]> git.karo-electronics.de Git - linux-beck.git/log
linux-beck.git
8 years agoARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth
Adam Ford [Wed, 16 Dec 2015 21:34:15 +0000 (15:34 -0600)]
ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth

Bindings for the WL1283 Bluetooth was removed from the shared transport
driver in commit c0bd1b9e5895 ("Revert ti-st: add device tree support")
Until we havea better binding, we need to use the platform data to
initialize Bluetooth.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: OMAP2+: LogicPD Torpedo: Add LCD Type 15 Support
Adam Ford [Thu, 17 Dec 2015 03:18:29 +0000 (21:18 -0600)]
ARM: OMAP2+: LogicPD Torpedo: Add LCD Type 15 Support

Add basic support for Logic PD type 15 display for older development kits.
This uses GPIO for the backlight.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: cm-t335: add support for bluetooth
Uri Mashiach [Sun, 13 Dec 2015 08:55:39 +0000 (10:55 +0200)]
ARM: dts: cm-t335: add support for bluetooth

bluetooth HW is WLS1271 chip connected to UART1.

Device tree modifications:
- Pinmux for UART1.
- Pinmux for bluetooth enable GPIO.

Bluetooth enable GPIO is set to enable during startup by setting the
relevant pinmux pin to pull-up.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: cm-t335: add support for DVI/LCD
Uri Mashiach [Sun, 13 Dec 2015 08:55:38 +0000 (10:55 +0200)]
ARM: dts: cm-t335: add support for DVI/LCD

Add pinmux configuration for DVI/LCD.
Add DRM display driver node with timing configurations for DVI and LCD.
Add I2C GPIOs configurations for DVI and LCD enable.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: cm-t335: add support for I2C GPIO expander
Uri Mashiach [Sun, 13 Dec 2015 08:55:37 +0000 (10:55 +0200)]
ARM: dts: cm-t335: add support for I2C GPIO expander

The I2C GPIO expander (PCA9555) adds 16 GPIOs to the module.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: cm-t335: add support for SBC-T335
Uri Mashiach [Sun, 13 Dec 2015 08:55:36 +0000 (10:55 +0200)]
ARM: dts: cm-t335: add support for SBC-T335

Add basic support for the SBC-T335.

CompuLab SBC-T335 is a single baseboard computer.
The SBC-T335 is based on the Texas Instruments Cortex-A8 Sitara AM3354
SoC.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: cm-t335: add support for USB0
Ilya Ledvich [Sun, 13 Dec 2015 08:55:35 +0000 (10:55 +0200)]
ARM: dts: cm-t335: add support for USB0

Enable USB0.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap: replace legacy *,wakeup property with wakeup-source
Sudeep Holla [Wed, 21 Oct 2015 10:10:12 +0000 (11:10 +0100)]
ARM: dts: omap: replace legacy *,wakeup property with wakeup-source

Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" boolean property to enable the wakeup
source, "wakeup-source" is the new standard binding.

This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.

Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am335x: replace gpio-key,wakeup with wakeup-source property
Sudeep Holla [Wed, 21 Oct 2015 10:10:06 +0000 (11:10 +0100)]
ARM: dts: am335x: replace gpio-key,wakeup with wakeup-source property

Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.

This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.

Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: DTS: am437x: Use the new DT bindings for the eDMA3
Peter Ujfalusi [Thu, 17 Dec 2015 13:33:37 +0000 (15:33 +0200)]
ARM: DTS: am437x: Use the new DT bindings for the eDMA3

Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: DTS: am33xx: Use the new DT bindings for the eDMA3
Peter Ujfalusi [Thu, 17 Dec 2015 13:33:36 +0000 (15:33 +0200)]
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3

Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoMerge commit 'ae0add740cd06169cd124f9aaa6eceb11e5b3060' into omap-for-v4.5/dt
Tony Lindgren [Thu, 17 Dec 2015 17:41:18 +0000 (09:41 -0800)]
Merge commit 'ae0add740cd06169cd124f9aaa6eceb11e5b3060' into omap-for-v4.5/dt

8 years agodmaengine: edma: DT: Change reserved slot array from 16bit to 32bit type
Peter Ujfalusi [Wed, 9 Dec 2015 08:18:11 +0000 (10:18 +0200)]
dmaengine: edma: DT: Change reserved slot array from 16bit to 32bit type

