Alexey Dobriyan [Thu, 29 Mar 2007 19:22:40 +0000 (12:22 -0700)]
NET: Fix sock_attach_fd() failure in sys_accept()
[NET]: Correct accept(2) recovery after sock_attach_fd()
* d_alloc() in sock_attach_fd() fails leaving ->f_dentry of new file NULL
* bail out to out_fd label, doing fput()/__fput() on new file
* but __fput() assumes valid ->f_dentry and dereferences it
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Miller [Thu, 29 Mar 2007 19:16:27 +0000 (12:16 -0700)]
VIDEO: Fix FFB DAC revision probing
[VIDEO] ffb: Fix two DAC handling bugs.
The determination of whether the DAC has inverted cursor logic is
broken, import the version checks the X.org driver uses to fix this.
Next, when we change the timing generator, borrow code from X.org that
does 10 NOP reads of the timing generator register afterwards to make
sure the video-enable transition occurs cleanly.
Finally, use macros for the DAC registers and fields in order to
provide documentation for the next person who reads this code.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We were only checking if there was enough space to put the int, but
left len as specified by the (malicious) user, sigh, fix it by setting
len to sizeof(val) and transfering just one int worth of data, the one
asked for.
Also check for negative len values.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
G. Liakhovetski [Tue, 27 Mar 2007 02:07:40 +0000 (19:07 -0700)]
PPP: Fix PPP skb leak
[PPP]: Don't leak an sk_buff on interface destruction.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Miller [Tue, 27 Mar 2007 01:56:59 +0000 (18:56 -0700)]
IPV6: Fix ipv6 round-robin locking.
[IPV6]: Fix routing round-robin locking.
As per RFC2461, section 6.3.6, item #2, when no routers on the
matching list are known to be reachable or probably reachable we
do round robin on those available routes so that we make sure
to probe as many of them as possible to detect when one becomes
reachable faster.
Each routing table has a rwlock protecting the tree and the linked
list of routes at each leaf. The round robin code executes during
lookup and thus with the rwlock taken as a reader. A small local
spinlock tries to provide protection but this does not work at all
for two reasons:
1) The round-robin list manipulation, as coded, goes like this (with
read lock held):
walk routes finding head and tail
spin_lock();
rotate list using head and tail
spin_unlock();
While one thread is rotating the list, another thread can
end up with stale values of head and tail and then proceed
to corrupt the list when it gets the lock. This ends up causing
the OOPS in fib6_add() later onthat many people have been hitting.
2) All the other code paths that run with the rwlock held as
a reader do not expect the list to change on them, they
expect it to remain completely fixed while they hold the
lock in that way.
So, simply stated, it is impossible to implement this correctly using
a manipulation of the list without violating the rwlock locking
semantics.
Reimplement using a per-fib6_node round-robin pointer. This way we
don't need to manipulate the list at all, and since the round-robin
pointer can only ever point to real existing entries we don't need
to perform any locking on the changing of the round-robin pointer
itself. We only need to reset the round-robin pointer to NULL when
the entry it is pointing to is removed.
The idea is from Thomas Graf and it is very similar to how this
was implemented before the advanced router selection code when in.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 27 Mar 2007 01:15:37 +0000 (18:15 -0700)]
NET_SCHED: Fix ingress qdisc locking.
[NET_SCHED]: Fix ingress locking
Ingress queueing uses a seperate lock for serializing enqueue operations,
but fails to properly protect itself against concurrent changes to the
qdisc tree. Use queue_lock for now since the real fix it quite intrusive.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
cls_basic doesn't allocate tp->root before it is linked into the
active classifier list, resulting in a NULL pointer dereference
when packets hit the classifier before its ->change function is
called.
Reported by Chris Madden <chris@reflexsecurity.com>
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefan Richter [Sun, 25 Mar 2007 19:24:43 +0000 (21:24 +0200)]
ieee1394: dv1394: fix CardBus card ejection
Fix NULL pointer dereference on hot ejection of a FireWire card while
dv1394 was loaded. http://bugzilla.kernel.org/show_bug.cgi?id=7121
I did not test card ejection with open /dev/dv1394 files yet.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently we have a confused udelay implementation.
* __const_udelay does not accept usecs but xloops in i386 and x86_64
* our implementation requires usecs as arg
* it gets a xloops count when called by asm/arch/delay.h
Bugs related to this (extremely long shutdown times) where reported by some
x86_64 users, especially using Device Mapper.
To hit this bug, a compile-time constant time parameter must be passed - that's
why UML seems to work most times.
Fix this with a simple udelay implementation.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jeff Dike [Sun, 25 Mar 2007 17:01:44 +0000 (13:01 -0400)]
UML - use correct register file size everywhere
This patch uses MAX_REG_NR consistently to refer to the register file
size. FRAME_SIZE isn't sufficient because on x86_64, it is smaller
than the ptrace register file size. MAX_REG_NR was introduced as a
consistent way to get the number of registers, but wasn't used
everywhere it should be.
