drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
Power-up timing
The DS2408 is sensitive to the power-on slew rate and can inadvertently
power up with a test mode feature enabled. When this occurs, the P0 port
does not respond to the Channel Access Write command. For most reliable
operation, it is recommended to disable the test mode after every power-on
reset using the Disable Test Mode sequence shown below. The 64-bit ROM
code must be transmitted in the same bit sequence as with the Match ROM
command, i.e., least significant bit first. This precaution is
recommended in parasite power mode (VCC pin connected to GND) as well as
with VCC power.
Disable Test Mode:
RST,PD,96h,<64-bit DS2408 ROM Code>,3Ch,RST,PD
Remove the driver for Tsi500 Parallel RapidIO switch because this device
has not been available for several years. Since the first introduction of
Tsi500, the parallel RapidIO interface was replaced by the serial RapidIO
(sRIO) and therefore there is no value in keeping this driver.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Dan Carpenter [Thu, 9 May 2013 23:57:49 +0000 (09:57 +1000)]
mwave: fix info leak in mwave_ioctl()
Smatch complains that on 64 bit systems, there is a hole in the
MW_ABILITIES struct between ->component_count and ->component_list[]. It
leaks stack information from the mwave_ioctl() function.
I've added a memset() to initialize the struct to zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Greg KH <greg@kroah.com> Cc: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Jean Delvare [Thu, 9 May 2013 23:57:49 +0000 (09:57 +1000)]
idr: print a stack dump after ida_remove warning
We print a dump stack after idr_remove warning. This is useful to find
the faulty piece of code. Let's do the same for ida_remove, as it would
be equally useful there.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Tejun Heo <tj@kernel.org> Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Namjae Jeon [Thu, 9 May 2013 23:57:48 +0000 (09:57 +1000)]
fat: additions to support fat_fallocate
Implement preallocation via the fallocate syscall on VFAT partitions.
With FALLOC_FL_KEEP_SIZE, there is no way to distinguish if the mismatch
between i_size and no. of clusters allocated is a consequence of
fallocate or just plain corruption. When a non fallocate aware (old)
linux fat driver tries to write to such a file, it throws an error.Also,
fsck detects this as inconsistency and truncates the prealloc'd blocks.
To avoid this, as suggested by OGAWA, remove changes that make fallocate
persistent across mounts and restrict lifetime of blocks from fallocate(2)
to file release.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com> Signed-off-by: Ravishankar N <ravi.n1@samsung.com> Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com> Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Jeff Mahoney [Thu, 9 May 2013 23:57:48 +0000 (09:57 +1000)]
reiserfs: fix deadlock with nfs racing on create/lookup
Reiserfs is currently able to be deadlocked by having two NFS clients
where one has removed and recreated a file and another is accessing the
file with an open file handle.
If one client deletes and recreates a file with timing such that the
recreated file obtains the same [dirid, objectid] pair as the original
file while another client accesses the file via file handle, the create
and lookup can race and deadlock if the lookup manages to create the
in-memory inode first.
The create thread, in insert_inode_locked4, will hold the write lock while
waiting on the other inode to be unlocked. The lookup thread, anywhere in
the iget path, will release and reacquire the write lock while it
schedules. If it needs to reacquire the lock while the create thread has
it, it will never be able to make forward progress because it needs to
reacquire the lock before ultimately unlocking the inode.
