drm/tegra: Start connectors with correct DPMS mode
A connector's DPMS mode isn't initialized by default, therefore using a
default of 0 (DRM_MODE_DPMS_ON). This can cause problems in that the DRM
core won't explicitly turn on a connector because it thinks that it is
already on.
Thierry Reding [Fri, 30 Aug 2013 13:10:14 +0000 (15:10 +0200)]
drm/panel: Add simple panel support
Add a driver for simple panels. Such panels can have a regulator that
provides the supply voltage and a separate GPIO to enable the panel.
Optionally the panels can have a backlight associated with them so it
can be enabled or disabled according to the panel's power management
mode.
Support is added for three panels: An AU Optronics 10.1" WSVGA, a
Chunghwa Picture Tubes 10.1" WXGA and a Panasonic 10.1 WUXGA TFT LCD
panel.
Thierry Reding [Fri, 30 Aug 2013 11:36:43 +0000 (13:36 +0200)]
drm: Add panel support
Add a very simple framework to register and lookup panels. Panel drivers
can initialize a DRM panel and register it with the framework, allowing
them to be retrieved and used by display drivers. Currently only support
for DPMS and obtaining panel modes is provided. However it should be
sufficient to enable a large number of panels. The framework should also
be easily extensible to support more sophisticated kinds of panels such
as DSI.
The framework hasn't been tied into the DRM core, even though it should
be easily possible to do so if that's what we want. In the current
implementation, display drivers can simple make use of it to retrieve a
panel, obtain its modes and control its DPMS mode.
Note that this is currently only tested on systems that boot from a
device tree. No glue code has been written yet for systems that use
platform data, but it should be easy to add.
Mikko Perttunen [Wed, 28 Aug 2013 15:48:39 +0000 (18:48 +0300)]
drm/tegra: hdmi: Enable VDD earlier for hotplug/DDC
The VDD regulator used to be enabled only at tegra_output_hdmi_enable,
which is called after a sink is detected. However, the HDMI hotplug pin
works by returning the voltage supplied by the VDD pin, so this meant
that the hotplug pin was never asserted and the sink was not detected
unless the VDD regulator was set to be always on.
This patch moves the enable to the tegra_hdmi_init() function to make
sure the regulator will get enabled and therefore ensure proper hotplug
detection.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Wed, 16 Oct 2013 17:51:22 +0000 (19:51 +0200)]
drm/tegra: hdmi: Fix build warnings
These seem to show up when building for architectures other than ARM,
which I guess will never happen. The reason why the kbuild test bot ran
into these was a missing dependency which has hence been fixed. Still it
doesn't hurt to fix them anyway.
Reported-by: kbuild test bot <fengguang.wu@intel.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Mikko Perttunen [Wed, 28 Aug 2013 15:48:38 +0000 (18:48 +0300)]
drm/tegra: hdmi: Detect DVI-only displays
Use EDID data to determine whether the display supports HDMI or DVI
only. The HDMI output used to assume to be connected to HDMI displays,
but that broke support for DVI displays that don't understand the
interspersed audio/other data.
To be on the safe side, default to DVI if no EDID data is available.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
[treding@nvidia.com: move detection to separate function] Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Mon, 14 Oct 2013 07:43:05 +0000 (09:43 +0200)]
drm/tegra: hdmi: Parameterize based on compatible property
Use a structure to parameterize the code to handle differences between
the HDMI hardware on various SoC generations. This removes the need to
clutter the code with checks for individual compatible values.
drm/tegra: hdmi: Rename tegra{2,3} to tegra{20,30}
Everything related to Tegra uses Tegra20 and Tegra30 instead of Tegra2
and Tegra3, respectively. Rename the TMDS arrays in the HDMI driver for
consistency.
Thierry Reding [Mon, 14 Oct 2013 12:26:42 +0000 (14:26 +0200)]
drm/tegra: Allocate resources at probe time
Since the .init() and .exit() functions are executed whenever the DRM
driver is loaded or unloaded, care must be taken not to use them for
resource allocation. Otherwise deferred probing cannot be used, since
the .init() and .exit() are not run at probe time. Similarly the code
that frees resources must be run at .remove() time. If it is run from
the .exit() function, it can release resources multiple times.
To handle this more consistently, rename the tegra_output_parse_dt()
function to tegra_output_probe() and introduce tegra_output_remove()
which can be used to free output-related resources.
