Brian Norris [Wed, 28 Aug 2013 01:45:10 +0000 (18:45 -0700)]
mtd: nand: hack ONFI for non-power-of-2 dimensions
Some bright specification writers decided to write this in the ONFI spec
(from ONFI 3.0, Section 3.1):
"The number of blocks and number of pages per block is not required to
be a power of two. In the case where one of these values is not a
power of two, the corresponding address shall be rounded to an
integral number of bits such that it addresses a range up to the
subsequent power of two value. The host shall not access upper
addresses in a range that is shown as not supported."
This breaks every assumption MTD makes about NAND block/chip-size
dimensions -- they *must* be a power of two!
And of course, an enterprising manufacturer has made use of this lovely
freedom. Exhibit A: Micron MT29F32G08CBADAWP
"- Plane size: 2 planes x 1064 blocks per plane
- Device size: 32Gb: 2128 blockss [sic]"
This quickly hits a BUG() in nand_base.c, since the extra dimensions
overflow so we think it's a second chip (on my single-chip setup):
ONFI param page 0 valid
ONFI flash detected
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x44 (Micron MT29F32G08CBADAWP), 4256MiB, page size: 8192, OOB size: 744
------------[ cut here ]------------
kernel BUG at drivers/mtd/nand/nand_base.c:203!
Internal error: Oops - BUG: 0 [#1] SMP ARM
[... trim ...]
[<c02cf3e4>] (nand_select_chip+0x18/0x2c) from [<c02d25c0>] (nand_do_read_ops+0x90/0x424)
[<c02d25c0>] (nand_do_read_ops+0x90/0x424) from [<c02d2dd8>] (nand_read+0x54/0x78)
[<c02d2dd8>] (nand_read+0x54/0x78) from [<c02ad2c8>] (mtd_read+0x84/0xbc)
[<c02ad2c8>] (mtd_read+0x84/0xbc) from [<c02d4b28>] (scan_read.clone.4+0x4c/0x64)
[<c02d4b28>] (scan_read.clone.4+0x4c/0x64) from [<c02d4c88>] (search_bbt+0x148/0x290)
[<c02d4c88>] (search_bbt+0x148/0x290) from [<c02d4ea4>] (nand_scan_bbt+0xd4/0x5c0)
[... trim ...]
---[ end trace 0c9363860d865ff2 ]---
So to fix this, just truncate these dimensions down to the greatest
power-of-2 dimension that is less than or equal to the specified
dimension.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: <stable@vger.kernel.org>
Ezequiel Garcia [Fri, 4 Oct 2013 18:30:38 +0000 (15:30 -0300)]
mtd: nand: pxa3xx: Allocate data buffer on detected flash size
This commit replaces the currently hardcoded buffer size, by a
dynamic detection scheme. First a small 256 bytes buffer is allocated
so the device can be detected (using READID and friends commands).
After detection, this buffer is released and a new buffer is allocated
to acommodate the page size plus out-of-band size.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Tested-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Priyanka Jain [Tue, 15 Oct 2013 05:39:05 +0000 (11:09 +0530)]
mtd: m25p80: Add support for Micron N25Q512A memory
Micron N25Q512A is a spi flash memory with following features:
-64MB size, 1.8V, Mulitple I/O, 4KB Sector erase memory.
-Memory is organised as 1024(64KB) main sectors.
-Each sector is divided into 256 pages.
-Register set/Opcodes are similar to other N25Q family products.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Mike Dunn [Thu, 10 Oct 2013 17:25:27 +0000 (10:25 -0700)]
mtd: docg4: fix status polling loop
The loop that polls the status register waiting for an operation to complete
foolishly bases the timeout simply on the number of loop iterations that have
ocurred. When I increased the processor clock speed, timeouts started to appear
for long block erasure operations. This patch measures the timeout using
jiffies.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Jingoo Han [Mon, 23 Sep 2013 01:32:27 +0000 (10:32 +0900)]
mtd: denali: remove unnecessary pci_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Jingoo Han [Mon, 23 Sep 2013 01:30:52 +0000 (10:30 +0900)]
mtd: pci: remove unnecessary pci_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
phram was 32-bit limited by design. Machines are growing up, but phram
module is still useful. Update it. The patch is bigger than minimum,
because simple_strtoul() is obsolete.
Tested on MIPS64 and compile-tested for PPC (32 bit).
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com> Reviewed-by: Joern Engel <joern@logfs.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Jingoo Han [Mon, 9 Sep 2013 05:42:52 +0000 (14:42 +0900)]
mtd: plat-ram: Remove casting the return value which is a void pointer
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Current code sets the mtd->type with MTD_NANDFLASH for both
SLC and MLC. So the jffs2 may supports the MLC nand, but in actually,
the jffs2 should not support the MLC.
This patch uses the nand_is_slc() to check the nand cell type,
and set the mtd->type with the right nand type.
After this patch, the jffs2 only supports the SLC nand.
The side-effect of this patch:
Before this patch, the ioctl(MEMGETINFO) can only return with the
MTD_NANDFLASH; but after this patch, the ioctl(MEMGETINFO) will
return with the MTD_NANDFLASH for SLC, and MTD_MLCNANDFLASH for MLC.
