The floppy driver requests an I/O port it doesn't need, and sometimes this
causes a conflict with a motherboard device reported by PNPBIOS.
This patch makes the floppy driver request and release only the ports it
actually uses. It also factors out the request/release stuff and the
io-ports list so they're all in one place now.
but it requests 0x3f2-0x3f5 and 0x3f7, which includes the unused port
0x3f3.
Some BIOSes report 0x3f3 as a motherboard resource. The PNP system driver
reserves that, which causes a conflict when the floppy driver requests
0x3f2-0x3f5 later.
Philippe reported that this conflict broke the floppy driver between
2.6.11 and 2.6.22. His PNPBIOS reports these devices:
$ cat 00:03/id 00:03/resources # floppy device
PNP0700
state = active
io 0x3f4-0x3f5
io 0x3f2-0x3f2
Reference:
http://lkml.org/lkml/2009/1/31/162
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Philippe De Muyter <phdm@macqel.be> Reported-by: Philippe De Muyter <phdm@macqel.be> Tested-by: Philippe De Muyter <phdm@macqel.be> Cc: Adam M Belay <abelay@mit.edu> Cc: Robert Hancock <hancockrwd@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The missing device table means that the floppy module is not auto-loaded,
even when the appropriate PNP device (0700) is found.
We don't actually use the table in the module, since the device doesn't
have a struct pnp_driver, but it's sufficient to cause an alias in the
module that udev/modprobe will use.
Signed-off-by: Scott James Remnant <scott@canonical.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Philippe De Muyter <phdm@macqel.be> Acked-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michael Tokarev reported receiving a large packet could crash
a machine with RTL8169 NIC.
( original thread at http://lkml.org/lkml/2009/6/8/192 )
Problem is this driver tells that NIC frames up to 16383 bytes
can be received but provides skb to rx ring allocated with
smaller sizes (1536 bytes in case standard 1500 bytes MTU is used)
When a frame larger than what was allocated by driver is received,
dma transfert can occurs past the end of buffer and corrupt
kernel memory.
Fix is to tell to NIC what is the maximum size a frame can be.
This bug is very old, (before git introduction, linux-2.6.10), and
should be backported to stable versions.
Reported-by: Michael Tokarev <mjt@tls.msk.ru> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Michael Tokarev <mjt@tls.msk.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit code, we scan buffers attached to a transaction. During this
scan, we sometimes have to drop j_list_lock and then we recheck whether
the journal buffer head didn't get freed by journal_try_to_free_buffers().
But checking for buffer_jbd(bh) isn't enough because a new journal head
could get attached to our buffer head. So add a check whether the journal
head remained the same and whether it's still at the same transaction and
list.
This is a nasty bug and can cause problems like memory corruption (use after
free) or trigger various assertions in JBD code (observed).
Signed-off-by: Jan Kara <jack@suse.cz> Cc: <linux-ext4@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peer reported:
| The bug is introduced from kernel 2.6.27, if E820 table reserve the memory
| above 4G in 32bit OS(BIOS-e820: 00000000fff80000 - 0000000120000000
| (reserved)), system will report Int 6 error and hang up. The bug is caused by
| the following code in drivers/firmware/memmap.c, the resource_size_t is 32bit
| variable in 32bit OS, the BUG_ON() will be invoked to result in the Int 6
| error. I try the latest 32bit Ubuntu and Fedora distributions, all hit this
| bug.
|======
|static int firmware_map_add_entry(resource_size_t start, resource_size_t end,
| const char *type,
| struct firmware_map_entry *entry)
and it only happen with CONFIG_PHYS_ADDR_T_64BIT is not set.
it turns out we need to pass u64 instead of resource_size_t for that.
[akpm@linux-foundation.org: add comment] Reported-and-tested-by: Peer Chen <pchen@nvidia.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Cc: Ingo Molnar <mingo@elte.hu> Acked-by: H. Peter Anvin <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a bug in the mxser kernel module that still appears in the
2.6.29.4 kernel.
mxser_get_ISA_conf takes a ioaddress as its first argument, by passing the
not of the ioaddr, you're effectively passing 0 which means it won't be
able to talk to an ISA card. I have tested this, and removing the !
fixes the problem.
In moxa.c there are 32 minor numbers reserved for each device. The number
of ports actually available per device is stored in
moxa_board_conf->numPorts. This number is not considered in moxa_open().
Opening a port that is not available results in a kernel oops. This patch
adds a test to moxa_open() that prevents opening unavailable ports.
Some users still load bond module multiple times to create bonding
devices. This accidentally was broken by a later patch about
the time sysfs was fixed. According to Jay, it was broken
by:
commit b8a9787eddb0e4665f31dd1d64584732b2b5d051
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Fri Jun 13 18:12:04 2008 -0700
bonding: Allow setting max_bonds to zero
Note: sysfs and procfs still produce WARN() messages when this is done
so the sysfs method is the recommended API.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove wrong fifo size definition for some AT91 products.
Due to a misunderstanding of some AT91 datasheets, a fifo size of 2048
(words) has been introduced by mistake. In fact, all products (AT91/AT32)
are sharing the same fifo size of 512 words.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
netmos serial/parallel adapters come in different flavour differing only
by the number of parallel and serial ports, which are encoded in the
subdevice ID.