When this causes a problem, it makes PTRACE_SETREGS fail on x86_64
because of a corrupted segment register value in the known-good
register file. The patch also adds a register dump at that point in
case there are any future problems here.
Signed-off-by: Jeff Dike <jdike@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jeff Dike [Sun, 25 Mar 2007 16:54:32 +0000 (12:54 -0400)]
UML - Fix static linking
During a static link, ld has started putting a .note section in the
.uml.setup.init section. This has the result that the UML setups
begin with 32 bytes of garbage and UML crashes immediately on boot.
This patch creates a specific .note section for ld to drop this stuff
into.
Signed-off-by: Jeff Dike <jdike@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jeff Dike [Fri, 23 Mar 2007 19:37:30 +0000 (15:37 -0400)]
UML - host VDSO fix
This fixes a problem seen by a number of people running UML on newer host
kernels. init would hang with an infinite segfault loop.
It turns out that the host kernel was providing a AT_SYSINFO_EHDR of
0xffffe000, which faked UML into believing that the host VDSO page could be
reused. However, AT_SYSINFO pointed into the middle of the address space, and
was unmapped as a result. Because UML was providing AT_SYSINFO_EHDR and
AT_SYSINFO to its own processes, these would branch to nowhere when trying to
use the VDSO.
The fix is to also check the location of AT_SYSINFO when deciding whether to
use the host's VDSO.
Signed-off-by: Jeff Dike <jdike@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Robert Hancock [Thu, 22 Mar 2007 16:39:04 +0000 (12:39 -0400)]
sata_nv: delay on switching between NCQ and non-NCQ commands
sata_nv: delay on switching between NCQ and non-NCQ commands
This patch appears to solve some problems with commands timing out in
cases where an NCQ command is immediately followed by a non-NCQ command
(or possibly vice versa). This is a rather ugly solution, but until we
know more about why this is needed, this is about all we can do.
[backport to 2.6.20 by Chuck Ebbert <cebbert@redhat.com>]
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Cc: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Albert Lee [Wed, 21 Mar 2007 20:08:08 +0000 (16:08 -0400)]
ide: clear bmdma status in ide_intr() for ICHx controllers (revised #4)
ide: clear bmdma status in ide_intr() for ICHx controllers (revised #4)
patch 1/2 (revised):
- Fix drive->waiting_for_dma to work with CDB-intr devices.
- Do the dma status clearing in ide_intr() and add a new
hwif->ide_dma_clear_irq for Intel ICHx controllers.
Revised per Alan, Sergei and Bart's advice.
Patch against 2.6.20-rc6. Tested ok on my ICH4 and pdc20275 adapters.
Please review/apply, thanks.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Adam Hawks <awhawks@us.ibm.com> Cc: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kai Makisara [Mon, 19 Mar 2007 23:58:57 +0000 (16:58 -0700)]
st: fix Tape dies if wrong block size used, bug 7919
[SCSI] st: fix Tape dies if wrong block size used, bug 7919
On Thu, 1 Feb 2007, Andrew Morton wrote:
> On Thu, 1 Feb 2007 15:34:29 -0800
> bugme-daemon@bugzilla.kernel.org wrote:
>
> > http://bugzilla.kernel.org/show_bug.cgi?id=7919
> >
> > Summary: Tape dies if wrong block size used
> > Kernel Version: 2.6.20-rc5
> > Status: NEW
> > Severity: normal
> > Owner: scsi_drivers-other@kernel-bugs.osdl.org
> > Submitter: dmartin@sccd.ctc.edu
> >
> >
> > Most recent kernel where this bug did *NOT* occur: 2.6.17.14
> >
> > Other Kernels Tested and Results:
> >
> > OK 2.6.15.7
> > OK 2.6.16.37
> > OK 2.6.17.14
> > BAD 2.6.18.6
> > BAD 2.6.18-1.2869.fc6
> > BAD 2.6.19.2 +
> > BAD 2.6.20-rc5
> >
> > NOTE: 2.6.18-1.2869.fc6 is a Fedora modified kernel, all others are from kernel.org
> >
...
> > Steps to reproduce:
> > Get a Adaptec AHA-2940U/UW/D / AIC-7881U card and a tape drive,
> > install a recent kernel
> > set the tape block size - mt setblk 4096
> > read from or write to tape using wrong block size - tar -b 7 -cvf /dev/tape foo
> >
Write does not trigger this bug because the driver refuses in fixed block
mode writes that are not a multiple of the block size. Read does trigger
it in my system.
The bug is not associated with any specific HBA. st tries to do direct i/o
in fixed block mode with reads that are not a multiple of tape block size.
The patch in this message fixes the st problem by switching to using the
driver buffer up to the next close of the device file in fixed block mode
if the user asks for a read like this.
