Vivien Didelot [Mon, 20 Apr 2015 21:43:26 +0000 (17:43 -0400)]
net: dsa: mv88e6xxx: use PORT_DEFAULT_VLAN
Minor, use the explicit PORT_DEFAULT_VLAN define instead of 0x07.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Mon, 20 Apr 2015 21:19:23 +0000 (17:19 -0400)]
net: dsa: mv88e6xxx: fix setup of port control 1
mv88e6xxx_setup_port_common was writing to PORT_DEFAULT_VLAN (port
offset 0x07) instead of PORT_CONTROL_1 (port offset 0x05).
Fixes: cca8b1337541 ("net: dsa: Use mnemonics rather than register numbers") Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set addresses bug "Bug 95171 - "hw csum failure" message
flood for ppp tunnel since upgrade to 3.16". The problem is that pppoe
is being used over UDP with UDP checksusm enabled. On receive
checksum conversion turns checksum-unnecessary in checksum-
complete. The PPP receive functions do not properly pull
the checksum over its headers, so that when an encapsulated
checksums is considered the checksum-complete value is incorrect.
This patch adds skb_checksum_complete_unset which can be called
in the receive path in lieu of pulling checksum complete in
layer. This is useful when the packet is being modified (e.g.
decompressed) and the checksum-complete value is no longer
relevant.
In the ppp_receive_frame we call skb_checksum_complete_unset to toss
out checksum-complete. This should eliminate the reported messages.
Alternatively, we could add skb_postpull_rcsum and probably
special case handling for VJ compression if maintaining the
checksum-complete is needed (not clear to me this is worth the
effort).
I haven't tested this since setting up the failure scenario doesn't
seem trivial to configure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Mon, 20 Apr 2015 21:10:05 +0000 (14:10 -0700)]
ppp: call skb_checksum_complete_unset in ppp_receive_frame
Call checksum_complete_unset in PPP receive to discard checksum-complete
value. PPP does not pull checksum for headers and also modifies packet
as in VJ compression.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Mon, 20 Apr 2015 21:10:04 +0000 (14:10 -0700)]
net: add skb_checksum_complete_unset
This function changes ip_summed to CHECKSUM_NONE if CHECKSUM_COMPLETE
is set. This is called to discard checksum-complete when packet
is being modified and checksum is not pulled for headers in a layer.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A pppoe session is identified by its session ID and MAC address.
Currently pppoe does not check if the received pkg has the correct
MAC address. This is a problem when the eth I/F is in promisc mode
as then any DST MAC address is accepted.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Forwarded frames should not have a socket attached. Especially
tw sockets will lead to panics later-on in the stack.
This was observed with TPROXY assigning a tw socket and broken
policy routing (misconfigured). As a result frame enters
forwarding path instead of input. We cannot solve this in
TPROXY as it cannot know that policy routing is broken.
v2:
Remove useless comment
Signed-off-by: Sebastian Poehn <sebastian.poehn@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Fix verifier memory corruption and other bugs in BPF layer, from
Alexei Starovoitov.
2) Add a conservative fix for doing BPF properly in the BPF classifier
of the packet scheduler on ingress. Also from Alexei.
3) The SKB scrubber should not clear out the packet MARK and security
label, from Herbert Xu.
4) Fix oops on rmmod in stmmac driver, from Bryan O'Donoghue.
5) Pause handling is not correct in the stmmac driver because it
doesn't take into consideration the RX and TX fifo sizes. From
Vince Bridgers.
6) Failure path missing unlock in FOU driver, from Wang Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
net: dsa: use DEVICE_ATTR_RW to declare temp1_max
netns: remove BUG_ONs from net_generic()
IB/ipoib: Fix ndo_get_iflink
sfc: Fix memcpy() with const destination compiler warning.
altera tse: Fix network-delays and -retransmissions after high throughput.
net: remove unused 'dev' argument from netif_needs_gso()
act_mirred: Fix bogus header when redirecting from VLAN
inet_diag: fix access to tcp cc information
tcp: tcp_get_info() should fetch socket fields once
net: dsa: mv88e6xxx: Add missing initialization in mv88e6xxx_set_port_state()
skbuff: Do not scrub skb mark within the same name space
Revert "net: Reset secmark when scrubbing packet"
bpf: fix two bugs in verification logic when accessing 'ctx' pointer
bpf: fix bpf helpers to use skb->mac_header relative offsets
stmmac: Configure Flow Control to work correctly based on rxfifo size
stmmac: Enable unicast pause frame detect in GMAC Register 6
stmmac: Read tx-fifo-depth and rx-fifo-depth from the devicetree
stmmac: Add defines and documentation for enabling flow control
stmmac: Add properties for transmit and receive fifo sizes
stmmac: fix oops on rmmod after assigning ip addr
...
Pull sparc updates from David Miller:
"The PowerPC folks have a really nice scalable IOMMU pool allocator
that we wanted to make use of for sparc. So here we have a series
that abstracts out their code into a common layer that anyone can make
use of.
