old e-mail addresses
no longer work and e-mails sent to it will bounce. Update
the addresses to the new shiny Qualcomm Atheros (QCA) ones.
Cc: stable@kernel.org Cc: netdev@vger.kernel.org Cc: jouni@qca.qualcomm.com Cc: yangjie@qca.qualcomm.com Cc: vthiagar@qca.qualcomm.com Cc: senthilb@qca.qualcomm.com Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IDs found in the Windows driver's ZTEusbnet.inf file from the
ZTE MF100 drivers (O2 UK). Also fixes the ZTE MF626 device
since it really is distinct from the 4G Systems stick and
apparently needs the net interface blacklisted too, while
there's no indication (yet) that the 4G Systems stick does.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's cleaner than the array stuff, and we're about to add a bunch
more blacklist entries. Second, there are devices that need both
the sendsetup and the reserved interface blacklists, which the
current code can't accommodate.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some Stellaris evaluation kits have the JTAG/SWD FTDI chip onboard,
and some, like EK-LM3S9B90, come with a separate In-Circuit Debugger
Interface Board. The ICDI board can also be used stand-alone, for
other boards and chips than the kit it came with. The ICDI has both
old style 20-pin JTAG connector and new style JTAG/SWD 10-pin 1.27mm
pitch connector.
Tested with EK-LM3S9B90, where the BD-ICDI board is included.
Signed-off-by: Peter Stuge <peter@stuge.se> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add vendor and product ID for the SMART USB to serial adapter. These
were meant to be used with their SMART Board whiteboards, but can be
re-purposed for other tasks. Tested and working (at at least 9600 bps).
Signed-off-by: Eric Benoit <eric@ecks.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new runtime PM code has shown that many webcams suffer
from a race condition that may crash them upon resume.
Runtime PM is especially prone to show the problem because
it retains power to the cameras at all times. However
system suspension may also crash the devices and retain
power to the devices.
The only way to solve this problem without races is in
usbcore with the RESET_RESUME quirk.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern points out that after spin_unlock(&ps->lock) there is no
guarantee that ps->pid won't be freed. Since kill_pid_info_as_uid() is
called after the spin_unlock(), the pid passed to it must be pinned.
In the usb printer class specific request get_device_id the value of
wIndex is (interface << 8 | altsetting) instead of just interface.
This enables the detection of some printers with libusb.
At least some OHCI hardware (such as the MCP89) fails to flag any change
in the host status register or the port status registers when receiving
a remote wakeup while in D3 state. This results in the controller being
resumed but no device state change being noticed, at which point the
controller is put back to sleep again. Since there doesn't seem to be any
reliable way to identify the state change, just unconditionally resume the
hub. It'll be put back to sleep in the near future anyway if there are no
active devices attached to it.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch solves two things:
1) Enables autosense emulation code to correctly
interpret descriptor format sense data, and
2) Fixes a bug whereby the autosense emulation
code would overwrite descriptor format sense data
with SENSE KEY HARDWARE ERROR in fixed format, to
incorrectly look like this:
Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc] Sense Key : Recovered Error [current] [descriptor]
Oct 21 14:11:07 localhost kernel: Descriptor sense data with sense descriptors (in hex):
Oct 21 14:11:07 localhost kernel: 72 01 04 1d 00 00 00 0e 09 0c 00 00 00 00 00 00
Oct 21 14:11:07 localhost kernel: 00 4f 00 c2 00 50
Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc] ASC=0x4 ASCQ=0x1d
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is a re-orginzation of core_tmr_lun_reset() logic to properly
scan the active tmr_list, dev->state_task_list and qobj->qobj_list w/ the
relivent locks held, and performing a list_move_tail onto seperate local
scope lists before performing the full drain.
This involves breaking out the code into three seperate list specific
functions: core_tmr_drain_tmr_list(), core_tmr_drain_task_list() and
core_tmr_drain_cmd_list().
(nab: Include target: Remove non-active tasks from execute list during
LUN_RESET patch to address original breakage)
Reported-by: Roland Dreier <roland@purestorage.com> Cc: Roland Dreier <roland@purestorage.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Depending on the implementation of the hardware blinking function in
blink_set(), the led can support hardware blinking for some values of
delay_on and delay_off and fall-back to software blinking for some other
values.
