Joao Pinto [Fri, 31 Mar 2017 13:22:02 +0000 (14:22 +0100)]
net: stmmac: fix cbs configuration
Sending again, because forgot to include net-dev.
The QoS IP does not accept AVB capabilities to default/queue 0, this way we
guarantee 75% bandwidth for AVB. This patch assures that only queues >= 1
gets CBS confgured. Additional info was also added to stmmac.txt.
Reported-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: Joao Pinto <jpinto@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 2 Apr 2017 03:21:45 +0000 (20:21 -0700)]
Merge branch 'mpls-more-labels'
David Ahern says:
====================
net: mpls: Allow users to configure more labels per route
Increase the maximum number of new labels for MPLS routes from 2 to 30.
To keep memory consumption in check, the labels array is moved to the end
of mpls_nh and mpls_iptunnel_encap structs as a 0-sized array. Allocations
use the maximum number of labels across all nexthops in a route for LSR
and the number of labels configured for LWT.
The mpls_route layout is changed to:
+----------------------+
| mpls_route |
+----------------------+
| mpls_nh 0 |
+----------------------+
| alignment padding | 4 bytes for odd number of labels; 0 for even
+----------------------+
| via[rt_max_alen] 0 |
+----------------------+
| alignment padding | via's aligned on sizeof(unsigned long)
+----------------------+
| ... |
Meaning the via follows its mpls_nh providing better locality as the
number of labels increases. UDP_RR tests with namespaces shows no impact
to a modest performance increase with this layout for 1 or 2 labels and
1 or 2 nexthops.
mpls_route allocation size is limited to 4096 bytes allowing on the
order of 30 nexthops with 30 labels (or more nexthops with fewer
labels). LWT encap shares same maximum number of labels as mpls routing.
v3
- initialize n_labels to 0 in case RTA_NEWDST is not defined; detected
by the kbuild test robot
v2
- updates per Eric's comments
+ added patch to ensure all reads of rt_nhn_alive and nh_flags in
the packet path use READ_ONCE and all writes via event handlers
use WRITE_ONCE
+ limit mpls_route size to 4096 (PAGE_SIZE for most arch)
+ mostly killed use of MAX_NEW_LABELS; it exists only for common
limit between lwt and routing paths
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 31 Mar 2017 14:14:04 +0000 (07:14 -0700)]
net: mpls: Increase max number of labels for lwt encap
Alow users to push down more labels per MPLS encap. Similar to LSR case,
move label array to the end of mpls_iptunnel_encap and allocate based on
the number of labels for the route.
For consistency with the LSR case, re-use the same maximum number of
labels.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 31 Mar 2017 14:14:03 +0000 (07:14 -0700)]
net: mpls: bump maximum number of labels
Allow users to push down more labels per MPLS route. With the previous
patches, no memory allocations are based on MAX_NEW_LABELS; the limit
is only used to keep userspace in check.
At this point MAX_NEW_LABELS is only used for mpls_route_config (copying
route data from userspace) and processing nexthops looking for the max
number of labels across the route spec.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 31 Mar 2017 14:14:01 +0000 (07:14 -0700)]
net: mpls: change mpls_route layout
Move labels to the end of mpls_nh as a 0-sized array and within mpls_route
move the via for a nexthop after the mpls_nh. The new layout becomes:
+----------------------+
| mpls_route |
+----------------------+
| mpls_nh 0 |
+----------------------+
| alignment padding | 4 bytes for odd number of labels; 0 for even
+----------------------+
| via[rt_max_alen] 0 |
+----------------------+
| alignment padding | via's aligned on sizeof(unsigned long)
+----------------------+
| ... |
+----------------------+
| mpls_nh n-1 |
+----------------------+
| via[rt_max_alen] n-1 |
+----------------------+
Memory allocated for nexthop + via is constant across all nexthops and
their via. It is based on the maximum number of labels across all nexthops
and the maximum via length. The size is saved in the mpls_route as
rt_nh_size. Accessing a nexthop becomes rt->rt_nh + index * rt->rt_nh_size.
The offset of the via address from a nexthop is saved as rt_via_offset
so that given an mpls_nh pointer the via for that hop is simply
nh + rt->rt_via_offset.
With prior code, memory allocated per mpls_route with 1 nexthop:
via is an ethernet address - 64 bytes
via is an ipv4 address - 64
via is an ipv6 address - 72
With this patch set, memory allocated per mpls_route with 1 nexthop and
1 or 2 labels:
via is an ethernet address - 56 bytes
via is an ipv4 address - 56
via is an ipv6 address - 64
The 8-byte reduction is due to the previous patch; the change introduced
by this patch has no impact on the size of allocations for 1 or 2 labels.
Performance impact of this change was examined using network namespaces
with veth pairs connecting namespaces. ns0 inserts the packet to the
label-switched path using an lwt route with encap mpls. ns1 adds 1 or 2
labels depending on test, ns2 (and ns3 for 2-label test) pops the label
and forwards. ns3 (or ns4) for a 2-label is the destination. Similar
series of namespaces used for 2-nexthop test.
Intent is to measure changes to latency (overhead in manipulating the
packet) in the forwarding path. Tests used netperf with UDP_RR.
In short, the change has no effect to a modest increase in performance.