Last fix of Christian Pellegrin for 9855 2P2S broke support for 9855 1P4S,
and works only by side-effect for the first parallel port of a 2P2S, as
this first parallel port is found by reading the second addr entry of
(struct parport_pc_pci) cards[netmos_9855], which is not initialized, and
hence has value 0, which happens to be the BAR of the first parallel port.
netmos_9xx5_combo entry in (struct parport_pc_pci) cards[], which is used
for a 9845 1P4S must also be fixed for the parallel port support when
there are 4 serial ports because this entry currently gives 2 as BAR index
for the parallel port. Actually, in this case, BAR 2 is the 3rd serial
port while the parallel port is at BAR 4.
I fixed 9845 1P4S and 9855 1P4S support, while preserving 9855 2P2S support,
- by creating a netmos_9855_2p entry and using it for 9855 boards with 2
parallel ports : 9855 2P2S and 9855 2P0S boards,
- and by allowing netmos_parallel_init to change not only the number of
parallel ports (0 or 1), but making it also change the BAR index of the
parallel port when the serial ports are before the parallel port.
PS: the netmos_9855_2p entry in (struct pciserial_board)
pci_parport_serial_boards[] is needed because netmos_parallel_init has no
clean way to replace FL_BASE2 by FL_BASE4 in the description of the serial
ports in function of the number of parallel ports on the card.
Tested with 9845 1P4S, 9855 1P4S and 9855 2P2S boards.
Signed-off-by: Philippe De Muyter <phdm@macqel.be> Tested-by: Christian Pellegrin <chripell@fsfe.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If two CPU's simultaneously call ext4_ext_get_blocks() at the same
time, there is nothing protecting the i_cached_extent structure from
being used and updated at the same time. This could potentially cause
the wrong location on disk to be read or written to, including
potentially causing the corruption of the block group descriptors
and/or inode table.
This bug has been in the ext4 code since almost the very beginning of
ext4's development. Fortunately once the data is stored in the page
cache cache, ext4_get_blocks() doesn't need to be called, so trying to
replicate this problem to the point where we could identify its root
cause was *extremely* difficult. Many thanks to Kevin Shanahan for
working over several months to be able to reproduce this easily so we
could finally nail down the cause of the corruption.
The BH_Unwritten flag indicates that the buffer is allocated on disk
but has not been written; that is, the disk was part of a persistent
preallocation area. That flag should only be set when a get_blocks()
function is looking up a inode's logical to physical block mapping.
When ext4_get_blocks_wrap() is called with create=1, the uninitialized
extent is converted into an initialized one, so the BH_Unwritten flag
is no longer appropriate. Hence, we need to make sure the
BH_Unwritten is not left set, since the combination of BH_Mapped and
BH_Unwritten is not allowed; among other things, it will result ext4's
get_block() to be called over and over again during the write_begin
phase of write(2).
Use a very large unsigned number (~0xffff) as as the fake block number
for the delayed new buffer. The VFS should never try to write out this
number, but if it does, this will make it obvious.
We need to mark the buffer_head mapping preallocated space as new
during write_begin. Otherwise we don't zero out the page cache content
properly for a partial write. This will cause file corruption with
preallocation.
Now that we mark the buffer_head new we also need to have a valid
buffer_head blocknr so that unmap_underlying_metadata() unmaps the
correct block.
Don't try to look at i_file_acl_high unless the INCOMPAT_64BIT feature
bit is set. The field is normally zero, but older versions of e2fsck
didn't automatically check to make sure of this, so in the spirit of
"be liberal in what you accept", don't look at i_file_acl_high unless
we are using a 64-bit filesystem.
If the block containing external extended attributes (which is stored
in i_file_acl and i_file_acl_high) is larger than the on-disk
filesystem, the process which tried to access the extended attributes
will endlessly issue kernel printks complaining that
"__find_get_block_slow() failed", locking up that CPU until the system
is forcibly rebooted.
So when we read in the inode, make sure the i_file_acl value is legal,
and if not, flag the filesystem as being corrupted.
Update information about locking in JBD2 revoke code. Inconsistency in
comments found by Lin Tan <tammy000@gmail.com>
CC: Lin Tan <tammy000@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With delayed allocation we should not/cannot discard inode prealloc
space during file close. We would still have dirty pages for which we
haven't allocated blocks yet. With this fix after each get_blocks
request we check whether we have zero reserved blocks and if yes and
we don't have any writers on the file we discard inode prealloc space.
When renaming a file such that a link to another inode is overwritten,
force any delay allocated blocks that to be allocated so that if the
filesystem is mounted with data=ordered, the data blocks will be
pushed out to disk along with the journal commit. Many application
programs expect this, so we do this to avoid zero length files if the
system crashes unexpectedly.
When closing a file that had been previously truncated, force any
delay allocated blocks that to be allocated so that if the filesystem
is mounted with data=ordered, the data blocks will be pushed out to
disk along with the journal commit. Many application programs expect
this, so we do this to avoid zero length files if the system crashes
unexpectedly.