Turning off the blink_timer unconditionally before starting to blink
make sure that a sequence like:
OFF
hardware blinking
software blinking
hardware blinking
does not leave the software blinking timer active.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
epoll can acquire recursively acquire ep->mtx on multiple "struct
eventpoll"s at once in the case where one epoll fd is monitoring another
epoll fd. This is perfectly OK, since we're careful about the lock
ordering, but it causes spurious lockdep warnings. Annotate the recursion
using mutex_lock_nested, and add a comment explaining the nesting rules
for good measure.
Recent versions of systemd are triggering this, and it can also be
demonstrated with the following trivial test program:
--------------------8<--------------------
int main(void) {
int e1, e2;
struct epoll_event evt = {
.events = EPOLLIN
};
When compiling an i386_defconfig kernel with gcc-4.6.1-9.fc15.i686, I
noticed a warning about the asm operand for test_bit in kprobes'
can_boost. I discovered that this caused only the first long of
twobyte_is_boostable[] to be output.
Jakub filed and fixed gcc PR50571 to correct the warning and this output
issue. But to solve it for less current gcc, we can make kprobes'
twobyte_is_boostable[] non-const, and it won't be optimized out.
Before:
CC arch/x86/kernel/kprobes.o
In file included from include/linux/bitops.h:22:0,
from include/linux/kernel.h:17,
from [...]/arch/x86/include/asm/percpu.h:44,
from [...]/arch/x86/include/asm/current.h:5,
from [...]/arch/x86/include/asm/processor.h:15,
from [...]/arch/x86/include/asm/atomic.h:6,
from include/linux/atomic.h:4,
from include/linux/mutex.h:18,
from include/linux/notifier.h:13,
from include/linux/kprobes.h:34,
from arch/x86/kernel/kprobes.c:43:
[...]/arch/x86/include/asm/bitops.h: In function ‘can_boost.part.1’:
[...]/arch/x86/include/asm/bitops.h:319:2: warning: use of memory input
without lvalue in asm operand 1 is deprecated [enabled by default]
This is a workaround for a UV2 hub bug that affects the format of system
global addresses.
The GRU API for UV2 was inadvertently broken by a hardware change. The
format of the physical address used for TLB dropins and for addresses used
with instructions running in unmapped mode has changed. This change was
not documented and became apparent only when diags failed running on
system simulators.
For UV1, TLB and GRU instruction physical addresses are identical to
socket physical addresses (although high NASID bits must be OR'ed into the
address).
For UV2, socket physical addresses need to be converted. The NODE portion
of the physical address needs to be shifted so that the low bit is in bit
39 or bit 40, depending on an MMR value.
It is not yet clear if this bug will be fixed in a silicon respin. If it
is fixed, the hub revision will be incremented & the workaround disabled.
Signed-off-by: Jack Steiner <steiner@sgi.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a bug with the handling of REPORT TARGET PORT GROUPS
containing a smaller allocation length than the payload requires causing
memory writes beyond the end of the buffer. This patch checks for the
minimum 4 byte length for the response payload length, and also checks
upon each loop of T10_ALUA(su_dev)->tg_pt_gps_list to ensure the Target
port group and Target port descriptor list is able to fit into the
remaining allocation length.
If the response payload exceeds the allocation length length, then rd_len
is still increments to indicate to the initiator that the payload has
been truncated.
Reported-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains a bugfix for TMR LUN_RESET related to TRANSPORT_FREE_CMD_INTR
operation, where core_tmr_drain_cmd_list() will now skip processing for this
case to prevent an ABORT_TASK status from being returned for descriptors that
are already queued up to be released by processing thread context.
Cc: Roland Dreier <roland@purestorage.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a bug where transport_send_task_abort() could be called
during LUN_RESET to return SAM_STAT_TASK_ABORTED + tfo->queue_status(), when
SCF_SENT_CHECK_CONDITION -> tfo->queue_status() has already been sent from
within another context via transport_send_check_condition_and_sense().
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a bug in LUN_RESET operation with transport_cmd_finish_abort()
where transport_remove_cmd_from_queue() was incorrectly being called, causing
descriptors with t_state == TRANSPORT_FREE_CMD_INTR to be incorrectly removed
from qobj->qobj_list during process context release. This change ensures the
descriptor is only removed via transport_remove_cmd_from_queue() when doing a
direct release via transport_generic_remove().
