Luca Coelho [Tue, 13 Dec 2016 07:48:57 +0000 (09:48 +0200)]
iwlwifi: remove unnecessary argument to iwl_drv_start()
When iwl_drv_start() is called, trans->cfg must already be set, so
there's no need to pass cfg separately, since it can be accessed
directly from trans->cfg.
Johannes Berg [Thu, 8 Dec 2016 09:38:08 +0000 (10:38 +0100)]
iwlwifi: mvm: align copy-break SKB payload for MQ RX
When a small frame is copied completely into the skb->head, the code
doesn't take alignment into account, making mac80211 copy it again
later on architectures that need the alignment. Avoid this by taking
the PAD flag from the device into account when copying.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the check whether to decrement the pending frames
counter relies on the tid status and not on the txq id.
This may result in an inconsistent state of the pending frames
counter in case frame is queued on a non aggregation queue but
with this TID, and will be followed by a failure to remove the
station and later on SYSASSERT 0x3421 when trying to remove the
MAC.
Such frames are for example bar and qos NDPs.
Fix it by aligning the condition of incrementing the counter
with the condition of decrementing it - rely on TID state for
DQA mode.
Also, avoid internal error like this affecting station removal
for DQA mode - since we can know for sure it is an internal
error.
Fixes: cf961e16620f ("iwlwifi: mvm: support dqa-mode agg on non-shared queue") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Wed, 7 Dec 2016 10:22:11 +0000 (12:22 +0200)]
iwlwifi: pcie: fix the set of DMA memory mask
Our 9000 device supports 64 bit DMA address for RX only, and
not for TX.
Setting DMA mask to 64 for the whole device is erroneous - we
can do it only for a000 devices where device is capable of
both RX & TX DMA with 64 bit address space.
Fixes: 96a6497bc3ed ("iwlwifi: pcie: add 9000 series multi queue rx DMA support") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Liad Kaufman [Thu, 24 Nov 2016 13:31:00 +0000 (15:31 +0200)]
iwlwifi: mvm: release static queues on bcast release
A few of the static queues are enabled along with the bcast
STA. Make sure they are removed along with it, rather than
waiting for the mac ctxt release.
This is needed because we sometimes have a STA being removed
and then added again (either with the same sta_id or a
different one). If we wait for the mac ctxt release we will
try to allocate the queues again (as this is currently done
in the STA allocation and not in the MAC init) although
they weren't freed, and even if the sta_id of the STA has
changed.
Johannes Berg [Fri, 2 Dec 2016 09:04:49 +0000 (10:04 +0100)]
iwlwifi: mvm/pcie: adjust A-MSDU tx_cmd length in PCIe
Instead of setting the tx_cmd length in the mvm code, which is
complicated by the fact that DQA may want to temporarily store
the SKB on the side, adjust the length in the PCIe code which
also knows about this since it's responsible for duplicating
all those headers that are account for in this code.
As the PCIe code already relies on the tx_cmd->len field, this
doesn't really introduce any new dependencies.
To make this possible we need to move the memcpy() of the TX
command until after it was updated.
This does even simplify the code though, since the PCIe code
already does a lot of manipulations to build A-MSDUs correctly
and changing the length becomes a simple operation to see how
much was added/removed, rather than predicting it.
Fixes: 24afba7690e4 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Fri, 2 Dec 2016 08:57:40 +0000 (09:57 +0100)]
iwlwifi: mvm: overwrite skb info later
We don't really need clear the skb's status area nor store the
dev_cmd into it until we really commit to the frame by handing
it to the transport - defer those operations until just before
we do that.
This doesn't entirely fix the bug with frames not getting sent
out after having been deferred due to DQA, because it doesn't
restore the info->driver_data[0] place that was already set to
zero (or another value) by the A-MSDU logic.
