Johannes Berg [Thu, 10 Mar 2016 10:55:44 +0000 (11:55 +0100)]
iwlwifi: mvm: pass station to mac80211 RX where known
When we've already looked up the transmitter station, we can just
pass it to mac80211 using the new ieee80211_rx_napi(). This saves
the overhead of looking it up in mac80211 again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Devices belonging to 9000 family can support VHT 160MHz channel
width, so need to consider it when configuring VHT capabilities.
However, NVM file doesn't have a single bit specifying that 160MHz
is supported. This patch turns on 160MHz support in VHT capabilities
in case there's at least one channel supporting 160MHz.
iwlwifi: allow combining different phy images with mac images
Currently there is one to one function between device id to it's ucode.
The new generation devices allows to combine different phy and mac images.
Now we have two different ucode images with the same device id.
Read RF ID to identify phy image and overwrite it if needed.
Luca Coelho [Fri, 11 Mar 2016 10:12:16 +0000 (12:12 +0200)]
iwlwifi: wake from runtime suspend before sending sync commands
If a host command was queued while in runtime suspend, it would go out
before the D0I3_END_CMD was sent. Sometimes it works, but sometimes
it fails, and it is obviously the wrong thing to do.
To fix this, have the opmode take a reference before sending a SYNC
command and make the pcie trans wait for the runtime state to become
active before actually queueing the command.
iwlwifi: mvm: allow a debug knob for Tx A-MSDU even if rate control forbids it
There is a debugfs knob to configure the maximal length
of the A-MSDU. If this value is not 0 (which is the
default), allow Tx A-MSDU even if the rate control
disallows it.
While at it, add "unlikely" to the if that limits the
length of the A-MSDU based on the debugfs hook.
Johannes Berg [Wed, 30 Mar 2016 09:05:16 +0000 (11:05 +0200)]
iwlwifi: mvm: advertise RSS queue usage
In order for mac80211 to use per-CPU statistics for RSS RX, the
driver needs to advertise that it uses RSS. Do this when using
more than a single queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Luca Coelho [Wed, 30 Mar 2016 17:59:27 +0000 (20:59 +0300)]
iwlwifi: trans: don't call the trans-specific ref/unref directly
It's cleaner to always call the iwl_trans_ref/unref() functions
instead of sometimes calling the trans-specific ops directly. This
also prepares for moving some of the code from the trans-specific ops
to the common trans code.
iwlwifi: mvm: support queue removal in ADD_STA hcmd
To indicate to the FW that a queue has been removed, an
existing flag in the ADD_STA HCMD (that hasn't been in use)
has been changed to indicate that a queue is being removed
from a STA.
Sara Sharon [Sun, 28 Feb 2016 13:41:47 +0000 (15:41 +0200)]
iwlwifi: mvm: utilize the frame release infrastructure
The firmware will send frame release notification in order
to release "stuck" frames on a queue where no more frames
arrive on.
Upon receiving the message the driver shall indicate the frames
up to the NSSN.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Sun, 28 Feb 2016 18:28:17 +0000 (20:28 +0200)]
iwlwifi: mvm: add reorder timeout per frame
Add a timer in order to release expired frames from the
reorder buffer.
This is needed since some APs do not retransmit frames
to fill in the reorder holes and in TCP it results with
a complete stall of traffic.
This has a few side effects on the general design:
The nssn may not reflect the the head of the reorder buffer.
This situation is valid, and packets with SN lower than the
reorder buffer head will be dropped.
Another side effect is that since the reorder timer might expire
we need to lock the reorder buffer.
This however is fine since the locking is only inside a
single reorder buffer between RX path and reorder timeout and
there is no outside contention.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Wed, 23 Mar 2016 14:32:02 +0000 (16:32 +0200)]
iwlwifi: mvm: add reorder buffer per queue
Next hardware will direct packets to core based on the TCP/UDP
streams.
This logic can create holes in reorder buffer since packets that
belong to other stream were directed to a different core.
However, those are valid holes and the packets can be indicated
in L3 order.
The hardware will utilize a mechanism of informing the driver of
the normalized ssn and the driver shall release all packets that
SN is lower than the nssn.
This enables managing the reorder across the queues without sharing
any data between them.
The reorder buffer is allocated and released directly in the RX path
in order to avoid various races between control path and rx path.
The code utilizes the internal messaging to notify rx queues of when
to delete the reorder buffer.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Sun, 20 Mar 2016 14:23:41 +0000 (16:23 +0200)]
iwlwifi: mvm: add infrastructure for tracking BA session in driver
According to the spec when a BA session is started there
is a timeout set for the session in the ADDBA request.
If there is not activity on the TA/TID then the session
expires and a DELBA is sent.
In order to check for the timeout, data must be shared
among the rx queues.
Add a timer that runs as long as BA session is active
for the station and stops aggregation session if needed.
This patch also lays the infrastructure for the reordering
buffer which will be enabled in the next patches.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Wed, 23 Mar 2016 14:31:43 +0000 (16:31 +0200)]
iwlwifi: mvm: change RX sync notification to be an attribute and not a type
Currently the sync notification is a type of notification. However, it
is better fitted as an attribute of a notification, since there might
be another message in the payload (delba for instance) that should be
sent while control path is waiting for all queues to process.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
mac80211 will call the driver whenever there is a race between
RSS queues and control path that requires a processing of all
pending frames in RSS queues.
