Merge tag 'usb-serial-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.5-rc1
These updates add support for Moxa UPort 1100-series devices through a
new mxu11x0 driver.
The cp210x driver gains proper support for cp2108 devices by working
around a couple of firmware bugs, and generic wait-until-sent support
(e.g. for tcdrain) is also added.
Mathieu OTHACEHE [Mon, 28 Dec 2015 20:21:25 +0000 (21:21 +0100)]
USB: serial: add Moxa UPORT 11x0 driver
Add a driver which supports :
- UPort 1110 : 1 port RS-232 USB to Serial Hub.
- UPort 1130 : 1 port RS-422/485 USB to Serial Hub.
- UPort 1130I : 1 port RS-422/485 USB to Serial Hub with Isolation.
- UPort 1150 : 1 port RS-232/422/485 USB to Serial Hub.
- UPort 1150I : 1 port RS-232/422/485 USB to Serial Hub with Isolation.
This driver is based on GPL MOXA driver written by Hen Huang and available
on MOXA website. The original driver was based on io_ti serial driver.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org>
Linus Torvalds [Mon, 28 Dec 2015 02:12:21 +0000 (18:12 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
- Fix bitrot in __get_user_unaligned()
- EVA userspace accessor bug fixes.
- Fix for build issues with certain toolchains.
- Fix build error for VDSO with particular toolchain versions.
- Fix build error due to a variable that should have been removed by an
earlier patch
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix bitrot in __get_user_unaligned()
MIPS: Fix build error due to unused variables.
MIPS: VDSO: Fix build error
MIPS: CPS: drop .set mips64r2 directives
MIPS: uaccess: Take EVA into account in [__]clear_user
MIPS: uaccess: Take EVA into account in __copy_from_user()
MIPS: uaccess: Fix strlen_user with EVA
Linus Torvalds [Mon, 28 Dec 2015 02:06:31 +0000 (18:06 -0800)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A smallish set of fixes that we've been sitting on for a while now,
flushing the queue here so they go in. Summary:
A handful of fixes for OMAP, i.MX, Allwinner and Tegra:
- A clock rate and a PHY setup fix for i.MX6Q/DL
- A couple of fixes for the reduced serial bus (sunxi-rsb) on
Allwinner
- UART wakeirq fix for an OMAP4 board, timer config fixes for AM43XX.
- Suspend fix for Tegra124 Chromebooks
- Fix for missing implicit include that's different between
ARM/ARM64"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: Fix suspend hang on Tegra124 Chromebooks
bus: sunxi-rsb: Fix peripheral IC mapping runtime address
bus: sunxi-rsb: Fix primary PMIC mapping hardware address
ARM: dts: Fix UART wakeirq for omap4 duovero parlor
ARM: OMAP2+: AM43xx: select ARM TWD timer
ARM: OMAP2+: am43xx: enable GENERIC_CLOCKEVENTS_BROADCAST
fsl-ifc: add missing include on ARM64
ARM: dts: imx6: Fix Ethernet PHY mode on Ventana boards
ARM: dts: imx: Fix the assigned-clock mismatch issue on imx6q/dl
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
Linus Torvalds [Sun, 27 Dec 2015 04:08:47 +0000 (20:08 -0800)]
Merge tag 'pm+acpi-4.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix an ACPI processor driver regression introduced during the
4.3 cycle and a mistake in the recently added SCPI support in the
arm_big_little cpufreq driver.
Specifics:
- Fix a thermal management issue introduced by an ACPI processor
driver change made during the 4.3 development cycle that failed to
return 0 from a function on success which triggered an error
cleanup path every time it had been called that deleted useful data
structures created previously (Srinivas Pandruvada).
- Fix a variable data type issue in the arm_big_little cpufreq
driver's SCPI support code added recently that prevents error
handling in there from working correctly (Dan Carpenter)"
* tag 'pm+acpi-4.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: scpi-cpufreq: signedness bug in scpi_get_dvfs_info()
ACPI / processor: Fix thermal cooling device regression
Linus Torvalds [Sun, 27 Dec 2015 03:55:16 +0000 (19:55 -0800)]
Merge tag 'upstream-4.4-rc7' of git://git.infradead.org/linux-ubifs
Pull UBI bug fixes from Richard Weinberger:
"This contains four bug fixes for UBI"
* tag 'upstream-4.4-rc7' of git://git.infradead.org/linux-ubifs:
mtd: ubi: don't leak e if schedule_erase() fails
mtd: ubi: fixup error correction in do_sync_erase()
UBI: fix use of "VID" vs. "EC" in header self-check
UBI: fix return error code
Linus Torvalds [Sun, 27 Dec 2015 03:48:09 +0000 (19:48 -0800)]
Merge tag 'trace-v4.4-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace/recordmcount fix from Steven Rostedt:
"Russell King was reporting lots of warnings when he compiled his
kernel with ftrace enabled. With some investigation it was discovered
that it was his compile setup. He was using ccache with hard links,
which allowed recordmcount to process the same .o twice. When this
happens, recordmcount will detect that it was already done and give a
warning about it.
Russell fixed this by having recordmcount detect that the object file
has more than one hard link, and if it does, it unlinks the object
file after it maps it and processes then. This appears to fix the
issue.