Fixes: 24afba7690e4 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Thu, 1 Dec 2016 15:25:30 +0000 (16:25 +0100)]
iwlwifi: mvm: set AID to firmware only for associated stations
The firmware will soon actually look at the AID field, and
when it does that it'll try to ensure that the AID is never
changing. Due to the way the station is added, it may start
with an invalid AID before it's associated, so to ensure a
constant AID (once it becomes non-zero), track the station
state and set the AID only when the station is associated
and when it disassociates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Wed, 30 Nov 2016 16:04:52 +0000 (17:04 +0100)]
iwlwifi: mvm: fix D3 replay counter value
This fixes a long-standing bug that was introduced when this code
was introduced: cfg80211 passes a pointer, but we treat it as if
it was passing a value. The result is that we pass the pointer to
the firmware, instead of the value. It's not clear how this could
ever have worked, unless the firmware is ignoring this value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When driver needs to access the contents of a streaming DMA buffer
without unmapping it it should call dma_sync_single_for_cpu().
Once the call has been made, the CPU "owns" the DMA buffer and can
work with it as needed.
Before the device accesses the buffer, however, ownership should be
transferred back to it with dma_sync_single_for_device().
Both calls weren't performed by the driver, resulting with odd paging
errors on some platforms. Fix it.
Fixes: a6c4fb4441f4 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Wed, 16 Nov 2016 15:04:36 +0000 (17:04 +0200)]
iwlwifi: mvm: always free inactive queue when moving ownership
If iwl_mvm_find_free_queue() doesn't find a free queue, it will
return an inactive one.
However, not all the call paths free this queue before reassigning
it, which is a bug.
Check it in other paths and act accordingly.
Fixes: 9794c64f302d ("iwlwifi: mvm: support dqa queue inactivation upon timeout") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Sun, 20 Nov 2016 11:50:39 +0000 (13:50 +0200)]
iwlwifi: mvm: cleanup incorrect and redundant define
Currently we have up to 3 phy contexts - defined by NUM_PHY_CTX.
However - some code paths validate the ID by using MAX_PHYS define
which is set to 4.
While there is no harm it is incorrect - since the maximum is 3.
Remove the define and use the correct one.
Cleanup the code a bit while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Beni Lev [Thu, 17 Nov 2016 12:03:17 +0000 (14:03 +0200)]
iwlwifi: mvm: Use aux queue for offchannel frames in dqa
Since offchannel activity doesn't always require a BSS, e.g. ANQP
sessions, offchannel frames should not use the BSS queue, because it
might not be initialized.
Use the auxilary queue instead
Fixes: e3118ad74d7e ("iwlwifi: mvm: support tdls in dqa mode") Signed-off-by: Beni Lev <beni.lev@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sara Sharon [Wed, 31 Aug 2016 15:13:57 +0000 (18:13 +0300)]
iwlwifi: mvm: support unification of INIT and RT images
For a000 devices the INIT and RT images are unified to one
image.
The changes in the flow are the following:
* Driver load only RT firmware - meaning that the nvm access
command will be done in the RT image load flow.
* A new command (NVM_ACCESS_COMPLETE) now signals to the FW that
the driver is done accessing the NVM and FW can proceed with phy
calibrations.
* Phy DB is no longer sent from INIT FW to be restored by driver
for the RT FW - all the phy DB is now internal to the FW.
INIT complete will now follow the NVM access command, without
phy DB calls before.
* Paging command is sent earlier in the flow before NVM access
to enable a complete load of FW.
* caution must be care when restart is called since we may have
not completed init flow even though we are in RT firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rafał Miłecki [Mon, 30 Jan 2017 15:09:52 +0000 (16:09 +0100)]
brcmfmac: be more verbose when PSM's watchdog fires
It's important to inform user so he knows things went wrong. He may also
want to get memory dump for further debugging purposes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Mon, 30 Jan 2017 15:09:51 +0000 (16:09 +0100)]
brcmfmac: check brcmf_bus_get_memdump result for error
This method may be unsupported (see: USB bus) or may just fail (see:
SDIO bus).
While at it rework logic in brcmf_sdio_bus_get_memdump function to avoid
too many conditional code nesting levels.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Tue, 31 Jan 2017 21:54:54 +0000 (22:54 +0100)]
net: phy: broadcom: rehook BCM54612E specific init
This extra BCM54612E code in PHY driver isn't really aneg specific. Even
without it aneg works OK but the problem is no packets pass through PHY.
