Enable more flexible control over block ack:
- allow addba for any Tx vring
- allow to specify block ack timeout
- allow to delba for Tx or Rx side of any agreement; with reason
Renamed "addba" entry to "back"; it prints short help when read;
write:
- "add <ringid> <agg_size> <timeout>" to trigger ADDBA
If missing, <timeout> defaults to 0
- "del_tx <ringid> <reason>" to trigger DELBA for Tx side
- "del_rx <CID> <TID> <reason>" to trigger DELBA for Rx side
If missing, <reason> set to "STA_LEAVING" (36)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change default to support maximum number of associated
stations to an AP
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When encapsulating 802.3 frames into the 802.11 ones,
8-byte SNAP header added to save ethtype. SNAP is part of
the frame body, thus should be counted in MSDU. So,
MTU = MSDU - SNAP
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When configuring Tx/Rx VRING's, driver need to specify max. MPDU size
It should take into account all overhead introduced by 802.3->208.11
transformation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When establishing Block Ack as originator (Tx), control
AMSDU flag when sending ADDBA and update status upon
establishment flow completion. To be used in AMSDU flows
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When disconnecting single STA in AP, it might be that STA
in question is already disconnected. In this case, need to do nothing.
Previously, it was mis-interpreted as "disconnect all"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For manual ADDBA configuration, allow to set desired window size or
disable automatic mechanism.
Introduce module parameter (int) agg_wsize. It can be changed on run time,
will be taken into account on the next connect. Interpretation:
- <0 - disable automatic ADDBA; intended for manual testing through debugfs
- 0 - use automatically calculated window size
- >0 - use this for window size. Clipped by maximum supported by the hardware
with current environment.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon Tx vring creation, initiate BACK establishment
with maximum possible window size.
When establishing secure connection, there is EAPOL data exchange
between connection itself and "data port open", where security
is done and non-EAPOL data may be transferred. It is better to
send EAPOL frames using normal ACK because of firmware considerations.
send ADDBA only is 2 conditions met:
- data port open for the corresponded STA
- vring created
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce BACK establishment procedures; decision logic is not implemented
yet; debugfs entry 'addba' used to manually trigger addba/delba for ringid 0.
debugfs usage:
to establish BACK with agg_wsize 16:
echo 16 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba
to delete BACK:
echo 0 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba
to change agg_wsize, one need to delete BACK and establish it anew
ADDBA flow for:
- originator
Tx side (initiator) sends WMI_VRING_BA_EN_CMDID providing
agg_wsize and timeout parameters.
Eventually, it gets event confirming BACK agreement - WMI_BA_STATUS_EVENTID
with negotiated parameters. On this event, update Tx vring data
(struct vring_tx_data) and display BACK parameters on debugfs
- recipient
Rx side (recipient) firmware informs driver about ADDBA with
WMI_RCP_ADDBA_REQ_EVENTID, driver process it in service work
queue wq_service. It adjusts parameters and sends response
with WMI_RCP_ADDBA_RESP_CMDID, and final confirmation provided
by firmware with WMI_ADDBA_RESP_SENT_EVENTID. In case of success,
driver updates Rx BACK reorder buffer.
policy for BACK parameters:
- aggregation size (agg_wsize * MPDUsize)) to not exceed 64Kbytes
DELBA flow for:
- originator
driver decides to terminate BACK, it sends WMI_VRING_BA_DIS_CMDID
and updates struct vring_tx_data associated with vring; ignore
WMI_DELBA_EVENTID.
- recipient
firmware informs driver with WMI_DELBA_EVENTID,
driver deletes correspondent reorder buffer
ADDBA request processing requires sending WMI command, therefore
it is processed in work queue context. Same work queue used as for
connect, it get renamed to wq_service
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Miaoqing Pan [Fri, 19 Dec 2014 01:03:59 +0000 (06:33 +0530)]
ath9k: Add QCA956x HW support
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Miaoqing Pan [Fri, 19 Dec 2014 01:03:58 +0000 (06:33 +0530)]
ath9k: Fix register definitions for QCA956x
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Miaoqing Pan [Fri, 19 Dec 2014 01:03:57 +0000 (06:33 +0530)]
ath9k: Add initvals for QCA956x
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Miaoqing Pan [Fri, 19 Dec 2014 01:03:56 +0000 (06:33 +0530)]
ath9k: Add HW IDs for QCA956x
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 6 Jan 2015 15:58:06 +0000 (09:58 -0600)]
rtlwifi: rtl8192c-common: Convert driver to use common DM table initialization
These changes convert both rtl8192ce and rtl8192cu to use the new routine.