Implement that by utilizing the internal notification mechanism:
queue a message to all queues. When the message is received on
a queue it decrements the atomic counter. This guarantees that
all pending frames in the RX queue were processed since the message
is in order inside the queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Luca Coelho [Tue, 10 May 2016 07:30:56 +0000 (10:30 +0300)]
Merge tag 'mac80211-next-for-davem-2016-04-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next into master
To synchronize with Kalle, here's just a big change that affects
all drivers - removing the duplicated enum ieee80211_band and
replacing it by enum nl80211_band. On top of that, just a small
documentation update.
iwlwifi: mvm: don't override the rate with the AMSDU len
The TSO code creates A-MSDUs from a single large send. Each
A-MSDU is an skb and skb->len doesn't include the number of
bytes which need to be added for the headers being added
(subframe header, TCP header, IP header, SNAP, padding).
To be able to set the right value in the Tx command, we
put the number of bytes added by those headers in
driver_data in iwl_mvm_tx_tso and use this value in
iwl_mvm_set_tx_cmd.
The problem by setting this value in driver_data is that
it overrides the ieee80211_tx_info. The bug manifested
itself when we send P2P related frames in CCK since the
rate in ieee80211_tx_info is zero-ed. This of course is
a violation of the P2P specification.
To fix this, copy the original ieee80211_tx_info to the
stack and pass it to the functions which need it.
Assign the number of bytes added by the headers to the
driver_data inside the skb itself.
Fixes: a6d5e32f247c ("iwlwifi: mvm: send large SKBs to the transport") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Tue, 12 Apr 2016 13:56:15 +0000 (15:56 +0200)]
cfg80211: remove enum ieee80211_band
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The roaming cases for the Connect command were not fully covered and
neither Connect nor Associate command uses of the prev_bssid parameter
were very clear. Add details to describe how the prev_bssid argument is
supposed to be used and when the driver should use association or
reassociation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Matti Gottlieb [Sun, 10 Apr 2016 07:53:57 +0000 (10:53 +0300)]
iwlwifi: mvm: fix accessing Null pointer during fw dump collection
The firwmare file can come with data that is relevant for paging. This
data is availablet to the firmware upon request, but it stored in the
host's memory. During the firmware init flow, the driver configures the
firmware so that the firwmare knows where is the data.
When paging is used, the variable paging_mem_size is the number of bytes
that are available through paging. This variable is not zeror-ed if the
driver fails to configure the paging in the firmware, but the memory is
freed which is inconsistent.
This inconsistency led to a NULL pointer dereference in the code that
collects the debug data.
Fix this by zero-ing the paging_mem_size variable and NULLify the
relevant pointers, so that the code that collects the debug data will
know that the paging data is not available.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sara Sharon [Mon, 11 Apr 2016 12:01:46 +0000 (15:01 +0300)]
iwlwifi: 8000: fix MODULE_FIRMWARE input
The firwmare name for 8000 is iwlwifi-8000C. The C is
appended based on a value read from a register. This
allows to load different firwmare versions based on
the hardware step during development. Now that the
hardware development is completed, we can hard code
the 'C' and along the way, fix the input to
MODULE_FIRMWARE.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=116041
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Ayala Beker [Wed, 3 Feb 2016 13:36:52 +0000 (15:36 +0200)]
iwlwifi: mvm: avoid to WARN about gscan capabilities
Gscan capabilities were updated with new capabilities supported
by the device. Update GSCAN capabilities TLV and avoid to WARN
if the firmware does not have the new capabilities.
David S. Miller [Mon, 11 Apr 2016 15:58:12 +0000 (11:58 -0400)]
Merge tag 'wireless-drivers-next-for-davem-2016-04-11' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.7
Major changes:
iwlwifi
* support for Link Quality measurement
* more work 9000 devices and MSIx
* continuation of the Dynamic Queue Allocation work
* make the paging less memory hungry
* 9000 new Rx path
* removal of IWLWIFI_UAPSD Kconfig option
ath10k
* implement push-pull tx model using mac80211 software queuing support
* enable scan in AP mode (NL80211_FEATURE_AP_SCAN)
wil6210
* add basic PBSS (Personal Basic Service Set) support
* add initial P2P support
* add oob_mode module parameter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
verifier is using the following structure to track the state of registers:
struct reg_state {
enum bpf_reg_type type;
union {
int imm;
struct bpf_map *map_ptr;
};
};
and later on in states_equal() does memcmp(&old->regs[i], &cur->regs[i],..)
to find equivalent states.
Throughout the code of verifier there are assignements to 'imm' and 'map_ptr'
fields and it's not obvious that most of the assignments into 'imm' don't
need to clear extra 4 bytes (like mark_reg_unknown_value() does) to make sure
that memcmp doesn't go over junk left from 'map_ptr' assignment.
Simplify the code by converting 'int' into 'long'
Suggested-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 9 Apr 2016 15:01:13 +0000 (08:01 -0700)]
ipv6: fix inet6_lookup_listener()
A stupid refactoring bug in inet6_lookup_listener() needs to be fixed
in order to get proper SO_REUSEPORT behavior.
