Hans Verkuil [Fri, 31 Dec 2010 14:47:23 +0000 (11:47 -0300)]
[media] v4l2-dev: don't memset video_device.dev
Zeroing video_device.dev causes a memory leak if video_set_drvdata
was called before video_register_device was called. video_set_drvdata
calls dev_set_drvdata which allocates video_device.dev.p.
memsetting this will prevent freeing of that memory.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] v4l: Fix a use-before-set in the control framework
v4l2_queryctrl sets the step value based on the control type. That would
be fine if it used the control type stored in the V4L2 kernel control
object, not the one stored in the userspace ioctl structure that has
just been memset to 0. Fix this.
Hans Verkuil [Sun, 16 Jan 2011 14:21:40 +0000 (11:21 -0300)]
[media] v4l2-ctrls: queryctrl shouldn't attempt to replace V4L2_CID_PRIVATE_BASE IDs
When queryctrl is called with a V4L2_CID_PRIVATE_BASE control ID, then
currently it is replaced by the real internal ID. This is not according to
the spec so keep the V4L2_CID_PRIVATE_BASE ID in this case.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sun, 16 Jan 2011 14:03:28 +0000 (11:03 -0300)]
[media] v4l2-ctrls: fix missing 'read-only' check
VIDIOC_S_CTRL did not check against read-only controls. Even worse, for
controls of type CTRL_CLASS it would cause a kernel oops since those controls
do not have a s_ctrl op.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Mon, 17 Jan 2011 00:21:03 +0000 (21:21 -0300)]
[media] pvrusb2: Provide more information about IR units to lirc_zilog and ir-kbd-i2c
When registering an IR Rx device with the I2C subsystem, provide more detailed
information about the IR device and default remote configuration for the IR
driver modules.
Also explicitly register any IR Tx device with the I2C subsystem.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Acked-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A commit for which I errantly recommended that defaults for I2C address
0x71 not be set by ir-kbd-i2c.c
The pvrusb2 and bttv drivers currently rely on ir-kbd-i2c setting
defaults for that address. Until I can get those bridge drivers fixed
to properly send IR_i2c_init_data for boards with Zilog Z8 chips,
just add back the default settings for I2C address 0x71.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 16 Jan 2011 01:32:33 +0000 (22:32 -0300)]
[media] lirc_zilog: Remove unneeded tests for existence of the IR Tx function
The driver is now structured so that it must handle an IR Tx unit
for a Z8 IR chip, or it refuses to handle that Z8 IR chip. This
allows us to assume that ir->tx != NULL in a few places in the driver,
and also allows us to always report Tx is available to userspace.
Get rid of unneeded tests for ir->tx == NULL and always report that
Tx is available.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 16 Jan 2011 01:02:05 +0000 (22:02 -0300)]
[media] lirc_zilog: Update IR Rx polling kthread start/stop and some printks
The IR Rx polling thread was originally a kernel_thread long ago,
and had only been minimally converted to a kthread. This patch
finishes that conversion by
- cleaning up all the unneeded completions
- destroying the kthread properly by calling kthread_stop()
- changing lirc_thread() to test kthread_should_stop() just before
every point where it may sleep
- reorganizing the lirc_thread() function so it uses fewer lines
- modifying the name of the kthread from "lirc_zilog" to
"zilog-rx-i2c-N", so ps will show which kthread polls
which Zilog Z8 IR unit.
Also some minor tweaks were made to logging emitted by the
ir_probe() function.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 15 Jan 2011 04:04:06 +0000 (01:04 -0300)]
[media] lirc_zilog: Extensive rework of ir_probe()/ir_remove()
This patch is an extensive rework of the ir_probe() and ir_remove() functions.
It removes all the double binding and allocation problems on module load.
It removes almost all the memory leaks on module exit and on device
instantiation failure. Proper destruction of the Rx polling kthread still
needs investigation and more work, but it is no worse than it already was.
This rework also had side effects that include:
- encapsulation of the ir_devices[] array
- serialization of access to the ir_devices[] array
- semantic change of the module parameter "disable_rx" to "tx_only"
If tx_only is true, the module does not claim the i2c_client for the IR Rx
function, and only claims and handles the i2c_client for the IR Tx function.