Moreover putting this code inside config_aneg callback didn't allow
resuming PHY correctly. When driver called phy_stop and phy_start it was
putting PHY machine into RESUMING state. After that machine was
switching into AN and NOLINK without ever calling phy_start_aneg. This
prevented this extra setup from being called and PHY didn't work.
This change has been verified to fix network on BCM47186B0 SoC device
with BCM54612E.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The ASSERT_RTNL is not necessary in the init function, as it does not
touch any rtnl protected structures, as opposed to the mirred action which
does have to hold a net device.
Reported-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth: fix wakeup event reporting from MagicPacket
If a link change interrupt happens along side the MagicPacket interrupt
and the link change interrupt is ignored the interrupt handler will
return and the wakeup event is not registered. Fix this by moving the
MagicPacket check before the link change check.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth: align usage of sh_eth_modify() with rest of driver
To be consistent with the rest of the driver when setting bits using
sh_eth_modify() the same bit should also be cleared. This have no
functional change and should have been done from the start.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Feb 2017 17:46:17 +0000 (12:46 -0500)]
Merge tag 'wireless-drivers-next-for-davem-2017-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 1 Feb 2017 08:52:15 +0000 (11:52 +0300)]
ethernet: aquantia: fix dma_mapping_error test
dma_mapping_error() returns 1 if there is an error and 0 if not.
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 1 Feb 2017 00:51:37 +0000 (16:51 -0800)]
net: ipv6: add NLM_F_APPEND in notifications when applicable
IPv6 does not set the NLM_F_APPEND flag in notifications to signal that
a NEWROUTE is an append versus a new route or a replaced one. Add the
flag if the request has it.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In switch mode on struct cpsw_slave->ndev field will be initialized with
proper value only for the one cpsw slave port, as result
cpsw_get_usage_count() will generate "Unable to handle kernel NULL pointer
dereference" exception when first ethernet interface is opening
cpsw_ndo_open(). This issue causes boot regression on AM335x EVM and
reproducible on am57xx-evm (switch mode).
Fix it by adding additional check for !cpsw->slaves[i].ndev in
cpsw_get_usage_count().
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Fixes: 03fd01ad0eea ("net: ethernet: ti: cpsw: don't duplicate ndev_running") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Theuns Verwoerd [Mon, 30 Jan 2017 23:23:46 +0000 (12:23 +1300)]
rtnetlink: Handle IFLA_MASTER parameter when processing rtnl_newlink
Allow a master interface to be specified as one of the parameters when
creating a new interface via rtnl_newlink. Previously this would
require invoking interface creation, waiting for it to complete, and
then separately binding that new interface to a master.
In particular, this is used when creating a macvlan child interface for
VRRP in a VRF configuration, allowing the interface creator to specify
directly what master interface should be inherited by the child,
without having to deal with asynchronous complications and potential
race conditions.
Signed-off-by: Theuns Verwoerd <theuns.verwoerd@alliedtelesis.co.nz> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2) Don't acquire state lock in get_mtu functions.
The only rece against a dead state does not matter.
From Florian Westphal.
3) Remove xfrm4_state_fini, it is unused for more than
10 years. From Florian Westphal.
4) Various rcu usage improvements. From Florian Westphal.
5) Properly handle crypto arrors in ah4/ah6.
From Gilad Ben-Yossef.
6) Try to avoid skb linearization in esp4 and esp6.
7) The esp trailer is now set up in different places,
add a helper for this.
8) With the upcomming usage of gro_cells in IPsec,
a gro merged skb can have a secpath. Drop it
before freeing or reusing the skb.
9) Add a xfrm dummy network device for napi. With
this we can use gro_cells from within xfrm,
it allows IPsec GRO without impact on the generic
networking code.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 31 Jan 2017 18:44:50 +0000 (13:44 -0500)]
Merge branch 'bgmac-phy-init'
Rafał Miłecki says:
====================
net-next: use one struct bgmac & add PHY support
This patchset adds support for initializing PHY using PHY subsystem.
It's required e.g. for wireless access point devices that use bgmac
supported Ethernet device connected to some external PHY.