So the user applictions(such as mtd-utils) should also changes a little
for this.
Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This helper detects that whether the mtd's type is nand type.
Now, it's clear that the MTD_NANDFLASH stands for SLC nand only.
So use the mtd_type_is_nand() to replace the old check method
to do the nand type (include the SLC and MLC) check.
Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtd: nand: add more comment for MTD_NANDFLASH/MTD_MLCNANDFLASH
In current code, the MTD_NANDFLASH is used to represent both the SLC and
MLC. It is confusing to us.
By adding an explicit comment about these two macros, this patch makes it
clear that:
MTD_NANDFLASH : stands for SLC NAND,
MTD_MLCNANDFLASH : stands for MLC NAND (including TLC).
Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If the ONFI extended parameter page gives codeword_size == 0, the
extended ECC information is corrupt and should not be used. Currently,
we (correctly) avoid using the information, but we don't report the
error to the caller, so the caller doesn't know that we didn't
initialize ecc_strength_ds and ecc_step_ds. Now the caller can warn the
user that it does not have sufficient information.
This also removes the false and useless "ONFI extended param page
detected" debug message (it was printed even on the aforementioned
corruption, and for the success case, we don't really want a print).
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Huang Shijie <b32955@freescale.com>
mtd: atmel_nand: use minimum ecc requirements of nand: ecc_{strength,step}_ds
Since ecc_{strength,step}_ds is introduced in nand_chip structure for
minimum ecc requirements. So we can use them directly and remove our
own get_onfi_ecc_param function.
Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtd: atmel_nand: remove #if defined(CONFIG_OF) around OF-specific code
Since the of specific code are declared in <linux/of_mtd.h> regardless
of CONFIG_OF. Remove the #if defined(CONFIG_OF) guard and use an
IS_ENABLED(CONFIG_OF) instead.
Brian Norris [Tue, 13 Aug 2013 17:51:55 +0000 (10:51 -0700)]
mtd: nand: cleanup ONFI printed errors, warnings
The ONFI detection routine is too verbose in some cases and not verbose
enough in others. This patch refactors it to print only when there are
significant warnings/errors.
Probing in 16-bit mode:
It is unnecessary to print until after the READID (address 20h)
command. READID *has* to work properly in whatever bus width
configuration we are in, or else no identification mode works. So we
can silence some useless warnings on systems which come up in 16-bit
mode and do not even respond with an O-N-F-I string.
Valid parameter page:
Nobody needs to see this. Do we inform the user every time other
hardware responds properly? Instead, add an error message if *no*
uncorrupted parameter pages are found.
ONFI ECC:
Most drivers don't yet use the reported minimum ECC values, so it
shouldn't yet be a fatal condition if the extended parameter page is
incorrect. But we should at least give a warning for the corner cases
that we don't expect.
ONFI flash detected:
Nobody needs to see this. This is the expected case, that we detect
ONFI properly, or else it wasn't ONFI-compliant and is detected by
some other routine.
Brian Norris [Wed, 28 Aug 2013 01:01:19 +0000 (18:01 -0700)]
mtd: onenand: remove unused variable assignments
These variable assignments are never used (the variables are either
never used or are overwritten before use). This resolves some compiler
warnings like the following:
drivers/mtd/onenand/onenand_base.c: In function 'flexonenand_get_boundary':
drivers/mtd/onenand/onenand_base.c:3532:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
drivers/mtd/onenand/onenand_base.c: In function 'onenand_probe':
drivers/mtd/onenand/onenand_base.c:3838:6: warning: variable 'maf_id' set but not used [-Wunused-but-set-variable]
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: Kyungmin Park <kyungmin.park@samsung.com>
Brian Norris [Sat, 10 Aug 2013 08:09:49 +0000 (01:09 -0700)]
mtd: nand: stop exporting nand_default_bbt
I removed the last non-nand_base users of this, and we shouldn't have
any more modules that need to access it. It's only non-static to share
between nand_base and nand_bbt.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver is doing some strange logic here. If it doesn't have
flash-based BBT enabled, it allows nand_scan_tail() to scan the BBT. But
if it is using flash-based BBT, it tells nand_scan_tail() to skip
scanning, then it immediately calls the default BBT scanning function
itself.
As I read it, this logic is equivalent to the default nand_scan_tail()
behavior without interfering with NAND_SKIP_BBTSCAN or calling
nand_default_bbt() directly at all.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Just like the rest of the subsystems, let's add the required no-op
functions to implement stubs when CONFIG_OF=n.
This prevents MTD drivers from having ugly ifdefs in their code,
and instead hide the ifdef monster in the header closet (far away
from people's sight).
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Linus Torvalds [Fri, 25 Oct 2013 19:15:13 +0000 (20:15 +0100)]
Merge tag 'for-linus-20131025' of git://git.infradead.org/linux-mtd
Pull final mtd fixes from Brian Norris:
"A few more last-minute regression fixes, prepared jointly by me and
David Woodhouse:
- Revert pxa3xx to its old name to avoid breaking existing
'mtdparts=' boot strings.