This change makes the DT file to be easier to read since the reserved slots
array does not need the '/bits/ 16' to be specified, which might confuse
some people.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
8 years agodmaengine: edma: DT: Change memcpy channel array from 16bit to 32bit type
Peter Ujfalusi [Wed, 9 Dec 2015 08:18:10 +0000 (10:18 +0200)]
dmaengine: edma: DT: Change memcpy channel array from 16bit to 32bit type

This change makes the DT file to be easier to read since the memcpy
channels array does not need the '/bits/ 16' to be specified, which might
confuse some people.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
8 years agoARM: dts: omap3-igep0030: Use MMC pwrseq to init SDIO WiFi
Javier Martinez Canillas [Thu, 3 Dec 2015 18:02:09 +0000 (15:02 -0300)]
ARM: dts: omap3-igep0030: Use MMC pwrseq to init SDIO WiFi

When the WiFi support was added to the IGEP0030 board, the MMC subsystem
did not provide a mechanism to define power sequence providers. So a DT
hack was used to toggle the WiFi chip reset and power down pins by using
fake fixed regulators whose enable GPIO was the GPIOs connected to these
pins.

But now the simple MMC power sequence provider can be used for this and
the workaround removed.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap3-igep0020: Use MMC pwrseq to init SDIO WiFi
Javier Martinez Canillas [Thu, 3 Dec 2015 18:02:08 +0000 (15:02 -0300)]
ARM: dts: omap3-igep0020: Use MMC pwrseq to init SDIO WiFi

When the WiFi support was added to the IGEP0020 board, the MMC subsystem
did not provide a mechanism to define power sequence providers. So a DT
hack was used to toggle the WiFi chip reset and power down pins by using
fake fixed regulators whose enable GPIO was the GPIOs connected to these
pins.

But now the simple MMC power sequence provider can be used for this and
the workaround removed.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: cl-som-am57x: skip resetting ETH PHYs
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:21 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: skip resetting ETH PHYs

ETH PHYs setup on CL-SOM-AM57X is established in U-Boot along with
bringing them out of reset. This is done by toggling GPIOs belonging
to GPIO2/3 controllers on AM57xx.

Skip resetting ETH PHYs, by adding "ti,no-reset-on-init" to GPIO2/3
controllers DT nodes.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: sbc-am57x: add HDMI support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:20 +0000 (20:03 +0200)]
ARM: dts: am57xx: sbc-am57x: add HDMI support

Add HDMI video output support.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: compulab-sb-som: add HDMI connector
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:19 +0000 (20:03 +0200)]
ARM: dts: am57xx: compulab-sb-som: add HDMI connector

Add HDMI connector node without a valid input endpoint.

CompuLab SB-SOM is a carrier board, hence the endpoint
should be added in the board DT with a valid HDMI output.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: sbc-am57x: add LCD support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:18 +0000 (20:03 +0200)]
ARM: dts: am57xx: sbc-am57x: add LCD support

Startek-kd050c 800x480 LCD panel timings are described in
compulab-sb-som.dtsi.

Add appropriate DT endpoints to connect DPI output and LCD.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: sbc-am57x: add GPIO expander support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:17 +0000 (20:03 +0200)]
ARM: dts: am57xx: sbc-am57x: add GPIO expander support

Add PCA9555 GPIO expander support (over I2C5 bus).

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: sbc-am57x: add EEPROM support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:16 +0000 (20:03 +0200)]
ARM: dts: am57xx: sbc-am57x: add EEPROM support

On-board EEPROM chip is used for storing a board production info.

Add carrier board EEPROM support (over I2C5 bus).

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: sbc-am57x: add usb vbus pinmux
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:15 +0000 (20:03 +0200)]
ARM: dts: am57xx: sbc-am57x: add usb vbus pinmux

usb1_drvvbus pin is used to Drive-VBUS enable to external charge
pump/power switch.

