Ben Hutchings [Thu, 1 Sep 2011 12:09:59 +0000 (12:09 +0000)]
sfc: Use 64-bit writes for TX push where possible
This was originally done as part of commit 65f0b417dee94f779ce9b77102b7d73c93723b39 ("sfc: Use write-combining to
reduce TX latency"), but that had to be reverted.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the processor model, write-combining may result in
reordering that the NIC will not tolerate. This typically results
in a DMA error event and reset by the driver, logged as:
Enable changing advertisement settings via ethtool.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Change XMAC loopback type from CORE LOCAL to LINE LOCAL for the BCM578xx due to intermittent problem with the loopback with this configuration.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Remove remote fault detection as a tactic retreat due to link issues involved with it.
Once issue is resolved, this feature will be restored again.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Enable FEC(Forward Error Correction) for 57810-KR to reduce link errors.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ETS bandwidth of 0% is not allowed by driver, so provide alternative HW configuration for this case.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: don't clear IFF_XMIT_DST_RELEASE in ether_setup
d88733150 introduced the IFF_SKB_TX_SHARING flag, which I unilaterally set in
ether_setup. In doing this I didn't realize that other flags (such as
IFF_XMIT_DST_RELEASE) might be set prior to calling the ether_setup routine.
This patch changes ether_setup to or in SKB_TX_SHARING so as not to
inadvertently clear other existing flags. Thanks to Pekka Riikonen for pointing
out my error
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Pekka Riikonen <priikone@iki.fi> CC: "David S. Miller" <davem@davemloft.net> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dev_forward_skb loops an skb back into host networking
stack which might hang on the memory indefinitely.
In particular, this can happen in macvtap in bridged mode.
Copy the userspace fragments to avoid blocking the
sender in that case.
As this patch makes skb_copy_ubufs extern now,
I also added some documentation and made it clear
the SKBTX_DEV_ZEROCOPY flag automatically instead
of doing it in all callers. This can be made into a separate
patch if people feel it's worth it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dpward [Wed, 31 Aug 2011 06:05:27 +0000 (06:05 +0000)]
net: Make flow cache namespace-aware
flow_cache_lookup will return a cached object (or null pointer) that the
resolver (i.e. xfrm_policy_lookup) previously found for another namespace
using the same key/family/dir. Instead, make the namespace part of what
identifies entries in the cache.
As before, flow_entry_valid will return 0 for entries where the namespace
has been deleted, and they will be removed from the cache the next time
flow_cache_gc_task is run.
Reported-by: Andrew Dickinson <whydna@whydna.net> Signed-off-by: David Ward <david.ward@ll.mit.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
net/can/af_can.c: Change del_timer to del_timer_sync
This is important for SMP platform to check if timer function is
executing on other CPU with deleting the timer.
Signed-off-by: Rajan Aggarwal <Rajan Aggarwal rajan.aggarwal85@gmail.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 30 Aug 2011 00:08:45 +0000 (00:08 +0000)]
bnx2x: don't access removed registers on 57712 and above
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 30 Aug 2011 00:08:44 +0000 (00:08 +0000)]
bnx2x: init fw_seq after undi_unload is done
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 30 Aug 2011 00:08:43 +0000 (00:08 +0000)]
bnx2x: don't reset device while reading its configuration.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 30 Aug 2011 00:08:42 +0000 (00:08 +0000)]
bnx2x: fix MF for 4-port devices
Number of VNs for 4-port devices is 2 instead of 4
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 30 Aug 2011 00:08:40 +0000 (00:08 +0000)]
bnx2x: decrease print level to debug
It may happen every link toggle.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 30 Aug 2011 00:08:39 +0000 (00:08 +0000)]
bnx2x: fix BRB thresholds for dropless_fc mode
Fix the thresholds according to 5778x HW and increase rx_ring size
to suit new thresholds in dropless_fc mode.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Mon, 12 Sep 2011 19:09:10 +0000 (12:09 -0700)]
iwlagn: fix command queue timeout
If the command queue is constantly busy,
which can happen in P2P, the hangcheck
timer will frequently find a command in
it and will eventually reset the device
because nothing sets the timestamp for
this queue when commands are processed.
Fix this by setting the timestamp when
a command completes.