Add an ioctl which forces all of the delay allocated blocks to be
allocated. This also provides a function ext4_alloc_da_blocks() which
will be used by the following commits to force files to be fully
allocated to preserve application-expected ext3 behaviour.
Some poeple are reading the ext4 feature list too literally and create
dubious test cases involving very long filenames and 1k blocksize and
then complain when they run into an htree-imposed limit. So add fine
print to the "fix 32000 subdirectory limit" ext4 feature.
ext4_iget() returns -ESTALE if invoked on a deleted inode, in order to
report errors to NFS properly. However, in ext4_lookup(), this
-ESTALE can be propagated to userspace if the filesystem is corrupted
such that a directory entry references a deleted inode. This leads to
a misleading error message - "Stale NFS file handle" - and confusion
on the part of the admin.
The bug can be easily reproduced by creating a new filesystem, making
a link to an unused inode using debugfs, then mounting and attempting
to ls -l said link.
This patch thus changes ext4_lookup to return -EIO if it receives
-ESTALE from ext4_iget(), as ext4 does for other filesystem metadata
corruption; and also invokes the appropriate ext*_error functions when
this case is detected.
At the moment there are few restrictions on which flags may be set on
which inodes. Specifically DIRSYNC may only be set on directories and
IMMUTABLE and APPEND may not be set on links. Tighten that to disallow
TOPDIR being set on non-directories and only NODUMP and NOATIME to be set
on non-regular file, non-directories.
Introduces a flags masking function which masks flags based on mode and
use it during inode creation and when flags are set via the ioctl to
facilitate future consistency.
At present INDEX and EXTENTS are the only flags that new ext4 inodes do
NOT inherit from their parent. In addition prevent the flags DIRTY,
ECOMPR, IMAGIC, TOPDIR, HUGE_FILE and EXT_MIGRATE from being inherited.
List inheritable flags explicitly to prevent future flags from
accidentally being inherited.
This fixes the TOPDIR flag inheritance bug reported at
http://bugzilla.kernel.org/show_bug.cgi?id=9866.
so it's critical that we get the right group number back for
this prealloc context, to lock the right group (the one
associated with this pa) and prevent concurrent list manipulation.
however, ext4_mb_put_pa() passes in (pa->pa_pstart - 1) with a
comment, "-1 is to protect from crossing allocation group".
This makes sense for the group_pa, where pa_pstart is advanced
by the length which has been used (in ext4_mb_release_context()),
and when the entire length has been used, pa_pstart has been
advanced to the first block of the next group.
However, for inode_pa, pa_pstart is never advanced; it's just
set once to the first block in the group and not moved after
that. So in this case, if we subtract one in ext4_mb_put_pa(),
we are actually locking the *previous* group, and opening the
race with the other threads which do not subtract off the extra
block.
oopsed, with a BUG_ON in ext4_mb_normalize_request because
size == EXT4_BLOCKS_PER_GROUP
It appears to me (esp. after talking to Andreas) that the BUG_ON
is bogus; a request of exactly EXT4_BLOCKS_PER_GROUP should
be allowed, though larger sizes do indicate a problem.
Fix that an another (apparently rare) codepath with a similar check.
The ext4_ext_search_right() function is confusing; it uses a
"depth" variable which is 0 at the root and maximum at the leaves,
but the on-disk metadata uses a "depth" (actually eh_depth) which
is opposite: maximum at the root, and 0 at the leaves.
The ext4_ext_check_header() function is given a depth and checks
the header agaisnt that depth; it expects the on-disk semantics,
but we are giving it the opposite in the while loop in this
function. We should be giving it the on-disk notion of "depth"
which we can get from (p_depth - depth) - and if you look, the last
(more commonly hit) call to ext4_ext_check_header() does just this.
Sending in the wrong depth results in (incorrect) messages
about corruption:
EXT4-fs error (device sdb1): ext4_ext_search_right: bad header
in inode #2621457: unexpected eh_depth - magic f30a, entries 340,
max 340(0), depth 1(2)
http://bugzilla.kernel.org/show_bug.cgi?id=12821
Reported-by: David Dindorp <ddi@dubex.dk> Signed-off-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I believe that this is because ext4_free_inode() uses atomic
bitops, and although ext4_new_inode() *used* to also use atomic
bitops for synchronization, commit 393418676a7602e1d7d3f6e560159c65c8cbd50e changed this to use
the sb_bgl_lock, so that we could also synchronize against
read_inode_bitmap and initialization of uninit inode tables.
However, that change left ext4_free_inode using atomic bitops,
which I think leaves no synchronization between setting &
unsetting bits in the inode table.
The below patch fixes it for me, although I wonder if we're
getting at all heavy-handed with this spinlock...
pid doesn't count with some band having more bitrates than the one
associated the first time.
Fix that by counting the maximal available bitrate count and allocate
big enough space.
Secondly, fix touching uninitialized memory which causes panics.
Index sucked from this random memory points to the hell.
The fix is to sort the rates on each band change.
Also remove a comment which is wrong now.