As you did not like the fact that recordmcount modified the file in
place and thought that it should do the modifications in memory and
then write it out to disk and move it over the old file to prevent
other more subtle issues like the one above, a second patch is added
on top of Russell's to do just that. Luckily the original code had
write and lseek wrappers that I was able to modify to not do inplace
writes, but simply keep track of the changes made in memory. When a
write is made, a "update" flag is set, and at the end of processing,
if the update is set, then it writes the file with changes out to a
new file, and then renames it over the original one.
The file descriptor is still passed to the write and lseek wrappers
because removing that would cause the change to be more intrusive.
That can be removed in a follow up cleanup patch that can wait till
the next merge window"
* tag 'trace-v4.4-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/scripts: Have recordmcount copy the object file
scripts: recordmcount: break hardlinks
Merge tag 'phy-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.5
*) new PHY driver for hi6220 usb and rcar gen3 usb2
*) deprecate phy-omap-control driver. phy-omap-control driver was added
when there was no proper infrastructure for doing control module
initialization. The phy-omap-control driver is not an 'actual' PHY
driver and it was just a hack to do PHY related control module
initialization. Now with SYSCON framework in the kernel, control
module setttings can be done using APIs provided by syscon.
*) usbphy-internal pll creates the needed 480MHz and is also a
supply-clock back to the core clock-controller in Rockchip SoCs.
This is now modeled as a real clock.
*) calibrate mt65xx usb3 PHY for better eye diagram and receiver
sensitivity.
*) Miscellaneous cleanups.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Merge tag 'usb-ci-v4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-testing
Peter writes:
The chipidea changes for v4.5-rc1
- Delete static debug for chipidea driver.
- Suspend USB core when A device tries to switch to peripheral mode,
at former design, it just stopped SoF simply but USB core doesn't know it.
- Several small changes.
Linus Torvalds [Sat, 26 Dec 2015 22:58:06 +0000 (14:58 -0800)]
Merge tag 'arc-4.4-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Sorry for this late pull request, but these are all important fixes
for code introduced/updated in this release which we will otherwise
end up back porting.
- Unwinder rework (A revert followed by better fix)
- Build errors: MMUv2, modules with -Os
- highmem section mismatch build splat"
* tag 'arc-4.4-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: dw2 unwind: Catch Dwarf SNAFUs early
ARC: dw2 unwind: Don't bail for CIE.version != 1
Revert "ARC: dw2 unwind: Ignore CIE version !=1 gracefully instead of bailing"
ARC: Fix linking errors with CONFIG_MODULE + CONFIG_CC_OPTIMIZE_FOR_SIZE
ARC: mm: fix building for MMU v2
ARC: mm: HIGHMEM: Fix section mismatch splat
Linus Torvalds [Fri, 25 Dec 2015 21:19:50 +0000 (13:19 -0800)]
Merge branch 'parisc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc system call restart fix from Helge Deller:
"The architectural design of parisc always uses two instructions to
call kernel syscalls (delayed branch feature). This means that the
instruction following the branch (located in the delay slot of the
branch instruction) is executed before control passes to the branch
destination.
Depending on which assembler instruction and how it is used in
usersapce in the delay slot, this sometimes made restarted syscalls
like futex() and poll() failing with -ENOSYS"
* 'parisc-4.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix syscall restarts
1) Finally make perf stack backtraces stable on sparc, several problems
(mostly due to the context in which the user copies from the stack
are done) contributed to this.
From Rob Gardner.
2) Export ADI capability if the cpu supports it.
3) Hook up userfaultfd system call.
4) When faults happen during user copies we really have to clean up and
restore the FPU state fully. Also from Rob Gardner
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
tty/serial: Skip 'NULL' char after console break when sysrq enabled
sparc64: fix FP corruption in user copy functions
sparc64: Perf should save/restore fault info
sparc64: Ensure perf can access user stacks
sparc64: Don't set %pil in rtrap_nmi too early
sparc64: Add ADI capability to cpu capabilities
tty: serial: constify sunhv_ops structs
sparc: Hook up userfaultfd system call
Vijay Kumar [Wed, 23 Dec 2015 18:55:33 +0000 (10:55 -0800)]
tty/serial: Skip 'NULL' char after console break when sysrq enabled
When sysrq is triggered from console, serial driver for SUN hypervisor
console receives a console break and enables the sysrq. It expects a valid
sysrq char following with break. Meanwhile if driver receives 'NULL'
ASCII char then it disables sysrq and sysrq handler will never be invoked.
This fix skips calling uart sysrq handler when 'NULL' is received while
sysrq is enabled.
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com> Acked-by: Karl Volz <karl.volz@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Gardner [Wed, 23 Dec 2015 06:24:49 +0000 (23:24 -0700)]
sparc64: fix FP corruption in user copy functions
Short story: Exception handlers used by some copy_to_user() and
copy_from_user() functions do not diligently clean up floating point
register usage, and this can result in a user process seeing invalid
values in floating point registers. This sometimes makes the process
fail.
Long story: Several cpu-specific (NG4, NG2, U1, U3) memcpy functions
use floating point registers and VIS alignaddr/faligndata to
accelerate data copying when source and dest addresses don't align
well. Linux uses a lazy scheme for saving floating point registers; It
is not done upon entering the kernel since it's a very expensive
operation. Rather, it is done only when needed. If the kernel ends up
not using FP regs during the course of some trap or system call, then
it can return to user space without saving or restoring them.