Implementing this required accessing phydev in bcma specific code which
wasn't possible with core code allocating struct bgmac on its own. This
is why I needed to modify alloc_etherdev usage first.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafał Miłecki [Tue, 31 Jan 2017 18:37:56 +0000 (19:37 +0100)]
net: bgmac: use PHY subsystem for initializing PHY
This adds support for using bgmac with PHYs supported by standalone PHY
drivers. Having any PHY initialization in bgmac is hacky and shouldn't
be extended but rather removed if anyone has hardware to test it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rafał Miłecki [Tue, 31 Jan 2017 18:37:55 +0000 (19:37 +0100)]
net: bgmac: drop struct bcma_mdio we don't need anymore
Adding struct bcma_mdio was a workaround for bcma code not having access
to the struct bgmac used in the core code. Now we don't duplicate this
struct we can just use it internally in bcma code.
This simplifies code & allows access to all bgmac driver details from
all places in bcma code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rafał Miłecki [Tue, 31 Jan 2017 18:37:54 +0000 (19:37 +0100)]
net: bgmac: allocate struct bgmac just once & don't copy it
So far were were allocating struct bgmac in 3 places: platform code,
bcma code and shared bgmac_enet_probe function. The reason for this was
bgmac_enet_probe:
1) Requiring early-filled struct bgmac
2) Calling alloc_etherdev on its own in order to use netdev_priv later
This solution got few drawbacks:
1) Was duplicating allocating code
2) Required copying early-filled struct
3) Resulted in platform/bcma code having access only to unused struct
Solve this situation by simply extracting some probe code into the new
bgmac_alloc function.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 31 Jan 2017 03:17:16 +0000 (19:17 -0800)]
net: dsa: bcm_sf2: Fix build module
Commit 7318166cacad ("net: dsa: bcm_sf2: Add support for
ethtool::rxnfc") added a new object to build: bcm_sf2_cfp.o, but in
doing so, we essentially just built this object and no longer bcm_sf2.o.
Fix this by creating a module named bcm-sf2.ko which links in bcm_sf2.o
and bcm_sf2_cfp.o.
Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
~1160 mlx5 counters ~= order 4 allocation which is unlikely to succeed
under memory pressure. Convert them to vzalloc() as ethtool_get_regs() does.
Also take care of drivers without counters similar to
commit 67ae7cf1eeda ("ethtool: Allow zero-length register dumps again")
and reduce warn_on to warn_on_once.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Mon, 30 Jan 2017 22:04:42 +0000 (23:04 +0100)]
net: aquantia: atlantic: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Tested-by: Pavel Belous <pavel.s.belous@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 31 Jan 2017 16:30:02 +0000 (16:30 +0000)]
sfc: fix an off-by-one compare on an array size
encap_type should be checked to see if it is greater or equal to
the size of array map to fix an off-by-one array size check. This
fixes an array overrun read as detected by static analysis by
CoverityScan, CID#1398883 ("Out-of-bounds-read")
Fixes: 9b41080125176841e ("sfc: insert catch-all filters for encapsulated traffic") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rafał Miłecki [Sat, 28 Jan 2017 22:11:34 +0000 (23:11 +0100)]
bcma: make OF code more generic (not platform_device specific)
OF allows not only specifying platform devices but also describing
devices on standard buses like PCI or USB. This change will allow
reading info from DT for bcma buses hosted on PCI cards.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend Van Spriel [Fri, 27 Jan 2017 12:27:47 +0000 (12:27 +0000)]
brcmfmac: allow wowlan support to be per device
The wowlan support is (partially) determined dynamic by checking the
device/firmware capabilities. So they can differ per device. So it
is not possible to use a static global. Instead use the global as a
template and use kmemdup(). When kmemdup() fails the template is used
unmodified.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend Van Spriel [Fri, 27 Jan 2017 12:27:46 +0000 (12:27 +0000)]
brcmfmac: fix handling firmware results for wowl netdetect
For wowl netdetect the event data changed for newer chips. This
was recently fixed for scheduled scan, but same change is needed
for wowl netdetect. Removing now pointles += operation from both
result handlers.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend Van Spriel [Fri, 27 Jan 2017 12:27:45 +0000 (12:27 +0000)]
brcmfmac: provide a value for struct wowlan_support::max_nd_match_sets
The driver advertises support for WOWLAN_NETDETECT but did not specify
maximum amount of netdetect match sets. This was no issue due to a bug
in nl80211. As that has been fixed, brcmfmac also needs fixing.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by: Franky Lin <franky.lin@broadcom.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sara Sharon [Mon, 30 Jan 2017 10:34:32 +0000 (12:34 +0200)]
iwlwifi: alloc memory dynamically also for DVM
For old firmwares the memory wasn't allocated, resulting in panic.
