Sebastien Dugué [Sat, 30 Dec 2006 00:46:53 +0000 (16:46 -0800)]
[PATCH] Fix IPMI watchdog set_param_str() using kstrdup
set_param_str() cannot use kstrdup() to duplicate the parameter. That's
fine when the driver is compiled as a module but it sure is not when built
into the kernel as the kernel parameters are parsed before the kmalloc
slabs are setup.
Linus Torvalds [Fri, 29 Dec 2006 18:06:41 +0000 (10:06 -0800)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (28 commits)
V4L/DVB (5010): Cx88: Fix leadtek_eeprom tagging
V4L/DVB (5012): Usbvision fix: It was using "&&" instead "&"
V4L/DVB (5001): Add two required headers on kernel 2.6.20-rc1
V4L/DVB (5014): Allyesconfig build fixes on some non x86 arch
V4L/DVB (4997): Bttv: delete duplicated ioremap()
V4L/DVB (4996): Msp3400: fix kthread_run error check
V4L/DVB (4995): Vivi: fix kthread_run() error check
V4L/DVB (4994): Vivi: fix use after free in list_for_each()
V4L/DVB (4992): Fix typo in saa7134-dvb.c
V4L/DVB (4991): Cafe_ccic.c: fix NULL dereference
V4L/DVB (4990): Cpia2/cpia2_usb.c: fix error-path leak
V4L/DVB (4988): Cx2341x audio_properties is an u16, not u8
V4L/DVB (4984): LOG_STATUS should show the real temporal filter value.
V4L/DVB (4983): Force temporal filter to 0 when scaling to prevent ghosting.
V4L/DVB (4982): Fix broken audio mode handling for line-in in msp3400.
V4L/DVB (4980): Fixes bug 7267: PAL/60 is not working
V4L/DVB (4979): Fixes compilation when CONFIG_V4L1_COMPAT is not selected
V4L/DVB (4973): Dvb-core: fix printk type warning
V4L/DVB (4972): Dvb-core: fix bug in CRC-32 checking on 64-bit systems
V4L/DVB (4970): Usbvision memory fixes
...
Linus Torvalds [Fri, 29 Dec 2006 18:03:54 +0000 (10:03 -0800)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (42 commits)
r8169: extraneous Cmd{Tx/Rx}Enb write
forcedeth: modified comment header
NetXen: Reducing ring sizes for IOMMU issue.
NetXen: Fix for PPC machines.
NetXen: work queue fixes.
NetXen: Link status message correction for quad port cards.
NetXen: Multiple adapter fix.
NetXen: Using correct CHECKSUM flag.
NetXen: driver reload fix for newer firmware.
NetXen: Adding new device ids.
PHY probe not working properly for ibm_emac (PPC4xx)
ep93xx: some minor cleanups to the ep93xx eth driver
sky2: phy power down needs PCI config write enabled
sky2: power management/MSI workaround
sky2: dual port NAPI problem
via-velocity uses INET interfaces
e1000: Do not truncate TSO TCP header with 82544 workaround
myri10ge: handle failures in suspend and resume
myri10ge: no need to save MSI and PCIe state in the driver
myri10ge: make msi configurable at runtime through sysfs
...
Linus Torvalds [Fri, 29 Dec 2006 18:00:58 +0000 (10:00 -0800)]
VM: Fix nasty and subtle race in shared mmap'ed page writeback
The VM layer (on the face of it, fairly reasonably) expected that when
it does a ->writepage() call to the filesystem, it would write out the
full page at that point in time. Especially since it had earlier marked
the whole page dirty with "set_page_dirty()".
But that isn't actually the case: ->writepage() does not actually write
a page, it writes the parts of the page that have been explicitly marked
dirty before, *and* that had not got written out for other reasons since
the last time we told it they were dirty.
That last caveat is the important one.
Which _most_ of the time ends up being the whole page (since we had
called "set_page_dirty()" on the page earlier), but if the filesystem
had done any dirty flushing of its own (for example, to honor some
internal write ordering guarantees), it might end up doing only a
partial page IO (or none at all) when ->writepage() is actually called.