This version also contains half of
mac80211: avoid NULL ptr deref when finding max_rates in PID and minstrel
patch by John W. Linville, which is namely:
- if (sband->n_bitrates > max_rates)
+ if (sband && sband->n_bitrates > max_rates)
to fix oopses on one band devices.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DMI tables are loaded by EFI, so the dmi calls must happen after
efi_init() and not before.
Currently Apple hardware uses DMI to determine the framebuffer mappings
for efifb. Without DMI working you also have no video on MacBook Pro.
This patch resolves the DMI issue for EFI hardware (DMI is now properly
detected at boot), and additionally efifb now loads on Apple hardware
(i.e. video works).
Signed-off-by: Brian Maly <bmaly@redhat> Acked-by: Yinghai Lu <yinghai@kernel.org> Cc: ying.huang@intel.com
LKML-Reference: <49ADEDA3.1030406@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
V4L/DVB (10943): cx88: Prevent general protection fault on rmmod
When unloading the cx8800 driver I sometimes get a general protection
fault. Analysis revealed a race in cx88_ir_stop(). It can be solved by
using a delayed work instead of a timer for infrared input polling.
Pascal reported and bisected a commit:
| x86/PCI: don't call e820_all_mapped with -1 in the mmconfig case
which broke one system system.
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255
PCI: MCFG area at f0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
it didn't have
PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
anymore, and try to use 0xf000000 - 0xffffffff for mmconfig
For 32bit, mcfg_res->end could be 32bit only (if 64 resources aren't used)
So use end - 1 to pass the value in mcfg->end to avoid overflow.
We don't need to worry about the e820 path, they are always 64 bit.
On x86 and x86-64, it is possible that page tables are shared beween
shared mappings backed by hugetlbfs. As part of this,
page_table_shareable() checks a pair of vma->vm_flags and they must match
if they are to be shared. All VMA flags are taken into account, including
VM_LOCKED.
The problem is that VM_LOCKED is cleared on fork(). When a process with a
shared memory segment forks() to exec() a helper, there will be shared
VMAs with different flags. The impact is that the shared segment is
sometimes considered shareable and other times not, depending on what
process is checking.
What happens is that the segment page tables are being shared but the
count is inaccurate depending on the ordering of events. As the page
tables are freed with put_page(), bad pmd's are found when some of the
children exit. The hugepage counters also get corrupted and the Total and
Free count will no longer match even when all the hugepage-backed regions
are freed. This requires a reboot of the machine to "fix".
This patch addresses the problem by comparing all flags except VM_LOCKED
when deciding if pagetables should be shared or not for hugetlbfs-backed
mapping.
Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk> Cc: Ingo Molnar <mingo@elte.hu> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: <starlight@binnacle.cx> Cc: Eric B Munson <ebmunson@us.ibm.com> Cc: Adam Litke <agl@us.ibm.com> Cc: Andy Whitcroft <apw@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The option driver (and presumably others) allocates several URBs when it
opens and tries to free them when it closes. The isp1760_urb_dequeue
function gets called, but the packet being dequeued is not necessarily at
the
front of one of the 32 queues. If not, the isp1760_urb_done function doesn't
get called for the URB and the process trying to free it hangs forever on a
wait_queue. This patch does two things. If the URB being dequeued has others
queued behind it, it re-queues them. And it searches the queues looking for
the URB being dequeued rather than just looking at the one at the front of
the queue.
Kernel 2.6.18 broke the MotU Fastlane, which uses duplicate endpoint
numbers in a manner that is not only illegal but also confuses the
kernel's endpoint descriptor caching mechanism. To work around this, we
have to add a separate usb_set_interface() call to guide the USB core to
the correct descriptors.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-and-tested-by: David Fries <david@fries.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eric Paris [Mon, 1 Jun 2009 14:21:05 +0000 (10:21 -0400)]
SELinux: BUG in SELinux compat_net code
This patch is not applicable to Linus's tree as the code in question has
been removed for 2.6.30. I'm sending in case any of the stable
maintainers would like to push to their branches (which I think anything
pre 2.6.30 would like to do).
Ubuntu users were experiencing a kernel panic when they enabled SELinux
due to an old bug in our handling of the compatibility mode network
controls, introduced Jan 1 2008 effad8df44261031a882e1a895415f7186a5098e
Most distros have not used the compat_net code since the new code was
introduced and so noone has hit this problem before. Ubuntu is the only
distro I know that enabled that legacy cruft by default. But, I was ask
to look at it and found that the above patch changed a call to
avc_has_perm from if(send_perm) to if(!send_perm) in
selinux_ip_postroute_iptables_compat(). The result is that users who
turn on SELinux and have compat_net set can (and oftern will) BUG() in
avc_has_perm_noaudit since they are requesting 0 permissions.
This patch corrects that accidental bug introduction.
Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Martin Knoblauch reports that trying to build 2.6.30-rc6-git3 with
RHEL4.3 userspace (gcc (GCC) 3.4.5 20051201 (Red Hat 3.4.5-2)) causes an
internal compiler error (ICE):
and after some debugging it turns out that it's due to the code trying
to figure out the rough value of the current stack pointer by taking an
address of an uninitialized variable and casting that to an integer.
