Frank Schaefer [Sat, 15 Apr 2017 10:05:03 +0000 (07:05 -0300)]
[media] em28xx: shed some light on video input formats
CbYCrY has been identified by looking into the tvp5150 driver and the
saa7115 datasheet.
YUV formats have been verified with em2765 + ov2640 (VAD Laplace webcam).
RGB8 formats have been verified with em2710/em2820 + mt9v011 (Silvercrest
webcam 1.3mpix).
I also did some cross-checking with these two camera devices and 0x08-0x0b
are at least 16 bits per pixel formats on em2710/em2820, too, and
0x0c-0x0f are at least 8 bits per pixel formats on em2765, too.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Frank Schaefer [Sat, 15 Apr 2017 10:05:02 +0000 (07:05 -0300)]
[media] em28xx: don't treat device as webcam if an unknown sensor is detected
With an unknown sensor, norm_maxw() and norm_maxh() return 0 as max.
height and width values, which causes a devide by zero in size_to_scale().
Of course we could use speculative default values for unknown sensors,
but the chance that the device works at this resolution without any
driver/setup is very low and therefore not worth the efforts.
Instead, just don't treat the device as camera.
A message will then be printed to the log that the device isn't supported.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Frank Schaefer [Sat, 15 Apr 2017 10:05:01 +0000 (07:05 -0300)]
[media] em28xx: add missing auto-selections for build
With MEDIA_SUBDRV_AUTOSELECT enabled in the kernel config, the em28xx
driver currently does't select some used subdrivers.
Fix this by adding the missing auto-selections to the Kconfig file.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Frank Schaefer [Sat, 15 Apr 2017 10:05:00 +0000 (07:05 -0300)]
[media] em28xx: get rid of the dummy clock source
The v4l2 dummy clock has been added with commit fc5d0f8a8878
("V4L2: em28xx: register a V4L2 clock source") to be able to use the ov2640
soc_camera driver.
Since commit 46796cfcd346 ("ov2640: use standard clk and enable it") it is
no longer required.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Frank Schaefer [Sun, 16 Apr 2017 17:41:52 +0000 (14:41 -0300)]
[media] em28xx: simplify ID-reading from Micron sensors
Use i2c_smbus_read_word_data() instead of i2c_master_send() and
i2c_master_recv() for reading the ID of Micorn sensors.
i2c_smbus_read_word_data() assumes that byes are in little-endian,
so, it uses:
data->word = msgbuf1[0] | (msgbuf1[1] << 8);
However, Micron datasheet describes the ID as if they were read
in big-endian. So, we need to change the byte order in order to
match the ID number as described on their datasheets.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Jasmin J [Sat, 18 Mar 2017 02:04:20 +0000 (23:04 -0300)]
[media] media/dvb-core: Race condition when writing to CAM
It started with a sporadic message in syslog: "CAM tried to send a
buffer larger than the ecount size" This message is not the fault
itself, but a consecutive fault, after a read error from the CAM. This
happens only on several CAMs, several hardware, and of course sporadic.
It is a consecutive fault, if the last read from the CAM did fail. I
guess this will not happen on all CAMs, but at least it did on mine.
There was a write error to the CAM and during the re-initialization
procedure, the CAM finished the last read, although it got a RS.
The write error to the CAM happened because a race condition between HC
write, checking DA and FR.
This patch added an additional check for DA(RE), just after checking FR.
It is important to read the CAMs status register again, to give the CAM
the necessary time for a proper reaction to HC. Please note the
description within the source code (patch below).