Cc: stable@kernel.org #2.6.39, #3.0.0 #3.1.0 Signed-off-by: Johannes Berg <johannes.berg@intel.com> SIgned-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 12 Sep 2011 19:08:25 +0000 (21:08 +0200)]
iwlagn: fix stack corruption
Alexander reported a strange crash in iwlagn that
Meenakshi and Wey couldn't reproduce. I just ran
into the same issue and tracked it down to stack
corruption. This fixes it.
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com> Cc: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Reported-by: Alexander Diewald <alex@diewald.cc> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
when the device is yanked out ath_pci_remove starts doing the cleanups,
unregistering the hardware etc. so we should bail out immediately when
we get drv_flush callback from mac80211 when the card is being unplugged.
the panic occurs after we had associated to an AP.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 6 Sep 2011 10:47:39 +0000 (12:47 +0200)]
mac80211: fix missing sta_lock in __sta_info_destroy
Since my commit 34e895075e21be3e21e71d6317440d1ee7969ad0
("mac80211: allow station add/remove to sleep") there is
a race in mac80211 when it clears the TIM bit because a
sleeping station disconnected, the spinlock isn't held
around the relevant code any more. Use the right API to
acquire the spinlock correctly.
Cc: stable@kernel.org [2.6.34+] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
George [Sat, 3 Sep 2011 15:58:48 +0000 (10:58 -0500)]
rtlwifi: Fix problem when switching connections
The driver fails to clear encryption keys making it impossible
to switch connections.
Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> [2.6.39+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
George [Sat, 3 Sep 2011 15:58:47 +0000 (10:58 -0500)]
rtlwifi: rtl8192su: Fix problem connecting to HT-enabled AP
The driver fails to connect to 802.11n-enabled APs. The patch fixes
Bug #42262.
Signed-off-by: George <george0505@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> [2.6.39+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 29 Aug 2011 08:06:14 +0000 (10:06 +0200)]
ath9k_hw: fix calibration on 5 ghz
ADC calibrations cannot run on 5 GHz with fast clock enabled. They
need to be disabled, otherwise they'll hang and IQ mismatch calibration
will not be run either.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reported-by: Adrian Chadd <adrian@freebsd.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trying to connect to 5GHz we can provide negative index to
mac80211 what trigger BUG_ON. Reason of iwl-3945-rs malfunction
on 5GHz is unknown and needs further investigation. For now, to
do not trigger a bug, correct value and just print WARNING.
Reported-and-tested-by: Jan Teichmann <jan.teichmann@gmail.com> Cc: stable@kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
françois romieu [Thu, 25 Aug 2011 05:02:49 +0000 (05:02 +0000)]
cassini: init before use in cas_interruptN.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Spotted-by: Thomas Jarosch <thomas.jarosch@intra2net.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CC drivers/net/sh_eth.o
drivers/net/sh_eth.c:1115: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘sh_eth_interrupt’
drivers/net/sh_eth.c: In function ‘sh_eth_open’:
drivers/net/sh_eth.c:1387: error: implicit declaration of function ‘request_irq’
drivers/net/sh_eth.c:1387: error: ‘sh_eth_interrupt’ undeclared (first use in this function)
drivers/net/sh_eth.c:1387: error: (Each undeclared identifier is reported only once
drivers/net/sh_eth.c:1387: error: for each function it appears in.)
drivers/net/sh_eth.c:1391: error: ‘IRQF_SHARED’ undeclared (first use in this function)
drivers/net/sh_eth.c:1424: error: implicit declaration of function ‘free_irq’
make[2]: *** [drivers/net/sh_eth.o] Error 1
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
According to the DP83865 datasheet we need to clear
the interrupt status bit by writing a 1 to the
corresponding bit in INT_CLEAR (2:0 are reserved).
Proposed and tested by Thorsten.
Signed-off-by: Thorsten Schubert <tshu@msc-ge.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dereferencing a user pointer directly from kernel-space without going
through the copy_from_user family of functions is a bad idea. Two of
such usages can be found in the sendmsg code path called from sendmmsg,
added by
Usages are performed through memcmp() and memcpy() directly. Fix those
by using the already copied msg_sys structure instead of the __user *msg
structure. Note that msg_sys can be set to NULL by verify_compat_iovec()
or verify_iovec(), which requires additional NULL pointer checks.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: David Goulet <dgoulet@ev0ke.net> CC: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> CC: Anton Blanchard <anton@samba.org> CC: David S. Miller <davem@davemloft.net> CC: stable <stable@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 22 Aug 2011 19:32:42 +0000 (19:32 +0000)]
arp: fix rcu lockdep splat in arp_process()
Dave Jones reported a lockdep splat triggered by an arp_process() call
from parp_redo().