This is a first step in providing the option of letting ir-kbd-i2c.c handle
IR Rx function, while lirc_zilog handles the IR Tx function.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 15 Jan 2011 00:11:22 +0000 (21:11 -0300)]
[media] lirc_zilog: Don't make private copies of i2c clients
Don't make private copies of the i2c clients provided by the I2C
subsystem, don't change the client address field, and don't probe
the client addresses - the bridge driver already did that. This
moves us to the proper I2C and binding model.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Thu, 13 Jan 2011 05:00:33 +0000 (02:00 -0300)]
[media] lirc_zilog: Split struct IR into structs IR, IR_tx, and IR_rx
This change is a mostly mechanical break of the main struct IR
data structure into common, Rx, and Tx structures. There were some
small logical changes required as well, such as eliminating "is_hdpvr",
to accomplish this.
This change is an intiial step in reworking lirc_zilog to decouple the
Rx and Tx handling as much as possible to fit with the new I2C
binding model. This change actually makes lirc_zilog a little more
broken than it already was - memory deallocation in particular got worse.
However, this change makes the remaining problems easier to see and address.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only reason to use the lirc_zilog module is for IR Tx, so remove
the possibility of disabling IR Tx. If the user needs only IR Rx,
then the ir-kbd-i2c module works just fine, and doesn't require a
"firmware" image.
Signed-off-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stefan Richter [Sun, 16 Jan 2011 08:39:21 +0000 (05:39 -0300)]
[media] firedtv: fix remote control with newer Xorg evdev
After a recent update of xf86-input-evdev and xorg-server, I noticed
that X11 applications did not receive keypresses from the FireDTV
infrared remote control anymore. Instead, the Xorg log featured lots of
"FireDTV remote control: dropping event due to full queue!"
exclamations. The Linux console did not have an issue with the
FireDTV's RC though.
The fix is to insert EV_SYN events after the key-down/-up events.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| drivers/media/radio/radio-aimslab.c: In function ‘rt_decvol’:
| drivers/media/radio/radio-aimslab.c:76: error: implicit declaration of function ‘msleep’
Jarod Wilson [Thu, 6 Jan 2011 19:59:35 +0000 (16:59 -0300)]
[media] rc/imon: default to key mode instead of mouse mode
My initial thinking was that we should default to mouse mode, so people
could use the mouse function to click on something on a login screen,
but a lot of systems where a remote is useful automatically log in a
user and launch a media center application, some of which hide the
mouse, which can be confusing to users if they punch buttons on the
remote and don't see any feedback. Plus, first and foremost, its a
remote, so lets default to being a remote, and only toggle into mouse
mode when the user explicitly asks for it. As a nice side-effect, this
actually simplifies some of the code a fair bit...
Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Thu, 6 Jan 2011 19:59:36 +0000 (16:59 -0300)]
[media] rc: fix up and genericize some time unit conversions
The ene_ir driver was using a private define of MS_TO_NS, which is meant
to be microseconds to nanoseconds. The mceusb driver copied it,
intending to use is a milliseconds to microseconds. Lets move the
defines to a common location, expand and standardize them a touch, so
that we now have:
MS_TO_NS - milliseconds to nanoseconds
MS_TO_US - milliseconds to microseconds
US_TO_NS - microseconds to nanoseconds
Reported-by: David Härdeman <david@hardeman.nu> CC: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Thu, 6 Jan 2011 19:57:14 +0000 (16:57 -0300)]
[media] rc/imon: fix ffdc device detection oops
There's a nasty bug that slipped in when the rc device interface was
altered, only affecting the older 0xffdc imon devices. We were trying
to access ictx->rdev->allowed_protos before ictx->rdev had been set.
There's also an issue with call ordering that meant the correct
keymap wasn't getting loaded for MCE IR type 0xffdc devices.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tejun Heo [Mon, 3 Jan 2011 13:49:34 +0000 (10:49 -0300)]
[media] v4l/cx18: update workqueue usage
With cmwq, there's no reason to use separate out_work_queue. Drop it
and use system_wq instead. The in_work_queue needs to be ordered so
can't use one of the system wqs; however, as it isn't used to reclaim
memory, allocate the workqueue with alloc_ordered_workqueue() without
WQ_MEM_RECLAIM.
Signed-off-by: Tejun Heo <tj@kernel.org> Reviewed-by: Andy Walls <awalls@md.metrocast.net> Acked-by: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jesper Juhl [Sun, 2 Jan 2011 20:57:24 +0000 (17:57 -0300)]
[media] media, tlg2300: Fix memory leak in alloc_bulk_urbs_generic()
Hi,
While reading
drivers/media/video/tlg2300/pd-video.c::alloc_bulk_urbs_generic() I
noticed that
- We don't free the memory allocated to 'urb' if the call to
usb_alloc_coherent() fails.
- If the 'num' argument to the function is ever <= 0 we'll return an
uninitialized variable 'i' to the caller.