That is the correct thing in general (since we actually often _want_
only the known-dirty parts of the page to be written out), but the
shared dirty page handling had implicitly forgotten about these details,
and had a number of cases where it was doing just the "->writepage()"
part, without telling the low-level filesystem that the whole page might
have been re-dirtied as part of being mapped writably into user space.
Since most of the time the FS did actually write out the full page, we
didn't notice this for a loong time, and this needed some really odd
patterns to trigger. But it caused occasional corruption with rtorrent
and with the Debian "apt" database, because both use shared mmaps to
update the end result.
This fixes it. Finally. After way too much hair-pulling.
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au> Acked-by: Martin J. Bligh <mbligh@google.com> Acked-by: Martin Michlmayr <tbm@cyrius.com> Acked-by: Martin Johansson <martin@fatbob.nu> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Andrei Popa <andrei.popa@i-neo.ro> Cc: High Dickins <hugh@veritas.com> Cc: Andrew Morton <akpm@osdl.org>, Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Segher Boessenkool <segher@kernel.crashing.org> Cc: David Miller <davem@davemloft.net> Cc: Arjan van de Ven <arjan@infradead.org> Cc: Gordon Farquharson <gordonfarquharson@gmail.com> Cc: Guillaume Chazarain <guichaz@yahoo.fr> Cc: Theodore Tso <tytso@mit.edu> Cc: Kenneth Cheng <kenneth.w.chen@intel.com> Cc: Tobias Diedrich <ranma@tdiedrich.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Michael Holzheu [Wed, 27 Dec 2006 23:35:36 +0000 (00:35 +0100)]
[S390] cio: fix stsch_reset.
Copy inline assembly of stsch and add "memory" to clobber list in order
to prevent gcc from optimizing away the checking of the global variable
"pgm_check_occured".
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Jean Delvare [Sat, 23 Dec 2006 17:11:03 +0000 (14:11 -0300)]
V4L/DVB (5010): Cx88: Fix leadtek_eeprom tagging
reference to .init.text: from .text between 'cx88_card_setup'
(at offset 0x68c) and 'cx88_risc_field'
Caused by leadtek_eeprom() being declared __devinit and called from
a non-devinit context.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (5001): Add two required headers on kernel 2.6.20-rc1
include/media/ir-common.h:78: error: field 'work' has incomplete type
drivers/media/common/ir-functions.c: In function 'ir_rc5_timer_end':
drivers/media/common/ir-functions.c:301: error: 'jiffies' undeclared (first use in this function)
drivers/media/common/ir-functions.c:301: error: (Each undeclared identifier is reported only once)
drivers/media/common/ir-functions.c:301: error: for each function it appears in.)
drivers/media/common/ir-functions.c:347: error: 'HZ' undeclared (first use in this function)
David Brownell [Wed, 27 Dec 2006 12:53:44 +0000 (09:53 -0300)]
V4L/DVB (5014): Allyesconfig build fixes on some non x86 arch
- CAFE_CCIC needs to depend on PCI, else "allyesconfig" breaks
on systems without PCI
- em28xx-video can't udelay(2500) else "allyesconfig" breaks
on systems that refuse to spin that long (I saw it on ARM)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Mon, 18 Dec 2006 16:40:23 +0000 (13:40 -0300)]
V4L/DVB (4984): LOG_STATUS should show the real temporal filter value.
The temporal filter is forced off when scaling. The VIDIOC_LOG_STATUS
handler still showed the old temporal filter. It is now consistent with
the real temporal filter value.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Mon, 18 Dec 2006 16:37:50 +0000 (13:37 -0300)]
V4L/DVB (4983): Force temporal filter to 0 when scaling to prevent ghosting.
Change the code to unconditionally turn off the temporal filter when scaling.
If the window is not full screen the filter will introduce a nasty ghosting
effect.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Mon, 18 Dec 2006 16:18:28 +0000 (13:18 -0300)]
V4L/DVB (4982): Fix broken audio mode handling for line-in in msp3400.
The wrong matrix was used when an external input was selected instead of
the tuner input. The rxsubchans field was also not initialized to STEREO
for an external input. And finally the msp34xxg_detect_stereo() should
not try to detect stereo for an external input, that code is for the
tuner input only.