Add a pinmux for that pin.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: cl-som-am57x: add MMC1 support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:14 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: add MMC1 support

Add MMC1 support, used for SD/MMC card.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: sbc-am57x: add basic board support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:13 +0000 (20:03 +0200)]
ARM: dts: am57xx: sbc-am57x: add basic board support

SBC-AM57x is a single board computer designed for industrial and
embedded applications. It is based on the Texas Instruments Sitara AM57x
system-on-chip family. SBC-AM57x is implemented with the CL-SOM-AM57x
computer-on-module providing most of the functions, and SB-SOM-AM57x
carrier board providing additional peripheral functions and connectors.

https://www.compulab.co.il/products/sbcs/sbc-am57x-ti-am5728-am5718-single-board-computer/

https://www.compulab.co.il/products/computer-on-modules/cl-som-am57x-ti-am5728-am5718-system-on-module/

Add basic board support, including UART3, used as a serial console.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: cl-som-am57x: add analog audio support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:12 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: add analog audio support

Add analog audio DT nodes:

1. simple-audio-card node
2. wm8731 codec node
3. MCASP3 pinmux

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: cl-som-am57x: add touchscreen support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:11 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: add touchscreen support

Add ADS7846 touchscreen support.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: cl-som-am57x: add USB support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:10 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: add USB support

Add USB support.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: cl-som-am57x: add dual EMAC support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:09 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: add dual EMAC support

Add dual EMAC support.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: cl-som-am57x: add spi-flash support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:08 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: add spi-flash support

On-board spi-flash chip is used as a main boot device.
Add spi-flash chip support (over QSPI bus).

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: cl-som-am57x: add eMMC support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:07 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: add eMMC support

CM-SOM-AM57X has two options of main storage devices - eMMC or NAND.
Add eMMC chip support (over MMC2 bus).

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: cl-som-am57x: add EEPROM support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:06 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: add EEPROM support

On-board EEPROM chip is used for storing a board production
info.

Add module EEPROM support (over I2C4 bus).

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: cl-som-am57x: add I2C3 support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:05 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: add I2C3 support

Enable I2C3 bus and add appropriate pinmux.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: cl-som-am57x: dts: add RTC support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:04 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: dts: add RTC support

Add EM3027 RTC chip support (over I2C4 bus).

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx: cl-som-am57x: add basic module support
Dmitry Lifshitz [Tue, 1 Dec 2015 18:03:03 +0000 (20:03 +0200)]
ARM: dts: am57xx: cl-som-am57x: add basic module support

Add support for CompuLab CM-SOM-AM57X board.

CL-SOM-AM57x is a miniature System-on-Module (SoM) based on
TI Sitara AM57x ARM Cortex-A15 System-on-Chip family.

https://www.compulab.co.il/products/computer-on-modules/cl-som-am57x-ti-am5728-am5718-system-on-module/

Add basic DT support for standalone module (without a carrier board):

* Memory configuration
* Heartbeat led
* I2C1 and I2C4
* PMIC
* SATA

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add lcd support
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:09 +0000 (15:55 +0200)]
ARM: dts: am437x: cm-t43: add lcd support

Add the necessary dss configuration to drive the startek lcd on CompuLab
sbc-t43 single board computer.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add support for mmc1
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:08 +0000 (15:55 +0200)]
ARM: dts: am437x: cm-t43: add support for mmc1

On SBC-T43 the mmc1 interface is connected to an SD-Card slot.
Add the necessary muxing and configuration to the device tree.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: sb-som: introduce SB-SOM baseboard
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:07 +0000 (15:55 +0200)]
ARM: dts: sb-som: introduce SB-SOM baseboard

CompuLab SB-SOM baseboard is a carrier board for multiple arm-based SoMs.
It currently supports (with minor adjustments to assembly) CM-T43, CM-T54,
and CM-QS600 modules. It is a building block in the SBC-T43 single board
computer, which consists of cm-t43 on top of sb-som-t43.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add support for baseboard eeprom
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:06 +0000 (15:55 +0200)]
ARM: dts: am437x: cm-t43: add support for baseboard eeprom

SB-SOM baseboard comes with an on-board EEPROM. On SBC-T43 this EEPROM
resides on the i2c1 bus. Add it to the device tree.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add pca9555 support
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:05 +0000 (15:55 +0200)]
ARM: dts: am437x: cm-t43: add pca9555 support

SB-SOM comes with a PCA9555 GPIO extender. On SBC-T43 this resides on the
i2c1 bus. Add it to the device tree.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add touchscreen support
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:04 +0000 (15:55 +0200)]
ARM: dts: am437x: cm-t43: add touchscreen support

AM437x has an internal touchscreen controller. Add support for it
on cm-t43.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add eMMC support
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:03 +0000 (15:55 +0200)]
ARM: dts: am437x: cm-t43: add eMMC support