I don't know why the bug has surfaced only after 2.6.17 although the st
problem is old. There may be another bug in the block subsystem and this
patch works around it. However, the patch fixes a problem in st and in
this way it is a valid fix.
This patch may also fix the bug 7900.
The patch compiles and is lightly tested.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jeff Dike [Mon, 19 Mar 2007 20:12:50 +0000 (16:12 -0400)]
UML - arch_prctl should set thread fs
x86_64 needs some TLS fixes. What was missing was remembering the child
thread id during clone and stuffing it into the child during each context
switch.
The %fs value is stored separately in the thread structure since the host
controls what effect it has on the actual register file. The host also needs
to store it in its own thread struct, so we need the value kept outside the
register file.
arch_prctl_skas was fixed to call PTRACE_ARCH_PRCTL appropriately. There is
some saving and restoring of registers in the ARCH_SET_* cases so that the
correct set of registers are changed on the host and restored to the process
when it runs again.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Zach Brown [Sun, 18 Mar 2007 22:55:51 +0000 (18:55 -0400)]
dio: invalidate clean pages before dio write
This patch fixes a user-triggerable oops that was reported by Leonid
Ananiev as archived at http://lkml.org/lkml/2007/2/8/337.
dio writes invalidate clean pages that intersect the written region so that
subsequent buffered reads go to disk to read the new data. If this fails
the interface tries to tell the caller that the cache is inconsistent by
returning EIO.
Before this patch we had the problem where this invalidation failure would
clobber -EIOCBQUEUED as it made its way from fs/direct-io.c to fs/aio.c.
Both fs/aio.c and bio completion call aio_complete() and we reference freed
memory, usually oopsing.
This patch addresses this problem by invalidating before the write so that
we can cleanly return -EIO before ->direct_IO() has had a chance to return
-EIOCBQUEUED.
There is a compromise here. During the dio write we can fault in mmap()ed
pages which intersect the written range with get_user_pages() if the user
provided them for the source buffer. This is a crazy thing to do, but we
can make it mostly work in most cases by trying the invalidation again.
The compromise is that we won't return an error if this second invalidation
fails if it's an AIO write and we have -EIOCBQUEUED.
This was tested by having two processes race performing large O_DIRECT and
buffered ordered writes. Within minutes ext3 would see a race between
ext3_releasepage() and jbd holding a reference on ordered data buffers and
would cause invalidation to fail, panicing the box. The test can be found
in the 'aio_dio_bugs' test group in test.kernel.org/autotest. After this
patch the test passes.
Signed-off-by: Zach Brown <zach.brown@oracle.com> Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Cc: Chuck Ebbert <cebbert@redhat.com> Cc: Leonid Ananiev <leonid.i.ananiev@linux.intel.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ankita Garg [Sun, 18 Mar 2007 22:54:14 +0000 (18:54 -0400)]
oom fix: prevent oom from killing a process with children/sibling unkillable
Looking at oom_kill.c, found that the intention to not kill the selected
process if any of its children/siblings has OOM_DISABLE set, is not being
met.
Signed-off-by: Ankita Garg <ankita@in.ibm.com> Cc: Chuck Ebbert <cebbert@redhat.com> Acked-by: Nick Piggin <npiggin@suse.de> Acked-by: William Irwin <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Takashi Iwai [Sun, 18 Mar 2007 22:19:29 +0000 (18:19 -0400)]
hda-intel - Fix codec probe with ATI controllers
[ALSA] hda-intel - Fix codec probe with ATI contorllers
ATI controllers may have up to 4 codecs while ICH up to 3.
Thus the earlier fix to change AZX_MAX_CODECS to 3 cause a regression
on some devices that have the audio codec at bit#3.
Now max codecs is defined according to the driver type, either 3 or 4.
Currently 4 is set only to ATI chips. Other might need the same
change, too.
Dmitry Torokhov [Sun, 18 Mar 2007 21:41:28 +0000 (17:41 -0400)]
Input: i8042 - really suppress ACK/NAK during panic blink
Input: i8042 - really suppress ACK/NAK during panic blink
On some boxes panic blink procedure manages to send both bytes
to keyboard contoller before getting first ACK so we need to
make i8042_suppress_kbd_ack a counter instead of boolean.
Samuel Ortiz [Sat, 17 Mar 2007 02:04:27 +0000 (04:04 +0200)]
IrDA: irttp_dup spin_lock initialisation
Without this initialization one gets
kernel BUG at kernel/rtmutex_common.h:80!
This patch should also be included in the -stable kernel.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Miller [Sat, 17 Mar 2007 01:51:00 +0000 (18:51 -0700)]
Fix page allocation debugging on sparc64
[SPARC64]: Get DEBUG_PAGEALLOC working again.
