Bruno Randolf [Tue, 9 Mar 2010 07:56:15 +0000 (16:56 +0900)]
ath5k: IQ calibration for AR5211 is slightly different
according to the HAL sources the calculation of the Q value is slightly
different for AR5211 chips.
i couldn't test this since IQ calibration never finishes on older parts. this
is a different problem...
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:55:55 +0000 (16:55 +0900)]
ath5k: remove ah_gpio_npins
it's never used and we have a newer implementation in gpio.c.
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:55:49 +0000 (16:55 +0900)]
ath5k: remove ah_mac_revision
it's not used, and we have ah_mac_srev.
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:55:44 +0000 (16:55 +0900)]
ath5k: remove ah_magic
it's never used. probably a leftover from the old OpenHAL days...
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:55:38 +0000 (16:55 +0900)]
ath5k: remove double opmode definition
opmode (operating mode) was defined in struct ath5k_hw and struct ath5k_softc.
remove it from ath5k_hw and use only from ath5k_softc (sc->opmode).
(btw: what's the meaning of opmode when we have multiple interfaces?)
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:55:28 +0000 (16:55 +0900)]
ath5k: preserve antenna settings
save antenna settings and preserve across resets.
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 9 Mar 2010 07:55:17 +0000 (16:55 +0900)]
ath5k: add antenna statistics and debugfs file for antenna settings
keep statistics about which antenna was used for TX and RX. this is used only
for debugging right now, but might have other applications later.
add a new file 'antenna' in debugfs (/sys/kernel/debug/ath5k/phy0/antenna) to show
antenna use statistics and antenna diversity related register values. it can
also be used to set the antenna mode until we have proper support for that in
iw:
- echo diversity > antenna: use default antenna mode (RX and TX diversity)
- echo fixed-a > antenna: use fixed antenna A for RX and TX
- echo fixed-b > antenna: use fixed antenna B for RX and TX
- echo clear > antenna: reset antenna statistics
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna [Thu, 4 Mar 2010 16:27:02 +0000 (18:27 +0200)]
rndis_wlan: copy only useful data from rndis_command respond
rndis_query_oid() uses full output buffer size to copy response buffer
from rndis_command()/device. This doesn't cause problems as response buffer
is sized based on output buffer but does copy extra unset bytes.
So change rndis_query_oid() so that only meaningful bytes are being copied.
Also in case of malfunctioning device/cable/etc returned data offset from
device might be wrong so bound check memory access correctly, so add
checks for this.
v2: fixed to use new netdev_dbg/warn/etc instead of old devdbg/warn/etc
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 1 Mar 2010 21:21:40 +0000 (22:21 +0100)]
minstrel: make the rate control ops reusable from another rc implementation
This patch makes it possible to reuse the minstrel rate control ops
from another rate control module. This is useful in preparing for the
new 802.11n implementation of minstrel, which will reuse the old code
for legacy stations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 1 Mar 2010 21:17:38 +0000 (22:17 +0100)]
minstrel: simplify and fix debugfs code
This patch cleans up the debugfs read function for the statistics by
using simple_read_from_buffer instead of its own semi-broken hack.
Also removes a useless member of the minstrel debugfs info struct.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the padding position is based on
ieee80211_get_hdrlen_from_skb(). This is not correct since the HW does
padding on RX (and expect the same padding to be present on TX) at the
following position :
- management : 24 + 6 if 4-addr format
- control : 24 + 6 if 4-addr format
- data : 24 + 6 if 4-addr format + 2 if QoS
- invalid : 24 + 6 if 4-addr format
whereas ieee80211_get_hdrlen_from_skb() is :
- management : 24
- control : 16 except for ACK/CTS where it is 10
- data : 24 + 6 if 4-addr format + 2 if QoS + 2 if QoS & order
- invalid : 24
So, correct frames are not affected : management frames do not use
4-addr format, control frames have no body and invalid frames are ...
not valid by definition. However, in order to use monitor interface for
debugging purpose, one must be able to send/receive any frames, be it
correct or not. Such frames are affected by incorrect padding.
Moreover, since padding is added on TX, we need to remove it before
calling ieee80211_tx_status. This affect TX packets received by monitor
interfaces.