Commit faa9dcf793be (arp: RCU changes) is the origin of the bug, since
it assumed arp_process() was called under rcu_read_lock(), which is not
true in this particular path.
Instead of adding rcu_read_lock() in parp_redo(), I chose to add it in
neigh_proxy_process() to take care of IPv6 side too.
Yan, Zheng [Tue, 23 Aug 2011 22:54:33 +0000 (22:54 +0000)]
bridge: Pseudo-header required for the checksum of ICMPv6
Checksum of ICMPv6 is not properly computed because the pseudo header is not used.
Thus, the MLD packet gets dropped by the bridge.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com> Reported-by: Ang Way Chuang <wcang@sfc.wide.ad.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 24 Aug 2011 18:25:08 +0000 (11:25 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wiimote: Add status and return request handlers
HID: wiimote: Add drm request
HID: wiimote: Register led class devices
HID: wiimote: Correctly call HID open/close callbacks
HID: wiimote: Simplify synchronization
HID: usbhid: Add support for SiGma Micro chip
HID: add support for new revision of Apple aluminum keyboard
ath9k: Fix PS wrappers in ath9k_set_coverage_class
this callback is called during suspend/resume and also via iw command.
it configures parameters like sifs, slottime, acktimeout in
ath9k_hw_init_global_settings where few REG_READ, REG_RMW are also done
and hence the need for PS wrappers
Cc: stable@kernel.org Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: Fix mismatch in carl9170_op_set_key mutex lock-unlock
If is_main_vif(ar, vif) reports that we have to fall back
to software encryption, we goto err_softw; before locking ar->mutex.
As a result, we have unprotected call to carl9170_set_operating_mode
and unmatched mutex_unlock.
The patch fix the issue by adding mutex_lock before goto.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: <stable@kernel.org> Acked-By: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds [Wed, 24 Aug 2011 16:19:03 +0000 (09:19 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ad714x - read the interrupt status registers in a row
Input: ad714x - use DMA-safe buffers for spi_write()
Input: ad714x - fix endianness issues
Input: ad714xx-spi - force SPI bus into the default 8-bit mode
Input: ep93xx_keypad - add missing include of linux/module.h
Input: tnetv107x-ts - add missing include of linux/module.h
Input: max11801_ts - correct license statement
Input: atmel_mxt_ts - report pressure information from the driver
Input: bcm5974 - Add support for newer MacBookPro8,2
Input: wacom - report id 3 returns 4 bytes of data
Input: wacom - add WAC_MSG_RETRIES define
Input: wacom - add support for the Wacom Bamboo Pen (CTL-660/K)
Input: tegra-kbc - correct call to input_free_device
Input: mpu3050 - correct call to input_free_device
Input: bcm5974 - add support for touchpads found in MacBookAir4,2
Input: mma8450 - fix module device table type
Input: remove CLOCK_TICK_RATE from analog joystick driver
Linus Torvalds [Wed, 24 Aug 2011 16:14:42 +0000 (09:14 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: check size of FUSE_NOTIFY_INVAL_ENTRY message
fuse: mark pages accessed when written to
fuse: delete dead .write_begin and .write_end aops
fuse: fix flock
fuse: fix non-ANSI void function notation
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
bridge: fix a possible net_device leak
net: Documentation: RFC 2553bis is now RFC 3493
atm: br2684: Fix oops due to skb->dev being NULL
ipv6: Fix ipv6_getsockopt for IPV6_2292PKTOPTIONS
net: netdev-features.txt update to Documentation/networking/00-INDEX
vlan: reset headers on accel emulation path
forcedeth: call vlan_mode only if hw supports vlans
via-velocity: remove non-tagged packet filtering
bonding:reset backup and inactive flag of slave
net_sched: fix port mirror/redirect stats reporting
sit tunnels: propagate IPv6 transport class to IPv4 Type of Service
gianfar: reduce stack usage in gianfar_ethtool.c
net: minor update to Documentation/networking/scaling.txt
net: add missing entries to Documentation/networking/00-INDEX
gianfar: prevent buggy hw rx vlan tagging
net: sh_eth: Fix build by forgot including linux/interrupt.h
drivers/net/can/sja1000/plx_pci.c: eliminate double free
usbnet/cdc_ncm: Don't use stack variables for DMA
vmxnet3: Don't enable vlan filters in promiscuous mode.
iwlagn: sysfs couldn't find the priv pointer
...