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch addresses a bug with the lio-core-2.6.git conversion of
transport_add_cmd_to_queue() to use a single embedded list_head, instead
of individual struct se_queue_req allocations allowing a single se_cmd to
be added to the queue mulitple times. This was changed in the following:
The problem is that some target code still assumes performing multiple
adds is allowed via transport_add_cmd_to_queue(), which ends up causing
list corruption in qobj->qobj_list code. This patch addresses this
by removing an existing struct se_cmd from the list before the add, and
removes an unnecessary list walk in transport_remove_cmd_from_queue()
It also changes cmd->t_transport_queue_active to use explict sets intead
of increment/decrement to prevent confusion during exception path handling.
Signed-off-by: Roland Dreier <roland@purestorage.com> Cc: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the old Conexant chips (5045, 5047, 5051 and 5066), a single EAPD
may handle both headphone and speaker outputs while it's assigned only
to one of them. Turning off dynamically leads to the unexpected silent
output in such a configuration with the auto-mute function.
Since it's difficult to know how the EAPD is handled in the actual h/w
implementation, better to keep EAPD on while running for such codecs.
The purpose of this patch is to remove a section of "bad" code that
assigns the last DAC to ports E or F in order to support notebooks
with docking in earlier days, around ALSA 1.0.19 - 21. This is not
necessary now and actually breaks some configurations that use these
ports as other devices. This have been tested on several different
configurations to make sure that it is working for different combinations.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Besides being unnecessary, it is too small (currently truncates
responses to 60 bytes). The mid-layer will have already allocated a
sufficiently sized buffer, just kmap and copy into it directly.
Reported-by: Derick Marks <derick.w.marks@intel.com> Tested-by: Derick Marks <derick.w.marks@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During kdump testing I noticed timeouts when initialising each IPR
adapter. While the driver has logic to detect an adapter in an
indeterminate state, it wasn't triggering and each adapter went
through a 5 minute timeout before finally going operational.
Some analysis showed the needs_hard_reset flag wasn't getting set.
We can check the reset_devices kernel parameter which is set by
kdump and force a full reset. This fixes the problem.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch for megaraid_sas will fix a potential bad pointer access
in megasas_reset_timer(), when a MegaRAID 9265/9285 or 9360/9380 gets a
timeout. megasas_build_io_fusion() sets SCp.ptr to be a struct
megasas_cmd_fusion *, but then megasas_reset_timer() was casting SCp.ptr to be
a struct megasas_cmd *, then trying to access cmd->instance, which is invalid.
Just loading instance from scmd->device->host->hostdata in
megasas_reset_timer() fixes the issue.
Signed-off-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 15bed0f2f added a quirk for the e823 Ricoh card reader to lower the
base frequency. However, the quirk first checks to see if the proprietary
MMC controller is disabled, and returns if so. On some devices, such as the
Lenovo X220, the MMC controller is already disabled by firmware it seems,
but the frequency change is still needed so sdhci-pci can talk to the cards.
Since the MMC controller is disabled, the frequency fixup was never being run
on these machines.
This moves the e823 check above the MMC controller check so that it always
gets run.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=722509
f39b2dd9d ("mmc: core: Bus width testing needs to handle suspend/resume")
added code to only compare read-only ext_csd fields in bus width testing
code, yet it's comparing some fields that are never set.
The affected fields are ext_csd.raw_erased_mem_count and
ext_csd.raw_partition_support.
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com> Acked-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During a rescan operation mmc_attach(sd|mmc|sdio) functions are
called. The error handling in these function can trigger a detach
of the bus, which also meant a power off. This is not notified by
the rescan operation which then continues to the next attach function.
If a power off has been done, the framework must never send any
new commands to the host driver, without first doing a new power up.
This will most likely trigger any host driver to hang.
Moving power off out of detach and instead handle power off
separately when it is actually needed, solves the issue.
Commit 9b9fe724 accidentally used RADEON_GPIO_EN_* where
RADEON_GPIO_MASK_* was intended. This caused improper initialization
of I2C buses, mostly visible when setting i2c_algo_bit.bit_test=1.
Using the right constants fixes the problem.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Cc: Jerome Glisse <j.glisse@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When force == false, we don't do load detection in the connector
detect functions. Unforunately, we also return the previous
connector state so we never get disconnect events for DVI-I, DVI-A,
or VGA. Save whether we detected the monitor via load detection
previously and use that to determine whether we return the previous
state or not.
