Ricky Liang [Tue, 28 Jun 2016 07:06:57 +0000 (15:06 +0800)]
Bluetooth: btmrvl: fix slab-out-of-bounds access in btmrvl_sdio
Kasan reported slab-out-of-bounds access in btmrvl_sdio:
[ 33.055400] ==================================================================
[ 33.062585] BUG: KASAN: slab-out-of-bounds in memcpy+0x24/0x50 at addr ffffffc0d89b4a00
[ 33.070529] Read of size 256 by task btmrvl_main_ser/3576
[ 33.075885] =============================================================================
[ 33.084002] BUG kmalloc-256 (Tainted: G B ): kasan: bad access detected
[ 33.091511] -----------------------------------------------------------------------------
<snip...>
[ 33.413498] Call trace:
[ 33.415928] [<ffffffc00020a440>] dump_backtrace+0x0/0x190
[ 33.421288] [<ffffffc00020a5ec>] show_stack+0x1c/0x28
[ 33.426305] [<ffffffc000b3288c>] dump_stack+0xa0/0xf8
[ 33.431320] [<ffffffc000396130>] print_trailer+0x158/0x16c
[ 33.436765] [<ffffffc0003962cc>] object_err+0x48/0x5c
[ 33.441780] [<ffffffc00039be24>] kasan_report+0x344/0x510
[ 33.447141] [<ffffffc00039afd8>] __asan_loadN+0x20/0x150
[ 33.452413] [<ffffffc00039b60c>] memcpy+0x20/0x50
[ 33.457084] [<ffffffc000595fcc>] swiotlb_tbl_map_single+0x2ec/0x310
[ 33.463305] [<ffffffc000596b54>] map_single+0x24/0x30
[ 33.468320] [<ffffffc0005970c8>] swiotlb_map_sg_attrs+0xec/0x21c
[ 33.474286] [<ffffffc000219d4c>] __swiotlb_map_sg_attrs+0x48/0xec
[ 33.480339] [<ffffffc0008ea610>] msdc_prepare_data.isra.11+0xf0/0x11c
[ 33.486733] [<ffffffc0008ecbd0>] msdc_ops_request+0x74/0xf0
[ 33.492266] [<ffffffc0008c6b38>] __mmc_start_request+0x78/0x8c
[ 33.498057] [<ffffffc0008c6d6c>] mmc_start_request+0x220/0x240
[ 33.503848] [<ffffffc0008c6e04>] mmc_wait_for_req+0x78/0x250
[ 33.509468] [<ffffffc0008d70fc>] mmc_io_rw_extended+0x2ec/0x388
[ 33.515347] [<ffffffc0008d8fc0>] sdio_io_rw_ext_helper+0x160/0x268
[ 33.521483] [<ffffffc0008d93fc>] sdio_writesb+0x40/0x50
[ 33.526677] [<ffffffbffc338b38>] btmrvl_sdio_host_to_card+0x124/0x1bc [btmrvl_sdio]
[ 33.534283] [<ffffffbffc3290a0>] btmrvl_service_main_thread+0x384/0x428 [btmrvl]
[ 33.541626] [<ffffffc0002518e8>] kthread+0x140/0x158
[ 33.546550] Memory state around the buggy address:
[ 33.551305] ffffffc0d89b4980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 33.558474] ffffffc0d89b4a00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 33.565643] >ffffffc0d89b4a80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fc
[ 33.572809] ^
[ 33.579889] ffffffc0d89b4b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 33.587055] ffffffc0d89b4b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 33.594221] ==================================================================
The cause of this is that btmrvl_sdio_host_to_card can access memory region
out of its allocated space due to:
1. the requested block size is smaller than SDIO_BLOCK_SIZE, and/or
2. the allocated memory is not BTSDIO_DMA_ALIGN-aligned.
This patch fixes the issue by allocating a buffer which is big enough for
SDIO_BLOCK_SIZE transfer and/or BTSDIO_DMA_ALIGN address relocation.
Tedd Ho-Jeong An [Tue, 28 Jun 2016 15:56:39 +0000 (08:56 -0700)]
Bluetooth: Replace constant hw_variant from Intel Bluetooth firmware filename
The format of Intel Bluetooth firmware filename for bootloader product
is ibt-<hw_variant>-<device_revision_id>.sfi
Currently the driver uses a constant value 11 (0x0b) for hw_variant
to support LnP/SfP product. But new product like WsP product has
a different value such as 12 (0x0c).
To support the multiple products, this patch replaces the constant
value of hw_variant to the actual hw_variant value read from
the device.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Denis Kenzior [Mon, 27 Jun 2016 16:01:13 +0000 (11:01 -0500)]
Bluetooth: Fix hci_sock_recvmsg return value
If recvmsg is called with a destination buffer that is too small to
receive the contents of skb in its entirety, the return value from
recvmsg was inconsistent with common SOCK_SEQPACKET or SOCK_DGRAM
semantics.