- Return GPMI NAND to its legacy ECC layout for backwards
compatibility. We will revisit this in 3.13.
A note from David on the latter fix: 'This leaves a harmless cosmetic
warning about an unused function. At this point in the cycle I really
don't care.'"
* tag 'for-linus-20131025' of git://git.infradead.org/linux-mtd:
mtd: gpmi: fix ECC regression
mtd: nand: pxa3xx: Fix registered MTD name
Linus Torvalds [Fri, 25 Oct 2013 17:16:47 +0000 (18:16 +0100)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes (try two) from Al Viro:
"nfsd performance regression fix + seq_file lseek(2) fix"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
seq_file: always update file->f_pos in seq_lseek()
nfsd regression since delayed fput()
David Woodhouse [Fri, 25 Oct 2013 14:03:59 +0000 (15:03 +0100)]
mtd: gpmi: fix ECC regression
The "legacy" ECC layout used until 3.12-rc1 uses all the OOB area by
computing the ECC strength and ECC step size ourselves.
Commit 2febcdf84b ("mtd: gpmi: set the BCHs geometry with the ecc info")
makes the driver use the ECC info (ECC strength and ECC step size)
provided by the MTD code, and creates a different NAND ECC layout
for the BCH, and use the new ECC layout. This causes a regression:
We can not mount the ubifs which was created by the old NAND ECC layout.
This patch fixes this issue by reverting to the legacy ECC layout.
We will probably introduce a new device-tree property to indicate that
the new ECC layout can be used. For now though, for the imminent 3.12
release, we just unconditionally revert to the 3.11 behaviour.
This leaves a harmless cosmetic warning about an unused function. At
this point in the cycle I really don't care.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Huang Shijie <b32955@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de>
Gu Zheng [Fri, 25 Oct 2013 10:15:06 +0000 (18:15 +0800)]
seq_file: always update file->f_pos in seq_lseek()
This issue was first pointed out by Jiaxing Wang several months ago, but no
further comments:
https://lkml.org/lkml/2013/6/29/41
As we know pread() does not change f_pos, so after pread(), file->f_pos
and m->read_pos become different. And seq_lseek() does not update file->f_pos
if offset equals to m->read_pos, so after pread() and seq_lseek()(lseek to
m->read_pos), then a subsequent read may read from a wrong position, the
following program produces the problem:
char str1[32] = { 0 };
char str2[32] = { 0 };
int poffset = 10;
int count = 20;
/*open any seq file*/
int fd = open("/proc/modules", O_RDONLY);
Linus Torvalds [Fri, 25 Oct 2013 10:49:23 +0000 (11:49 +0100)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"There's really only one bugfix in this branch, which is a fix for
timers on the integrator platform. Since Linus Walleij is
resurrecting support for the platform it seems valuable to get the fix
into 3.12 even though the regression has been around a while.
The rest are a handful of maintainers updates. If you prefer to hold
those until 3.13 then just merge the first patch on the branch which
is the fix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add maintainers entry for Rockchip SoCs
MAINTAINERS: Tegra updates, and driver ownership
MAINTAINERS: ARM: mvebu: add Sebastian Hesselbarth
ARM: integrator: deactivate timer0 on the Integrator/CP
Linus Torvalds [Fri, 25 Oct 2013 06:32:01 +0000 (07:32 +0100)]
Merge tag 'ecryptfs-3.12-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
"Two important fixes
- Fix long standing memory leak in the (rarely used) public key
support
- Fix large file corruption on 32 bit architectures"
* tag 'ecryptfs-3.12-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: fix 32 bit corruption issue
ecryptfs: Fix memory leakage in keystore.c
There's no advantage in using a hardcoded name for the mtd device.
Instead use the provided by the platform_device.
The MTD name was changed to use the one provided by the platform_device.
However, this can be problematic as some users want to set partitions
using the kernel parameter 'mtdparts', where the name is needed.
Therefore, to avoid regressions in users relying in 'mtdparts' we revert
the change and use the previous one 'pxa3xx_nand-0'.
While at it, let's put a big comment and prevent this change from happening
ever again.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reported-by: Lars Duesing <lars.duesing@camelotsweb.de> Cc: stable@vger.kernel.org # v3.11+ Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Linus Torvalds [Thu, 24 Oct 2013 06:45:34 +0000 (07:45 +0100)]
Merge tag 'md/3.12-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"Assorted md bug-fixes for 3.12.
All tagged for -stable releases too"
* tag 'md/3.12-fixes' of git://neil.brown.name/md:
raid5: avoid finding "discard" stripe
raid5: set bio bi_vcnt 0 for discard request
md: avoid deadlock when md_set_badblocks.
md: Fix skipping recovery for read-only arrays.
Linus Torvalds [Thu, 24 Oct 2013 06:44:47 +0000 (07:44 +0100)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of two fixes which cause oopses (Buslogic, qla2xxx) and
one fix which may cause a hang because of request miscounting (sd)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] sd: call blk_pm_runtime_init before add_disk
[SCSI] qla2xxx: Fix request queue null dereference.