DVI-D and HDMI-A are digital only, so there's no need to
attempt analog load detect. Also, skip bail before the
!force check, or we fail to get a disconnect events.
The next patches in the series attempt to fix disconnect
events for connectors with analog support (DVI-I, HDMI-B,
DVI-A).
The commit 47356eb67285014527a5ab87543ba1fae3d1e10a introduced a
mechanism to record the backlight level only at disabling time, but it
also introduced a regression. Since intel_lvds_enable() may be called
without disabling (e.g. intel_lvds_commit() calls it unconditionally),
the backlight gets back to the last recorded value. For example, this
happens when you dim the backlight, close the lid and open the lid,
then the backlight suddenly goes to the brightest.
This patch fixes the bug by recording the backlight level always
when changed via intel_panel_set_backlight(). And,
intel_panel_{enable|disable}_backlight() call the internal function not
to update the recorded level wrongly.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Keith Packard <keithp@keithp.com> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Talking to the eDP DDC channel requires that the panel be powered
up. Wrap both the EDID and modes fetch code with calls to turn the vdd
power on and back off.
Signed-off-by: Keith Packard <keithp@keithp.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting the chain (CH) bit in the link TRB of isochronous transfer rings
is required by AMD 0.96 xHCI host controller to successfully transverse
multi-TRB TD that span through different memory segments.
When a Missed Service Error event occurs, if the chain bit is not set in
the link TRB and the host skips TDs which just across a link TRB, the
host may falsely recognize the link TRB as a normal TRB. You can see
this may cause big trouble - the host does not jump to the right address
which is pointed by the link TRB, but continue fetching the memory which
is after the link TRB address, which may not even belong to the host,
and the result cannot be predicted.
This causes some big problems. Without the former patch I sent: "xHCI:
prevent infinite loop when processing MSE event", the system may hang.
With that patch applied, system does not hang, but the host still access
wrong memory address and isoc transfer will fail. With this patch,
isochronous transfer works as expected.
This patch should be applied to kernels as old as 2.6.36, which was when
the first isochronous support was added for the xHCI host controller.
There are 2 situations wherein the xhci_ring* might not get freed:
- When xhci_ring_alloc() -> xhci_segment_alloc() returns NULL and
we goto the fail: label in xhci_ring_alloc. In this case, the ring
will not get kfreed.
- When the num_segs argument to xhci_ring_alloc is passed as 0 and
we try to free the rung after that.
( This doesn't really happen as of now in the code but we seem to
be entertaining num_segs=0 in xhci_ring_alloc )
This should be backported to kernels as old as 2.6.31.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1489) works around a hardware bug in MosChip EHCI
controllers. Evidently when one of these controllers increments the
frame-index register, it changes the three low-order bits (the
microframe counter) before changing the higher order bits (the frame
counter). If the register is read at just the wrong time, the value
obtained is too low by 8.
When the appropriate quirk flag is set, we work around this problem by
reading the frame-index register a second time if the first value's
three low-order bits are all 0. This gives the hardware a chance to
finish updating the register, yielding the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Jason N Pitt <jpitt@fhcrc.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It will break the pxa serial driver when the system resumes from suspend mode
as it will try to set baud rate divider register in set_termios but with
clock off. The register value can not be set correctly on some platform if
the clock is disabled. The pxa driver will check the value and report the
following warning:
------------[ cut here ]------------
WARNING: at drivers/tty/serial/pxa.c:545 serial_pxa_set_termios+0x1dc/0x250()
Modules linked in:
[<c0281f30>] (unwind_backtrace+0x0/0xf0) from [<c029341c>] (warn_slowpath_common+0x4c/0x64)
[<c029341c>] (warn_slowpath_common+0x4c/0x64) from [<c029344c>] (warn_slowpath_null+0x18/0x1c)
[<c029344c>] (warn_slowpath_null+0x18/0x1c) from [<c044b1e4>] (serial_pxa_set_termios+0x1dc/0x250)