Make it dynamically allocated as well. Allow any order of functions
call.
Fixes: eef187a7b8a1 ("iwlwifi: enlarge number of ucode sections") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Tested-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clk_get() takes two arguments and might return ERR_PTR(), so we
have to nullify pointer on that case, to do not break further call
to clk_get_rate().
Reported-by: Felix Fietkau <nbd@nbd.name> Fixes: 34db70b92fae ("rt2x00: add copy of clk for soc devices") Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Here's a set of 3 patches against DaveM's 'net-next.git' repo. The main goal
of this set is to stop using the bare numbers for the E-DMAC interrupt masks.
[1/3] sh_eth: rename EESIPR bits
[2/3] sh_eth: add missing EESIPR bits
[3/3] sh_eth: stop using bare numbers for EESIPR values
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 29 Jan 2017 12:13:48 +0000 (15:13 +0300)]
sh_eth: stop using bare numbers for EESIPR values
Now that we have almost all EESIPR bits declared (and those that are
still not are most probably reserved anyway) we can at last replace the
bare numbers used for 'sh_eth_cpu_data::eesipr_value' initializers with
the bit names ORed together...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 29 Jan 2017 12:08:09 +0000 (15:08 +0300)]
sh_eth: add missing EESIPR bits
Renesas SH77{34|63} manuals describe more EESIPR bits than the current
driver. Declare the new bits with the end goal of using the bit names
instead of the bare numbers for the 'sh_eth_cpu_data::eesipr_value'
initializers...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 29 Jan 2017 12:07:34 +0000 (15:07 +0300)]
sh_eth: rename EESIPR bits
Since the commit b0ca2a21f769 ("sh_eth: Add support of SH7763 to sh_eth")
the *enum* declaring the EESIPR bits (interrupt mask) went out of sync with
the *enum* declaring the EESR bits (interrupt status) WRT bit naming and
formatting. I'd like to restore the consistency by using EESIPR as the bit
name prefix, renaming the *enum* to EESIPR_BIT, and (finally) renaming the
bits according to the available Renesas SH77{34|63} manuals; additionally,
reconstruct couple names using the EESR bit declaration above...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Jan 2017 21:50:57 +0000 (16:50 -0500)]
Merge branch 'ESPRESSObin-ethernet'
Gregory CLEMENT says:
====================
dsa: Add support for the ethernet switch on the ESPRESSObin
This set of patches adds support for the Marvell Ethernet Topaz switch
family (88E6141/88E6341) which is found on the ESPRESSObin. With this
series the network is usable on this board.
As usual, I rebased the series on the very last net-next/master. In
this series there is no temperature support which need some patches
form Andrew Lunn.
As soon as Andrew Lunn will post the needed patch I will send a patch
to enable the temperature support.
Changelog:
v6 -> v7:
- rebased on net-next/master (5b8784aaf29b)
- Fixed the wrong age time coeff from 15s to 3.75s.
- Remove support for temperature sensor
v5 -> v6:
- rebased on net-next/master (d140199af510)
- Fix the redundant check on mv88e6xxx_6341_family (reported by Julia
Lawall)
- Add support for the 88E6141
- Move support for temperature sensor in the phy part
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT [Mon, 30 Jan 2017 19:29:35 +0000 (20:29 +0100)]
net: dsa: mv88e6xxx: Add support for ethernet switch 88E6141
The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces.