Some additional definitions are needed in the core, thus several of the
headers for other drivers are affected, but no other executable code is
changed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 6 Jan 2015 15:58:04 +0000 (09:58 -0600)]
rtlwifi: Create new routine to initialize the DM tables
Each of the drivers contains a routine that initializes the dm_digtable
member of the driver's private area. As a first step toward reducing the
size of the drivers, a copy of this driver is created in rtlwifi, and the
definitions of the parameters are moved there.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ram Amrani [Mon, 29 Dec 2014 06:24:04 +0000 (08:24 +0200)]
wlcore: add ability to reduce FW interrupts during suspend
Add the ability to mask FW interrupts on RX BA activity, PSM
entry/exit and fast-link notifications. This is used when the host
is suspended in order to decrease redundant wake ups.
Signed-off-by: Ram Amrani <ramrani@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Chen Gang [Wed, 24 Dec 2014 15:08:44 +0000 (23:08 +0800)]
wil6210: use 'uint64_t' instead of 'cycles_t' to avoid warnings
do_div() checks the type strictly. 'cycles_t' may be 32-bit under quite
a few architectures (parisc, arm, avr32 ...). So use 'uint64_t' instead
of, the related warning (with allmodconfig under parisc):
CC [M] drivers/net/wireless/ath/wil6210/debugfs.o
In file included from arch/parisc/include/generated/asm/div64.h:1:0,
from include/linux/kernel.h:124,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
drivers/net/wireless/ath/wil6210/debugfs.c: In function ‘wil_vring_debugfs_show’:
include/asm-generic/div64.h:43:28: warning: comparison of distinct pointer types lacks a cast
(void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
^
drivers/net/wireless/ath/wil6210/debugfs.c:107:4: note: in expansion of macro ‘do_div’
do_div(idle, total);
^
In file included from include/uapi/linux/stddef.h:1:0,
from include/linux/stddef.h:4,
from ./include/uapi/linux/posix_types.h:4,
from include/uapi/linux/types.h:13,
from include/linux/types.h:5,
from include/linux/list.h:4,
from include/linux/module.h:9,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
include/asm-generic/div64.h:44:18: warning: right shift count >= width of type [-Wshift-count-overflow]
if (likely(((n) >> 32) == 0)) { \
^
include/linux/compiler.h:159:40: note: in definition of macro ‘likely’
# define likely(x) __builtin_expect(!!(x), 1)
^
drivers/net/wireless/ath/wil6210/debugfs.c:107:4: note: in expansion of macro ‘do_div’
do_div(idle, total);
^
In file included from arch/parisc/include/generated/asm/div64.h:1:0,
from include/linux/kernel.h:124,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
include/asm-generic/div64.h:48:22: warning: passing argument 1 of ‘__div64_32’ from incompatible pointer type [-Wincompatible-pointer-types]
__rem = __div64_32(&(n), __base); \
^
drivers/net/wireless/ath/wil6210/debugfs.c:107:4: note: in expansion of macro ‘do_div’
do_div(idle, total);
^
include/asm-generic/div64.h:35:17: note: expected ‘uint64_t * {aka long long unsigned int *}’ but argument is of type ‘cycles_t * {aka long unsigned int *}’
extern uint32_t __div64_32(uint64_t *dividend, uint32_t divisor);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Amitkumar Karwar [Wed, 31 Dec 2014 10:36:44 +0000 (02:36 -0800)]
mwifiex: Increase priority of firmware download message
When driver is loaded, it is important to know if FW was already
active or it is freshly downloaded. This patch increases the
priority of these messages.
Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Marc Yang [Wed, 31 Dec 2014 10:36:40 +0000 (02:36 -0800)]
mwifiex: increase delay during card reset
200ms is the requirement to allow VDD1.1 and VDD1.8 to
drop to have proper reset.
Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Marc Yang <yangyang@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Marc Yang [Wed, 31 Dec 2014 10:36:39 +0000 (02:36 -0800)]
mwifiex: Adjust calling place of mwifiex_terminate_workqueue
Workqueue needs to be flushed early when removing card, otherwise
soft lockup issue may happen because main_process is triggered by
interrupt while card is being removed.
Signed-off-by: Marc Yang <yangyang@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Fri, 26 Dec 2014 11:02:34 +0000 (03:02 -0800)]
mwifiex: get supported BA stream info from FW
This patch adds support to get number of BA streams
supported information from FW. Some newer chips(e.g. 8897 series)
support 4 BA streams for TX; so driver should not disallow BA stream
setup just after 2 streams have been established.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Fri, 26 Dec 2014 11:02:32 +0000 (03:02 -0800)]
mwifiex: do not send key material cmd when delete wep key
This patch fixes memory corruption reported by community developer.
"Memory corruption occurs in mwifiex_ret_802_11_key_material_v1()
when a short command response is received without a key length
causing non initialised memory to be interpreted as the key
length resulting in a memcpy() overwriting the part of the
driver's private data structure beyond the key area."
For v1 key material API firmwares, there is no need to send
command to delete WEP key. WEP encryption/decryption is controlled
by mac_control command.
This patch avoids sending key material command in del_key case.