[<c044b1e4>] (serial_pxa_set_termios+0x1dc/0x250) from [<c044a840>] (uart_resume_port+0x128/0x2dc)
[<c044a840>] (uart_resume_port+0x128/0x2dc) from [<c044bbe0>] (serial_pxa_resume+0x18/0x24)
[<c044bbe0>] (serial_pxa_resume+0x18/0x24) from [<c0454d34>] (platform_pm_resume+0x40/0x4c)
[<c0454d34>] (platform_pm_resume+0x40/0x4c) from [<c0457ebc>] (pm_op+0x68/0xb4)
[<c0457ebc>] (pm_op+0x68/0xb4) from [<c0458368>] (device_resume+0xb0/0xec)
[<c0458368>] (device_resume+0xb0/0xec) from [<c04584c8>] (dpm_resume+0xe0/0x194)
[<c04584c8>] (dpm_resume+0xe0/0x194) from [<c0458588>] (dpm_resume_end+0xc/0x18)
[<c0458588>] (dpm_resume_end+0xc/0x18) from [<c02c518c>] (suspend_devices_and_enter+0x16c/0x1ac)
[<c02c518c>] (suspend_devices_and_enter+0x16c/0x1ac) from [<c02c5278>] (enter_state+0xac/0xdc)
[<c02c5278>] (enter_state+0xac/0xdc) from [<c02c48ec>] (state_store+0xa0/0xbc)
[<c02c48ec>] (state_store+0xa0/0xbc) from [<c0408f7c>] (kobj_attr_store+0x18/0x1c)
[<c0408f7c>] (kobj_attr_store+0x18/0x1c) from [<c034a6a4>] (sysfs_write_file+0x108/0x140)
[<c034a6a4>] (sysfs_write_file+0x108/0x140) from [<c02fb798>] (vfs_write+0xac/0x134)
[<c02fb798>] (vfs_write+0xac/0x134) from [<c02fb8cc>] (sys_write+0x3c/0x68)
[<c02fb8cc>] (sys_write+0x3c/0x68) from [<c027c700>] (ret_fast_syscall+0x0/0x2c)
---[ end trace 88289eceb4675b04 ]---
This patch fix the problem by adding the power on opertion back for uart
console when console_suspend_enabled is true.
netif_notify_peers() caused a kernel warning in netvsc_linkstatus_callback(),
because netvsc_linkstatus_callback() is within IRQ context. So we move
the first call to netif_notify_peers() into queued work as well, but with
zero delay.
In addition to "staging-next", this should also be back-ported to stable
kernels 2.6.32 and later.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a LUN larger than 2 TB is attached to a Linux VM on Hyper-V, we currently
report a maximum size of 2 TB. This patch resolves the issue in hv_storvsc.
Thanks to Robert Scheck <robert.scheck@etes.de> for reporting the issue.
Reported-by: Robert Scheck <robert.scheck@etes.de> Signed-off-by: Mike Sterling <mike.sterling@microsoft.com> Signed-off-by: K.Y. Srinivasan <kys@microsoft.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the usermode app does an ioctl over this serial device by
using TIOCMIWAIT, then the code will wait by setting the current
task state to TASK_INTERRUPTIBLE and then calling schedule().
This will be woken up by the qt2_process_modem_status on URB
completion when the port_extra->shadowMSR is set to the new
modem status.
However, this could result in a lost wakeup scenario due to a race
in the logic in the qt2_ioctl(TIOCMIWAIT) loop and the URB completion
for new modem status in qt2_process_modem_status.
Due to this, the usermode app's task will continue to sleep despite a
change in the modem status.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The serqt_usb2 driver will not work properly with the ssu100 device
even though it claims to support it. The ssu100 is supported by the
ssu100 driver in mainline so there is no need to have it claimed by
serqt_usb2.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revert changes in definitions that were submitted on May 11 2011 and
committed on June 7 2011. No reason for the change in these values was
given in the patch comment, it broke compatibility with older
versions, and was difficult to detect by the simultaneous move of the
lines of code.
Signed-off-by: Alexander Thomas <alexander.thomas@esaturnus.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A return value of -EINPROGRESS from pm_runtime_get indicates that
the device is already resuming due to a previous call. Internally,
usb_autopm_get_interface_async doesn't treat this as an error and
increments the usage count, but passes the error status along
to the caller. The logical assumption of the caller is that
any negative return value reflects the device not resuming
and the pm_usage_cnt not being incremented. Since the usage count
is being incremented and the device is resuming, return success (0)
instead.
Signed-off-by: James Wylder <james.wylder@motorola.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If tty_add_file fails at the point it is now, we have to revert all
the changes we did to the tty. It means either decrease all refcounts
if this was a tty reopen or delete the tty if it was newly allocated.