The various memcpy functions begin their FP code with VISEntry (or a
variation thereof), which saves the FP regs. They conclude their FP
code with VISExit (or a variation) which essentially marks the FP regs
"clean", ie, they contain no unsaved values. fprs.FPRS_FEF is turned
off so that a lazy restore will be triggered when/if the user process
accesses floating point regs again.
The bug is that the user copy variants of memcpy, copy_from_user() and
copy_to_user(), employ an exception handling mechanism to detect faults
when accessing user space addresses, and when this handler is invoked,
an immediate return from the function is forced, and VISExit is not
executed, thus leaving the fprs register in an indeterminate state,
but often with fprs.FPRS_FEF set and one or more dirty bits. This
results in a return to user space with invalid values in the FP regs,
and since fprs.FPRS_FEF is on, no lazy restore occurs.
This bug affects copy_to_user() and copy_from_user() for NG4, NG2,
U3, and U1. All are fixed by using a new exception handler for those
loads and stores that are done during the time between VISEnter and
VISExit.
n.b. In NG4memcpy, the problematic code can be triggered by a copy
size greater than 128 bytes and an unaligned source address. This bug
is known to be the cause of random user process memory corruptions
while perf is running with the callgraph option (ie, perf record -g).
This occurs because perf uses copy_from_user() to read user stacks,
and may fault when it follows a stack frame pointer off to an
invalid page. Validation checks on the stack address just obscure
the underlying problem.
Signed-off-by: Rob Gardner <rob.gardner@oracle.com> Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Gardner [Wed, 23 Dec 2015 04:16:07 +0000 (21:16 -0700)]
sparc64: Perf should save/restore fault info
There have been several reports of random processes being killed with
a bus error or segfault during userspace stack walking in perf. One
of the root causes of this problem is an asynchronous modification to
thread_info fault_address and fault_code, which stems from a perf
counter interrupt arriving during kernel processing of a "benign"
fault, such as a TSB miss. Since perf_callchain_user() invokes
copy_from_user() to read user stacks, a fault is not only possible,
but probable. Validity checks on the stack address merely cover up the
problem and reduce its frequency.
The solution here is to save and restore fault_address and fault_code
in perf_callchain_user() so that the benign fault handler is not
disturbed by a perf interrupt.
Signed-off-by: Rob Gardner <rob.gardner@oracle.com> Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Gardner [Wed, 23 Dec 2015 04:16:06 +0000 (21:16 -0700)]
sparc64: Ensure perf can access user stacks
When an interrupt (such as a perf counter interrupt) is delivered
while executing in user space, the trap entry code puts ASI_AIUS in
%asi so that copy_from_user() and copy_to_user() will access the
correct memory. But if a perf counter interrupt is delivered while the
cpu is already executing in kernel space, then the trap entry code
will put ASI_P in %asi, and this will prevent copy_from_user() from
reading any useful stack data in either of the perf_callchain_user_X
functions, and thus no user callgraph data will be collected for this
sample period. An additional problem is that a fault is guaranteed
to occur, and though it will be silently covered up, it wastes time
and could perturb state.
In perf_callchain_user(), we ensure that %asi contains ASI_AIUS
because we know for a fact that the subsequent calls to
copy_from_user() are intended to read the user's stack.
[ Use get_fs()/set_fs() -DaveM ]
Signed-off-by: Rob Gardner <rob.gardner@oracle.com> Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Gardner [Tue, 22 Dec 2015 04:48:03 +0000 (21:48 -0700)]
sparc64: Don't set %pil in rtrap_nmi too early
Commit 28a1f53 delays setting %pil to avoid potential
hardirq stack overflow in the common rtrap_irq path.
Setting %pil also needs to be delayed in the rtrap_nmi
path for the same reason.
Signed-off-by: Rob Gardner <rob.gardner@oracle.com> Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Khalid Aziz [Thu, 17 Dec 2015 17:33:50 +0000 (10:33 -0700)]
sparc64: Add ADI capability to cpu capabilities
Add ADI (Application Data Integrity) capability to cpu capabilities list.
ADI capability allows virtual addresses to be encoded with a tag in
bits 63-60. This tag serves as an access control key for the regions
of virtual address with ADI enabled and a key set on them. Hypervisor
encodes this capability as "adp" in "hwcap-list" property in machine
description.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Mahfouz [Mon, 14 Dec 2015 23:37:57 +0000 (01:37 +0200)]
tty: serial: constify sunhv_ops structs
Constifies sunhv_ops structures in tty's serial
driver since they are not modified after their
initialization.
Detected and found using Coccinelle.
Suggested-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li Jun [Tue, 15 Dec 2015 09:51:29 +0000 (17:51 +0800)]
usb: chipidea: otg: use usb autosuspend to suspend bus for HNP
Directly manipulate the controller regsiter to suspend the usb bus
for HNP is not the proper way, this should be done through the usbcore
by usb autosuspend. So to start HNP, autosuspend support should be
added for OTG devices interface driver if it's not enabled.