If destination buffer provided by userspace is too small (e.g. len <
copied), then MSG_TRUNC flag is set and copied is returned. Instead, it
should return the length of the message, which is consistent with how
other datagram based sockets act. Quoting 'man recv':
"All three calls return the length of the message on successful comple‐
tion. If a message is too long to fit in the supplied buffer, excess
bytes may be discarded depending on the type of socket the message is
received from."
and
"MSG_TRUNC (since Linux 2.2)
For raw (AF_PACKET), Internet datagram (since Linux
2.4.27/2.6.8), netlink (since Linux 2.6.22), and UNIX datagram
(since Linux 3.4) sockets: return the real length of the packet
or datagram, even when it was longer than the passed buffer."
Denis Kenzior [Mon, 27 Jun 2016 16:01:12 +0000 (11:01 -0500)]
Bluetooth: Fix bt_sock_recvmsg return value
If recvmsg is called with a destination buffer that is too small to
receive the contents of skb in its entirety, the return value from
recvmsg was inconsistent with common SOCK_SEQPACKET or SOCK_DGRAM
semantics.
If destination buffer provided by userspace is too small (e.g. len <
copied), then MSG_TRUNC flag is set and copied is returned. Instead, it
should return the length of the message, which is consistent with how
other datagram based sockets act. Quoting 'man recv':
"All three calls return the length of the message on successful comple‐
tion. If a message is too long to fit in the supplied buffer, excess
bytes may be discarded depending on the type of socket the message is
received from."
and
"MSG_TRUNC (since Linux 2.2)
For raw (AF_PACKET), Internet datagram (since Linux
2.4.27/2.6.8), netlink (since Linux 2.6.22), and UNIX datagram
(since Linux 3.4) sockets: return the real length of the packet
or datagram, even when it was longer than the passed buffer."
Alexander Aring [Sat, 18 Jun 2016 08:45:35 +0000 (10:45 +0200)]
ieee802154: allow netns create of lowpan interface
This patch reverts commit f9d1ce8f81eb ("ieee802154: fix netns settings").
The lowpan interface need to be created inside the net namespace where
the wpan interface is available. The wpan namespace can be changed only
by nl802154 before. Without this patch it's not possible to create a
lowpan interface for a wpan interface which isn't inside init_net
namespace.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Sat, 18 Jun 2016 08:45:33 +0000 (10:45 +0200)]
nl802154: move PAD to right position
The PAD define should be above the experimental support. We don't care
about if we break userspace in experimental stuff but PAD is part of the
existing UAPI.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: Stefan Schmidt<stefan@osg.samsung.com> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Andy Lutomirski [Sun, 26 Jun 2016 21:55:23 +0000 (14:55 -0700)]
Bluetooth: Switch SMP to crypto_cipher_encrypt_one()
SMP does ECB crypto on stack buffers. This is complicated and
fragile, and it will not work if the stack is virtually allocated.
Switch to the crypto_cipher interface, which is simpler and safer.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Johan Hedberg <johan.hedberg@intel.com> Tested-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
David S. Miller [Thu, 7 Jul 2016 05:32:15 +0000 (22:32 -0700)]
Merge tag 'mac80211-next-for-davem-2016-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One more set of new features:
* beacon report (for radio measurement) support in cfg80211/mac80211
* hwsim: allow wmediumd in namespaces
* mac80211: extend 160MHz workaround to CSA IEs
* mesh: properly encrypt group-addressed privacy action frames
* mesh: allow setting peer AID
* first steps for MU-MIMO monitor mode
* along with various other cleanups and improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
1) All users of AF_PACKET's fanout feature want a symmetric packet
header hash for load balancing purposes, so give it to them.
2) Fix vlan state synchronization in e1000e, from Jarod Wilson.
3) Use correct socket pointer in ip_skb_dst_mtu(), from Shmulik
Ladkani.
4) mlx5 bug fixes from Mohamad Haj Yahia, Daniel Jurgens, Matthew
Finlay, Rana Shahout, and Shaker Daibes. Mostly to do with
operation timeouts and PCI error handling.
5) Fix checksum handling in mirred packet action, from WANG Cong.
6) Set skb->dev correctly when transmitting in !protect_frames case of
macsec driver, from Daniel Borkmann.
7) Fix MTU calculation in geneve driver, from Haishuang Yan.
8) Missing netif_napi_del() in unregister path of qeth driver, from
Ursula Braun.
9) Handle malformed route netlink messages in decnet properly, from
Vergard Nossum.