It has been tested between an ath5k based card (AR5212) and an ar9170usb
based card (netgear WNDA3100) using a frame generator and a monitor
interface for each card.
Andres Salomon [Fri, 26 Feb 2010 00:18:47 +0000 (19:18 -0500)]
mac80211: give warning if building w/out rate ctrl algorithm
I discovered that if EMBEDDED=y, one can accidentally build a mac80211 stack
and drivers w/ no rate control algorithm. For drivers like RTL8187 that don't
supply their own RC algorithms, this will cause ieee80211_register_hw to
fail (making the driver unusable).
This will tell kconfig to provide a warning if no rate control algorithms
have been selected. That'll at least warn the user; users that know that
their drivers supply a rate control algorithm can safely ignore the
warning, and those who don't know (or who expect to be using multiple
drivers) can select a default RC algorithm.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 25 Feb 2010 06:15:28 +0000 (14:15 +0800)]
iwmc3200wifi: protect rx_tickets and rx_packets[] lists
Protect rx_tickets and rx_packets[] lists with spinlocks to fix the
race condition for concurrent list operations. In iwmc3200wifi both
sdio_isr_worker and rx_worker workqueues can access the rx ticket
and packets lists at the same time under high rx load.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 25 Feb 2010 06:15:27 +0000 (14:15 +0800)]
iwmc3200wifi: add ftrace event tracing support
Add event tracer for iwmc3200wifi driver. When enabled, all the
commands and responses between the driver and firmware (also
including Tx/Rx frames) will be recorded in the ftrace ring buffer.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 25 Feb 2010 06:15:25 +0000 (14:15 +0800)]
iwmc3200wifi: refuse to associate on unallowed channels
We need to make sure we don't associate with APs on unallowed
channels (according to regulatory setting). This could happen
when the channel is not specified (auto-select) within the
connection request. In this case we get the AP's channel until
the firmware indicates the association succeeded later. We need
to verify the associated channel. If the channel is disabled by
regulatory, we have to disassociate with the AP.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Abhijeet Kolekar [Fri, 26 Feb 2010 23:17:01 +0000 (15:17 -0800)]
iwl3945: check ucode load error code
Check successful completion of BSM loading. Give a chance to
load BSM again. If BSM loading is unsuccessful we should exit
and not initilize NIC. Before this checking even if the BSM loading failed
driver tries to initilize the NIC which should not be the case.
Johannes Berg [Wed, 24 Feb 2010 09:57:19 +0000 (01:57 -0800)]
iwlwifi: clean up queue/fifo handling
4965 hardware has 7 queues reserved and the
remaining ones used for aggregation, 5000
and higher need to have 10 reserved. This
is not very clear in the code right now,
unfortunately.
Introduce a new IWL_TX_FIFO_UNUSED constant
and make the queue/FIFO mapping arrays able
to hold that value, and change the setup
code to reserve all queues in the arrays
(the queue number is the index) and use the
new unused constant to not map those queues
to any FIFO.
Additionally, clear up the AC/queue mapping
code to be more understandable. The mapping
is the identity mapping right now, but with
the mapping function I think it's easier to
understand what happens there.
Finally, HCCA isn't implemented at all and
I think newer microcode removed it, so let's
remove all mention of it in the code, some
comments remain for 4965.
Johannes Berg [Fri, 19 Feb 2010 19:42:32 +0000 (11:42 -0800)]
iwlwifi: change WEP key protection to use mutex
For later station notification support we would like WEP key setting to be
done synchronously always. Currently all places from which WEP key is set
can sleep, but the usage of sta_lock prevents it to do so. Modify the
locking to use priv->mutex instead and thus enable this call to sleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 18 Feb 2010 08:36:07 +0000 (00:36 -0800)]
iwlagn: move sysfs flags and filter_flags files to debugfs
These files are incompatible with some changes
I'm making, and don't really belong into sysfs
anyway as they can only be used for debugging.