Sparc is converted, and the PowerPC folks have reviewed and ACK'd this
series and plan to convert PowerPC over as well"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
sparc: Break up monolithic iommu table/lock into finer graularity pools and lock
Pull arch/tile updates from Chris Metcalf:
"These are mostly nohz_full changes, plus a smattering of minor fixes
(notably a couple for ftrace)"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: nohz: warn if nohz_full uses hypervisor shared cores
tile: ftrace: fix function_graph tracer issues
tile: map data region shadow of kernel as R/W
tile: support CONTEXT_TRACKING and thus NOHZ_FULL
tile: support arch_irq_work_raise
arch: tile: fix null pointer dereference on pt_regs pointer
tile/elf: reorganize notify_exec()
tile: use si_int instead of si_ptr for compat_siginfo
Vivien Didelot [Fri, 17 Apr 2015 19:12:25 +0000 (15:12 -0400)]
net: dsa: use DEVICE_ATTR_RW to declare temp1_max
Since commit da4759c (sysfs: Use only return value from is_visible for
the file mode), it is possible to reduce the permissions of a file.
So declare temp1_max with the DEVICE_ATTR_RW macro and remove the write
permission in dsa_hwmon_attrs_visible if set_temp_limit isn't provided.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
On 04/14/2015 08:37 PM, David Miller wrote:
> That BUG_ON() was added 7 years ago, and I don't remember it ever
> triggering or helping us diagnose something, so just remove it and
> keep the function inlined.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com> CC: Eric W. Biederman <ebiederm@xmission.com> CC: David S. Miller <davem@davemloft.net> CC: Jan Engelhardt <jengelh@medozas.de> CC: Jiri Pirko <jpirko@redhat.com> CC: linux-kernel@vger.kernel.org CC: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, iflink of the parent interface was always accessed, even
when interface didn't have a parent and hence we crashed there.
Handle the interface types properly: for a child interface, return
the ifindex of the parent, for parent interface, return its ifindex.
For child devices, make sure to set the parent pointer prior to
invoking register_netdevice(), this allows the new ndo to be called
by the stack immediately after the child device is registered.
Fixes: 5aa7add8f14b ('infiniband/ipoib: implement ndo_get_iflink') Reported-by: Honggang Li <honli@redhat.com> Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: Honggang Li <honli@redhat.com> Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>+ Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 17 Apr 2015 19:15:40 +0000 (15:15 -0400)]
sfc: Fix memcpy() with const destination compiler warning.
drivers/net/ethernet/sfc/selftest.c: In function ‘efx_iterate_state’:
drivers/net/ethernet/sfc/selftest.c:388:9: warning: passing argument 1 of ‘memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers]
This is because the msg[] member of struct efx_loopback_payload
is marked as 'const'. Remove that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Oetken [Thu, 16 Apr 2015 21:48:08 +0000 (23:48 +0200)]
altera tse: Fix network-delays and -retransmissions after high throughput.
Fix bug which occurs when more than <limit> packets are available during
napi-poll, leading to "delays" and retransmissions on the network.
Check for (count < limit) before checking the get_rx_status in tse_rx-function.
Function get_rx_status is reading from the response-fifo.
If there is currently a response in the fifo,
reading the last byte of the response pops the value from the fifo.
If the limit is checked as second condition
and the limit is reached the fifo is popped but the packet is not processed.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block core fix from Jens Axboe:
"A commit in the previous pull request introduce a regression. So far
only observed on qemu-sparc64, but it's a general bug. Please pull
this single fix to rectify that, thanks"
[ And it turns out that it's been seen outside of that qemu-sparc64
case, and is easy to trigger with small number of CPUs and blk-mq
enabled by default - Linus ]
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: fix iteration of busy bitmap
Merge tag 'acpica-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPICA updates from Rafael Wysocki:
"This updates the kernel's ACPICA code to upstream revision 20150410
and adds a fix for a GPE handling regression introduced during the
3.19 cycle on top of that.
Included are two stable-candidate bug fixes (one of them fixing a 3.16
regression), multiple other fixes and a bunch of cleanups.
Specifics:
- Fix for a GPE handling regression on Dell Latitude D600 that caused
GPE signaling to stop working on that machine, which appears to be
due to a hardware glitch, but it used to work and it can be made
work again in a relativly straightforward way (Rafael J Wysocki).
- Fix for a mutex unlock regression related to the handling of ACPI
tables introduced during the 3.16 development cycle (Octavian
Purdila).
- _REV modification to always return 2 which has been done by all
versions of Windows since NT and the firmware people started to use
it to distinguish between OSes in their AML and do some silly and
wrong things on that basis (Bob Moore).
- Fixes and cleanups related to the acpi_physicall_address data type
including one stable-candidate fix for an issue occasionally
occuring on 64-bit machines running 32-bit kernels where using
offsets provided by the firmware may lead to address overflows (Lv
Zheng).