The following patch addresses both of the above by a) calling
usb_free_urb() when usb_alloc_coherent() fails and by explicitly
initializing 'i' to zero.
I also moved the variables 'mem' and 'urb' inside the for loop. This does
not actually make any difference, it just seemed more correct to me to let
variables exist only in the innermost scope they are used.
Jesper Juhl [Sun, 2 Jan 2011 19:14:03 +0000 (16:14 -0300)]
[media] frontends/ix2505v: Remember to free allocated memory in failure path
We may leak the storage allocated to 'state' in
drivers/media/dvb/frontends/ix2505v.c::ix2505v_attach() on error, as
it is too early to be able to call ix2505v_release().
This patch makes sure we free the allocated memory in the failure case.
[media] gspca - sonixj: Infrared bug fix and enhancement
The infrared was set by sensor write instead of bridge GPIO.
It is now settable by the standard control ILLUMINATOR_1.
A module parameter permits to set the right GPIO bit according
to the StarCam model.
Hans Verkuil [Tue, 11 Jan 2011 17:45:03 +0000 (14:45 -0300)]
[media] v4l2-ctrls: v4l2_ctrl_handler_setup must set is_new to 1
Renamed has_new to is_new.
Drivers can use the is_new field to determine if a new value was specified
for a control. The v4l2_ctrl_handler_setup() must always set this to 1 since
the setup has to force a full update of all controls.
Some subdevs need to call into the board code after they are registered
and have a valid struct v4l2_device pointer. The s_config op was abused
for this, but now that it is removed we need a cleaner way of solving this.
So this patch adds a struct with internal ops that the v4l2 core can call.
Currently only two ops exist: register and unregister. Subdevs can implement
these to call the board code and pass it the v4l2_device pointer, which the
board code can then use to get access to the struct that embeds the
v4l2_device.
It is expected that in the future open and close ops will also be added.
Hans Verkuil [Sat, 8 Jan 2011 10:08:02 +0000 (07:08 -0300)]
[media] v4l2-subdev: remove core.s_config and v4l2_i2c_new_subdev_cfg()
The core.s_config op was meant for legacy drivers that needed to work with old
pre-2.6.26 kernels. This is no longer relevant. Unfortunately, this op was
incorrectly called from several drivers.
Replace those occurences with proper i2c_board_info structs and call
v4l2_i2c_new_subdev_board.
After these changes v4l2_i2c_new_subdev_cfg() was no longer used, so remove
that function as well.
This is hacky and ugly. However, I coldn't find any easy way to fix it.
A proper fix would be to have a resource locking schema, used by both
V4L and DVB parts that would block access to analog registers while
digital registers are in use, but this will probably put tda829x into
a dead lock.
[media] mb86a20s: Be sure that device is initialized before starting DVB
Due to a hard to track bug between tda829x/tda18271/saa7134, tda829x
wants to go to analog mode during DVB initialization, causing some
I2C errors.
The analog failure doesn't cause any harm, as the device were already
properly initialized in analog mode. However, the failure at the digital
mode causes the frontend mb86a20s to not initialize. Fortunately, at
least on my tests, it was possible to detect that the device is a
mb86a20s before the failure.
What happens is that tda8290 is a very bad boy: during DVB setup, it
keeps insisting to call tda18271 analog_set_params, that calls
tune_agc code. The tune_agc code calls saa7134 driver, changing the
value of GPIO 27, switching from digital to analog mode and disabling
the access to mb86a20s, as, on Kworld SBTVD, the same GPIO used
to switch the hardware AGC mode seems to be used to enable the I2C
switch that allows access to the frontend (mb86a20s).
So, a call to analog_set_params ultimately disables the access to
the frontend, and causes a failure at the init frontend logic.
This patch is a workaround for this issue: it simply checks if the
frontend init had any failure. If so, it will init the frontend when
some DTV application will try to set DVB mode.
Even being a hack for Kworld SBTVD to work, and assumning that we could
teach tda8290 to be a good boy, this is actually an improvement at the
frontend driver, as it will be more reliable to initialization failures.
This happens because some I2C callbacks actually depend on having the
driver entirely initialized. To avoid this OOPS, just clean the I2C
callbacks, as if no device were detected.
Cc: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are a few bugs at the code that generates the scancode at dib0700:
- RC keycode is wrong (it outputs a 24 bits keycode);
- NEC extended outputs a keycode that have endiannes issues;
- keycode tables for NEC extended remotes need to be updated.
The last issue need to be done as we get reports, as we don't have
the complete NEC-extended keycodes at the dibcom table.