This is expected since this patch does not really have an impact on routes
with 1 or 2 labels (the current limit) and 1 or 2 nexthops.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 31 Mar 2017 14:14:00 +0000 (07:14 -0700)]
net: mpls: Convert number of nexthops to u8
Number of nexthops and number of alive nexthops are tracked using an
unsigned int. A route should never have more than 255 nexthops so
convert both to u8. Update all references and intermediate variables
to consistently use u8 as well.
Shrinks the size of mpls_route from 32 bytes to 24 bytes with a 2-byte
hole before the nexthops.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 31 Mar 2017 14:13:59 +0000 (07:13 -0700)]
net: mpls: rt_nhn_alive and nh_flags should be accessed using READ_ONCE
The number of alive nexthops for a route (rt->rt_nhn_alive) and the
flags for a next hop (nh->nh_flags) are modified by netdev event
handlers. The event handlers run with rtnl_lock held so updates are
always done with the lock held. The packet path accesses the fields
under the rcu lock. Since those fields can change at any moment in
the packet path, both fields should be accessed using READ_ONCE. Updates
to both fields should use WRITE_ONCE.
Update mpls_select_multipath (packet path) and mpls_ifdown and mpls_ifup
(event handlers) accordingly.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 31 Mar 2017 09:47:39 +0000 (11:47 +0200)]
udp: use sk_protocol instead of pcflag to detect udplite sockets
In the udp_sock struct, the 'forward_deficit' and 'pcflag' fields
share the same cacheline. While the first is dirtied by
udp_recvmsg, the latter is read, possibly several times, by the
bottom half processing to discriminate between udp and udplite
sockets.
With this patch, sk->sk_protocol is used to check is the socket is
really an udplite one, avoiding some cache misses per
packet and improving the performance under udp_flood with
small packet up to 10%.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Regnery [Fri, 31 Mar 2017 09:44:52 +0000 (11:44 +0200)]
net: dsa: fix build error with devlink build as module
After commit 96567d5dacf4 ("net: dsa: dsa2: Add basic support of devlink")
I see the following link error with CONFIG_NET_DSA=y and CONFIG_NET_DEVLINK=m:
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe226b): undefined reference to `devlink_alloc'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe2284): undefined reference to `devlink_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe243e): undefined reference to `devlink_port_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe24e1): undefined reference to `devlink_port_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe24fa): undefined reference to `devlink_port_type_eth_set'
net/built-in.o: In function 'dsa_dst_unapply.part.8':
dsa2.c:(.text.unlikely+0x345): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x36c): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x38e): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x3f2): undefined reference to 'devlink_unregister'
dsa2.c:(.text.unlikely+0x3fb): undefined reference to 'devlink_free'
Fix this by adding a dependency on MAY_USE_DEVLINK so that CONFIG_NET_DSA
get switched to be build as module when CONFIG_NET_DEVLINK=m.
Fixes: 96567d5dacf4 ("net: dsa: dsa2: Add basic support of devlink") Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 2 Apr 2017 03:04:04 +0000 (20:04 -0700)]
Merge branch 'phylib-EEE-updates'
Russell King says:
====================
phylib EEE updates
This series of patches depends on the previous set of changes, and is
therefore net-next material.
While testing the EEE code, I discovered a number of issues:
1. It is possible to enable advertisment of EEE modes which are not
supported by the hardware. We omit to check the supported modes
and mask off those modes that are not supported before writing the
EEE advertisment register.
2. We need to restart autonegotiation after a change of the EEE
advertisment, otherwise the link partner does not see the updated
EEE modes.
3. SGMII connected PHYs are also capable of supporting EEE.
Through discussion with Florian, it has been decided to remove the check
for the PHY interface mode in patch (3).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 31 Mar 2017 09:37:18 +0000 (10:37 +0100)]
net: phy: allow EEE with any interface mode
EEE is able to work in any PHY interface mode, there is nothing which
fundamentally restricts it to only a few modes. For example, EEE works
in SGMII mode with the Marvell 88E1512.
Rather than just adding SGMII mode to the list, Florian suggests
removing the list of interface modes entirely:
It actually sounds like we should just kill the check entirely,
it does not appear that any of the interface mode would not
fundamentally be able to support EEE, because the "lowest" mode
we support is MII, and even there it's quite possible to support
EEE.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 31 Mar 2017 09:37:12 +0000 (10:37 +0100)]
net: phy: restart phy autonegotiation after EEE advertisment change
When the EEE advertisment is changed, we should restart autonegotiation
to update the link partner with the new EEE settings. Add this trigger
but only if the advertisment has changed.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Clearly, this is not sane, we should only allow link modes that are
supported to be advertised (as we do elsewhere.) Ensure that we mask
the MDIO_AN_EEE_ADV value with the capabilities retrieved from the
MDIO_PCS_EEE_ABLE register.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 1 Apr 2017 19:45:58 +0000 (12:45 -0700)]
Merge branch 'bpf-prog-testing-framework'
Alexei Starovoitov says:
====================
bpf: program testing framework
Development and testing of networking bpf programs is quite cumbersome.
Especially tricky are XDP programs that attach to real netdevices and
program development feels like working on the car engine while
the car is in motion.
Another problem is ongoing changes to upstream llvm core
that can introduce an optimization that verifier will not
recognize. llvm bpf backend tests have no ability to run the programs.