Fixes: 3b24d854cb35 ("tcp/dccp: do not touch listener sk_refcnt under synflood") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as
they are 'trivial'"
* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: option: add "D-Link DWM-221 B1" device id
USB: serial: cp210x: Adding GE Healthcare Device ID
USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
usb: dwc3: keystone: drop dma_mask configuration
usb: gadget: udc-core: remove manual dma configuration
usb: dwc3: pci: add ID for one more Intel Broxton platform
usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
usb: dwc2: do not override forced dr_mode in gadget setup
usb: gadget: f_midi: unlock on error
USB: digi_acceleport: do sanity checking for the number of ports
USB: cypress_m8: add endpoint sanity check
USB: mct_u232: add sanity checking in probe
usb: fix regression in SuperSpeed endpoint descriptor parsing
USB: usbip: fix potential out-of-bounds write
usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
usb: phy: qcom-8x16: fix regulator API abuse
usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
usb: gadget: composite: Access SSP Dev Cap fields properly
...
Merge tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some IIO driver fixes, along with two staging driver fixes
for 4.6-rc3.
One staging driver patch reverts the deletion of a driver that
happened in 4.6-rc1. We thought that laptop.org was dead, but it's
still alive and kicking, and has users that were mad we broke their
hardware by deleting a driver for their machines. So that driver is
added back and everyone is happy again.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: olpc_dcon: Remove obsolete driver"
staging/rdma/hfi1: select CRC32
iio: gyro: bmg160: fix buffer read values
iio: gyro: bmg160: fix endianness when reading axes
iio: accel: bmc150: fix endianness when reading axes
iio: st_magn: always define ST_MAGN_TRIGGER_SET_STATE
iio: fix config watermark initial value
iio: health: max30100: correct FIFO check condition
iio: imu: Fix inv_mpu6050 dependencies
iio: adc: Fix build error of missing devm_ioremap_resource on UM
iio: light: apds9960: correct FIFO check condition
iio: adc: max1363: correct reference voltage
iio: adc: max1363: add missing adc to max1363_id
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of eight fixes.
Two are trivial gcc-6 updates (brace additions and unused variable
removal). There's a couple of cxlflash regressions, a correction for
sd being overly chatty on revalidation (causing excess log increases).
A VPD issue which could crash USB devices because they seem very
intolerant to VPD inquiries, an ALUA deadlock fix and a mpt3sas buffer
overrun fix"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Do not attach VPD to devices that don't support it
sd: Fix excessive capacity printing on devices with blocks bigger than 512 bytes
scsi_dh_alua: Fix a recently introduced deadlock
scsi: Declare local symbols static
cxlflash: Move to exponential back-off when cmd_room is not available
cxlflash: Fix regression issue with re-ordering patch
mpt3sas: Don't overreach ioc->reply_post[] during initialization
aacraid: add missing curly braces
- fix error handling (Guoqing)
- fix a crash when a disk is hotremoved (me)
- fix a dead loop (Wei Fang)"
* tag 'md/4.6-rc2-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/bitmap: clear bitmap if bitmap_create failed
MD: add rdev reference for super write
md: fix a trivial typo in comments
md:raid1: fix a dead loop when read from a WriteMostly disk
Merge tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Fixes for some issues discovered after recent changes and for some
that have just been found lately regardless of those changes
(intel_pstate, intel_idle, PM core, mailbox/pcc, turbostat) plus
support for some new CPU models (intel_idle, Intel RAPL driver,
turbostat) and documentation updates (intel_pstate, PM core).
Specifics:
- intel_pstate fixes for two issues exposed by the recent switch over
from using timers and for one issue introduced during the 4.4 cycle
plus new comments describing data structures used by the driver
(Rafael Wysocki, Srinivas Pandruvada).
- intel_idle fixes related to CPU offline/online (Richard Cochran).
- intel_idle support (new CPU IDs and state definitions mostly) for
Skylake-X and Kabylake processors (Len Brown).
- PCC mailbox driver fix for an out-of-bounds memory access that may
cause the kernel to panic() (Shanker Donthineni).
- New (missing) CPU ID for one apparently overlooked Haswell model in
the Intel RAPL power capping driver (Srinivas Pandruvada).
- Fix for the PM core's wakeup IRQs framework to make it work after
wakeup settings reconfiguration from sysfs (Grygorii Strashko).
- Runtime PM documentation update to make it describe what needs to
be done during device removal more precisely (Krzysztof Kozlowski).
- Stale comment removal cleanup in the cpufreq-dt driver (Viresh
Kumar).
- turbostat utility fixes and support for Broxton, Skylake-X and
Kabylake processors (Len Brown)"
* tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
intel_idle: Add KBL support
intel_idle: Add SKX support
intel_idle: Clean up all registered devices on exit.
intel_idle: Propagate hot plug errors.
intel_idle: Don't overreact to a cpuidle registration failure.
intel_idle: Setup the timer broadcast only on successful driver load.
intel_idle: Avoid a double free of the per-CPU data.
intel_idle: Fix dangling registration on error path.
intel_idle: Fix deallocation order on the driver exit path.
intel_idle: Remove redundant initialization calls.
intel_idle: Fix a helper function's return value.
intel_idle: remove useless return from void function.
...
1) Stale SKB data pointer access across pskb_may_pull() calls in L2TP,
from Haishuang Yan.
2) Fix multicast frame handling in mac80211 AP code, from Felix
Fietkau.