[SCSI] BusLogic: Fix an oops when intializing multimaster adapter
Shaohua Li [Sat, 19 Oct 2013 06:51:42 +0000 (14:51 +0800)]
raid5: avoid finding "discard" stripe
SCSI discard will damage discard stripe bio setting, eg, some fields are
changed. If the stripe is reused very soon, we have wrong bios setting. We
remove discard stripe from hash list, so next time the strip will be fully
initialized.
Suitable for backport to 3.7+.
Cc: <stable@vger.kernel.org> (3.7+) Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
Shaohua Li [Sat, 19 Oct 2013 06:50:28 +0000 (14:50 +0800)]
raid5: set bio bi_vcnt 0 for discard request
SCSI layer will add new payload for discard request. If two bios are merged
to one, the second bio has bi_vcnt 1 which is set in raid5. This will confuse
SCSI and cause oops.
Suitable for backport to 3.7+
Cc: stable@vger.kernel.org (v3.7+) Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de> Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Bian Yu [Sat, 12 Oct 2013 05:10:03 +0000 (01:10 -0400)]
md: avoid deadlock when md_set_badblocks.
When operate harddisk and hit errors, md_set_badblocks is called after
scsi_restart_operations which already disabled the irq. but md_set_badblocks
will call write_sequnlock_irq and enable irq. so softirq can preempt the
current thread and that may cause a deadlock. I think this situation should
use write_sequnlock_irqsave/irqrestore instead.
This bug was introduce in commit 2e8ac30312973dd20e68073653
(the first time rdev_set_badblock was call from interrupt context),
so this patch is appropriate for 3.5 and subsequent kernels.
spares are activated on a read-only array. In case of raid1 and raid10
personalities it causes that not-in-sync devices are marked in-sync
without checking if recovery has been finished.
If a read-only array is degraded and one of its devices is not in-sync
(because the array has been only partially recovered) recovery will be skipped.
This patch adds checking if recovery has been finished before marking a device
in-sync for raid1 and raid10 personalities. In case of raid5 personality
such condition is already present (at raid5.c:6029).
Bug was introduced in 3.10 and causes data corruption.
Let's say the disk_events_workfn() calls sd_check_events() which tries
to send test_unit_ready() and because of sd_revalidate_disk() trying to
send another commands the test_unit_ready() might be re-queued as the
tagged command queuing is disabled.
The problem is, the test_unit_ready request doesn't get counted the
first time it is queued, so the later decrement of q->nr_pending in
blk_pm_requeue_request makes it unbalanced.
Fix this by calling blk_pm_runtime_init before add_disk so that all
requests initiated there will all be counted.
Signed-off-by: Aaron Lu <aaron.lu@intel.com> Reported-and-tested-by: Sujit Reddy Thumma <sthumma@codeaurora.org> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If an invalid IOCB is returned on the response queue then the index into the
request queue map could be invalid and could return to us a bogus value. This
could cause us to try to deference an invalid pointer and cause an exception.
If we encounter this condition, simply return as no context can be established
for this response.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Linus Torvalds [Wed, 23 Oct 2013 07:10:25 +0000 (08:10 +0100)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Several last minute bug fixes.
Two of them are on the larger side for rc7, the dasd format patch for
older storage devices and the store-clock-fast patch where we have
been to optimistic with an optimization"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/time: correct use of store clock fast
s390/vmlogrdr: fix array access in vmlogrdr_open()
s390/compat,signal: fix return value of copy_siginfo_(to|from)_user32()
s390/dasd: check for availability of prefix command during format
s390/mm,kvm: fix software dirty bits vs. kvm for old machines
Linus Torvalds [Wed, 23 Oct 2013 06:58:22 +0000 (07:58 +0100)]
Merge branch 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
"These includes several commits that are necessary to properly fix
regression for TMU test MUX address setting after reset, for exynos
thermal driver.
Specifics:
- fix a regression that the removal of setting a certain field at TMU
configuration setting results in immediately shutdown after reset
on Exynos4412 SoC.
- revert a patch which tries to link the thermal_zone device and its
hwmon node but breaks libsensors.
- fix a deadlock/lockdep warning issue in x86_pkg_temp thermal
driver, which can be reproduced on a buggy platform only.