Together these bugs made it hit 'n miss whether you ever got stereo out
of the msp3400 for an external input.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (4980): Fixes bug 7267: PAL/60 is not working
On cx88 driver, sampling rate should be at chroma subcarrier freq (FSC).
However, driver were programming wrong values for PAL/60, PAL/Nc and
NTSC 4.43. This patch do the proper calculation. It also calculates
htotal, hdelay and hactive constants, according with the sampling
rate.
It is tested with PAL/60 by Piotr Maksymuk and Olivier. Also tested with
the already-supported standards.
Dwaine Garden [Wed, 27 Dec 2006 12:23:28 +0000 (10:23 -0200)]
V4L/DVB (4979): Fixes compilation when CONFIG_V4L1_COMPAT is not selected
- SYSFS: Replaced all to_video_device(cd), video_device_create_file,
video_device_remove_file and add the proper checks at create_file
- Converted old norm values to V4L2 ones.
- Robustness on sysfs hue/contrast/saturation queries.
Additional check in order to return 0 if the driver is not opened.
- Whitespace cleanups in usbvision-cards.c
This patch merges two fixes by Thierry MERLE and Mauro Chehab, and adds
additional checks.
Michael Krufky [Thu, 14 Dec 2006 16:53:33 +0000 (13:53 -0300)]
V4L/DVB (4973): Dvb-core: fix printk type warning
dvb_net.c: In function 'dvb_net_ule':
dvb_net.c:628: warning: format '%#lx' expects type 'long unsigned int', but argument 3 has type 'u32'
dvb_net.c:628: warning: format '%#lx' expects type 'long unsigned int', but argument 4 has type 'u32'
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ang Way Chuang [Thu, 14 Dec 2006 16:51:44 +0000 (13:51 -0300)]
V4L/DVB (4972): Dvb-core: fix bug in CRC-32 checking on 64-bit systems
CRC-32 checking during ULE decapsulation always failed on x86_64 systems due
to the size of a variable used to store CRC. This bug was discovered on
Fedora Core 6 with kernel-2.6.18-1.2849. The i386 counterpart has no such
problem. This patch has been tested on 64-bit system as well as 32-bit system.
Signed-off-by: Ang Way Chuang <wcang@nrg.cs.usm.my> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thierry MERLE [Fri, 15 Dec 2006 19:46:53 +0000 (16:46 -0300)]
V4L/DVB (4970): Usbvision memory fixes
- fix decompression buffer allocation not done at first driver open
- simplification of USB sbuf allocation (use of usb_buffer_alloc)
- replaced vmalloc by vmalloc_32 (for homogeneity)
- add of saa7111 (i2cAddr=0x48) detection printout in attach_inform
V4L/DVB (4960): Removal of unused code from usbvision-i2c.c
i2c_adap is almost not used. This patch removes it, cleaning the i2c support,
and improving driver understanding.
Thanks to Thierry Merle for testing it.
Ralf Baechle [Mon, 11 Dec 2006 14:14:54 +0000 (11:14 -0300)]
V4L/DVB (4958): Fix namespace conflict between w9968cf.c on MIPS
Both use __SC. Since __* is sort of private namespace I've choosen to fix
this in the driver. For consistency I decieded to also change __UNSC to
UNSC.
Amit S. Kale [Mon, 18 Dec 2006 13:54:36 +0000 (05:54 -0800)]
NetXen: Reducing ring sizes for IOMMU issue.
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic.h | 10 +++++-----
1 files changed, 5 insertions(+), 5 deletions(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
Amit S. Kale [Mon, 18 Dec 2006 13:53:12 +0000 (05:53 -0800)]
NetXen: Link status message correction for quad port cards.
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_isr.c | 3 ++-
1 files changed, 2 insertions(+), 1 deletion(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
Amit S. Kale [Mon, 18 Dec 2006 13:51:58 +0000 (05:51 -0800)]
NetXen: Using correct CHECKSUM flag.
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_hw.c | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
Amit S. Kale [Mon, 18 Dec 2006 13:51:29 +0000 (05:51 -0800)]
NetXen: driver reload fix for newer firmware.
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_main.c | 7 +++++++
1 files changed, 7 insertions(+) Signed-off-by: Jeff Garzik <jeff@garzik.org>
Amit S. Kale [Mon, 18 Dec 2006 13:50:59 +0000 (05:50 -0800)]
NetXen: Adding new device ids.