Reported-by: Martin Fuzzey <mfuzzey@parkeon.com> Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend van Spriel [Tue, 23 Dec 2014 18:04:23 +0000 (19:04 +0100)]
brcmfmac: Add support for bcm43340/1 wireless chipsets
This patch adds support for the bcm43340 and bcm43341 wireless
chipsets. These two chipsets are identical from wireless parts
perspective. As such they use the same firmware image.
Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Rob Herring <rob.herring@linaro.org> Signed-off-by: John Stultz <john.stultz@linaro.org>
[arend@broadcom.com: squash to single commit, remove 43341 chipid] Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Tue, 23 Dec 2014 13:44:12 +0000 (19:14 +0530)]
mwifiex: module parameter for deep sleep configuration
This patch adds module parameter for auto deepsleep configuration.
By default, module_param is 0 and auto deep sleep is enabled.
If mwifiex driver is loaded with disable_auto_ds=1, deep sleep
configuration would not be downloaded to FW and FW would not enter
deepsleep upon initializing.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Tue, 23 Dec 2014 13:44:11 +0000 (19:14 +0530)]
mwifiex: save sdio register values before firmware dump
This patch saves sdio registers value before firmware dump,
this can be used to find out reason for FW dump.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Tue, 23 Dec 2014 13:44:10 +0000 (19:14 +0530)]
mwifiex: save driver information to file when firmware dump
This patch adds support to dump driver information to a file
when firmware dump happens. This information can be used to
root casue FW crash.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Tue, 23 Dec 2014 13:44:09 +0000 (19:14 +0530)]
mwifiex: move debug_data dump function to common utililty file
mwifiex_debug_info also need be save to file when firmware dump happens.
Move its dump implementation function to commmon utilility file, thus it
can be reused in firmware dump function.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Tue, 23 Dec 2014 13:44:08 +0000 (19:14 +0530)]
mwifiex: move pm_wakeup_card_complete definition to usb.c
Move mwifiex_pm_wakeup_card_complete handler to source file.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Tue, 23 Dec 2014 13:44:07 +0000 (19:14 +0530)]
mwifiex: add rx histogram statistics support
This patch add a new debugfs item histogram used for reporting
rx data packet statitics(rx rate, snr, noise floor, signal strenth)
to userspace.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Tue, 23 Dec 2014 13:44:06 +0000 (19:14 +0530)]
mwifiex: add bcn_rcv_cnt and bcn_miss_cnt in getlog debugfs
This patch add receive beacon count and miss beacon count statistics
in debugfs getlog item.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Tue, 23 Dec 2014 13:44:05 +0000 (19:14 +0530)]
mwifiex: report tdls peers in debugfs
This patch add provision to show TDLS peer table in debugfs file.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When user-space uses a valid ISO-3166-1 country code for its
regulatory domain selection, the driver will try to configure
the firmware to use the same.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hante Meuleman [Sun, 21 Dec 2014 11:43:50 +0000 (12:43 +0100)]
brcmfmac: Change error log in standard log for rxbufpost.
When there is no room in the ring for rxbufpost an error is logged,
however this happens quite frequently and can be considered normal
and is certainly recoverable. This patch changes the erorr into
a normal msgbuf log.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hante Meuleman [Sun, 21 Dec 2014 11:43:49 +0000 (12:43 +0100)]
brcmfmac: Fix WEP configuration for AP mode.
When a device is configured for AP mode and it is configured for
WEP then the keys are plumbed first, followed by AP configuration.
During configuration a down command is given to the firmware which
will clear the configured keys. This patch reprograms the WEP keys
after AP has been brought up.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hante Meuleman [Sun, 21 Dec 2014 11:43:44 +0000 (12:43 +0100)]
brcmfmac: Fix incorrect casting of 64 bit physical address.
The physical addresses being used by pcie and msgbuf were using
a cast to long, which incorrectly caused it to limit the address
to 32bit. Now explicit u64 is used where needed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Tue, 6 Jan 2015 17:36:11 +0000 (19:36 +0200)]
Merge tag 'iwlwifi-next-for-kalle-2014-12-30' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* more work on d0i3 power state
* enhancements to the firmware debugging infrastructure
* support for 2 concurrent channel contexts
* fixes / cleanups in the rate control
* general cleanups
David S. Miller [Fri, 2 Jan 2015 21:47:51 +0000 (16:47 -0500)]
Merge branch 'timecounter-next'
Richard Cochran says:
====================
Fixing the "Time Counter fixes and improvements"
For this series I had only tested the build with ARCH=x86 and arm, but
others like sparc64, microblaze, powerpc, and s390 will fail because
they somehow don't indirectly include clocksource.h for the drivers in
question.
This series fixes the build issues reported by:
kbuild test robot <fengguang.wu@intel.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: cisco: enic: enic_dev: Remove some unused functions
Removes some functions that are not used anywhere:
enic_dev_enable2_done() enic_dev_enable2() enic_dev_deinit_done()
enic_dev_init_prov2() enic_vnic_dev_deinit()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log