To improve this situation introduce BPF_PROG_TEST_RUN command
to test and performance benchmark bpf programs.
It achieves several goals:
- development of xdp and skb based bpf programs can be done
in a canned environment with unit tests
- program performance optimizations can be benchmarked outside of
networking core (without driver and skb costs)
- continuous testing of upstream changes is finally practical
Patches 4,5,6 add C based test cases of various complexity
to cover some sched_cls and xdp features. More tests will
be added in the future. The tests were run on centos7 only.
For now the framework supports only skb and xdp programs. In the future
it can be extended to socket_filter and tracing program types.
More details are in individual patches.
v1->v2:
- rename bpf_program_test_run->bpf_prog_test_run
- add missing #include <linux/bpf.h> since libbpf.h shouldn't depend
on prior includes
- reordered patches 3 and 4 to keep bisect clean
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
selftests/bpf: add l4 load balancer test based on sched_cls
this l4lb demo is a comprehensive test case for LLVM codegen and
kernel verifier. It's using fully inlined jhash(), complex packet
parsing and multiple map lookups of different types to stress
llvm and verifier.
The map sizes, map population and test vectors are artificial to
exercise different paths through the bpf program.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests/bpf: add a test for basic XDP functionality
add C test for xdp_adjust_head(), packet rewrite and map lookups
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests/bpf: add a test for overlapping packet range checks
add simple C test case for llvm and verifier range check fix from
commit b1977682a385 ("bpf: improve verifier packet range checks")
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
expose bpf_program__set_type() to set program type
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tools/lib/bpf: add support for BPF_PROG_TEST_RUN command
add support for BPF_PROG_TEST_RUN command to libbpf.a
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Wang Nan <wangnan0@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
development and testing of networking bpf programs is quite cumbersome.
Despite availability of user space bpf interpreters the kernel is
the ultimate authority and execution environment.
Current test frameworks for TC include creation of netns, veth,
qdiscs and use of various packet generators just to test functionality
of a bpf program. XDP testing is even more complicated, since
qemu needs to be started with gro/gso disabled and precise queue
configuration, transferring of xdp program from host into guest,
attaching to virtio/eth0 and generating traffic from the host
while capturing the results from the guest.
Moreover analyzing performance bottlenecks in XDP program is
impossible in virtio environment, since cost of running the program
is tiny comparing to the overhead of virtio packet processing,
so performance testing can only be done on physical nic
with another server generating traffic.
Furthermore ongoing changes to user space control plane of production
applications cannot be run on the test servers leaving bpf programs
stubbed out for testing.
Last but not least, the upstream llvm changes are validated by the bpf
backend testsuite which has no ability to test the code generated.
To improve this situation introduce BPF_PROG_TEST_RUN command
to test and performance benchmark bpf programs.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 31 Mar 2017 01:43:21 +0000 (18:43 -0700)]
net: dsa: Mock-up driver
This patch adds support for a DSA mock-up driver which essentially does
the following:
- registers/unregisters 4 fixed PHYs to the slave network devices
- uses eth0 (configurable) as the master netdev
- registers the switch as a fixed MDIO device against the fixed MDIO bus
at address 31
- includes dynamic debug prints for dsa_switch_ops functions that can be
enabled to get call traces
This is a good way to test modular builds as well as exercise the DSA
APIs without requiring access to real hardware. This does not test the
data-path, although this could be added later on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 1 Apr 2017 19:22:59 +0000 (12:22 -0700)]
Merge branch 'mv88e6xxx-cross-chip-bridging'
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: program cross-chip bridging
The purpose of this patch series is to bring hardware cross-chip
bridging configuration to the DSA layer and the mv88e6xxx DSA driver.
Most recent Marvell switch chips have a Cross-chip Port Based VLAN Table
(PVT) used to restrict to which internal destination port an arbitrary
external source port is allowed to egress frames to.
The current behavior of the mv88e6xxx driver is to program this table
table with all ones, allowing any external ports to egress frames on any
internal ports. This means that carefully crafted Ethernet frames can
potentially bypass the user bridging configuration.
Patches 1 to 7 prepare the setup of this table and factorize the common
bits of both in-chip and cross-chip Marvell bridging code.
Patch 8 adds new optional cross-chip bridging operations to DSA switch.
Patch 9 switches the current behavior to program the table according to
the user bridging configuration when (cross-chip) ports get (un)bridged.
On a ZII Rev B board, bridging together the 3 user ports of both 88E6352
will result in the following PVTs on respectively switch 0 and switch 1:
Changes since v2:
- Define MV88E6XXX_MAX_PVT_SWITCHES and MV88E6XXX_MAX_PVT_PORTS
- use mv88e6xxx_g2_misc_4_bit_port instead of the 5-bit variant
- add Andrew's tags and reword commit 6/9
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 30 Mar 2017 21:37:15 +0000 (17:37 -0400)]
net: dsa: mv88e6xxx: add cross-chip bridging
Implement the DSA cross-chip bridging operations by remapping the local
ports an external source port can egress frames to, when this cross-chip
port joins or leaves a bridge.