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_main.c | 2 ++
1 files changed, 2 insertions(+) Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hynek Petrak [Tue, 19 Dec 2006 21:08:49 +0000 (13:08 -0800)]
PHY probe not working properly for ibm_emac (PPC4xx)
I have a system with AMCC PowerPC 405EP and PHY Intel LXT971A. Linux
2.6.18.3 is not able to detect the PHY ID correctly. The PHY ID
detected is 0, but should be 0x1d.
This is because phy_read() (__emac_mdio_read() resp.) from
drivers/net/ibm_emac/ibm_emac_core.c might return -ETIMEDOUT or
-EREMOTEIO on error. This is ignored inside the
int mii_phy_probe(struct mii_phy *phy, int address)
from drivers/net/ibm_emac/ibm_emac_phy.c
as the return value is assigned to an u32 variable.
Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Yan Burman [Tue, 19 Dec 2006 21:08:48 +0000 (13:08 -0800)]
ep93xx: some minor cleanups to the ep93xx eth driver
Small cleanup in the Cirrus Logic EP93xx ethernet driver: Check for NULL
pointer before dereferencing it instead of after. Remove unreferenced
variable.
Signed-off-by: Yan Burman <burman.yan@gmail.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
sky2: phy power down needs PCI config write enabled
In order to change PCI registers (via the iomap'd window),
it needs to be enabled; this wasn't being done in sky2_phy_power
the function that turns on/off power to the PHY.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
MSI doesn't work properly on resume on many platforms because the
BIOS goes and changes it back to INTx mode after the sky2 driver has
restored in resume.
It is really a bug in the base power management resume code, and
this workaround is temporary until the change to PM code works it's way
through the release process. The PM fix is non-trivial since it needs
to change when non-boot CPU's are enabled.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Shutting down port 0 disables the NAPI poll used by both ports.
The long term fix will be to separate NAPI object from net device
until then just reenable if needed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Randy Dunlap [Tue, 19 Dec 2006 05:21:10 +0000 (21:21 -0800)]
via-velocity uses INET interfaces
via-velocity doesn't build when CONFIG_INET=n:
drivers/built-in.o: In function `velocity_unregister_notifier':
via-velocity.c:(.text+0xe9b46): undefined reference to `unregister_inetaddr_notifier'
drivers/built-in.o: In function `velocity_init_module':
via-velocity.c:(.init.text+0xa027): undefined reference to `register_inetaddr_notifier'
I wanted to make this change in drivers/net/Kconfig, but
this isn't legal kconfig language:
config VIA_VELOCITY
tristate "VIA Velocity support"
depends on NET_PCI && PCI
+ depends on INET if PM
select CRC32
select CRC_CCITT
select MII
so fix it in via-velocity.c instead.
Builds with all 4 combinations of CONFIG_NET & CONFIG_PM.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Herbert Xu [Sat, 16 Dec 2006 01:04:33 +0000 (12:04 +1100)]
e1000: Do not truncate TSO TCP header with 82544 workaround
The e1000 driver has a workaround for 82544 on PCI-X where if the
terminating byte of a buffer is at addresses 0-3 mod 8, then 4 bytes
are shaved off it and defered to a new segment. This is due to an
erratum that could otherwise cause TX hangs.
Unfortunately this breaks TSO because it may cause the TCP header to
be split over two segments which itself causes TX hangs. The solution
is to pull 4 bytes of data up from the next segment rather than pushing
4 bytes off. This ensures the TCP header remains in one piece and
works around the PCI-X hang.
This patch is based on one from Jesse Brandeburg.
This bug has been trigered by both CONFIG_DEBUG_SLAB as well as Xen.
Note that the only reason we don't see this normally is because the
TCP stack starts writing from the end, i.e., it writes the TCP header
first then slaps on the IP header, etc. So the end of the TCP header
(skb->tail - 1 here) is always aligned correctly.