- External() opcode support infrastructure needed for recompiling
disassembled ACPI tables in some cases including interpreter
modification to ignore that opcode (Bob Moore).
- Support for the "Windows 2015" string in _OSI (Bob Moore).
- GPE debug interface change to return values read from hardware
registers (Lv Zheng).
- Removal of the __DATE__ macro usage in tools (Rasmus Villemoes).
- Assorted minor fixes and cleanups (Lv Zheng, Rickard Strandqvist,
Bob Moore)"
* tag 'acpica-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
ACPICA: Store GPE register enable masks upfront
ACPICA: Update version to 20150410.
ACPICA: Fix a couple issues with the local printf module.
ACPICA: Disassembler: Some cleanup of the table dump module.
ACPICA: iASL: Add support for MSDM ACPI table.
ACPICA: Update for SLIC ACPI table.
ACPICA: Add "//" before ascii output of buffers.
ACPICA: Remove unused internal AML opcode.
ACPICA: Permanently set _REV to the value '2'.
ACPICA: Add "Windows 2015" string to _OSI support.
ACPICA: Add infrastructure for External() opcode.
ACPICA: iASL: Enhancement for constant folding.
ACPICA: iASL/Disassembler: Add option to assume table contains valid AML.
ACPICA: Update AML Debugger global variables.
ACPICA: Update Resource descriptor dump module.
ACPICA: Fix a sscanf format string.
ACPICA: Casting changes around acpi_physical_address/acpi_size.
ACPICA: Resources: Correct conditional compilation definitions.
ACPICA: Utilities: Correct conditional compilation definitions.
ACPICA: Tables: Move an iasl specific table function to iasl source file.
...
Chris Metcalf [Mon, 30 Mar 2015 20:33:00 +0000 (16:33 -0400)]
tile: nohz: warn if nohz_full uses hypervisor shared cores
The "hypervisor shared" cores are ones that the Tilera hypervisor
uses to receive interrupts to manage hypervisor-owned devices.
It's a bad idea to try to use those cores with nohz_full, since
they will get interrupted unpredictably -- and invisibly to Linux
tracing tools, since the interrupts are delivered at a higher
privilege level to the Tilera hypervisor.
Generate a clear warning at boot up that this doesn't end well
for the nohz_full cores in question.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Tony Lu [Fri, 27 Mar 2015 18:46:38 +0000 (14:46 -0400)]
tile: ftrace: fix function_graph tracer issues
- Add support for ARCH_SUPPORTS_FTRACE_OPS
- Replace the instruction in ftrace_call with the bundle {move r10, lr;
jal ftrace_stub}, so that the lr contains the right value after returning
from ftrace_stub. An alternative fix might be to leave the instruction
in ftrace_call alone when it is being updated with ftrace_stub.
Signed-off-by: Tony Lu <zlu@ezchip.com> Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Chris Metcalf [Fri, 27 Mar 2015 18:35:31 +0000 (14:35 -0400)]
tile: map data region shadow of kernel as R/W
This is necessary for things like reading /proc/kcore, doing ftrace,
etc. It happens by default when using huge pages to map the kernel
data, but not when using small pages.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Chris Metcalf [Mon, 23 Mar 2015 18:23:58 +0000 (14:23 -0400)]
tile: support CONTEXT_TRACKING and thus NOHZ_FULL
Add the TIF_NOHZ flag appropriately.
Add call to user_exit() on entry to do_work_pending() and on entry
to syscalls via do_syscall_trace_enter(), and also the top of
do_syscall_trace_exit() just because it's done in x86.
Add call to user_enter() at the bottom of do_work_pending() once we
have no more work to do before returning to userspace.
Wrap all the trap code in exception_enter() / exception_exit().
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Johannes Berg [Fri, 17 Apr 2015 13:45:04 +0000 (15:45 +0200)]
net: remove unused 'dev' argument from netif_needs_gso()
In commit 04ffcb255f22 ("net: Add ndo_gso_check") Tom originally
added the 'dev' argument to be able to call ndo_gso_check().
Then later, when generalizing this in commit 5f35227ea34b
("net: Generalize ndo_gso_check to ndo_features_check")
Jesse removed the call to ndo_gso_check() in netif_needs_gso()
by calling the new ndo_features_check() in a different place.
This made the 'dev' argument unused.
Remove the unused argument and go back to the code as before.
Cc: Tom Herbert <therbert@google.com> Cc: Jesse Gross <jesse@nicira.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 17 Apr 2015 05:32:09 +0000 (13:32 +0800)]
act_mirred: Fix bogus header when redirecting from VLAN
When you redirect a VLAN device to any device, you end up with
crap in af_packet on the xmit path because hard_header_len is
not equal to skb->mac_len. So the redirected packet contains
four extra bytes at the start which then gets interpreted as
part of the MAC address.
This patch fixes this by only pushing skb->mac_len. We also
need to fix ifb because it tries to undo the pushing done by
act_mirred.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 17 Apr 2015 01:10:35 +0000 (18:10 -0700)]
inet_diag: fix access to tcp cc information
Two different problems are fixed here :
1) inet_sk_diag_fill() might be called without socket lock held.
icsk->icsk_ca_ops can change under us and module be unloaded.