One of the CompuLab cm-t43 configurations comes with on-board eMMC as
primary storage, residing on the mmc2 interface. Add it to the device tree.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add USB support
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:02 +0000 (15:55 +0200)]
ARM: dts: am437x: cm-t43: add USB support

Add USB support for CompuLab sbc-t43 single board computer,
defaulting to host mode.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add dual emac support
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:01 +0000 (15:55 +0200)]
ARM: dts: am437x: cm-t43: add dual emac support

CM-T43 comes with 2 ethernet ports connected to the cpsw subsystem, which
has 2 modes of operation: switch mode and dual emac mode.
Add the relevant muxing and set it up to work in dual emac mode by
default.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add NAND support
Nikita Kiryanov [Tue, 1 Dec 2015 13:55:00 +0000 (15:55 +0200)]
ARM: dts: am437x: cm-t43: add NAND support

One of the CompuLab cm-t43 configurations comes with on-board NAND flash as
primary storage. It is partitioned into kernel, dtb, and rootfs partitions.
Add it to the device tree.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add spi-flash support
Nikita Kiryanov [Tue, 1 Dec 2015 13:54:59 +0000 (15:54 +0200)]
ARM: dts: am437x: cm-t43: add spi-flash support

CM-T43 has an on-board 2MB SPI-flash which stores U-Boot and the U-Boot
environment. Add it to the device tree.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add PMIC support.
Nikita Kiryanov [Tue, 1 Dec 2015 13:54:58 +0000 (15:54 +0200)]
ARM: dts: am437x: cm-t43: add PMIC support.

Add PMIC support for CompuLab cm-t43 module. For now we keep all regulators
enabled until this could be refined with power management support.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add support for module eeprom
Nikita Kiryanov [Tue, 1 Dec 2015 13:54:57 +0000 (15:54 +0200)]
ARM: dts: am437x: cm-t43: add support for module eeprom

CM-T43 has an on-board EEPROM on i2c bus 0. Add it to the device tree.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x: cm-t43: add basic support for sbc-t43
Nikita Kiryanov [Tue, 1 Dec 2015 13:54:56 +0000 (15:54 +0200)]
ARM: dts: am437x: cm-t43: add basic support for sbc-t43

Add basic support for SBC-T43: a CM-T43 based single board computer.
CM-T43 is an AM437x based System-on-Module designed to serve as a building
block in embedded applications. SBC-T43 is composed of CM-T43 module on
top of the SB-SOM-T43 baseboard.
Basic support includes UART, GPIO, and I2C.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: dra72-evm: Mark uart1 rxd as wakeup capable
Vignesh R [Thu, 26 Nov 2015 08:31:26 +0000 (14:01 +0530)]
ARM: dts: dra72-evm: Mark uart1 rxd as wakeup capable

Uart1 rxd  is wakeup capable on DRA72 EVM. Hence, mark rxd line as
wakeup capable. This is similar to commit 66b0436977e2c ("ARM: dts:
dra7-evm: Mark uart1 rxd as wakeup capable") for DRA74 EVM.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am4372: add spi alias for qspi
Mugunthan V N [Thu, 19 Nov 2015 07:01:02 +0000 (12:31 +0530)]
ARM: dts: am4372: add spi alias for qspi

Set the alias for qspi to spi0

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: dra7: add spi alias for qspi
Mugunthan V N [Thu, 19 Nov 2015 07:01:01 +0000 (12:31 +0530)]
ARM: dts: dra7: add spi alias for qspi

Set the alias for qspi to spi0

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoarm, am335x: add support for the bosch shc board
Heiko Schocher [Tue, 17 Nov 2015 08:24:15 +0000 (09:24 +0100)]
arm, am335x: add support for the bosch shc board

add support for the am335x based shc board.

UART: 0-2 and 4
DRAM: 512 MiB
MMC:  OMAP SD/MMC: 0 @ 26 MHz
      OMAP SD/MMC: 1 @ 26 MHz
I2C:  at24 eeprom, pcf8563
USB:  USB1 (host)

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap4: Add elm node
Franklin S Cooper Jr [Wed, 28 Oct 2015 21:02:16 +0000 (16:02 -0500)]
ARM: dts: omap4: Add elm node

Add device tree entry for the error location module.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoregulator: tps65217: remove tps65217.dtsi file
Heiko Schocher [Tue, 27 Oct 2015 12:36:36 +0000 (13:36 +0100)]
regulator: tps65217: remove tps65217.dtsi file

remove tps65217.dtsi and adapt all boards, which
used it.