Had we made the start of the IP header (e.g., IPv6) 8-byte aligned
instead, this would happen for normal TCP traffic as well.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
--
Visit Openswan at http://www.openswan.org/
Email: Herbert Xu ~{PmV>HI~} <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt
-- Signed-off-by: Jeff Garzik <jeff@garzik.org>
Brice Goglin [Mon, 18 Dec 2006 10:52:02 +0000 (11:52 +0100)]
myri10ge: no need to save MSI and PCIe state in the driver
The PCI MSI and express state are already saved and restored by the
current versions of pci_save_state/pci_restore_state.
Therefore it is no longer necessary for the driver to do it.
Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Brice Goglin [Mon, 18 Dec 2006 10:50:40 +0000 (11:50 +0100)]
myri10ge: move request_irq to myri10ge_open
Request IRQ in myri10ge_open() and free in close() instead of probe()
and remove() to eliminate potential race between the watchdog and the
interrupt handler. Additionaly, the interrupt handler won't get called
on shared irq anymore when the interface is down.
Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Brice Goglin [Mon, 18 Dec 2006 10:50:00 +0000 (11:50 +0100)]
myri10ge: match number of save_state and restore
Since pci_save_state() pushes MSI and PCIe states on a kind of stack,
myri10ge saving the state in advance for parity recovery will push the
state again on the stack on suspend. This leads to some memory leak.
We add a couple additional calls to save_state and restore_state so
that we don't leak anymore.
For the future, we are thinking of a better way to recover from parity
error without using pci_save_state().
Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Francois Romieu [Sun, 17 Dec 2006 22:03:15 +0000 (23:03 +0100)]
netpoll: drivers must not enable IRQ unconditionally in their NAPI handler
net/core/netpoll.c::netpoll_send_skb() calls the poll handler when
it is available. As netconsole can be used from almost any context,
IRQ must not be enabled blindly in the NAPI handler of a driver which
supports netpoll.
The netxen driver includes a private ioctl that provides access
to functionality that is already available in other ways. The PCI
layer has application access hooks (see setpci), and the statistics
are available in ethtool/netstats.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jesse Brandeburg [Fri, 15 Dec 2006 09:42:34 +0000 (10:42 +0100)]
[PATCH] e1000: No-delay link detection at interface up
Currently after an interface up, the link state is detected 2 seconds later
when the first watchdog timer runs. This patch changes that by triggering
the hardware to generate a link-change interrupt from the up() function
instead. This has the result that the link state gets detected immediately
and without races. This has the potential to speed up booting since a normal
distribution boot process waits for a link before DHCP is attempted.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jesse Brandeburg [Fri, 15 Dec 2006 09:40:39 +0000 (10:40 +0100)]
[PATCH] e1000: Make the copybreak value a module parameter
Allow the user to vary the size that copybreak works. Currently cb is enabled
for packets < 256 bytes, but various tests indicate that this should be
configurable for specific use cases. In addition, this parameter allows us
to force never/always during testing to get full and predictable coverage of
both code paths.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bruce Allan [Fri, 15 Dec 2006 09:39:45 +0000 (10:39 +0100)]
[PATCH] e1000: Fix PBA allocation calculations
Assign the PBA to be large enough to contain at least 2 jumbo frames on
all adapters. This dramatically increases performance on several adapters
and fixes TX performance degradation issues where the PBA was misallocated
in the old algorithm.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jesse Brandeburg [Fri, 15 Dec 2006 09:38:32 +0000 (10:38 +0100)]
[PATCH] e1000: narrow down the scope of the tipg timer tweak
the driver has (ancient) code for messing with TIPG from the 82542 days.
Unfortunately this code was running on our current adapters and setting
TIPG for fiber to be +1 over the copper value. This caused 1.45Mpps
to be sent instead of 1.487Mpps.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff Kirsher [Fri, 15 Dec 2006 09:37:32 +0000 (10:37 +0100)]
[PATCH] e1000: fix ethtool reported bus type for older adapters
For older adapters we know that they are of the PCI bus type, so we can
just set this.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bruce Allan [Fri, 15 Dec 2006 09:36:35 +0000 (10:36 +0100)]
[PATCH] e1000: fix to set the new max frame size before resetting the adapter
This bugfix makes sure that the driver data reflects the full new situation
before the adapter is reinitialized.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jesse Brandeburg [Fri, 15 Dec 2006 09:34:46 +0000 (10:34 +0100)]
[PATCH] e1000: disable TSO on the 82544 with slab debugging
CONFIG_DEBUG_SLAB changes alignments of the data structures the slab
allocators return. These break certain workarounds for TSO on the 82544.