Miklos Szeredi [Wed, 24 Aug 2011 08:20:17 +0000 (10:20 +0200)]
fuse: check size of FUSE_NOTIFY_INVAL_ENTRY message
FUSE_NOTIFY_INVAL_ENTRY didn't check the length of the write so the
message processing could overrun and result in a "kernel BUG at
fs/fuse/dev.c:629!"
Linus Torvalds [Wed, 24 Aug 2011 01:09:08 +0000 (18:09 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, vdso: On system call restart after SYSENTER, use int $0x80
x86, UV: Remove UV delay in starting slave cpus
x86, olpc: Wait for last byte of EC command to be accepted
H. Peter Anvin [Mon, 22 Aug 2011 20:27:06 +0000 (13:27 -0700)]
x86-32, vdso: On system call restart after SYSENTER, use int $0x80
When we enter a 32-bit system call via SYSENTER or SYSCALL, we shuffle
the arguments to match the int $0x80 calling convention. This was
probably a design mistake, but it's what it is now. This causes
errors if the system call as to be restarted.
For SYSENTER, we have to invoke the instruction from the vdso as the
return address is hardcoded. Accordingly, we can simply replace the
jump in the vdso with an int $0x80 instruction and use the slower
entry point for a post-restart.
Luciano Coelho [Tue, 23 Aug 2011 08:42:25 +0000 (11:42 +0300)]
wl12xx: add max_sched_scan_ssids value to the hw description
After commit 5a865ba, we require a separate value to indicate the
number of supported SSIDs in scheduled scans. This patch adds a
proper value to the wl12xx driver.
This fixes a regression in 3.1-rc3 where scheduled scans were not
working properly with the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ido Yariv [Mon, 22 Aug 2011 20:19:49 +0000 (23:19 +0300)]
wl12xx: Fix validation of pm_runtime_get_sync return value
wl1271_sdio_power_on checks if the return value of pm_runtime_get_sync
is non-zero, and if so bails out.
However, pm_runtime_get_sync can return a positive number which does not
suggest an error has occurred. This is problematic for two reasons:
1. The function will needlessly bail out without decrementing back the
runtime PM reference counter.
2. wl1271_power_on only checks if wl1271_power_on return value is
negative. This means that wl1271_power_on will continue even if
wl1271_sdio_power_on bailed out. As a result, sdio transactions will
be initiated without properly enabling the sdio function and claiming
the host. This could even lead to a kernel panic.
Fix this by only checking that the return value of pm_runtime_get_sync
is non-negative.
Signed-off-by: Ido Yariv <ido@wizery.com> Acked-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ido Yariv [Mon, 22 Aug 2011 20:19:48 +0000 (23:19 +0300)]
wl12xx: Remove obsolete testmode NVS push command
The testmode NVS push command is no longer in use. In addition, it has
several implementation issues that prevent it from working correctly:
1. wl1271_tm_cmd_configure relies on wl->chip.id being set. However,
since the device was not necessarily booted by the time the function
is called, wl->chip.id will be initialized to 0.
2. The NVS file is fetched by calling request_firmware() before it is
possible to push an NVS file.
3. The maximum allowed size of nl binary payloads is not sufficient for
pushing NVS files.
4. Pushing 128x NVS files will always fail due to a bug in the
validation code.
5. In case the pushed NVS file is found invalid, the mutex will be kept
locked and the nvs member will become a dangling pointer.
Since this feature is not being used, remove it completely instead of
fixing it.
Signed-off-by: Ido Yariv <ido@wizery.com> Acked-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds [Tue, 23 Aug 2011 18:41:44 +0000 (11:41 -0700)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: fix tracing builds inside the source tree
xfs: remove subdirectories
xfs: don't expect xfs headers to be in subdirectories
Linus Torvalds [Tue, 23 Aug 2011 17:46:21 +0000 (10:46 -0700)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: Extended DDC Probing for Toshiba L300D Radeon Mobility X1100 HDMI-A Connector
drm/ttm: ensure ttm for new node is bound before calling move_notify()
drm/ttm: unbind ttm before destroying node in accel move cleanup
drm/ttm: fix ttm_bo_add_ttm(user) failure path
drm/radeon: Make vramlimit parameter actually work.
drm/radeon: Explicitly print GTT/VRAM offsets on test failure.
drm/radeon: Take IH ring into account for test size calculation.
drm/radeon/alpha: Add Alpha support to Radeon DRM code
It turns out that this breaks several drivers, one example being OMAP
boards which use the on-board OMAP UARTs and the omap-serial driver that
will not boot to userspace after the commit.
