Kim Phillips [Thu, 26 Jul 2007 00:25:33 +0000 (19:25 -0500)]
mpc83xx: add support for the MPC8323E RDB
MPC8323E based board with 64MB fixed SDRAM, 16MB flash,
five 10/100 ethernet ports connected via an ICPlus IP175C
switch, one PCI slot, and serial. Features not supported
in this patch are SD card interface, 2 USB ports, and the
two phone ports.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Jerry Van Baren [Thu, 5 Jul 2007 01:34:24 +0000 (21:34 -0400)]
mpc83xx: Fix errors when CONFIG_OF_LIBFDT is enabled
Several node strings were not correct (trailing slashes and properties
in the strings)
Added setting of the timebase-frequency.
Improved error messages and use debug() instead of printf().
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Jerry Van Baren [Thu, 5 Jul 2007 01:27:30 +0000 (21:27 -0400)]
mpc83xx: Replace fdt_node_offset() with fdt_find_node_by_path().
The new name matches more closely the kernel's name, which is also
a much better description.
These are the mpc83xx changes made necessary by the function name change.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Gerald Van Baren <vanbaren@cideas.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Dave Liu [Mon, 25 Jun 2007 02:41:56 +0000 (10:41 +0800)]
mpc83xx: Add support for the display of reset status
83xx processor family has many reset sources, such as
power on reset, software hard reset, software soft reset,
JTAG, bus monitor, software watchdog, check stop reset,
external hard reset, external software reset.
sometimes, to figure out the fault of system, we need to
know the cause of reset early before the prompt of
u-boot present.
Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Dave Liu [Mon, 25 Jun 2007 05:21:12 +0000 (13:21 +0800)]
mpc83xx: Revise the MPC8360EMDS readme doc
When the rev2.x silicon mount on the MPC8360EMDS baord,
and if you are using the u-boot version after the commit 3fc0bd159103b536e1c54c6f4457a09b3aba66ca.
to make the ethernet interface usable, we have to setup
the jumpers correctly.
Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Timur Tabi [Tue, 3 Jul 2007 18:46:32 +0000 (13:46 -0500)]
FSL I2C driver programs the two I2C busses differently
The i2c_init() function in fsl_i2c.c programs the two I2C busses differently.
The second I2C bus has its slave address programmed incorrectly and is
missing a 5-us delay.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Timur Tabi [Tue, 3 Jul 2007 18:04:34 +0000 (13:04 -0500)]
Update SCCR programming in cpu_init_f() to support all 83xx processors
Update the cpu_init_f() function in cpu/mpc83xx/cpu_init.c to program the
bitfields for all 83xx processors. The code to update some bitfields was
compiled only on some processors. Now, the bitfields are programmed as long
as the corresponding CFG_SCCR option is defined in the board header file.
This means that the board header file should not define any CFG_SCCR macros
for bitfields that don't exist on that processor, otherwise the SCCR will be
programmed incorrectly.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Jason Jin [Tue, 10 Jul 2007 01:03:22 +0000 (09:03 +0800)]
Remove the bios emulator from MAI board.
The bios emulator in the MAI board can not pass compile
and have a lot of crap in it. remove it and will have a
clean and small bios emulator in the drivers directory
which can be uesed for every board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Jason Jin [Fri, 6 Jul 2007 00:34:56 +0000 (08:34 +0800)]
This is a BIOS emulator, porting from SciTech for u-boot, mainly for
ATI video card BIOS. and can be used for x86 code emulation by some
modifications.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Ed Swarthout [Thu, 2 Aug 2007 19:09:49 +0000 (14:09 -0500)]
Make MPC8641's PCI/PCI-E driver a common driver for many FSL parts.
All of the PCI/PCI-Express driver and initialization code that
was in the MPC8641HPCN port has now been moved into the common
drivers/fsl_pci_init.c. In a subsequent patch, this will be
utilized by the 85xx ports as well.
Common PCI-E IMMAP register blocks for FSL 85xx/86xx are added.
Also enable the second PCI-Express controller on 8641
by getting its BATS and CFG_ setup right.
Fixed a u16 vendor compiler warning in AHCI driver too.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Zhang Wei <wei.zhang@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
cm1_qp1 -> cm5200: single U-Boot image for modules from the cm5200 family.