The PVT is no longer configured with all ones allowing any external
frame to egress any local port. Only DSA and CPU ports, as well as
bridge group members, can egress frames on local ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 30 Mar 2017 21:37:13 +0000 (17:37 -0400)]
net: dsa: mv88e6xxx: remap existing bridge members
When a local port of a switch chip becomes a member of a bridge group,
we need to reprogram the Cross-chip Port Based VLAN Table (PVT) to allow
existing cross-chip bridge members to egress frames on the new ports.
There is no functional changes yet, since the PVT is still programmed
with all ones, allowing any external port to egress frames locally.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 30 Mar 2017 21:37:12 +0000 (17:37 -0400)]
net: dsa: mv88e6xxx: factorize in-chip bridge map
Factorize the code in the DSA port_bridge_{join,leave} routines used to
program the port VLAN map of all local ports of a given bridge group.
At the same time shorten the _mv88e6xxx_port_based_vlan_map to get rid
of the old underscore prefix naming convention.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 30 Mar 2017 21:37:11 +0000 (17:37 -0400)]
net: dsa: mv88e6xxx: rework in-chip bridging
All ports -- internal and external, for chips featuring a PVT -- have a
mask restricting to which internal ports a frame is allowed to egress.
Now that DSA exposes the number of ports and their bridge devices, it is
possible to extract the code generating the VLAN map and make it generic
so that it can be shared later with the cross-chip bridging code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 30 Mar 2017 21:37:10 +0000 (17:37 -0400)]
net: dsa: mv88e6xxx: allocate the number of ports
The current code allocates DSA_MAX_PORTS ports for a Marvell dsa_switch
structure. Provide the exact number of ports so the corresponding
ds->num_ports is accurate.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 30 Mar 2017 21:37:09 +0000 (17:37 -0400)]
net: dsa: mv88e6xxx: program the PVT with all ones
The Cross-chip Port Based VLAN Table (PVT) is currently initialized with
all ones, allowing any external ports to egress frames on local ports.
This commit implements the PVT access functions and programs the PVT
with all ones for the local switch ports only, instead of using the Init
operation. The current behavior is unchanged for the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 30 Mar 2017 21:37:08 +0000 (17:37 -0400)]
net: dsa: mv88e6xxx: use 4-bit port for PVT data
The Cross-chip Port Based VLAN Table (PVT) supports two indexing modes,
one using 5-bit for device and 4-bit for port, the other using 4-bit for
device and 5-bit for port, configured via the Global 2 Misc register.
Only 4 bits for the source port are needed when interconnecting 88E6xxx
switch devices since they all support less than 16 physical ports. The
full 5 bits are needed when interconnecting a device with 98DXxxx switch
devices since they support more than 16 physical ports.
Add a mv88e6xxx_pvt_setup helper to set the 4-bit port PVT mode, which
will be extended later to also initialize the PVT content.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 30 Mar 2017 21:37:07 +0000 (17:37 -0400)]
net: dsa: mv88e6xxx: move PVT description in info
Not all Marvell switch chips feature a Cross-chip Port VLAN Table (PVT).
Chips with a PVT use the same implementation, so a new mv88e6xxx_ops
member won't be necessary yet. Add a "pvt" boolean member to the
mv88e6xxx_info structure and kill the obsolete MV88E6XXX_FLAGS_PVT flag.
Add a mv88e6xxx_has_pvt helper to wrap future checks of that condition.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Thu, 30 Mar 2017 13:24:15 +0000 (16:24 +0300)]
dpaa_eth: use AVOIDBLOCK for Tx confirmation queues
The AVOIDBLOCK flag determines the Tx confirmation queues processing
to be redirected to any available CPU when the current one is slow
in processing them. This may result in a higher Tx confirmation
interrupt count but may reduce pressure on a certain CPU that with
the previous setting would process all Tx confirmation frames.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Manlunas [Thu, 30 Mar 2017 00:56:43 +0000 (17:56 -0700)]
vxlan: vxlan dev should inherit lowerdev's gso_max_size
vxlan dev currently ignores lowerdev's gso_max_size, which adversely
affects TSO performance of liquidio if it's the lowerdev. Egress TCP
packets' skb->len often exceed liquidio's advertised gso_max_size. This
may happen on other NIC drivers.
Fix it by assigning lowerdev's gso_max_size to that of vxlan dev. Might as
well do likewise for gso_max_segs.
Single flow TSO throughput of liquidio as lowerdev (using iperf3):
Before the patch: 139 Mbps
After the patch : 8.68 Gbps
Percent increase: 6,144 %
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: Satanand Burla <satananda.burla@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 30 Mar 2017 12:03:06 +0000 (14:03 +0200)]
sock: avoid dirtying sk_stamp, if possible
sock_recv_ts_and_drops() unconditionally set sk->sk_stamp for
every packet, even if the SOCK_TIMESTAMP flag is not set in the
related socket.
If selinux is enabled, this cause a cache miss for every packet
since sk->sk_stamp and sk->sk_security share the same cacheline.
With this change sk_stamp is set only if the SOCK_TIMESTAMP
flag is set, and is cleared for the first packet, so that the user
perceived behavior is unchanged.
This gives up to 5% speed-up under udp-flood with small packets.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In order to better manage the resources of the ibmvnic driver, this set of
patches creates a set of initialization and release routines for the
drivers resources. Additionally, some patches do some re-naming of the
affected routines so that there is a common naming scheme in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Fontenot [Thu, 30 Mar 2017 06:49:29 +0000 (02:49 -0400)]
ibmvnic: Cleanup failure path in ibmvnic_open
Now that ibmvnic_release_resources will clean up all of our resources
properly, even if they were not allocated, we can just call this
for failues in ibmvnic_open.