-> Access to freed memory.
Fix this using rcu_read_lock() to prevent module unload.
2) Some TCP Congestion Control modules provide information
but again this is not safe against icsk->icsk_ca_ops
change and nla_put() errors were ignored. Some sockets
could not get the additional info if skb was almost full.
Fix this by returning a status from get_info() handlers and
using rcu protection as well.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 16 Apr 2015 23:12:28 +0000 (16:12 -0700)]
tcp: tcp_get_info() should fetch socket fields once
tcp_get_info() can be called without holding socket lock,
so any socket fields can change under us.
Use READ_ONCE() to fetch sk_pacing_rate and sk_max_pacing_rate
Fixes: 977cb0ecf82e ("tcp: add pacing_rate information into tcp_info") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Metcalf [Mon, 23 Mar 2015 15:21:23 +0000 (11:21 -0400)]
tile: support arch_irq_work_raise
Tile includes a hypervisor hook to deliver messages to arbitrary
tiles, so we can use that to raise an interrupt as soon as
possible on our own core. Unfortunately the Tilera hypervisor
disabled that support on principle in previous releases, but
it will be available in MDE 4.3.4 and later.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Colin Ian King [Mon, 16 Mar 2015 20:14:02 +0000 (16:14 -0400)]
arch: tile: fix null pointer dereference on pt_regs pointer
Cppcheck reports the following issue:
[arch/tile/kernel/stack.c:116]: (error) Possible null
pointer dereference: p
In this case, on reporting on an odd fault, p is set to NULL
and immediately afterwords p is dereferenced iff
!kbt->profile is false. Rather than doing this check just
return NULL rather than falling through to the potential
null pointer dereference (since the original intentional
outcome would be to return NULL anyhow) for this odd fault
case.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com> [tweaked lightly]
Davidlohr Bueso [Wed, 25 Feb 2015 21:58:35 +0000 (13:58 -0800)]
tile/elf: reorganize notify_exec()
In the future mm->exe_file will be done without mmap_sem
serialization, thus isolate and reorganize the tile elf
code to make the transition easier. Good users will, make
use of the more standard get_mm_exe_file(), requiring only
holding the mmap_sem to read the value, and relying on reference
counting to make sure that the exe file won't dissappear
underneath us.
The visible effects of this patch are:
o We now take and drop the mmap_sem more often. Instead of
just in arch_setup_additional_pages(), we also do it in:
1) get_mm_exe_file()
2) to get the mm->vm_file and notify the simulator.
[Note that 1) will disappear once we change the locking
rules for exe_file.]
o We avoid getting a free page and doing d_path() while
holding the mmap_sem. This requires reordering the checks.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Chris Metcalf [Mon, 16 Mar 2015 19:04:05 +0000 (15:04 -0400)]
tile: use si_int instead of si_ptr for compat_siginfo
To be compatible with the generic get_compat_sigevent(), the
copy_siginfo_to_user32() and thus copy_siginfo_from_user32()
have to use si_int instead of si_ptr. Using si_ptr means that
for the case of ILP32 compat code running in big-endian mode,
we would end up copying the high 32 bits of the pointer value
into si_int instead of the desired low 32 bits.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com> Cc: Catalin Marinas <catalin.marinas@arm.com>
Commit 889fa31f00b2 was a bit too eager in reducing the loop count,
so we ended up missing queues in some configurations. Ensure that
our division rounds up, so that's not the case.
- more mmap_sem hold time reductions from Davidlohr
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (138 commits)
proc: show locks in /proc/pid/fdinfo/X
docs: add missing and new /proc/PID/status file entries, fix typos
drivers/rtc/rtc-at91rm9200.c: make IO endian agnostic
Documentation/spi/spidev_test.c: fix warning
drivers/rtc/rtc-s5m.c: allow usage on device type different than main MFD type
.gitignore: ignore *.tar
MAINTAINERS: add Mediatek SoC mailing list
tomoyo: reduce mmap_sem hold for mm->exe_file
powerpc/oprofile: reduce mmap_sem hold for exe_file
oprofile: reduce mmap_sem hold for mm->exe_file
mips: ip32: add platform data hooks to use DS1685 driver
lib/Kconfig: fix up HAVE_ARCH_BITREVERSE help text
x86: switch to using asm-generic for seccomp.h
sparc: switch to using asm-generic for seccomp.h
powerpc: switch to using asm-generic for seccomp.h
parisc: switch to using asm-generic for seccomp.h
mips: switch to using asm-generic for seccomp.h
microblaze: use asm-generic for seccomp.h
arm: use asm-generic for seccomp.h
seccomp: allow COMPAT sigreturn overrides
...
Let's show locks which are associated with a file descriptor in
its fdinfo file.