This patch drops the write lock across the insert_inode_locked4 call so
that the ordering of inode_wait -> write lock is retained. Since this
would have been the case before the BKL push-down, this is safe.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Tony Prisk <linux@prisktech.co.nz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Wan Zongshun <mcuos.com@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Sachin Kamat [Thu, 9 May 2013 23:57:35 +0000 (09:57 +1000)]
drivers/rtc/rtc-x1205.c: fix checkpatch issues
Fixes the following types of issues:
ERROR: do not use assignment in if condition
ERROR: open brace '{' following struct go on the same line
ERROR: else should follow close brace '}'
WARNING: please, no space before tabs
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Cc: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Sachin Kamat [Thu, 9 May 2013 23:57:34 +0000 (09:57 +1000)]
drivers/rtc/rtc-rs5c313.c: fix spacing related issues
Fixes the following types of checkpatch issues:
WARNING: please, no space before tabs
ERROR: space prohibited after that open parenthesis '('
ERROR: space prohibited before that close parenthesis ')'
ERROR: need consistent spacing around '>>' (ctx:VxW)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Cc: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Sachin Kamat [Thu, 9 May 2013 23:57:32 +0000 (09:57 +1000)]
drivers/rtc/rtc-omap.c: include <linux/io.h> instead of <asm/io.h>
Use #include <linux/io.h> instead of <asm/io.h> as pointed out by
checkpatch.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Cc: George G. Davis <gdavis@mvista.com> Cc: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Sachin Kamat [Thu, 9 May 2013 23:57:29 +0000 (09:57 +1000)]
drivers/rtc/rtc-ds1511.c: fix issues related to spaces and braces
Fixes the following types of issues:
WARNING: please, no spaces at the start of a line
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Cc: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Sachin Kamat [Thu, 9 May 2013 23:57:28 +0000 (09:57 +1000)]
drivers/rtc/rtc-at91rm9200.c: include <linux/uaccess.h>
Silences the following checkpatch warning:
WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Cc: Andrew Victor <linux@maxim.org.za> Cc: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Sachin Kamat [Thu, 9 May 2013 23:57:27 +0000 (09:57 +1000)]
drivers/rtc/interface.c: fix checkpatch errors
Fixes the following types of errors:
ERROR: "foo* bar" should be "foo *bar"
ERROR: else should follow close brace '}'
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Cc: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Miklos Szeredi [Thu, 9 May 2013 23:57:26 +0000 (09:57 +1000)]
autofs4: translate pids to the right namespace for the daemon
The PID and the TGID of the process triggering the mount are sent to the
daemon. Currently the global pid values are sent (ones valid in the
initial pid namespace) but this is wrong if the autofs daemon itself is
not running in the initial pid namespace.
So send the pid values that are valid in the namespace of the autofs daemon.
The namespace to use is taken from the oz_pgrp pid pointer, which was set
at mount time to the mounting process' pid namespace.
If the pid translation fails (the triggering process is in an unrelated
pid namespace) then the automount fails with ENOENT.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Acked-by: Serge Hallyn <serge.hallyn@canonical.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Ian Kent <raven@themaw.net> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
autofs4: allow autofs to work outside the initial PID namespace
Enable autofs4 to work in a "container". oz_pgrp is converted from pid_t
to struct pid and this is stored at mount time based on the "pgrp=" option
or if the option is missing then the current pgrp.
The "pgrp=" option is interpreted in the PID namespace of the current
process. This option is flawed in that it doesn't carry the namespace
information, so it should be deprecated. AFAICS the autofs daemon always
sends the current pgrp, which is the default anyway.
The oz_pgrp is also set from the AUTOFS_DEV_IOCTL_SETPIPEFD_CMD ioctl.
This ioctl sets oz_pgrp to the current pgrp. It is not allowed to change
the pid namespace.
oz_pgrp is used mainly to determine whether the process traversing the
autofs mount tree is the autofs daemon itself or not. This function now
compares the pid pointers instead of the pid_t values.
One other use of oz_pgrp is in autofs4_show_options. There is shows the
virtual pid number (i.e. the one that is valid inside the PID namespace
of the calling process)
For debugging printk convert oz_pgrp to the value in the initial pid
namespace.
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Acked-by: Serge Hallyn <serge.hallyn@canonical.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Ian Kent <raven@themaw.net> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Steven Rostedt [Thu, 9 May 2013 23:57:25 +0000 (09:57 +1000)]
init: remove permanent string buffer from do_one_initcall()
do_one_initcall() uses a 64 byte string buffer to save a message. This
buffer is declared static and is only used at boot up and when a module
is loaded. As 64 bytes is very small, and this function has very limited
scope, there's no reason to waste permanent memory with this string and
not just simply put it on the stack.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We observed this problem has been occurring since 2.6.30 with
fs/binfmt_elf.c: create_elf_tables()->get_random_bytes(), introduced by f06295b44c296c8f ("ELF: implement AT_RANDOM for glibc PRNG seeding").