- fix ti-soc-thermal driver to fall back on bandgap reading when
reading from PCB temperature sensor fails"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Revert "drivers: thermal: parent virtual hwmon with thermal zone"
drivers: thermal: allow ti-soc-thermal run without pcb zone
thermal: exynos: Provide initial setting for TMU's test MUX address at Exynos4412
thermal: exynos: Provide separate TMU data for Exynos4412
thermal: exynos: Remove check for thermal device pointer at exynos_report_trigger()
Thermal: x86_pkg_temp: change spin lock
Linus Torvalds [Wed, 23 Oct 2013 06:52:36 +0000 (07:52 +0100)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- Compilation fixes for GCC < 4.4.6
- one Kbuild dependency select fix (selecting videobuf on msi3101)
- driver fixes on tda10071, e4000, msi3101, soc_camera, s5p-jpeg,
saa7134 and adv7511
- some device quirks needed to make them work properly
- some videobuf2 core regression fixes for some features used only on
embedded drivers
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] saa7134: Fix crash when device is closed before streamoff
[media] adv7511: fix error return code in adv7511_probe()
[media] ths8200: fix compilation with GCC < 4.4.6
[media] ad9389b: fix compilation with GCC < 4.4.6
[media] adv7511: fix compilation with GCC < 4.4.6
[media] adv7842: fix compilation with GCC < 4.4.6
[media] s5p-jpeg: Initialize vfd_decoder->vfl_dir field
[media] videobuf2-dc: Fix support for mappings without struct page in userptr mode
[media] vb2: Allow queuing OUTPUT buffers with zeroed 'bytesused'
[media] mx3-camera: locking cleanup in mx3_videobuf_queue()
[media] sh_vou: almost forever loop in sh_vou_try_fmt_vid_out()
[media] tda10071: change firmware download condition
[media] msi3101: correct max videobuf2 alloc
[media] Add HCL T12Rg-H to STK webcam upside-down table
[media] msi3101: Kconfig select VIDEOBUF2_VMALLOC
[media] msi3101: msi3101_ioctl_ops can be static
[media] e4000: fix PLL calc bug on 32-bit arch
[media] uvcvideo: quirk PROBE_DEF for Microsoft Lifecam NX-3000
[media] uvcvideo: quirk PROBE_DEF for Dell SP2008WFP monitor
Linus Torvalds [Wed, 23 Oct 2013 06:51:25 +0000 (07:51 +0100)]
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband bugfix from Roland Dreier:
"Disable not-quite-ready userspace ABI for IB flow steering"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Temporarily disable create_flow/destroy_flow uverbs
Pull networking fixes from David Miller:
"Sorry I let so much accumulate, I was in Buffalo and wanted a few
things to cook in my tree for a while before sending to you. Anyways,
it's a lot of little things as usual at this stage in the game"
1) Make bonding MAINTAINERS entry reflect reality, from Andy
Gospodarek.
2) Fix accidental sock_put() on timewait mini sockets, from Eric
Dumazet.
3) Fix crashes in l2tp due to mis-handling of ipv4 mapped ipv6
addresses, from François CACHEREUL.
4) Fix heap overflow in __audit_sockaddr(), from the eagle eyed Dan
Carpenter.
5) tcp_shifted_skb() doesn't take handle FINs properly, from Eric
Dumazet.
6) SFC driver bug fixes from Ben Hutchings.
7) Fix TX packet scheduling wedge after channel change in ath9k driver,
from Felix Fietkau.
8) Fix user after free in BPF JIT code, from Alexei Starovoitov.
9) Source address selection test is reversed in
__ip_route_output_key(), fix from Jiri Benc.
10) VLAN and CAN layer mis-size netlink attributes, from Marc
Kleine-Budde.
11) Fix permission checks in sysctls to use current_euid() instead of
current_uid(). From Eric W Biederman.
12) IPSEC policies can go away while a timer is still pending for them,
add appropriate ref-counting to fix, from Steffen Klassert.
13) Fix mis-programming of FDR and RMCR registers on R8A7740 sh_eth
chips, from Nguyen Hong Ky and Simon Horman.
14) MLX4 forgets to DMA unmap pages on RX, fix from Amir Vadai.
15) IPV6 GRE tunnel MTU upper limit is miscalculated, from Oussama
Ghorbel.
16) Fix typo in fq_change(), we were assigning "initial quantum" to
"quantum". From Eric Dumazet.
17) Set a more appropriate sk_pacing_rate for non-TCP sockets, otherwise
FQ packet scheduler does not pace those flows properly. Also from
Eric Dumazet.
18) rtlwifi miscalculates packet pointers, from Mark Cave-Ayland.
19) l2tp_xmit_skb() can be called from process context, not just softirq
context, so we must always make sure to BH disable around it. From
Eric Dumazet.
20) On qdisc reset, we forget to purge the RB tree of SKBs in netem
packet scheduler. From Stephen Hemminger.
21) Fix info leak in farsync WAN driver ioctl() handler, from Dan
Carpenter and Salva Peiró.
22) Fix PHY reset and other issues in dm9000 driver, from Nikita
Kiryanov and Michael Abbott.
23) When hardware can do SCTP crc32 checksums, we accidently don't
disable the csum offload when IPSEC transformations have been
applied. From Fan Du and Vlad Yasevich.
24) Tail loss probing in TCP leaves the socket in the wrong congestion
avoidance state. From Yuchung Cheng.
25) In CPSW driver, enable NAPI before interrupts are turned on, from
Markus Pargmann.
26) Integer underflow and dual-assignment in YAM hamradio driver, from
Dan Carpenter.
27) If we are going to mangle a packet in tcp_set_skb_tso_segs() we must
unclone it. This fixes various hard to track down crashes in
drivers where the SKBs ->gso_segs was changing right from underneath
the driver during TX queueing. From Eric Dumazet.
28) Fix the handling of VLAN IDs, and in particular the special IDs 0
and 4095, in the bridging layer. From Toshiaki Makita.
29) Another info leak, this time in wanxl WAN driver, from Salva Peiró.
30) Fix race in socket credential passing, from Daniel Borkmann.