Hans Verkuil [Sat, 8 Jan 2011 12:53:32 +0000 (09:53 -0300)]
[media] v4l2-ioctl: fix incorrect error code if VIDIOC_DBG_G/S_REGISTER are unsupported
The ioctls VIDIOC_DBG_S_REGISTER and VIDIOC_DBG_G_REGISTER should return -EINVAL
if the driver didn't implement them. Currently they return -EPERM if called as
non-root user. However, this check should only be done if the driver actually
implemented these ioctls. Otherwise, just return -EINVAL as we do with all
unimplemented ioctls.
This bug make the v4l2-compliance test suite fail.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 6 Jan 2011 18:23:55 +0000 (15:23 -0300)]
[media] gspca_sonixj: Probe sensor type independent of bridge type
Looking at the windows inf file, for usb ids with a sensor type where probing
is needed to determine the type (for example ov7630 or soi768), this is
needed for all bridge variants with a usb id indicating this sensor type.
So do the probing to determine the actual sensor type for types where the
usb-id info is not 100% deterministic, independent of the bridge type.
If you look through the list of currently active usb ids in sonixj, this
effectively only changes the code path for 0c45:60fe (sn9c105 + ov7630) and
0c45:612e (sn9c110 + ov7630), which according to the inf file can have a
soi768 instead of a ov7630 just like the sn9c120 + ov7630 models where we
already probe for a soi7630.
The main reason for this code change is to keep the code paths as bridge
variant independent as possible, so that we don't need a lot of special
per bridge cases, as we enable more usb-ids in the future.
This change makes the 0c45:60fe code path identical to the successfully
tested 0c45:613e, so also make sonixj the default driver for 0c45:60fe.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 6 Jan 2011 16:05:29 +0000 (13:05 -0300)]
[media] gspca_sonixj: Enable more usb ids when sn9c102 gets compiled too
Both we and the windows driver make no sensor specific differences
(with some exceptions) for different sonixj bridge types. Thus if a
sn9c105 bridge has been successfully tested with a sensor, the same
sensor can be successfully used with a sn9c120 bridge too.
Using this knowledge we can move over most usb-ids too the sonixj
driver when both are compiled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 6 Jan 2011 14:56:30 +0000 (11:56 -0300)]
[media] gspca_sonixb: Add usb ids for known sn9c103 cameras
Now that our bridge code is unified for sn9c101/102 and sn9c103 models,
the sn9c103 models should simply work, given that the only difference
in the sn9c103 is audio support and a gamma correction table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 5 Jan 2011 16:55:43 +0000 (13:55 -0300)]
[media] gspca_sonixb: Refactor to unify bridge handling
Refactor the code to unify how the sn9c101/102 and the sn9c103 bridge
are handled. Also move code which is the same for all sensors from
the per sensor init register settings to a central place.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 5 Jan 2011 14:36:54 +0000 (11:36 -0300)]
[media] sn9c102: Remove not supported and non existing usb ids
The sn9c102 driver claims a number of usb-ids which are for cameras
with sensor types which it does not support. Also it claims a number
of usb-ids which do not exist at all (not present in the windows
drivers .inf files, not known by google).
This patch also fixes the conflict with the gspca_sonixj driver for the
0c45:60c0 and 0c45:60fb usb ids.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Mon, 3 Jan 2011 15:48:10 +0000 (12:48 -0300)]
[media] et61x251: remove wrongly claimed usb ids
The et61x251 driver claims a whole list of usb id's, but it only has
one sensor "module" which does sensor detection based on usb id and that
only supports devices with the 102c:6251 usb id. Remove the usb-ids for
other devices as for those the driver will fail with an unable to determine
sensor type message anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Fri, 31 Dec 2010 08:05:56 +0000 (05:05 -0300)]
[media] gspca_main: Simplify read mode memory type checks
gspca_dev->memory == GSPCA_MEMORY_NO implies gspca_dev->nframes == 0,
so there is no need to check for both in dev_poll. The check in
dev_read also is more complex then needed, as dqbuf which dev_read
calls already does all necessary checks. Moreover dqbuf is holding
the proper locks while checking where as dev_read itself is not.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Fri, 31 Dec 2010 07:51:36 +0000 (04:51 -0300)]
[media] gspca_main: Set memory type to GSPCA_MEMORY_NO on buffer release
Before this patch we were not setting the memory type to GSPCA_MEMORY_NO
when the buffers were released by the app doing a reqbufs 0. Nor would
the memory type be set to GSPCA_MEMORY_NO on device close, as capture_file
already is NULL on device close because of the reqbufs 0. This caused the
following problem:
-app1 does reqbufs USERPTR for 4 buffers
-app1 does reqbufs USERPTR for 0 buffers
-app2 tries to do reqbufs MMAP for 4 buffers
fails because gspca_dev->memory still is USERPTR
Fixing this also allows an app to switch memory type's by unrequesting
the buffers and re-requesting them of a different type.