It belongs to the Topaz family and unlike the 88E6341 it does not have
a TCAM.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT [Mon, 30 Jan 2017 19:29:34 +0000 (20:29 +0100)]
net: dsa: mv88e6xxx: Add support for ethernet switch 88E6341
The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces. It is partially compatible with switches of family 88E6352 and switches of family 88E6390.
This commit adds an initial support for this switch by describing its
capabilities to the driver and introducing a new family.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell ethernet switches have internal ethernet transceivers with
hardcoded phy addresses. These addresses can be greater than the number
of ports or its value might be different than the associated port number.
This is for example the case for MV88E6341 that has 6 ports and internal
Port 1 to Port4 PHYs mapped at SMI addresses from 0x11 to 0x14.
This commits fixes the issue by removing the condition in MDIO callbacks.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Mon, 30 Jan 2017 09:55:04 +0000 (10:55 +0100)]
smc: some potential use after free bugs
Say we got really unlucky and these failed on the last iteration, then
it could lead to a use after free bug.
Fixes: cd6851f30386 ("smc: remote memory buffers (RMBs)") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Jan 2017 20:55:48 +0000 (15:55 -0500)]
Merge branch 'dsa-port-mirroring'
Florian Fainelli says:
====================
net: dsa: Port mirroring support
This patch series adds support for port mirroring in the two
Broadcom switch drivers. The major part of the functional are actually with
the plumbing between tc and the drivers.
Changes in v5:
- Added Jiri's Reviewed-by tag to first patch
- rebase against latest net-next/master after bcm_sf2 CFP series
Changes in v4:
- rebased against latest net-next/master after Vivien's changes
Changes in v3:
- removed multiline comments from added structures
- simplify error handling in dsa_slave_add_cls_matchall
Changes in v2:
- fixed filter removal logic to disable the ingress or egress mirroring
when there are no longer ports being monitored in ingress or egress
- removed a stray list_head in dsa_port structure that is not used
Tested using the two iproute2 examples:
tc qdisc add dev eth1 handle ffff: ingress
tc filter add dev eth1 parent ffff: \
matchall skip_sw \
action mirred egress mirror \
dev eth2
tc qdisc add dev eth1 handle 1: root prio
tc filter add dev eth1 parent 1: \
matchall skip_sw \
action mirred egress mirror \
dev eth2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 30 Jan 2017 20:41:42 +0000 (12:41 -0800)]
net: dsa: b53: Add support for port mirroring
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress or egress capture towards the capture
port. Future improvements could include leveraging the divider to allow
less frames to be captured, as well as matching specific MAC DA/SA.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 30 Jan 2017 20:41:40 +0000 (12:41 -0800)]
net: dsa: Add plumbing for port mirroring
Add necessary plumbing at the slave network device level to have switch
drivers implement ndo_setup_tc() and most particularly the cls_matchall
classifier. We add support for two switch operations:
port_add_mirror and port_del_mirror() which configure, on a per-port
basis the mirror parameters requested from the cls_matchall classifier.
Code is largely borrowed from the Mellanox Spectrum switch driver.
Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Jan 2017 20:26:44 +0000 (15:26 -0500)]
Merge branch 'mlx4-misc-improvements'
Tariq Toukan says:
====================
mlx4 misc improvements
This patchset contains several improvements and cleanups
from the team to the mlx4 Eth and core drivers.
Series generated against net-next commit: 4e8f2fc1a55d Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Thanks,
Tariq.
v3:
* Patch 6/9: forgot to actually update the commit message in v2, now it is.
v2:
* Patch 1/9: used EOPNOTSUPP and not ENOTSUPP.
* Patch 3/9: dropped, to be submitted separately in the future.