Since writing them will probably crash the
firmware, keep only the reading part and move
them into debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Wed, 17 Feb 2010 09:43:41 +0000 (01:43 -0800)]
iwlwifi: remove alive start adhoc restart
This code will never trigger, because when
we call this during interface start, neither
priv->vif nor priv->iw_mode conditions will
be true, and when it happens during reset
then priv->vif is also NULL. Also, in both
cases the same code will be executed as part
of iwl_bss_info_changed(), which contains a
copy of this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Fri, 22 Jan 2010 12:06:41 +0000 (04:06 -0800)]
iwlwifi: clear up AC/FIFO debug output
Not all queues are mapped for frame transmission,
so saying "AC" is misleading. They are all mapped
to FIFOs, obviously, though, so use that term and
also say AC/CMD instead of just AC for the queue
type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 21 Jan 2010 19:33:19 +0000 (11:33 -0800)]
iwlwifi: remove priv->active_rate_basic
This variable is assigned a default value,
but then assigned zero as soon as mac80211
calls a change channel (which will happen
right after the hw is started) and after
that it never changes again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 18 Feb 2010 18:56:57 +0000 (10:56 -0800)]
iwlwifi: remove frame dropping
With some of the new code in mac80211, public action
frames can be exchanged as non-injected frames even
while not associated.
Aside from that, dropping frames here is pointless
since we do deal with arbitrary frames that were
injected already, so let mac80211 make the decision
about which frames to allow or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 21 Jan 2010 15:32:58 +0000 (07:32 -0800)]
iwlwifi: remove dead code from iwl_mac_reset_tsf
iwl_mac_reset_tsf will only ever be called in
IBSS mode, so checking for other modes is not
useful and the code that depends on that will
not be executed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Tue, 19 Jan 2010 18:04:28 +0000 (10:04 -0800)]
iwlagn: remove write-only variables
Updating the variables last_rx_rssi, last_tsf
and last_beacon_time needs a lot of code but
they are not actually used in iwlagn (only in
3945) so we can move them to the 3945 specific
data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 21 Jan 2010 14:21:10 +0000 (06:21 -0800)]
iwlagn: move ICT code into separate file
All the ICT ISR code is iwlagn specific, and doesn't
need to be in iwlcore. So create a new iwl-agn.h
header file that will hold agn specific function
declarations etc., and move the ICT code into a new
iwl-agn-ict.c file that is linked into iwlagn. This
also gets rid of exporting those symbols.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 25 Feb 2010 14:13:11 +0000 (15:13 +0100)]
mac80211: use different MAC addresses for virtual interfaces
Drivers can now advertise to cfg80211 that they have
multiple MAC addresses reserved for a device, but we
don't currently make use of that in mac80211.
Change that and assign different addresses to new
virtual interfaces (if addresses are available) in
order to make it easier for users to use multiple
virtual interfaces; they no longer need to always
assign a new MAC address manually.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 24 Feb 2010 13:19:21 +0000 (14:19 +0100)]
mac80211: Improve software scan timing
The current software scan implemenation in mac80211 returns to the operating
channel after each scanned channel. However, in some situations (e.g. no
traffic) it would be nicer to scan a few channels in a row to speed up
the scan itself.
Hence, after scanning a channel, check if we have queued up any tx frames and
return to the operating channel in that case.
Unfortunately we don't know if the AP has buffered any frames for us. Hence,
scan only as many channels in a row as the pm_qos latency and the negotiated
listen interval allows us to.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Tue, 23 Feb 2010 23:15:27 +0000 (18:15 -0500)]
ath9k: never read from the AR_IMR_S2 register
The AR_IMR_S2 register sometimes cannot be read correctly. Instead of a
valid value, 0xdeadbeef is returned. The driver has been observed
writing that value back to AR_IMR_S2 after changing a few bits.
Cache the register value in ah->imrs2_reg and always write chached value
to the register.
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 23 Feb 2010 09:51:13 +0000 (18:51 +0900)]
mac80211: fix rates setup on IBSS merge
when an IBSS merge happened, the supported rates for the newly added station
were left empty, causing the rate control module to be initialized with only
the basic rates.