10) Memory leak of percpu data in ipv6 routing code, from Martin KaFai
Lau.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
ipv6: Fix mem leak in rt6i_pcpu
net: fix decnet rtnexthop parsing
cxgb4: update latest firmware version supported
net/mlx5: Avoid setting unused var when modifying vport node GUID
bonding: fix enslavement slave link notifications
r8152: fix runtime function for RTL8152
qeth: delete napi struct when removing a qeth device
Revert "fsl/fman: fix error handling"
fsl/fman: fix error handling
cdc_ncm: workaround for EM7455 "silent" data interface
RDS: fix rds_tcp_init() error path
geneve: fix max_mtu setting
net: phy: dp83867: Fix initialization of PHYCR register
enc28j60: Fix race condition in enc28j60 driver
net: stmmac: Fix null-function call in ISR on stmmac1000
tipc: fix nl compat regression for link statistics
net: bcmsysport: Device stats are unsigned long
macsec: set actual real device for xmit when !protect_frames
net_sched: fix mirrored packets checksum
packet: Use symmetric hash for PACKET_FANOUT_HASH.
...
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next,
they are:
1) Don't use userspace datatypes in bridge netfilter code, from
Tobin Harding.
2) Iterate only once over the expectation table when removing the
helper module, instead of once per-netns, from Florian Westphal.
3) Extra sanitization in xt_hook_ops_alloc() to return error in case
we ever pass zero hooks, xt_hook_ops_alloc():
4) Handle NFPROTO_INET from the logging core infrastructure, from
Liping Zhang.
5) Autoload loggers when TRACE target is used from rules, this doesn't
change the behaviour in case the user already selected nfnetlink_log
as preferred way to print tracing logs, also from Liping Zhang.
6) Conntrack slabs with SLAB_HWCACHE_ALIGN to allow rearranging fields
by cache lines, increases the size of entries in 11% per entry.
From Florian Westphal.
7) Skip zone comparison if CONFIG_NF_CONNTRACK_ZONES=n, from Florian.
8) Remove useless defensive check in nf_logger_find_get() from Shivani
Bhardwaj.
9) Remove zone extension as place it in the conntrack object, this is
always include in the hashing and we expect more intensive use of
zones since containers are in place. Also from Florian Westphal.
10) Owner match now works from any namespace, from Eric Bierdeman.
11) Make sure we only reply with TCP reset to TCP traffic from
nf_reject_ipv4, patch from Liping Zhang.
12) Introduce --nflog-size to indicate amount of network packet bytes
that are copied to userspace via log message, from Vishwanath Pai.
This obsoletes --nflog-range that has never worked, it was designed
to achieve this but it has never worked.
13) Introduce generic macros for nf_tables object generation masks.
14) Use generation mask in table, chain and set objects in nf_tables.
This allows fixes interferences with ongoing preparation phase of
the commit protocol and object listings going on at the same time.
This update is introduced in three patches, one per object.
15) Check if the object is active in the next generation for element
deactivation in the rbtree implementation, given that deactivation
happens from the commit phase path we have to observe the future
status of the object.
16) Support for deletion of just added elements in the hash set type.
17) Allow to resize hashtable from /proc entry, not only from the
obscure /sys entry that maps to the module parameter, from Florian
Westphal.
18) Get rid of NFT_BASECHAIN_DISABLED, this code is not exercised
anymore since we tear down the ruleset whenever the netdevice
goes away.
19) Support for matching inverted set lookups, from Arturo Borrero.
20) Simplify the iptables_mangle_hook() by removing a superfluous
extra branch.
21) Introduce ether_addr_equal_masked() and use it from the netfilter
codebase, from Joe Perches.
22) Remove references to "Use netfilter MARK value as routing key"
from the Netfilter Kconfig description given that this toggle
doesn't exists already for 10 years, from Moritz Sichert.
23) Introduce generic NF_INVF() and use it from the xtables codebase,
from Joe Perches.
24) Setting logger to NONE via /proc was not working unless explicit
nul-termination was included in the string. This fixes seems to
leave the former behaviour there, so we don't break backward.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'sound-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a collection of small fixes: at this time, we've got a
slightly high amount, but all small and trivial fixes, and nothing
scary can be seen there"
* tag 'sound-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
ALSA: hda/realtek: Add Lenovo L460 to docking unit fixup
ALSA: timer: Fix negative queue usage by racy accesses
ASoC: rt5645: fix reg-2f default value.