Since DEBUG_SLAB is relatively rare and not used for performance sensitive
cases, the simplest fix is to disable TSO in this special situation.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jesse Brandeburg [Fri, 15 Dec 2006 09:33:46 +0000 (10:33 +0100)]
[PATCH] e1000: Fix Wake-on-Lan with forced gigabit speed
If the user has forced gigabit speed, phy power management must be disabled;
otherwise the NIC would try to negotiate to a linkspeed of 10/100 mbit on
shutdown, which would lead to a total loss of link. This loss of link breaks
Wake-on-Lan and IPMI.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several bugs existed in how we handle manageability issues all
over the driver. This patch consolidates all the managability
release and init code in two single functions and call them from
appropriate locations. This fixes several BMC packet redirect issues
and powerup/down hiccups.
Originally from Jesse Brandeburg <jesse.brandeburg@intel.com>, rewritten
to use feature flags by me.
Jesse Brandeburg [Fri, 15 Dec 2006 09:30:44 +0000 (10:30 +0100)]
[PATCH] e1000: dynamic itr: take TSO and jumbo into account
The dynamic interrupt rate control patches omitted proper counting
for jumbo's and TSO resulting in suboptimal interrupt mitigation strategies.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jesse Brandeburg [Fri, 15 Dec 2006 09:29:31 +0000 (10:29 +0100)]
[PATCH] e1000: The user-supplied itr setting needs the lower 2 bits masked off
The lower 2 bits of a user-supplied itr setting (via ethtool) need to be
masked off: These lower two bits are used as control bits.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
OGAWA Hirofumi [Sat, 23 Dec 2006 01:00:43 +0000 (10:00 +0900)]
[PATCH] arch/i386/pci/mmconfig.c tlb flush fix
We use the fixmap for accessing pci config space in pci_mmcfg_read/write().
The problem is in pci_exp_set_dev_base(). It is caching a last
accessed address to avoid calling set_fixmap_nocache() whenever
pci_mmcfg_read/write() is used.
But if cpus accessed the above order, the second pci_mmcfg_read() on
cpu0 doesn't flush the TLB, because "mmcfg_last_accessed_device" is
device-B. So, second pci_mmcfg_read() on cpu0 accesses a device-A via
a previous TLB cache. This problem became the cause of several strange
behavior.
This patches fixes this situation by adds "mmcfg_last_accessed_cpu" check.
[ Alternatively, we could make a per-cpu mapping area or something. Not
that it's probably worth it, but if we wanted to avoid all locking and
instead just disable preemption, that would be the way to go. --Linus ]
Linus Torvalds [Sat, 23 Dec 2006 17:25:04 +0000 (09:25 -0800)]
Clean up and export cancel_dirty_page() to modules
Make cancel_dirty_page() act more like all the other dirty and writeback
accounting functions: test for "mapping" being NULL, and do the
NR_FILE_DIRY accounting purely based on mapping_cap_account_dirty()).
Also, add it to the exports, so that modular filesystems can use it.
Acked-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus Torvalds [Sat, 23 Dec 2006 02:46:56 +0000 (18:46 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (68 commits)
ACPI: replace kmalloc+memset with kzalloc
ACPI: Add support for acpi_load_table/acpi_unload_table_id
fbdev: update after backlight argument change
ACPI: video: Add dev argument for backlight_device_register
ACPI: Implement acpi_video_get_next_level()
ACPI: Kconfig - depend on PM rather than selecting it
ACPI: fix NULL check in drivers/acpi/osl.c
ACPI: make drivers/acpi/ec.c:ec_ecdt static
ACPI: prevent processor module from loading on failures
ACPI: fix single linked list manipulation
ACPI: ibm_acpi: allow clean removal
ACPI: fix git automerge failure
ACPI: ibm_acpi: respond to workqueue update
ACPI: dock: add uevent to indicate change in device status
ACPI: ec: Lindent once again
ACPI: ec: Change #define to enums there possible.
ACPI: ec: Style changes.
ACPI: ec: Acquire Global Lock under EC mutex.
ACPI: ec: Drop udelay() from poll mode. Loop by reading status field instead.