Signed-off-by: Li Jun <jun.li@freescale.com> Signed-off-by: Peter Chen <peter.chen@freescale.com>
Peter Chen [Fri, 23 Oct 2015 02:33:58 +0000 (10:33 +0800)]
usb: chipidea: support debugfs without CONFIG_USB_CHIPIDEA_DEBUG
Since we need to mount debugfs to show/store the things we
want to debug, it is duplicated to add another configuration
to enable it. Meanwhile, with CONFIG_USB_CHIPIDEA_DEBUG,
we can't support chipidea debugfs at runtime.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Cc: Jun Li <jun.li@freescale.com>
usb: chipidea: udc: improve error handling on _hardware_enqueue
_hardware_enqueue() didn't check for errors when using
add_td_to_list() which can fail if dma_pool_alloc fails, thus
causing a kernel panic when lastnode->ptr is NULL.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com> Signed-off-by: Peter Chen <peter.chen@freescale.com>
Linus Torvalds [Wed, 23 Dec 2015 18:28:39 +0000 (10:28 -0800)]
Merge tag 'sound-4.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This shouldn't be a nightmare before Christmas: just a handful small
device-specific fixes for various ASoC and HD-audio drivers. Most of
them are stable fixes"
* tag 'sound-4.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix silent headphone output on MacPro 4,1 (v2)
ASoC: fsl_sai: fix no frame clk in master mode
ALSA: hda - Set SKL+ hda controller power at freeze() and thaw()
ASoC: sgtl5000: fix VAG power up timing
ASoC: rockchip: spdif: Set transmit data level to 16 samples
ASoC: wm8974: set cache type for regmap
ASoC: es8328: Fix shifts for mixer switches
ASoC: davinci-mcasp: Fix XDATA check in mcasp_start_tx
ASoC: es8328: Fix deemphasis values
Linus Torvalds [Wed, 23 Dec 2015 18:22:16 +0000 (10:22 -0800)]
Merge tag 'drm-intel-fixes-2015-12-23' of git://anongit.freedesktop.org/drm-intel
Pull i915 drm fixes from Jani Nikula:
"Here's a batch of i915 fixes all around. It may be slightly bigger
than one would hope for at this stage, but they've all been through
testing in our -next before being picked up for v4.4. Also, I missed
Dave's fixes pull earlier today just because I wanted an extra testing
round on this. So I'm fairly confident.
Wishing you all the things it is customary to wish this time of the
year"
* tag 'drm-intel-fixes-2015-12-23' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Correct max delay for HDMI hotplug live status checking
drm/i915: mdelay(10) considered harmful
drm/i915: Kill intel_crtc->cursor_bo
drm/i915: Workaround CHV pipe C cursor fail
drm/i915: Only spin whilst waiting on the current request
drm/i915: Limit the busy wait on requests to 5us not 10ms!
drm/i915: Break busywaiting for requests on pending signals
drm/i915: Disable primary plane if we fail to reconstruct BIOS fb (v2)
drm/i915: Set the map-and-fenceable flag for preallocated objects
drm/i915: Drop the broken cursor base==0 special casing
Linus Torvalds [Wed, 23 Dec 2015 18:11:12 +0000 (10:11 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Not much happening, should have dequeued this lot earlier.
One amdgpu, one nouveau and one exynos fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/exynos: atomic check only enabled crtc states
drm/nouveau/bios/fan: hardcode the fan mode to linear
drm/amdgpu: fix user fence handling
Takashi Iwai [Wed, 23 Dec 2015 07:30:28 +0000 (08:30 +0100)]
Merge tag 'asoc-fix-v4.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.4
A collection of small driver specific fixes here, nothing that'll affect
users who don't have the devices concerned. At least the wm8974 bug
indicates that there's not too many users of some of these devices.
usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller
R-Car H3 has USB3.0 peripheral controllers. This controller's has the
following features:
- Supports super, high and full speed
- Contains 30 pipes for bulk or interrupt transfer
- Contains dedicated DMA controller
This driver doesn't support the dedicated DMAC for now.
Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Linus Torvalds [Wed, 23 Dec 2015 00:00:25 +0000 (16:00 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"Three small fixes for 4.4 final. Specifically:
- The segment issue fix from Junichi, where the old IO path does a
bio limit split before potentially bouncing the pages. We need to
do that in the right order, to ensure that limitations are met.
- A NVMe surprise removal IO hang fix from Keith.
- A use-after-free in null_blk, introduced by a previous patch in
this series. From Mike Krinkin"
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: fix use-after-free error
block: ensure to split after potentially bouncing a bio
NVMe: IO ending fixes on surprise removal
Linus Torvalds [Tue, 22 Dec 2015 23:47:39 +0000 (15:47 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
- A series of fixes to the MTRR emulation, tested in the BZ by several
users so they should be safe this late
- A fix for a division by zero
- Two very simple ARM and PPC fixes
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Reload pit counters for all channels when restoring state
KVM: MTRR: treat memory as writeback if MTRR is disabled in guest CPUID
KVM: MTRR: observe maxphyaddr from guest CPUID, not host
KVM: MTRR: fix fixed MTRR segment look up
KVM: VMX: Fix host initiated access to guest MSR_TSC_AUX
KVM: arm/arm64: vgic: Fix kvm_vgic_map_is_active's dist check
kvm: x86: move tracepoints outside extended quiescent state
KVM: PPC: Book3S HV: Prohibit setting illegal transaction state in MSR
Linus Torvalds [Tue, 22 Dec 2015 23:43:18 +0000 (15:43 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Two late bug fixes for kernel 4.4.
Merry Christmas"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dis: Fix handling of format specifiers
s390/zcrypt: Fix AP queue handling if queue is full
Jon Hunter [Tue, 8 Dec 2015 10:26:49 +0000 (10:26 +0000)]
ARM: tegra: Fix suspend hang on Tegra124 Chromebooks
Enabling CPUFreq support for Tegra124 Chromebooks is causing the Tegra124
to hang when resuming from suspend.