3) mac80211 station hashtable insert errors not handled properly, fix
from Johannes Berg.
4) Fix TX descriptor count limit handling in e1000, from Alexander
Duyck.
5) Revert a buggy netdev refcount fix in netpoll, from Bjorn Helgaas.
6) Must assign rtnl_link_ops of the device before registering it, fix
in ip6_tunnel from Thadeu Lima de Souza Cascardo.
7) Memory leak fix in tc action net exit, from WANG Cong.
8) Add missing AF_KCM entries to name tables, from Dexuan Cui.
9) Fix regression in GRE handling of csums wrt. FOU, from Alexander
Duyck.
10) Fix memory allocation alignment and congestion map corruption in
RDS, from Shamir Rabinovitch.
11) Fix default qdisc regression in tuntap driver, from Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge, netem: mark mailing lists as moderated
tuntap: restore default qdisc
mpls: find_outdev: check for err ptr in addition to NULL check
ipv6: Count in extension headers in skb->network_header
RDS: fix congestion map corruption for PAGE_SIZE > 4k
RDS: memory allocated must be align to 8
GRE: Disable segmentation offloads w/ CSUM and we are encapsulated via FOU
net: add the AF_KCM entries to family name tables
MAINTAINERS: intel-wired-lan list is moderated
lib/test_bpf: Add additional BPF_ADD tests
lib/test_bpf: Add test to check for result of 32-bit add that overflows
lib/test_bpf: Add tests for unsigned BPF_JGT
lib/test_bpf: Fix JMP_JSET tests
VSOCK: Detach QP check should filter out non matching QPs.
stmmac: fix adjust link call in case of a switch is attached
af_packet: tone down the Tx-ring unsupported spew.
net_sched: fix a memory leak in tc action
samples/bpf: Enable powerpc support
samples/bpf: Use llc in PATH, rather than a hardcoded value
samples/bpf: Fix build breakage with map_perf_test_user.c
...
Merge branch 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"These are bug fixes, including a really old fsync bug, and a few trace
points to help us track down problems in the quota code"
* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix file/data loss caused by fsync after rename and new inode
btrfs: Reset IO error counters before start of device replacing
btrfs: Add qgroup tracing
Btrfs: don't use src fd for printk
btrfs: fallback to vmalloc in btrfs_compare_tree
btrfs: handle non-fatal errors in btrfs_qgroup_inherit()
btrfs: Output more info for enospc_debug mount option
Btrfs: fix invalid reference in replace_path
Btrfs: Improve FL_KEEP_SIZE handling in fallocate
Merge tag 'for-linus-4.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull orangefs fixes from Mike Marshall:
"Orangefs cleanups and a strncpy vulnerability fix.
Cleanups:
- remove an unused variable from orangefs_readdir.
- clean up printk wrapper used for ofs "gossip" debugging.
- clean up truncate ctime and mtime setting in inode.c
- remove a useless null check found by coccinelle.
- optimize some memcpy/memset boilerplate code.
- remove some useless sanity checks from xattr.c
Fix:
- fix a potential strncpy vulnerability"
* tag 'for-linus-4.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: remove unused variable
orangefs: Add KERN_<LEVEL> to gossip_<level> macros
orangefs: strncpy -> strscpy
orangefs: clean up truncate ctime and mtime setting
Orangefs: fix ifnullfree.cocci warnings
Orangefs: optimize boilerplate code.
Orangefs: xattr.c cleanup
Merge tag 'iommu-fixes-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- compile-time fixes (warnings and failures)
- a bug in iommu core code which could cause the group->domain pointer
to be falsly cleared
- fix in scatterlist handling of the ARM common DMA-API code
- stall detection fix for the Rockchip IOMMU driver
* tag 'iommu-fixes-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Silence an uninitialized variable warning
iommu/rockchip: Fix "is stall active" check
iommu: Don't overwrite domain pointer when there is no default_domain
iommu/dma: Restore scatterlist offsets correctly
iommu: provide of_xlate pointer unconditionally
John Allen [Wed, 6 Apr 2016 16:49:55 +0000 (11:49 -0500)]
ibmvnic: Enable use of multiple tx/rx scrqs
Enables the use of multiple transmit and receive scrqs allowing the ibmvnic
driver to take advantage of multiqueue functionality. To achieve this, the
driver must implement the process of negotiating the maximum number of
queues allowed by the server. Initially, the driver will attempt to login
with the maximum number of tx and rx queues supported by the server. If
the server fails to allocate the requested number of scrqs, it will return
partial success in the login response. In this case, we must reinitiate
the login process from the request capabilities stage and attempt to login
requesting fewer scrqs.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 8 Apr 2016 20:50:41 +0000 (16:50 -0400)]
Merge branch 'dsa-voidify-ops'
Vivien Didelot says:
====================
net: dsa: voidify STP setter and FDB/VLAN add ops
Neither the DSA layer nor the bridge code (see br_set_state) really care
about eventual errors from STP state setters, so make it void.
The DSA layer separates the prepare and commit phases of switchdev in
two different functions. Logical errors must not happen in commit
routines, so make them void.