/*
* Generate 16 random bytes for userspace PRNG seeding.
*/
get_random_bytes(k_rand_bytes, sizeof(k_rand_bytes));
The patch introduces a wrapper around get_random_int() which has lower
overhead than calling get_random_bytes() directly.
With this patch applied:
$ cat /proc/sys/kernel/random/entropy_avail
2731
$ cat /proc/sys/kernel/random/entropy_avail
2802
$ cat /proc/sys/kernel/random/entropy_avail
2878
Analyzed by John Sobecki.
Signed-off-by: Jie Liu <jeff.liu@oracle.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Andreas Dilger <aedilger@gmail.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Arnd Bergmann <arnn@arndb.de> Cc: John Sobecki <john.sobecki@oracle.com> Cc: James Morris <james.l.morris@oracle.com> Cc: Jakub Jelinek <jakub@redhat.com> Cc: Ted Ts'o <tytso@mit.edu> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Kees Cook <keescook@chromium.org> Cc: Ulrich Drepper <drepper@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Chanho Min [Thu, 9 May 2013 23:57:24 +0000 (09:57 +1000)]
lib/bitmap.c: speed up bitmap_find_free_region
In bitmap_find_free_region(), if we skip the all-ones words and find bits
in a not-all-ones word, we can improve performance of it.
For example, If bitmap_find_free_region() is called with order=0, First,
It scans bitmap array by the increment of long type, then find 1 free bit
within 1 long type value. In 32 bits system and 1024 bits size, in the
worst case, We need 1024 for-loops to find 1 free bit. But, If this is
applied, it takes 64 for-loops. Instead, It will be needed additional
if-comparison of every word and It can take time slightly as 'Test case
3'. But, In many cases, It will speed up significantly.
Test cases bellows show the time taken to execute bitmap_find_free_region()
before and after patch.
Test case 1: order is 0. all bits are one except that last one bit is zero.
before patch: 29727 ns
after patch: 2349 ns
Test case 2: order is 1. all bits are one except that last 2 contiguous bits
are zero.
before patch: 15475 ns
after patch: 2225 ns
Test case 3: order is 1. all words are not-all-ones and don't have 2 contiguous
bits except that last 2 contiguous are zero.
before patch: 15475 ns
after patch: 16131 ns
Signed-off-by: Chanho Min <chanho.min@lge.com> Cc: Nadia Yvette Chambers <nyc@holomorphy.com> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Joe Perches <joe@perches.com> Cc: anish singh <anish198519851985@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
drivers/leds/leds-ot200.c: fix error caused by shifted mask
During the development of this driver an in-house register documentation
was used. The last week some integration tests were done and this problem
was found. It turned out that the released register documentation is
wrong.
The fix is very simple: shift all masks by one.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Bryan Wu <cooloney@gmail.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d063100 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure, since commit 0998d06310 ("device-core: Ensure drvdata =
NULL when no driver is bound"). Thus, it is not needed to manually clear
the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Chuansheng Liu [Thu, 9 May 2013 23:57:22 +0000 (09:57 +1000)]
smp: Give WARN()ing when calling smp_call_function_many()/single() in serving irq
Currently the functions smp_call_function_many()/single() will give a
WARN()ing only in the case of irqs_disabled(), but that check is not
enough to guarantee execution of the SMP cross-calls.
In many other cases such as softirq handling/interrupt handling, the two
APIs still can not be called, just as the smp_call_function_many()
comments say:
* You must not call this function with disabled interrupts or from a
* hardware interrupt handler or from a bottom half handler. Preemption
* must be disabled when calling this function.