Add the ability for modules from the Schindler cm5200 family to use a
single U-Boot image:
- rename cm1_qp1 to cm5200
- add run-time module detection
- parametrize SDRAM configuration according to the module we are running on
Few minor, board-specific fixes included in this patch:
- better MAC address handling
- updated default environment ('update' command uses +{filesize} now)
- improved error messages in the auto-update code
- allow booting U-Boot from RAM (CFG_RAMBOOT)
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com> Signed-off-by: Piotr Kruszynski <ppk@semihalf.com> Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Andy Fleming [Fri, 8 Jun 2007 21:41:18 +0000 (16:41 -0500)]
Remove erroneous errata code from Marvel 88E1111S driver
The Marvel 88E1111S driver for the TSEC was copied from the 88E1101 driver, and included a fix for an erratum which does not
exist on that part. Now it is removed
Signed-off-by: Andy Fleming <afleming@freescale.com>
Andy Fleming [Thu, 10 May 2007 22:50:01 +0000 (17:50 -0500)]
Polished the 85xx ADS config files
Made the boot commands use device trees by default.
Also moved the ramdisk to 1000000 (I think the previous address
was getting overridden during boot).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Andy Fleming [Wed, 9 May 2007 05:54:20 +0000 (00:54 -0500)]
tsec: Fix PHY code to match first driver
Jarrold Wen noticed that the generic PHY code always matches
under the current implementation. Change it so the first match
wins, and *only* unknown PHYs trigger the generic driver
Signed-off-by: Andy Fleming <afleming@freescale.com>
Andy Fleming [Tue, 8 May 2007 22:27:43 +0000 (17:27 -0500)]
Add support for CPM device tree configuration to 8560 ADS
* Adds code to modify CPM frequencies
* Cleans up the config file to #define TSEC and (for now) #undef FCC
* Adds the MII command for all 8560 ADS configurations
* Updates config file to provide convenience commands for booting
with a device tree
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
Ed Swarthout [Wed, 11 Jul 2007 19:51:35 +0000 (14:51 -0500)]
Start pci hose scan from hose->current_busno.
Ensure hose->current_busno is not less than first_busno. This fixes
broken board code which leaves current_busno=0 when first_busno is
greater than 0 for the cases with multiple controllers.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
[PCS440EP] - Show on the DIAG LEDs, if the SHA1 check failed
- now the Flash ST M29W040B is supported (not tested)
- fix the "led" command
- fix compile error, if BUILD_DIR is used
Stefan Roese [Sun, 8 Jul 2007 11:44:27 +0000 (13:44 +0200)]
Fix malloc problem introduced with the relocation fixup for the PPC platform
The relocation fixup didn't handle the malloc pointer initialization
correctly. This patch fixes this problem. Tested successfully on 4xx.
The relocation fixup patches for 4xx will follow soon.
Jon Loeliger [Tue, 10 Jul 2007 16:19:50 +0000 (11:19 -0500)]
disk/ doc/ lib_*/ and tools/: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Jon Loeliger [Tue, 10 Jul 2007 16:13:21 +0000 (11:13 -0500)]
drivers/: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Jon Loeliger [Tue, 10 Jul 2007 16:07:56 +0000 (11:07 -0500)]
fs/: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Jon Loeliger [Tue, 10 Jul 2007 16:05:02 +0000 (11:05 -0500)]
net/: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Jon Loeliger [Tue, 10 Jul 2007 16:02:44 +0000 (11:02 -0500)]
common/: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Jon Loeliger [Tue, 10 Jul 2007 15:48:22 +0000 (10:48 -0500)]
board/[j-z]*: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Jon Loeliger [Tue, 10 Jul 2007 15:39:10 +0000 (10:39 -0500)]
board/[A-Za-i]*: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Jon Loeliger [Tue, 10 Jul 2007 03:08:34 +0000 (22:08 -0500)]
Finally retire cmd_confdefs.h and CONFIG_BOOTP_MASK!
All of the choices for CONFIG_BOOTP_ are now documented in
the README file. You must now individually select exactly
the set that you want using a series of
#define CONFIG_BOOTP_<x>
statements in the board port config files now.
projects / karo-tx-uboot.git / log