ASoC: fsl_ssi: Fix number of words per frame for I2S-slave mode
ALSA: au88x0: Fix calculation in vortex_wtdma_bufshift()
ALSA: hda - Add PCI ID for Kabylake-H
ALSA: echoaudio: Fix memory allocation
ASoC: Intel: atom: fix missing breaks that would cause the wrong operation to execute
ALSA: hda - fix read before array start
ASoC: cx20442: set tty->receiver_room in v253_open
ASoC: ak4613: Enable cache usage to fix crashes on resume
ASoC: wm8940: Enable cache usage to fix crashes on resume
ASoC: Intel: Skylake: Initialize module list for Broxton
ASoC: wm5102: Correct supported channels on trace compressed DAI
ASoC: wm5110: Add missing route from OUT3R to SYSCLK
ASoC: rt5670: fix HP Playback Volume control
ASoC: hdmi-codec: select CONFIG_HDMI
ASoC: davinci-mcasp: Fix dra7 DMA offset when using CFG port
ASoC: hdac_hdmi: Fix potential NULL dereference
ASoC: ak4613: Remove owner assignment from platform_driver
...
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
adds mesh peer AID setting API.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 5 Jul 2016 12:23:14 +0000 (15:23 +0300)]
mac80211: parse wide bandwidth channel switch IE with workaround
Continuing the workaround implemented in commit 23665aaf9170
("mac80211: Interoperability workaround for 80+80 and 160 MHz channels")
use the same code to parse the Wide Bandwidth Channel Switch element
by converting to VHT Operation element since the spec also just refers
to that for parsing semantics, particularly with the workaround.
While at it, remove some dead code - the IEEE80211_STA_DISABLE_40MHZ
flag can never be set at this point since it's checked earlier and the
wide_bw_chansw_ie pointer is set to NULL if it's set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: Add support for beacon report radio measurement
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API] Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: David Spinadel <david.spinadel@intel.com> Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Tue, 5 Jul 2016 12:23:09 +0000 (15:23 +0300)]
mac80211_hwsim: Add radar bandwidths to the P2P Device combination
Add radar_detect_widths to the interface combination that allows
concurrent P2P Device dedicated interface and AP interfaces, to enable
testing of radar detection when P2P Device interface is used.
Clear the radar_detect_widths in case of multi channel contexts
as this is not currently supported.
As radar_detect_widths are now supported in all combinations,
remove the hwsim_if_dfs_limits definition since it is no longer
needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211: Add API to support VHT MU-MIMO air sniffer
add API to support VHT MU-MIMO air sniffer.
in MU-MIMO there are parallel frames on the air while the HW
has only one RX.
add the capability to sniff one of the MU-MIMO parallel frames by
giving the sniffer additional information so it'll know which
of the parallel frames it shall follow.
Add attribute - NL80211_ATTR_MU_MIMO_GROUP_DATA - for getting
a MU-MIMO groupID in order to monitor packets from that group
using VHT MU-MIMO.
And add attribute -NL80211_ATTR_MU_MIMO_FOLLOW_ADDR - for passing
MAC address to monitor mode.
that option will be used by VHT MU-MIMO air sniffer to follow a
station according to it's MAC address using VHT MU-MIMO.
Johannes Berg [Wed, 6 Jul 2016 12:44:14 +0000 (14:44 +0200)]
mac80211: agg-rx: refuse ADDBA Request with timeout update
The current implementation of handling ADDBA Request while a session
is already active with the peer is wrong - in case the peer is using
the existing session's dialog token this should be treated as update
to the session, which can update the timeout value.
We don't really have a good way of supporting that, so reject, but
implement the required behaviour in the spec of "Even if the updated
ADDBA Request frame is not accepted, the original Block ACK setup
remains active." (802.11-2012 10.5.4)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was first reported and reproduced by Petr (thanks!) in
https://bugzilla.kernel.org/show_bug.cgi?id=119581
free_percpu(rt->rt6i_pcpu) used to always happen in ip6_dst_destroy().
However, after fixing a deadlock bug in
commit 9c7370a166b4 ("ipv6: Fix a potential deadlock when creating pcpu rt"),
free_percpu() is not called before setting non_pcpu_rt->rt6i_pcpu to NULL.
It is worth to note that rt6i_pcpu is protected by table->tb6_lock.
kmemleak somehow did not report it. We nailed it down by
observing the pcpu entries in /proc/vmallocinfo (first suggested
by Hannes, thanks!).
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Fixes: 9c7370a166b4 ("ipv6: Fix a potential deadlock when creating pcpu rt") Reported-by: Petr Novopashenniy <pety@rusnet.ru> Tested-by: Petr Novopashenniy <pety@rusnet.ru> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Petr Novopashenniy <pety@rusnet.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
dn_fib_count_nhs() could enter an infinite loop if nhp->rtnh_len == 0
(i.e. if userspace passes a malformed netlink message).
Let's use the helpers from net/nexthop.h which take care of all this
stuff. We can do exactly the same as e.g. fib_count_nexthops() and
fib_get_nhs() from net/ipv4/fib_semantics.c.