Thierry Reding [Mon, 14 Oct 2013 12:06:02 +0000 (14:06 +0200)]
drm/tegra: Properly cleanup and zero out resources
When the DRM driver is unloaded, all the associated resources must be
cleaned up and zeroed out. This is necessary because of the architecture
of the Tegra DRM driver, where not all subdrivers are unloaded along
with the DRM driver. Therefore device-managed managed won't be freed and
memory cannot be assumed to have been cleared (because it hasn't been
reallocated using kzalloc()) by the time the DRM driver is reloaded. It
is therefore necessary to zero out the structures to prevent strange
errors (such as slab corruptions) from occurring.
Thierry Reding [Mon, 14 Oct 2013 12:43:22 +0000 (14:43 +0200)]
drm/tegra: Move subdevice infrastructure to host1x
The Tegra DRM driver currently uses some infrastructure to defer the DRM
core initialization until all required devices have registered. The same
infrastructure can potentially be used by any other driver that requires
more than a single sub-device of the host1x module.
Make the infrastructure more generic and keep only the DRM specific code
in the DRM part of the driver. Eventually this will make it easy to move
the DRM driver part back to the DRM subsystem.
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v3:
- use newly introduced drm_dev_alloc(), drm_dev_register() and
drm_dev_free()
- fix module unload/reload of both host1x and DRM drivers
This structure derives from host1x_client. DRM-specific fields are moved
from host1x_client to this structure, so that host1x_client can remain
agnostic of DRM.
Rework the address table code for the host1x firewall. The previous
implementation allocated a bitfield but didn't check for a valid pointer
so it could potentially crash. Instead, embed a static bitmap within the
gr2d structure to avoid the allocation and use the Linux bitmap API to
reduce code complexity.
Don't annotate the driver's .remove() function __exit. Even if built in
the driver can be unloaded via sysfs, so .remove() needs to stick around
after initialization. Also remove the explicit initialization of the
driver's .owner field to THIS_MODULE because that's now handled by the
driver core.
Furthermore make an error message more consistent with other subdrivers,
index the syncpts array for better readability, remove a gratuituous
newline and reorder some variable declarations to make the code easier
to read.
The device can be unbound from the driver via sysfs, so regardless of
whether the driver is builtin or a module, its .remove() function needs
to stick around.
drm/tegra: Rename host1x_drm_context to tegra_drm_context
The structure represents a context associated with a particular process
that has opened the Tegra DRM device and requested a channel. This is a
very DRM-specific notion and has nothing to do with host1x. Rename the
structure to more clearly mark the boundaries between the two.
drm/tegra: Rename host1x_drm_file to tegra_drm_file
This structure extends drm_file with Tegra DRM specific fields and has
nothing to do with host1x. Rename the structure to more clearly mark the
boundaries between host1x and Tegra DRM.
While at it, move the structure definition out of the header. It's never
used outside of the drm.c source file, so it can be defined within that.
Thierry Reding [Wed, 2 Oct 2013 13:50:06 +0000 (15:50 +0200)]
drm: Track the proper DPMS mode of connectors
When userspace removes the active framebuffer using DRM_IOCTL_MODE_RMFB,
or explicitly disables the CRTC (by calling drmModeSetCrtc(..., NULL)
for example), a NULL framebuffer will be passed to the .set_config()
implementation of a CRTC. The drm_crtc_helper_set_config() helper will
decide to disable a CRTC when that happens.
To do so, it calls drm_crtc_helper_disable(), which in turn will iterate
over all encoders and decouple them from their connectors and finally
call drm_helper_disable_unused_functions() to clean up and call the
.disable() or .dpms() implementation for each encoder. However, at no
point during this sequence does it track the DPMS mode of a connector,
so it will usually remain on after this.
When a connector is enabled again, drm_helper_connector_dpms() will not
notice that the DPMS mode actually changed and won't do anything, which
causes the connector to stay disabled indefinitely.
To prevent this from happening, explicitly set the connector's DPMS mode
to off when the CRTC is disabled. That way it reflects the correct state
and can be enabled again.
This solves an issue observed when terminating an X server running on
the xf86-video-modesetting driver. Without this patch, the connector
would not be enabled properly and the screen would stay dark.
Acked-by: David Airlie <airlied@linux.ie> Signed-off-by: Thierry Reding <treding@nvidia.com>
Dave Airlie [Tue, 15 Oct 2013 08:04:08 +0000 (18:04 +1000)]
Merge branch 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel into drm-next
New feature pile for 3.12! Highlights:
- Stereo/3d support for hdmi from Damien, both the drm core bits and
the i915 integration.