Paul Walmsley reports that enabling CONFIG_DEBUG_SHIRQ reveals 'IRQ
handler type mismatch' errors:
IRQ handler type mismatch for IRQ 74
current handler: serial idle
...
and the reason is that setting IRQF_ONESHOT will now result in those
interrupt handlers having different IRQF flags, and thus being
unsharable. So the commit log in the reverted commit:
"Since it is required for those users and
there is no difference for others it makes sense to add this flag
unconditionally."
is simply not true: there may not be any difference from a "actions at
irq time", but there is a *big* difference wrt this flag testing irq
management (see __setup_irq() in kernel/irq/manage.c).
One solution may be to stop verifying IRQF_ONESHOT in __setup_irq(), but
right now the safe course of action is to revert the change. Let's
revisit this in a later merge window.
Reported-by: Paul Walmsley <paul@pwsan.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Requested-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Toshiba Satellite L300D with ATI Mobility Radeon X1100 sends data
to i2c bus for a HDMI connector that is not implemented/existent
on the notebook's board.
Fix by applying extented DDC probing for this connector.
Requires [PATCH] drm/radeon: Extended DDC Probing for Connectors
with Improperly Wired DDC Lines
Tested for kernel 2.6.38 on Toshiba Satellite L300D notebook
BugLink: http://bugs.launchpad.net/bugs/826677 Signed-off-by: Thomas Reim <reimth@gmail.com> Acked-by: Chris Routh <routhy@gmail.com> Cc: <stable@kernel.org> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
David Herrmann [Wed, 17 Aug 2011 09:43:24 +0000 (11:43 +0200)]
HID: wiimote: Add status and return request handlers
The wiimote resets the current drm when an extension is plugged in.
Fortunately, it also sends a status report in this situation so we just
reset the drm on every status report to keep the drm consistent.
Also handle return reports from the wiimote which indicate success and
failure of requests that we've sent.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
David Herrmann [Wed, 17 Aug 2011 09:43:23 +0000 (11:43 +0200)]
HID: wiimote: Add drm request
The wiimote reports data in several data reporting modes (DRM). The DRM
request makes the wiimote send data in the requested drm.
The DRM mode can be set explicitely or can be chosen by the driver. To let
the driver choose the DRM mode, pass WIIPROTO_REQ_NULL placeholder to it. This
is no valid request and is replaced with an appropriate DRM.
Currently, the driver always sets the basic DRM_K mode, but this will be
extended when further peripherals like accelerometer and IR are supported.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
David Herrmann [Wed, 17 Aug 2011 09:43:22 +0000 (11:43 +0200)]
HID: wiimote: Register led class devices
This registers 4 led devices to allow controlling the wiimote leds via standard
LED sysfs API. It removes the four sysfs attributes so we don't have two APIs
for one device.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
David Herrmann [Wed, 17 Aug 2011 09:43:20 +0000 (11:43 +0200)]
HID: wiimote: Simplify synchronization
The new locking scheme in HID core allows us to remove a bit of synchronization.
Since the HID layer acts synchronously we simply register input core last and
there are no synchonization issues anymore.
Also register sysfs files after that to simplify the code.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Ben Skeggs [Mon, 22 Aug 2011 03:15:05 +0000 (03:15 +0000)]
drm/ttm: ensure ttm for new node is bound before calling move_notify()
This was true for new TTM_PL_SYSTEM and new TTM_PL_TT cases, but wasn't
the case on TTM_PL_SYSTEM<->TTM_PL_TT moves, which causes trouble on some
paths as nouveau's move_notify() hook requires that the dma addresses be
valid at this point.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ben Skeggs [Mon, 22 Aug 2011 03:15:04 +0000 (03:15 +0000)]
drm/ttm: unbind ttm before destroying node in accel move cleanup
Nouveau makes the assumption that if a TTM is bound there will be a mm_node
around for it and the backwards ordering here resulted in a use-after-free
on some eviction paths.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Marcin Slusarz [Mon, 22 Aug 2011 21:17:57 +0000 (21:17 +0000)]
drm/ttm: fix ttm_bo_add_ttm(user) failure path
ttm_tt_destroy kfrees passed object, so we need to nullify
a reference to it.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Cc: stable@kernel.org Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jeremiah Matthey [Tue, 23 Aug 2011 07:44:30 +0000 (09:44 +0200)]
HID: usbhid: Add support for SiGma Micro chip
Patch to add SiGma Micro-based keyboards (1c4f:0002) to hid-quirks.