31) WHen NETLABEL is disabled, we don't validate CIPSO packets properly,
from Seif Mazareeb.
32) Fix identification of fragmented frames in ipv4/ipv6 UDP
Fragmentation Offload output paths, from Jiri Pirko.
33) Virtual Function fixes in bnx2x driver from Yuval Mintz and Ariel
Elior.
34) When we removed the explicit neighbour pointer from ipv6 routes a
slight regression was introduced for users such as IPVS, xt_TEE, and
raw sockets. We mix up the users requested destination address with
the routes assigned nexthop/gateway. From Julian Anastasov and
Simon Horman.
35) Fix stack overruns in rt6_probe(), the issue is that can end up
doing two full packet xmit paths at the same time when emitting
neighbour discovery messages. From Hannes Frederic Sowa.
36) davinci_emac driver doesn't handle IFF_ALLMULTI correctly, from
Mariusz Ceier.
37) Make sure to set TCP sk_pacing_rate after the first legitimate RTT
sample, from Neal Cardwell.
38) Wrong netlink attribute passed to xfrm_replay_verify_len(), from
Steffen Klassert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (152 commits)
ax88179_178a: Add VID:DID for Samsung USB Ethernet Adapter
ax88179_178a: Correct the RX error definition in RX header
Revert "bridge: only expire the mdb entry when query is received"
tcp: initialize passive-side sk_pacing_rate after 3WHS
davinci_emac.c: Fix IFF_ALLMULTI setup
mac802154: correct a typo in ieee802154_alloc_device() prototype
ipv6: probe routes asynchronous in rt6_probe
netfilter: nf_conntrack: fix rt6i_gateway checks for H.323 helper
ipv6: fill rt6i_gateway with nexthop address
ipv6: always prefer rt6i_gateway if present
bnx2x: Set NETIF_F_HIGHDMA unconditionally
bnx2x: Don't pretend during register dump
bnx2x: Lock DMAE when used by statistic flow
bnx2x: Prevent null pointer dereference on error flow
bnx2x: Fix config when SR-IOV and iSCSI are enabled
bnx2x: Fix Coalescing configuration
bnx2x: Unlock VF-PF channel on MAC/VLAN config error
bnx2x: Prevent an illegal pointer dereference during panic
bnx2x: Fix Maximum CoS estimation for VFs
drivers: net: cpsw: fix kernel warn during iperf test with interrupt pacing
...
Linus Lüssing [Sat, 19 Oct 2013 22:58:57 +0000 (00:58 +0200)]
Revert "bridge: only expire the mdb entry when query is received"
While this commit was a good attempt to fix issues occuring when no
multicast querier is present, this commit still has two more issues:
1) There are cases where mdb entries do not expire even if there is a
querier present. The bridge will unnecessarily continue flooding
multicast packets on the according ports.
2) Never removing an mdb entry could be exploited for a Denial of
Service by an attacker on the local link, slowly, but steadily eating up
all memory.
Actually, this commit became obsolete with
"bridge: disable snooping if there is no querier" (b00589af3b)
which included fixes for a few more cases.
Therefore reverting the following commits (the commit stated in the
commit message plus three of its follow up fixes):
CC: Cong Wang <amwang@redhat.com> Signed-off-by: Linus Lüssing <linus.luessing@web.de> Reviewed-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Do not touch keyboard backlight unless explicitly passed a module
parameter. In this way we won't make wrong assumptions about what are
good default values since they actually are different from model to
model.
The only side effect is that we won't know what is the current value
until set via the sysfs attributes.
Randy Dunlap [Sat, 19 Oct 2013 21:57:07 +0000 (14:57 -0700)]
vfs: fix new kernel-doc warnings
Move kernel-doc notation to immediately before its function to eliminate
kernel-doc warnings introduced by commit db14fc3abcd5 ("vfs: add
d_walk()")
Warning(fs/dcache.c:1343): No description found for parameter 'data'
Warning(fs/dcache.c:1343): No description found for parameter 'dentry'
Warning(fs/dcache.c:1343): Excess function parameter 'parent' description in 'check_mount'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Miklos Szeredi <mszeredi@suse.cz> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 22 Oct 2013 09:24:29 +0000 (10:24 +0100)]
Merge tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The pending last-minute ASoC fixes, all of which are driver-local
(tlv320aic3x, rcar, pcm1681, pcm1792a, omap, fsl) and should be pretty
safe to apply"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: Add MAINTAINERS entry for dmaengine helpers
ASoC: pcm1792a: Fix max_register setting
ASoC: pcm1681: Fix max_register setting
ASoC: pcm1681: Fix max_register setting
ASoC: rcar: fixup generation checker
ASoC: tlv320aic3x: Connect 'Left Line1R Mux' and 'Right Line1L Mux'
ASoC: fsl: imx-ssi: fix probe on imx31
ASoC: omap: Fix incorrect ARM dependency
ASoC: fsl: Fix sound on mx31moboard
ASoC: fsl_ssi: Fix irq_of_parse_and_map() return value check
Linus Torvalds [Tue, 22 Oct 2013 07:23:41 +0000 (08:23 +0100)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Travelling slowed down getting these out.