We have to make sure to use base-pagesize TLB entries even during the
early transition period where we need TLB miss handling but don't have
the kernel page tables setup yet for the linear region.
Also, it is necessary therefore to not use the 4MB TSB for these
translations, and instead use the normal kernel TSB. This allows us
to also get rid of the 4MB tsb for debug builds which shrinks the
kernel a little bit.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexey Dobriyan [Sat, 17 Mar 2007 01:32:09 +0000 (18:32 -0700)]
Copy over mac_len when cloning an skb
[NET]: Copy mac_len in skb_clone() as well
ANK says: "It is rarely used, that's wy it was not noticed.
But in the places, where it is used, it should be disaster."
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ipv6_fl_socklist from listening socket is inadvertently shared
with new socket created for connection. This leads to a variety of
interesting, but fatal, bugs. For example, removing one of the
sockets may lead to the other socket's encountering a page fault
when the now freed list is referenced.
The fix is to not share the flow label list with the new socket.
Signed-off-by: Masayuki Nakagawa <nakagawa.msy@ncos.nec.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Robert Olsson [Sat, 17 Mar 2007 01:30:13 +0000 (18:30 -0700)]
Fix GFP_KERNEL with preemption disabled in fib_trie
[IPV4]: Do not disable preemption in trie_leaf_remove().
Hello, Just discussed this Patrick...
We have two users of trie_leaf_remove, fn_trie_flush and fn_trie_delete
both are holding RTNL. So there shouldn't be need for this preempt stuff.
This is assumed to a leftover from an older RCU-take.
> Mhh .. I think I just remembered something - me incorrectly suggesting
> to add it there while we were talking about this at OLS :) IIRC the
> idea was to make sure tnode_free (which at that time didn't use
> call_rcu) wouldn't free memory while still in use in a rcu read-side
> critical section. It should have been synchronize_rcu of course,
> but with tnode_free using call_rcu it seems to be completely
> unnecessary. So I guess we can simply remove it.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Joy Latten [Sat, 17 Mar 2007 01:27:51 +0000 (18:27 -0700)]
Fix extraneous IPSEC larval SA creation
[XFRM]: Fix missing protocol comparison of larval SAs.
I noticed that in xfrm_state_add we look for the larval SA in a few
places without checking for protocol match. So when using both
AH and ESP, whichever one gets added first, deletes the larval SA.
It seems AH always gets added first and ESP is always the larval
SA's protocol since the xfrm->tmpl has it first. Thus causing the
additional km_query()
Adding the check eliminates accidental double SA creation.
Signed-off-by: Joy Latten <latten@austin.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gautham R Shenoy <ego@in.ibm.com> Acked-by: Neil Brown <neilb@cse.unsw.edu.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Gleixner [Fri, 16 Mar 2007 21:38:20 +0000 (13:38 -0800)]
hrtimer: prevent overrun DoS in hrtimer_forward()
hrtimer_forward() does not check for the possible overflow of
timer->expires. This can happen on 64 bit machines with large interval
values and results currently in an endless loop in the softirq because the
expiry value becomes negative and therefor the timer is expired all the
time.
Check for this condition and set the expiry value to the max. expiry time
in the future. The fix should be applied to stable kernel series as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trond Myklebust [Fri, 16 Mar 2007 21:38:28 +0000 (13:38 -0800)]
nfs: nfs_getattr() can't call nfs_sync_mapping_range() for non-regular files
Looks like we need a check in nfs_getattr() for a regular file. It makes
no sense to call nfs_sync_mapping_range() on anything else. I think that
should fix your problem: it will stop the NFS client from interfering
with dirty pages on that inode's mapping.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 16 Mar 2007 13:34:29 +0000 (09:34 -0400)]
EHCI: add delay to bus_resume before accessing ports
This patch (as870) adds a delay to ehci-hcd's bus_resume routine.
Apparently there are controllers and/or BIOSes out there which need
such a delay to get the ports back into their correct state. This
fixes Bugzilla #8190.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jan Beulich [Tue, 13 Mar 2007 18:04:11 +0000 (14:04 -0400)]
adjust legacy IDE resource setting (v2)
adjust legacy IDE resource setting (v2)
The change to force legacy mode IDE channels' resources to fixed non-zero
values confuses (at least some versions of) X, because the values reported
by the kernel and those readable from PCI config space aren't consistent
anymore. Therefore, this patch arranges for the respective BARs to also
get updated if possible.
Signed-off-by: Jan Beulich <jbeulich@novell.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Cc: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IA64: fix NULL pointer in ia64/irq_chip-mask/unmask function
[IA64] fix NULL pointer in ia64/irq_chip-mask/unmask function
This patch fixes boot failure because irq_desc->mask() is NULL.
- Added mask/unmask functions to ia64's irq desc function table.
- rename hw_interrupt_type to irq_chip. hw_interrupt_type is old name.