also the section of the ibss code which deals with updating supported rates for
an already existing station fails to inform the rate control module about the
new rates. as i don't know how to fix this (minstrel does not have an update
function), i have just added a comment for now.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Mon, 22 Feb 2010 06:38:42 +0000 (08:38 +0200)]
wl1271: Remove tx-power level workaround
This patch removes the workaround limiting chipset TX power to 12dB, instead
using the value configured by the mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Mon, 22 Feb 2010 06:38:41 +0000 (08:38 +0200)]
wl1271: Disable host TX rate control
Disable host TX rate control. The wl1271 firmware is already managing rate
control, so this eliminate unnecessary host processing.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Mon, 22 Feb 2010 06:38:40 +0000 (08:38 +0200)]
wl1271: Clean up TX security sequence number handling
Instead of managing the TX security sequence number as two variables, use
one 64 bit variable. This greatly simplifies the handling of the number.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Mon, 22 Feb 2010 06:38:39 +0000 (08:38 +0200)]
wl1271: Clean up firmware block allocation calculation
This patch simplifies the required block count calculation. Though it
introduces a division operator, it greatly simplifies the formula.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Mon, 22 Feb 2010 06:38:38 +0000 (08:38 +0200)]
wl1271: Update TX packet life time handling with higher resolution time
This patch uses a higher precision timer to synchronize with the firmware
clock. Improved precision is needed as on some platforms a jiffy may be up to
tens of milliseconds, and the required precision is closer to TU's.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Mon, 22 Feb 2010 06:38:37 +0000 (08:38 +0200)]
wl1271: Implement looped IRQ handling
This patch implements looped IRQ handling. In essence, if a new interrupt is
asserted by the FW while the host is processing the previous one, the host
will directly proceed processing the new IRQ without leaving the handling
function.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Mon, 22 Feb 2010 06:38:36 +0000 (08:38 +0200)]
wl1271: Don't mask interrupts while handling interrupt
Don't mask firmware interrupts while processing interrupts. This allows the
interrupt handler looping to work efficiently thus reducing interrupt
processing latency.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Mon, 22 Feb 2010 06:38:35 +0000 (08:38 +0200)]
wl1271: Aggregate RX acknowledgements to FW
This patch will ack RX frames read from the firmware in one single write,
instead of acking all the frames separately. This will reduce the amount of
required communication per frame.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the annoying and dmesg-flooding WLAN PSM entry/exit traces. Instead,
only output them if PSM traces are enabled.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Mon, 22 Feb 2010 06:38:33 +0000 (08:38 +0200)]
wl1271: Fix queue stopping/waking for TX path
The queue stopping/waking functionality was broken in a way that could
cause huge latencies in TX transfers and even cause the TX to stall in the
right circumstances. Correct these problems.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Mon, 22 Feb 2010 06:38:32 +0000 (08:38 +0200)]
wl1271: Fix ad-hoc mode neighborhood detection
This patch fixes a bug in ad-hoc mode preventing mac80211 from properly
detecting other ad-hoc networks with the same SSID.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Mon, 22 Feb 2010 06:38:31 +0000 (08:38 +0200)]
wl1271: Improvements to the TX path
- Fix a TX result overflow problem that was present in the TX path and visible
with at least linksys AP's (probably any AP with high throughput capability.)
- Optimize TX by writing FW trigger for a group of TX frames instead of
each and every frame.
- Slightly optimize the TX path code.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Mon, 22 Feb 2010 06:38:30 +0000 (08:38 +0200)]
wl1271: don't get received frames from hardware in PLT mode
Most probably patch "wl1271: add most of the normal initialization commands
to PLT mode" enabled the RX path in firmware so that now driver received
frames and passed them to mac80211, which warned about them.
Workaround this by not retrieving frames from the hardware, just ignore them.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Teemu Paasikivi [Mon, 22 Feb 2010 06:38:29 +0000 (08:38 +0200)]
wl1271: Fixed unloading of the wl1271_sdio module
Fixed two bugs causing problems when unloding wl1271 module. First was
missing sdio_set_drvdata call from the probe function, second was order
of function calls in the remove function.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Teemu Paasikivi [Mon, 22 Feb 2010 06:38:28 +0000 (08:38 +0200)]
wl1271: Changed access to fw status register to use raw read
Changed access to fw status register to use raw read instead of
translated addressing. On SDIO access by translated addressing was not
working and raw access is working also on SPI.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Teemu Paasikivi [Mon, 22 Feb 2010 06:38:25 +0000 (08:38 +0200)]
wl1271: Removed wl1271_spi.h and made some functions static
Removed wl1271_spi.h header as there's no more need to access functions
declared there outside of wl1271_spi.c. Also made those SPI access
functions static.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Fri, 19 Feb 2010 01:28:41 +0000 (20:28 -0500)]
ath5k: move ath5k_hw_register_timeout() into reset.c
ath5k_hw_register_timeout() was duplicated between phy.c and reset.c.