Two vmwgfx fixes, a radeon revert to avoid a regression, i915 fixes,
and some ioctl sizing issues fixed with 32 on 64"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/audio: don't set speaker allocation on DCE4+
drm/radeon: rework audio option
drm/radeon/audio: don't set speaker allocation on DCE3.2
drm/radeon: make missing smc ucode non-fatal (CI)
drm/radeon: make missing smc ucode non-fatal (r7xx-SI)
drm/radeon/uvd: revert lower msg&fb buffer requirements on UVD3
drm/radeon: stop the leaks in cik_ib_test
drm/radeon/atom: workaround vbios bug in transmitter table on rs780
drm/i915: Disable GGTT PTEs on GEN6+ suspend
drm/i915: Make PTE valid encoding optional
drm: Pad drm_mode_get_connector to 64-bit boundary
drm: Prevent overwriting from userspace underallocating core ioctl structs
drm/vmwgfx: Don't kill clients on VT switch
drm/vmwgfx: Don't put resources with invalid id's on lru list
drm/i915: disable LVDS clock gating on CPT v2
Linus Torvalds [Tue, 22 Oct 2013 07:22:40 +0000 (08:22 +0100)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- a partial revert of exponent parsing changes to make "Unit" exponent
item work properly again, by Nikolai Kondrashov
- a few new device IDs additions piggy-backing, by AceLan Kao and David
Herrmann
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wiimote: add LEGO-wiimote VID
HID: Fix unit exponent parsing again
HID: usbhid: quirk for SiS Touchscreen
HID: usbhid: quirk for Synaptics Large Touchccreen
Linus Torvalds [Tue, 22 Oct 2013 07:21:34 +0000 (08:21 +0100)]
Merge branch 'for-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"The only interesting bit is ata_eh_qc_retry() update which fixes a
problem where a SG_IO command may fail across suspend/resume cycle
without the command actually being at fault.
Other changes are low level driver specific and fairly low impact"
* 'for-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libahci: fix turning on LEDs in ahci_start_port()
libata: make ata_eh_qc_retry() bump scmd->allowed on bogus failures
ahci_platform: use dev_info() instead of printk()
ahci: use dev_info() instead of printk()
pata_isapnp: Don't use invalid I/O ports
Linus Torvalds [Tue, 22 Oct 2013 07:20:34 +0000 (08:20 +0100)]
Merge branch 'for-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"Two late fixes for cgroup.
One fixes descendant walk introduced during this rc1 cycle. The other
fixes a post 3.9 bug during task attach which can lead to hang. Both
fixes are critical and the fixes are relatively straight-forward"
* 'for-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fix to break the while loop in cgroup_attach_task() correctly
cgroup: fix cgroup post-order descendant walk of empty subtree
The result of the store-clock-fast (STCKF) instruction is a bit fuzzy.
It can happen that the value stored on one CPU is smaller than the value
stored on another CPU, although the order of the stores is the other
way around. This can cause deltas of get_tod_clock() values to become
negative when they should not be.
We need to be more careful with store-clock-fast, this patch partially
reverts git commit e4b7b4238e666682555461fa52eecd74652f36bb "time:
always use stckf instead of stck if available". The get_tod_clock()
function now uses the store-clock-extended (STCKE) instruction.
get_tod_clock_fast() can be used if the fuzziness of store-clock-fast
is acceptable e.g. for wait loops local to a CPU.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Dave Airlie [Tue, 22 Oct 2013 06:35:17 +0000 (07:35 +0100)]
Merge branch 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Most just regression fixes for audio, dpm, and uvd, plus
a resource leak fix for cik.
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/audio: don't set speaker allocation on DCE4+
drm/radeon: rework audio option
drm/radeon/audio: don't set speaker allocation on DCE3.2
drm/radeon: make missing smc ucode non-fatal (CI)
drm/radeon: make missing smc ucode non-fatal (r7xx-SI)
drm/radeon/uvd: revert lower msg&fb buffer requirements on UVD3
drm/radeon: stop the leaks in cik_ib_test
drm/radeon/atom: workaround vbios bug in transmitter table on rs780
Dave Airlie [Tue, 22 Oct 2013 06:32:40 +0000 (07:32 +0100)]
Merge tag 'drm-intel-fixes-2013-10-21' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Just an lvds clock gating fix and a pte clearing hack for hsw to avoid
memory corruption when hibernating - something doesn't seem to switch off
properly, we're still investigating.
* tag 'drm-intel-fixes-2013-10-21' of git://people.freedesktop.org/~danvet/drm-intel: (96 commits)
drm/i915: Disable GGTT PTEs on GEN6+ suspend
drm/i915: Make PTE valid encoding optional
drm/i915: disable LVDS clock gating on CPT v2
Neal Cardwell [Mon, 21 Oct 2013 19:40:19 +0000 (15:40 -0400)]
tcp: initialize passive-side sk_pacing_rate after 3WHS
For passive TCP connections, upon receiving the ACK that completes the
3WHS, make sure we set our pacing rate after we get our first RTT
sample.