- Manual boost/deboost logic for gpu turbo (Chris)
- Fixed up clock readout support for vlv (Chris).
- Tons of little fixes and improvements for vlv in general (Chon Minng
Lee and Jesse Barnes).
- Power well support for the legacy vga plane (Ville).
- DP impromevents from Jani.
- Improvements to the Haswell modeset sequence (Ville+Paulo).
- Haswell DDI improvements, using the VBT for some tuning values and
to check the configuration (Paulo).
- Tons of other small improvements and fixups.
* 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel: (92 commits)
drm/i915: Use adjusted_mode in the fastboot hack to disable pfit
drm/i915: Add a more detailed comment about the set_base() fastboot hack
drm/i915/vlv: Turn off power gate for BIOS-less system.
drm/i915/vlv: reset DPIO on load and resume v2
drm/i915: Simplify PSR debugfs
drm/i915: Tweak RPS thresholds to more aggressively downclock
drm/i915: Boost RPS frequency for CPU stalls
drm/i915: Fix __wait_seqno to use true infinite timeouts
drm/i915: Add some missing steps to i915_driver_load error path
drm/i915: Clean up the ring scaling calculations
drm/i915: Don't populate pipe_src_{w,h} multiple times
drm/i915: implement the Haswell mode set sequence workaround
drm/i915: Disable/enable planes as the first/last thing during modeset on HSW
i915/vlv: untangle integrated clock source handling v4
drm/i915: fix typo s/PatherPoint/PantherPoint/
drm/i915: Make intel_resume_power_well() static
drm/i915: destroy connector sysfs files earlier
drm/i915/dp: do not write DP_TRAINING_PATTERN_SET all the time
drm/i915/dp: retry i2c-over-aux seven times on AUX DEFER
drm/i915/vlv: reduce GT FIFO error info to a debug message
...
Daniel Vetter [Thu, 10 Oct 2013 10:44:43 +0000 (12:44 +0200)]
Merge remote-tracking branch 'airlied/drm-next' into drm-intel-next
The conflict in intel_drv.h tripped me up a bit since a patch in dinq
moves all the functions around, but another one in drm-next removes a
single function. So I'ev figured backing this into a backmerge would
be good.
i915_dma.c is just adjacent lines changed, nothing nefarious there.
Jani Nikula [Fri, 4 Oct 2013 12:08:10 +0000 (15:08 +0300)]
drm/i915/dp: get rid of intel_dp->link_configuration
It's not really needed, rather just adds another place to hold
intermediate values that could go wrong, and it's not clear that the
training pattern set or training lane set should be written at this
point at all.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jani Nikula [Fri, 4 Oct 2013 12:08:09 +0000 (15:08 +0300)]
drm/radeon/dp: use drm_dp_enhanced_frame_cap()
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jani Nikula [Fri, 4 Oct 2013 12:08:08 +0000 (15:08 +0300)]
drm/dp: add helper for checking DP_ENHANCED_FRAME_CAP in DPCD
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Fri, 4 Oct 2013 11:53:40 +0000 (14:53 +0300)]
drm: Remove pci_vendor and pci_device from struct drm_device
We can get the PCI vendor and device IDs via dev->pdev. So we can drop
the duplicated information.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Fri, 4 Oct 2013 11:53:39 +0000 (14:53 +0300)]
drm: Kill ctx_count from struct drm_device
The only user of ctx_count is the via driver, and we can replace that
use with list_is_singular().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Fri, 4 Oct 2013 11:53:38 +0000 (14:53 +0300)]
drm: Kill unused stuff from struct drm_device
'map_count' and 'work' are never used. Kill them both.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Fri, 4 Oct 2013 11:53:37 +0000 (14:53 +0300)]
drm: Make irq_enabled bool
irq_enabled is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Fri, 4 Oct 2013 11:53:36 +0000 (14:53 +0300)]
drm: Collect per-crtc vblank stuff to a struct
drm_vblank_init() is too ugly. Make it a bit easier on the eye by
collecting all the per-crtc vblank counters, timestamps etc. to
a structure and just allocate an array of those.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Fri, 4 Oct 2013 11:53:35 +0000 (14:53 +0300)]
drm: Make vblank_enabled bool
vblank_enabled is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Fri, 4 Oct 2013 11:53:34 +0000 (14:53 +0300)]
drm: Make vblank_inmodeset unsigned
vblank_inmodeset is a bitmask, with only two bits mind you, but better
make it unsigned anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Fri, 4 Oct 2013 11:53:33 +0000 (14:53 +0300)]
drm: Make vblank_disable_allowed bool
vblank_disable_allowed is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Chris Wilson [Wed, 2 Oct 2013 10:12:53 +0000 (11:12 +0100)]
drm: Try loading builtin EDIDs first
If the firmware is not builtin and userspace is not yet running, we can
stall the boot process for a minute whilst the firmware loader times
out. This is contrary to expectations of providing a builtin EDID!