There is a real case for softirq DEADLOCK case:
CPUA CPUB
spin_lock(&spinlock)
Any irq coming, call the irq handler
irq_exit()
spin_lock_irq(&spinlock)
<== Blocking here due to
CPUB hold it
__do_softirq()
run_timer_softirq()
timer_cb()
call smp_call_function_many()
send IPI interrupt to CPUA
wait_csd()
Then both CPUA and CPUB will be deadlocked here.
So we should give a warning in the nmi, hardirq or softirq context as well.
Moreover, adding one new macro in_serving_irq() which indicates we are
processing nmi, hardirq or sofirq.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Tested-by: Fengguang Wu <fengguang.wu@intel.com> Cc: Lai Jiangshan <eag0628@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
- fix comment indenting
- avoid inclusion of <asm/> files - use <linux/> where possible
- fix uniprocessor build (__dump_stack undefined)
- remove unneeded ifdef around smp.h inclusion
Cc: Alex Thorlton <athorlton@sgi.com> Cc: David S. Miller <davem@davemloft.net> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Richard Kuo <rkuo@codeaurora.org> Cc: Robin Holt <holt@sgi.com> Cc: Russ Anderson <rja@sgi.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: athorlton@sgi.com Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Alex Thorlton [Thu, 9 May 2013 23:57:21 +0000 (09:57 +1000)]
dump_stack: serialize the output from dump_stack()
tAdd adds functionality to serialize the output from dump_stack() to avoid
mangling of the output when dump_stack is called simultaneously from
multiple cpus.
Signed-off-by: Alex Thorlton <athorlton@sgi.com> Reported-by: Russ Anderson <rja@sgi.com> Reviewed-by: Robin Holt <holt@sgi.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Richard Kuo <rkuo@codeaurora.org> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Dan Carpenter [Thu, 9 May 2013 23:57:20 +0000 (09:57 +1000)]
err.h: IS_ERR() can accept __user pointers
Sparse generates a false positive when you pass a __user or __iomem
pointer to the IS_ERR() functions.
drivers/rtc/rtc-ds1286.c:344:36: sparse: incorrect type in argument 1 (different address spaces)
drivers/rtc/rtc-ds1286.c:344:36: expected void const *ptr
drivers/rtc/rtc-ds1286.c:344:36: got unsigned int [noderef] [usertype] <asn:2>*rtcregs
We can silence these by adding a __force here and upgrading to the
latest git release of Sparse.
This change has no effect when using current Sparse releases.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Christopher Li <sparse@chrisli.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Glauber Costa [Thu, 9 May 2013 23:57:19 +0000 (09:57 +1000)]
memcg: debugging facility to access dangling memcgs
If memcg is tracking anything other than plain user memory (swap, tcp buf
mem, or slab memory), it is possible - and normal - that a reference will
be held by the group after it is dead. Still, for developers, it would be
extremely useful to be able to query about those states during debugging.
This patch provides a debugging facility in the root memcg, so we can
inspect which memcgs still have pending objects, and what is the cause of
this state.
Signed-off-by: Glauber Costa <glommer@parallels.com> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Xi Wang [Thu, 9 May 2013 23:57:19 +0000 (09:57 +1000)]
mm/dmapool.c: fix null dev in dma_pool_create()
A few drivers invoke dma_pool_create() with a null dev. Note that dev is
dereferenced in dev_to_node(dev), causing a null pointer dereference.
A long term solution is to disallow null dev. Once the drivers are fixed,
we can simplify the core code here. For now we add WARN_ON(!dev) to
notify the driver maintainers and avoid the null pointer dereference.
Signed-off-by: Xi Wang <xi.wang@gmail.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Xi Wang [Thu, 9 May 2013 23:57:19 +0000 (09:57 +1000)]
drivers/usb/gadget/amd5536udc.c: avoid calling dma_pool_create() with NULL dev
Calling dma_pool_create() with dev==NULL will oops on a NUMA machine.
Rather than changing dma_pool_create() we wish to disallow passing
dev==NULL. This requires fixing up the small number of drivers which are
passing in dev==NULL.
Use &dev->pdev->dev instead of NULL.
Signed-off-by: Xi Wang <xi.wang@gmail.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
projects / karo-tx-linux.git / log