This fixes the softlockup for me.
Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 21 Jun 2016 13:58:46 +0000 (16:58 +0300)]
platform/chrome: cros_ec_dev - double fetch bug in ioctl
We verify "u_cmd.outsize" and "u_cmd.insize" but we need to make sure
that those values have not changed between the two copy_from_user()
calls. Otherwise it could lead to a buffer overflow.
Additionally, cros_ec_cmd_xfer() can set s_cmd->insize to a lower value.
We should use the new smaller value so we don't copy too much data to
the user.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com> Fixes: a841178445bb ('mfd: cros_ec: Use a zero-length array for command data') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Kees Cook <keescook@chromium.org> Tested-by: Gwendal Grignou <gwendal@chromium.org> Cc: <stable@vger.kernel.org> # v4.2+ Signed-off-by: Olof Johansson <olof@lixom.net>
Or Gerlitz [Tue, 5 Jul 2016 09:17:12 +0000 (12:17 +0300)]
net/mlx5: Avoid setting unused var when modifying vport node GUID
GCC complains on unused-but-set-variable, clean this up.
Fixes: 23898c763f4a ('net/mlx5: E-Switch, Modify node guid on vf set MAC') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, link notifications are not sent by
bond_set_slave_link_state() upon enslavement if
the slave is enslaved when up.
This happens because slave->link default init value
is 0, which is the same as BOND_LINK_UP, resulting
in bond_set_slave_link_state() ignoring this transition.
This patch sets the default value of slave->link to
BOND_LINK_NOCHANGE, assuring it will count as a state
transition and thus trigger notification logic.
Signed-off-by: Aviv Heller <avivh@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 5 Jul 2016 01:47:41 +0000 (18:47 -0700)]
net: vrf: Add support for PREROUTING rules on vrf device
Add support for PREROUTING rules with skb->dev set to the vrf device.
INPUT rules are already allowed. Provides symmetry with the output path
which allows POSTROUTING rules.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker [Mon, 4 Jul 2016 21:50:58 +0000 (17:50 -0400)]
connector: make cn_proc explicitly non-modular
The Kconfig controlling build of this code is currently:
drivers/connector/Kconfig:config PROC_EVENTS
drivers/connector/Kconfig: bool "Report process events to userspace"
...meaning that it currently is not being built as a module by anyone.
Lets remove the two modular references, so that when reading the driver
there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Cc: Evgeniy Polyakov <zbr@ioremap.net> Cc: netdev@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns: fix return value check in hns_dsaf_get_cfg()
In case of error, function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset enables IPv4 unicast routing in the Mellanox Spectrum ASIC
switch driver. This builds upon the work that was done by a couple of
previous patchsets.
Patches 1,2,6 add a couple of dependencies outside the driver. Namely, the
ability to propagate ndo_neigh_construct()/destroy() through stacked devices and
a notification whenever DELAY_PROBE_TIME changes. When propagated down, the
ndos allow drivers to add and remove neighbour entries from their private
neighbour table. The DELAY_PROBE_TIME notification gives drivers the ability to
correctly configure their polling interval for neighbour activity, so that
active neighbour won't be marked as STALE.
Patches 3-5,7-8 add the neighbour offloading infrastructure, where patch 7 uses
the DELAY_PROBE_TIME notification in order to correctly configure the device's
polling interval. Patch 8 finally programs neighbours to the device's table
based on NEIGH_UPDATE notifications, so that directly connected routes can
be used.
Patches 9-16 build upon the previous patches and extend the router with
remote routes (nexthop) support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, the driver sends arp probes for all unresolved neighbours that are
currently a nexthop for some route on the system. The job is set
periodically every 5 seconds.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_router: Add the nexthop neigh activity update
For nexthop neighbours we need to make kernel to think there is a traffic
flowing to them preventing it from going to stale state. Otherwise
kernel would stale it and eventually the neigh would be removed from HW
and nexthop as well. That would reduce ECMP group in HW.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Implement next-hop routing offload including ECMP. To make it possible,
introduce next-hop group entity. This entity keeps track of resolved
neighbours and updates HW adjacency table accordingly. Note that HW
next-hops are stored in this adjacency table, in form of MAC.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: Introduce simplistic KVD linear area manager
This is a very simple manager for KVD linear area. Currently, the
allocator will either allocate a single entry from pre-defined sub-area,
or in case more than one entry is needed, it will allocate 32-entry chunk
in other pre-defined sub-area.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_router: Offload neighbours based on NUD state change
Listen to any NEIGH_UPDATE events sent and program the device
accordingly. If NUD state is VALID and neighbour isn't yet offloaded,
then program it into the device's table. Otherwise, just edit its
parameters.