- Tony: Added same change to arch/ia64/sn/kernel/irq.c as pointed out
by Eric Biederman ... mask/unmask functions there can be no-op.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com> Cc: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Paul Moore [Mon, 12 Mar 2007 14:33:12 +0000 (09:33 -0500)]
NetLabel: Verify sensitivity level has a valid CIPSO mapping
The current CIPSO engine has a problem where it does not verify that the given
sensitivity level has a valid CIPSO mapping when the "std" CIPSO DOI type is
used. The end result is that bad packets are sent on the wire which should
have never been sent in the first place. This patch corrects this problem by
verifying the sensitivity level mapping similar to what is done with the
category mapping. This patch also changes the returned error code in this case
to -EPERM to better match what the category mapping verification code returns.
Signed-off-by: Paul Moore <paul.moore@hp.com> Acked-by: James Morris <jmorris@namei.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Joerg Dorchain [Tue, 6 Mar 2007 10:46:54 +0000 (02:46 -0800)]
gdth: fix oops in gdth_copy_cmd()
Recent alterations to the gdth_fill_raw_cmd() path no longer set the
sg_ranz field for zero transfer commands. However, this field is used
lower down in the function to initialise ha->cmd_len to the size of
the firmware packet. If this uninitialised field contains a bogus
value, ha->cmd_len can become much larger than the actual firmware
packet and end up oopsing in gdth_copy_cmd() as it tries to copy this
huge packet to the device (usually because it runs into an unallocated
page).
The fix is to initialise the sg_ranz field to zero at the start of
gdth_fill_raw_cmd().
Signed-off-by: Joerg Dorchain <joerg@dorchain.net> Acked-by: "Achim Leubner" <Achim_Leubner@adaptec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Sat, 10 Mar 2007 07:04:42 +0000 (23:04 -0800)]
Fix rtm_to_ifaddr() error return.
[IPV4]: Fix rtm_to_ifaddr() error handling.
Return negative error value (embedded in the pointer) instead of
returning NULL.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Olaf Kirch [Sat, 10 Mar 2007 07:03:53 +0000 (23:03 -0800)]
Fix another NULL pointer deref in ipv6_sockglue.c
[IPV6]: Fix for ipv6_setsockopt NULL dereference
I came across this bug in http://bugzilla.kernel.org/show_bug.cgi?id=8155
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Herbert Xu [Thu, 8 Mar 2007 02:50:54 +0000 (18:50 -0800)]
Fix UDP header pointer after pskb_trim_rcsum()
[UDP]: Reread uh pointer after pskb_trim
The header may have moved when trimming.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eric Dumazet [Thu, 8 Mar 2007 02:48:44 +0000 (18:48 -0800)]
Fix timewait jiffies
[INET]: twcal_jiffie should be unsigned long, not int
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Philipp Reisner [Thu, 8 Mar 2007 02:45:12 +0000 (18:45 -0800)]
Fix callback bug in connector
[CONNECTOR]: Bugfix for cn_call_callback()
When system under heavy stress and must allocate new work
instead of reusing old one, new work must use correct
completion callback.
Patch is based on Philipp's and Lars' work.
I only cleaned small stuff (and removed spaces instead of tabs).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rainer Weikusat [Wed, 3 Jan 2007 14:36:25 +0000 (15:36 +0100)]
fix for bugzilla #7544 (keyspan USB-to-serial converter)
At least the Keyspan USA-19HS USB-to-serial converter supports
two different configurations, one where the input endpoints
have interrupt transfer type and one where they are bulk endpoints.
The default UHCI configuration uses the interrupt input endpoints.
The keyspan driver, OTOH, assumes that the device has only bulk
endpoints (all URBs are initialized by calling usb_fill_bulk_urb
in keyspan.c/ keyspan_setup_urb). This causes the interval field
of the input URBs to have a value of zero instead of one, which
'accidentally' worked with Linux at least up to 2.6.17.11 but
stopped to with 2.6.18, which changed the UHCI support code handling
URBs for interrupt endpoints. The patch below modifies to driver to
initialize its input URBs either as interrupt or as bulk URBs,
depending on the transfertype contained in the associated endpoint
descriptor (only tested with the default configuration) enabling
the driver to again receive data from the serial converter.
Johannes Berg [Thu, 8 Mar 2007 02:42:52 +0000 (18:42 -0800)]
Fix compat_getsockopt
[NET]: Fix compat_sock_common_getsockopt typo.