Changes v1 -> v2:
- rename port_stp_update to port_stp_state_set
- don't change code flow of bcm_sf2_sw_br_set_stp_state
- prefer netdev_err over netdev_warn
====================
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 6 Apr 2016 15:55:05 +0000 (11:55 -0400)]
net: dsa: make the VLAN add function return void
The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.
The DSA layer separates port_vlan_prepare and port_vlan_add for
simplicity and convenience. If an hardware error occurs during the
commit phase, there is no need to report it outside the driver itself.
Make the DSA port_vlan_add routine return void for explicitness.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 6 Apr 2016 15:55:04 +0000 (11:55 -0400)]
net: dsa: make the FDB add function return void
The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.
The DSA layer separates port_fdb_prepare and port_fdb_add for simplicity
and convenience. If an hardware error occurs during the commit phase,
there is no need to report it outside the DSA driver itself.
Make the DSA port_fdb_add routine return void for explicitness.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 6 Apr 2016 15:55:03 +0000 (11:55 -0400)]
net: dsa: make the STP state function return void
The DSA layer doesn't care about the return code of the port_stp_update
routine, so make it void in the layer and the DSA drivers.
Replace the useless dsa_slave_stp_update function with a
dsa_slave_stp_state function used to reply to the switchdev
SWITCHDEV_ATTR_ID_PORT_STP_STATE attribute.
In the meantime, rename port_stp_update to port_stp_state_set to
explicit the state change.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 6 Apr 2016 15:06:20 +0000 (11:06 -0400)]
net: dsa: document missing functions
Add description for the missing port_vlan_prepare, port_fdb_prepare,
port_fdb_dump functions in the DSA documentation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 8 Apr 2016 20:42:31 +0000 (16:42 -0400)]
Merge tag 'mac80211-next-for-davem-2016-04-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the 4.7 cycle, we have a number of changes:
* Bob's mesh mode rhashtable conversion, this includes
the rhashtable API change for allocation flags
* BSSID scan, connect() command reassoc support (Jouni)
* fast (optimised data only) and support for RSS in mac80211 (myself)
* various smaller changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 8 Apr 2016 20:41:28 +0000 (16:41 -0400)]
Merge tag 'mac80211-for-davem-2016-04-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
For the current RC series, we have the following fixes:
* TDLS fixes from Arik and Ilan
* rhashtable fixes from Ben and myself
* documentation fixes from Luis
* U-APSD fixes from Emmanuel
* a TXQ fix from Felix
* and a compiler warning suppression from Jeff
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 5 Apr 2016 20:33:17 +0000 (22:33 +0200)]
bpf, verifier: further improve search pruning
The verifier needs to go through every path of the program in
order to check that it terminates safely, which can be quite a
lot of instructions that need to be processed f.e. in cases with
more branchy programs. With search pruning from f1bca824dabb ("bpf:
add search pruning optimization to verifier") the search space can
already be reduced significantly when the verifier detects that
a previously walked path with same register and stack contents
terminated already (see verifier's states_equal()), so the search
can skip walking those states.
When working with larger programs of > ~2000 (out of max 4096)
insns, we found that the current limit of 32k instructions is easily
hit. For example, a case we ran into is that the search space cannot
be pruned due to branches at the beginning of the program that make
use of certain stack space slots (STACK_MISC), which are never used
in the remaining program (STACK_INVALID). Therefore, the verifier
needs to walk paths for the slots in STACK_INVALID state, but also
all remaining paths with a stack structure, where the slots are in
STACK_MISC, which can nearly double the search space needed. After
various experiments, we find that a limit of 64k processed insns is
a more reasonable choice when dealing with larger programs in practice.
This still allows to reject extreme crafted cases that can have a
much higher complexity (f.e. > ~300k) within the 4096 insns limit
due to search pruning not being able to take effect.
Furthermore, we found that a lot of states can be pruned after a
call instruction, f.e. we were able to reduce the search state by
~35% in some cases with this heuristic, trade-off is to keep a bit
more states in env->explored_states. Usually, call instructions
have a number of preceding register assignments and/or stack stores,
where search pruning has a better chance to suceed in states_equal()
test. The current code marks the branch targets with STATE_LIST_MARK
in case of conditional jumps, and the next (t + 1) instruction in
case of unconditional jump so that f.e. a backjump will walk it. We
also did experiments with using t + insns[t].off + 1 as a marker in
the unconditionally jump case instead of t + 1 with the rationale
that these two branches of execution that converge after the label
might have more potential of pruning. We found that it was a bit
better, but not necessarily significantly better than the current
state, perhaps also due to clang not generating back jumps often.
Hence, we left that as is for now.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Fri, 8 Apr 2016 05:26:48 +0000 (13:26 +0800)]
tuntap: restore default qdisc
After commit f84bb1eac027 ("net: fix IFF_NO_QUEUE for drivers using
alloc_netdev"), default qdisc was changed to noqueue because
tuntap does not set tx_queue_len during .setup(). This patch restores
default qdisc by setting tx_queue_len in tun_setup().