In the process, we can rearrange the code to make the error handling
more resilient and prevent gcc warning about unitialised variables along
the error paths.
v2: Load builtins first, fix gcc second (Jani) and cosmetics (Ville).
v3: Verify that we do not read beyond the end of the fwdata (Ville)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
David Herrmann [Wed, 2 Oct 2013 09:23:38 +0000 (11:23 +0200)]
drm: move device unregistration into drm_dev_unregister()
Analog to drm_dev_register(), we now provide drm_dev_unregister() which
does the reverse. drm_dev_put() is still in place and combines the calls
to drm_dev_unregister() and drm_dev_free() so buses don't have to change.
*_get() and *_put() are used for reference-counting in the kernel.
However, drm_dev_put() definitely does not do any kind of ref-counting.
Hence, use the more appropriate *_register(), *_unregister(), *_alloc()
and *_free() names.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
David Herrmann [Wed, 2 Oct 2013 09:23:37 +0000 (11:23 +0200)]
drm: introduce drm_dev_free() to fix error paths
The error paths in DRM bus drivers currently leak memory as they don't
correctly revert drm_dev_alloc(). Introduce drm_dev_free() to free DRM
devices which haven't been registered, yet.
We must be careful not to introduce any side-effects with cleanups done in
drm_dev_free(). drm_ht_remove(), drm_ctxbitmap_cleanup() and
drm_gem_destroy() are all fine in that regard.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
David Herrmann [Wed, 2 Oct 2013 09:23:36 +0000 (11:23 +0200)]
drm: move drm_lastclose() to drm_fops.c
Try to keep all functions that handle DRM file_operations in drm_fops.c
so internal helpers can be marked static later.
This makes the split between the 3 core files more obvious:
- drm_stub.c: DRM device allocation/destruction and management
- drm_fops.c: DRM file_operations (except for ioctl)
- drm_drv.c: Global DRM init + ioctl handling
Well, ioctl handling is still spread throughout hundreds of source files,
but at least the others are clearly defined this way.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
David Herrmann [Wed, 2 Oct 2013 09:23:35 +0000 (11:23 +0200)]
drm: merge device setup into drm_dev_register()
All bus drivers do device setup themselves. This requires us to adjust all
of them if we introduce new core features. Thus, merge all these into a
uniform drm_dev_register() helper.
Note that this removes the drm_lastclose() error path for AGP as it is
horribly broken. Moreover, no bus driver called this in any other error
path either. Instead, we use the recently introduced AGP cleanup helpers.
We also keep a DRIVER_MODESET condition around pci_set_drvdata() to keep
semantics.
[airlied: keep passing flags through so drivers don't oops on load]
Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
David Herrmann [Wed, 2 Oct 2013 09:23:34 +0000 (11:23 +0200)]
drm: add drm_dev_alloc() helper
Instead of managing device allocation+initialization in each bus-driver,
we should do that in a central place. drm_fill_in_dev() already does most
of it, but also requires the global drm lock for partial AGP device
registration.
Split both apart so we have a clean device initialization/allocation
phase, and a registration phase.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
David Herrmann [Wed, 2 Oct 2013 08:15:18 +0000 (10:15 +0200)]
drm: kill ->gem_init_object() and friends
All drivers embed gem-objects into their own buffer objects. There is no
reason to keep drm_gem_object_alloc(), gem->driver_private and
->gem_init_object() anymore.
New drivers are highly encouraged to do the same. There is no benefit in
allocating gem-objects separately.
Cc: Dave Airlie <airlied@gmail.com> Cc: Alex Deucher <alexdeucher@gmail.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Rob Clark <robdclark@gmail.com> Cc: Inki Dae <inki.dae@samsung.com> Cc: Ben Skeggs <skeggsb@gmail.com> Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
David Herrmann [Wed, 2 Oct 2013 08:15:17 +0000 (10:15 +0200)]
drm/nouveau: embed gem object in nouveau_bo
There is no reason to keep the gem object separately allocated. nouveau is
the last user of gem_obj->driver_private, so if we embed it, we can get
rid of 8bytes per gem-object.