Currently we don't have a reliable way to determine who holds a lock. We
can find some information in /proc/locks, but PID which is reported there
can be wrong. For example, a process takes a lock, then forks a child and
dies. In this case /proc/locks contains the parent pid, which can be
reused by another process.
Andrew Morton [Thu, 16 Apr 2015 19:49:29 +0000 (12:49 -0700)]
Documentation/spi/spidev_test.c: fix warning
Documentation/spi/spidev_test.c:83:5: warning: no previous prototype for 'unespcape' [-Wmissing-prototypes]
fix spelling too.
Acked-by: Mark Brown <broonie@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/rtc/rtc-s5m.c: allow usage on device type different than main MFD type
The RTC driver supports two flavors of S5M devices: S5M8767-like and
S2MPS14-like.
On S2MPS13 and S2MPS14 devices the RTC module is the same so we want to
re-use the existing support of S2MPS14. However device type was passed
from parent MFD driver in platform data structure. This way for the
S2MPS13 device the main MFD driver passed device type of 'S2MPS13X'.
Instead decouple detecting of device type between main MFD and RTC driver.
This allows adding support for other S2MPS14 variations (like S2MPS11 and
S2MPS13) easily by adding to mfd/sec-core.c:
# Untracked files:
# (use "git add <file>..." to include in what will be committed)
#
# linux-4.0.0-rc3-next-20150313-150225--x86.tar
This patch makes git ignore *.tar files.
Running 'git ls-files -i --exclude-standard' does not show any
tar files excluded from tracking after the change.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com> Cc: Michal Marek <mmarek@suse.cz> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Boaz Harrosh <boaz@plexistor.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Benjamin Romer <benjamin.romer@unisys.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mm->exe_file is currently serialized with mmap_sem (shared) in order
to both safely (1) read the file and (2) compute the realpath by calling
tomoyo_realpath_from_path, making it an absolute overkill. Good users
will, on the other hand, make use of the more standard get_mm_exe_file(),
requiring only holding the mmap_sem to read the value, and relying on
reference
powerpc/oprofile: reduce mmap_sem hold for exe_file
In the future mm->exe_file will be done without mmap_sem serialization,
thus isolate and reorganize the related code to make the transition
easier. Good users will, make use of the more standard get_mm_exe_file(),
requiring only holding the mmap_sem to read the value, and relying on
reference counting to make sure that the exe file won't dissappear
underneath us while getting the dcookie.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Robert Richter <rric@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sync_buffer() needs the mmap_sem for two distinct operations, both only
occurring upon user context switch handling:
1) Dealing with the exe_file.
2) Adding the dcookie data as we need to lookup the vma that
backs it. This is done via add_sample() and add_data().
This patch isolates 1), for it will no longer need the mmap_sem for
serialization. However, for now, make of the more standard
get_mm_exe_file(), requiring only holding the mmap_sem to read the value,
and relying on reference counting to make sure that the exe file won't
dissappear underneath us while doing the get dcookie.
As a consequence, for 2) we move the mmap_sem locking into where we really
need it, in lookup_dcookie(). The benefits are twofold: reduce mmap_sem
hold times, and cleaner code.
[akpm@linux-foundation.org: export get_mm_exe_file for arch/x86/oprofile/oprofile.ko] Signed-off-by: Davidlohr Bueso <dbueso@suse.de> Cc: Robert Richter <rric@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mips: ip32: add platform data hooks to use DS1685 driver
This modifies the IP32 (SGI O2) platform and reset code to utilize the new
rtc-ds1685 driver. The old mc146818rtc.h header is removed and ip32_defconfig
is updated as well.
Andrew Morton [Thu, 16 Apr 2015 19:49:07 +0000 (12:49 -0700)]
lib/Kconfig: fix up HAVE_ARCH_BITREVERSE help text
Cc: Yalin Wang <yalin.wang@sonymobile.com> Cc: Russell King <linux@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to using the newly created asm-generic/seccomp.h for the seccomp
strict mode syscall definitions. The obsolete sigreturn syscall override
is retained in 32-bit mode, and the ia32 syscall overrides are used in
the compat case. Remaining definitions were identical.
Signed-off-by: Kees Cook <keescook@chromium.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to using the newly created asm-generic/seccomp.h for the seccomp
strict mode syscall definitions. The obsolete sigreturn in COMPAT mode
is retained as an override. Remaining definitions are identical. Also
corrected missing #define for header reinclusion protection.
Signed-off-by: Kees Cook <keescook@chromium.org> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
powerpc: switch to using asm-generic for seccomp.h
Switch to using the newly created asm-generic/seccomp.h for the seccomp
strict mode syscall definitions. The obsolete sigreturn in COMPAT mode is
retained as an override. Remaining definitions are identical, though they
incorrectly appeared in uapi, which has been corrected.
Signed-off-by: Kees Cook <keescook@chromium.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to using the newly created asm-generic/seccomp.h for the seccomp
strict mode syscall definitions. COMPAT definitions retain their
overrides and the remaining definitions were identical.