On passive TCP connections, when we receive the ACK completing the
3WHS we do not take an RTT sample in tcp_ack(), but rather in
tcp_synack_rtt_meas(). So upon receiving the ACK that completes the
3WHS, tcp_ack() leaves sk_pacing_rate at its initial value.
Originally the initial sk_pacing_rate value was 0, so passive-side
connections defaulted to sysctl_tcp_min_tso_segs (2 segs) in skbuffs
made in the first RTT. With a default initial cwnd of 10 packets, this
happened to be correct for RTTs 5ms or bigger, so it was hard to
see problems in WAN or emulated WAN testing.
Since 7eec4174ff ("pkt_sched: fq: fix non TCP flows pacing"), the
initial sk_pacing_rate is 0xffffffff. So after that change, passive
TCP connections were keeping this value (and using large numbers of
segments per skbuff) until receiving an ACK for data.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mariusz Ceier [Mon, 21 Oct 2013 17:45:04 +0000 (19:45 +0200)]
davinci_emac.c: Fix IFF_ALLMULTI setup
When IFF_ALLMULTI flag is set on interface and IFF_PROMISC isn't,
emac_dev_mcast_set should only enable RX of multicasts and reset
MACHASH registers.
It does this, but afterwards it either sets up multicast MACs
filtering or disables RX of multicasts and resets MACHASH registers
again, rendering IFF_ALLMULTI flag useless.
This patch fixes emac_dev_mcast_set, so that multicast MACs filtering and
disabling of RX of multicasts are skipped when IFF_ALLMULTI flag is set.
Tested with kernel 2.6.37.
Signed-off-by: Mariusz Ceier <mceier+kernel@gmail.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Routes need to be probed asynchronous otherwise the call stack gets
exhausted when the kernel attemps to deliver another skb inline, like
e.g. xt_TEE does, and we probe at the same time.
We update neigh->updated still at once, otherwise we would send to
many probes.
Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 21 Oct 2013 22:39:36 +0000 (18:39 -0400)]
Merge branch 'rt6i_gateway'
Julian Anastasov says:
====================
ipv6: use rt6i_gateway as nexthop
The following patchset makes sure that rt6i_gateway
contains valid nexthop information in all cases, so that
we can use different nexthop for sending.
The first patch is a simple fix that makes IPVS, TEE,
RAW(hdrincl) and RTF_DYNAMIC(without RTF_GATEWAY) work as
before 3.9. There is a single corner case not solved by
this patch: RAW(hdrincl) or TEE using local address for
nexthop, a silly feature, I guess. In this case we
see zeroes in rt6i_gateway because we get route that is not
cloned. This is solved only with patch 2.
The second patch is an optimization that makes sure
all resulting routes have rt6i_gateway filled, so that we
can avoid the complex ipv6_addr_any() call added to rt6_nexthop()
by patch 1. And it sets rt6i_gateway for local routes, a case
not handled by patch 1.
The third patch uses the new rt6_nexthop() function to fix
the matching of gateways in the same way as commit bbb5823cf742a7
("netfilter: nf_conntrack: fix rt_gateway checks for H.323 helper")
fixes nf_conntrack_h323_main.c for IPv4. Currently, it depends on
the new definition of rt6_nexthop() in patch 2. Actually, if
patch 2 is applied, patch 3 becomes a cosmetic change.
I see the following two alternatives for applying these
patches:
1. Linger patch 2 in net-next to avoid surprises in the upcoming
release. In this case patch 3 can be reworked not to depend on
the new rt6_nexthop() definition in patch 2. I guess this is a
better option, so that patch 2 can be reviewed and tested for
longer time.
2. Include all 3 patches in net tree - more risky because this
is my first attempt to change IPv6.
Here is the situation as handled by patch 2:
In IPv6 the resolved routes are always host routes (/128
with DST_HOST), mostly cloned ones. We allow routes in FIB
to contain rt6i_gateway with zeroes (eg. for local subnets) but
on cloning we can fill the rt6i_gateway field in result.
This works even without this patchset.
There is a single special case where dst is provided as
skb_dst directly without a routing call: icmp6_dst_alloc(). It is a
private dst allocated just for the particular ICMP packet. Patch 2
fills rt6i_gateway in this case, needed for the new rt6_nexthop()
simplification.
The last case is addrconf_dst_alloc(), it can put in
FIB local/anycast routes when addresses are added. Patch 2
needs to fill rt6i_gateway in this case because such routes
are returned without cloning.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Sun, 20 Oct 2013 12:43:05 +0000 (15:43 +0300)]
netfilter: nf_conntrack: fix rt6i_gateway checks for H.323 helper
Now when rt6_nexthop() can return nexthop address we can use it
for proper nexthop comparison of directly connected destinations.
For more information refer to commit bbb5823cf742a7
("netfilter: nf_conntrack: fix rt_gateway checks for H.323 helper").
Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Sun, 20 Oct 2013 12:43:04 +0000 (15:43 +0300)]
ipv6: fill rt6i_gateway with nexthop address
Make sure rt6i_gateway contains nexthop information in
all routes returned from lookup or when routes are directly
attached to skb for generated ICMP packets.
The effect of this patch should be a faster version of
rt6_nexthop() and the consideration of local addresses as
nexthop.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log