This patch fixes a typo in compat_sock_common_getsockopt.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: James Morris <jmorris@namei.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Larry Finger [Wed, 7 Mar 2007 18:05:58 +0000 (13:05 -0500)]
bcm43xx: Fix problem with >1 GB RAM
Some versions of the bcm43xx chips only support 30-bit DMA, which means
that the descriptors and buffers must be in the first 1 GB of RAM. On
the i386 and x86_64 architectures with more than 1 GB RAM, an incorrect
assignment may occur. This patch ensures that the various DMA addresses
are within the capability of the chip. Testing has been limited to x86_64
as no one has an i386 system with more than 1 GB RAM.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Douglas Gilbert [Wed, 7 Mar 2007 19:33:38 +0000 (14:33 -0500)]
Fix bug 7994 sleeping function called from invalid context
- addresses the reported bug (with GFP_KERNEL -> GFP_ATOMIC)
- improves error checking, and
- is a subset of the changes to scsi_debug in lk 2.6.21-rc*
Compiled and lightly tested (in lk 2.6.21-rc2 environment).
Signed-off-by: Douglas Gilbert <dougg@torque.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patrick McHardy [Wed, 7 Mar 2007 21:34:45 +0000 (22:34 +0100)]
nfnetlink_log: fix crash on bridged packet
[NETFILTER]: nfnetlink_log: fix crash on bridged packet
physoutdev is only set on purely bridged packet, when nfnetlink_log is used
in the OUTPUT/FORWARD/POSTROUTING hooks on packets forwarded from or to a
bridge it crashes when trying to dereference skb->nf_bridge->physoutdev.
Reported by Holger Eitzenberger <heitzenberger@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patrick McHardy [Wed, 7 Mar 2007 21:34:42 +0000 (22:34 +0100)]
nf_conntrack: fix incorrect classification of IPv6 fragments as ESTABLISHED
[NETFILTER]: nf_conntrack: fix incorrect classification of IPv6 fragments as ESTABLISHED
The individual fragments of a packet reassembled by conntrack have the
conntrack reference from the reassembled packet attached, but nfctinfo
is not copied. This leaves it initialized to 0, which unfortunately is
the value of IP_CT_ESTABLISHED.
The result is that all IPv6 fragments are tracked as ESTABLISHED,
allowing them to bypass a usual ruleset which accepts ESTABLISHED
packets early.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The nf_conntrack_netlink config option is named CONFIG_NF_CT_NETLINK,
but multiple files use CONFIG_IP_NF_CONNTRACK_NETLINK or
CONFIG_NF_CONNTRACK_NETLINK for ifdefs.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix {nf,ip}_ct_iterate_cleanup unconfirmed list handling:
- unconfirmed entries can not be killed manually, they are removed on
confirmation or final destruction of the conntrack entry, which means
we might iterate forever without making forward progress.
This can happen in combination with the conntrack event cache, which
holds a reference to the conntrack entry, which is only released when
the packet makes it all the way through the stack or a different
packet is handled.
- taking references to an unconfirmed entry and using it outside the
locked section doesn't work, the list entries are not refcounted and
another CPU might already be waiting to destroy the entry
What the code really wants to do is make sure the references of the hash
table to the selected conntrack entries are released, so they will be
destroyed once all references from skbs and the event cache are dropped.
Since unconfirmed entries haven't even entered the hash yet, simply mark
them as dying and skip confirmation based on that.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
x86-64: survive having no irq mapping for a vector
Occasionally the kernel has bugs that result in no irq being found for a
given cpu vector. If we acknowledge the irq the system has a good chance
of continuing even though we dropped an irq message. If we continue to
simply print a message and not acknowledge the irq the system is likely to
become non-responsive shortly there after.
AK: Fixed compilation for UP kernels
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Andi Kleen <ak@suse.de> Cc: "Luigi Genoni" <luigi.genoni@pirelli.com> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Marcel Holtmann [Wed, 7 Mar 2007 18:22:40 +0000 (13:22 -0500)]
Fix buffer overflow in Omnikey CardMan 4040 driver (CVE-2007-0005)
Based on a patch from Don Howard <dhoward@redhat.com>
When calling write() with a buffer larger than 512 bytes, the
driver's write buffer overflows, allowing to overwrite the EIP and
execute arbitrary code with kernel privileges.
In read(), there exists a similar problem, but coming from the device.
A malicous or buggy device sending more than 512 bytes can overflow
of the driver's read buffer, with the same effects as above.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Harald Welte <laforge@gnumonks.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
On 2/28/07, KOVACS Krisztian <hidden@balabit.hu> wrote:
>
> Hi,
>
> While reading TCP minisock code I've found this suspiciously looking
> code fragment:
>
> - 8< -
> struct sock *tcp_create_openreq_child(struct sock *sk, struct request_sock *req, struct sk_buff *skb)
> {
> struct sock *newsk = inet_csk_clone(sk, req, GFP_ATOMIC);
>
> if (newsk != NULL) {
> const struct inet_request_sock *ireq = inet_rsk(req);
> struct tcp_request_sock *treq = tcp_rsk(req);
> struct inet_connection_sock *newicsk = inet_csk(sk);
> struct tcp_sock *newtp;
> - 8< -
>
> The above code initializes newicsk to inet_csk(sk), isn't that supposed
> to be inet_csk(newsk)? As far as I can tell this might leave
> icsk_ack.last_seg_size zero even if we do have received data.