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: cm-t335: add support for PWM backlight
Ilya Ledvich [Tue, 24 Nov 2015 14:02:13 +0000 (16:02 +0200)]
ARM: dts: cm-t335: add support for PWM backlight

Add pinmux configuration for ECAP0 pin.
Add node for PWM backlight device.
Use PWM output from ecap0 as backlight source.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: cm-t335: add support for network device
Ilya Ledvich [Tue, 24 Nov 2015 14:02:12 +0000 (16:02 +0200)]
ARM: dts: cm-t335: add support for network device

Add pinmux configurations for RGMII1 based CPSW Ethernet pins and
MDIO pins:
 - default configuration required for module in active state,
 - sleep configuration required for module in inactive state.
Add mac node with single slave device. Add nodes for davinci_mdio and
cpsw_emac0.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: cm-t335: add support for MMC
Ilya Ledvich [Tue, 24 Nov 2015 14:02:11 +0000 (16:02 +0200)]
ARM: dts: cm-t335: add support for MMC

Add pinmux configuration for MMC0 pins.
Add fixed regulator 'vmmc_fixed'.
Enable MMC0 in 4-bit mode.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: cm-t335: add support for NAND flash
Ilya Ledvich [Tue, 24 Nov 2015 14:02:10 +0000 (16:02 +0200)]
ARM: dts: cm-t335: add support for NAND flash

Add pinmux configuration for NAND specific GPMC pins.
Add description for GPMC controller. Add child node for NAND flash
including CM-T335 specific partition table to GPMC node.
Enable error-location module (ELM).

Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: cm-t335: add basic support for I2C
Ilya Ledvich [Tue, 24 Nov 2015 14:02:09 +0000 (16:02 +0200)]
ARM: dts: cm-t335: add basic support for I2C

Add pinmux configuration for I2C0 and I2C1 pins.
Add description for I2C0 bus, set clock frequency to 400kHz.
Add child nodes for 24c02 EEPROM and em3027 RTC on I2C0 bus.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: cm-t335: add initial support
Ilya Ledvich [Tue, 24 Nov 2015 14:02:08 +0000 (16:02 +0200)]
ARM: dts: cm-t335: add initial support

Add basic support for CompuLab cm-t335 module based on AM335X SoC.

CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM)
The module is built around the Texas Instruments Sitara AM3352/4
system-on-chip.

The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board
NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit
Ethernet, CAN bus.

Current patch adds support:
UART0 and GPIO LED

Detailed description can be found at the module site:
http://www.compulab.co.il/products/computer-on-modules/cm-t335/

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
[uri.mashiach@compulab.co.il: the default RAM amount reduced to
128MB to support also the minimal module configuration]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: Set VAUX1 and VAUX4 on Logic PD Torpedo
Adam Ford [Mon, 26 Oct 2015 12:53:10 +0000 (07:53 -0500)]
ARM: dts: Set VAUX1 and VAUX4 on Logic PD Torpedo

The schematic expects VAUX1 to be 3.0V attached to the debug port.
The schematic expects VAUX4 to be 1.8V.
VAUX4 powers VDDS_CSI2 on processor.

Signed-off-by: Adam Ford <adam.ford@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: Change I2C2 and I2C3 to 400KHz for LogicPD Torpedo DM3730 devkit
Adam Ford [Mon, 26 Oct 2015 12:42:38 +0000 (07:42 -0500)]
ARM: dts: Change I2C2 and I2C3 to 400KHz for LogicPD Torpedo DM3730 devkit

When used with the Logic PD development kit, this makes the I2C buses match
the BSP released by Logic PD.

Signed-off-by: Adam Ford <adam.ford@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: Enable UART2 pinctrl on LogicPD Torpedo + Wireless module
Adam Ford [Mon, 26 Oct 2015 12:27:37 +0000 (07:27 -0500)]
ARM: dts: Enable UART2 pinctrl on LogicPD Torpedo + Wireless module

Setup UART2 for communication at 3MBps with flow control.