When CPUFreq is enabled, the CPU clock is changed from the PLLX clock to
the DFLL clock during kernel boot. When resuming from suspend the CPU
clock is temporarily changed back to the PLLX clock before switching back
to the DFLL. If the DFLL is operating at a much lower frequency than the
PLLX when we enter suspend, and so the CPU voltage rail is at a voltage
too low for the CPUs to operate at the PLLX frequency, then the device
will hang.
Please note that the PLLX is used in the resume sequence to switch the CPU
clock from the very slow 32K clock to a faster clock during early resume
to speed up the resume sequence before the DFLL is resumed.
Ideally, we should fix this by setting the suspend frequency so that it
matches the PLLX frequency, however, that would be a bigger change. For
now simply disable CPUFreq support for Tegra124 Chromebooks to avoid the
hang when resuming from suspend.
Fixes: 9a0baee960a7 ("ARM: tegra: Enable CPUFreq support for Tegra124
Chromebooks")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 22 Dec 2015 21:24:29 +0000 (13:24 -0800)]
Merge tag 'omap-for-v4.4/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few fixes for omaps to allow am437x only builds to boot properly with
CPU_IDLE and ARM TWD timer. This is probably a common configuration setup
for people making products with these SoCs so let's make sure it works.
Also a wakeirq fix for duovero parlor making my life a bit easier as that
allows me to run basic PM regression tests on it.
It would be nice to have these in v4.4, but if it gets too late for that
because of the holidays, it is not super critical if these get merged for
v4.5.
* tag 'omap-for-v4.4/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix UART wakeirq for omap4 duovero parlor
ARM: OMAP2+: AM43xx: select ARM TWD timer
ARM: OMAP2+: am43xx: enable GENERIC_CLOCKEVENTS_BROADCAST
Olof Johansson [Tue, 22 Dec 2015 19:49:21 +0000 (11:49 -0800)]
Merge tag 'imx-fixes-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.4, 3rd round:
- Fix Ethernet PHY mode on i.MX6 Ventana boards, which can result in
a non-functional Ethernet when Marvell phy driver rather than generic
phy driver is selected.
- Fix an assigned-clock configuration bug on imx6qdl-sabreauto board
which was introduced by commit ed339363de1b ("ARM: dts:
imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously").
* tag 'imx-fixes-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: Fix Ethernet PHY mode on Ventana boards
ARM: dts: imx: Fix the assigned-clock mismatch issue on imx6q/dl
Heiko Stübner [Fri, 18 Dec 2015 18:30:59 +0000 (19:30 +0100)]
usb: dwc2: add shutdown callback to platform variant
In specific conditions (involving usb hubs) dwc2 devices can create a
lot of interrupts, even to the point of overwhelming devices running
at low frequencies. Some devices need to do special clock handling
at shutdown-time which may bring the system clock below the threshold
of being able to handle the dwc2 interrupts. Disabling dwc2-irqs
in a shutdown callbacks prevents reboots/poweroffs from getting stuck
in such cases.
The hsotg struct already contains an unused irq element, so we can
just use it to store the irq number for the shutdown callback.
Reviewed-by: Douglas Anderson <dianders@chromium.org> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Du, Changbin [Fri, 18 Dec 2015 07:36:40 +0000 (15:36 +0800)]
usb: gadget: forbid queuing request to a disabled ep
Queue a request to disabled ep doesn't make sense, and induce caller
make mistakes.
Here is a example for the android mtp gadget function driver. A mem
corruption can happen on below senario.
1) On disconnect, mtp driver disable its EPs,
2) During send_file_work and receive_file_work, mtp queues a request
to ep. (The mtp driver need improve its synchronization logic!)
3) mtp_function_unbind is invoked and all mtp requests are freed.
4) when udc process the request queued on step 2, will cause kernel
NULL pointer dereference exception.
Signed-off-by: Du, Changbin <changbin.du@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Marek Vasut [Fri, 18 Dec 2015 02:26:17 +0000 (03:26 +0100)]
usb: dwc2: gadget: Repair DSTS register decoding
The "enumspd" field is located in register DSTS[2:1], but the code
which checks the bitfield does not shift the value accordingly. This
in turn causes incorrect detection of gadget link partner speed in
dwc2_hsotg_irq_enumdone() .
Shift the value accordingly to fix the problem with speed detection.
Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Felipe Balbi <balbi@ti.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn [Thu, 17 Dec 2015 19:18:41 +0000 (11:18 -0800)]
usb: dwc2: gadget: Remove call to dwc2_hsotg_init()
Remove call to dwc2_hsotg_init() from dwc2_gadget_init(). The
gadget_init function should not access any device registers because the
mode isn't guaranteed here.
Also, this is already called elsewhere before anything starts on the
gadget so it is not necessary here.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn [Thu, 17 Dec 2015 19:17:45 +0000 (11:17 -0800)]
usb: dwc2: gadget: Use hw params from core
Use the previously cached hw params in the gadget. This saves a reset
and force mode in the gadget initialization during probe and makes
getting the hardware parameters consistent between gadget and host.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn [Thu, 17 Dec 2015 19:17:31 +0000 (11:17 -0800)]
usb: dwc2: Improve handling of host and device hwparams
Adds separate functions to get the host and device specific hardware
parameters. The functions check whether the parameters need to be read
at all, depending on dr_mode, and forces the mode only if necessary.