Good catch!
David, please apply the attached patch.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Zhang, Yanmin [Thu, 15 Feb 2007 07:37:03 +0000 (23:37 -0800)]
ATA: convert GSI to irq on ia64
If an ATA drive uses legacy mode, ata driver will choose 14 and 15 as the
fixed irq number. On ia64 platform, such numbers are GSI and should be
converted to irq vector.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tony Luck <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Miller [Mon, 5 Mar 2007 23:53:45 +0000 (15:53 -0800)]
video/aty/mach64_ct.c: fix bogus delay loop
CT based mach64 cards were reported to hang on sparc64 boxes when
compiled with gcc-4.1.x and later.
Looking at this piece of code, it's no surprise. A critical
delay was implemented as an empty for() loop, and gcc 4.0.x
and previous did not optimize it away, so we did get a delay.
But gcc-4.1.x and later can optimize it away, and we get crashes.
Use a real udelay() to fix this. Fix verified on SunBlade100.
Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 7628b0a8c01a02966d2228bdf741ddedb128e8f8 (drivers/net/tulip/dmfe:
support basic carrier detection) breaks networking on my Davicom DM9009.
ethtool always reports there is no link. tcpdump shows incoming packets,
but TX is disabled. Reverting the above patch fixes the problem.
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org> Cc: Jeff Garzik <jeff@garzik.org> Cc: Valerie Henson <val_henson@linux.intel.com> Cc: Thomas Bachler <thomas@archlinux.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andrew Morton [Thu, 1 Mar 2007 04:13:21 +0000 (20:13 -0800)]
throttle_vm_writeout(): don't loop on GFP_NOFS and GFP_NOIO allocations
throttle_vm_writeout() is designed to wait for the dirty levels to subside.
But if the caller holds IO or FS locks, we might be holding up that writeout.
So change it to take a single nap to give other devices a chance to clean some
memory, then return.
Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sam Ravnborg [Thu, 1 Mar 2007 04:12:31 +0000 (20:12 -0800)]
fix section mismatch warning in lockdep
lockdep_init() is marked __init but used in several places
outside __init code. This causes following warnings:
$ scripts/mod/modpost kernel/lockdep.o
WARNING: kernel/built-in.o - Section mismatch: reference to .init.text:lockdep_init from .text.lockdep_init_map after 'lockdep_init_map' (at offset 0x105)
WARNING: kernel/built-in.o - Section mismatch: reference to .init.text:lockdep_init from .text.lockdep_reset_lock after 'lockdep_reset_lock' (at offset 0x35)
WARNING: kernel/built-in.o - Section mismatch: reference to .init.text:lockdep_init from .text.__lock_acquire after '__lock_acquire' (at offset 0xb2)
The warnings are less obviously due to heavy inlining by gcc - this is not
altered.
Fix the section mismatch warnings by removing the __init marking, which
seems obviously wrong.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In file included from arch/s390/kernel/early.c:13:
include/linux/lockdep.h:300: warning:
"struct task_struct" declared inside parameter list
include/linux/lockdep.h:300:
warning: its scope is only this definition or
declaration, which is probably not what you want
Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nick Piggin [Sat, 10 Feb 2007 09:46:22 +0000 (01:46 -0800)]
buffer: memorder fix
unlock_buffer(), like unlock_page(), must not clear the lock without
ensuring that the critical section is closed.
Mingming later sent the same patch, saying:
We are running SDET benchmark and saw double free issue for ext3 extended
attributes block, which complains the same xattr block already being freed (in
ext3_xattr_release_block()). The problem could also been triggered by
multiple threads loop untar/rm a kernel tree.
The race is caused by missing a memory barrier at unlock_buffer() before the
lock bit being cleared, resulting in possible concurrent h_refcounter update.
That causes a reference counter leak, then later leads to the double free that
we have seen.
Inside unlock_buffer(), there is a memory barrier is placed *after* the lock
bit is being cleared, however, there is no memory barrier *before* the bit is
cleared. On some arch the h_refcount update instruction and the clear bit
instruction could be reordered, thus leave the critical section re-entered.
The race is like this: For example, if the h_refcount is initialized as 1,
kernel/time/clocksource.c needs struct task_struct on m68k
kernel/time/clocksource.c needs struct task_struct on m68k.