Since it is too big and too much used to be an inline function, move it
away from the ath5k.h header into reset.c. Remove _ATH5K_RESET and
_ATH5K_PHY defines.
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Fri, 19 Feb 2010 01:28:02 +0000 (20:28 -0500)]
ath5k: remove stale function declarations, make some functions static
Remove all unnecessary function declarations from ath5k.h. Comment out
unused functions. Remove ath5k_hw_get_tsf32(), which is too trivial to
be commented out. Make functions static if suggested by sparse. Make
ath5k_pm_ops static.
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 17 Feb 2010 20:27:26 +0000 (21:27 +0100)]
mac80211: deprecate RX status noise
The noise value as is won't be used, isn't
filled by most drivers and doesn't really
make a whole lot of sense on a per packet
basis -- proper cfg80211 survey support in
mac80211 will need to be different.
Mark the struct member as deprecated so it
will be removed from drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 3 Mar 2010 16:42:55 +0000 (17:42 +0100)]
rt2x00: Export rt2x00soc_probe from rt2x00soc
Export rt2x00soc_probe from rt2x00soc as it is used in rt2800pci.
Otherwise loading rt2800pci gives "rt2800pci: Unknown symbol
rt2x00soc_probe".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Mon, 1 Mar 2010 09:12:57 +0000 (14:42 +0530)]
mac80211: Fix HT rate control configuration
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Cc: stable@kernel.org Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 29 Jan 2010 19:54:56 +0000 (11:54 -0800)]
iwlwifi: load firmware asynchronously before mac80211 registration
At the wireless summit in Portland we discussed a way of
loading firmware asynchronously from ->probe() before
registration to mac80211, in order to register with the
wireless subsystems with complete information in cases
where firmware is required to know parameters.
This is not yet the case in iwlwifi, but for some new
features we're working on it will be the case since
those will only be supported by new firmware images.
Hence, to start with, convert iwlwifi to load firmware
asynchronously from probe, unbinding the device when
firmware loading fails, and only registering with the
wireless subsystems after firmware has been loaded
successfully.
Future patches will hook into this to register the
new firmware capabilities, depending on the firmware
API version.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:15:30 +0000 (13:15 +0100)]
ar9170: load firmware asynchronously
This converts ar9170 to load firmware asynchronously
out of ->probe() and only register with mac80211 when
all firmware has been loaded successfully. If, on the
other hand, any firmware fails to load, it will now
unbind from the device.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bryan Polk [Mon, 1 Mar 2010 17:23:28 +0000 (12:23 -0500)]
rt2x00: Add USB ID for CEIVA adapter to rt73usb
This adds support for CEIVA USB wireless adapters to the rt73usb driver.
Signed-off-by: Bryan Polk <sainth@eidolons.org> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit e1dd33f60ced091114e4aacf141e0d03b88d3e13 changed cfg80211 to
allow association commands while in associated state to enable support
for roaming within an ESS. However, this was not enough to resolve all
cases with mac80211 which needs some additional handling of the
reassociation case to clear internal state with the BSS that was in use
previously.
This patch makes ieee80211_mgd_assoc() accept a valid reassociation
command and clean the association state with the previous BSS. This
fixes roaming between BSSes in an ESS when using wpa_supplicant with
-Dnl80211.
Signed-off-by: Jouni Malinen <j@w1.fi> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Sat, 27 Feb 2010 06:12:34 +0000 (09:12 +0300)]
zd1211rw: fix potential array underflow
The first chunk fixes a debugging assert to print a warning about array underflows.
The second chunk corrects a potential array underflow. I also removed an assert
in the second chunk because it can no longer happen.
Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Benoit Papillault <benoit.papillault@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Matthew Garrett [Tue, 16 Feb 2010 21:36:25 +0000 (16:36 -0500)]
rfkill: Add support for KEY_RFKILL
Add support for handling KEY_RFKILL in the rfkill input module. This
simply toggles the state of all rfkill devices. The comment in rfkill.h
is also updated to reflect that RFKILL_TYPE_ALL may be used inside the
kernel.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log