If NUD state machine transitioned neighbour out of VALID state and it's
present in the device's table, then remove it.
Note that the device is programmed in delayed work, as the netevent
notification chain is atomic and prevents us from going to sleep.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_router: Periodically update the kernel's neigh table
As previously explained, the driver should periodically poll the device
for neighbours activity according to the configured DELAY_PROBE_TIME.
This will prevent active neighbours from staying in STALE state for long
periods of time.
During init configure the polling interval according to the
DELAY_PROBE_TIME used in the default table. In addition, register a
netevent notification block, so that the interval is updated whenever
DELAY_PROBE_TIME changes.
Using the computed interval schedule a delayed work, which will update
the kernel via neigh_event_send() on any active neighbour since the last
delayed work.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
neigh: Send a notification when DELAY_PROBE_TIME changes
When the data plane is offloaded the traffic doesn't go through the
networking stack. Therefore, after first resolving a neighbour the NUD
state machine will transition it from REACHABLE to STALE until it's
finally deleted by the garbage collector.
To prevent such situations the offloading driver should notify the NUD
state machine on any neighbours that were recently used. The driver's
polling interval should be set so that the NUD state machine can
function as if the traffic wasn't offloaded.
Currently, there are no in-tree drivers that can report confirmation for
a neighbour, but only 'used' indication. Therefore, the polling interval
should be set according to DELAY_FIRST_PROBE_TIME, as a neighbour will
transition from REACHABLE state to DELAY (instead of STALE) if "a packet
was sent within the last DELAY_FIRST_PROBE_TIME seconds" (RFC 4861).
Send a netevent whenever the DELAY_FIRST_PROBE_TIME changes - either via
netlink or sysctl - so that offloading drivers can correctly set their
polling interval.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The RAUHT register is used to configure and query the Unicast Host Table
in devices that implement the Algorithmic LPM. In other words, it is
used to configure neighbour entries in the device.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We need to hold some private data for every neigh entry. It would be
possible to do it using neigh_priv_len/ndo_neigh_construct/
ndo_neigh_destroy however only for the port device itself. That would not
work for stacked devices like bridge/team/bond. So introduce a private
neigh table. Hook onto ndos neigh_construct/destroy and add/remove
table entry according to that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: introduce default neigh_construct/destroy ndo calls for L2 upper devices
L2 upper device needs to propagate neigh_construct/destroy calls down to
lower devices. Do this by defining default ndo functions and use them in
team, bond, bridge and vlan.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of taking one interrupt per packet transmitted, re-use the same
NAPI context to free transmitted buffers. Since we are no longer in hard
IRQ context replace dev_kfree_skb_irq() by dev_kfree_skb().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pad the SKB to the minimum length of ETH_ZLEN by using skb_put_padto()
and take this operation out of the critical section since there is no
need to check any HW resources before doing that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: r6040: Increase statistics upon transmit completion
r6040_xmit() is increasing transmit statistics during transmission while
this may still fail, do this in r6040_tx() where we complete transmitted
buffers instead.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series adds Ethernet ethtool ntuple steering 'ethtool -N|U' and exposes two more
counter sets to Ethtool statistics, RDMA vport and global flow control statistics.
We start from three refactoring patches of the flow steering infrastructure
- mlx5_add_flow_rule will now receive mlx5 flow spec to simplify and reduce
number of parameters
- All low level steering objects are now wrapped in mlx5_flow_steering structure
for better encapsulation
- Flow steering object will now be removed properly and generically rather than
traversing on a well-known steering tree objects
Patch#4 adds the infrastructure and the data structures needed for the ethtool ntuple
steering, all implemented in a new file 'en_fs_ethtool.c'. Add the support for set_rxnfc
ethtool callback to add/remove/replace a flow spec of ethter type L2.
Patch#5 adds the support for L3/L4 flow specs and a higher priority in favor for L3/L4
rules when interleaving with L2 rules.
Patch#6 adds the support for get_rxnfc ethtool callback.
Patch#7,8 adds RDMA vport and global flow control statistics.
Gal Pressman [Mon, 4 Jul 2016 14:23:12 +0000 (17:23 +0300)]
net/mlx5e: Expose flow control counters to ethtool
Just like per prio counters, the global flow counters are queried from
per priority counters register.
Global flow control counters are stored in priority 0 PFC counters.
Signed-off-by: Gal Pressman <galp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Mon, 4 Jul 2016 14:23:11 +0000 (17:23 +0300)]
net/mlx5e: Expose RDMA VPort counters to ethtool
Add the needed descriptors to expose RoCE RDMA counters.