Signed-off-by: Adam Ford <adam.ford@logicpd.com>
[tony@atomide.com: dropped the kim changes, that binding has been removed]
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: Set VAUX1 and VAUX4 to 3.0V and 1.8V respectively
Adam Ford [Fri, 23 Oct 2015 12:27:33 +0000 (07:27 -0500)]
ARM: dts: Set VAUX1 and VAUX4 to 3.0V and 1.8V respectively

The development kit schematic expects VAUX1 to be 3.0V.  Most users use the development kit as a reference.
The development kit schematic expects VAUX4 to be 1.8V.  VAUX4 powers VDDS_CSI2 on processor.  If the voltage is too high it could damage the processor.
If it's too low, it won't work.

Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: Change I2C2 and I2C3 to 400KHz for LogicPD Torpedo DM3730 devkit
Adam Ford [Fri, 23 Oct 2015 12:23:14 +0000 (07:23 -0500)]
ARM: dts: Change I2C2 and I2C3 to 400KHz for LogicPD Torpedo DM3730 devkit

When used with the Logic PD development kit, this makes the I2C buses match
the BSP released by Logic PD.

Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: Add audio support for LogicPD Torpedo DM3730 devkit
Adam Ford [Fri, 23 Oct 2015 12:20:23 +0000 (07:20 -0500)]
ARM: dts: Add audio support for LogicPD Torpedo DM3730 devkit

Use the TWL4030 Codec with mcbsp2 on Torpedo.

Signed-off-by: Adam Ford <adam.ford@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x/am33xx/omap/dm816x: Add gpmc dma channel
Franklin S Cooper Jr [Thu, 15 Oct 2015 17:37:27 +0000 (12:37 -0500)]
ARM: dts: am437x/am33xx/omap/dm816x: Add gpmc dma channel

Add dma channel information to the gpmc. Although not enabled by
default this will allow prefetch-dma to be used.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: Add omap4-hwspinlock support in dm816x
Neil Armstrong [Thu, 12 Nov 2015 14:07:49 +0000 (15:07 +0100)]
ARM: dts: Add omap4-hwspinlock support in dm816x

Add dm816x DT entries for omap4-hwspinlock support as hwmod spinbox.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: remove dm816x invalid DT l3_main hwmod
Neil Armstrong [Thu, 12 Nov 2015 14:07:45 +0000 (15:07 +0100)]
ARM: dts: remove dm816x invalid DT l3_main hwmod

Remove invalid l3_main hwmod entry from dm816x DT ocp node.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: add dm816x pwm property to timers
Neil Armstrong [Thu, 12 Nov 2015 14:07:40 +0000 (15:07 +0100)]
ARM: dts: add dm816x pwm property to timers

Adds ti,timer-pwm property to timers 4 to 7 to permit usage of their
PWM output fonctionnality via the dmtimer driver.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am335x-boneblack: Use pinctrl constants and AM33XX_IOPAD macro
Andrew F. Davis [Fri, 13 Nov 2015 16:47:27 +0000 (10:47 -0600)]
ARM: dts: am335x-boneblack: Use pinctrl constants and AM33XX_IOPAD macro

Using constants for pinctrl allows better readability and removes
redundancy with comments. AM33XX_IOPAD allows us to use part of the
pinctrl physical address as in the TRM instead of an offset.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap5-uevm.dts: Use OMAP5_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:17 +0000 (01:54 -0300)]
ARM: dts: omap5-uevm.dts: Use OMAP5_IOPAD pinmux macro

Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap5-cm-t54: Use OMAP5_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:16 +0000 (01:54 -0300)]
ARM: dts: omap5-cm-t54: Use OMAP5_IOPAD pinmux macro

Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap5-board-common: Use OMAP5_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:15 +0000 (01:54 -0300)]
ARM: dts: omap5-board-common: Use OMAP5_IOPAD pinmux macro

Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: twl6030: Use OMAP4_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:14 +0000 (01:54 -0300)]
ARM: dts: twl6030: Use OMAP4_IOPAD pinmux macro

Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap4-sdp-es23plus: Use OMAP4_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:13 +0000 (01:54 -0300)]
ARM: dts: omap4-sdp-es23plus: Use OMAP4_IOPAD pinmux macro

Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap4-sdp: Use OMAP4_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:12 +0000 (01:54 -0300)]
ARM: dts: omap4-sdp: Use OMAP4_IOPAD pinmux macro

Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap4-panda-es: Use OMAP4_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:11 +0000 (01:54 -0300)]
ARM: dts: omap4-panda-es: Use OMAP4_IOPAD pinmux macro

Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap4-panda-common: Use OMAP4_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:10 +0000 (01:54 -0300)]
ARM: dts: omap4-panda-common: Use OMAP4_IOPAD pinmux macro

Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap4-panda-a4: Use OMAP4_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:09 +0000 (01:54 -0300)]
ARM: dts: omap4-panda-a4: Use OMAP4_IOPAD pinmux macro

Use the pinmux IOPAD macros to define the register as an offset from
the padconf physical address instead of the offset from padconf base.
This makes the DTS easier to read since matches the addresses listed
in the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: twl4030: Use OMAP3_CORE1_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:08 +0000 (01:54 -0300)]
ARM: dts: twl4030: Use OMAP3_CORE1_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap3-zoom3: Use OMAP3_*_IOPAD pinmux macros
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:07 +0000 (01:54 -0300)]
ARM: dts: omap3-zoom3: Use OMAP3_*_IOPAD pinmux macros

Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap3-n9: Use OMAP3_CORE1_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:06 +0000 (01:54 -0300)]
ARM: dts: omap3-n9: Use OMAP3_CORE1_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap3-n900: Use OMAP3_CORE1_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:05 +0000 (01:54 -0300)]
ARM: dts: omap3-n900: Use OMAP3_CORE1_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap3-ldp: Use OMAP3_CORE1_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:04 +0000 (01:54 -0300)]
ARM: dts: omap3-ldp: Use OMAP3_CORE1_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap3-evm-37xx: Use OMAP3_*_IOPAD pinmux macros
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:03 +0000 (01:54 -0300)]
ARM: dts: omap3-evm-37xx: Use OMAP3_*_IOPAD pinmux macros

Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap3-beagle-xm: Use OMAP3_*_IOPAD pinmux macros
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:02 +0000 (01:54 -0300)]
ARM: dts: omap3-beagle-xm: Use OMAP3_*_IOPAD pinmux macros

Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: omap3-beagle: Use OMAP3_*_IOPAD pinmux macros
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:01 +0000 (01:54 -0300)]
ARM: dts: omap3-beagle: Use OMAP3_*_IOPAD pinmux macros

Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: dra72-evm: Use DRA7XX_CORE_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:54:00 +0000 (01:54 -0300)]
ARM: dts: dra72-evm: Use DRA7XX_CORE_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: dra7-evm: Use DRA7XX_CORE_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:53:59 +0000 (01:53 -0300)]
ARM: dts: dra7-evm: Use DRA7XX_CORE_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am57xx-beagle-x15: Use DRA7XX_CORE_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:53:58 +0000 (01:53 -0300)]
ARM: dts: am57xx-beagle-x15: Use DRA7XX_CORE_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am43x-epos-evm: Use AM4372_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:53:57 +0000 (01:53 -0300)]
ARM: dts: am43x-epos-evm: Use AM4372_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x-sk-evm: Use AM4372_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:53:56 +0000 (01:53 -0300)]
ARM: dts: am437x-sk-evm: Use AM4372_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x-idk-evm: Use AM4372_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:53:55 +0000 (01:53 -0300)]
ARM: dts: am437x-idk-evm: Use AM4372_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am437x-gp-evm: Use AM4372_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:53:54 +0000 (01:53 -0300)]
ARM: dts: am437x-gp-evm: Use AM4372_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am3517-craneboard: Use OMAP3_CORE1_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:53:53 +0000 (01:53 -0300)]
ARM: dts: am3517-craneboard: Use OMAP3_CORE1_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am335x-wega: Use AM33XX_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:53:52 +0000 (01:53 -0300)]
ARM: dts: am335x-wega: Use AM33XX_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am335x-phycore-som: Use AM33XX_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:53:51 +0000 (01:53 -0300)]
ARM: dts: am335x-phycore-som: Use AM33XX_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
8 years agoARM: dts: am335x-pepper: Use AM33XX_IOPAD pinmux macro
Javier Martinez Canillas [Fri, 13 Nov 2015 04:53:50 +0000 (01:53 -0300)]
ARM: dts: am335x-pepper: Use AM33XX_IOPAD pinmux macro

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>