Hauke Mehrtens [Mon, 27 Feb 2012 23:56:10 +0000 (00:56 +0100)]
bcma: add support for sprom not found on the device
On SoCs the sprom is stored in the nvram in a special partition on the
flash chip. The nvram contains the sprom for the main bus, but
sometimes also for a pci devices using bcma. This patch makes it
possible for the arch code to register a function to fetch the needed
sprom from the nvram and provide it to the bcma code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Mon, 27 Feb 2012 23:56:08 +0000 (00:56 +0100)]
ssb: add some missing sprom attributes
This patch extends the sprom struct to contain all sprom attributes
found in sprom version 1 to 9. This was done accordingly to the open
source part of the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Mon, 27 Feb 2012 23:56:06 +0000 (00:56 +0100)]
ssb: fix per path sprom vars
On sprom version 4 and 5 there are 4 values for pa_2g, pa_5gl, pa_5g
and pa_5gh, for sprom version 8 and 9 there are only 3. Make the per
path sprom store also work for older sprom versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Mon, 27 Feb 2012 23:56:05 +0000 (00:56 +0100)]
ssb: remove 5GHz antenna gain from sprom
There is no 2.4 GHz or 5GHz antenna gain stored in sprom. The sprom
just stores the gain values for antenna 1 and 2 or 1 to 4 for more
recent sprom versions. On old devices antenna 2 was used for 5 GHz wifi.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Mon, 27 Feb 2012 23:56:04 +0000 (00:56 +0100)]
ssb: sprom fix some sizes / signedness
Some parts of the sprom struct are bigger than needed.
The leddc and maxpwr values are just 8 bit long and not 16.
rxpo2g and rxpo5g are signed
I got these information for the open source part of the Broadcom SDK
covering sprom version 1 to 9. rxpo2g contained a negative number on my
bcm5354 based device, this cased an error and Broadcom SDK says this is
signed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 27 Feb 2012 18:58:41 +0000 (19:58 +0100)]
ath9k_hw: enable interrupts for beacon tx completion events
Not doing so could cause the tx status queue to overflow during longer
periods of time without non-beacon tx. These events are also required
for proper drv_tx_last_beacon handling.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 27 Feb 2012 18:58:40 +0000 (19:58 +0100)]
ath9k: do not call ath9k_hw_txprocdesc on AR9003 outside of the tx tasklet
Since AR9003 uses a global tx status queue, processing tx status outside of
the regular tx tasklet is dangerous and messes up hardware/software
synchronization of tx status events.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 27 Feb 2012 18:58:39 +0000 (19:58 +0100)]
Revert "ath9k_hw: Fix false tx hung detection in AR9003 chips"
The approach of this change is flawed, as it triggers tx status processing
from more callsites, yet the chips only have one global tx status queue.
Subsequent patches will properly fix the issue that this one tried to address.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Sat, 25 Feb 2012 05:36:05 +0000 (21:36 -0800)]
mwifiex: handle auto authentication mode correctly
When authentication type is configured to NL80211_AUTHTYPE_AUTOMATIC,
driver tries to connect using open mode. The association is failed
if AP is configured in shared mode.
This patch adds code to try association using shared mode as well if
open mode association fails.
Now since we returned exact error code in association response handler
(instead of -1), corresponding changes are done in
mwifiex_process_cmdresp().
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 29 Feb 2012 20:08:33 +0000 (15:08 -0500)]
carl9170: fix breakage from "mac80211: handle non-bufferable MMPDUs correctly"
That commit intended for 3.4 renamed IEEE80211_TX_CTL_POLL_RESPONSE as
IEEE80211_TX_CTL_NO_PS_BUFFER. Meanwhile, "carl9170: fix frame delivery
if sta is in powersave mode" added a reference to
IEEE80211_TX_CTL_POLL_RESPONSE in the fixes stream for 3.3. This simple
patch fixes that merge boo-boo.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zefir Kurtisi [Mon, 27 Feb 2012 11:52:06 +0000 (12:52 +0100)]
ath9k: decouple RX error checking for DFS
Previous RX error checking was done exclusive-or for different error
types and caused DFS pulse events to be dropped when other error
flags (e.g. CRC) were set simultaneously.
This patch decouples PHY error processing from other types and ensures
that all pulses detected by HW are accounted by the pattern detector.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Greg Dietsche [Mon, 27 Feb 2012 18:25:32 +0000 (12:25 -0600)]
iwlegacy: remove enum iw_calib and related code
Remove the enum il_calib. It defined one identifier: IL_CALIB_MAX.
Remove the function il4965_calib_free_results. It was doing nothing
because IL_CALIB_MAX is zero. Next, remove calib_results from the
il_priv structure and also remove the associated return
type/struct il_calib_result.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Greg Dietsche [Mon, 27 Feb 2012 18:25:31 +0000 (12:25 -0600)]
iwlegacy: Kconfig: Change Debug Option to be more clear
Since the menuconfig system doesn't indent the debug options
for the 3945 /4965, add some text to make it clear which
debug options are being configured.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 27 Feb 2012 11:18:30 +0000 (12:18 +0100)]
mac80211: handle non-bufferable MMPDUs correctly
This renames the IEEE80211_TX_CTL_POLL_RESPONSE
TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also
uses it for non-bufferable MMPDUs (all MMPDUs but
deauth, disassoc and action frames.)