The implementation follows the radeon driver. bo->gem is only valid, iff
the bo was created via the gem helpers _and_ iff the user holds a valid
gem reference. That is, as the gem object holds a reference to the
nouveau_bo. If you use nouveau_ref() to gain a bo reference, you are not
guaranteed to also hold a gem reference. The gem object might get
destroyed after the last user drops the gem-ref via
drm_gem_object_unreference(). Use drm_gem_object_reference() to gain a
gem-reference.
For debugging, we can use bo->gem.filp != NULL to test whether a gem-bo is
valid. However, this shouldn't be used for real functionality to avoid
gem-internal dependencies.
Note that the implementation follows the previous style. However, we no
longer can check for bo->gem != NULL to test for a valid gem object. This
wasn't done before, so we should be safe now.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Acked-by: Maarten Lankhorst <maarten.lankhorst@canonical.com> Reviewed-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Chon Ming Lee [Thu, 3 Oct 2013 15:16:17 +0000 (23:16 +0800)]
drm/i915/vlv: Turn off power gate for BIOS-less system.
During system boot up, by default, the power gate for render, media and
display well still power gated. Normally, BIOS will turn off the power
gate. In the BIOS-less system, the driver need to turn off the power
gate very early during driver load.
v2: Move this to intel_uncore_sanitize to allow it to get call during
resume path. (Daniel)
v3: Remove redundant write 0 to DPIO_CTL, and use DPIO_RESET instead of
just 0x1 (Ville)
Add turn of power gate for display 2d/render well/media well.
v4: Remove toggle cmnreset in intel_uncore_sanitize. Cmnreset should
toggle after CRI clock source has been selected. Jesse DPIO reset patch
which toggle the cmnreset in intel_modeset_init_hw() should handle it.
(Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes [Thu, 3 Oct 2013 18:35:46 +0000 (11:35 -0700)]
drm/i915/vlv: reset DPIO on load and resume v2
DPIO needs to have common reset de-asserted on soft resets like boot and
S3. In some cases, the BIOS will have done this for us, but it should
be safe to do at runtime as well, as long as we do it when the pipes are
otherwise off.
v2: update bit name to match docs better (Ville)
reset after CRI clock select (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=69166 Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Thu, 3 Oct 2013 19:15:06 +0000 (16:15 -0300)]
drm/i915: Simplify PSR debugfs
for igt test case.
v2: remove trailing spaces and fix conflicts
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet:
- make it comipile
- s/IS_HASWELL/HAS_PSR/] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 25 Sep 2013 16:34:57 +0000 (17:34 +0100)]
drm/i915: Tweak RPS thresholds to more aggressively downclock
After applying wait-boost we often find ourselves stuck at higher clocks
than required. The current threshold value requires the GPU to be
continuously and completely idle for 313ms before it is dropped by one
bin. Conversely, we require the GPU to be busy for an average of 90% over
a 84ms period before we upclock. So the current thresholds almost never
downclock the GPU, and respond very slowly to sudden demands for more
power. It is easy to observe that we currently lock into the wrong bin
and both underperform in benchmarks and consume more power than optimal
(just by repeating the task and measuring the different results).
An alternative approach, as discussed in the bspec, is to use a
continuous threshold for upclocking, and an average value for downclocking.
This is good for quickly detecting and reacting to state changes within a
frame, however it fails with the common throttling method of waiting
upon the outstanding frame - at least it is difficult to choose a
threshold that works well at 15,000fps and at 60fps. So continue to use
average busy/idle loads to determine frequency change.
v2: Use 3 power zones to keep frequencies low in steady-state mostly
idle (e.g. scrolling, interactive 2D drawing), and frequencies high
for demanding games. In between those end-states, we use a
fast-reclocking algorithm to converge more quickly on the desired bin.
v3: Bug fixes - make sure we reset adj after switching power zones.
v4: Tune - drop the continuous busy thresholds as it prevents us from
choosing the right frequency for glxgears style swap benchmarks. Instead
the goal is to be able to find the right clocks irrespective of the
wait-boost.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Kenneth Graunke <kenneth@whitecape.org> Cc: Stéphane Marchesin <stephane.marchesin@gmail.com> Cc: Owen Taylor <otaylor@redhat.com> Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com> Cc: "Zhuang, Lena" <lena.zhuang@intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 25 Sep 2013 16:34:56 +0000 (17:34 +0100)]
drm/i915: Boost RPS frequency for CPU stalls
If we encounter a situation where the CPU blocks waiting for results
from the GPU, give the GPU a kick to boost its the frequency.