Fixes: f84bb1eac027 ("net: fix IFF_NO_QUEUE for drivers using alloc_netdev") Cc: Phil Sutter <phil@nwl.cc> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branches 'pm-core', 'powercap' and 'pm-tools'
* pm-core:
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
PM / runtime: Document steps for device removal
* powercap:
powercap: intel_rapl: Add missing Haswell model
* pm-tools:
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
Merge branches 'pm-cpufreq', 'pm-cpuidle' and 'acpi-cppc'
* pm-cpufreq:
cpufreq: dt: Drop stale comment
cpufreq: intel_pstate: Documenation for structures
cpufreq: intel_pstate: fix inconsistency in setting policy limits
intel_pstate: Avoid extra invocation of intel_pstate_sample()
intel_pstate: Do not set utilization update hook too early
* pm-cpuidle:
intel_idle: Add KBL support
intel_idle: Add SKX support
intel_idle: Clean up all registered devices on exit.
intel_idle: Propagate hot plug errors.
intel_idle: Don't overreact to a cpuidle registration failure.
intel_idle: Setup the timer broadcast only on successful driver load.
intel_idle: Avoid a double free of the per-CPU data.
intel_idle: Fix dangling registration on error path.
intel_idle: Fix deallocation order on the driver exit path.
intel_idle: Remove redundant initialization calls.
intel_idle: Fix a helper function's return value.
intel_idle: remove useless return from void function.
* acpi-cppc:
mailbox: pcc: Don't access an unmapped memory address space
devlink: share user_ptr pointer for both devlink and devlink_port
Ptr to devlink structure can be easily obtained from
devlink_port->devlink. So share user_ptr[0] pointer for both and leave
user_ptr[1] free for other users.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: Move devlink port registration into common core code
Remove devlink port reg/unreg from spectrum and switchx2 code and rather
do the common work in core. That also ensures code separation where
devlink is only used in core.c.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
devlink: remove implicit type set in port register
As we rely on caller zeroing or correctly set the struct before the call,
this implicit type set is either no-op (DEVLINK_PORT_TYPE_NOTSET is 0)
or it rewrites wanted value. So remove this.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 8 Apr 2016 19:26:07 +0000 (15:26 -0400)]
Merge branch 'nfp-mtu-buffer-reconfig'
Jakub Kicinski says:
====================
MTU/buffer reconfig changes
I re-discussed MPLS/MTU internally, dropped it from the patch 1,
re-tested everything, found out I forgot about debugfs pointers,
fixed that as well.
v5:
- don't reserve space in RX buffers for MPLS label stack
(patch 1);
- fix debugfs pointers to ring structures (patch 5).
v4:
- cut down on unrelated patches;
- don't "close" the device on error path.
--- v4 cover letter
Previous series included some not entirely related patches,
this one is cut down. Main issue I'm trying to solve here
is that .ndo_change_mtu() in nfpvf driver is doing full
close/open to reallocate buffers - which if open fails
can result in device being basically closed even though
the interface is started. As suggested by you I try to move
towards a paradigm where the resources are allocated first
and the MTU change is only done once I'm certain (almost)
nothing can fail. Almost because I need to communicate
with FW and that can always time out.
Patch 1 fixes small issue. Next 10 patches reorganize things
so that I can easily allocate new rings and sets of buffers
while the device is running. Patches 13 and 15 reshape the
.ndo_change_mtu() and ethtool's ring-resize operation into
desired form.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 7 Apr 2016 18:39:46 +0000 (19:39 +0100)]
nfp: convert .ndo_change_mtu() to prepare/commit paradigm
When changing MTU on running device first allocate new rings
and buffers and once it succeeds proceed with changing MTU.
Allocation of new rings is not really necessary for this
operation - it's done to keep the code simple and because
size of the extra ring memory is quite small compared to
the size of buffers.
Operation can still fail midway through if FW communication
times out. In that case we retry with old MTU (rings).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 7 Apr 2016 18:39:45 +0000 (19:39 +0100)]
nfp: propagate list buffer size in struct rx_ring
Free list buffer size needs to be propagated to few functions
as a parameter and added to struct nfp_net_rx_ring since soon
some of the functions will be reused to manage rings with
buffers of size different than nn->fl_bufsz.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 7 Apr 2016 18:39:44 +0000 (19:39 +0100)]
nfp: sync ring state during FW reconfiguration
FW reconfiguration in .ndo_open()/.ndo_stop() should reset/
restore queue state. Since we need IRQs to be disabled when
filling rings on RX path we have to move disable_irq() from
.ndo_open() all the way up to IRQ allocation.
nfp_net_start_vec() becomes trivial now so it's inlined.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 7 Apr 2016 18:39:42 +0000 (19:39 +0100)]
nfp: move filling ring information to FW config
nfp_net_[rt]x_ring_{alloc,free} should only allocate or free
ring resources without touching the device. Move setting
parameters in the BAR to separate functions. This will make
it possible to reuse alloc/free functions to allocate new
rings while the device is running.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 7 Apr 2016 18:39:41 +0000 (19:39 +0100)]
nfp: preallocate RX buffers early in .ndo_open
We want the .ndo_open() to have following structure:
- allocate resources;
- configure HW/FW;
- enable the device from stack perspective.
Therefore filling RX rings needs to be moved to the beginning
of .ndo_open().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 7 Apr 2016 18:39:40 +0000 (19:39 +0100)]
nfp: reorganize initial filling of RX rings
Separate allocation of buffers from giving them to FW,
thanks to this it will be possible to move allocation
earlier on .ndo_open() path and reuse buffers during
runtime reconfiguration.
Similar to TX side clean up the spill of functionality
from flush to freeing the ring. Unlike on TX side,
RX ring reset does not free buffers from the ring.