Previously, mac80211 would let the MMPDU through
but not set the flag so drivers supporting some
hardware aids for avoiding the PS races would
then reject the frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of defining an 'enum', we can simply use 'u8' flag for WEP
status. Rename 'wep_status' to 'wep_enabled' to match with
'wpa_enabled' and 'wpa2_enabled'.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Sat, 25 Feb 2012 05:35:36 +0000 (21:35 -0800)]
mwifiex: remove redundant scan operation
It should have been removed by commit "mwifiex: use cfg80211 dynamic
scan..." (7c6fa2a843..) after adding code to avoid an extra scan
during association because scan entries are valid for 15 seconds in
cfg80211 stack.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 24 Feb 2012 12:50:54 +0000 (13:50 +0100)]
mac80211: make deauth/disassoc sequence more natural
The association sequence looks (roughly) like
this now:
* set BSSID
* set station to EXIST state
* send auth
* set station to AUTH state
* send assoc
* set station to ASSOC state
* set BSS info to associated
In contrast, the deauth/disassoc sequence is
the other way around:
* clear BSSID/BSS info state
* remove station
* send deauth/disassoc
(in some cases the last two steps are reversed.)
This patch encodes the entire sequence in the
ieee80211_set_disassoc() function and changes
it to be like this, for good measure with an
explicit flush:
* send deauth/disassoc
* flush
* remove station
* clear BSSID/BSS info state
At least iwlwifi gets confused with the other
sequence in P2P mode and complains that it
wasn't able to flush the queues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ieee80211_set_disassoc() is called with the
tx argument set to true, it will send DelBA out
to the peer. This isn't useful or necessary in a
few cases where we do it today, those being when
we lost the connection or when the supplicant
explicitly asked us to not tell the AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 24 Feb 2012 12:50:52 +0000 (13:50 +0100)]
mac80211: dont call cfg80211 from ieee80211_send_deauth_disassoc
Instead of calling cfg80211 in ieee80211_send_deauth_disassoc()
pass out the frame and call it from the caller. That saves the
SKB allocation if we don't actually want to send the frame and
enables us to make the ordering smarter in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 24 Feb 2012 12:50:51 +0000 (13:50 +0100)]
cfg80211: remove cookies from callbacks
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
A second ifconfig wlan0 up brings the interface up without problems.
After a bit more debugging, the call trace is the following:
[10241.028130] zd1211rw 1-3:1.0: zd_chip_lock_phy_regs: error
ioread32(CR_REG1): -110
[10241.028140] zd1211rw 1-3:1.0: zd_switch_radio_on: failed to lock PHY regs
[10241.028148] zd1211rw 1-3:1.0: zd_op_start: failed to set radio on
Adding a 10 milliseconds delay between the call to set_mc_hash() and
zd_chip_switch_radio_on() allows successful interface bringups in all
cases and matches what the vendor driver did.
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Sat, 25 Feb 2012 05:35:35 +0000 (21:35 -0800)]
mwifiex: reset encryption mode flag before association
Recent commit
"mwifiex: clear previous security setting during association"
fixes association failure problems observed in some corner cases
by clearing previous security setting before each association.
We should reset encryption mode flag as well. This patch takes care
of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: fix frame delivery if sta is in powersave mode
Nicolas Cavallari discovered that carl9170 has some
serious problems delivering data to sleeping stations.
It turns out that the driver was not honoring two
important flags (IEEE80211_TX_CTL_POLL_RESPONSE and
IEEE80211_TX_CTL_CLEAR_PS_FILT) which are set on
frames that should be sent although the receiving
station is still in powersave mode.
Cc: stable <stable@vger.kernel.org> Reported-by: Nicolas Cavallari <Nicolas.Cavallari@lri.fr> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: Fix memory accounting when sta is in power-save mode.
On Access Point mode, when transmitting a packet, if the destination
station is in powersave mode, we abort transmitting the packet to the
device queue, but we do not reclaim the allocated memory. Given enough
packets, we can go in a state where there is no packet on the device
queue, but we think the device has no memory left, so no packet gets
transmitted, connections breaks and the AP stops working.
This undo the allocation done in the TX path when the station is in
power-save mode.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This handler allows the transport layer to free an skb from the
op_mode. This can happen when the driver is stopped while Tx
packets are pending in the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Define the op_mode as an interface with its ops. All the functions
of the op_mode are "private", but its ops is made public in
iwl-op-mode.h.
The drv object starts the op_mode by using the start function in the
public ops.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlwifi: rename iwl_remove to iwl_op_mode_dvm_stop
iwl_remove stops the wifi flows, so rename.