This is clearly a compiler bug, but it's not worth fighting - while the
current stack kernel pointer might be somewhat hard to predict in user
space, it's also not generally going to change for a lot of the call
chains for a particular process.
So just drop it, and mumble some incoherent curses at the compiler.
Tested-by: Martin Knoblauch <spamtrap@knobisoft.de> Cc: Matt Mackall <mpm@selenic.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's a really simple patch that basically just open-codes the current
"secure_ip_id()" call, but when open-coding it we now use a _static_
hashing area, so that it gets updated every time.
And to make sure somebody can't just start from the same original seed of
all-zeroes, and then do the "half_md4_transform()" over and over until
they get the same sequence as the kernel has, each iteration also mixes in
the same old "current->pid + jiffies" we used - so we should now have a
regular strong pseudo-number generator, but we also have one that doesn't
have a single seed.
Note: the "pid + jiffies" is just meant to be a tiny tiny bit of noise. It
has no real meaning. It could be anything. I just picked the previous
seed, it's just that now we keep the state in between calls and that will
feed into the next result, and that should make all the difference.
I made that hash be a per-cpu data just to avoid cache-line ping-pong:
having multiple CPU's write to the same data would be fine for randomness,
and add yet another layer of chaos to it, but since get_random_int() is
supposed to be a fast interface I did it that way instead. I considered
using "__raw_get_cpu_var()" to avoid any preemption overhead while still
getting the hash be _mostly_ ping-pong free, but in the end good taste won
out.
hugetlbfs reserves huge pages but does not fault them at mmap() time to
ensure that future faults succeed. The reservation behaviour differs
depending on whether the mapping was mapped MAP_SHARED or MAP_PRIVATE.
For MAP_SHARED mappings, hugepages are reserved when mmap() is first
called and are tracked based on information associated with the inode.
Other processes mapping MAP_SHARED use the same reservation. MAP_PRIVATE
track the reservations based on the VMA created as part of the mmap()
operation. Each process mapping MAP_PRIVATE must make its own
reservation.
hugetlbfs currently checks if a VMA is MAP_SHARED with the VM_SHARED flag
and not VM_MAYSHARE. For file-backed mappings, such as hugetlbfs,
VM_SHARED is set only if the mapping is MAP_SHARED and the file was opened
read-write. If a shared memory mapping was mapped shared-read-write for
populating of data and mapped shared-read-only by other processes, then
hugetlbfs would account for the mapping as if it was MAP_PRIVATE. This
causes processes to fail to map the file MAP_SHARED even though it should
succeed as the reservation is there.
This patch alters mm/hugetlb.c and replaces VM_SHARED with VM_MAYSHARE
when the intent of the code was to check whether the VMA was mapped
MAP_SHARED or MAP_PRIVATE.
Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk> Cc: Ingo Molnar <mingo@elte.hu> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: <starlight@binnacle.cx> Cc: Eric B Munson <ebmunson@us.ibm.com> Cc: Adam Litke <agl@us.ibm.com> Cc: Andy Whitcroft <apw@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jeff Kirsher [Tue, 2 Jun 2009 23:38:52 +0000 (16:38 -0700)]
igb: fix LRO warning
This fix is only needed for 2.6.29.y tree, since in 2.6.30 and later IGB
has moved to using GRO instead of LRO.
igb supports LRO, but was not setting any hooks to the ->set_flags
ethtool_ops function. This would trigger warnings if the user tried
to enable or disable LRO.
Based on the patch provided by Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Sergey Kononenko <sergk@sergk.org.ua> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch to fix bad length checking in e1000. E1000 by default does two
things:
1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put
Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set. This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test). If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb. This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU. The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000. This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Tested-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When AMD C1E is enabled, local APIC timer will stop even in C1. To avoid
suspend/resume hang, this patch removes C1 and replace it with a cpu_relax() in
suspend/resume path. This hasn't any impact in runtime path.
http://bugzilla.kernel.org/show_bug.cgi?id=13233
[ impact: avoid suspend/resume hang in AMD CPU with C1E enabled ]
Tested-by: Dmitry Lyzhyn <thisistempbox@yahoo.com> Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add barrier() to bnx2_get_hw_{tx|rx}_cons() to fix this issue:
http://bugzilla.kernel.org/show_bug.cgi?id=12698
This issue was reported by multiple i386 users. Without barrier(),
the compiled code looks like the following where %eax contains the
address of the tx_cons or rx_cons in the DMA status block. The
status block contents can change between the cmpb and the movzwl
instruction. The driver would crash if the value was not 0xff during
the cmpb instruction, but changed to 0xff during the movzwl
instruction.
Thanks to Pascal de Bruijn <pmjdebruijn@pcode.nl> for reporting the
problem and Holger Noefer <hnoefer@pironet-ndh.com> for patiently
testing test patches for us.