Signed-off-by: Gal Pressman <galp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Mon, 4 Jul 2016 14:23:10 +0000 (17:23 +0300)]
net/mlx5e: Add support to get ethtool flow rules
Enhance the existing get_rxnfc callback:
1. Get flow rule of specific ID.
2. Get all flow rules.
3. Get number of rules.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Mon, 4 Jul 2016 14:23:09 +0000 (17:23 +0300)]
net/mlx5e: Support l3/l4 flow type specs in ethtool flow steering
Add support to add flow steering rules with ethtool
of L3/L4 flow types (ip4/tcp4/udp4).
Those rules will be in higher priority than l2 flow rules, in order
to prefer more specific rules.
Mask is not supported for l3/l4 flow types.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Mon, 4 Jul 2016 14:23:08 +0000 (17:23 +0300)]
net/mlx5e: Add ethtool flow steering support
Implement etrhtool set_rxnfc callback to support ethtool flow spec
direct steering. This patch adds only the support of ether flow type
spec. L3/L4 flow specs support will be added in downstream patches.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Mon, 4 Jul 2016 14:23:07 +0000 (17:23 +0300)]
net/mlx5: Properly remove all steering objects
Instead of explicitly cleaning up the well known parts of the steering
tree, we use the generic tree structure to traverse for cleanup.
No functional changes.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Mon, 4 Jul 2016 14:23:06 +0000 (17:23 +0300)]
net/mlx5: Introduce mlx5_flow_steering structure
Instead of having all steering private name spaces and
steering module fields flat in mlx5_core_priv, we wrap
them in mlx5_flow_steering for better modularity and
API exposure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Mon, 4 Jul 2016 14:23:05 +0000 (17:23 +0300)]
net/mlx5: Refactor mlx5_add_flow_rule
Reduce the set of arguments passed to mlx5_add_flow_rule
by introducing flow_spec structure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8067302973a1 ("net-next: mediatek: add support for IRQ grouping")
adds handling for irq 1 and 2 to the uninit function but did not remove
irq 0 which is not used since irq grouping was introduced. Fix this by
removing the superfluous call to free_irq().
Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: John Crispin <john@phrozen.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit f786f3564c4f02d5026 ("net: ethernet: lpc_eth: use phydev
from struct net_device") the 'pldat' variable became unused, so
just remove it.
Reported-by: Olof's autobuilder <build@lixom.net> Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 Jul 2016 06:33:59 +0000 (23:33 -0700)]
Merge tag 'batadv-next-for-davem-20160704' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature patchset includes the following changes:
- Cleanup work by Markus Pargmann and Sven Eckelmann (six patches)
- Initial Netlink support by Matthias Schiffer (two patches)
- Throughput Meter implementation by Antonio Quartulli, a kernel-space
traffic generator to estimate link speeds. This feature is useful on
low-end WiFi APs where running iperf or netperf from userspace
gives wrong results due to heavy userspace/kernelspace overhead.
(two patches)
- API clean-up work by Antonio Quartulli (one patch)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth: delete napi struct when removing a qeth device
A qeth_card contains a napi_struct linked to the net_device during
device probing. This struct must be deleted when removing the qeth
device, otherwise Panic on oops can occur when qeth devices are
repeatedly removed and added.
Fixes: a1c3ed4c9ca ("qeth: NAPI support for l2 and l3 discipline") Cc: stable@vger.kernel.org # v2.6.37+ Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Tested-by: Alexander Klein <ALKL@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 Jul 2016 01:25:16 +0000 (18:25 -0700)]
Merge branch 'mlxsw-fib-offload'
Jiri Pirko says:
====================
mlxsw: Implement basic FIB offload and router interfaces
Introduce LPM trees management including virtual router management for HW.
Implement basic FIB offloading using switchdev FIB objects. For now only support
local routes and direct routes (next-hop support will be introduced in
a follow-up patchset).
Introduce router interfaces in patches 10-14.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Enable L3 interfaces on top of bridge devices
As with the previously introduced L3 interfaces, listen to 'inetaddr'
notifications sent for bridges devices configured on top of the port
netdevs and create / destroy router interfaces (RIFs) accordingly.
This also includes VLAN devices configured on top of the VLAN-aware
bridge.
The RIFs will be destroyed either when the last IP address is removed or
when the underlying FID is is destroyed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Configure FIDs based on bridge events
Before introducing support for L3 interfaces on top of the VLAN-aware
bridge we need to add some missing infrastructure.
Such an interface can either be the bridge device itself or a VLAN
device on top of it. In the first case the router interface (RIF) is
associated with FID 1, which is created whenever the first port netdev
joins the bridge. We currently assume the default PVID is 1 and that
it's already created, as it seems reasonable. This can be extended in
the future.
However, in the second case it's entirely possible we've yet to create a
matching FID. This can happen if the VLAN device was configured before
making any bridge port member in the VLAN.