This should work to reduce user interface stalls and to quickly promote
mesa to high frequencies - but the cost is that our requested frequency
stalls high (as we do not idle for long enough before rc6 to start
reducing frequencies, nor are we aggressive at down clocking an
underused GPU). However, this should be mitigated by rc6 itself powering
off the GPU when idle, and that energy use is dependent upon the workload
of the GPU in addition to its frequency (e.g. the math or sampler
functions only consume power when used). Still, this is likely to
adversely affect light workloads.
In particular, this nearly eliminates the highly noticeable wake-up lag
in animations from idle. For example, expose or workspace transitions.
(However, given the situation where we fail to downclock, our requested
frequency is almost always the maximum, except for Baytrail where we
manually downclock upon idling. This often masks the latency of
upclocking after being idle, so animations are typically smooth - at the
cost of increased power consumption.)
Stéphane raised the concern that this will punish good applications and
reward bad applications - but due to the nature of how mesa performs its
client throttling, I believe all mesa applications will be roughly
equally affected. To address this concern, and to prevent applications
like compositors from permanently boosting the RPS state, we ratelimit the
frequency of the wait-boosts each client recieves.
Unfortunately, this techinique is ineffective with Ironlake - which also
has dynamic render power states and suffers just as dramatically. For
Ironlake, the thermal/power headroom is shared with the CPU through
Intelligent Power Sharing and the intel-ips module. This leaves us with
no GPU boost frequencies available when coming out of idle, and due to
hardware limitations we cannot change the arbitration between the CPU and
GPU quickly enough to be effective.
v2: Limit each client to receiving a single boost for each active period.
Tested by QA to only marginally increase power, and to demonstrably
increase throughput in games. No latency measurements yet.
v3: Cater for front-buffer rendering with manual throttling.
v4: Tidy up.
v5: Sadly the compositor needs frequent boosts as it may never idle, but
due to its picking mechanism (using ReadPixels) may require frequent
waits. Those waits, along with the waits for the vrefresh swap, conspire
to keep the GPU at low frequencies despite the interactive latency. To
overcome this we ditch the one-boost-per-active-period and just ratelimit
the number of wait-boosts each client can receive.
Reported-and-tested-by: Paul Neumann <paul104x@yahoo.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68716 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Kenneth Graunke <kenneth@whitecape.org> Cc: Stéphane Marchesin <stephane.marchesin@gmail.com> Cc: Owen Taylor <otaylor@redhat.com> Cc: "Meng, Mengmeng" <mengmeng.meng@intel.com> Cc: "Zhuang, Lena" <lena.zhuang@intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: No extern for function prototypes in headers.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 25 Sep 2013 16:34:55 +0000 (17:34 +0100)]
drm/i915: Fix __wait_seqno to use true infinite timeouts
When we switched to always using a timeout in conjunction with
wait_seqno, we lost the ability to detect missed interrupts. Since, we
have had issues with interrupts on a number of generations, and they are
required to be delivered in a timely fashion for a smooth UX, it is
important that we do log errors found in the wild and prevent the
display stalling for upwards of 1s every time the seqno interrupt is
missed.
Rather than continue to fix up the timeouts to work around the interface
impedence in wait_event_*(), open code the combination of
wait_event[_interruptible][_timeout], and use the exposed timer to
poll for seqno should we detect a lost interrupt.
v2: In order to satisfy the debug requirement of logging missed
interrupts with the real world requirments of making machines work even
if interrupts are hosed, we revert to polling after detecting a missed
interrupt.
v3: Throw in a debugfs interface to simulate broken hw not reporting
interrupts.
v4: s/EGAIN/EAGAIN/ (Imre)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Don't use the struct typedef in new code.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 23 Sep 2013 20:33:20 +0000 (17:33 -0300)]
drm/i915: Add some missing steps to i915_driver_load error path
We missed adding a few cleanup steps for recent additions.
Reviewer: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Wed, 2 Oct 2013 16:25:02 +0000 (09:25 -0700)]
drm/i915: Clean up the ring scaling calculations
This patch attempts to clean up the ring/IA scaling programming in the
following ways.
1. Fix the comment about the DDR frequency. The math is 266MHz, not
133MHz. Formula was right, docs are wrong.
2. Mask the DCLK register since I don't know how it is defined on future
platforms.
3. use mult_frac instead of magic math.