There was a try to fix this in v3.0-rc2 using tty_release in 0259894c7
(TTY: fix fail path in tty_open). But instead it introduced a NULL
dereference. It's because tty_release dereferences
filp->private_data, but that one is set even in our tty_add_file. And
when tty_add_file fails, it's still NULL/garbage. Hence tty_release
cannot be called there.
To circumvent the original leak (and the current NULL deref) we split
tty_add_file into two functions, making the latter non-failing. In
that case we may do the former early in open, where handling failures
is easy. The latter stays as it is now. So there is no change in
functionality.
The original bug (leak) was introduced by f573bd176 (tty: Remove
__GFP_NOFAIL from tty_add_file()). Thanks Dan for reporting this.
Later, we may split tty_release into more functions and call only some
of them in this fail path instead. (If at all possible.)
Introduced-in: v2.6.37-rc2 Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Pekka Enberg <penberg@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When tty_driver_lookup_tty fails in tty_open, we forget to drop a
reference to the tty driver. This was added by commit 4a2b5fddd5 (Move
tty lookup/reopen to caller).
Fix that by adding tty_driver_kref_put to the fail path.
I will refactor the code later. This is for the ease of backporting to
stable.
We should call cifs_all_info_to_fattr in rc == 0 case only.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Jeff Layton <jlayton@samba.org> Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Mon, 24 Oct 2011 05:08:24 +0000 (07:08 +0200)]
Merge git://git.infradead.org/iommu-2.6
* git://git.infradead.org/iommu-2.6:
intel-iommu: fix superpage support in pfn_to_dma_pte()
intel-iommu: set iommu_superpage on VM domains to lowest common denominator
intel-iommu: fix return value of iommu_unmap() API
MAINTAINERS: Update VT-d entry for drivers/pci -> drivers/iommu move
intel-iommu: Export a flag indicating that the IOMMU is used for iGFX.
intel-iommu: Workaround IOTLB hang on Ironlake GPU
intel-iommu: Fix AB-BA lockdep report
Takashi Iwai [Sun, 23 Oct 2011 21:19:12 +0000 (23:19 +0200)]
x86: Fix S4 regression
Commit 4b239f458 ("x86-64, mm: Put early page table high") causes a S4
regression since 2.6.39, namely the machine reboots occasionally at S4
resume. It doesn't happen always, overall rate is about 1/20. But,
like other bugs, once when this happens, it continues to happen.
This patch fixes the problem by essentially reverting the memory
assignment in the older way.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Cc: <stable@kernel.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Yinghai Lu <yinghai.lu@oracle.com>
[ We'll hopefully find the real fix, but that's too late for 3.1 now ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When allocating a set of jobs from kc->job_pool, job->master_job must be
set (to point to itself) so that the mempool item gets freed when the
master_job completes.
ARM: S3C24XX: Fix s3c24xx build errors if !CONFIG_PM
v2:
- register_syscore_ops(&s3c24xx_irq_syscore_ops) does not need to be
conditionally compiled out, it is already optimized out on !CONFIG_PM
- fix also s3c2412 and s3c2416 affected by the same build issue
v1:
s3c2440.c fails to build if !CONFIG_PM because in such case
s3c2410_pm_syscore_ops is not defined. Same error should happen also
in s3c2410.c and s3c2442.c
Signed-off-by: Domenico Andreoli <cavokz@gmail.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Nick Bowler [Thu, 20 Oct 2011 12:16:55 +0000 (14:16 +0200)]
crypto: ghash - Avoid null pointer dereference if no key is set
The ghash_update function passes a pointer to gf128mul_4k_lle which will
be NULL if ghash_setkey is not called or if the most recent call to
ghash_setkey failed to allocate memory. This causes an oops. Fix this
up by returning an error code in the null case.
This is trivially triggered from unprivileged userspace through the
AF_ALG interface by simply writing to the socket without setting a key.
The ghash_final function has a similar issue, but triggering it requires
a memory allocation failure in ghash_setkey _after_ at least one
successful call to ghash_update.
Marek Szyprowski [Fri, 21 Oct 2011 09:04:54 +0000 (18:04 +0900)]
ARM: S5P: fix offset calculation on gpio-interrupt
Offsets of the irq controller registers were calculated
correctly only for first GPIO bank. This patch fixes
calculation of the register offsets for all GPIO banks.