This patch also moves the setting of gspca_dev->frsz and gscpa_dev->memory
to after alloc_frame succeeding, so that they are not changed when allocating
fails.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 30 Dec 2010 23:00:17 +0000 (20:00 -0300)]
[media] gspca_main: Update buffer flags even when user_copy fails
Before this patch dqbuf errors out on a failing user_copy (with user pointers)
before updating the buffer flags, causing a successsfully dequeued buffer
to still have the DONE flag, which means that it could no longer be
re-queueud (assuming the app somehow survives the segfault).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 30 Dec 2010 22:54:33 +0000 (19:54 -0300)]
[media] gspca_main: Locking fixes 2
Before this patch vidioc_dqbuf is using its own read_lock, where as
other queue related functions use queue_lock. This means that dqbuf is
accessing several variables in a racy manor. The most important one
being fr_o, which may be changed from underneath dqbuf by vidioc_reqbufs
or vidioc_streamoff. Other variables which it accesses unprotected
are gspca_dev->memory, gspca_dev->streaming and gspca_dev->capt_file.
This patch fixes this by changing vidioc_dqbuf to also use the queue_lock.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 30 Dec 2010 16:11:21 +0000 (13:11 -0300)]
[media] gspca_main: Locking fixes 1
The gspca_dev->streaming boolean is protected against multiple access
through gspca_dev->queue_lock everywhere except for 2 places. This patch
fixes this by bringing it under the lock in vidioc_streamoff. And by
removing the check for gspca_dev->streaming in gspca_disconnect,
the destroy_urbs call may be called multiple times (and is protected
by the usb_lock) and calling wake_up_interruptible can also always be done
safely.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Sat, 8 Jan 2011 00:59:11 +0000 (21:59 -0300)]
[media] af9013: fix AF9013 TDA18271 IF config
IF freq for DVB-T 7 MHz and 8 MHz was set slightly wrong. Due to that it
didn't worked at all (?) for 7 MHz channels and most likely performance
was dropped for 8 MHz channels.
That bug was pointed by few people during last two months. Thank you.
Trivial fix. Compile tested only due to lack of proper HW and signal.
Hans Verkuil [Wed, 5 Jan 2011 17:42:41 +0000 (14:42 -0300)]
[media] radio-gemtek-pci: remove duplicate driver
The radio-gemtek-pci driver is for the same hardware as the radio-maxiradio
driver which uses the same GemTek PR103 and tea5757 combination and the two
drivers are identical. I chose the maxiradio over the gemtek-pci driver since
the maxiradio has support for mono/stereo detection.
Tested with my gemtek-pci card.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mats Randgaard [Thu, 16 Dec 2010 15:17:43 +0000 (12:17 -0300)]
[media] vpif_cap/disp: Add support for DV presets
- Added functions to set/get/query/enum DV presets for vpif_caputre and
vpif_display.
- The format specification table is extended with all the DV formats
supported by TVP7002.
Mats Randgaard [Thu, 16 Dec 2010 15:17:42 +0000 (12:17 -0300)]
[media] vpif: Consolidate formats from capture and display
- The ch_params tables in vpif_capture.c and vpif_display.c are moved to a common
table in vpif.c. Then it is easier to maintain the table.
- The field "fps" is removed from the struct vpif_channel_config_params because it
is not used.
If there are out-of-tree users of this driver, then they can switch to tvaudio
instead.
The original commit message read as follows:
This change allows bttv to use tvaudio for this device. Since this device
has the same i2c address as the tda9874 we need to support both in the same
tvaudio driver. This makes it possible for tvaudio to detect which chip is
used. Originally the tda9875 was only available in the dedicated tda9875
driver, but that makes life very hard for bttv since loading tvaudio might
misdetect a tda9875 as a tda9874.
So there were good reasons for moving the tda9875 code into tvaudio.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linus Torvalds [Tue, 18 Jan 2011 22:29:37 +0000 (14:29 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Validate cpu early in perf_event_alloc()
perf: Find_get_context: fix the per-cpu-counter check
perf: Fix contexted inheritance
Linus Torvalds [Tue, 18 Jan 2011 22:29:21 +0000 (14:29 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Clear irqstack thread_info
x86: Make relocatable kernel work with new binutils
projects / linux-beck.git / log