This patch also moves the ibmvnic_release_resources() routine up
in the file to avoid creating a forward declaration ad re-names it to
drop the ibmvnic prefix.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Fontenot [Thu, 30 Mar 2017 06:49:18 +0000 (02:49 -0400)]
ibmvnic: Merge the two release_sub_crq_queue routines
Keeping two routines for releasing sub crqs, one for when irqs are not
initialized and one for when they are, is a bit of overkill. Merge the
two routines to a common release routine that will check for an irq
and release it if needed.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Fontenot [Thu, 30 Mar 2017 06:49:06 +0000 (02:49 -0400)]
ibmvnic: Create init and release routines for the tx pool
Move the initialization and the release of the tx pool to their own routines,
and update them to do validation. This also adds validation to the release
of the long term buffer.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Fontenot [Thu, 30 Mar 2017 06:48:54 +0000 (02:48 -0400)]
ibmvnic: Update main crq initialization and release
Update the initialization and release routines for the crq queue so that
we validate the crq queue.
Additionally this updates the naming of the init and release routines
for the crq queue to drop the ibmvnic prefix. This matches the naming
for similar routines in the driver
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Fontenot [Wed, 29 Mar 2017 19:14:55 +0000 (15:14 -0400)]
ibmvnic: Remove debugfs support
The debugfs support in the ibmvnic driver is not, and never has been,
supported. Just remove it.
The work done in the debugfs code for the driver was part of the original
spec for the ibmvnic driver. The corresponding support for this from the
server side was never supported and has been dropped.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 29 Mar 2017 17:45:44 +0000 (10:45 -0700)]
bonding: refine bond_fold_stats() wrap detection
Some device drivers reset their stats at down/up events, possibly
fooling bonding stats, since they operate with relative deltas.
It is nearly not possible to fix drivers, since some of them compute the
tx/rx counters based on per rx/tx queue stats, and the queues can be
reconfigured (ethtool -L) between the down/up sequence.
Lets avoid accumulating 'negative' values that render bonding stats
useless.
It is better to lose small deltas, assuming the bonding stats are
fetched at a reasonable frequency.
Fixes: 5f0c5f73e5ef ("bonding: make global bonding stats more reliable") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 29 Mar 2017 15:33:55 +0000 (16:33 +0100)]
VSOCK: remove unnecessary ternary operator on return value
Rather than assign the positive errno values to ret and then
checking if it is positive and flip the sign, just return the
errno value.
Detected by CoverityScan, CID#986649 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Jorgen Hansen <jhansen@vmware.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wadim Egorov [Wed, 29 Mar 2017 12:12:19 +0000 (14:12 +0200)]
net: stmmac: dwmac-rk: Add handling for RGMII_ID/RXID/TXID
ATM dwmac-rk will always set and enable it's internal delay lines.
Using PHY internal delays in combination with the phy-mode
rgmii-id/rxid/txid was not possible. Only rgmii was supported.
Now we can disable rockchip's gmac delay lines and also use
rgmii-id/rxid/txid.
Tested only with a RK3288 based board.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de> Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin [Wed, 29 Mar 2017 05:05:40 +0000 (07:05 +0200)]
Revert "net: stmmac: enable multiple buffers"
The commit aff3d9eff843 ("net: stmmac: enable multiple buffers") breaks
numerous boards. while some patch exists for fixing some of it,
dwmac-sunxi is still broken with it.
Since this patch is very huge, it will be better to split it in smaller
part.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 29 Mar 2017 21:13:09 +0000 (14:13 -0700)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-03-29
This series contains updates to i40e and i40evf only.
Preethi changes the default driver mode of operation to descriptor
write-back for VF.
Alex cleans up and addresses several issues in the way that i40e handles
private flags. Modifies the driver to use the length of the packet
instead of the DD status bit to determine if a new descriptor is ready
to be processed. Refactors the driver by pulling the code responsible
for fetching the receive buffer and synchronizing DMA into a single
function. Also pulled the code responsible for handling buffer
recycling and page counting and distributed it through several functions,
so we can commonize the bits that handle either freeing or recycling the
buffers. Cleans up the code in preparation for us adding support for
build_skb(). Changed the way we handle the maximum frame size for the
receive path so it is more consistent with other drivers.
Paul enables XL722 to use the direct read/write method since it does not
support the AQ command to read/write the control register.
Christopher fixes a case where we miss an arq element if a new one is
added before we enable interrupts and exit the loop.
Jake cleans up a pointless goto statement. Also cleaned up a flag that
was not being used.
Carolyn does round 2 for adding a delay to the receive queue to
accommodate the hardware needs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Wed, 29 Mar 2017 09:22:17 +0000 (11:22 +0200)]
tipc: allow rdm/dgram socketpairs
for socketpairs using connectionless transport, we cache
the respective node local TIPC portid to use in subsequent
calls to send() in the socket's private data.
Signed-off-by: Erik Hugne <erik.hugne@gmail.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Wed, 29 Mar 2017 09:22:16 +0000 (11:22 +0200)]
tipc: add support for stream/seqpacket socketpairs
sockets A and B are connected back-to-back, similar to what
AF_UNIX does.