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
fib_rules: fix unresolved_rules counting
r8169: fix wrong eee setting for rlt8111evl
r8169: fix driver shutdown WoL regression.
ehea: Change maintainer to me
pptp: pptp_rcv_core() misses pskb_may_pull() call
tproxy: copy transparent flag when creating a time wait
pptp: fix skb leak in pptp_xmit()
bonding: use local function pointer of bond->recv_probe in bond_handle_frame
smsc911x: Add support for SMSC LAN89218
tg3: negate USE_PHYLIB flag check
netconsole: enable netconsole can make net_device refcnt incorrent
bluetooth: Properly clone LSM attributes to newly created child connections
l2tp: fix a potential skb leak in l2tp_xmit_skb()
bridge: fix hang on removal of bridge via netlink
x25: Prevent skb overreads when checking call user data
x25: Handle undersized/fragmented skbs
x25: Validate incoming call user data lengths
udplite: fast-path computation of checksum coverage
IPVS netns shutdown/startup dead-lock
netfilter: nf_conntrack: fix event flooding in GRE protocol tracker
Jean Delvare [Thu, 20 Oct 2011 07:06:45 +0000 (03:06 -0400)]
hwmon: (w83627ehf) Fix negative 8-bit temperature values
Since 8-bit temperature values are now handled in 16-bit struct
members, values have to be cast to s8 for negative temperatures to be
properly handled. This is broken since kernel version 2.6.39
(commit bce26c58df86599c9570cee83eac58bdaae760e4.)
Hugh Dickins [Wed, 19 Oct 2011 19:50:35 +0000 (12:50 -0700)]
mm: fix race between mremap and removing migration entry
I don't usually pay much attention to the stale "? " addresses in
stack backtraces, but this lucky report from Pawel Sikora hints that
mremap's move_ptes() has inadequate locking against page migration.
mremap's down_write of mmap_sem, together with i_mmap_mutex or lock,
and pagetable locks, were good enough before page migration (with its
requirement that every migration entry be found) came in, and enough
while migration always held mmap_sem; but not enough nowadays, when
there's memory hotremove and compaction.
The danger is that move_ptes() lets a migration entry dodge around
behind remove_migration_pte()'s back, so it's in the old location when
looking at the new, then in the new location when looking at the old.
Either mremap's move_ptes() must additionally take anon_vma lock(), or
migration's remove_migration_pte() must stop peeking for is_swap_entry()
before it takes pagetable lock.
Consensus chooses the latter: we prefer to add overhead to migration
than to mremapping, which gets used by JVMs and by exec stack setup.
Kjetil Oftedal [Wed, 19 Oct 2011 23:20:50 +0000 (16:20 -0700)]
sparc: Add alignment flag to PCI expansion resources
Currently no type of alignment is specified for PCI expansion roms while
parsing the openfirmware tree. This causes calls to pci_map_rom() to fail.
IORESOURCE_SIZEALIGN is the default alignment used for rom resouces in
pci/probe.c, and has been verified to work with various cards on a ultra 10.
Signed-off-By: Kjetil Oftedal <oftedal@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
françois romieu [Fri, 14 Oct 2011 00:57:45 +0000 (00:57 +0000)]
r8169: fix driver shutdown WoL regression.
Due to commit 92fc43b4159b518f5baae57301f26d770b0834c9 ("r8169: modify the
flow of the hw reset."), rtl8169_hw_reset stomps during driver shutdown on
RxConfig bits which are needed for WOL on some versions of the hardware.
As these bits were formerly set from the r81{0x, 68}_pll_power_down methods,
factor them out for use in the driver shutdown (rtl_shutdown) handler.
I favored __rtl8169_get_wol() -hardware state indication- over
RTL_FEATURE_WOL as the latter has become a good candidate for removal.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Hayes <hayeswang@realtek.com> Tested-by: Marc Ballarin <ballarin.marc@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Cc: Breno Leitao <leitao@linux.vnet.ibm.com> Acked-by: Breno Leitão <leitao@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 19 Oct 2011 13:43:24 +0000 (06:43 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms/atom: fix handling of FB scratch indices
drm/radeon/kms/DCE4.1: fix Select_CrtcSource EncodeMode setting for DP bridges (v2)
drm/radeon/kms/DCE4.1: ss is not supported on the internal pplls
drm/radeon/kms/DCE4.1: fix dig encoder to transmitter mapping
ttm: Fix error-path using an uninitialized value
Antonio Ospite [Wed, 12 Oct 2011 20:59:26 +0000 (17:59 -0300)]
[media] videodev: fix a NULL pointer dereference in v4l2_device_release()
The change in 8280b66 does not cover the case when v4l2_dev is already
NULL, fix that.