Daniel Scheller [Tue, 14 Mar 2017 22:22:37 +0000 (19:22 -0300)]
[media] dvb-frontends/drxk: don't log errors on unsupported operation mode
When fe_ops.read_status is called and no channel is tuned (yet), the
subsequent calls to get_lock_status() causes the kernel log to be filled
with
drxk: Error -22 on get_lock_status
which either means a NULL pointer was passed for the p_lock_status var,
or neither QAM nor OFDM/DVBT operation mode are active. Instead of
filling the kernel log in the latter case, print out a message to the debug
level and return 0 (this isn't used in the calling drxk_get_stats() anyway).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sakari Ailus [Thu, 9 Mar 2017 10:22:11 +0000 (07:22 -0300)]
[media] docs-rst: Make the CSI-2 bus initialisation documentation match reality
Update the CSI-2 bus documentation to tell that the LP-11 mode is not
mandatory as there are transmitters that cannot be explicitly set to LP-11
mode. Instead, say that this what the transmitter drivers shall do if
possible.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[media] et8ek8: Export OF device ID as module aliases
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Before this patch:
$ modinfo drivers/media/i2c/et8ek8/et8ek8.ko | grep alias
alias: i2c:et8ek8
Declare stv0299_config structures as const as they are only passed as
an argument to the function dvb_attach. dvb_attach
calls its first argument on the rest of its arguments. The first
argument of dvb_attach in the changed cases is stv0299_attach and
the parameter of this function to which the object references are passed
is of type const. So, stv0299_config structures having this property
can be made const.
First line shows the file size before patching and second one shows size
after patching.
text data bss dec hex filename
9572 926 40 10538 292a media/pci/dm1105/dm1105.o
9636 862 40 10538 292a media/pci/dm1105/dm1105.o
Declare mb86a16_config structure as const as it is either passed as
an argument to the function dvb_attach or is dereferenced. dvb_attach
calls its first argument on the rest of its arguments. The first argument
of dvb_attach in the changed case is mb86a16_attach and the parameter of
this function to which the object reference is passed is of type
const. So, mb86a16_config structures having this property can be made
const.
Bhumika Goyal [Sun, 19 Feb 2017 17:29:07 +0000 (14:29 -0300)]
[media] cx88: constify mb86a16_config structure
Declare mb86a16_config structure as const as it is only passed as
an argument to the function dvb_attach. dvb_attach calls its first
argument on the rest of its arguments. The first argument of
dvb_attach in the changed case is mb86a16_attach and the parameter of
this function to which the object reference is passed is of type
const. So, mb86a16_config structures having this property can be made
const.
Declare nxt200x_config structures as const as they are only passed as
an argument to the function dvb_attach. dvb_attach calls its first
argument on the rest of its arguments. The first argument of
dvb_attach in the changed cases is nxt200x_attach and the parameter of
this function to which the object references are passed is of type
const. So, nxt200x_config structures having this property can be made
const.
File size before:
text data bss dec hex filename
21320 3776 16 25112 6218 saa7134/saa7134-dvb.o
File size after:
text data bss dec hex filename
21384 3744 16 25144 6238 saa7134/saa7134-dvb.o
Bhumika Goyal [Sun, 19 Feb 2017 12:59:52 +0000 (09:59 -0300)]
[media] b2c2: constify nxt200x_config structure
Declare nxt200x_config structure as const as it is only passed as
an argument to the function dvb_attach. dvb_attach calls its first
argument on the rest of its arguments. The first argument of
dvb_attach in the changed case is nxt200x_attach and the parameter of
this function to which the object reference is passed is of type
const. So, nxt200x_config structures having this property can be made
const.
File size before:
text data bss dec hex filename
7566 568 0 8134 1fc6 common/b2c2/flexcop-fe-tuner.o
File size after:
text data bss dec hex filename
7582 536 0 8118 1fb6 common/b2c2/flexcop-fe-tuner.o
Colin Ian King [Fri, 17 Feb 2017 16:17:30 +0000 (14:17 -0200)]
[media] Staging: media/lirc: don't call put_ir_rx on rx twice
There is an exit path where rx is kfree'd on put_ir_rx and then
a jump to label out_put_xx will again kfree it with another
call to put_ir_rx. Fix this by adding a new label that avoids
this 2nd call to put_ir_rx for this specific case.
Detected with CoverityScan, CID#145119 ("Use after free")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Helen Koike [Fri, 7 Apr 2017 17:55:19 +0000 (14:55 -0300)]
[media] vimc: Virtual Media Controller core, capture and sensor
First version of the Virtual Media Controller.
Add a simple version of the core of the driver, the capture and
sensor nodes in the topology, generating a grey image in a hardcoded
format.