Switch to using the newly created asm-generic/seccomp.h for the seccomp
strict mode syscall definitions. Since microblaze is 32-bit, the COMPAT
seccomp defines are unused and can be dropped. The obsolete sigreturn
for seccomp strict mode is retained as an override. Remaining definitions
are identical.
Signed-off-by: Kees Cook <keescook@chromium.org> Cc: Michal Simek <monstr@monstr.eu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to using the newly created asm-generic/seccomp.h for the seccomp
strict mode syscall definitions. Definitions were identical.
Signed-off-by: Kees Cook <keescook@chromium.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Laura Abbott <lauraa@codeaurora.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Simek [Thu, 16 Apr 2015 19:48:38 +0000 (12:48 -0700)]
include/linux/kconfig.h: ese macros which are already defined
It is better to use macros which are already available because then there
is just one location which needs to be change.
[akpm@linux-foundation.org: move IS_ENABLED definition to after the IS_BUILTIN and IS_MODULE definitions] Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Thu, 16 Apr 2015 19:48:35 +0000 (12:48 -0700)]
memstick: mspro_block: add missing curly braces
Using the indenting we can see the curly braces were obviously intended.
This is a static checker fix, but my guess is that we don't read enough
bytes, because we don't calculate "t_len" correctly.
Fixes: f1d82698029b ('memstick: use fully asynchronous request processing') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Alex Dubov <oakad@yahoo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kernel/sysctl.c: detect overflows when converting to int
When converting unsigned long to int overflows may occur. These currently
are not detected when writing to the sysctl file system.
E.g. on a system where int has 32 bits and long has 64 bits
echo 0x800001234 > /proc/sys/kernel/threads-max
has the same effect as
echo 0x1234 > /proc/sys/kernel/threads-max
The patch adds the missing check in do_proc_dointvec_conv.
With the patch an overflow will result in an error EINVAL when writing to
the the sysctl file system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpumask: don't perform while loop in cpumask_next_and()
cpumask_next_and() is looking for cpumask_next() in src1 in a loop and
tests if found cpu is also present in src2. remove that loop, perform
cpumask_and() of src1 and src2 first and use that new mask to find
cpumask_next().
Apart from removing while loop, ./bloat-o-meter on x86_64 shows
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8 (-8)
function old new delta
cpumask_next_and 62 54 -8
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Tejun Heo <tj@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Amir Vadai <amirv@mellanox.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
prctl: avoid using mmap_sem for exe_file serialization
Oleg cleverly suggested using xchg() to set the new mm->exe_file instead
of calling set_mm_exe_file() which requires some form of serialization --
mmap_sem in this case. For archs that do not have atomic rmw instructions
we still fallback to a spinlock alternative, so this should always be
safe. As such, we only need the mmap_sem for looking up the backing
vm_file, which can be done sharing the lock. Naturally, this means we
need to manually deal with both the new and old file reference counting,
and we need not worry about the MMF_EXE_FILE_CHANGED bits, which can
probably be deleted in the future anyway.
This patch removes mm->mmap_sem from mm->exe_file read side.
Also it kills dup_mm_exe_file() and moves exe_file duplication into
dup_mmap() where both mmap_sems are locked.
[akpm@linux-foundation.org: fix comment typo] Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Oleg Nesterov <oleg@redhat.com> Cc: "Paul E. McKenney" <paulmck@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PAGE_SIZE is not guaranteed to be equal to or less than 8 times the
THREAD_SIZE.
E.g. architecture hexagon may have page size 1M and thread size 4096.
This would lead to a division by zero in the calculation of max_threads.
With 32-bit calculation there is no solution which delivers valid results
for all possible combinations of the parameters. The code is only called
once. Hence a 64-bit calculation can be used as solution.
[akpm@linux-foundation.org: use clamp_t(), per Oleg] Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jean Delvare [Thu, 16 Apr 2015 19:47:41 +0000 (12:47 -0700)]
fork_init: update max_threads comment
The comment explaining what value max_threads is set to is outdated. The
maximum memory consumption ratio for thread structures was 1/2 until
February 2002, then it was briefly changed to 1/16 before being set to 1/8
which we still use today. The comment was never updated to reflect that
change, it's about time.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Thu, 16 Apr 2015 19:47:38 +0000 (12:47 -0700)]
fork: report pid reservation failure properly
copy_process will report any failure in alloc_pid as ENOMEM currently
which is misleading because the pid allocation might fail not only when
the memory is short but also when the pid space is consumed already.
The current man page even mentions this case:
: EAGAIN
:
: A system-imposed limit on the number of threads was encountered.
: There are a number of limits that may trigger this error: the
: RLIMIT_NPROC soft resource limit (set via setrlimit(2)), which
: limits the number of processes and threads for a real user ID, was
: reached; the kernel's system-wide limit on the number of processes
: and threads, /proc/sys/kernel/threads-max, was reached (see
: proc(5)); or the maximum number of PIDs, /proc/sys/kernel/pid_max,
: was reached (see proc(5)).
so the current behavior is also incorrect wrt. documentation. POSIX man
page also suggest returing EAGAIN when the process count limit is reached.