[greg - took out version change]
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following regression that occurred during the
scsi_dma_map()/unmap()
changes when compiling with CONFIG_DMA_API_DEBUG=y :
WARNING: at lib/dma-debug.c:496 check_unmap+0x142/0x542()
Hardware name:
3w-xxxx 0000:02:02.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000000000000] [size=36
bytes]
Signed-off-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A long-standing feature in tcp_init_metrics() is such that
any of its goto reset prevents call to tcp_init_cwnd().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When called with a consumed value that is less than skb_headlen(skb)
bytes into a page frag, skb_seq_read() incorrectly returns an
offset/length relative to skb->data. Ensure that data which should come
from a page frag does.
Signed-off-by: Thomas Chenault <thomas_chenault@dell.com> Tested-by: Shyam Iyer <shyam_iyer@dell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
typo -- pkt_dev->nflows is for stats only, the number of concurrent
flows is stored in cflows.
Reported-By: Vladimir Ivashchenko <hazard@francoudi.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check whether the underlying device provides a set of ethtool ops before
checking for individual handlers to avoid NULL pointer dereferences.
Reported-by: Art van Breemen <ard@telegraafnet.nl> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix locking issue in alb MAC address management; removed
incorrect locking and replaced with correct locking. This bug was
introduced in commit 059fe7a578fba5bbb0fdc0365bfcf6218fa25eb0
("bonding: Convert locks to _bh, rework alb locking for new locking")
Bug reported by Paul Smith <paul@mad-scientist.net>, who also
tested the fix.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Otherwise it might interrupt switch_to() midstream and use
half-cooked register window state.
Reported-by: Chris Torek <chris.torek@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sparc64 SBUS and PCI controllers use a combination of IMAP and ICLR
registers to manage device interrupts.
The IMAP register contains the "valid" enable bit as well as CPU
targetting information. Whereas the ICLR register is written with
zero at the end of handling an interrupt to reset the state machine
for that interrupt to IDLE so it can be sent again.
For PCI slot and SBUS slot devices we can have multiple interrupts
sharing the same IMAP register. There are individual ICLR registers
but only one IMAP register for managing those.
We represent each shared case with individual virtual IRQs so the
generic IRQ layer thinks there is only one user of the IRQ instance.
In such shared IMAP cases this is wrong, so if there are multiple
active users then a free_irq() call will prematurely turn off the
interrupt by clearing the Valid bit in the IMAP register even though
there are other active users.
Fix this by simply doing nothing in sun4u_disable_irq() and checking
IRQF_DISABLED during IRQ dispatch.
This situation doesn't exist in the hypervisor sun4v cases, so I left
those alone.
Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When you compile kernel on Sparc64 with heap memory checking and type
"cat /proc/iomem", you get a crash, because pointers in struct
resource are uninitialized.
Most code fills struct resource with zeros, so I assume that it is
responsibility of the caller of request_resource to initialized it,
not the responsibility of request_resource functuion.
After 2.6.29 is out, there could be a check for uninitialized fields
added to request_resource to avoid crashes like this.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> CPU 0 is running the context, task->mm == task->active_mm == your
> context. The CPU is in userspace happily churning things.
>
> CPU 1 used to run it, not anymore, it's now running fancyfsd which
> is a kernel thread, but current->active_mm still points to that
> same context.
>
> Because there's only one "real" user, mm_users is 1 (but mm_count is
> elevated, it's just that the presence on CPU 1 as active_mm has no
> effect on mm_count().
>
> At this point, fancyfsd decides to invalidate a mapping currently mapped
> by that context, for example because a networked file has changed
> remotely or something like that, using unmap_mapping_ranges().
>
> So CPU 1 goes into the zapping code, which eventually ends up calling
> flush_tlb_pending(). Your test will succeed, as current->active_mm is
> indeed the target mm for the flush, and mm_users is indeed 1. So you
> will -not- send an IPI to the other CPU, and CPU 0 will continue happily
> accessing the pages that should have been unmapped.
To fix this problem, check ->mm instead of ->active_mm, and this
means:
> So if you test current->mm, you effectively account for mm_users == 1,
> so the only way the mm can be active on another processor is as a lazy
> mm for a kernel thread. So your test should work properly as long
> as you don't have a HW that will do speculative TLB reloads into the
> TLB on that other CPU (and even if you do, you flush-on-switch-in should
> get rid of any crap here).
And therefore we should be OK.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David S. Miller [Tue, 26 May 2009 22:56:18 +0000 (15:56 -0700)]
sparc: Fix bus type probing for ESP and LE devices.
If there is a dummy "espdma" or "ledma" parent device above ESP scsi
or LE ethernet device nodes, we have to match the bus as SBUS.
Otherwise the address and size cell counts are wrong and we don't
calculate the final physical device resource values correctly at all.
Commit 5280267c1dddb8d413595b87dc406624bb497946 ("sparc: Fix handling
of LANCE and ESP parent nodes in of_device.c") was meant to fix this
problem, but that only influences the inner loop of
build_device_resources(). We need this logic to also kick in at the
beginning of build_device_resources() as well, when we make the first
attempt to determine the device's immediate parent bus type for 'reg'
property element extraction.
Based almost entirely upon a patch by Friedrich Oslage.
Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
get_event_name uses sprintf to fill a buffer declared on the stack. It fills
the buffer 2 bytes at a time. What the code doesn't take into account is that
sprintf(buf, "%02x", data) actually writes 3 bytes. 2 bytes for the data and
then it nul terminates the string. Since we declare buf to be 40 characters
long and then we write 40 bytes of data into buf sprintf is going to write 41
characters. The fix is to leave room in buf for the nul terminator.
Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: James Morris <jmorris@namei.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The problem is that permission checking is skipped if atomic open is
possible, but when exec opens a file, it just opens it O_READONLY which
means EXEC permission will not be checked at that time.
This problem is observed by the following sequence (executed as root):
mount -t nfs4 server:/ /mnt4
echo "ls" >/mnt4/foo
chmod 744 /mnt4/foo
su guest -c "mnt4/foo"
Actually the icom driver is crashing when is being removed because
the driver is kfreeing the adapter structure before calling
pci_release_regions(), which result in the following error:
Rearrange locking of i_mutex on destination and call to
ocfs2_rw_lock() so locks are only held while buffers are copied with
the pipe_to_file() actor, and not while waiting for more data on the
pipe.
Rearrange locking of i_mutex on destination so it's only held while
buffers are copied with the pipe_to_file() actor, and not while
waiting for more data on the pipe.
splice_from_pipe_next() will wait (if necessary) for more buffers to
be added to the pipe. splice_from_pipe_feed() will feed the buffers
to the supplied actor and return when there's no more data available
(or if all of the requested data has been copied).
This is necessary so that implementations can do locking around the
non-waiting splice_from_pipe_feed().
This patch should not cause any change in behavior.
The MPC5200 PSC device is wired up to a dedicated interrupt line
which is never shared. This patch removes the IRQF_SHARED flag
from the request_irq() call which eliminates the "IRQF_DISABLED
is not guaranteed on shared IRQs" warning message from the console
output.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes an invalid pointer access in case the receive queue
holds no pointer to the next skb when the queue is empty.
Signed-off-by: Hannes Hering <hering2@de.ibm.com> Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After 2f9092e1020246168b1309b35e085ecd7ff9ff72 "Fix i_mutex vs. readdir
handling in nfsd" (and 14f7dd63 "Copy XFS readdir hack into nfsd code"),
an entry may be removed between the first mutex_unlock and the second
mutex_lock. In this case, lookup_one_len() will return a negative
dentry. Check for this case to avoid a NULL dereference.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Reviewed-by: J. R. Okajima <hooanon05@yahoo.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a size check WRT the manual pages. This was inadvertently broken by
commit 9fe5ad9c8cef9ad5873d8ee55d1cf00d9b607df0 ("flag parameters
add-on: remove epoll_create size param").
cifs: fix unicode string area word alignment in session setup
The handling of unicode string area alignment is wrong.
decode_unicode_ssetup improperly assumes that it will always be preceded
by a pad byte. This isn't the case if the string area is already
word-aligned.
This problem, combined with the bad buffer sizing for the serverDomain
string can cause memory corruption. The bad alignment can make it so
that the alignment of the characters is off. This can make them
translate to characters that are greater than 2 bytes each. If this
happens we can overflow the allocation.
Fix this by fixing the alignment in CIFS_SessSetup instead so we can
verify it against the head of the response. Also, clean up the
workaround for improperly terminated strings by checking for a
odd-length unicode buffers and then forcibly terminating them.
Finally, resize the buffer for serverDomain. Now that we've fixed
the alignment, it's probably fine, but a malicious server could
overflow it.
A better solution for handling these strings is still needed, but
this should be a suitable bandaid.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Cc: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Acked-by: Steve French <sfrench@us.ibm.com> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cifs: Rename cifs_strncpy_to_host and fix buffer size
There is a possibility for the path_name and node_name buffers to
overflow if they contain charcters that are >2 bytes in the local
charset. Resize the buffer allocation so to avoid this possibility.
Also, as pointed out by Jeff Layton, it would be appropriate to
rename the function to cifs_strlcpy_to_host to reflect the fact
that the copied string is always NULL terminated.
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cifs: Increase size of tmp_buf in cifs_readdir to avoid potential overflows
Increase size of tmp_buf to possible maximum to avoid potential
overflows. Also moved UNICODE_NAME_MAX definition so that it can be used
elsewhere.
Pointed-out-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cifs: fix buffer size for tcon->nativeFileSystem field
The buffer for this was resized recently to fix a bug. It's still
possible however that a malicious server could overflow this field
by sending characters in it that are >2 bytes in the local charset.
Double the size of the buffer to account for this possibility.
Also get rid of some really strange and seemingly pointless NULL
termination. It's NULL terminating the string in the source buffer,
but by the time that happens, we've already copied the string.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Cc: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit c2ec175c39f62949438354f603f4aa170846aabb ("mm: page_mkwrite
change prototype to match fault") exposed a bug in the NFS
implementation of page_mkwrite. We should be returning 0 on success...
Change page_mkwrite to allow implementations to return with the page
locked, and also change it's callers (in page fault paths) to hold the
lock until the page is marked dirty. This allows the filesystem to have
full control of page dirtying events coming from the VM.
Rather than simply hold the page locked over the page_mkwrite call, we
call page_mkwrite with the page unlocked and allow callers to return with
it locked, so filesystems can avoid LOR conditions with page lock.