Signed-off-by: Helen Koike <helen.koike@collabora.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix small typo in Kconfig]
The HGT is a Histogram Generator Two-Dimensions. It computes a weighted
frequency histograms for hue and saturation areas over a configurable
region of the image with optional subsampling.
[media] v4l: vsp1: Support histogram generators in pipeline configuration
Histogram generators are single-pad entities that branch as leaf nodes
at any point in the pipeline. Make sure that pipeline traversal and
routing configuration support them correctly.
Support for the actual HGO and HGT operation will come later.
The metadata buffer type is used to transfer metadata between userspace
and kernelspace through a V4L2 buffers queue. It comes with a new
metadata capture capability and format description.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: removed left-over 'experimental' note]
[hans.verkuil@cisco.com: add newline after _v4l2-meta-format label]
Laurent Pinchart [Mon, 20 Jun 2016 09:07:08 +0000 (06:07 -0300)]
[media] v4l: vsp1: wpf: Implement rotation support
Some WPF instances, on Gen3 devices, can perform 90° rotation when
writing frames to memory. Implement support for this using the
V4L2_CID_ROTATE control.
Laurent Pinchart [Sun, 26 Feb 2017 12:44:18 +0000 (09:44 -0300)]
[media] v4l: Clearly document interactions between formats, controls and buffers
V4L2 exposes parameters that influence buffers sizes through the format
ioctls (VIDIOC_G_FMT, VIDIOC_TRY_FMT, VIDIOC_S_FMT, and possibly
VIDIOC_G_SELECTION and VIDIOC_S_SELECTION). Other parameters not part of
the format structure may also influence buffer sizes or buffer layout in
general. One existing such parameter is rotation, which is implemented
by the V4L2_CID_ROTATE control and thus exposed through the V4L2 control
ioctls.
The interaction between those parameters and buffers is currently only
partially specified by the V4L2 API. In particular interactions between
controls and buffers isn't specified at all. The behaviour of the
VIDIOC_S_FMT and VIDIOC_S_SELECTION ioctls when buffers are allocated is
also not fully specified.
This patch clearly defines and documents the interactions between
formats, selections, controls and buffers.
The preparatory discussions for the documentation change considered
completely disallowing controls that change the buffer size or layout,
in favour of extending the format API with a new ioctl that would bundle
those controls with format information. The idea has been rejected, as
this would essentially be a restricted version of the upcoming request
API that wouldn't bring any additional value.
Another option we have considered was to mandate the use of the request
API to modify controls that influence buffer size or layout. This has
also been rejected on the grounds that requiring the request API to
change rotation even when streaming is stopped would significantly
complicate implementation of drivers and usage of the V4L2 API for
applications.
Applications will however be required to use the upcoming request API to
change at runtime formats or controls that influence the buffer size or
layout, because of the need to synchronize buffers with the formats and
controls. Otherwise there would be no way to interpret the content of a
buffer correctly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stefan Brüns [Fri, 17 Feb 2017 00:55:31 +0000 (22:55 -0200)]
[media] si2157: Add support for Si2141-A10
The Si2141 needs two distinct commands for powerup/reset, otherwise it
will not respond to chip revision requests. It also needs a firmware
to run properly.
Cc: Evgeny Plehov <EvgenyPlehov@ukr.net> Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Antti Palosaari [Thu, 6 Apr 2017 12:17:42 +0000 (09:17 -0300)]
[media] si2157: revert si2157: Si2141/2151 tuner support
'Reset' loop does not look correct. I tested it very many times and
it never repeated those commands. If problem, it tries to solve,
really occurs on some situations better solution should be find out.
There is another patch which does not have such hackish looking loop.
Lets change to it.
Hans Verkuil [Mon, 10 Apr 2017 07:54:30 +0000 (04:54 -0300)]
[media] v4l2-tpg: don't clamp XV601/709 to lim range
The XV601/709 encodings are special: they signal limited range, but use the full range
to encode a larger gamut with R', G' and B' values outside the [0-1] range.
So don't clamp to limited range for these two encodings.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Philipp Zabel [Thu, 6 Apr 2017 14:03:40 +0000 (11:03 -0300)]
[media] coda: do not enumerate YUYV if VDOA is not available
TRY_FMT already disables the YUYV format if the VDOA is not available.