This patch simply propagates error code from alloc_pid and makes sure we
return -EAGAIN due to reservation failure. This will make behavior of
fork closer to both our documentation and POSIX.
alloc_pid might alsoo fail when the reaper in the pid namespace is dead
(the namespace basically disallows all new processes) and there is no
good error code which would match documented ones. We have traditionally
returned ENOMEM for this case which is misleading as well but as per
Eric W. Biederman this behavior is documented in man pid_namespaces(7)
: If the "init" process of a PID namespace terminates, the kernel
: terminates all of the processes in the namespace via a SIGKILL signal.
: This behavior reflects the fact that the "init" process is essential for
: the correct operation of a PID namespace. In this case, a subsequent
: fork(2) into this PID namespace will fail with the error ENOMEM; it is
: not possible to create a new processes in a PID namespace whose "init"
: process has terminated.
and introducing a new error code would be too risky so let's stick to
ENOMEM for this case.
Signed-off-by: Michal Hocko <mhocko@suse.cz> Cc: Oleg Nesterov <oleg@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vladimir Davydov [Thu, 16 Apr 2015 19:47:35 +0000 (12:47 -0700)]
signal: remove warning about using SI_TKILL in rt_[tg]sigqueueinfo
Sending SI_TKILL from rt_[tg]sigqueueinfo was deprecated, so now we issue
a warning on the first attempt of doing it. We use WARN_ON_ONCE, which is
not informative and, what is worse, taints the kernel, making the trinity
syscall fuzzer complain false-positively from time to time.
It does not look like we need this warning at all, because the behaviour
changed quite a long time ago (2.6.39), and if an application relies on
the old API, it gets EPERM anyway and can issue a warning by itself.
So let us zap the warning in kernel.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Richard Weinberger <richard@nod.at> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ptrace: ptrace_detach() can no longer race with SIGKILL
ptrace_detach() re-checks ->ptrace under tasklist lock and calls
release_task() if __ptrace_detach() returns true. This was needed because
the __TASK_TRACED tracee could be killed/untraced, and it could even pass
exit_notify() before we take tasklist_lock.
But this is no longer possible after 9899d11f6544 "ptrace: ensure
arch_ptrace/ptrace_request can never race with SIGKILL". We can turn
these checks into WARN_ON() and remove release_task().
While at it, document the setting of child->exit_code.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Pavel Labath <labath@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ptrace: fix race between ptrace_resume() and wait_task_stopped()
ptrace_resume() is called when the tracee is still __TASK_TRACED. We set
tracee->exit_code and then wake_up_state() changes tracee->state. If the
tracer's sub-thread does wait() in between, task_stopped_code(ptrace => T)
wrongly looks like another report from tracee.
This confuses debugger, and since wait_task_stopped() clears ->exit_code
the tracee can miss a signal.
Note for stable: the bug is very old, but without 9899d11f6544 "ptrace:
ensure arch_ptrace/ptrace_request can never race with SIGKILL" the fix
should use lock_task_sighand(child).
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Pavel Labath <labath@google.com> Tested-by: Pavel Labath <labath@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Hebb [Thu, 16 Apr 2015 19:47:18 +0000 (12:47 -0700)]
hfsplus: don't store special "osx" xattr prefix on-disk
On Mac OS X, HFS+ extended attributes are not namespaced. Since we want
to be compatible with OS X filesystems and yet still support the Linux
namespacing system, the hfsplus driver implements a special "osx"
namespace that is reported for any attribute that is not namespaced
on-disk. However, the current code for getting and setting these
unprefixed attributes is broken.
hfsplus_osx_setattr() and hfsplus_osx_getattr() are passed names that have
already had their "osx." prefixes stripped by the generic functions. The
functions first, quite correctly, check those names to make sure that they
aren't prefixed with a known namespace, which would allow namespace access
restrictions to be bypassed. However, the functions then prepend "osx."
to the name they're given before passing it on to hfsplus_getattr() and
hfsplus_setattr(). Not only does this cause the "osx." prefix to be
stored on-disk, defeating its purpose, it also breaks the check for the
special "com.apple.FinderInfo" attribute, which is reported for all files,
and as a consequence makes some userspace applications (e.g. GNU patch)
fail even when extended attributes are not otherwise in use.
There are five commits which have touched this particular code:
127e5f5ae51e ("hfsplus: rework functionality of getting, setting and deleting of extended attributes") b168fff72109 ("hfsplus: use xattr handlers for removexattr") bf29e886b242 ("hfsplus: correct usage of HFSPLUS_ATTR_MAX_STRLEN for non-English attributes") fcacbd95e121 ("fs/hfsplus: move xattr_name allocation in hfsplus_getxattr()") ec1bbd346f18 ("fs/hfsplus: move xattr_name allocation in hfsplus_setxattr()")
The first commit creates the functions to begin with. The namespace is
prepended by the original code, which I believe was correct at the time,
since hfsplus_?etattr() stripped the prefix if found. The second commit
removes this behavior from hfsplus_?etattr() and appears to have been
intended to also remove the prefixing from hfsplus_osx_?etattr().