Because it uses spin_unlock_irq(), which, on m68k, uses hardirq_count(), which
uses preempt_count(), which needs to dereference struct task_struct, we
have to include sched.h. Because it would cause a loop inclusion, we
cannot include sched.h in any other of asm-m68k/system.h,
linux/thread_info.h, linux/hardirq.h, which leaves this ugly include in
a C file as the only simple solution.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Cc: Ingo Molnar <mingo@elte.hu> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ken Chen [Thu, 8 Feb 2007 22:20:27 +0000 (14:20 -0800)]
hugetlb: preserve hugetlb pte dirty state
__unmap_hugepage_range() is buggy that it does not preserve dirty state of
huge_pte when unmapping hugepage range. It causes data corruption in the
event of dop_caches being used by sys admin. For example, an application
creates a hugetlb file, modify pages, then unmap it. While leaving the
hugetlb file alive, comes along sys admin doing a "echo 3 >
/proc/sys/vm/drop_caches".
drop_pagecache_sb() will happily free all pages that aren't marked dirty if
there are no active mapping. Later when application remaps the hugetlb
file back and all data are gone, triggering catastrophic flip over on
application.
Not only that, the internal resv_huge_pages count will also get all messed
up. Fix it up by marking page dirty appropriately.
Signed-off-by: Ken Chen <kenchen@google.com> Cc: "Nish Aravamudan" <nish.aravamudan@gmail.com> Cc: Adam Litke <agl@us.ibm.com> Cc: David Gibson <david@gibson.dropbear.id.au> Acked-by: William Irwin <bill.irwin@oracle.com> Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As macbook/macbook pro's also have to live with a single mouse button the
following patch just enables the Macintosh device drivers menu in Kconfig +
adds the macintosh dir to the obj-* to make macbook* users happy (who use
exactly that since months....
Signed-off-by: Soeren Sonnenburg <kernel@nn7.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Eric Van Hensbergen <ericvh@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a fix of regression, which triggered by ~2.6.16.
Patch with name ufs-directory-and-page-cache-from-blocks-to-pages.patch: in
additional to conversation from block to page cache mechanism added new
checks of directory integrity, one of them that directory entry do not
across directory chunks.
But some kinds of UFS: OpenStep UFS and Apple UFS (looks like these are the
same filesystems) have different directory chunk size, then common
UFSes(BSD and Solaris UFS).
So this patch adds ability to works with variable size of directory chunks,
and set it for ufstype=openstep to right size.
Magnus Damm [Tue, 6 Feb 2007 00:20:09 +0000 (16:20 -0800)]
kexec: Fix CONFIG_SMP=n compilation V2 (ia64)
Kexec support for 2.6.20 on ia64 does not build properly using a config
made up by CONFIG_SMP=n and CONFIG_HOTPLUG_CPU=n:
CC arch/ia64/kernel/machine_kexec.o
arch/ia64/kernel/machine_kexec.c: In function `machine_shutdown':
arch/ia64/kernel/machine_kexec.c:77: warning: implicit declaration of function `cpu_down'
AS arch/ia64/kernel/relocate_kernel.o
CC arch/ia64/kernel/crash.o
arch/ia64/kernel/crash.c: In function `kdump_cpu_freeze':
arch/ia64/kernel/crash.c:139: warning: implicit declaration of function `ia64_jump_to_sal'
arch/ia64/kernel/crash.c:139: error: `sal_boot_rendez_state' undeclared (first use in this function)
arch/ia64/kernel/crash.c:139: error: (Each undeclared identifier is reported only once
arch/ia64/kernel/crash.c:139: error: for each function it appears in.)
arch/ia64/kernel/crash.c: At top level:
arch/ia64/kernel/crash.c:84: warning: 'kdump_wait_cpu_freeze' defined but not used
make[1]: *** [arch/ia64/kernel/crash.o] Error 1
make: *** [arch/ia64/kernel] Error 2
Signed-off-by: Magnus Damm <magnus@valinux.co.jp> Acked-by: Simon Horman <horms@verge.net.au> Acked-by: Jay Lan <jlan@sgi.com> Cc: Tony Luck <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The commit was buggy in multiple ways:
- the conversion to ilog2() was incorrect to begin with
- it tested the wrong #defines, so on all architectures but FRV you'd
never see the bug except for constant arguments.
- the new "get_order()" macro used its arguments multiple times, and
didn't even parenthesize them properly
- despite the comments, it was not true that you could use it for
constant initializers, since not all architectures even use the
generic page.h header file.
All of the problems are individually fixable, but it all boils down to:
better just revert it, and re-do it from scratch.
Cc: David Howells <dhowells@redhat.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Andrew Morton <akpm@osdl.org> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Renninger [Thu, 22 Feb 2007 12:52:40 +0000 (13:52 +0100)]
Backport of psmouse suspend/shutdown cleanups
This patch works back to 2.6.17 (earlier kernels seem to
need up/down operations on mutex/semaphore).
psmouse - properly reset mouse on shutdown/suspend
Some people report that they need psmouse module unloaded
for suspend to ram/disk to work properly. Let's make port
cleanup behave the same way as driver unload.
This fixes "bad state" problem on various HP laptops, such
as nx7400.
projects / karo-tx-linux.git / log