The problem with the current scheme is this: a filesystem that wants to
associate some metadata with a page as long as the page is dirty, will
perform this manipulation in its ->page_mkwrite. It currently then must
return with the page unlocked and may not hold any other locks (according
to existing page_mkwrite convention).
In this window, the VM could write out the page, clearing page-dirty. The
filesystem has no good way to detect that a dirty pte is about to be
attached, so it will happily write out the page, at which point, the
filesystem may manipulate the metadata to reflect that the page is no
longer dirty.
It is not always possible to perform the required metadata manipulation in
->set_page_dirty, because that function cannot block or fail. The
filesystem may need to allocate some data structure, for example.
And the VM cannot mark the pte dirty before page_mkwrite, because
page_mkwrite is allowed to fail, so we must not allow any window where the
page could be written to if page_mkwrite does fail.
This solution of holding the page locked over the 3 critical operations
(page_mkwrite, setting the pte dirty, and finally setting the page dirty)
closes out races nicely, preventing page cleaning for writeout being
initiated in that window. This provides the filesystem with a strong
synchronisation against the VM here.
- Sage needs this race closed for ceph filesystem.
- Trond for NFS (http://bugzilla.kernel.org/show_bug.cgi?id=12913).
- I need it for fsblock.
- I suspect other filesystems may need it too (eg. btrfs).
- I have converted buffer.c to the new locking. Even simple block allocation
under dirty pages might be susceptible to i_size changing under partial page
at the end of file (we also have a buffer.c-side problem here, but it cannot
be fixed properly without this patch).
- Other filesystems (eg. NFS, maybe btrfs) will need to change their
page_mkwrite functions themselves.
[ This also moves page_mkwrite another step closer to fault, which should
eventually allow page_mkwrite to be moved into ->fault, and thus avoiding a
filesystem calldown and page lock/unlock cycle in __do_fault. ]
[akpm@linux-foundation.org: fix derefs of NULL ->mapping] Cc: Sage Weil <sage@newdream.net> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fs: fix page_mkwrite error cases in core code and btrfs
page_mkwrite is called with neither the page lock nor the ptl held. This
means a page can be concurrently truncated or invalidated out from
underneath it. Callers are supposed to prevent truncate races themselves,
however previously the only thing they can do in case they hit one is to
raise a SIGBUS. A sigbus is wrong for the case that the page has been
invalidated or truncated within i_size (eg. hole punched). Callers may
also have to perform memory allocations in this path, where again, SIGBUS
would be wrong.
The previous patch ("mm: page_mkwrite change prototype to match fault")
made it possible to properly specify errors. Convert the generic buffer.c
code and btrfs to return sane error values (in the case of page removed
from pagecache, VM_FAULT_NOPAGE will cause the fault handler to exit
without doing anything, and the fault will be retried properly).
This fixes core code, and converts btrfs as a template/example. All other
filesystems defining their own page_mkwrite should be fixed in a similar
manner.
Acked-by: Chris Mason <chris.mason@oracle.com> Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the page_mkwrite prototype to take a struct vm_fault, and return
VM_FAULT_xxx flags. There should be no functional change.
This makes it possible to return much more detailed error information to
the VM (and also can provide more information eg. virtual_address to the
driver, which might be important in some special cases).
This is required for a subsequent fix. And will also make it easier to
merge page_mkwrite() with fault() in future.
Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Chris Mason <chris.mason@oracle.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Cc: Miklos Szeredi <miklos@szeredi.hu> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Joel Becker <joel.becker@oracle.com> Cc: Artem Bityutskiy <dedekind@infradead.org> Cc: Felix Blyakher <felixb@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, the i2c-algo-pca driver does nothing if the chip enters state
0x30 (Data byte in I2CDAT has been transmitted; NOT ACK has been
received). Thus, the i2c bus connected to the controller gets stuck
afterwards.
I have seen this kind of error on a custom board in certain load
situations most probably caused by interference or noise.
A possible reaction is to let the controller generate a STOP condition.
This is documented in the PCA9564 data sheet (2006-09-01) and the same
is done for other NACK states as well.
Further, state 0x38 isn't handled completely, either. Try to do another
START in this case like the data sheet says. As this couldn't be tested,
I've added a comment to try to reset the chip if the START doesn't help
as suggested by Wolfram Sang.
Signed-off-by: Enrik Berkhan <Enrik.Berkhan@ge.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When fetching DDC using i2c algo bit, we were often seeing timeouts
before getting valid EDID on a retry. The VESA spec states 2ms is the
DDC timeout, so when this translates into 1 jiffie and we are close
to the end of the time period, it could return with a timeout less than
2ms.
Change this code to use time_after instead of time_after_eq.
Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The return value of dup2 when oldfd == newfd and the fd isn't valid is
not getting properly sign extended. We end up with 4294967287 instead
of -EBADF.
I've reproduced this on SLE11 (2.6.27.21), openSUSE Factory
(2.6.29-rc5), and Ubuntu 9.04 (2.6.28).
This patch uses a signed int for the error value so it is properly
extended.