However, what it actually does is remove a necessary strncpy() call
completely, breaking the osx namespace entirely. The third commit re-adds
the strncpy() call as it was originally, but doesn't mention it in its
commit message. The final two commits refactor the code and don't affect
its functionality.
This commit does what b168fff attempted to do (prevent the prefix from
being added), but does it properly, instead of passing in an empty buffer
(which is what b168fff actually did).
Fixes: b168fff72109 ("hfsplus: use xattr handlers for removexattr") Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Cc: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Sergei Antonov <saproj@gmail.com> Cc: Anton Altaparmakov <anton@tuxera.com> Cc: Fabian Frederick <fabf@skynet.be> Cc: Christian Kujau <lists@nerdbynature.de> Cc: Christoph Hellwig <hch@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Viacheslav Dubeyko <slava@dubeyko.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sergei Antonov [Thu, 16 Apr 2015 19:47:15 +0000 (12:47 -0700)]
hfsplus: fix expand when not enough available space
Fix a bug which is reproduced as follows. Create a file:
echo abc > test_file
Try to expand the file beyond available space:
truncate --size=<size exceeding available space> test_file
Since HFS+ does not support file size > allocated size, truncate should
fail. However, it ends successfully. The driver returns success despite
having been unable to allocate the requested space for the file. Also
filesystem check finds an error:
Checking catalog file.
Incorrect size for file test_file
(It should be 469094400 instead of 1000000000)
Add a piece of code analogous to code in the fat driver. Now a proper
error is returned and filesystem remains consistent.
Signed-off-by: Sergei Antonov <saproj@gmail.com> Cc: Vyacheslav Dubeyko <slava@dubeyko.com> Cc: Hin-Tak Leung <htl10@users.sourceforge.net> Reviewed-by: Anton Altaparmakov <anton@tuxera.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@infradead.org> Cc: Sougata Santra <sougata@tuxera.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
nilfs2: use inode_set_flags() in nilfs_set_inode_flags()
Use inode_set_flags() to atomically set i_flags instead of clearing out
the S_IMMUTABLE, S_APPEND, etc. flags and then setting them from the
FS_IMMUTABLE_FL, FS_APPEND_FL flags to avoid a race where an immutable
file has the immutable flag cleared for a brief window of time.
This is a similar fix to commit 5f16f3225b06 ("ext4: atomically set
inode->i_flags in ext4_set_inode_flags()").
nilfs2: put out gfp mask manipulation from nilfs_set_inode_flags()
nilfs_set_inode_flags() function adjusts gfp-mask of inode->i_mapping as
well as i_flags, however, this coupling of operations is not appropriate.
For instance, nilfs_ioctl_setflags(), one of three callers of
nilfs_set_inode_flags(), doesn't need to reinitialize the gfp-mask at all.
In addition, nilfs_new_inode(), another caller of
nilfs_set_inode_flags(), doesn't either because it has already initialized
the gfp-mask.
Only __nilfs_read_inode(), the remaining caller, needs it. So, this moves
the gfp mask manipulation to __nilfs_read_inode() from
nilfs_set_inode_flags().
nilfs2: fix gcc warning at nilfs_checkpoint_is_mounted()
Fix the following build warning:
fs/nilfs2/super.c: In function 'nilfs_checkpoint_is_mounted':
fs/nilfs2/super.c:1023:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (cno < 0 || cno > nilfs->ns_cno)
^
This warning indicates that the comparision "cno < 0" is useless because
variable "cno" has an unsigned integer type "__u64".
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
nilfs2: improve execution time of NILFS_IOCTL_GET_CPINFO ioctl
The older a filesystem gets, the slower lscp command becomes. This is
because nilfs_cpfile_do_get_cpinfo() function meets more hole blocks
as the start offset of valid checkpoint numbers gets bigger.
This reduces the overhead by skipping hole blocks efficiently with
nilfs_mdt_find_block() helper.
A measurement result of this patch is as follows:
Before:
$ time lscp
CNO DATE TIME MODE FLG BLKCNT ICNT 5769303 2015-02-22 19:31:33 cp - 108 1 5769304 2015-02-22 19:38:54 cp - 108 1
real 0m0.182s
user 0m0.003s
sys 0m0.180s
After:
$ time lscp
CNO DATE TIME MODE FLG BLKCNT ICNT 5769303 2015-02-22 19:31:33 cp - 108 1 5769304 2015-02-22 19:38:54 cp - 108 1
nilfs2: add helper to find existent block on metadata file
Add a new metadata file function, nilfs_mdt_find_block(), which finds
an existent block on a metadata file in a given range of blocks. This
function skips continuous hole blocks efficiently by using
nilfs_bmap_seek_key().