Moreover, we can possibly stop the wifi flows even if the driver
is statically compiled in the kernel, so remove the __devexit pragma.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Fetch the fw and spawn the op_mode. The op_mode that we need
to fetch is determined from the fw file.
Since the fw is fetched very early in the init flow, we can
determine what op_mode to spawn.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Tue, 21 Feb 2012 16:31:06 +0000 (18:31 +0200)]
iwlwifi: move uCode flags handling to op_mode
The uCode flags modification is op_mode dependent
since the P2P config is an op-mode config.
This also fixes P2P enabling: due to the uCode
loading code shuffle moving the SKU check before
the EEPROM was read it was always false and would
always disable PAN/P2P.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlwifi: move content of iwl_probe to post fetch_fw
This will allow to have different behavior depending on the fw.
Different fw APIs require completely different implementation
of the mac80211 APIs. Each of these implementations is called an
op_mode.
The current op_mode is called DVM which states for dual virtual MAC.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlwifi: parse_tlv functions set the fw_version string
struct iwl_fw contains a string that describe the fw. This string
is now set by the iwl_parse_*_firmware.
This string is later used to update the cfg80211 data.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Jakub Kicinski [Wed, 22 Feb 2012 20:58:58 +0000 (21:58 +0100)]
rt2800pci: Fix 'Error - MCU request failed' during initialization
Bring MCU operations during device initialization to sync
with legacy driver.
This should fix following error:
phy0 -> rt2800pci_mcu_status: Error - MCU request failed,
no response from hardware
Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jakub Kicinski [Wed, 22 Feb 2012 20:58:57 +0000 (21:58 +0100)]
rt2800: Add documentation on MCU requests
Add documentation on MCU communication, some of known commands and
their arguments. Supplement command ids.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Danny Kukawka [Wed, 15 Feb 2012 17:55:16 +0000 (18:55 +0100)]
iwlwifi: iwl-agn.h included twice
drivers/net/wireless/iwlwifi/iwl-core.c included 'iwl-agn.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 25 Feb 2012 20:40:46 +0000 (21:40 +0100)]
mac80211: fix sta_info_flush() return value
The comment for sta_info_flush() states
"Returns the number of removed STA entries"
but that isn't actually true. Consequently,
the warning when a station is still around
on interface removal can never trigger and
this delayed finding the timer issue the
previous patch fixed. Fix the return value
here to make that warning useful again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 25 Feb 2012 20:48:08 +0000 (21:48 +0100)]
mac80211: fix auth/assoc data & timer leak
When removing an interface while it is in the
process of authenticating or associating, we
leak the auth_data or assoc_data, and leave
the timer pending. The timer then crashes the
system when it fires as its data is gone.
Fix this by explicitly deleting all the data
when the interface is removed. This uncovered
another bug -- this problem should have been
detected by the sta_info_flush() warning but
that function doesn't ever return non-zero,
I'll fix that in a separate patch.
Reported-by: Hieu Nguyen <hieux.c.nguyen@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Fri, 24 Feb 2012 06:22:51 +0000 (07:22 +0100)]
brcm80211: fmac: use correct firmware filename
Also don't use so generic BRCMF_USB_FW_NAME as we may need different
firmwares in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Fri, 24 Feb 2012 06:22:27 +0000 (09:22 +0300)]
brcm80211: fmac: fix a couple checking after dereference bugs
There were two dereferencing before checking for NULL static checker
complaints in this new file. The list cursor is never NULL so that
check can be removed. I moved the other dereference after the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jakub Kicinski [Thu, 23 Feb 2012 01:17:48 +0000 (02:17 +0100)]
mac80211: use proper sub_if_data on suspend path
Use interface data from sta instead of invalid pointer
to list head in calls to drv_sta_state.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 22 Feb 2012 07:10:09 +0000 (12:40 +0530)]
ath9k: Cleanup MCI init/deinit routines
This patch simplifies the buffer allocation functions
for MCI and removes unneeded memset calls. Also, a couple
of unused variables are removed and a memory leak in DMA
allocation is fixed.
Johannes Berg [Mon, 20 Feb 2012 13:19:58 +0000 (14:19 +0100)]
mac80211: fix associated vs. idle race
Eliad reports that if a scan finishes in the
middle of processing associated (however it
happens), the interface can go idle. This is
because we set assoc_data to NULL before we
set associated. Change the order so any idle
check will find either one of them.
Doing this requires duplicating the TX sync
processing, but I already have a patch to
delete that completely and will submit that
as soon as my driver changes to no longer
require it are submitted.
Reported-by: Eliad Peller <eliad@wizery.com> Tested-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 20 Feb 2012 10:38:41 +0000 (11:38 +0100)]
mac80211: clean up asm/unaligned.h inclusion
Some files implicitly get this via mesh.h
which itself doesn't need it, so move the
inclusion into the right files. Some other
files don't need it at all but include it,
so remove it from there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John Li [Fri, 17 Feb 2012 09:33:06 +0000 (17:33 +0800)]
rt2x00:Add RT5372 chipset support
Signed-off-by: John Li <chen-yang.li@mediatek.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log