Prevent such ordering problems by using the VLAN device's CHANGEUPPER
event to configure the FID. Make the VLAN device hold a reference to the
FID and prevent it from being destroyed even if none of the port netdevs
is using it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commit deprecated the vFIDs used to get traffic to the CPU
('port_vfids'). Thus, we now use the vFIDs as god intended and the
artificial split is no longer needed.
Rename functions and variables to reflect that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Introduce support for router interfaces
Up until now we only supported bridged interfaces. Packets ingressing
through the switch ports were either classified to FIDs (in the case of
the VLAN-aware bridge) or vFIDs (in the case of VLAN-unaware bridges).
The packets were then forwarded according to the FDB. Routing was done
entirely in slowpath, by splitting the vFID range in two and using the
lower 0.5K vFIDs as dummy bridges that simply flooded all incoming
traffic to the CPU.
Instead, allow packets to be routed in the device by creating router
interfaces (RIFs) that will direct them to the router block.
Specifically, the RIFs introduced here are Sub-port RIFs used for VLAN
devices and port netdevs. Packets ingressing from the {Port / LAG ID, VID}
with which the RIF was programmed with will be assigned to a special
kind of FIDs called rFIDs and from there directed to the router.
Create a RIF whenever the first IPv4 address was programmed on a VLAN /
LAG / port netdev. Destroy it upon removal of the last IPv4 address.
Receive these notifications by registering for the 'inetaddr'
notification chain. A non-zero (10) priority is used for the
notification block, so that RIFs will be created before routes are
offloaded via FIB code.
Note that another trigger for RIF destruction are CHANGEUPPER
notifications causing the underlying FID's reference count to go down to
zero. This can happen, for example, when a VLAN netdev with an IP address
is put under bridge. While this configuration doesn't make sense it does
cause the device and the kernel to get out of sync when the netdev is
unbridged. We intend to address this in the future, hopefully in current
cycle.
Finally, Remove the lower 0.5K vFIDs, as they are deprecated by the RIFs,
which will trap packets according to their DIP.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Edit RIF properties based on netdev events
We are just about to introduce router interfaces (RIFs), but before that
we need to be able update the device with the correct RIF attributes
whenever they change for the netdev the RIF is backing. Two such
attributes are MTU and MAC.
The MAC is used both to set the source MAC of packets egressing from the
RIF and also to program an FDB rule that will direct packets to the
router block.
Use the existing netdevice notification block and respond to CHANGEADDR
and CHANGEMTU accordingly. Store both attributes in the RIF struct
in case we need to revert to old attributes following a failed update.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Add couple of lower device helper functions
Add functions that iterate over lower devices and find port device.
As a dependency add netdev_for_each_all_lower_dev and
netdev_for_each_all_lower_dev_rcu macro with
netdev_all_lower_get_next and netdev_all_lower_get_next_rcu shelpers.
Also, add functions to return mlxsw struct according to lower device
found and mlxsw_port struct with a reference to lower device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ipv4 FIB entries addition and removal. Initially, we support
local and broadcast routes using "ip2me" trap action.
Also, unicast routes without nexthop are supported using "local" action.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual router is a construct used inside HW. In this implementation
we map kernel tables to virtual routers one to one. Introduce management
logic to create virtual routers when needed and destroy in case they are
no longer in use. According to that, call into LPM tree management.
Each virtual router is always bound to one LPM tree.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_router: Implement LPM trees management
Introduce basic LPM tree management allowing to share the trees in
between tables if the used prefixes in the tables are the same.
Build the tree structure according to the used prefixes. Although it is
not optimal for many use cases, this initial implementation does only
simple linear left-tree. More advanced structures will be introduced
later on, possibly including mechanisms to change trees on the fly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shadow FIB is needed in order to hold additional information for FIB
entries and keep track of used prefixes. That is needed for the LPM tree
construction to be introduced later on in this set.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Mon, 4 Jul 2016 05:53:38 +0000 (13:53 +0800)]
tun: fix build warnings
Stephen Rothwell reports a build warnings(powerpc ppc64_defconfig)
drivers/net/tun.c: In function 'tun_do_read.part.5':
/home/sfr/next/next/drivers/net/tun.c:1491:6: warning: 'err' may be
used uninitialized in this function [-Wmaybe-uninitialized]
int err;
This is because tun_ring_recv() may return an uninitialized err, fix this.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 Jul 2016 23:15:32 +0000 (16:15 -0700)]
Merge branch 'liquidio-next'
Raghu Vatsavayi says:
====================
liquidio updates and bug fixes
Following V2 patchset contains updates and bug fixes for
liquidio driver. This patchset also has changes that you
suggested in vxlan code. Please apply the patches in following
order as some of the patches depend on earlier patches in the
series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log