* Patch 6/9: updated commit message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shaker Daibes [Sun, 29 Jan 2017 16:56:20 +0000 (18:56 +0200)]
net/mlx4_en: Check the enabling pptx/pprx flags in SET_PORT wrapper flow
Make sure pptx/pprx mask flag is set using new fields upon set port
request. In addition, move this code into a helper function for better
code readability.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shaker Daibes [Sun, 29 Jan 2017 16:56:19 +0000 (18:56 +0200)]
net/mlx4_en: Check the enabling mtu flag in SET_PORT wrapper flow
Make sure MTU mask flag is set using new field upon set port
request. In addition, move this code into a helper function for better
code readability.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shaker Daibes [Sun, 29 Jan 2017 16:56:18 +0000 (18:56 +0200)]
net/mlx4_en: Pass user MTU value to Firmware at set port command
When starting the port, driver will inform Firmware about the actual MTU
which does not include implicit headers, such as FCS or VLAN tags.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Levkovich [Sun, 29 Jan 2017 16:56:17 +0000 (18:56 +0200)]
net/mlx4_en: Adding support of turning off link autonegotiation via ethtool
This feature will allow the user to disable auto negotiation
on the port for mlx4 devices while setting the speed is limited
to 1GbE speeds.
Other speeds will not be accepted in autoneg off mode.
This functionality is permitted providing that the firmware
is compatible with this feature.
The above is determined by querying a new dedicated capability
bit in the device.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alaa Hleihel [Sun, 29 Jan 2017 16:56:16 +0000 (18:56 +0200)]
net/mlx4_core: Get num_tc using netdev_get_num_tc
Avoid reading num_tc directly from struct net_device, but use
the helper function netdev_get_num_tc.
Fixes: bc6a4744b827 ("net/mlx4_en: num cores tx rings for every UP") Fixes: f5b6345ba8da ("net/mlx4_en: User prio mapping gets corrupted when changing number of channels") Signed-off-by: Alaa Hleihel <alaa@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In order to aid debugging of functions that take a resource but
don't put it, add the last function name that successfully grabbed
this resource.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yishai Hadas [Sun, 29 Jan 2017 16:56:14 +0000 (18:56 +0200)]
net/mlx4_core: Device revision support
The device revision field returned by the NodeInfo MAD is incorrect
on ConnectX3 devices.
This patch is driver side handling to complete a FW fix added at 2.11.1172.
INIT_HCA - bit at offset 0x0C.12 is set to 1 so that FW will report
correct device revision.
Older FW versions won't be affected from turning on that bit,
no capability bit is needed.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 30 Jan 2017 16:22:01 +0000 (08:22 -0800)]
drivers: net: generalize napi_complete_done()
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396ba
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Thu, 26 Jan 2017 18:02:24 +0000 (18:02 +0000)]
net: Avoid receiving packets with an l3mdev on unbound UDP sockets
Packets arriving in a VRF currently are delivered to UDP sockets that
aren't bound to any interface. TCP defaults to not delivering packets
arriving in a VRF to unbound sockets. IP route lookup and socket
transmit both assume that unbound means using the default table and
UDP applications that haven't been changed to be aware of VRFs may not
function correctly in this case since they may not be able to handle
overlapping IP address ranges, or be able to send packets back to the
original sender if required.
So add a sysctl, udp_l3mdev_accept, to control this behaviour with it
being analgous to the existing tcp_l3mdev_accept, namely to allow a
process to have a VRF-global listen socket. Have this default to off
as this is the behaviour that users will expect, given that there is
no explicit mechanism to set unmodified VRF-unaware application into a
default VRF.
Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Tested-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Jan 2017 19:49:59 +0000 (14:49 -0500)]
Merge branch 'net-dsa-bcm_sf2-CFP-support'
Florian Fainelli says:
====================
net: dsa: bcm_sf2: CFP support
This patch series adds support for the Broadcom Compact Field Processor (CFP)
which is a classification and matching engine built into most Broadcom switches.
We support that using ethtool::rxnfc because it allows all known uses cases from
the users I support to work, and more importantly, it allows the selection of a
target rule index, which is later used by e.g: offloading hardware, this is an
essential feature that I could not find being supported with cls_* for instance.
Thanks!