This saves some delays during probe. This also adds two device mode
parameters that will be used by the gadget.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn [Thu, 17 Dec 2015 19:17:12 +0000 (11:17 -0800)]
usb: dwc2: Add functions to set and clear force mode
Added functions to set force mode for host and device. These functions
will check the current mode and only force if needed thus avoiding
unnecessary force mode delays. However clearing the mode is currently
done unconditionally and with the delay in place. This is needed during
the connector ID status change interrupt in order to ensure that the
mode has changed properly. This preserves the old behavior only for this
case. The warning comment about this is moved into the clear mode
condition.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn [Thu, 17 Dec 2015 19:16:58 +0000 (11:16 -0800)]
usb: dwc2: Move reset into dwc2_get_hwparams()
The reset is required to get reset values of the hardware parameters but
the force mode is not. Move the base reset into dwc2_get_hwparams() and
do the reset and force mode afterwards.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn [Thu, 17 Dec 2015 19:16:45 +0000 (11:16 -0800)]
usb: dwc2: Move mode querying functions into core.h
These functions should go in core.h where they can be called from core,
device, or host.
Signed-off-by: John Youn <johnyoun@synopsys.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn [Thu, 17 Dec 2015 19:16:31 +0000 (11:16 -0800)]
usb: dwc2: Fix dr_mode validation
The dr_mode parameter was being checked against how the dwc2 module
was being configured at compile time. But it wasn't checked against
the hardware capabilities, nor were the hardware capabilities checked
against the compilation parameters.
This commit adds those checks and adjusts dr_mode to an appropriate
value, if needed. If the hardware capabilities and module compilation
do not match then we fail as it wouldn't be possible to run properly.
The hardware, module, and dr_mode, can each be set to host, device,
or otg. Check that all these values are compatible and adjust the
value of dr_mode if possible.
The following table summarizes the behavior:
actual
HW MOD dr_mode dr_mode
------------------------------
HST HST any : HST
HST DEV any : ---
HST OTG any : HST
DEV HST any : ---
DEV DEV any : DEV
DEV OTG any : DEV
OTG HST any : HST
OTG DEV any : DEV
OTG OTG any : dr_mode
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn [Thu, 17 Dec 2015 19:16:17 +0000 (11:16 -0800)]
usb: dwc2: Add functions to check the HW OTG config
Added functions to query the GHWCFG2.OTG_MODE. This tells us whether the
controller hardware is configured for OTG, device-only, or host-only.
Signed-off-by: John Youn <johnyoun@synopsys.com> Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn [Thu, 17 Dec 2015 19:16:03 +0000 (11:16 -0800)]
usb: dwc2: Add dwc2_core_reset()
dwc2_core_reset() was previously renamed to
dwc2_core_reset_and_dr_force_mode(). Now add back dwc2_core_reset() which
performs only a basic core reset without forcing the mode.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn [Thu, 17 Dec 2015 19:15:49 +0000 (11:15 -0800)]
usb: dwc2: Rename dwc2_core_reset()
Renamed dwc2_core_reset() to dwc2_core_reset_and_force_dr_mode(). This
describes what it is doing more accurately. This is in preparation of
introducing a plain dwc2_core_reset() function that only performs the
reset and doesn't force the mode.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
John Youn [Thu, 17 Dec 2015 19:15:35 +0000 (11:15 -0800)]
usb: dwc2: Reorder AHBIDLE and CSFTRST in dwc2_core_reset()
According to the databook, the core soft reset should be done before
checking for AHBIDLE. The gadget version of core reset had it correct
but the hcd version did not. This fixes the hcd version.
Signed-off-by: John Youn <johnyoun@synopsys.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
Douglas Anderson [Thu, 17 Dec 2015 19:15:21 +0000 (11:15 -0800)]
usb: dwc2: Avoid more calls to dwc2_core_reset()
Calls to dwc2_core_reset() are currently very slow, taking at least
150ms (possibly more). It behooves us to take as many of these calls
out as possible.
It turns out that the calls in dwc2_fs_phy_init() and dwc2_hs_phy_init()
should (as documented in the code) only be needed if we need to do a PHY
SELECT. That means that if we see that we can avoid the PHY SELECT then
we can avoid the reset.
This patch appears to successfully bypass two resets (one per USB
device) on rk3288-based ARM Chromebooks.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Yunzhi Li [Thu, 17 Dec 2015 19:15:08 +0000 (11:15 -0800)]
usb: dwc2: reduce dwc2 driver probe time
I found that the probe function of dwc2 driver takes much time
when kernel boot up. There are many long delays in the probe
function these take almost 1 second.
This patch trying to reduce unnecessary delay time.
In dwc2_core_reset() I see it use two at least 20ms delays to
wait AHB idle and core soft reset, but dwc2 data book said that
dwc2 core soft reset and AHB idle just need a few clocks (I think
it refers to AHB clock, and AHB clock run at 150MHz in my RK3288
board), so 20ms is too long, delay 1us for wait AHB idle and soft
reset is enough.
And in dwc2_get_hwparams() it takes 150ms to wait ForceHostMode
and ForceDeviceMode valid but in data book it said software must
wait at least 25ms before the change to take effect, so I reduce
this time to 25ms~50ms. By the way, is there any state bit show
that the force mode take effect ? Could we poll curmod bit for
figuring out if the change take effect ?