This helps for future platform enabling.
v2: Actually use the right patch. The v1 was a mix of things, none of
which was right. Note that due to rounding, we actually get different
values (slightly higher) for the effective ring frequency.
v3: Use 1.25 instead of 1.33 as the original code did. (Jesse)
CC: Jesse Barnes <jbarnes@virtuousgeek.org> CC: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 1 Oct 2013 19:52:14 +0000 (22:52 +0300)]
drm/i915: Don't populate pipe_src_{w,h} multiple times
If we ever end up doing the retry loop due to bandwidth constraints, we
would rewrite pipe_src_{w,n} based on adjusted_mode timings. But by that
time the encoder may have already replaced the adjusted_mode with a
fixed panel mode, which would then corrupt pipe_src_{w,h}.
v2: Use requested_mode and slap on a big comment from Daniel
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 20 Sep 2013 19:21:19 +0000 (16:21 -0300)]
drm/i915: implement the Haswell mode set sequence workaround
This workaround is described in the mode set sequence documentation.
When enabling planes for the second pipe, we need to wait for 2
vblanks on the first pipe. This should solve "a flash of screen
corruption if planes are enabled on second/third pipe during the time
that big FIFO mode is exiting". Watermarks are fun :)
v2: Save indentation levels
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 19 Sep 2013 20:00:37 +0000 (17:00 -0300)]
drm/i915: Disable/enable planes as the first/last thing during modeset on HSW
Refactor the plane enabling/disabling into helper functions and move
the calls to happen as the first thing during .crtc_disable, and the
last thing during .crtc_enable.
Those are the two clear points where we are sure that the pipe is
actually running regardless of the encoder type or hardware
generation.
v2: Made by Paulo:
Remove the code touching everything but the Haswell functions. We
need this change on Haswell right now since it fixes a FIFO underrun
that we get on pipe A while we enable pipe B (see the workaround
notes on the Haswell mode set sequence documentation). We can bring
back the code to gens 2-7 later, once they're tested.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The global integrated clock source bit resides in DPLL B on VLV, but we
were treating it as a per-pipe resource. It needs to be set whenever
any PLL is active, so pull setting the bit out of vlv_update_pll and
into vlv_enable_pll. Also add a vlv_disable_pll to prevent disabling it
when pipe B shuts down.
I'm guessing on the references here, I expect this to bite any config
where multiple displays are active or displays are moved from pipe to
pipe.
v2: re-add bits in vlv_update_pll to keep from confusing the state checker
v3: use enum pipe checks (Daniel)
set CRI clock source early (Ville)
consistently set CRI clock source everywhere (Ville)
v4: drop unnecessary setting of bit in vlv enable pll (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=67245
References: https://bugs.freedesktop.org/show_bug.cgi?id=69693 Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/1/PIPE_B/] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 26 Sep 2013 23:05:59 +0000 (20:05 -0300)]
drm/i915: destroy connector sysfs files earlier
For some reason, every single time I try to run module_reload
something tries to read the connector sysfs files. This happens
after we destroy the encoders and before we destroy the connectors, so
when the sysfs read triggers the connector detect() function,
intel_conector->encoder points to memory that was already freed.
But if you add tons of memory checking debug options to your Kernel
you'll also see:
- general protection fault: 0000
- BUG kmalloc-4096 (Tainted: G D W ): Poison overwritten
- INFO: Allocated in intel_ddi_init+0x65/0x270 [i915]
- INFO: Freed in intel_dp_encoder_destroy+0x69/0xb0 [i915]
Among a bunch of other error messages.
So this commit just destroys the sysfs files before both the encoder
and connectors are freed.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Fri, 27 Sep 2013 12:10:44 +0000 (15:10 +0300)]
drm/i915/dp: do not write DP_TRAINING_PATTERN_SET all the time
Neither the DP spec nor the compliance test spec state or imply that we
should write the DP_TRAINING_PATTERN_SET at every voltage swing and
pre-emphasis change. Indeed we probably shouldn't. So don't.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49402 Signed-off-by: Jani Nikula <jani.nikula@intel.com> Smoke-tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915/vlv: reduce GT FIFO error info to a debug message
It indicates a probable BIOS bug, but it appears to be harmless, and
there's nothing the user can do about it anyway, so reduce to a debug
msg. I've filed a bug with the BIOS folks about it anyway, so hopefully
they'll fix whatever GT SB read they were doing when the GT was off.
References: https://bugs.freedesktop.org/show_bug.cgi?id=69396 Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm: Code stereo layouts as an enum rather than a bit field
This allows us to use fewer bits in the mode structure, leaving room for
future work while allowing more stereo layouts types than we could have
ever dreamt of.