These keyboards dont seem to allow the records to be initialized, and hence a
timeout occurs when the usbhid driver attempts to initialize them. The patch
just adds the signature for these keyboards to the hid-quirks list with the
setting HID_QUIRK_NO_INIT_REPORTS. This removes the 5-10 second wait for the
timeout to occur.
Eric Dumazet [Mon, 22 Aug 2011 06:05:59 +0000 (06:05 +0000)]
bridge: fix a possible net_device leak
Jan Beulich reported a possible net_device leak in bridge code after
commit bb900b27a2f4 (bridge: allow creating bridge devices with netlink)
Reported-by: Jan Beulich <JBeulich@novell.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The code really requires the current source directory to be in the
header search path. We already do this if building with an object
tree separate from the source, but it needs to be added manually
if building inside the source. The cflags addition for it accidentally
got removed when collapsing the xfs directory structure.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Alex Elder <aelder@sgi.com>
Linus Torvalds [Mon, 22 Aug 2011 18:25:44 +0000 (11:25 -0700)]
Merge branch 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/tracing: Fix tracing config option properly
xen: Do not enable PV IPIs when vector callback not present
xen/x86: replace order-based range checking of M2P table by linear one
xen: xen-selfballoon.c needs more header files
David Woodhouse [Fri, 19 Aug 2011 20:14:47 +0000 (22:14 +0200)]
bcma: add uevent to the bus, to autoload drivers
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Acked-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Fix STA (AR9485) bringup issue due to incorrect MAC address
Due to some recent optimization done in the way the mac address
bytes are written into the OTP memory, some AR9485 chipsets were
forced to use the first byte from the eeprom template and the
remaining bytes are read from OTP.
AR9485 happens to use generic eeprom template which has 0x1 as
the first byte causes issues in bringing up the card.
So fixed the eeprom template accordingly to address the issue.
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: do not drop usb dev reference counter on suspend
When hibernating ->resume may not be called by usb core, but disconnect
and probe instead, so we do not increase the counter after decreasing
it in ->supend. As a result we free memory early, and get crash when
unplugging usb dongle.
Cc: stable@kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Input: ad714x - read the interrupt status registers in a row
The interrupt status registers should be read in row to avoid invalid data.
Alter "read" method for both bus options to allow reading several registers
in a row and make sure we read interrupt status registers properly.
Read sequence saves 50% of bus transactions compared to single register
reads. So use it also for the result registers, which are also located
in a row.
Also update copyright notice.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dmitry Torokhov [Mon, 22 Aug 2011 16:45:39 +0000 (09:45 -0700)]
Input: ad714x - use DMA-safe buffers for spi_write()
spi_write() requires use of DMA-safe (cacheline aligned) buffers.
Also use the same buffers when reading data since to avoid extra
locking and potential memory allocation in spi_write_then_read().
Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This change replaced the SMP operations with event based handlers without
taking into account that this only works when the hypervisor supports
callback vectors. This causes unexplainable hangs early on boot for
HVM guests with more than one CPU.
BugLink: http://bugs.launchpad.net/bugs/791850 CC: stable@kernel.org Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Tested-and-Reported-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Michel Dänzer [Fri, 19 Aug 2011 15:24:18 +0000 (15:24 +0000)]
drm/radeon: Make vramlimit parameter actually work.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Michel Dänzer [Fri, 19 Aug 2011 15:24:17 +0000 (15:24 +0000)]
drm/radeon: Explicitly print GTT/VRAM offsets on test failure.
Otherwise these would need to be painstakingly calculated looking at the source
code.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Michel Dänzer [Fri, 19 Aug 2011 15:24:16 +0000 (15:24 +0000)]
drm/radeon: Take IH ring into account for test size calculation.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
projects / linux-beck.git / log