It seems that usleep_range() at boot time will pick the longest
value in the range. In dwc2_core_reset() there is a very long
delay takes 200ms, and this function run twice when probe, could
any one tell me is this delay time resonable ?
I have tried this patch in my RK3288-evb board. It works well.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Douglas Anderson [Thu, 17 Dec 2015 19:14:54 +0000 (11:14 -0800)]
usb: dwc2: Speed dwc2_get_hwparams() on some host-only ports
On some host-only DWC2 ports (like the one in rk3288) when we set
GUSBCFG_FORCEHOSTMODE in GUSBCFG and then read back, we don't see the
bit set. Presumably that's because the port is always forced to HOST
mode so there's no reason to implement these status bits.
Since we know dwc2_core_reset() is always called before
dwc2_get_hwparams() and we know dwc2_core_reset() should have set
GUSBCFG_FORCEHOSTMODE whenever hsotg->dr_mode == USB_DR_MODE_HOST, we
can just check hsotg->dr_mode to decide that we can skip the delays in
dwc2_get_hwparams().
Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Douglas Anderson [Thu, 17 Dec 2015 19:14:40 +0000 (11:14 -0800)]
usb: dwc2: Avoid double-reset at boot time
In (usb: dwc2: reset dwc2 core before dwc2_get_hwparams()) we added an
extra reset to the probe path for the dwc2 USB controllers. This
allowed proper detection of parameters even if the firmware had already
used the USB part.
Unfortunately, this extra reset is quite slow and is affecting boot
speed. We can avoid the double-reset by skipping the extra reset that
would happen just after the one we added. Logic that explains why this
is safe:
* As of the CL mentioned above, we now always call dwc2_core_reset() in
dwc2_driver_probe() before dwc2_hcd_init().
* The only caller of dwc2_hcd_init() is dwc2_driver_probe(), so we're
guaranteed that dwc2_core_reset() was called before dwc2_hdc_init().
* dwc2_hdc_init() is the only caller that passes an irq other than -1 to
dwc2_core_init(). Thus if dwc2_core_init() is called with an irq
other than -1 we're guaranteed that dwc2_core_reset was called before
dwc2_core_init().
...this allows us to remove the dwc2_core_reset() in dwc2_core_init() if
irq is not < 0.
Note that since "irq" wasn't used in the function dwc2_core_init()
anyway and since select_phy was always set at exactly the same times we
could avoid the reset, we remove "irq" and rename "select_phy" to
"initial_setup" and adjust the callers accordingly.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Yunzhi Li [Thu, 17 Dec 2015 19:14:26 +0000 (11:14 -0800)]
usb: dwc2: reset dwc2 core before dwc2_get_hwparams()
We initiate dwc2 usb controller in BIOS, dwc2_core_reset() should
be called before dwc2_get_hwparams() to reset core registers to
default value. Without this the FIFO setting might be incorrect
because calculating FIFO size need power-on value of
GRXFSIZ/GNPTXFSIZ/HPTXFSIZ registers.
This patch could avoid warnning massage like in rk3288 platform:
[ 2.074764] dwc2 ff580000.usb: 256 invalid for
host_perio_tx_fifo_size. Check HW configuration.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Douglas Anderson [Thu, 17 Dec 2015 19:14:12 +0000 (11:14 -0800)]
usb: dwc2: Restore GUSBCFG in dwc2_get_hwparams()
Previously dwc2_get_hwparams() was changing GUSBCFG and not putting it
back the way it was (specifically it set and cleared FORCEHOSTMODE).
Since we want to move dwc2_core_reset() _before_ dwc2_get_hwparams() we
should make sure dwc2_get_hwparams() isn't messing with things in a
permanent way.
Since we're now looking at GUSBCFG, it's obvious that we shouldn't need
all the extra delays if FORCEHOSTMODE was already set. This will avoid
some delays for any ports that have forced host mode.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Gregory Herrero [Mon, 7 Dec 2015 11:07:31 +0000 (12:07 +0100)]
usb: dwc2: gadget: don't overwrite DCTL register on NAKEFF interrupts
When receiving GINTSTS_GINNAKEFF or GINTSTS_GOUTNAKEFF interrupt,
DCTL will be overwritten with DCTL_CGOUTNAK or DCTL_CGNPINNAK values.
Instead of overwriting it, write only needed bits.
It could cause an issue if GINTSTS_GINNAKEFF or GINTSTS_GOUTNAKEFF
interrupt is received after dwc2 disabled pullup by writing
DCTL_SFTDISCON bit.
Pullup will then be re-enabled whereas it should not.
Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Du, Changbin [Fri, 4 Dec 2015 07:38:23 +0000 (15:38 +0800)]
usb: dwc2: fix transfer stop programming for out endpoint
To stop an out endpoint, software should set sets the Global OUT NAK,
but not the Global Non-periodic IN NAK. This driver bug leads the out-ep
failed be in disabled state with below error.
dwc2_hsotg_ep_stop_xfr: timeout DOEPCTL.EPDisable
Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Du, Changbin <changbin.du@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Baolin Wang [Sat, 21 Nov 2015 07:44:53 +0000 (15:44 +0800)]
usb: gadget: Add the console support for usb-to-serial port
It dose not work when we want to use the usb-to-serial port based
on one usb gadget as a console. Thus this patch adds the console
initialization to support this request.