With a Kinect sensor, seen as an USB camera using GSPCA in this context,
a NULL pointer dereference BUG can be triggered by just unplugging the
device after the camera driver has been loaded.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allen Kay [Fri, 14 Oct 2011 19:32:46 +0000 (12:32 -0700)]
intel-iommu: fix superpage support in pfn_to_dma_pte()
If target_level == 0, current code breaks out of the while-loop if
SUPERPAGE bit is set. We should also break out if PTE is not present.
If we don't do this, KVM calls to iommu_iova_to_phys() will cause
pfn_to_dma_pte() to create mapping for 4KiB pages.
Signed-off-by: Allen Kay <allen.m.kay@intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Allen Kay [Fri, 14 Oct 2011 19:32:17 +0000 (12:32 -0700)]
intel-iommu: set iommu_superpage on VM domains to lowest common denominator
set dmar->iommu_superpage field to the smallest common denominator
of super page sizes supported by all active VT-d engines. Initialize
this field in intel_iommu_domain_init() API so intel_iommu_map() API
will be able to use iommu_superpage field to determine the appropriate
super page size to use.
Signed-off-by: Allen Kay <allen.m.kay@intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Allen Kay [Fri, 14 Oct 2011 19:31:54 +0000 (12:31 -0700)]
intel-iommu: fix return value of iommu_unmap() API
iommu_unmap() API expects IOMMU drivers to return the actual page order
of the address being unmapped. Previous code was just returning page
order passed in from the caller. This patch fixes this problem.
Signed-off-by: Allen Kay <allen.m.kay@intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Roland Dreier [Tue, 11 Oct 2011 00:07:15 +0000 (17:07 -0700)]
MAINTAINERS: Update VT-d entry for drivers/pci -> drivers/iommu move
Commit 166e9278a3f9 ("x86/ia64: intel-iommu: move to drivers/iommu/")
moved the VT-d driver to drivers/iommu, but left the "F:" line in
MAINTAINERS pointing to drivers/pci, which breaks scripts/get_maintainer.pl.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Alex Deucher [Wed, 19 Oct 2011 00:10:05 +0000 (20:10 -0400)]
drm/radeon/kms/atom: fix handling of FB scratch indices
FB scratch indices are dword indices, but we were treating
them as byte indices. As such, we were getting the wrong
FB scratch data for non-0 indices. Fix the indices and
guard the indexing against indices larger than the scratch
allocation.
Fixes memory corruption on some boards if data was written
past the end of the FB scratch array.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reported-by: Dave Airlie <airlied@redhat.com> Tested-by: Dave Airlie <airlied@redhat.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
pptp_rcv_core() is a nice example of a function assuming everything it
needs is available in skb head.
Reported-by: Bradley Peterson <despite@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KOVACS Krisztian [Tue, 18 Oct 2011 10:17:35 +0000 (10:17 +0000)]
tproxy: copy transparent flag when creating a time wait
The transparent socket option setting was not copied to the time wait
socket when an inet socket was being replaced by a time wait socket. This
broke the --transparent option of the socket match and may have caused
that FIN packets belonging to sockets in FIN_WAIT2 or TIME_WAIT state
were being dropped by the packet filter.
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
Mitsuo Hayasaka [Wed, 12 Oct 2011 16:04:29 +0000 (16:04 +0000)]
bonding: use local function pointer of bond->recv_probe in bond_handle_frame
The bond->recv_probe is called in bond_handle_frame() when
a packet is received, but bond_close() sets it to NULL. So,
a panic occurs when both functions work in parallel.
Why this happen:
After null pointer check of bond->recv_probe, an sk_buff is
duplicated and bond->recv_probe is called in bond_handle_frame.
So, a panic occurs when bond_close() is called between the
check and call of bond->recv_probe.
Patch:
This patch uses a local function pointer of bond->recv_probe
in bond_handle_frame(). So, it can avoid the null pointer
dereference.
Signed-off-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Cc: Jay Vosburgh <fubar@us.ibm.com> Cc: Andy Gospodarek <andy@greyhouse.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: WANG Cong <xiyou.wangcong@gmail.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log