Changes in v3:
- rebased against latest net-next/master after Vivien's changes
Changes in v2:
- fixed modular builds reported by kbuild test robot
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 30 Jan 2017 17:48:43 +0000 (09:48 -0800)]
net: dsa: bcm_sf2: Add support for ethtool::rxnfc
Add support for configuring classification rules using the
ethtool::rxnfc API. This is useful to program the switch's CFP/TCAM to
redirect specific packets to specific ports/queues for instance. For
now, we allow any kind of IPv4 5-tuple matching.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 30 Jan 2017 17:48:41 +0000 (09:48 -0800)]
net: dsa: bcm_sf2: Configure traffic classes to queue mapping
By default, all traffic goes to queue 0, re-configure the traffic
classes to quality of service mapping such that priority X maps to queue
X, where X is from 0 through 7.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert [Mon, 30 Jan 2017 05:45:43 +0000 (06:45 +0100)]
xfrm: Add a dummy network device for napi.
This patch adds a dummy network device so that we can
use gro_cells for IPsec GRO. With this, we handle IPsec
GRO with no impact on the generic networking code.
Rafał Miłecki [Sat, 28 Jan 2017 14:15:42 +0000 (15:15 +0100)]
net: add devm version of alloc_etherdev_mqs function
This patch adds devm_alloc_etherdev_mqs function and devm_alloc_etherdev
macro. These can be used for simpler netdev allocation without having to
care about calling free_netdev.
Thanks to this change drivers, their error paths and removal paths may
get simpler by a bit.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Sat, 28 Jan 2017 00:24:39 +0000 (16:24 -0800)]
tcp: include locally failed retries in retransmission stats
Currently the retransmission stats are not incremented if the
retransmit fails locally. But we always increment the other packet
counters that track total packet/bytes sent. Awkwardly while we
don't count these failed retransmits in RETRANSSEGS, we do count
them in FAILEDRETRANS.
If the qdisc is dropping many packets this could under-estimate
TCP retransmission rate substantially from both SNMP or per-socket
TCP_INFO stats. This patch changes this by always incrementing
retransmission stats on retransmission attempts and failures.
Another motivation is to properly track retransmists in
SCM_TIMESTAMPING_OPT_STATS. Since SCM_TSTAMP_SCHED collection is
triggered in tcp_transmit_skb(), If tp->total_retrans is incremented
after the function, we'll always mis-count by the amount of the
latest retransmission.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Sat, 28 Jan 2017 00:24:38 +0000 (16:24 -0800)]
tcp: record pkts sent and retransmistted
Add two stats in SCM_TIMESTAMPING_OPT_STATS:
TCP_NLA_DATA_SEGS_OUT: total data packets sent including retransmission
TCP_NLA_TOTAL_RETRANS: total data packets retransmitted
The names are picked to be consistent with corresponding fields in
TCP_INFO. This allows applications that are using the timestamping
API to measure latency stats to also retrive retransmission rate
of application write.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Fri, 27 Jan 2017 22:43:48 +0000 (16:43 -0600)]
net: qcom/emac: add an error interrupt handler for the sgmii
The SGMII (internal PHY) can report decode errors via an interrupt. It
can also report autonegotiation status changes, but we don't need to track
those. The SGMII can recover automatically from most decode errors, so
we only reset the interface if we get multiple consecutive errors.
It's possible for bogus decode errors to be reported while the link is
being brought up. The interrupt is registered when the interface is
opened, and it's enabled after the link is up.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC driver does not support wake-on-lan, but there is still
code left-over that partially enables it. Remove that code and a few
macros that support it.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Fri, 27 Jan 2017 22:43:44 +0000 (16:43 -0600)]
net: qcom/emac: always use autonegotiation to configure the SGMII link
Regardless of how the external PHY is configured, the internal PHY
(the "SGMII" block) is capable of configuring the SGMII link automatically.
When the external PHY link comes up, regardless of how it is configured,
the SGMII link is configured automatically.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Fri, 27 Jan 2017 22:43:43 +0000 (16:43 -0600)]
net: qcom/emac: display the phy driver info after we connect
The PHY driver is attached only when the driver calls
phy_connect_direct(). Calling phy_attached_print() to display
information about the PHY driver prior to that point is meaningless.
The interface can be brought down, a new PHY driver can be loaded,
and the interface then brought back up. This is the correct time
to display information about the attached driver.
Since phy_attached_print() also prints information about the
interrupt, that needs to be set as well.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log