I also exposed the previously private DRM_MODE_FLAG_3D_MASK to set in
stone that we are using 5 bits for the stereo layout enum, reserving 32
values.
Even with that reservation, we gain 3 bits from the previous encoding.
The code adding the mandatory stereo modes needeed to be adapted as it was
relying or being able to or stereo layouts together.
Suggested-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915/vlv: use correct units for rc6 residency v2
We need to use the clock control reg to figure out how many CZ clks are in
30ns and use that as the basis for our RC6 residency calculations.
v2: use ULL everywhere for consistency (Chris)
factor out bias for clarity (Chris)
References: https://bugs.freedesktop.org/show_bug.cgi?id=69692 Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And add some reg defines while we're at it. Since the units of the RC6
residency counter are actually in CZ clocks, we want to just use the
high bits or we'll overflow too frequently.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 24 Sep 2013 18:26:19 +0000 (21:26 +0300)]
drm/i915: Use DIV_ROUND_CLOSEST()
vlv_find_best_dpll() has an open coded DIV_ROUND_CLOSEST(). Replace it
with the real thing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 24 Sep 2013 18:26:18 +0000 (21:26 +0300)]
drm/i915: Eliminate one indent leel from vlv_find_best_dpll
Use 'continue' to get rid of one indent level in vlv_find_best_dpll()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chon Ming Lee [Fri, 27 Sep 2013 07:31:00 +0000 (15:31 +0800)]
drm/i915: Program GMBUS Frequency based on the CDCLK for VLV.
CDCLK is used to generate the gmbus clock. This is normally done by
BIOS. Program the value if the BIOS-less system doesn't do it.
v2: Move this to intel_i2c_reset to allow reprogram the gmbus frequency
during resume. (Daniel)
v3: Change GMBUS_FREQ to GMBUSFREQ_VLV, and use VLV_DISPLAY_BASE.
(Ville).
Remove cdclk_ratio[] table, and calculate the cdclk ratio instead.
(Ville).
Change the shift then mask for reg read, to mask first, then shift.
(Ville).
Remove the gmbus frequency calculation = cdclk/1.01. Based on BIOS
programming, gmbus frequency = cdclk frequency. (Ville)
Add get_disp_clk_div, which can use to get cdclk/czclk divide.
v4: Fix the mmio_offset base for CZCLK_CDCLK_FREQ_RATIO, gmbus_freq
calculation, and duplicate check for gmbus_freq. (Ville)
In VLV, the spec is wrong about 4Mhz reference frequency for GMBUS. It
should be 1Mhz.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Add the comment Ville suggested. Also appease checkpatch a
bit.] Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915/vlv: hack to init backlight regs if BIOS fails to do so v2
Still digging up the actual VBT info for this, but wanted to get this
out there for testing, or in case others are also bugged by this.
This can happen if you boot with an external display connected. In that
case, the attached eDP backlight modulation frequency may not be
programmed, so we need to use something (in this case the value my BIOS
normally programs with just the internal display enabled).
v2: fix masking and magic value in read_blc_pwm_ctl (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67732 Tested-by: shui yangwei <yangweix.shui@intel.com> (v1) Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
struct drm_mode_display now has a separate crtc_ version of the clock to
be used when we're talking about the timings given to the harwadre (was
far as the mode is concerned).
This commit is really the result of a git grep adjusted_mode.*clock and
replacing those by adjusted_mode.crtc_clock. No functional change.
v2: Rebased on drm-intel-queued-next
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Acked-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm: Check the fb size against the adjusted v/hdisplay for stereo modes
Some stereo modes, like frame packing, need a larger CRTC viewport than
the "natural" underlying 2D mode and thus drm_crtc_check_viewport()
needs to query the adjusted mode to use the correct h/vdisplay.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Acked-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm: Factor out common CRTC viewport checking code
Both setcrtc and page_flip are checking that the framebuffer is big
enough for the defined crtc viewport (x, y, hdisplay, vdisplay). Factor
that code out in a single function.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Acked-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm: Implement timings adjustments for frame packing
When using the frame packing and a single big framebuffer, some hardware
requires that we do everything like if we were scanning out the big
buffer itself. Let's instrument drm_mode_set_crtcinfo() to be able to do
this adjustement if the driver is asking for it.
v2: Use crtc_vtotal and multiply the clock by 2 instead of
reconstructing it (Ville Syrjälä)
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Acked-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
projects / karo-tx-linux.git / log