Ring reset means only that FW pointers are zeroed and
buffers on the ring must be placed in [0, cnt - 1)
positions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 7 Apr 2016 18:39:39 +0000 (19:39 +0100)]
nfp: cleanup tx ring flush and rename to reset
Since we never used flush without freeing the ring later
the functionality of the two operations is mixed.
Rename flush to ring reset and move there all the things
which have to be done after FW ring state is cleared.
While at it do some clean-ups.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 7 Apr 2016 18:39:37 +0000 (19:39 +0100)]
nfp: make *x_ring_init do all the init
nfp_net_[rt]x_ring_init functions used to be called from probe
path only and some of their functionality was spilled to the
call site. In order to reuse them for ring reconfiguration
we need them to do all the init.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 7 Apr 2016 18:39:36 +0000 (19:39 +0100)]
nfp: break up nfp_net_{alloc|free}_rings
nfp_net_{alloc|free}_rings contained strange mix of allocations
and vector initialization. Remove it, declare vector init as
a separate function and handle allocations explicitly.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 7 Apr 2016 18:39:35 +0000 (19:39 +0100)]
nfp: move link state interrupt request/free calls
We need to be able to disable the link state interrupt when
the device is brought down. We used to just free the IRQ
at the beginning of .ndo_stop(). As we now move towards
more ordered .ndo_open()/.ndo_stop() paths LSC allocation
should be placed in the "allocate resource" section.
Since the IRQ can't be freed early in .ndo_stop(), it is
disabled instead.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 7 Apr 2016 18:39:34 +0000 (19:39 +0100)]
nfp: correct RX buffer length calculation
When calculating the RX buffer length we need to account
for up to 2 VLAN tags. Rounding up to 1k is an relic of
a distant past and can be removed. While at it also remove
trivial print statement.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It would have been possible for a rogue client-core to send in a symlink
target which is not NUL terminated. This returns EIO if the client-core
gives us corrupt data.
Leave debugfs and superblock code as is for now.
Other dcache.c and namei.c strncpy instances are safe because
ORANGEFS_NAME_MAX = NAME_MAX + 1; there is always enough space for a
name plus a NUL byte.
Signed-off-by: Martin Brandenburg <martin@omnibond.com> Signed-off-by: Mike Marshall <hubcap@omnibond.com>
fs/orangefs/orangefs-debugfs.c:130:2-26: WARNING: NULL check before freeing functions like kfree, debugfs_remove, debugfs_remove_recursive or usb_free_urb is not needed. Maybe consider reorganizing relevant code to avoid passing NULL values.
NULL check before some freeing functions is not needed.
Based on checkpatch warning
"kfree(NULL) is safe this check is probably not required"
and kfreeaddr.cocci by Julia Lawall.
mpls: find_outdev: check for err ptr in addition to NULL check
find_outdev calls inet{,6}_fib_lookup_dev() or dev_get_by_index() to
find the output device. In case of an error, inet{,6}_fib_lookup_dev()
returns error pointer and dev_get_by_index() returns NULL. But the function
only checks for NULL and thus can end up calling dev_put on an ERR_PTR.
This patch adds an additional check for err ptr after the NULL check.
After patch:
$ip -f mpls route add 100 as 200 via inet 10.1.1.8
RTNETLINK answers: Network is unreachable
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reported-by: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 8 Apr 2016 16:13:30 +0000 (12:13 -0400)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-04-07
This series contains updates to ixgbe and ixgbevf.
This entire series (except for one patch from Alex) comes from Mark and
is mainly to add support for our new MAC (x550em_a).
So let's get Alex's patch out of the way first before we cover Mark's
many changes. Alex does his enable bulk free in transmit cleanup for
ixgbe and ixgbevf, like his has done for all of our other drivers.
First Mark cleans up registers that were not being used, so do some
house cleaning. Then to avoid casting lan_id and func fields, just
make them u8 since they only hold small values anyways. Found and
fixed an issue where on read operations it could be possible to
modify locations beyond the length passed in, so change the check
to round up in the same way. Cleaned up the interface for issuing
firmware commands to use a void * instead of a u32 * which eliminates
a number of casts. Added support for the new MAC and provided method
pointers and use them to access IOSF-attached devices, since the
new MAC will also need a new access method. Added support for SFPs
with an external retimer and for an SGMII backplane interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Sitnicki [Tue, 5 Apr 2016 16:41:08 +0000 (18:41 +0200)]
ipv6: Count in extension headers in skb->network_header
When sending a UDPv6 message longer than MTU, account for the length
of fragmentable IPv6 extension headers in skb->network_header offset.
Same as we do in alloc_new_skb path in __ip6_append_data().
This ensures that later on __ip6_make_skb() will make space in
headroom for fragmentable extension headers:
/* move skb->data to ip header from ext header */
if (skb->data < skb_network_header(skb))
__skb_pull(skb, skb_network_offset(skb));
Reported-by: Ji Jianwen <jiji@redhat.com> Signed-off-by: Jakub Sitnicki <jkbs@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Aside from the crash, the shortcomings of that patch are as follows:
- It makes the ib_srpt driver use I/O contexts allocated by
transport_alloc_session_tags() but it does not initialize these I/O
contexts properly. All the initializations performed by
srpt_alloc_ioctx() are skipped.