To avoid the re-entrance when transferring data with usb endpoint,
it introduces a kthread to do the IO transmission.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
Mike Krinkin [Tue, 15 Dec 2015 09:56:40 +0000 (12:56 +0300)]
null_blk: fix use-after-free error
blk_end_request_all may free request, so we need to save
request_queue pointer before blk_end_request_all call.
The problem was introduced in commit cf8ecc5a8455266f8d51
("null_blk: guarantee device restart in all irq modes")
and causes general protection fault with slab poisoning
enabled.
Fixes: cf8ecc5a8455266f8d51 ("null_blk: guarantee device
restart in all irq modes")
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com> Reviewed-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Junichi Nomura [Tue, 22 Dec 2015 17:23:44 +0000 (10:23 -0700)]
block: ensure to split after potentially bouncing a bio
blk_queue_bio() does split then bounce, which makes the segment
counting based on pages before bouncing and could go wrong. Move
the split to after bouncing, like we do for blk-mq, and the we
fix the issue of having the bio count for segments be wrong.
Fixes: 54efd50bfd87 ("block: make generic_make_request handle arbitrarily sized bios") Cc: stable@vger.kernel.org Tested-by: Artem S. Tashkinov <t.artem@lycos.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Keith Busch [Fri, 11 Dec 2015 20:14:28 +0000 (13:14 -0700)]
NVMe: IO ending fixes on surprise removal
This patch fixes a lost request discovered during IO + hot removal.
The driver's pci removal deletes gendisks prior to shutting down the
controller to allow dirty data to sync. Dirty data can not be synced on
a surprise removal, though, and would potentially block indefinitely.
The driver previously had marked the queue as dying in this scenario
to prevent new requests from attempting, however it will still block
for requests that already entered the queue. This patch fixes this by
quiescing IO first, then aborting the requeued requests before deleting
disks.
Andrew Honig [Wed, 18 Nov 2015 22:50:23 +0000 (14:50 -0800)]
KVM: x86: Reload pit counters for all channels when restoring state
Currently if userspace restores the pit counters with a count of 0
on channels 1 or 2 and the guest attempts to read the count on those
channels, then KVM will perform a mod of 0 and crash. This will ensure
that 0 values are converted to 65536 as per the spec.
This is CVE-2015-7513.
Signed-off-by: Andy Honig <ahonig@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Tue, 22 Dec 2015 14:20:00 +0000 (15:20 +0100)]
KVM: MTRR: treat memory as writeback if MTRR is disabled in guest CPUID
Virtual machines can be run with CPUID such that there are no MTRRs.
In that case, the firmware will never enable MTRRs and it is obviously
undesirable to run the guest entirely with UC memory. Check out guest
CPUID, and use WB memory if MTRR do not exist.
Cc: qemu-stable@nongnu.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=107561 Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Mon, 14 Dec 2015 15:57:31 +0000 (16:57 +0100)]
KVM: MTRR: observe maxphyaddr from guest CPUID, not host
Conversion of MTRRs to ranges used the maxphyaddr from the boot CPU.
This is wrong, because var_mtrr_range's mask variable then is discontiguous
(like FF00FFFF000, where the first run of 0s corresponds to the bits
between host and guest maxphyaddr). Instead always set up the masks
to be full 64-bit values---we know that the reserved bits at the top
are zero, and we can restore them when reading the MSR. This way
var_mtrr_range gets a mask that just works.
Fixes: a13842dc668b40daef4327294a6d3bdc8bd30276 Cc: qemu-stable@nongnu.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=107561 Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes the slow-down of VM running with pci-passthrough, since some MTRR
range changed from MTRR_TYPE_WRBACK to MTRR_TYPE_UNCACHABLE. Memory in the
0K-640K range was incorrectly treated as uncacheable.
Ralf Baechle [Fri, 27 Nov 2015 18:17:01 +0000 (19:17 +0100)]
MIPS: Fix build error due to unused variables.
c861519fcf95b2d46cb4275903423b43ae150a40 ("MIPS: Fix delay loops which may
be removed by GCC.") which made it upstream was an outdated version of the
patch and is lacking some the removal of two variables that became unused
thus resulting in further warnings and build breakage. The commit
from ae878615d7cee5d7346946cf1ae1b60e427013c2 was correct however.
Qais Yousef [Tue, 8 Dec 2015 10:11:43 +0000 (10:11 +0000)]
MIPS: VDSO: Fix build error
Commit ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") introduced a
build error.
For MIPS VDSO to be compiled it requires binutils version 2.25 or above but
the check in the Makefile had inverted logic causing it to be compiled in if
binutils is below 2.25.
Paul Burton [Wed, 5 Aug 2015 22:42:40 +0000 (15:42 -0700)]
MIPS: CPS: drop .set mips64r2 directives
Commit 977e043d5ea1 ("MIPS: kernel: cps-vec: Replace mips32r2 ISA level
with mips64r2") leads to .set mips64r2 directives being present in 32
bit (ie. CONFIG_32BIT=y) kernels. This is incorrect & leads to MIPS64
instructions being emitted by the assembler when expanding
pseudo-instructions. For example the "move" instruction can legitimately
be expanded to a "daddu". This causes problems when the kernel is run on
a MIPS32 CPU, as CONFIG_32BIT kernels of course often are...
Fix this by dropping the .set <ISA> directives entirely now that Kconfig
should be ensuring that kernels including this code are built with a
suitable -march= compiler flag.
projects / karo-tx-linux.git / log