Signed-off-by: Erik Hugne <erik.hugne@gmail.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang [Wed, 29 Mar 2017 08:47:19 +0000 (16:47 +0800)]
net: mvneta: set rx mode during resume if interface is running
I found a bug by:
0. boot and start dhcp client
1. echo mem > /sys/power/state
2. resume back immediately
3. don't touch dhcp client to renew the lease
4. ping the gateway. No acks
Usually, after step2, the DHCP lease isn't expired, so in theory we
should resume all back. But in fact, it doesn't. It turns out
the rx mode isn't resumed correctly. This patch fixes it by adding
mvneta_set_rx_mode(dev) in the resume hook if interface is running.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 29 Mar 2017 18:24:21 +0000 (11:24 -0700)]
Merge tag 'mlx5e-pedit' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Or Gerlitz says:
====================
mlx5e-pedit 2017-03-28
This series adds support for offloading modifications of packet headers using
ConnectX-5 HW header re-write as an action applied during packet steering.
The offloaded SW mechanism is TC's pedit action. The offloading is
supported for E-Switch steering of VF traffic in the SRIOV
switchdev mode and for NIC (non eswitch) RX.
One use-case for this offload on virtual networks, is when the hypervisor
implements flow based router such as Open-Stack's DVR, where L2 headers
of guest packets re-written with routers' MAC addresses and the IP TTL
is decremented.
Another use case (which can be applied in parallel with routing) is
stateless NAT where guest L3/L4 headers are re-written.
The series is built as follows: the 1st six patches are preperations which
don't yet add new functionality, patches 7-8 add the FW APIs (data-structures
and commands) for header re-write, and patch nine allows offloading driver
to access pedit keys.
The 10th patch is somehow the core of the series, where we translate from
the pedit way to represent set of header modification elements to the FW
API for that same matter.
Once a set of HW modification is established, we register it with the FW
and get a modify header ID. When this ID is used with an action during
packet steering, the HW applies the header modification on the packet.
Patches 11 and 12 implement the above logic as an offload for pedit action
for the NIC and E-Switch use-cases.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing
and helping me testing this functionality on HW simulator, before it could
be done with FW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 28 Mar 2017 22:19:49 +0000 (15:19 -0700)]
net: mpls: Update lfib_nlmsg_size to skip deleted nexthops
A recent commit skips nexthops in a route if the device has been
deleted. Update lfib_nlmsg_size accordingly.
Reported-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Acked-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 28 Mar 2017 19:57:09 +0000 (12:57 -0700)]
net: phy: Allow building mdio-boardinfo into the kernel
mdio-boardinfo contains code that is helpful for platforms to register
specific MDIO bus devices independent of how CONFIG_MDIO_DEVICE or
CONFIG_PHYLIB will be selected (modular or built-in). In order to make
that possible, let's do the following:
- descend into drivers/net/phy/ unconditionally
- make mdiobus_setup_mdiodev_from_board_info() take a callback argument
which allows us not to expose the internal MDIO board info list and
mutex, yet maintain the logic within the same file
- relocate the code that creates a MDIO device into
drivers/net/phy/mdio_bus.c
- build mdio-boardinfo.o into the kernel as soon as MDIO_DEVICE is
defined (y or m)
Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs") Fixes: 648ea0134069 ("net: phy: Allow pre-declaration of MDIO devices") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Tue, 14 Mar 2017 17:15:27 +0000 (10:15 -0700)]
i40e/i40evf: Change the way we limit the maximum frame size for Rx
This patch changes the way we handle the maximum frame size for the Rx
path. Previously we were rounding up to 2K for a 1500 MTU and then brining
the max frame size down to MTU plus a fixed amount. With this patch
applied what we now do is limit the maximum frame to 1.5K minus the value
for NET_IP_ALIGN for standard MTU, and for any MTU greater than 1500 we
allow up to the maximum frame size. This makes the behavior more
consistent with the other drivers such as igb which had similar logic. In
addition it reduces the test matrix for MTU since we only have two max
frame sizes that are handled for Rx now.
Change-ID: I23a9d3c857e7df04b0ef28c64df63e659c013f3f Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 14 Mar 2017 17:15:26 +0000 (10:15 -0700)]
i40e/i40evf: Add legacy-rx private flag to allow fallback to old Rx flow
This patch adds a control which will allow us to toggle into and out of the
legacy Rx mode. The legacy Rx mode is what we currently do when performing
Rx. As I make further changes what should happen is that the driver will
fall back to the behavior for Rx as of this patch should the "legacy-rx"
flag be set to on.
Change-ID: I0342998849bbb31351cce05f6e182c99174e7751 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 14 Mar 2017 17:15:25 +0000 (10:15 -0700)]
i40e/i40evf: Break i40e_fetch_rx_buffer up to allow for reuse of frag code
This patch is meant to clean up the code in preparation for us adding
support for build_skb. Specifically we deconstruct i40e_fetch_buffer into
several functions so that those functions can later be reused when we add a
path for build_skb.
Specifically with this change we split out the code for adding a page to an
exiting skb.