ENUM_FMT must do the same.
Fixes: d40e98c13b3e ("[media] coda: support YUYV output if VDOA is used") Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Philipp Zabel [Fri, 31 Mar 2017 13:33:26 +0000 (10:33 -0300)]
[media] tvp5150: fix pad format frame height
Even if field order is set to V4L2_FIELD_ALTERNATE, the width and height
values in struct v4l2_mbus_framefmt still refer to frame size, not field
size.
Fixes: 4f57d27be2a5 ("[media] tvp5150: fix tvp5150_fill_fmt()") Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Philipp Zabel [Fri, 31 Mar 2017 13:33:25 +0000 (10:33 -0300)]
[media] tvp5150: allow get/set_fmt on the video source pad
To let userspace propagate formats downstream in a media controller
scenario, the video source pad (now pad 1, DEMOD_PAD_VID_OUT) must allow
setting and getting the format. Incidentally, tvp5150_fill_fmt was
implemented for this pad, not for the new analog input pad (now pad 0,
DEMOD_PAD_IF_INPUT).
Fixes: 55606310e77f ("[media] tvp5150: create the expected number of pads") Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Colin Ian King [Thu, 23 Mar 2017 11:57:46 +0000 (08:57 -0300)]
[media] coda: remove redundant call to v4l2_m2m_get_vq
The call to v4ls_m2m_get_vq is only used to get the return value
which is not being used, so it appears to be redundant and can
be removed.
Detected with CoverityScan, CID#1420674 ("Useless call")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Tue, 4 Apr 2017 16:43:33 +0000 (13:43 -0300)]
[media] cec: fix confusing CEC_CAP_RC and IS_REACHABLE(CONFIG_RC_CORE) code
It is a bit confusing how CEC_CAP_RC and IS_REACHABLE(CONFIG_RC_CORE)
interact. By stripping CEC_CAP_RC at the beginning rather than after #else
it should be a bit clearer what is going on.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Reported-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Lee Jones [Tue, 4 Apr 2017 12:32:19 +0000 (09:32 -0300)]
[media] cec: Fix runtime BUG when (CONFIG_RC_CORE && !CEC_CAP_RC)
Currently when the RC Core is enabled (reachable) core code located
in cec_register_adapter() attempts to populate the RC structure with
a pointer to the 'parent' passed in by the caller.
Unfortunately if the caller did not specify RC capability when calling
cec_allocate_adapter(), then there will be no RC structure to populate.
This causes a "NULL pointer dereference" error.
Fixes: f51e80804f0 ("[media] cec: pass parent device in register(), not allocate()") Signed-off-by: Lee Jones <lee.jones@linaro.org> Cc: <stable@vger.kernel.org> # for v4.10 and up Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Tue, 13 Dec 2016 14:37:16 +0000 (12:37 -0200)]
[media] s5p-cec: add cec-notifier support, move out of staging
By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.
Update the bindings documenting the new hdmi phandle and
update exynos4.dtsi accordingly.
Tested with my Odroid U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> CC: linux-samsung-soc@vger.kernel.org Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Tue, 13 Dec 2016 13:07:17 +0000 (11:07 -0200)]
[media] exynos_hdmi: add CEC notifier support
Implement the CEC notifier support to allow CEC drivers to
be informed when there is a new physical address.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Kieran Bingham [Mon, 27 Feb 2017 13:40:34 +0000 (10:40 -0300)]
[media] v4l: vsp1: Register pipe with output WPF
The DRM object does not register the pipe with the WPF object. This is
used internally throughout the driver as a means of accessing the pipe.
As such this breaks operations which require access to the pipe from WPF
interrupts.
Register the pipe inside the WPF object after it has been declared as
the output.
Laurent Pinchart [Tue, 28 Feb 2017 22:44:55 +0000 (19:44 -0300)]
[media] v4l: vsp1: Disable HSV formats on Gen3 hardware
While all VSP instances can process HSV internally, on Gen3 hardware
reading or writing HSV24 or HSV32 from/to memory causes the device to
hang. Disable those pixel formats on Gen3 hardware.
projects / karo-tx-linux.git / log