- It swaps the order of the send ioctx allocation and the transition to
RTR mode which is wrong.
- The amount of memory that is needed for I/O contexts is doubled.
- srpt_rdma_ch.free_list is no longer used but is not removed.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Fri, 8 Apr 2016 01:04:27 +0000 (21:04 -0400)]
Merge branch 'bpf-tracepoints'
Alexei Starovoitov says:
====================
allow bpf attach to tracepoints
Hi Steven, Peter,
v1->v2: addressed Peter's comments:
- fixed wording in patch 1, added ack
- refactored 2nd patch into 3:
2/10 remove unused __perf_addr macro which frees up
an argument in perf_trace_buf_submit
3/10 split perf_trace_buf_prepare into alloc and update parts, so that bpf
programs don't have to pay performance penalty for update of struct trace_entry
which is not going to be accessed by bpf
4/10 actual addition of bpf filter to perf tracepoint handler is now trivial
and bpf prog can be used as proper filter of tracepoints
v1 cover:
last time we discussed bpf+tracepoints it was a year ago [1] and the reason
we didn't proceed with that approach was that bpf would make arguments
arg1, arg2 to trace_xx(arg1, arg2) call to be exposed to bpf program
and that was considered unnecessary extension of abi. Back then I wanted
to avoid the cost of buffer alloc and field assign part in all
of the tracepoints, but looks like when optimized the cost is acceptable.
So this new apporach doesn't expose any new abi to bpf program.
The program is looking at tracepoint fields after they were copied
by perf_trace_xx() and described in /sys/kernel/debug/tracing/events/xxx/format
We made a tool [2] that takes arguments from /sys/.../format and works as:
$ tplist.py -v random:urandom_read
int got_bits;
int pool_left;
int input_left;
Then these fields can be copy-pasted into bpf program like:
struct urandom_read {
__u64 hidden_pad;
int got_bits;
int pool_left;
int input_left;
};
and the program can use it:
SEC("tracepoint/random/urandom_read")
int bpf_prog(struct urandom_read *ctx)
{
return ctx->pool_left > 0 ? 1 : 0;
}
This way the program can access tracepoint fields faster than
equivalent bpf+kprobe program, which is the main goal of these patches.
Patch 1-4 are simple changes in perf core side, please review.
I'd like to take the whole set via net-next tree, since the rest of
the patches might conflict with other bpf work going on in net-next
and we want to avoid cross-tree merge conflicts.
Alternatively we can put patches 1-4 into both tip and net-next.
Patch 9 is an example of access to tracepoint fields from bpf prog.
Patch 10 is a micro benchmark for bpf+kprobe vs bpf+tracepoint.
Note that for actual tracing tools the user doesn't need to
run tplist.py and copy-paste fields manually. The tools do it
automatically. Like argdist tool [3] can be used as:
$ argdist -H 't:block:block_rq_complete():u32:nr_sector'
where 'nr_sector' is name of tracepoint field taken from
/sys/kernel/debug/tracing/events/block/block_rq_complete/format
and appropriate bpf program is generated on the fly.
samples/bpf: add tracepoint vs kprobe performance tests
the first microbenchmark does
fd=open("/proc/self/comm");
for() {
write(fd, "test");
}
and on 4 cpus in parallel:
writes per sec
base (no tracepoints, no kprobes) 930k
with kprobe at __set_task_comm() 420k
with tracepoint at task:task_rename 730k
For kprobe + full bpf program manully fetches oldcomm, newcomm via bpf_probe_read.
For tracepint bpf program does nothing, since arguments are copied by tracepoint.
2nd microbenchmark does:
fd=open("/dev/urandom");
for() {
read(fd, buf);
}
and on 4 cpus in parallel:
reads per sec
base (no tracepoints, no kprobes) 300k
with kprobe at urandom_read() 279k
with tracepoint at random:urandom_read 290k
bpf progs attached to kprobe and tracepoint are noop.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
during bpf program loading remember the last byte of ctx access
and at the time of attaching the program to tracepoint check that
the program doesn't access bytes beyond defined in tracepoint fields
This also disallows access to __dynamic_array fields, but can be
relaxed in the future.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
perf, bpf: allow bpf programs attach to tracepoints
introduce BPF_PROG_TYPE_TRACEPOINT program type and allow it to be attached
to the perf tracepoint handler, which will copy the arguments into
the per-cpu buffer and pass it to the bpf program as its first argument.
The layout of the fields can be discovered by doing
'cat /sys/kernel/debug/tracing/events/sched/sched_switch/format'
prior to the compilation of the program with exception that first 8 bytes
are reserved and not accessible to the program. This area is used to store
the pointer to 'struct pt_regs' which some of the bpf helpers will use:
+---------+
| 8 bytes | hidden 'struct pt_regs *' (inaccessible to bpf program)
+---------+
| N bytes | static tracepoint fields defined in tracepoint/format (bpf readonly)
+---------+
| dynamic | __dynamic_array bytes of tracepoint (inaccessible to bpf yet)
+---------+
Not that all of the fields are already dumped to user space via perf ring buffer
and broken application access it directly without consulting tracepoint/format.
Same rule applies here: static tracepoint fields should only be accessed
in a format defined in tracepoint/format. The order of fields and
field sizes are not an ABI.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log