Change-ID: Iab1efbab6b8b97cb60ab9fdd0be1d37a056a154d Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 14 Mar 2017 17:15:24 +0000 (10:15 -0700)]
i40e/i40evf: Pull out code for cleaning up Rx buffers
This patch pulls out the code responsible for handling buffer recycling and
page counting and distributes it through several functions. This allows us
to commonize the bits that handle either freeing or recycling the buffers.
As far as the page count tracking one change to the logic is that
pagecnt_bias is decremented as soon as we call i40e_get_rx_buffer. It is
then the responsibility of the function that pulls the data to either
increment the pagecnt_bias if the buffer can be recycled as-is, or to
update page_offset so that we are pointing at the correct location for
placement of the next buffer.
Change-ID: Ibac576360cb7f0b1627f2a993d13c1a8a2bf60af Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 14 Mar 2017 17:15:23 +0000 (10:15 -0700)]
i40e/i40evf: Pull code for grabbing and syncing rx_buffer from fetch_buffer
This patch pulls the code responsible for fetching the Rx buffer and
synchronizing DMA into a function, specifically called i40e_get_rx_buffer.
The general idea is to allow for better code reuse by pulling this out of
i40e_fetch_rx_buffer. We dropped a couple of prefetches since the time
between the prefetch being called and the data being accessed was too small
to be useful.
Change-ID: I4885fce4b2637dbedc8e16431169d23d3d7e79b9 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Tue, 14 Mar 2017 17:15:22 +0000 (10:15 -0700)]
i40e/i40evf: Use length to determine if descriptor is done
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
Change-ID: Iebdf9cdb36c454ef092df27199b92ad09c374231 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Fri, 10 Mar 2017 20:22:05 +0000 (12:22 -0800)]
i40e: remove FDIR_REQUIRES_REINIT driver flag
This flag hasn't been used since commit 1e1be8f622ee ("i40e: ATR policy
change to flush the table to clean stale ATR rules").
Lets simplify things and just remove it.
Change-ID: I76279d84db8a2fd96f445b96aa413059f9256879 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Fri, 10 Mar 2017 20:22:04 +0000 (12:22 -0800)]
i40e: remove a useless goto statement
The goto found here for when in MFP mode is pointless. It jumps to the
end of a series of if blocks. However, right after this statement is
a closing '}' for this if block, which will result in the program flow
going to the exact same location as the goto statement indicates. Thus,
regardless of whether we are in MFP mode, the program flow will resume
from the same location.
This arose due to various refactoring which did not notice that this
goto became essentially a no-op.
To properly understand this diff you will need to view a larger context
than is given by default.
Change-ID: I088f73c3831aa5c4e2281380c7a3ce605594300c Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e: Check for new arq elements before leaving the adminq subtask loop
Fix a case where we miss an arq element if a new one is added before we
enable interrupts and exit the arq subtask loop. This occurs frequently
with RDMA running on Windows VF and causes long delays that prevent SMB
from establishing connections.
Change-ID: I3e1c8b2b960c12857d9b8275bea2c1563674392e Signed-off-by: Christopher N Bednarz <christopher.n.bednarz@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e: use register for XL722 control register read/write
The XL722 doesn't support the AQ command to read/write the control
register so enable it to bypass the check and use the direct read/write
method.
Change-ID: Iefecc737b57207485c90845af5989d5af518bf16 Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 10 Mar 2017 20:22:01 +0000 (12:22 -0800)]
i40e: Clean up handling of private flags
This patch cleans up and addresses several issues in the way that i40e
handles private flags. Previously the code was choosing fixed bits and
trying to match them up with strings in a somewhat haphazard way. This
resulted in the possibility for adding a new bit and causing a mismatch as
the private flags are linear bits starting at 0, and the private flags in
the driver were split up over a group specific to the PF and a group that
was global.
What this change does is define an array of structs used to represent the
private flags. Contained within the structs are the bits necessary to know
which flags to set and/or clear depending on the state of the bit. By
doing this we can add new bits in the future with minimal overhead and
avoid creating possible mis-matches should we need to remove a flag based
on compile options.
Change-ID: Ia3214ab04f0ab2f70354ac0997a135f1d01b0acd Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Preethi Banala [Fri, 10 Mar 2017 20:22:00 +0000 (12:22 -0800)]
i40evf: enforce descriptor write-back mechanism for VF
The current driver mode is to use a write-back mechanism for the head
register which indicates transmit completions. The VF driver needs to be
able to work on hardware that exclusively uses descriptor write-back, so
change the default driver mode of operation to descriptor write-back for
VF. In our analysis, performance wasn't significantly different with
either write-back method.
Change-ID: Ia92e4ec77c2df8dc4515c71d53746d57d77759af Signed-off-by: Preethi Banala <preethi.banala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Wed, 29 Mar 2017 05:46:05 +0000 (22:46 -0700)]
Merge branch 'dsa-devlink'
Andrew Lunn says:
====================
break include loop and dsa devlink support
These two patches add very basic support for devlink to DSA, in
preparation for playing with dpipe.
The first patch is needed to break an include loop between
netdevice.h, dsa.h and devlink.h. We need to remove dsa.h from
netdevice.h. As a result, some files fail to compile, because they
require includes pulled in via dsa.h. So this patch adds a number of
includes in various places. The majority is within the network
subsystem, but cifs also needs a few fixes.