ACPI: ec: Rename gpe_bit to gpe
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[UDP]: Fix reversed logic in udp_get_port().
[IPV6]: Dumb typo in generic csum_ipv6_magic()
[SCTP]: make 2 functions static
[SCTP]: Fix typo adaption -> adaptation as per the latest API draft.
[SCTP]: Don't export include/linux/sctp.h to userspace.
[TCP]: Fix ambiguity in the `before' relation.
[ATM] drivers/atm/fore200e.c: Cleanups.
[ATM]: Remove dead ATM_TNETA1570 option.
NetLabel: correctly fill in unused CIPSOv4 level and category mappings
NetLabel: perform input validation earlier on CIPSOv4 DOI add ops
Jens Axboe [Fri, 22 Dec 2006 08:38:53 +0000 (09:38 +0100)]
[PATCH] cfq-iosched: tighten allow merge criteria
The logic in cfq_allow_merge() wasn't clear enough - basically allow
merging for the same queues only. Do a fast check for 'rq and bio both
sync/async' before doing the cfqq hash lookup.
[SCTP]: Fix typo adaption -> adaptation as per the latest API draft.
Signed-off-by: Ivan Skytte Jorgensen <isj-sctp@i1.dk> Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Problem: This definition suffers from an an ambiguity, i.e. always
before(a, (a + 2^31) % 2^32)) = 1
before((a + 2^31) % 2^32), a) = 1
In text: when the difference between a and b amounts to 2^31,
a is always considered `before' b, the function can not decide.
The reason is that implicitly 0 is `before' 1 ... 2^31-1 ... 2^31
Solution: There is a simple fix, by defining before in such a way that
0 is no longer `before' 2^31, i.e. 0 `before' 1 ... 2^31-1
By not using the middle between 0 and 2^32, before can be made
unambiguous.
This is achieved by testing whether seq2-seq1 > 0 (using signed
32-bit arithmetic).
I attach a patch to codify this. Also the `after' relation is basically
a redefinition of `before', it is now defined as a macro after before.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Adrian Bunk [Wed, 20 Dec 2006 03:36:32 +0000 (19:36 -0800)]
[ATM] drivers/atm/fore200e.c: Cleanups.
This patch contains the following transformations from custom functions
to standard kernel version:
- fore200e_kmalloc() -> kzalloc()
- fore200e_kfree() -> kfree()
- fore200e_swap() -> cpu_to_be32()
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Fri, 15 Dec 2006 21:49:28 +0000 (16:49 -0500)]
NetLabel: correctly fill in unused CIPSOv4 level and category mappings
Back when the original NetLabel patches were being changed to use Netlink
attributes correctly some code was accidentially dropped which set all of the
undefined CIPSOv4 level and category mappings to a sentinel value. The result
is the mappings data in the kernel contains bogus mappings which always map to
zero. This patch restores the old/correct behavior by initializing the mapping
data to the correct sentinel value.
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: James Morris <jmorris@namei.org>
Paul Moore [Fri, 15 Dec 2006 21:49:27 +0000 (16:49 -0500)]
NetLabel: perform input validation earlier on CIPSOv4 DOI add ops
There are a couple of cases where the user input for a CIPSOv4 DOI add
operation was not being done soon enough; the result was unexpected behavior
which was resulting in oops/panics/lockups on some platforms. This patch moves
the existing input validation code earlier in the code path to protect against
bogus user input.
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: James Morris <jmorris@namei.org>
[PATCH] Fix reparenting to the same thread group. (take 2)
This patch fixes the case when we reparent to a different thread in the
same thread group. This modifies the code so that we do not send
signals and do not change the signal to send to SIGCHLD unless we have
change the thread group of our parents. It also suppresses sending
pdeath_sig in this cas as well since the result of geppid doesn't
change.
Thanks to Oleg for spotting my bug of only fixing this for non-ptraced
tasks.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Albert Cahalan <acahalan@gmail.com> Cc: Andrew Morton <akpm@osdl.org> Cc: Roland McGrath <roland@redhat.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Coywolf Qi Hunt <qiyong@fc-cn.com> Acked-by: Oleg Nesterov <oleg@tv-sign.ru> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-beck.git / log