0-day has been chewing on this for over a day now, and not found any
breakage. But Arnd's randconfig might uncover something.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 28 Mar 2017 21:45:07 +0000 (23:45 +0200)]
net: dsa: dsa2: Add basic support of devlink
Register the switch and its ports with devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 28 Mar 2017 21:45:06 +0000 (23:45 +0200)]
net: break include loop netdevice.h, dsa.h, devlink.h
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 29 Mar 2017 05:32:43 +0000 (22:32 -0700)]
Merge branch 'netconf-delnetconf'
David Ahern says:
====================
netconf: Add support for RTM_DELNETCONF
netconf notifications are sent as devices register but not when they
are deleted leaving userspace caches out of sync. Add support for
RTM_DELNETCONF to ipv4, ipv6 and mpls.
MPLS is missing RTM_NEWNETCONF as devices are created, so add it as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 28 Mar 2017 21:28:05 +0000 (14:28 -0700)]
net: ipv6: Add support for RTM_DELNETCONF
Send RTM_DELNETCONF notifications when a device is deleted. The message only
needs the device index, so modify inet6_netconf_fill_devconf to skip devconf
references if it is NULL.
Allows a userspace cache to remove entries as devices are deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 28 Mar 2017 21:28:03 +0000 (14:28 -0700)]
net: devinet: Add support for RTM_DELNETCONF
Send RTM_DELNETCONF notifications when a device is deleted. The message only
needs the device index, so modify inet_netconf_fill_devconf to skip devconf
references if it is NULL.
Allows a userspace cache to remove entries as devices are deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor interrupt moderation code for flexibility because parameters are
different for 10G and 25G cards. Currently parameters (for 10G only) come
from macros compiled-in to the PF and VF drivers; fix it so that parameters
suitable for the card (10G or 25G) come from the NIC firmware via response
to a command.
Also bump up driver version to 1.5.1 to match newer NIC firmware version.
Signed-off-by: Prasad Kanneganti <prasad.kanneganti@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: Derek Chickles <derek.chickles@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Tue, 28 Mar 2017 19:10:36 +0000 (15:10 -0400)]
net: dsa: fix copyright holder
I do not hold the copyright of the DSA core and drivers source files,
since these changes have been written as an initiative of my day job.
Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Tue, 28 Mar 2017 19:09:43 +0000 (15:09 -0400)]
net: dsa: mv88e6xxx: unconditionally set ATU trunk
Set the trunk member of the mv88e6xxx_atu_entry structure regardless its
value, so that uninitialized structures gets the correct boolean value.
Note that no mainline code is affected by the current behavior.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We don't support 88E6391 anywhere in the code, so remove the unused
mv88e6391_ops structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_info structure for the 88E6191 chip was pointing the
mv88e6391_ops definition instead of mv88e6191_ops. Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
The related mv88e6xxx_ops structure was misplaced. Reorder it correctly
to fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
The related mv88e6xxx_ops and mv88e6xxx_info structure were misplaced.
Reorder them correctly to fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 29 Mar 2017 01:05:24 +0000 (18:05 -0700)]
Merge branch 'qed-load-unload-mfw'
Yuval Mintz says:
====================
qed: load/unload mfw series
This series correct the unload flow and greatly enhances its
initialization flow in regard to interactions between driver
and management firmware.
Patch #1 makes sure unloading is done under management-firmware's
'criticial section' protection.
Patches #2 - #4 move driver into using a newer scheme for loading
in regard to the MFW; This newer scheme would help cleaning the device
in case a previous instance has dirtied it [preboot, PDA, etc.].
Patches #5 - #6 let driver inform management-firmware on number of
resources which are dependent on the non-management firmware used.
Patch #7 then uses a new resource [BDQ] instead of some set value.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tomer Tayar [Tue, 28 Mar 2017 12:12:55 +0000 (15:12 +0300)]
qed: Utilize resource-lock based scheme
Management firmware is used as an arbiter between the various PFs
in matters of resources, but some of the resources that need to
be divided are dependent on the non-management firmware used,
so management firmware first needs to be told how many resources
there are before trying to divide them.
As part of the initialization sequence, driver would first inform
the management firmware of the available resources under
a dedicated resource lock, and afterwards request for various
resources which might be based on the previous set values.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomer Tayar [Tue, 28 Mar 2017 12:12:54 +0000 (15:12 +0300)]
qed: Support management-based resource locking
Global locking can't properly be used to synchronize between different
PFs in all scenarios, as those instances might reside in different
logical partitions [e.g., when a PF is assigned via PDA to some VM].
The management firmware provides a generic infrastructure for
device locks. For each 'resource', it's guaranteed it could be acquired
by at most a single PF at any given time [or by management firmware].
This patch adds the necessary logic in qed for utilizing said
infrastructure, implementing lock/unlock internal APIs.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mintz, Yuval [Tue, 28 Mar 2017 12:12:53 +0000 (15:12 +0300)]
qed: Send pf-flr as part of initialization
During HW initialization, driver would set various registers to their
needed values - but it assumes all registers start at their reset-value,
so there's no need to re-configure a register's default value.
This assumption might be incorrect, e.g., in case of preboot driver
running and initializing the driver prior to our driver.
To overcome this, we now ask management firmware to initiate a PF-flr
early during the initialization sequence. That would return everything
in the PF's scope back to default and prevent previous configurations
from still being applied.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log